Post on 23-Nov-2023
transcript
Page 1
Scour Characteristics of Saturated Levees Due to
Floodwall Overtopping
Mazdak Karimpour1, Kyle Heinzl2, Emaline Stendback2, Kevin Galle2, Siavash
Zamiran3, and Abdolreza Osouli4, Ph.D., P.E.
1 Research Assistant, Dept. of Civil Engineering, Southern Illinois University Edwardsville,
Edwardsville, Illinois, 62026. 2 Undergraduate Assistant, Dept. of Civil Engineering, Southern Illinois University
Edwardsville, Edwardsville, Illinois, 62026. 3PhD Candidate, Instructor, Dept. of Civil Engineering, Southern Illinois University
Carbondale, Carbondale, Illinois, USA, Email: zamiran@siu.edu, zamirans@gmail.com,
Website: www.zamiran.net, Phone: +1 (618) 334-4572 4 Corresponding Author, Assistant Professor, Dept. of Civil Engineering, Southern Illinois
University, Edwardsville, Illinois, 62026; aosouli@siue.edu, Phone: +1 (618) 650-2816
Publisher: American Society of Civil Engineers
International Foundation Conference and Equipment Exposition. San Antonio, TX (IFCEE
2015)
Permalink: http://dx.doi.org/10.1061/9780784479087.117
Karimpour, M., Heinzl, K., Stendback, E., Galle, K., Zamiran, S., and Osouli, A. (2015)
Scour Characteristics of Saturated Levees Due to Floodwall Overtopping. IFCEE 2015: pp.
1298-1307.
doi: 10.1061/9780784479087.117
ABSTRACT: One of the major reasons of levee failure is erosion due to
overtopping. The overtopping of levees is occasionally the consequence of a flood or
Hurricane. In these events, the surface layers of levees become saturated in advance
of any overtopping due to rain and storm events. In this investigation, the effect of the
saturation ratio and almost vertical impingement of overtopped water from floodwall
on scour development are studied. For this purpose, laboratory-physical models of a
typical levee on the banks of Mississippi river with a scale of 1:20 were constructed.
A nearly 3 mm thick wooden plate, which was embedded in the crest of the levee
represented the floodwall. Silty soil materials with various saturation ratios were used
to observe scour potential of the soil. In all the tests, the scour development and the
stability of the wall were monitored and analyzed for each test during overtopping.
Hydraulic and geometric parameters including Densimetric Froude number,
compaction level, water content and levee dimensions were recorded to have a
representative comparison between the laboratory models and constructed levees in
practice. In addition, the erodibility of the levee materials was determined using
Erosion Function Apparatus (EFA). The results of EFA tests were compared to
physical model test results to explore and discuss the vulnerability of levee systems to
erosion when the surface soils are saturated and floodwall overtopping is experienced.
Keywords: Levee erosion, floodwall, levee, levee modeling, soil erosion, EFA test,
overtopping
Page 2
INTRODUCTION
Among many protection measures against floods, levees are the earthen structures
that are widely used on the bank of rivers and lakes to prevent the flood from causing
destruction. According to recent events of catastrophic floods worldwide including
the 2005 Katrina Hurricane (Briaud et al. 2008), Midwest floods in the U.S. in 2008
(Villarini et al. 2011) and the 2008 Hurricane Ike in the Caribbean Islands and Gulf
Coast (Tirpak 2009), the need for stronger and more stable protection measures
against these natural disasters is highly increasing.
In the overtopping process, water level exceeds top of the levee and causes erosion
in the crest and the body of levee. In some cases, floodwalls are constructed at the
crest of the levee to raise the height without any change in the body or geometry of
levee (Duncan et al. 2008). After the water level exceeds the top of the floodwall and
the overtopping process commences, the water starts to free fall from top of the
floodwall with high velocities. As the water nappe impacts the levee material, it
causes significant amount of erosion. The turbulence created due to this free fall,
increases the generated scour (Xiao, 2009).
Predicting the erosion due to overtopping can help in preventing levee failures.
Briaud et al. (2001) developed an apparatus called Erosion Function Apparatus (EFA)
to estimate the scour generation and erodibility of different types of soils. In this
apparatus, the soil is subjected to horizontal flow of water and is eroded. By using
these tests, the shear stress and the erodibility of the examined soil can be identified.
Kamalzare et al. (2013) performed numerical modeling on the scour generation and
overtopping of levees, associated with experimental tests on the simulated levees to
validate the results derived from the computer modeling. The performed laboratory
tests highlighted the importance of water flow parameters in overtopping process,
amount of erosion due to overtopping and the erodibility of soils while levee slope
does not show significant effect on the erosion. Hughes and Nadal (2009)
investigated scour generation in levees due to both wave overtopping and storm surge
overflow while studying hydraulic characteristics of the water flow on the levee. By
performing laboratory tests on simulated levees, experimental correlations concerning
overtopping discharge and wave volumes were developed. Although the provided
equations can only be used in the similar conditions to laboratory tests, they can
potentially be used to provide reasonable estimation of erodibility of levees. Several
investigations have also been conducted to prevent erosion using protection measures
on the land side of the levees (Li et al. 2012, Rao et al. 2012, and Johnson et al.
2013). Especially, Johnson et al. (2013) provided several experimental results for
protected levee erosion including ripraps, gravel, etc.
There are also some studies that evaluated the effect of change in degree of
saturation due to rain falls and drought on soil properties and the slope stability.
Shaikh et al. (1988) performed experimental tests to study the effect of saturation
degree on erosion rate of Na-montmorillonite clayey soils. Their results showed that
with a rise in saturation ratio, the erosion rate and soil erodibility increases. Vanapalli
et al. (1996) studied the effect of soil suction and saturation ratio on the shear strength
of different types of soils, and in particular high plastic clays. Their study show that
as the saturation ratio increases, the shear strength of the soil decreases.
Page 3
Prior to overtopping, the rain will saturate the levee material; therefore, affect the
erodibility characteristics of levee soil. In this investigation several laboratory tests
were performed on levees constructed with silty material and various saturation ratios
to identify the effect of levee material saturation prior to overtopping on erosion and
scour generation. The obtained results were also compared with EFA tests to identify
the compatibility and applicability of the conducted levee tests.
LABORATORY TEST SET UP
In order to investigate the erodibility and scour generation of levees subject to
floodwall overtopping, laboratory models of the levees along Mississippi river with 1
to 20 scale were constructed. A sharp wooden plate was placed on the crest of the
levee representing the embedded floodwall. The constructed levees inside the box
were 0.23 m (9 in) wide, 2.1 m (7 ft) long and the top of the levee was 0.35 m (14 in)
from ground surface (Figure 1). 75 percent of the floodwall was embedded in the
levee and the top of the floodwall was 0.47 m (18.5 in) from the ground surface.
FIG. 1. Cross section and top view of constructed levees in laboratory
Different sets of tests including Sieve Analysis (ASTM D1921), Plasticity Index
(ASTM D4318), Compaction (ASTM D698) and EFA tests were performed on a
variety of material. The soil used for construction of the levees was classified as low
plasticity silty soil (ML) with plasticity index of 7 %. Standard Proctor test
(compaction test) showed the optimum moisture content of 19% and the maximum
dry density of 17 kN/m3.
The levee construction process included several steps. In the first step, the scaled
levee was constructed at 80% of the maximum density based on the
Standard Proctorin several 7.5 cm (3 in) thick layers. Each layer was compacted using
a hand tamper. After compaction of each layer, three samples were taken to verify the
compaction levels. Then, water was sprayed on levee surface to simulate rain and
change in saturation ratio of levee material. After spraying water on the material,
three samples were also taken to check the saturation ratio of the soil. The values of
moisture content and compaction level were tried to keep constant by equal spraying
and compacting frequencies for each 7.5 thick layers, respectively.
0 cm 15 cm 30 cm
Page 4
For EFA tests, in addition to low plasticity soil material, specimen with higher
plasticity indices were tested. The higher plasticity samples were prepared using 1 to
1 and 2 to 1 ratio of high plastic clayey to low plastic silty material. EFA tests were
performed on these samples with varied plasticity indices and saturation ratios. The
samples were soaked in water before testing to reach different saturation levels. The
summary of each EFA and levee test is shown in Table 1. The procedure for
monitoring the scour variation during overtopping and providing the results provided
by Johnson et al. (2013) tssts hs rosid si si.sdsst eitre hstesteiorhtoitre,s rdesres is
l.s ornth hs id s t ott ei ls o stliss ros ht o eis ori oitres t idrhss ros l n s.s
rrv n o,s oorohtels irso l s1ss n o ls t ott ei ls i siss o s hre s tes idtss sithts irs
ten sitl i sid s orht tltitsr ste ori oi hsl n ss s hsresn ot itresr sid tos oitn s
o t i os.
TABLE 1. Specifications of the material used for EFA and levee tests
Test
No. EFA Levee Material
Plasticity
Index
Compaction
Level (%)
Saturation
Ratio (%)
1 ML 6.9 85 58.7
2 ML 6.9 85 22.7
3 1:1 Ratio 13.9 85 50.9
4 1:1 Ratio 13.9 85 58.2
5 1:1 Ratio 13.9 85 91.7
6 2:1 Ratio 17.7 85 46.7
7 2:1 Ratio 17.7 85 86.3
8 ML 6.9 80 43.8
9 ML 6.9 80 85.3
10 ML 6.9 80 91.4
After setting up the levee for the desired test, the reservoir (i.e. water-side of the
levee) was filled with water and the water flow overtopped the floodwall. Special
attention was made to avoid wave actions in these series of tests. The generated nappe
due to overtopping process started erosion of the levee material. In order to keep the
water circulating as the test continued, the excess water was collected and pumped to
reservoir. The test was continued until scour depth and width reached equilibrium.
Monitoring hydraulic and geometric specifications of scour was conducted during
each test. One of the most important hydraulic characteristics of flow, when overtopping is in
progress, is Densimetric Froude number (Eq. 1) which allows to compare the flow in
full and lab scaled models (Johnson et al. (2013).
𝐹𝑟𝑑 = √𝑢2 + 𝑤2/√𝑔∗𝑑50 (1)
Where, w is the vertical velocity at the impact point of water to soil, u is the
horizontal velocity component, g* is moderated gravity acceleration and is defined as
𝑔(𝑆𝐺 − 1)(1 − 𝑛), SG is the specific gravity of soil solids, n is the porosity of the
Page 5
soil and d50 is the median grain size of soil particles used in construction of the levee.
Vertical velocity can be estimated by free falling equation which is √2𝑔ℎ . It is
noteworthy that h is the falling height which is the height of top of the floodwall to
the depth of the scour. According to Johnson et al. (2013) the range for Densimetric
Froude number in the field is from tens to thousands.
RESULTS AND DISCUSSION
A typical scour profile is shown in Figure 2. The scour depth and scour width are
demonstrated in this figure. The scour depth variation during floodwall overtopping
was monitored and it is shown in Figure 3. The scour profile in the first 90 seconds of
the test is also shown in Figure 4. Test results show that by changing the saturation
ratio, the scour depth’s variation with time is different for levees with different
saturation levels. According to these observations, with greater saturation levels, there
is less erosion happening in the early stages of overtopping. Also, creation of the
scour hole behind the wall is more pronounced in levees with low saturation levels. In
levees with high saturation levels or fully saturated, the erosion profile does not show
a bowl shape scour immediately behind the wall. This might be due to the fact that in
higher saturation levee tests, the overflooded water will start running off the levee
surface rather than penetrating the soil or causing bowl shaped scour. It is noteworthy
that although the results in figures 3 and 4 are presented for the first 300 and 90
seconds, respectively, but duration of the tests extended to more than 1000 seconds.
However, the equilibrium scour depth and length reached approximately at 300th
second.
FIG. 2. The measures of scour depth and length in the experimental study
Page 6
FIG. 3. Effect of saturation ratio on scour depth for lab-scaled tests on levees
constructed with silty soils and compaction ratio of 80%
0
2
4
6
8
10
12
14
16
18
0 50 100 150 200 250 300
Sc
ou
r D
ep
th (
cm
)
Time (s)
Test No. 8
Test No. 9
Test No. 10
0
2
4
6
8
10
12
14
16
18
0 100 200 300 400
Sco
ur
Dep
th (
cm)
Time elapsed (s)
Levee-ML-44
Levee-ML-85
Levee-ML-91
Page 7
Fig 4. Scour profile for a) Test No. 8., b) Test No. 9., and c) Test No. 10.
Figure 5 shows the Densimetric Froude number for the levee tests. This figure
shows the scaled model levee test covers the lower range of Densimetric Froude
numbers typically observed in the field or full-scaled models. In all the tests, this
parameter increases with time of flooding as the water fall height increases due to
scour development.
The general flow condition during the tests is a vertical flow passes from the
floodwall and generates a thin nappe after overtopping. Accordin to Figure 5, the
Densimetric Froude number of the flow varies from 90 to 150 during the test.
Figure 6 compares the scour rate versus time for same levee material with different
saturation ratios. In this figure the scatters after 200th second show that the soils with
higher saturation ratios have more resistance against the scour while overtopping is in
progress. According to this figure the average of scour rate in different times for drier
soils is higher than more saturated soils.
Figure 7 shows the comparison of EFA and levee test results. It is observed that in
EFA tests for similar material, with a rise in saturation ratio, the erosion rate for
samples with higher plasticity indices will increase significantly while for low
plasticity material (i.e. ML), the erosion rates remain relatively unchanged. It can also
be noted that as the water velocity increases, the amount of scour rate increases. This
figure also shows that an increase in plasticity of material will result in decrease in
the scour rate and erodibility of material.
Scour Length (cm)
101520253035 0
20
25
30
35
5
Scour Length (cm)
Sco
ur D
epth
(cm)
1015202530350
15
20
25
30
35
5
Scour Length (cm)
Sco
ur D
epth
(cm)
1015202530350
15
20
25
30
35
5
Sco
ur D
epth
(cm)
a)b)
c)
Legend
60 S Scour Line
90 S Scour Line
45 S Scour Line
30 S Scour Line
15 S Scour Line
10 S Scour Line
5 S Scour Line
Page 8
FIG. 5. Densimetric Froude Number versus time for silty materials with 80 %
compaction ratio and different saturation ratios
80
90
100
110
120
130
140
150
160
170
0 50 100 150 200 250 300
Den
sim
etr
ic F
rou
d N
um
be
r
Time (s)
Test No. 8
Test No. 9
Test No. 10
80
90
100
110
120
130
140
150
160
170
0 50 100 150 200 250 300
Den
sim
etri
c F
rou
d N
um
ber
Time (sec)
Levee-ML-44
Levee-ML-85
Page 9
FIG. 6. Scour rate versus time for the scaled levee tests
According to Figure 7, while the water flow velocity for levee simulated tests are
lower than EFA, their scour rates are within the same range as for EFA tests. This
indicates that more scour and erosion is developed in levee simulated tests than EFA
tests for the same material. The reason for the difference in erodibility of same
material used for both levee and EFA tests is the erosion mechanism in each test. In
EFA test the horizontal water flow erodes the compacted layered soil, while in lab-
scaled levee tests, free water fall overtopped from floodwall impinges the levee
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
0 50 100 150 200 250 300
Sc
ou
r ra
te (
mm
/ho
ur)
Time (s)
Test No. 8 Test No. 9 Test No. 10
0
500
1000
1500
2000
2500
3000
3500
4000
4500
5000
0 50 100 150 200 250 300
Sco
ur
rate
(m
m/h
ou
r)
Time (second)
Levee-ML-44 Levee-ML-85 Levee-ML-91
Page 10
surface and erodes the material. Because of the impact of the water jet to the soil
layer and the turbulence created due to this phenomenon, the erodibility of levee
material is more severe. Generally, individual EFA tests can provide a rough
estimation of the erodibility of levees during the overtopping. However, as mentioned
before, EFA can just provide the erodibility potential of soils based on horizontal
flow which is not applied in levee overtopping. Therefore, for more accurate
investigation, scaled levee tests are required to generate free water fall during the
overtopping.
The comparison between EFA and levee results confirms that for low plastic silts the
saturation level variation does not significantly affect the scour rate in longer duration
of floods. However, a slight increase in scour potential was observed in levee tests
with less saturation levels. The reason for this occurrence might be the fact that, when
silty material is exposed to moisture, it will experience more cohesiveness and can
bind the particles more than when it is drier. Consequently, the levee material shows
higher resistance against induced shear stresses and erosion due to overtopping.
CONCLUSION
Erosion due to floodwall overtopping can result in levee breach. In order to study
the effect of saturation level of levee material on erosion rate, several lab-scaled tests
on levees and EFA tests were performed. Levee materials for all these tests were the
same but different saturation ratios representing rain duration in advance of
overtopping were considered. The results of these tests show that the scour rate for
low plasticity silty materials with different saturation ratios is almost the same in EFA
tests and show slight differences in levee simulated tests. However, due to difference
in mechanism of scour in simulated levee and EFA tests, the erodibility potential of
material in simulated levees is greater. The comparison of these results shows that
because of higher induced shear stresses due to free fall of water in overtopping
process, the erodibility of levee material is significantly higher than the erodibility of
soil samples in EFA tests. Based on the EFA test results, silty soil material had the most
erosion rate. Accordingly, 1:1 ratio soil material had more erosion rate than 2:1 ratio soil
material. This means that based on EFA tests, the erosion rate decreases with increase on
plasticity index.
Page 11
FIG. 7. Scour rate versus impact velocity for laboratory levee and EFA tests
1
10
100
1000
10000
100000
0 1 10
Ero
sio
n r
ate
(m
m/h
r)
Velocity (m/s)
Test No. 1 Test No. 2 Test No. 3 Test No. 4 Test No. 5
Test No. 6 Test No. 7 Test No. 8 Test No. 9 Test No. 10
1
10
100
1000
10000
100000
0 1 2 3 4 5
Ero
sion
rate
(m
m/h
r)
Velocity (m/s)
EFA-ML-58 EFA-ML-22 EFA-1:1-51 EFA-1:1-58
EFA-1:1-92 EFA-2:1-47 EFA-2:1-86 Levee-ML-44
Levee-ML-85 Levee-ML-91
Page 12
REFERENCES
ASTM D698-07. (2007). “Standard Test Methods for Laboratory Compaction
Characteristics of Soil Using Standard Effort.” Annual book of ASTM standards.
4.08, Philadelphia, Pennsylvania.
ASTM D1921-07. (2007). “Standard Test Methods for Particle Size (Sieve Analysis)
of Plastic Materials.” Annual book of ASTM standards. 4.08, Philadelphia,
Pennsylvania.
ASTM D4318-05. (2005). “Standard Test Methods for Liquid Limit, Plastic Limit,
and Plasticity Index of Soils.” Annual book of ASTM standards. 4.08,
Philadelphia, Pennsylvania.
Briaud, J., Chen, H., Govindasamy, A. and Storesund, R. (2008). “Levee erosion by
overtopping in New Orleans during the Katrina Hurricane.” Journal of
Geotechnical and Geoenvironmental Engineering. 134 (5): 618–632.
Briaud, J.-L., Ting, F., Chen, H.C., Cao, Y., Han, S.W. and Kwak, K.W. (2001)
“Eorstres Fteoitres d o itss ros Sortos R i s Po htoitres.”s Journal of
Geotechnical and Geoenvironmental Engineering. 127 (2): 105-113.
Duncan, J.M., M.ASCE, Brandon, T.L., M.ASCE, Wright, S.G., M.ASCE and
Vroman, N., M.ASCE.s (2008)s “Stability of I-Walls in New Orleans during
Hurricane Katrina.” Journal of Geotechnical and Geoenvironmental Engineering.
134: 681-691.
Hughes, S.A. and Nadal, N.C. (2009). “Laboratory study of combined wave
overtopping and storm surge overflow of a levee.” Coastal Engineering.56: 244–
259
rdesre,sE.B.,so sitk,sF.Y.,sR ntod eho e,sN.,sSodrrl o,s .,s2013,s“L n ssortos orts
rn oir tels sirotsv n ss ehs sortos ortei ot sto s”,sOcean Engineering, 57,
p.p. 72-82.Kamalzare, M., Han, T., McMullan, M., Stuetzle, C., Zimmie,
T., Cutler, B., and Franklin, W. (2013) “Computer Simulation of Levee Erosion
and Overtopping.” In: Meehan, C., Pradel, D., Pando, M.A., Labuz J.F.
(eds).Proc. Geo-Congress at Stability and Performance of Slopes and
Embankments; March 3-7, 2013, San Diego, United States. pp. 1851-1860.
Li, L., Pan, Y., Amini, F. and Kuang, C. (2012). “Full scale study of combined wave
and surge overtopping of a levee with RCC strengthening system.” Ocean
Engineering. 54:70–86
Rao, X., Li, L., Amini, F. and Tang, H. (2012). “Strrid hsP oitol srthorhte ttoss
Modeling of Combined Wave and Surge Overtopping and Hydraulic Erosion of
an Articulated Concrete Block-Sio elid e hsL n sStsi t.” Journal of Coastal
Research. 28 (6): 1500 –1511.
Shaikh, A., Ruff, J.F. and Abt, S.R. (2011). “Erosion Rate of Compacted Na-
Montmorillonite Soils.” Journal of Geotechnical engineering. 114 (3): 296-305.
Tirpak, S. M. (2009). “United States army corps of engineers, Galveston district
operational experiences and response to Hurricane Ike.” Shore and Beach. 77 (2):
60–70.
Vanapalli, S.K., Fredlund, D.G., Pufahl, D.E. and Clifton, A.W. (1996). “Mrh ls ros
id s o htoitres r s sd os sio elids vtids o s ois irs srtls stoitre.”s Canadian
Geotechnical Journal. 33: 337-392.
Page 13
Villarini, G., Smith, J.A., Baeck, M.L. and Krajewski, W. (2011). “Examining flood
frequency distributions in the Midwest U.S.” American Water Resources
Association. 47 (3): 447–4
Xiao, H., Huang, W. and Tao, J. (2009). “Numerical modeling of wave overtopping a
levee during Hurricane Katrina.” Computers and Fluids. 38 (5), 991–996.