X-BIM CAD Browser · 2019. 12. 6. · manufacturers. X-BIM CAD Browser allows you to use specific...

transcript

X-BIM CAD BrowserA short guide

TROX components, X-CUBE air handling

units and X-FANS

Version 1.08.00 (5. November 2020)

Introduction and overview What is the X-BIM CAD Browser……………………………………………………………………..[S.3 – S.5]

Installation assistance………………………………………………………………………………….......... [S.6 – S.11]

Use of the X-BIM CAD Browsers Menu and quick start ...…………….…………………………………………………………………….[S.12 – S.14] Configuration and import of TROX components………………………………………………[S.15 – S.22] Creation and import / export of EPF-Projects………………………………………………....[S.23 – S.27] Configuration and import / export of TROX air handling units………………………… [S.28 – S.40] Creation and import / export of TROX X-Fans devices……………………………………..[S.41 – S.48]

Further information…………………………………………………………………………………………………..[S.49 – S.50]

Agenda

X-BIM CAD Browser

Introduction and overview

X-BIM CAD Browser

X-BIM CAD Browser…

…has been developed in order to make designing safer and

easier for you. 3D modeling was used in many engineering

departments even before BIM.

No expert design is possible without product data from

manufacturers. X-BIM CAD Browser allows you to use

specific TROX components and TROX air handling units

with your Revit or AutoCAD application.

You can use the X-BIM CAD Browser also very easily to

create formats such as DWG, DXF, and IFC. This makes

three-dimensional planning with TROX products possible

with almost all model-based planning tools.

The X-BIM CAD Browser principle

TROX data source X-BIM CAD Browser Design software

Installation assistance

Installation and Update

General information & what to consider before and after

installation or update

The free installation file of the X-BIM CAD Browser can be

found in the BIM section of the TROX homepage and on the

liNear website (www.linear.eu) in the Data Sets TROX

section.

The X-BIM CAD Browser must be closed before installing an

update.

After installing or updating the X-BIM CAD Browser, please

also restart the Revit or AutoCAD application once to ensure

that the applications are properly linked.

First installation Update

Selection of the installation

language1

Selection for installation Selection for an update2.1 2.2

Selection of the locale.

The selection has an effect on

the availability of products.

If possible kepp the default target

directory.

When customizing the

destination directories, both

should point to the same drive.

Selecting different drives can

cause problems

• After installation, the computer should be restarted,to establish a connection between Revit / AutoCAD and the X-BIM CAD Browser.

Menu and quick start

to slide 14

Starting screen

Product selection

Bill of material

Project data

Strategies of use

1. Configure specific products on demand

Selecting and configuring the single product variant with the X-BIM CAD Browser

Adding the product to the 3D - planning

2. Importing a product or pre-configured EPF project file

Import of the product file or EPF project file (xml) into X-BIM CAD Browser

Adding the products to the 3D - planning

Configuration and import of TROX components

TROX EPF X-BIM CAD Browser Design software based on Revit

or AutoCAD

TROX components

Enter a product

name and start a

search

Select a product

by its name

Selecting a product type

Select a product

by its picture

Use one of these three options to

select a product1

Selecting a product variant

Click on Product to open the Easy Product

Finder to configure a variant2

Configuring a variant using the Easy Product Finder

Configure the

required variant using

the familiar Easy

Product Finder GUI

Click on to

transfer the selected

variant back to the

X-BIM CAD

Browser*

*You can only transfer variants for which there are geometry data in the Easy Product Finder.

Other features

Specification text DWG/DXF + product data sheet

Interactive

3D viewDisplay of the

specification text

with the technical

data for the

selected variant Documents

The product data

sheet is available

as PDF and with a

link to the product

Open 2D and 3D

DWG or DXF files

or copy them to the

clipboard

Transferring data to a project

*Which data is transferred exactly depends on the product.

Click on to transfer the

product variant to your current Revit

or AutoCAD project

6 Use the specific product model for

your project. Connections, order

code, specification text and

technical data* are also transferred

to Revit.

Other features

Selection of the display options of the

product

Component can be placed in CAD

program

By activation the product can be

placed several times

Replaces an existing product (in the

planning application) with the current

product from the X-BIM CAD

Browser.

Only the simplified geometry is

transferred to Revit/AutoCAD by

activation.

Selection of the transfer to Revit or

AutoCAD

Creation and import ofEPF projects

to slide 27

EPF project import

EPF project Project imported into X-BIM CAD Browser

Importing EPF projects into the X-BIM CAD Browser, makes it easy to use the product data of

products which are pre-configured in an EPF project.

Export the project file in XML format

1 2 Safe file (.xml) on your

computer3

Create project with

Export X-BIM file by selecting

in the “File”- menue

Import the project file in XML format

4Open “Project Import” in the

X-BIM CAD Browser

5Choose to open the dialog

box for selecting the project file and select the saved

XML-file which has been saved before (see step 3)

Overview of the project structure in the X-BIM CAD Browser

Products and

project structure

are displayed in

the browser.

Choose any product to transfer it

into the Revit/AutoCAD application6

Configure and import TROX air handling units

to slide 40

Principle of creating and integrating an X-BIM file for TROX air handling units

X-CUBE project file X-BIM CAD Browser Design software based on Revit

or AutoCAD

X-CUBE air handling units

AHU online configurator

TROX AHU sales

Data basis for air handling units

X-CUBE air handling units

AHU can be completely configured online

AHU is configured by a TROX AHU sales employee

Option 2

Option 1

Alternatively generation of geometry data in DXF, DWG and IFC formats

X-BIM CAD BrowserDesign software based on Revit

or AutoCAD

Create X-BIM file with AHU configurator [Option 1]

1TROX Homepage: Choose myTROX

and select the menue Design

2Choose AHU online

configurator.

A myTROX account is required to use

the AHU online configurator.

3After login to the myTROX account, start a

new project 4

Select the desired X-Cube variant, assign

position name and start configuration.

5Go through the menue and adjust the

default values acc. to your requirements.

Start calculation to create

your specific product

information.

After the calculation, several files can be downloaded, including the BIM data

for the TROX X-BIM CAD BROWSER.

Download X-BIM CAD Browser file

(xml data format)

Creation of X-BIM file by TROX AHU sales [Option 2].

Get X-BIM file from TROX X-CUBE Sales Team

1 Communicate specific AHU requirements.

CustomerTrox AHU- Sales

Transfer of the X-BIM product file in XML

format.2

Product is configured by the TROX-X-AHU sales team.

Importing AHU X-BIM file into X-BIM CAD Browser

Select X-CUBE category

in the X-BIM CAD

Browser product browser

2 Click on to open the dialogue

for selecting the project-specific X-CUBE xml or

zip file

Importing AHU X-BIM file into X-BIM CAD Browser

3 Select the project-specific zip or

xml file*

*Ask your TROX sales representative for the project-specific zip file or generate xml with the AHU online configurator.

Selecting a unit

4Select an air

handling unit

*Ask your TROX sales representative for the project-specific zip file.

4 Select the imported

Click to transfer the selected X-CUBE

air handling unit to your running Revit or AutoCAD

project

Optional:

Open 2D and 3D DWG,

DXF or 3D IFC files or

copy them to the

clipboard *

Data available for Revit applications

Geometry and

connectionsTechnical data and

additional attributes

Configure and import TROX X-FAN devices

X-FAN devices

Configuring and importing TROX X-FAN devices

X-FAN project file X-BIM CAD Browser Planning software based on

Revit or AutoCAD

Creation of X-BIM file by TROX X-FANS Sales

Get X-BIM file from TROX X-FANS Sales Team

1 Communicate specific X-FAN requirements.

CustomerX-FANS Sales

Transfer of the product file in XML format.2

Product is configured by the TROX X-FANS sales team.

Importing X-FANS X-BIM file into X-BIM CAD Browser

Select X-FAN1

2Select to opens the dialog box for

selecting the X-FAN ZIP or XML file.

Loading an X-BIM file from an X-FAN device

3 Select project specific ZIP or XML file

Selection of the imported device

4 Select the imported

Select to transfers the

X-FANS unit into the opened Revit or

AutoCAD project

Optional:

Open 2D and 3D DWG

and DXF files or copy

them to the clipboard

Available content for Revit applications

Technical data and

additional attributes

Geometry + connector

Further information

About X-BIM CAD Browser

Help menu1

Manual1.1

X-BIM CAD Browser is based

on a CAD browser by liNear

GmbH. For details on the

software please refer to the

manual. Please note that we

have adapted some browser

functions which is why the

liNear manual descriptions

may differ from the actual

product.

Version1.2