Updated on 11.9.2014

CURRICULUM VITAE

Education 1. PhD Automotive Engineering, 2011, Universiti Putra Malaysia, MALAYSIA 2. M Eng Electrical Engineering, 2001, Universiti Teknologi Malaysia.MALAYSIA 3. B Eng Electrical and Electronic Engineering, 1998, University of Porstmouth, UNITED KINGDOM

Areas of Interest 1. Control system, System Identification and Automotive Electronic Control

Professional Qualification/ Membership/ Affiliation 1. Member, Society of Automotive Engineering: 611339404 2. Member, Malaysia Society of Engineering & Technology (mSET) :00751 3. Member , Institute of Electrical and Electronics Engineers (IEEE): 80260879 4. Member, International Association of Engineer (IAENG): 115244 5. Senior Member, Science and Engineering Institute (SCIEI) :0060 6. Graduate Member, Board of Engineers Malaysia (BEM): 35786A 7. Member, The Institute of Engineers, Malaysia (IEM) :48508

Appointment 1. Senior Lecturer, Department of Electrical and Electronic Engineering Faculty

of Engineering, UPM 1/2008 to date

2. Associate Researcher, Center of Power and Advanced Energy (CAPER) (CAPER), Faculty of Engineering, UPM

3. Academic Researcher, PROTON Professor Office, Engineering Division

Perusahaan Otomobil National Sdn Bhd.(Malaysian automobile manufacturer) 4. Associate Researcher, Institute of Advanced Technology (ITMA), UPM 5. Lecturer, Department of Electrical and Electronic Engineering Faculty of

Engineering, UPM 6. Tutor, Department of Electrical and Electronic Engineering Faculty of

Engineering, UPM

7/2014-7/2017 2/2012- 2/2013 2013-2016 7/2001- 12/2007 5/1999- 6/2001

Appointment-Managerial Duties 1. Department of Electrical and Electronic Eng, Development’s Coordinator 2. Head of Control and Automation Laboratory 3. Final Year Project Coordinator 4. Head of Control Unit, Dept.Of Electrical and Electronic Engineering 5. Facilitator program: UNITI College-UPM : for Bachelor Program in Electrical

and Electronic 6. Fellow of College 14, Universiti Putra Malaysia

9/2014-to date 2013-to date 2013-to date 2008-2011 2002-2003 2003-2005

Dr. Mohd Khair Hassan Department of Electrical and Electronic Engineering, Faculty of Engineering, Universiti Putra Malaysia, 43400 UPM Serdang, Selangor T: 03-8946 4367 F: 03-8768 6327

Updated on 11.9.2014

List of Subjects Tought

1. EEE 3001: Electrical and Electronic Technology 2. EEE 3401 : Control System 3. EEE 4403 : Advanced Control System Design 4. EEE 4404 : Intelligent Control System 5. EEE 4405 : Embedded Control System 6. EEE 5999 : Advanced Modelling and Simulation

Year 2 Year 3 Year 4/MSc Year 4/MSc Year 4/MSc MSc/ PhD

Journal Publications 1. Ameer Sedera, Mohd Khair Hassan,Mohd Amran Bin Mohd Radzi and SF Tohad, Mathematical

Design and Analysis of Anti-Lock Brake System for Electric Vehicle Based On Brake-By-Wire Technology, International Journal of Electric and Hybrid Vehicles; 2014 (Reviewed ) (SCOPUS)

2. Nor Aziah Mohd Azubir, Mohd Khair Hassan, Hairi Zamzuri, Saiful Amri Mazlan, Development of PROTON Electric Vehicle Control Unit (eVCU) using State Machine Deterministic Rule-Based Approach Applied Mechanics and Materials ISSN: 1660-9336, Accepted for publication 2013 (ISI indexed)

3. Seyed Mohammad Hussein S, Siti A. Ahmad, Azura Che Soh, Mohd K Hassan, Asnor J Ishak.The

Combined Statistical Minimized Point Distance (SMPD) and Texture Based Image Processing Techniques and Their Applications in Plant Species Recognition. Submitted to IET Image Processing. 2014. (ISI Indexed)

4. Ahmed Abdulelah, Azura Che Soh,MohdKhair Hassan and SamsulBahariMohd Noor. Controlling the Pitch and Yaw Angles of Twin Rotor MIMO System in Simulation Based Platform using Fuzzy Logic. Open Journal of Artificial Intelligence , OJAI 2014, (1):1-6 (DOI:10.12966/ojai.02.01.2014)

5. Nor Hafeezah Kamarudin, Siti Anom Ahmad, Mohd Khair Hassan, Rosnah Mohd Yusuff,Siti Zawiah Md Dawal: A Review of the NIOSH Lifting Equation and Ergonomics Analysis, Advanced Engineering Forum Vol. 10 (2013) pp 214-219. (DOI:10.4028/www.scientific.net/AEF.10.214)

6. Seyed Mohammad Hussein S, Siti A. Ahmad , Azura Che Soh, Mohd K Hassan, Asnor J Ishak

Introducing New Statistical Shape Based and Texture Feature Extraction Methods in The Plant Species Recognition System. International Journal of Engineering and Technology, Vol.10, No. 2, 56–61, 2013

7. Mohd Hafiz Mohd Nordin, Mohd Khair Hassan, Azura Che Soh, Mohd Amran Mohd Radzi, Hardware-

In-Loop of Fault Detection system for Air-Fuel Ratio Control ,Applied Mechanics and Materials ISSN:

1660-9336, Accepted for publication (ISI indexed) 2013

8. M.Seifi, A.che Soh, N.I.Abd.Wahab, M.K.Hassan, A Comparative Study of PV Models with Matlab/Simulink, World Academy of Science, Engineering and Technology 74 2013, pp 108-113

9. M.Seifi, A.che Soh, N.I.Abd.Wahab, M.K.Hassan, Modeling of PV Standalone Microgrid Based on IEEE

1562-2007,1361-2003 and 1013-2007. International Review on Modeling and Simulations (I.R.E.M.O.S), vol 6,N2, 2013 pp 515-525. (SCOPUS)

10. M.K Hassan, N.A.M. Azubir, Nizam.H.M.I, S.F Toha, B.S.K.K Ibrahim , Optimal Design of Electric Power

Assisted Steering System (EPAS) Using GA-PID Method , Procedia Engineering 41 (2012) 614-621. (SCOPUS).

11. B.S.K.K.Ibrahim, N.Aziah.M.A, S. Ahmad, R. Akmeliawati, Nizam H.M.I,A.G.A.Muthalif, S.F.Toha and

M.K.Hassan, Fuzzy-based Temperature and Humidity Control for HVAC of Electric Vehicle, Procedia Engineering 41 ( 2012 ) 904 – 910. (SCOPUS).

12. S. F. Toha, N. H. F. Ismail, N. A. M. Azubir, H. M. I. Nizam, M. K. Hassan, B. S. K. K. Ibrahim, Lithium

Iron Phosphate SOC prediction for Efficient Electric Vehicle, Advanced Materials Research, ISSN: 1022-6680. Accepted for publication. (SCOPUS). 2012

13. Mohd Khair Hassan and Ishak Aris, Modeling brake torque of CNGDI using two stage regression

technique , International Review of Mechanical Engineering (2012) Vol. 6 n. 3, pp. 621-624 (SCOPUS)

Updated on 11.9.2014

14. Mohd Azubir N.A, Md.Idris N.H, Ahmad S, Akmal R.A, Toha S.F, Ibrahim B.S.K.K , Hassan M.K.

Development of Control Strategy on Segregation of HVAC Energy Efficiency as Non Propulsion Electrical Hotel Load in EV. Journal of Engineering. Vol 4. Pg 14-20. 2012

15. Mohd Khair. H, Aishawarya.K, Ribhan Zafira A.R and Siti Anom.A, Design a PID Controller for a

Constant Speed of Combustion Engine, Australian Journal of Basic and Applied Sciences, 5(12): 1586-1593, 2011 (SCOPUS).

16. M.K. Hassan, R.Z. Abdul Rahman, A,Che Soh, M.Z.Z Ab Kadir, Lightning Strike Mapping for Peninsular

Malaysia Using Artificial Intelligence Techniques. Journal of Theoretical and Applied Information Technology (JATIT) 34(2), 2011, 202-214. (SCOPUS).

17. Azura Che Soh, Mohd Khair Hassan, Ribhan Zafira Abdul Rahman, A Fuzzy Classificier System for

Malfuntion Traffic Light System Classification, Journal of Theoretical and Applied Information Technology (JATIT) 34(2), 2011, 226-240. (SCOPUS).

18. Mohd Khair. H, Aishawarya.K, Ribhan Zafira A.R and Siti Anom.A, Design a PID Controller for a

Constant Speed of Combustion Engine, Australian Journal of Basic and Applied Sciences, 5(12): 1586-1593, 2011 (SCOPUS).

19. M.K. Hassan, R.Z. Abdul Rahman, A,Che Soh, M.Z.Z Ab Kadir, Lightning Strike Mapping for Peninsular

Malaysia Using Artificial Intelligence Techniques. Journal of Theoretical and Applied Information Technology (JATIT) 34(2), 2011, 202-214. (SCOPUS).

20. Mohd.Khair, H and Ishak, .A. The Effect of the Ignition Dwell Time at Constant Speed for CNGDI

Engine, Australian Journal of Basic and Applied Sciences, 4(10): 4691-4694, 2010 (SCOPUS). 21. M.K Hassan, I.Aris, S.Mahmod, R. Sidek , Influence of injection and ignition of CNG fuelled direct

injection engine at constant speed, Australian Journal of Basic Applied Science, 4(10): 4870-4879, 2010, ISSN 1991-8178, 2010. (SCOPUS).

22. M.K Hassan, I.Aris, S.Mahmod, R. Sidek , Influence of injection and ignition of CNG fuelled direct injection engine at constant speed, Australian Journal of Basic Applied Science, ISSN 1991-8178, 2009. (SCOPUS).

23. M.A Kalam, H.H MAsjuki, M Redzuan, T.I. Mahlia, M.A Fuad, M Mohibbah, K.H. Halim, A.Ishak,

M.Khair, A.Shahrir and A.Yusoff. Development and Test of a New Catalytic Converter for Natural Gas Fueled Engine, International journal of Sadhana Acedemy Proceedings in Engineering Science, 560-580, 2009 – ISI/SCI (SCOPUS).

24. Mohd.Khair Hassan, Ishak Aris, Khairul Nizam Zainuddin and Nik Anis Alina, Torque and Power of

CNGDI Engine with Two Different Piston Crown Shapes, Journal of Applied Sciences Research 5(8): 949-954, 2009.

25. M.K Hassan, I.Aris, S.Mahmod, R. Sidek An experimental result of exhaust emission concentration

relative to various injection timing of CNG fuelled direct injection engine. European Journal of Scientific Research, ISSN 1450-216X Vol.25 No.3 (2009), pp.405-416.

26. Wan Zuha A.H.,Zulkifli A.R., Samsul B.M.N, M.Khair H., Liakot A. and Syed A.R, Doppler Effect Method

For Speed Trap Detector. Journal of Industrial Technology Vol.14 (2) 2005, 97-111. 27. M.K Hassan, A. Mustaffa and Norhayati , A Comphehensive GUI with MATLAB Based for Classical,

Modern and Electric Circuit Analysis, Engineering Transactions, Mahanakorn University of Technology, Vol 7, No 1(16), Jan-June 2004, 57-75.

28. Azura Che Soh, Mohd Khair Hassan, Mohd Amran Mohd Radzi and Li Hong Fay, Development Of

Fuzzy Logic Controller For Movement Control Of Robotic System, Journal of Industrial Technology Vol.14 (2) 2005, 113-137.

Updated on 11.9.2014

29. I Aris, M.K. Hassan, I.Mat, K.Nizam,N.A.Alina,R.K.Zakiah,R.Sidek, S.Mahmood, Model-Driven Electronic Control Unit with Real-Time Embedded Target, Engineering Transactions, Mahanakorn University of Technology, Thailand.,Vol.8,No.1(18),Jan-June 2005, 62-80.

30. Ibrahim Mat, Ishak Aris, Mohd Khair, Roslina Mohd. Sidek, , Nik Anis Alina and Syed Malik, Electronic

Control Unit for Vehicles:Issues and the Way Forwards, Journal of Industrial Technology, SIRIM Berhad. Vol.15 (1) 2006, 73-85.

31. Mohd Liakot Ali, Mohd Khair Hassan, Wan Zuha Wan Hasan and Tan Yar Loon, Systhesis of 8-bit

smart Card Microprocessor Using Harvard Architecture and RISC, Journal of Industrial Technology , Vol 14 (1) 2005, 37-58.

Conference Proceedings

1. T. A. T. Mohd, M. K. Hassan, and WMK. A. Aziz, Mathematical Modeling and Simulation of Electric Vehicle using MATLAB-Simulink, International Conference on Automotive Innovation and Green Energy Vehicle (AiGEV 2014), August 26-27, 2014 Kuantan, Pahang, Malaysia.

2. Mohammad Seifi, Azura Che Soh, Mohd Khair Hassan and Noor Izzri Abd. Wahab. An Innovative Demand Side Management for Vulnerable Hybrid Microgrid. 2014 IEEE Innovative Smart Grid Technologies Conference- Asia (ISGT ASIA), 20-23 May 2014, Kuala Lumpur, Malaysia.

3. Maged S.Saeed, Asnor J. Ishak, Siti A.Ahmad, Mohd K. Hassan, Design A Low Cost Electromyography Amplifier Circuit. 1st Mini Symposium on Artificial Intelligence and Robotics, Kuala Lumpur, Malaysia,11 December 2013.

4. M.Azhar Omar, M.Khair Hassan, Azura Che Soh, M.Z.A.Ab.Kadir. Lightning Severity Classification

Utilising the Meteorological Parameters: A Neural Network Approach. 2013 IEEE International conference on Control System, Computing and Engineering, 29 Nov-1 Dec, 2013, Penang Malaysia.

5. Chow Kar Kit, Azura Che Soh, Umi Kalsom Mohammad Yusuf , Asnor Juraiza Ishak,Mohd Khair

Hassan and Shamsul Khamis. E-Nose Herbs Recognition System based on Artificial Neural Network Technique. The 2013 IEEE International Conference on Control System, Computing and Engineering, 29 Nov - 1 Dec 2013, Penang, Malaysia.

6. M.K Hassan, N.Aziah .M.A, Nizam.H.M.I, A.G A Mutalib, S.F Toha, B.S.K.K Ibrahim. A Comparative

Study of Power Consumption of Electric Power Steering System, 180-184, 2012 IEEE International Conference on Power and Energy (PECon), 2-5 December 2012, Kota Kinabalu Sabah.

7. N. Aziah M.A, Nizam H.M.I, S. Ahmad, R.Akmeliawati , S. F. Toha, B.S.K.K. Ibrahim, M.K. Hassan,

Control Strategy of Segregation on HVAC Energy Efficiency as Non Propulsion Electrical Hotel Load in EV , 593-597, , 2012 IEEE International Conference on Power and Energy (PECon), 2-5 December 2012, Kota Kinabalu Sabah.

8. B.S.K.K. Ibrahim, N.A.M. Azubir, N.H.M. Ishak, M.K. Hassan, S.F. Toha, M.A.Z. Abidin, H.F. Ismail and

H. Zamzuri. PI-Fuzzy Logic Control for 3 Phase BLDC Motor for Electric Vehicle Application. Conference of 2012 UKSim-AMSS 6th European Modelling Symposium

9. Mohd Khair Hassan , Ishak Aris, Modeling Brake Torque of CNGDI Engine Using Two-Stage

Regression Technique. Regional Conference on Automotive Research (ReCAR) 2011, 14-15th December 2011. Kuala Lumpur, Malaysia

10. Mohd Khair Hassan , Ishak Aris, Roslina Sidek and Senan Mahmod Power and torque comparison

FOR CNG and Petrol Using LES software.World Engineering Congress 2010, 2nd – 5th August 2010, Kuching, Sarawak, Malaysia Conference on Engineering and Technology Education.

11. M.K Hassan, I.Aris, S.Mahmod and R. Sidek, Exhaust gas concentration of CNG fuelled direct injection

engine at MBT timing, International Advanced of Technology Congress, 2009, PWTC, Kuala Lumpur, 3-5 November 2009.

Updated on 11.9.2014

12. M.A. Kalam, H.H. Masjuki, M. Redzuan, T.M.I. Mahlia, M. A. Fuad, M. Mohibah, Ku. Halim, A.Ishak and

M.Khair, A.Shahrir and A.Yusoff, Experimental Test of a New Compressed Natural Gas Engine With Direct Injection, SAE paper no. 2009-01-1967, USA.

13. M.A. Kalam, H.H. Masjuki, M. Redzuan, T.M.I. Mahlia, M. A. Fuad, M. Mohibah, Ku. Halim, A.Ishak and

M.Khair, A.Shahrir and A.Yusoff, Development and Test of a New Catalytic Converetr for Natural Gas Fueeld Engine, SAE paper no: 2008-01-1550,USA.

14. M.K Hassan, I.Aris, S.Mahmod, R. Sidek, K.N. Zainuddin, N.A.Alina, H.H Masjuki, M. Redzuan, M.A.Kalam,The Influence of Fuel Injection Timing Towards Exhaust Emissions in Compressed Natural Gas Direct Injection (CNGDI) Engine-An Experimental Study, 3rd Brunei International Conference on Engineering and Technology, BICET2008, 3-4 Nov.2008

15. M.K Hassan, I.Aris, S.Mahmod, R.Sidek, K.N. Zainudin, N.A.Alina, H.H. Masjuki, M.Redzwan, M.A.

Kalam, The Effects of Ignition and Injection Timings On Compressed Natural Gas Direct Injection (CNGDI) Multicylinder Engine, 1st Engineering Conference, Energy and Environment, 27-28 December 2007, Kuching Sarawak.

16. I.Aris, M.K Hassan, S.Mahmod, R.Sidek, K.N. Zainudin, N.A.Alina, H.H. Masjuki, M.Redzwan, M.A.

Kalam, Experimental Test and Simulation of Compressed Natural Gas Direct Injection (CNGDI) Single cylinder Engine, 1st Engineering Conference, Energy and Environment, 27-28 December 2007, Kuching Sarawak.

17. Mohd Khair Hassan, Ishak Aris, Jasronita Jasni, Senan Mahmod, roslina Sidek, Hashim Hizam,

Comparative Study of The Potential of Campro 1.6L Engine Fuelled by Compressed Natural Gas, World Engineering Congress 2007 (WEC 2007), 5-9 August, Penang, Malaysia.

18. Mohd Khair Hassan, Ishak Aris,K.N. Zainuddin, H.H Masjuki , M. Redzuan, M.A.Kalam Performance

Analysis Of 1.6l Campro Engine Using Motec And OEM Engine Control Unit, Proc.of the 2nd International Engineering Convention 2007 (IntEC2007), 9-14 Mac 2007. Jeddah, Arab Saudi.

19. I.Aris, M.K. Hassan, R.Sidek, S.Mahmod, I.Mat, K.N.Zainuddin, N.A.Othman, R.K.Z.Sahbudin. Trend

in Electronic Control Unit Development With Real-Time Embedded Target, Proc. Of the Brunei International Conference of Engineering and Technology (BICET) 2005, Brunei Darussalam, 15-18 August 2005.

20. Mohd Khair Hassan, Ishak Aris, Roslina Sidek, Senan Mahmod, Model-Based Approach with Real

Time Embedded Target for Rapid ECU Development: An Overview, Proceeding of the Jordan International of Electrical and Electronic Engineering Conference (JIEEEC) 2005,15-17 Nov,2005. Amman, Jordan.

21. Khairul Nizam, Mohd Khair Hassan, Ishak Aris, Ibrahim Mat, Nik Anis Alina, Issues and Challenges of

ECU Development, RENTAS Symposium 2004, 24-25 Nov 2004, Faculty. Of Engineering. UPM. 22. Ishak Aris, Maaspaliza Azri, Zainab Hasan, M. K. Hassan, M. Khalid, S. M. Amin and H. A. Cyril,

“Development of Software System for Detecting Defective Symbols on Integrated Circuit Chip with Adjustable Readability Level”, CD Proceeding of the 9th International Conference on Mechatronics Technology (ICMT), Kuala Lumpur, 5-8 December 2005.

23. Azura C. S., M.K. Hassan, Li Hong Fey, Intelligent Movement Control For Robots Using Fuzzy Logic,

International Conference Artificial Intelligence in Engineering and Technology (ICAET 2004), 3-5 Aug. 2004, Sabah ,Malaysia.

24. Mohd Khair Hassan, Khairul Nizam Zainuddin, Development Of Control Strategy Of Ecu For CNG–Di

Engine , CNG-DI and Transmission Workshop, 21-23 Dec 2004, Hotel Equtorial, Melaka.

Updated on 11.9.2014

25. Mohd.Khair Hassan, Ribhan Zafira Abdul Rahman, Norhayati Hamid, Mohd Liakot Ali, Learning Aid for Electric Circuits Analysis with MATLAB based GUI, Proceeding of The Seventh Triennial AEESEAP Conference, Univ.Malaya.8,9 Dec 2003, pp 233.

26. Y.S.E.Ali, SBM Noor, S.M Bashi and M.K Hassan, Microcontroller Performance for DC Motor Speed

Control, National Power and Energy Conference, Equtorial, Bangi.2003 27. Ikmal Arif Abd. Jalal, Mohd Khair Hassan, Mohd Amrallah Mustafa, Smart Lighting Management

System, SCOReD 2003, Palm Garden Renaissance Hotel, Putrajaya. 25-26 August 2003. 28. Y.S.Ettomi, S.B.M.Noor, S.M.Bashi and M.K. Hassan, Microcrontroller Based Adjustable Closed-Loop

DC Motor Speed Controller, SCOReD 2003, Palm Garden Renaissance Hotel, Putrajaya. 25-26 August 2003

29. Zulkifli Abd Rahman, Wan Zuha Wan Hasan, Samsul Bahari, Mohd Khair Hassan, Doppler Effect

Method For Speed Trap Detector, SCOReD 2003, Palm Garden Renaissance Hotel, Putrajaya. 25-26 August 2003.

30. Mohd Khair Hassan, Syed Malik Faizal, EMS Applications and Components. Direct Injection

Technology and EMS Development Workshop, 23/9- 24/9/ 2003, Hotel Residence, Putrajaya, Malaysia 31. Mohd Khair Hassan, Samsul Bahari Mohd Noor, Brian Dyer, Mathematical Model Of Pontoon System,

Proc of World Engineering Congress 2002, 22-24 July 2002, Kuching Sarawak, Malaysia.

Books

1. National Occupational Skills Standard (NOSS), Instrumentation and Control: Level 3 (Contributor) - Department of Skill Development, Ministry of Human Resources, MALAYSIA. 2013

2. National Occupational Skills Standard (NOSS), Automotive Accessories and Customization; Level 3 (Contributor) - Department of Skill Development, Ministry of Human Resources, MALAYSIA. 2014

Research Grants- Principal Investigator

No Project Title Amount (RM) Year Funder

1 Formulation of Hybrid Artificial Intelligence Control of Energy System for Electric Vehicle (EV)

147,000 On-going

2013-15 FRGS,MOSTI

2 Exploration on Hybrid Artificial Intelligence of Model-Based Calibration Engine

63,000 Completed

2011-13 ERGS,MOSTI

3 Parameter Optimizations of CNG Fuelled Direct-Injection Engine Using GT-Suite Simulation Package

30,000

Completed

2009-11 RUGS,UPM

4 Real Time Inverted Pendulum Controllers for SISO and MIMO Analysis

10,000 Completed

2003-04 New Lecturer Scheme,UPM

Research Grants- Co-Researcher

No Project Title Amount (RM) Year Funder

1 Nature-Inspired Parametric Analysis of Driver’s Spinal Response to Steering Vibration Impact for Electric Vehicle Steering System

50,000 On-going

2014-16 RACE-MOE Project

Collaboration with IIUM

2 Development of ECU for MEEGE Multi-fuel Mixer for Green Engine

329,600 On-going

2013-15 GP-IPB,UPM

3 Parametric Modelling and Intelligent Control for Vehicle Electrical Loads (VEL) using Fuzzy logic control and Particle Swarm Optimisation (FLC-PSO)-

50,000 On-going

2012-15 ERGS,MOSTI Project

Collaboration with IIUM

Updated on 11.9.2014

Research Grants- Co-Researcher

4 Formulation of Algorithm to Classify Distinctive Odors Pattern of Aromatic Plant Species using Hybrid Artificial Intelligence Techniques

121,500 On-going

2013-15 FRGS,MOSTI

5 Development of A lifting Equation for Malaysia population

15,000 On-going

2013-15 GP-IPS

6 The First Radio Quiet Zone(RQZ) Map for Radio Astronomy in Malaysia

183,000 2013-14 ANGKASA & MOSTI Project

Collaboration with UM

7 An Intelligent Load Control System for Autonomous Microgrid Based on Solar and Wind energy

14,300 Completed

2012-13 RUGS

8 Development of E-Nose Herbs Recognition System Based on Artificial Intelligence Technique

63,000 On-going

2012-14 RUGS

9 Signal Processing Algorithm Development for Ultrasonic Imaging in In-Vivo Skin Characterization-

94,000 On-going

2012-14 RUGS

10 Development of Signal Emulator and Calibration Tool for Multifuel Electronic Control Unit of a Vehicle Power Train

30,000

Completed

2009-11 RUGS

11 ROBOCON 2005 150,000

Completed

2005 UPM

12 Design and Construction of eye-safe laser range finder/speed detector using 1550mm fiber laser.

146,500 Completed

2002-04 IRPA

13 Development of Hybrid-Control for Dynamic System- 117,000 Completed

2002-04 IRPA

14 CNG/DI Engine and Transmission: Development of Electronic Control Unit and Its Diagnostic Kit

2,935,648 Completed

2002-07 IRPA

Patent

Title Reference 1. Ishak Aris, Khairul Nizam, Nik Anis Alina and Mohd Khair Hassan: Method for

Controlling Multiple-injection of Gaseous Fuel in a Direct Injection Engine.

PI20054808, 2005

Copyright

1. Mohd Khair Hassan, Muhammad Azhar Omar, Azura Che soh and Mohd Zainal Abidin Ab Kadir.

Lightning Severity Classification v.1.0- Copyrighted 18/8/2014, Malaysia Copyright Act 1987.

Awards/Recognition

Name of awards

Title Award Authority Award Type Year

1 2.

Silver Medal Excellent in Service

Hardware-in-Loop (HiL) of Fault Detection for Air-Fuel Ratio Control Principal Investigator

EYReC recognised as Malaysia Invention & Design Society (MINDS) at International Engineering Invention and Innovation Exhibition (i-ENVEX). April11th -13th 2014: Universiti Malaysia Perlis Universti Putra Malaysia

International 2014 2014

3. Excellent in Teaching

Excellent in Teaching Faculty of Engineering University 2013, 2012 2011, 2010, 2009, 2004

Updated on 11.9.2014

Awards/Recognition

4. Gold Medal Electronic Control Unit (ECU) for Compressed Natural Gas Direct Injection (CNGDI) Vehicle Researcher

Malaysia Technology Expo 2008, 21-23 February 2008.

National 2008

5. Gold Medal Software system for detecting defective symbols on microchip with adjustable readability level. Researcher

International Exhibition of Ideas-Inventions-New Products (IENA) 2007, Nuremberg, Germany, 1st.

– 4th November, 2007.

International 2007

6 Gold Medal Software System for Detecting Defective Symbols on Micro Chip with Adjustable Readability Level Researcher

18th International Invention, Innovation & Technology Exhibition (ITEX 2007), 18-20 May 2007 Kuala Lumpur, Malaysia.

International 2007

7 Silver Medal

New Electronic Control Unit Control Strategy for Compressed Natural as Direct Injection Vehicle- Researcher

Pameran Rekacipta dan,Penyelidikan dan Inovasi, UPM

Universiti 2007

8 Special Awards from Russian Government,

Software System for Detecting Defective Symbols on Micro Chip with Adjustable 7 Readability Level. Researcher

18th International Invention, and Innovation & Technology Exhibition (ITEX 2007), 18-20 May 2007 Kuala Lumpur, Malaysia.

International 2007

9 Bronze Medal

Software System for Detecting Defective Symbols on Micro Chip with Adjustable Readability Level: Researcher

Pameran Rekacipta dan,Penyelidikan dan Inovasi, UPM

Universiti 2006

10 Gold Medal Compressed Natural Gas Direct Injection Vehicle (CNGDI) Researcher

17th International Invention, Innovation, Industrial Design and Technology Exhibition (ITEX 06), 19-21 May 2006 Kuala Lumpur, Malaysia.

International 2006

13 Best Design

ROBOCON Researcher National ROBOT Competition 2005, 22-23 April 2005, MOHE ROBOCON 2005

National 2005

Updated on 11.9.2014

Consultancy

No Year Title Authority Amount

1 2014 Hardware-in-loop (Hil) for control system development : commissioning and applications– Technical Consultant

EZ Solution Enterprise. Technical seminar conducted for UPNM lecturers

1000

2 2013 Development of Curriculum (COCU) Level 4 for Instrumentation and Control System- Expert Consultant

Adimega Sdn Bhd- appointed consultant company by Ministry of Human Resources, Malaysia for the development of COCU Level 3 Instrument and control System

2,400

3 Nov, 2013

CNGDI Engine- ECU operation and recalibration- Technical Consultant

Hakita Engineering Sdn Bhd 6000

4 2010 ECU and harness development -Technical Consultant

CAR (Centre for Automotive Research), Faculty of Engineering and Built Environment, The National University of Malaysia

800/session

Professional Services

No Title Authority/Funding Designation

1 Malaysian Qualifications Agency (MQA) panel

Panel

2 Creativity & Innovative Technology Competition- CITEC Exhibition 2014

Manpower Department, Ministry of Human Resources, Malaysia

Judge

3 National Occupational Skills Standard (NOSS), NOSS- Instrumentation Control System- Level 3, 4 and 5 ,2013

National Occupational Skills Standard (NOSS), Department of Skill Development, Ministry of Human Resources, Malaysia

Expert Panel

4 Special Project: Hardware in Loop Research Program- 2012

Proton Shah Alam, Research Department

Expert panel

5 Stakeholders Engagement for Planning and Setting Direction of Green Technology Master Plan Preparation-2012

Ministry of Energy, Green Technology and Water (KeTTHA) and Malaysian Green Technology Corporation (GreenTech Malaysia).

Facilitator

6 Bachelor of Technology (Hons) in Applied Automotive program, Department of Mechanical and Automotive Engineering (2011-2013)

Kuala Lumpur International University College (KLIUC)

Industrial Stake Holder

7 Engineering Industrial Training (EIT) Workshop- 2013

Kulliyah of Engineering, International Islamic University (IIUM)

Invited Speaker

8 Starting School, for Semester 1 2013/2014, Pusat Kokurikulum Pembangunan Pelajar (PKPP) 2013

Universiti Putra Malaysia Facilitator

9 Bachelor of Electrical and Electronic Engineering

Department of Electrical and Electronic Engineering, Universiti Putra Malaysia; 2008–13

Program Evaluator

10 Green Technology Challenge.2013 Schneider Electric Malaysia University Challenge-

Proposal evaluator

Updated on 11.9.2014

Professional Services

No Title Authority/Funding Designation

11 Organising Committee Asian International Conference

Asian Control Conference 2015 (ASCC2015)

Technical programme

12 Modelling and simulation using MATLAB Faculty of Engineering, 7-8 May 2003

Facilitator

13 1. American Journal of Modeling and Optimization

2. Journal of Automation and Control Engineering

3. Progress in Intelligent Computing and Applications

4. International Journal of Electronics and Electrical Engineering (IJEEE)

(http://www.sciepub.com/journal/AJMO). :ISSN (Print): 2333-1143 (www.aicit.org/jace/home/editorial.html). ISSN : 2287-6529 www.humanpub.org/pica/home/editorial.html) ISSN: 2287-4844 http://www.ripublication.com/irph/ijeee.htm ISSN: 2301-380X

Editorial Committee

Editorial

Committee

Editorial Committee

Editorial Committee

14 1. Science Fund Proposal: UTM0005505.

Ministry of Higher Education, 2012

Evaluator

15 1. 2014 IEEE Innovative Smart Grid Technologies Conference - Asia (ISGT ASIA) (ISGT14).

Malaysia

Reviewer

16 1. ICCSCE 2013 : 2013 International Conference on Control System, Computing and Engineering, Penang Malaysia

2. Asia Conference on Mechanical and Materials Engineering (ACMME 2013).Wuhan, China, Oct 8-9,2013.

3. The 3rd IEEE International Conference on Computer, Control & Communication (IEEE-IC4 )- Pakistan 25-26 Sept 2013

4. CMAME 2013 - International Conference on Mechanical, Automotive and Materials Engineering (CMAME 2013)- Hong Kong

5. IEEE Business Engineering and Industrial Applications Colloquium 2013 (IEEE BEIAC 2013)-Malaysia

Malaysia

China

Pakistan

Hong Kong

Malaysia

Reviewer

Reviewer

Reviewer

Reviewer

Reviewer

17 1. IEEE International Conference on Power and Energy, 2-5 Dec 2012.

2. International Conference on Agricultural, Food and Biological Engineering, 2012

3. The 2nd International Symposium on Mechanical Science and Technology (ISMST 2011), 20-21 Dec Guangzhou, China

Malaysia

Malaysia

China

Reviewer

Reviewer

Reviewer

18 1. Colloquium on Humanities, Science & Engineering Research (IEEE 2011)

Malaysia

Reviewer

Updated on 11.9.2014

Professional Services

No Title Authority/Funding Designation

19 1. The Asia-Pacific Symposium on Applied Electromagnetic and Mechanics. (2010)

2. World Engineering Congress (WEC 2010)

Malaysia

Malaysia

Reviewer

Reviewer

20 Editorial Committee for Society Automotive Engineering (SAE) conference International Conference on Sustainable Mobility 2010.

Malaysia

Chairperson

21 1. Asia Pacific Conference on Defence & Security Technology (DSTC 2009).

Malaysia

Reviewer

Student Supervision - PhD

Main Supervisor

No. Name Title Status 1. Tengku Azman Tengku

Mohd (GS37906) Development of Hybrid Artificial Intellignce for Energy Management of EV

Ongoing

Co-Supervisor

No. Name Title Status 1. Mohammed Ahmed

(GS38414) Parabolic Dish Antenna Control On going

2. Norhafeezah Kamarudin Development of Lifting Model for Malaysia Population On going

3. Ahmed Hassan Mohamed-GS32088

Collision Prediction based Reinforcement Learning for mobile robot navigation in dynamic environment

Submitted

Co-Supervisor- other universities

No. Name Title University 1. Mohd Kamal Hat

(GE130114) - ongoing Hybrid Algorithm for Traction Motor Control of EV

Universiti Tun Hussein Onn Malaysia

Student Supervision – Master

Main Supervisor

No. Name Title Status

1. Azhar Omar (GS32225)

Lightning Severity Classification Utilizing the Meteorological Parameters: A Neural Network Approach

Graduated

2. Ameer M.F Sider (GS34664)

Development of Brake by Wire (BBW) System for Electric Vehicle- power reduction

Graduated

3 Mohd Hafiz Bin Mohd Nordin

Development of fault detection system of air-fuel ratio control using HiL

On- going

4. Adel Amiri Bahmanshiri (GS34284)

Development of electric power assistant steering system ( EPAS ) for electric vehicle-power reduction

Submitted

5. Hussein Taleghani (GS39533)

Development of energy management system for Electric Vehicle

On going

Updated on 11.9.2014

No. Name Title Status

6. Wan Mohd Khidhir Abdul Aziz (GS37379)

CAN communication for Electric vehicle control panel On going

7. Malathi Naidu A/P Chandran (GS32398)

Development of intelligent Water treatment control for Indah Water

On going

8. Abdul Rahman Abdul Kareem Sattoori Al-Shanoon (GS39676)

Development of precise control of Medical instrument controller with PIC

On going

Co-Supervisor

No. Name Title Status

1. Mohammad Seifi (GS31812)

Design, Modeling And Simulation of Hybrid Microgrid with Smart Demand Side Management

Graduated

2. Ahmed Abdulelah (GS34940)

Develop a Real-Time Tuning Algorithm for Inaccurate Model Using Modified Hill Climbing Approach

Graduated

3. Umi Kalsom Bt Mohamad Yusof (GS36373)

Development of E-Nose Herbs Recognition System Based on Artificial Intelligence Technique

On going

4. Balbir Shah @ Mohd Faddullah

Comparative Performance of On-Off, PID and Fuzzy Logic Controllers pH Process in Boiler Application

Graduated

5. Ahmad Abdusalam Firjani A Web-Based Control and Monitoring System Graduated 6. Yousef A. Ettomi Ali Development of a Micro-controller Based Closed Loop

Speed Control System of DC Motor. Graduated

7. Maspaliza Bte Azri Design and Development of a Fault Detection System for symbol Printedon Integrated Circuit Chip by Matrox

Graduated

Co-Supervisor- other universities

No. Name Title University

1. Nor Aziah Mohd Azubir- ongoing

Development of State Flow Algorithm for Power Consumption of EV

Universiti Teknologi Malaysia, CAIRO, Kuala Lumpur

2. Rabiatul Adawiyah Abu Hanifah ongoing

Design and Development of Intelligent Electric Power Assist Steering (EPAS) System for Electric Vehicle.

Dept of Mechatronic Engineering, Kulliyah of Engineering, IIUM