101
Fasteners
ALASKA INDUSTRIAL HARDWARE, INC.
AIH Order Desk(907) 276-72011-800-478-7201www. .com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
FASTENERS
Page 104
Page 113
Page 120
Page 110 Page 112
Page 117 Page 118
Page 128 Page 130
Chap03 - Fasteners.indd 101 12/29/14 1:07 PM
102
Fasteners
GHD Order Desk(907) 279-66911-800-478-4393
2192 VIKING DRIVEANCHORAGE, AK 99501
GENERAL HARDWAREDISTRUBUTORSwww.ghdalaska.com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Common NailsBright
Popular all-purpose nail, used for general construction, carpentry and framing. Flat head, diamond point and bright finish. Length is from point to underside of head.
Mfg. No. Order No. Size Pkg. Qty.6C1 NLS13145 6d 1 Lb. box8C1 NLS13166 8d 1 Lb. box8C5 NLS13169 8d 5 Lb. box8D BRIGHT NLS13175 8d 50 Lb. box10C1 NLS13178 10d 1 Lb. box10C5 NLS13181 10d 5 Lb. box16C1 NLS13202 16d 1 Lb. box16C5 NLS13205 16d 5 Lb. box16D BRIGHT NLS13211 16d 50 Lb. box20C1 NLS13214 20d 1 Lb. box20C5 NLS13217 20d 5 Lb. box60D BRIGHT NLS13259 60d 50 Lb. box
Common NailsGalvanized
An all-purpose nail for outdoor use, coated to ease penetration and improve holding power. Recommended for cedar or redwood.
Mfg. No. Order No. Size Pkg. Qty.6HGC1 NLS13306 6d 1 Lb. box6HGC NLS13315 6d 50 Lb. box8HGC1 NLS13321 8d 1 Lb. box8HGC5 NLS13324 8d 5 Lb. box8HGC NLS13330 8d 50 Lb. box16HGC1 NLS13357 16d 1 Lb. box16HGC5 NLS13360 16d 5 Lb. box16HGC NLS13366 16d 50 Lb. box
Concrete Nails
Fluted shank masonry/concrete nails for use on concrete forms.
Mfg. No. Order No. Lgth. In. Pkg. Qty.212TFMAS1 NLS17449 2-1/2 1 Lb. box212TFMAS5 NLS17452 2-1/2 5 Lb. box
Box NailsGalvanized
With a thin shank designed to reduce split-ting. Good choice for fencing projects and recommended for cedar and redwood.
Mfg. No. Order No. Size Pkg. Qty.6HGBX1 NLS12362 6d 1 Lb. box6HGBX5 NLS12365 6d 5 Lb. box8HGBX1 NLS12386 8d 1 Lb. box8HGBX5 NLS12389 8d 5 Lb. box8HGBX NLS12395 8d 50 Lb. box10HGBX1 NLS12398 10d 1 Lb. box10HGBX5 NLS12401 10d 5 Lb. box16HGBX1 NLS12422 16d 1 Lb. box16HGBX5 NLS12425 16d 5 Lb. box16HGBX NLS12431 16d 50 Lb. box20HGBX1 NLS12434 20d 1 Lb. box20HGBX5 NLS12437 20d 5 Lb. box20HGBX NLS12443 20d 50 Lb. box
Finish Nails
Thin nail used for finishing work. Brad head cupped for easy concealment. With bright finish.Mfg. No. Order No. Size Pkg. Qty.
Bright6F1 NLS14359 6d 1 Lb. box6F5 NLS14362 6d 5 Lb. box8F1 NLS14374 8d 1 Lb. box8F5 NLS14377 8d 5 Lb. box
Galvanized6HGF1 NLS14472 6d 1 Lb. box8HGF1 NLS14484 8d 1 Lb. box
2015 Catalog.indb 102 12/26/14 10:49 AM
103
Fasteners
ALASKA INDUSTRIAL HARDWARE, INC.
AIH Order Desk(907) 276-72011-800-478-7201www. .com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Roofing NailsGalvanized
NLS16464
NLS16647
Features large head for greater holding, sharp point and thin shank for easy penetra-tion. Recommended for cedar or redwood.
Mfg. No. Order No. Lgth. In. Pkg. Qty.114EGRFG1 NLS16464 1-1/4 1 Lb. box114EGRFG5 NLS16467 1-1/4 5 Lb. box112EGRFG1 NLS16476 1-1/2 1 Lb. box112EGRFG5 NLS16479 1-1/2 5 Lb. box112EGRFG NLS16485 1-1/2 50 Lb. box2EGRFG1 NLS16500 2 1 Lb. box2EGRFG5 NLS16503 2 5 Lb. box
With Neoprene Washer134EGNEO5 NLS16647 1-3/4 5 Lb. box
Duplex Nails
With two heads. First head for holding strength, second positioned for easy re-moval with claw or crowbar. For temporary construction applications such as forms or scaffolding.
Mfg. No. Order No. Size Pkg. Qty.8DUP1 NLS13865 8d 1 Lb. box8DUP5 NLS13868 8d 5 Lb. box8D NLS50710 8d 50 Lb. box16DUP1 NLS13901 16d 1 Lb. box16DUP5 NLS13904 16d 5 Lb. box16D NLS50695 16d 50 Lb. box
Joist Hanger NailsGalvanized
For attaching joist hangers to wood studs. Short, heavy gauge nail provides increased holding power without fully penetrating wood.
Mfg. No. Order No. Lgth. In. Pkg. Qty.112HGJST1 NLS14800 1-1/2 1 Lb. box112HGJST5 NLS14803 1-1/2 5 Lb. box
Sinker NailsVinyl Coated
Used primarily as a framing nail. Counter-sunk head provides flat, even surface with wood. Coated to ease penetration and in-crease holding power.
Mfg. No. Order No. Size Pkg. Qty.8CTDSKR1 NLS15628 8d 1 Lb. box8CTDSKR5 NLS15631 8d 5 Lb. box8D/VC NLS50675 8d 50 Lb. box16CTDSKR1 NLS15664 16d 1 Lb. box16CTDSKR5 NLS15667 16d 5 Lb. box16D/VC NLS50650 16d 50 Lb. box
Casing NailsGalvanized
Coated with zinc for excellent rust resis-tance. Cupped brad heads for easy conceal-ment. Recommended for use with cedar or redwood.
Mfg. No. Order No. Size Pkg. Qty.16HGCAS 1# NLS12950 16d 1 Lb. box16HGCAS5 NLS12953 16d 5 Lb. box
Spikes
Spike
Galvanized Spike
For extra holding power on large pieces of wood.
Mfg.No.
OrderNo.
Lgth.In.
Dia.In.
Pkg.Qty.
8SPK NLS14832 8 3/8 50 Lb. box10SPK NLS14838 10 3/8 50 Lb. box12SPK NLS14844 12 3/8 50 Lb. box
Galvanized8HGSPK NLS14949 8 3/8 50 Lb. box10HGSPK NLS14955 10 3/8 50 Lb. box12HGSPK NLS14961 12 3/8 50 Lb. box
Galvanized Staples
For installation of wire fencing or nailing. Made from bent wire with points on both ends. Recommended for cedar or redwood.
Mfg. No. Order No. Lgth. In. Pkg. Qty.112HGFS5 NLS14195 1-1/2 5 Lb. box
Storage SystemsDrawers
Heavy duty steel construction. Drawers have 24 compartments, a locking mechanism, handle and can be removed from the cabi-net. Includes over 2000 assorted pieces of premium grade hardware, grade 5 SAE and grade 8.8 metric nuts and bolts.
Mfg. No.
OrderNo.
No. Drawers
Dim. In.L x W x H
90-800 OLY90800 4 18.7 x 15.8 x 13.5
Screw AssortmentsStainless Steel
Most common sizes of flat & pan head screws nuts & washers. Includes plastic case.
Mfg. No. Order No. Pc. Qty.01000-0001-800 PFC21622 520
Fastener AssortmentsStainless Steel
Includes round head slotted screws, flat washers, machine screws, and nuts.
Mfg. No. Order No. Pc. Qty.W5358 WIM15989 224
2015 Catalog.indb 103 12/26/14 10:49 AM
104
Fasteners
GHD Order Desk(907) 279-66911-800-478-4393
2192 VIKING DRIVEANCHORAGE, AK 99501
GENERAL HARDWAREDISTRUBUTORSwww.ghdalaska.com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Hex BoltsGrade 2
Grade 2 Grade 2 fasteners are typically made of low-carbon steel and are com-monly used for wood and general hardware applications where higher strength is not required. They have no radial markings on the head. Zinc Plating helps to prevent cor-rosion. Hex bolts have a chamfered point to aid insertion into a tapped hole or nut. Length is measured from under the head.
SizeIn.
Proof LoadPSI
Min. Tensile Strength PSI
1/4 – 3/4 55,000 74,000Over 3/4 33,000 60,000
Hex BoltsZinc-Plated
NC Grade 2.
OrderNo.
Lgth.In.
Pkg.Qty.
1/4" Diameter2ZP1434 3/4 1002ZP141 1 1002ZP14114 1-1/4 1002ZP14112 1-1/2 1002ZP14134 1-3/4 1002ZP142 2 1002ZP14212 2-1/2 1002ZP143 3 1002ZP14312 3-1/2 1002ZP144 4 1002ZP145 5 1002ZP146 6 100
5/16" Diameter2ZP51634 3/4 1002ZP5161 1 1002ZP516114 1-1/4 1002ZP516112 1-1/2 1002ZP516134 1-3/4 1002ZP5162 2 1002ZP516212 2-1/2 1002ZP5163 3 1002ZP516312 3-1/2 502ZP5164 4 502ZP516412 4-1/2 502ZP5165 5 502ZP5166 6 50
3/8" Diameter2ZP3834 3/4 1002ZP381 1 100
2ZP38114 1-1/4 1002ZP38112 1-1/2 1002ZP38134 1-3/4 1002ZP382 2 1002ZP38212 2-1/2 502ZP383 3 502ZP38312 3-1/2 502ZP384 4 502ZP38412 4-1/2 502ZP385 5 502ZP38512 5-1/2 502ZP386 6 502ZP387 7 502ZP388 8 502ZP389 9 502ZP3810 10 50
1/2" Diameter2ZP121 1 502ZP12114 1-1/4 502ZP12112 1-1/2 502ZP12134 1-3/4 502ZP122 2 502ZP12212 2-1/2 502ZP123 3 502ZP12312 3-1/2 252ZP124 4 252ZP12412 4-1/2 252ZP125 5 252ZP12512 5-1/2 252ZP126 6 252ZP127 7 252ZP128 8 252ZP129 9 252ZP1210 10 252ZP1212 12 25
5/8" Diameter2ZP58112 1-1/2 252ZP582 2 252ZP58212 2-1/2 252ZP583 3 252ZP58312 3-1/2 252ZP584 4 252ZP585 5 252ZP586 6 252ZP587 7 252ZP588 8 252ZP589 9 202ZP5810 10 202ZP5812 12 20
3/4" Diameter2ZP342 2 202ZP34212 2-1/2 202ZP343 3 202ZP34312 3-1/2 202ZP344 4 202ZP345 5 202ZP346 6 202ZP347 7 202ZP348 8 202ZP3410 10 202ZP3412 12 15
Hex BoltsGalvanized
NC Grade 2.
OrderNo.
Lgth.In.
Pkg.Qty.
1/4" DiameterHGB141 1 100HGB14112 1-1/2 100HGB142 2 100HGB14212 2-1/2 100HGB143 3 100HGB14312 3-1/2 100HGB144 4 100HGB145 5 100HGB146 6 100
5/16" DiameterHGB5161 1 100HGB516112 1-1/2 100HGB5162 2 100HGB516212 2-1/2 100HGB5163 3 100HGB516312 3-1/2 50HGB5164 4 50HGB5165 5 50HGB5166 6 50
3/8" DiameterHGB381 1 100HGB38112 1-1/2 100HGB382 2 100HGB38212 2-1/2 50HGB383 3 50HGB38312 3-1/2 50HGB384 4 50HGB38412 4-1/2 50HGB385 5 50HGB386 6 50
1/2" DiameterHGB121 1 50HGB12112 1-1/2 50HGB122 2 50HGB12212 2-1/2 50HGB123 3 50HGB12312 3-1/2 25HGB124 4 25HGB12412 4-1/2 25HGB125 5 25HGB126 6 25HGB127 7 25
5/8" DiameterHGB582 2 25HGB58212 2-1/2 25HGB583 3 25HGB584 4 25HGB585 5 25HGB586 6 25
3/4" DiameterHGB34212 2-1/2 20HGB343 3 20HGB34312 3-1/2 20HGB344 4 20HGB345 5 20HGB346 6 20HGB348 8 20
2015 Catalog.indb 104 12/26/14 10:49 AM
105
Fasteners
ALASKA INDUSTRIAL HARDWARE, INC.
AIH Order Desk(907) 276-72011-800-478-7201www. .com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Hex BoltsGrade 8
Grade 8 Grade 8 bolts are comprised of car-bon alloy steel, heat treated in a carbon con-trolled atmosphere and are generally the most durable and reliable fastener. Higher grade materials, such as carbon alloy steel, allow for greater torque strength in the threads of the bolt. The preload, or thread tension in a fastener is higher when the type of steel being used is grade 8 in quality.
SizeIn.
Proof LoadPSI
Min. Tensile Strength PSI
1/4 – 1 120,000 150,000
Hex BoltsZinc-Plated — Coarse Thread
NC Grade 8.
OrderNo.
Lgth.In.
Pkg.Qty.
1/4" Diameter8NC1412 1/2 1008NC1434 3/4 1008NC141 1 1008NC14114 1-1/4 1008NC14112 1-1/2 1008NC14134 1-3/4 1008NC142 2 1008NC14212 2-1/2 1008NC143 3 1008NC14312 3-1/2 1008NC144 4 100
5/16" Diameter8NC51634 3/4 1008NC5161 1 1008NC516114 1-1/4 1008NC516112 1-1/2 1008NC516134 1-3/4 1008NC5162 2 1008NC516212 2-1/2 1008NC5163 3 1008NC516312 3-1/2 508NC5164 4 508NC5165 5 508NC5166 6 50
3/8" Diameter8NC3834 3/4 1008NC381 1 1008NC38114 1-1/4 1008NC38112 1-1/2 1008NC38134 1-3/4 1008NC382 2 1008NC38212 2-1/2 508NC38234 2-3/4 508NC383 3 508NC38312 3-1/2 508NC384 4 508NC38412 4-1/2 508NC385 5 508NC386 6 50
7/16" Diameter8NC7161 1 1008NC716114 1-1/4 508NC716112 1-1/2 508NC716134 1-3/4 508NC7162 2 508NC716212 2-1/2 508NC7163 3 508NC716312 3-1/2 258NC7164 4 258NC7165 5 258NC7166 6 25
1/2" Diameter8NC121 1 508NC12114 1-1/4 50
8NC12112 1-1/2 508NC12134 1-3/4 508NC122 2 508NC12212 2-1/2 50 8NC123 3 508NC12312 3-1/2 258NC124 4 258NC12412 4-1/2 258NC125 5 258NC126 6 25
9/16" Diameter8NC916112 1-1/2 258NC9162 2 258NC916212 2-1/2 258NC9163 3 258NC916312 3-1/2 258NC9164 4 258NC9165 5 258NC9166 6 25
5/8" Diameter8NC58114 1-1/4 258NC58112 1-1/2 258NC58134 1-3/4 258NC582 2 258NC58214 2-1/4 258NC58212 2-1/2 258NC583 3 258NC58312 3-1/2 258NC584 4 258NC58412 4-1/2 258NC585 5 258NC586 6 258NC587 7 258NC588 8 25
3/4" Diameter8NC34112 1-1/2 208NC342 2 208NC34214 2-1/4 208NC34212 2-1/2 208NC34234 2-3/4 208NC343 3 208NC34312 3-1/2 208NC344 4 208NC34412 4-1/2 208NC345 5 208NC346 6 208NC347 7 208NC348 8 20
7/8" Diameter8NC782 2 108NC78212 2-1/2 108NC783 3 108NC78312 3-1/2 108NC784 4 108NC78412 4-1/2 108NC785 5 108NC786 6 10
1" Diameter8NC1212 2-1/2 108NC13 3 108NC1312 3-1/2 108NC14 4 108NC15 5 108NC16 6 108NC17 7 108NC18 8 10
NOTES________________________________________________________________________________________________________________________________________________________________________________________________________________
2015 Catalog.indb 105 12/26/14 10:49 AM
106
Fasteners
GHD Order Desk(907) 279-66911-800-478-4393
2192 VIKING DRIVEANCHORAGE, AK 99501
GENERAL HARDWAREDISTRUBUTORSwww.ghdalaska.com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Hex BoltsZinc-Plated — Fine Thread
NF Grade 8.
OrderNo.
Lgth.In.
Pkg.Qty.
1/4" Diameter8NF1412 1/2 1008NF1434 3/4 1008NF141 1 1008NF14114 1-1/4 1008NF14112 1-1/2 1008NF14134 1-3/4 1008NF142 2 1008NF14212 2-1/2 1008NF143 3 100
5/16" Diameter8NF51634 3/4 1008NF5161 1 1008NF516114 1-1/4 1008NF516112 1-1/2 1008NF516134 1-3/4 1008NF5162 2 1008NF516212 2-1/2 1008NF5163 3 1008NF516312 3-1/2 508NF5164 4 50
3/8" Diameter8NF3834 3/4 1008NF381 1 1008NF38114 1-1/4 1008NF38112 1-1/2 1008NF38134 1-3/4 1008NF382 2 1008NF38212 2-1/2 508NF383 3 508NF38312 3-1/2 508NF384 4 50
1/2" Diameter8NF121 1 508NF12114 1-1/4 508NF12112 1-1/2 508NF12134 1-3/4 508NF122 2 508NF12212 2-1/2 508NF123 3 508NF12312 3-1/2 258NF124 4 258NF12412 4-1/2 258NF125 5 258NF126 6 25
5/8" Diameter8NF58112 1-1/2 258NF582 2 258NF58212 2-1/2 258NF583 3 258NF58312 3-1/2 258NF584 4 25
Hex BoltsStainless Steel
NC Grade 18-8.
OrderNo.
Lgth.in.
Pkg.Qty.
1/4" Diameter
SSB1434 3/4 100
SSB141 1 100
SSB14112 1-1/2 100
SSB142 2 100
SSB14212 2-1/2 100
SSB143 3 100
SSB14312 3-1/2 100
SSB144 4 100
5/16" Diameter
SSB51634 3/4 100
SSB5161 1 100
SSB516112 1-1/2 100
SSB5162 2 100
SSB516212 2-1/2 100
SSB5163 3 100
SSB516312 3-1/2 50
SSB5164 4 50
3/8" Diameter
SSB3834 3/4 100
SSB381 1 100
SSB38112 1-1/2 100
SSB382 2 100
SSB38212 2-1/2 50
SSB383 3 50
SSB38312 3-1/2 50
SSB384 4 50
1/2" Diameter
SSB12112 1-1/2 50
SSB122 2 50
SSB12212 2-1/2 50
SSB123 3 50
SSB12312 3-1/2 25
SSB124 4 25
SSB12412 4-1/2 25
SSB125 5 25
SSB126 6 25
Carriage BoltsZinc-Plated
OrderNo.
Lgth.In.
Pkg.Qty.
3/16" DiameterCAB31634 3/4 100CAB3161 1 100CAB316112 1-1/2 100CAB3162 2 100
1/4" DiameterCAB141 1 100CAB14112 1-1/2 100CAB142 2 100CAB14212 2-1/2 100CAB143 3 100CAB14312 3-1/2 100CAB144 4 100CAB14412 4-1/2 100CAB145 5 100CAB146 6 100
5/16" DiameterCAB5161 1 100CAB516112 1-1/2 100CAB5162 2 100CAB516212 2-1/2 100CAB5163 3 100CAB516312 3-1/2 50CAB5164 4 50CAB516412 4-1/2 50CAB5165 5 50CAB5166 6 50
3/8" DiameterCAB381 1 100CAB38112 1-1/2 100CAB382 2 100CAB38212 2-1/2 50CAB383 3 50CAB38312 3-1/2 50CAB384 4 50CAB38412 4-1/2 50CAB385 5 50CAB38512 5-1/2 50CAB386 6 50CAB387 7 50CAB388 8 50CAB389 9 50CAB3810 10 50
2015 Catalog.indb 106 12/26/14 10:49 AM
107
Fasteners
ALASKA INDUSTRIAL HARDWARE, INC.
AIH Order Desk(907) 276-72011-800-478-7201www. .com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Carriage BoltsZinc-Plated
OrderNo.
Lgth.In.
Pkg.Qty.
1/2" Diameter
CAB12112 1-1/2 50
CAB122 2 50
CAB12212 2-1/2 50
CAB123 3 50
CAB12312 3-1/2 25
CAB124 4 25
CAB12412 4-1/2 25
CAB125 5 25
CAB126 6 25
CAB127 7 25
CAB128 8 25
CAB129 9 25
CAB1210 10 25
CAB1212 12 25
5/8" Diameter
CAB582 2 25
CAB58212 2-1/2 25
CAB583 3 25
CAB58312 3-1/2 25
CAB584 4 25
CAB585 5 25
CAB586 6 25
CAB587 7 25
CAB588 8 25
CAB5810 10 20
CAB5812 12 20
Carriage BoltsGalvanized
OrderNo.
Lgth.In.
Pkg.Qty.
1/4" Diameter
HGC14112 1-1/2 100
HGC142 2 100
HGC14212 2-1/2 100
HGC143 3 100
HGC14312 3-1/2 100
HGC144 4 100
5/16" Diameter
HGC516112 1-1/2 100
HGC5162 2 100
HGC516212 2-1/2 100
HGC5163 3 100
HGC516312 3-1/2 50
HGC5164 4 50
HGC516412 4-1/2 50
HGC5165 5 50
HGC516512 5-1/2 50
HGC5166 6 50
3/8" Diameter
HGC38112 1-1/2 100
HGC382 2 100
HGC38212 2-1/2 50
HGC383 3 50
HGC38312 3-1/2 50
HGC384 4 50
HGC385 5 50
HGC386 6 50
1/2" Diameter
HGC12112 1-1/2 50
HGC122 2 50
HGC12212 2-1/2 50
HGC123 3 50
HGC12312 3-1/2 25
HGC124 4 25
HGC12412 4-1/2 25
HGC125 5 25
HGC126 6 25
Lag ScrewsZinc-Plated
OrderNo.
Lgth.In.
Pkg.Qty.
1/4" DiameterLAG141 1 100LAG14112 1-1/2 100LAG142 2 100LAG14212 2-1/2 100LAG143 3 100LAG14312 3-1/2 100LAG144 4 100LAG14412 4-1/2 100LAG145 5 100LAG146 6 100
5/16" DiameterLAG5161 1 100LAG516112 1-1/2 100LAG5162 2 100LAG516212 2-1/2 100LAG5163 3 100LAG516312 3-1/2 50LAG5164 4 50LAG516412 4-1/2 50LAG5165 5 50LAG5166 6 50
3/8" DiameterLAG381 1 100LAG38112 1-1/2 100LAG382 2 100LAG38212 2-1/2 50LAG383 3 50LAG38312 3-1/2 50LAG384 4 50LAG38412 4-1/2 50LAG385 5 50LAG386 6 50LAG387 7 50LAG388 8 50
1/2" DiameterLAG122 2 50LAG12212 2-1/2 50LAG123 3 50LAG12312 3-1/2 25LAG124 4 25LAG12412 4-1/2 25LAG125 5 25LAG126 6 25LAG127 7 25LAG128 8 25LAG1210 10 25
5/8" DiameterLAG583 3 25LAG584 4 25LAG585 5 25LAG586 6 25LAG588 8 25LAG5810 10 20LAG5812 12 20
3/4" DiameterLAG343 3 20LAG344 4 20LAG345 5 20LAG346 6 20LAG348 8 20
2015 Catalog.indb 107 12/26/14 10:49 AM
108
Fasteners
GHD Order Desk(907) 279-66911-800-478-4393
2192 VIKING DRIVEANCHORAGE, AK 99501
GENERAL HARDWAREDISTRUBUTORSwww.ghdalaska.com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Lag ScrewsGalvanized
OrderNo.
Lgth.In.
Pkg.Qty.
1/4" DiameterHGL14112 1-1/2 100HGL142 2 100HGL14212 2-1/2 100HGL143 3 100HGL144 4 100HGL145 5 100HGL146 6 100
5/16" DiameterHGL516112 1-1/2 100HGL5162 2 100HGL516212 2-1/2 100HGL5163 3 100HGL516312 3-1/2 50HGL5164 4 50HGL516412 4-1/2 50HGL5165 5 50HGL5166 6 50
3/8" DiameterHGL38112 1-1/2 100HGL382 2 100HGL38212 2-1/2 50HGL383 3 50HGL38312 3-1/2 50HGL384 4 50HGL38412 4-1/2 50HGL385 5 50HGL386 6 50
1/2" DiameterHGL12112 1-1/2 50HGL122 2 50HGL12212 2-1/2 50HGL123 3 50HGL12312 3-1/2 25HGL124 4 25HGL125 5 25HGL126 6 25HGL127 7 25HGL128 8 25
5/8" DiameterHGL583 3 25HGL584 4 25HGL585 5 25HGL586 6 25
Lag ScrewsStainless Steel
OrderNo.
Lgth.In.
Pkg.Qty.
1/4" Diameter
SSLG141 1 100
SSLG14114 1-1/4 100
SSLG14112 1-1/2 100
SSLG142 2 100
SSLG14212 2-1/2 100
SSLG143 3 100
SSLG14312 3-1/2 100
SSLG144 4 100
5/16" Diameter
SSLG5161 1 100
SSLG516112 1-1/2 100
SSLG5162 2 100
SSLG516212 2-1/2 100
SSLG5163 3 100
SSLG516312 3-12 50
SSLG5164 4 50
SSLG5165 5 50
3/8" Diameter
SSLG38112 1-1/2 100
SSLG382 2 100
SSLG38212 2-1/2 50
SSLG383 3 50
SSLG384 4 50
SSLG385 5 50
SSLG386 6 50
All ThreadThreaded Rods
Zinc-plated steel.Order
No.Lgth.
In.10-24 Thread Size
ALL102436 361/4" Thread Size
ALL1412 12ALL1436 36ALL1472 72ALL14120 120
5/16" Thread SizeALL51612 12ALL51636 36ALL51672 72
3/8"Thread SizeALL3812 12ALL3836 36ALL3872 72ALL38120 120
7/16" Thread SizeALL71636 36
1/2" Thread SizeALL1212 12ALL1236 36ALL1272 72ALL12120 120
5/8" Thread SizeALL5836 36ALL5872 72ALL58120 120
3/4" Thread SizeALL3436 36ALL3472 72ALL34120 120
7/8" Thread SizeALL7836 36ALL7872 72ALL78120 120
1" Thread SizeALL136 36ALL172 72ALL1120 120
1-1/8" Thread SizeALL118144 144
2015 Catalog.indb 108 12/26/14 10:49 AM
109
Fasteners
ALASKA INDUSTRIAL HARDWARE, INC.
AIH Order Desk(907) 276-72011-800-478-7201www. .com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Rod Couplings
OrderNo.
ThreadSize
Pkg.Qty.
RDC14 1/4"-20 50RDC516 5/16"-18 30RDC38 3/8"-16 30RDC12 1/2"-13 30RDC58 5/8"-11 20RDC34 3/4"-10 20RDC78 7/8" - 9 10RDC1 1 10RDC118 1-1/8" - 7 10
Hanger Bolts
OrderNo.
Lgth.In.
Pkg.Qty.
1/4" DiameterPFC13229 2-1/2 100
3/8" DiameterPFC22290 3 100PFC09792 4 50
Anchor Bolts
Hot-dipped galvanized. Includes nut.
Mfg. No. Order No. Dia. In. Lgth. In.FB5810 KIRAB5810 5/8 10
Acoustical Eye Lags
For use with tie wire, ceiling wire, and jack chain applications.
Order No. Dia. In. Lgth. In. Pkg. Qty.PFCEYELAG 1/4 3 25
Machine Screws
Phillips slot.
OrderNo.
Lgth.In.
ThreadSize
Pkg.Qty.
Flat Head — Stainless SteelPFC12193 3/4 1/4"-20 50PFC12195 1 1/4"-20 50PFC12197 1-1/2 1/4"-20 50PFC12198 2 1/4"-20 25
Pan Head — Stainless SteelPFC12213 1/2 8-32 100PFC12214 3/4 8-32 100PFC12219 1 8-32 100PFC12223 3/4 10-24 100PFC12225 1 10-24 100PFC12227 1-1/2 10-24 50PFC12228 2 10-24 50PFC12229 1/2 1/4"-20 100PFC12231 1 1/4"-20 50PFC12233 1-1/2 1/4"-20 50PFC12235 2 1/4"-20 25
Flat Head — ZincPFC13183 1/2 6-32 100PFC13186 3/4 6-32 100PFC13188 1 6-32 100PFC13190 1-1/2 6-32 100PFC13218 2 6-32 100PFC13219 1/2 8-32 100PFC13222 3/4 8-32 100PFC13223 1 8-32 100PFC13224 1-1/2 8-32 100PFC13225 2 8-32 50PFC13226 2-1/2 8-32 100PFC13227 3 8-32 100PFC13232 1/2 10-24 100PFC13240 3/4 10-24 100PFC13241 1 10-24 100PFC13242 1-1/4 10-24 100PFC13243 1-1/2 10-24 50PFC13258 2 10-24 50PFC13262 3 10-24 50PFC13264 1/2 1/4"-20 100PFC13267 3/4 1/4"-20 50PFC13268 1 1/4"-20 50PFC13269 1-1/2 1/4"-20 50PFC13272 2-1/2 1/4"-20 25PFC13273 2 1/4"-20 25PFC13274 3 1/4"-20 25PFC13276 4 1/4"-20 25
Machine ScrewsRound Head — Phillips
Round head with Phillips slot. Zinc.Order
No.Lgth.
In. Thread SizePkg. Qty.
PFC13098 1/2 8-32 100
PFC13102 3/4 8-32 100
PFC47233 1 8-32 100
PFC13111 1-1/2 8-32 50
PFC13113 2 8-32 50
PFC13119 2-1/2 8-32 50
PFC13122 3 8-32 50
PFC13124 1/2 10-24 100
PFC13125 3/4 10-24 100
PFC13126 1 10-24 100
PFC13127 1-1/4 10-24 100
PFC13128 1-1/2 10-24 50
PFC13129 2 10-24 50
PFC13130 3 10-24 50
PFC13132 1/2 10-32 100
PFC13135 3/4 10-32 100
PFC13138 1 10-32 100
PFC13140 1-1/2 10-32 50
PFC13142 2 10-32 50
PFC13146 1/4 1/4-20 100
PFC13154 3/4 1/4-20 50
PFC13159 1 1/4-20 50
PFC13165 1-1/4 1/4-20 50
PFC13169 1-1/2 1/4-20 50
PFC13175 2 1/4-20 25
PFC13176 2-1/2 1/4-20 25
PFC13177 3 1/4-20 25
PFC13178 4 1/4-20 25
2015 Catalog.indb 109 12/26/14 10:49 AM
110
Fasteners
GHD Order Desk(907) 279-66911-800-478-4393
2192 VIKING DRIVEANCHORAGE, AK 99501
GENERAL HARDWAREDISTRUBUTORSwww.ghdalaska.com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Hex Nuts
Order No. Thread Size Pkg. Qty.Zinc Plated
NZP1420 1/4"-20 100NZP51618 5/16"-18 100NZP3816 3/8"-16 100NZP71614 7/16"-14 50NZP1213 1/2"-13 50NZP5811 5/8"-11 25NZP3410 3/4"-10 20NZP789 7/8"-9 15NZP18 1"-8 10NZP1187 1-1/8"-7 10NZP1147 1-1/4"-7 10
Stainless SteelSSN1420 1/4"-20 100SSN51618 5/16"-18 50SSN3816 3/8"-16 50SSN1213 1/2"-13 50SSN5811 5/8"-11 25
Hex Nuts
Galvanized.
Order No. Thread Size Pkg. Qty.HGN1420 1/4"-20 NC 100HGN51618 5/16"-18 NC 100HGN3816 3/8"-16 NC 100HGN1213 1/2"-13 NC 50HGN5811 5/8"-11 NC 25HGN3410 3/4"-10 NC 20HGN789 7/8"-9 NC 15
Machine Screw Nuts
Order No. Thread Size Pkg. Qty.PFC72665 6-32 100PFC72666 8-32 100PFC72667 10-24 100PFC72672 10-32 100PFC13047 12-24 100PFC72669 1/4"-20 100
Stainless SteelPFC14906 6-32 100PFC14908 8-32 100PFC12107 10-24 100PFC12104 1/4-20 100
Hex Nuts
Grade 8.Order No. Thread Size Pkg. Qty.
8NT1420 1/4"-20 NC 1008NT1428 1/4"-28 NF 1008NT51618 5/16"-18 NC 1008NT51624 5/16"-24 NF 1008NT3816 3/8"-16 NC 1008NT3824 3/8"-24 NF 1008NT71614 7/16"-14 NC 508NT1213 1/2"-13 NC 508NT1220 1/2"-20 NF 508NT91612 9/16"-12 NC 258NT5811 5/8"-11 NC 258NT5818 5/8"-18 NF 258NT3410 3/4"-10 NC 208NT789 7/8"-9 NC 158NT18 1"-8 NC 10
LocknutsNylon
Order No. Thread Size Pkg. Qty.NLN1024 10/24 NC 100NLN1032 10/32 NF 100NLN1420 1/4"-20 NC 100NLN1428 1/4"-28 NF 100NLN51618 5/16"-18 NC 100NLN51624 5/16"-24 NF 100NLN3816 3/8"-16 NC 100NLN3824 3/8"-24 NF 100NLN71614 7/16"-14 NC 100NLN1213 1/2"-13 NC 100NLN1220 1/2"-20 NF 100NLN91612 9/16"-12 NC 50NLN5811 5/8"-11 NC 50NLN5818 5/8"-18 NF 50NLN3410 3/4"-10 NC 50NLN789 7/8"-9 NC 25NLN18 1"-8 NC 25
Stainless SteelPFC14910 6-32 SS 100PFC12120 8-32 SS 100PFC12122 10-24 SS 100PFC12127 1/4-20 SS 100SSLN1420 1/4"-20 100SSLN51618 5/16"-18 100SSLN3816 3/8"-16 50SSLN1213 1/2"-13 25
Grade 88LN1420 1/4"-20 GR8 1008LN51618 5/16"-18 GR8 1008LN3816 3/8"-16 GR8 1008LN71614 7/16"-14 GR8 1008LN1213 1/2"-13 GR8 1008LN91612 9/16"-12 GR8 508LN3410 3/4"-10 GR8 508LN5811 5/8"-11 GR8 50
Wingnuts
Zinc-plated.
Order No. Thread Size Pkg. Qty.PFC72823 10-24 100PFC72824 1/4"-20 50PFC72825 5/16"-18 50PFC72826 3/8"-16 25PFC72827 1/2"-13 10
WashersSAE
Zinc-plated.
Order No. Trade Size Pkg. Qty.PFC72971 #6 100PFC72972 #8 100PFC72973 #10 100PFC30300 #12 100PFC30301 1/4 100PFC30302 5/16 100PFC30303 3/8 100PFC30304 7/16 105PFC30305 1/2 55PFC92980 9/16 43PFC92981 5/8 36PFC92982 3/4 21
Cut WashersZinc-Plated
Order No. Trade Size Pkg. Qty.PFC30282 1/4 100PFC30288 5/16 100PFC30289 3/8 100PFC72418 7/16 50PFC72419 1/2 50PFC30292 9/16 50PFC30293 5/8 50PFC30294 3/4 25PFC30295 7/8 25PFC30296 1 25PFC21081 1-1/8 25PFC42963 1-1/4 19PFC42986 1-1/2 13
2015 Catalog.indb 110 12/26/14 10:49 AM
111
Fasteners
ALASKA INDUSTRIAL HARDWARE, INC.
AIH Order Desk(907) 276-72011-800-478-7201www. .com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Cut WashersGalvanized
Order No. Trade Size Pkg. Qty.5GW14 1/4 7465GW516 5/16 4505GW38 3/8 3355GW12 1/2 1295GW58 5/8 645GW34 3/4 455GW78 7/8 32
Flat WashersA325
Hardened steel and zinc-plated construction.
Order No. Size In. Pkg. Qty.Hardened Steel
PFC21387 1/4 100PFC21389 5/16 100PFC21390 3/8 100PFC21391 7/16 50PFC21407 1/2 50PFC21427 9/16 25PFC21440 5/8 25PFC21451 3/4 20PFC21514 7/8 10PFC21548 1 10
Zinc PlatedPFC39216 1/4 54PFC39188 5/16 36PFC39187 3/8 24PFC39092 7/16 22PFC39091 1/2 18PFC39090 5/8 12PFC39723 3/4 8
Flat WashersStainless Steel
Order No. Size Pkg. Qty.PFC12139 #6 100PFC12141 #8 100PFC12143 #10 100PFC12145 1/4" 100
Lock Washers
Order No. Trade Size Pkg. Qty.Zinc-Plated
PFC42903 8 100PFC42904 10 100PFC42905 1/4 100PFC42906 5/16 100PFC42907 3/8 100PFC42908 7/16 100PFC42909 1/2 100PFC42910 9/16 100PFC42911 5/8 100PFC42912 3/4 100
Stainless SteelPFC14921 6 100PFC12128 8 100PFC12130 10 100PFC12132 1/4 100SSL14 1/4 100SSL516 5/16 100SSL12 1/2 100
Hardened AlloyPFC60331 1/4 100PFC60333 5/16 100PFC60335 3/8 100PFC60337 7/16 100PFC60339 1/2 100PFC56332 9/16 100PFC60341 5/8 100PFC60343 3/4 100PFC60345 7/8 100PFC60347 1 100
GalvanizedPFC71851 1/4 100PFC71852 5/16 100PFC71853 3/8 100PFC71854 1/2 100PFC71855 5/8 100PFC71856 3/4 100
Cut WashersStainless Steel
Order No. Size In. Pkg. Qty.SSW14 1/4 100SSW38 3/8 100SSW516 5/16 100SSW12 1/2 100
Fender Washers
Large area. Zinc-plated.
Order No. ID In. OD In. Pkg. Qty.PFC42992 3/16 1-1/4 100PFC42993 1/4 1 100PFC42995 1/4 1-1/2 100PFC42996 5/16 1-1/4 100PFC42990 3/8 1-1/2 100PFC98638 3/8 2 100PFC42999 1/2 2 100
Fender WashersStainless Steel
Grade 18-8 stainless steel construction. Size name corresponds to matching screw or bolt sizes.
Order No. ID In. OD In. Pkg. Qty.PFC12146 #8 (5/32) 3/4 100PFC12370 3/16 1 100PFC12152 1/4 1-1/4 50
Finish Washers
Nickel-plated.
Order No. Trade Size Pkg. Qty.PFC73001 6 100PFC73002 8 100PFC73003 10 100PFC73004 12 50
Foundation WashersSquare
Galvanized construction.
Order No. Dim. In. Pkg. Qty.KIR58GSW 5/8 x 3 x 3 50
2015 Catalog.indb 111 12/26/14 10:49 AM
112
Fasteners
GHD Order Desk(907) 279-66911-800-478-4393
2192 VIKING DRIVEANCHORAGE, AK 99501
GENERAL HARDWAREDISTRUBUTORSwww.ghdalaska.com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Tapping ScrewsStainless Steel — Phillips Drive
Flat Head
Pan HeadOrder
No.TradeSize
Lgth.In.
Pkg.Qty.
Flat HeadPFC12239 #6 1/2 100PFC12249 #6 3/4 100PFC12251 #6 1 100PFC12257 #8 1/2 100PFC12259 #8 3/4 100PFC12261 #8 1 100PFC12265 #8 1-1/2 50PFC12267 #8 2 50PFC12270 #10 1/2 100PFC12274 #10 3/4 100PFC12275 #10 1 100PFC12279 #10 1-1/2 50PFC12280 #10 2 50PFC12283 #12 3/4 100PFC12287 #12 1 100PFC12288 #12 1-1/2 50PFC12293 #12 2 25
Pan HeadPFC15039 #6 3/4 100PFC12295 #6 1 100PFC12300 #8 1/2 100PFC12302 #8 3/4 100PFC12304 #8 1 100PFC12306 #8 1-1/2 100PFC12310 #8 2 50PFC12312 #10 1/2 100PFC12314 #10 3/4 100PFC12316 #10 1 100PFC12317 #10 1-1/2 50PFC12318 #10 2 50PFC12320 #12 1/2 100PFC12322 #12 3/4 100PFC12323 #12 1 50PFC12324 #12 1-1/2 50PFC12328 #12 2 25
Sheet Metal ScrewsPan Head — Phillips
Self-DrillingOrder
No.Thread
SizeLgth.
In.Pkg.Qty.
PFC62275 6-20 3/8 100PFC62276 6-20 1/2 100PFC62243 8-18 3/4 100PFC62241 8-18 1/2 100PFC62244 8-18 1 100PFC62245 8-18 1-1/2 50PFC62246 10-16 1/2 100PFC62248 10-16 3/4 100PFC62249 10-16 1 100
Sheet Metal Screws Pan Head — Combo Drive
TappingOrder No. Trade Size Lgth. In. Pkg. Qty.PFC98803 6 1/2 150PFC98806 6 5/8 150PFC98807 6 3/4 130PFC98790 6 1 100PFC98791 6 1-1/4 80PFC98792 6 1-1/2 60PFC00080 8 3/8 130PFC00109 8 1/2 130PFC00140 8 5/8 100PFC00232 8 3/4 100PFC98821 8 1 80PFC00029 8 1-1/4 80PFC00040 8 1-1/2 60PFC00059 8 2 50PFC98455 10 1/2 100PFC29798 10 3/4 80PFC98357 10 1 80PFC98367 10 1-1/4 100PFC98439 10 1-1/2 75PFC98441 10 2 50PFC13180 12 3/4 60PFC98460 12 1 50PFC29800 12 1-1/2 35PFC98468 12 2 30PFC13022 14 1/2 100PFC98505 14 3/4 40PFC98507 14 1 35PFC98509 14 1-1/2 30PFC98516 14 2 20
Self-Drilling ScrewsHex Washer Head
Zinc-plated.Order No. Trade Size Lgth. In. Pkg. Qty.
No. 2 Point PFC62252 8 1/2 100PFC62254 8 3/4 100PFC62255 8 1 100PFC62256 8 1-1/4 100PFC62257 8 1-1/2 50PFC62258 10 1/2 100
No. 3 PointPFC62260 10 3/4 100PFC62261 10 1 100PFC62262 10 1-1/4 100PFC62263 10 1-1/2 50PFC62264 12-14 3/4 100PFC62265 12-14 1 50PFC62266 12-14 1-1/4 50PFC62267 12-14 1-1/2 50PFC07374 14-14 2 25PFC46403 14-14 3 25
Sheet Metal ScrewsHex Head — Tapping
OrderNo.
TradeSize
Lgth.In.
Pkg.Qty.
PFC75057 6 3/8 100PFC75058 6 1/2 100PFC75060 6 3/4 100PFC75073 8 1/2 100PFC75075 8 3/4 100PFC75076 8 1 100PFC75078 8 1-1/2 50PFC75080 8 2 50PFC75092 10 1/2 100PFC75094 10 3/4 100PFC75095 10 1 50PFC75096 10 1-1/4 50PFC75097 10 1-1/2 50PFC75099 10-24 2 50PFC75123 14 3/4 50PFC75124 14 1 50PFC75126 14 1-1/2 50PFC75128 14 2 25
Sheet Metal ScrewsSlotted Hex Head — Tapping
Stainless Steel
Stainless steel construction.
Order No. Trade Size Lgth. In.Pkg.Qty.
PFC12338 8 1/2 100PFC12341 8 3/4 100PFC12343 8 1 100PFC12349 10 1/2 100PFC12355 10 3/4 100PFC12356 10 1 100PFC12357 10 1-1/2 50PFC12359 12 3/4 100PFC12362 12 1 50PFC12366 12 1-1/2 50
2015 Catalog.indb 112 12/26/14 10:49 AM
113
Fasteners
ALASKA INDUSTRIAL HARDWARE, INC.
AIH Order Desk(907) 276-72011-800-478-7201www. .com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Self-Drilling ScrewsTeks® — Heavy-Duty
Includes washer.
Order No. Size Pkg. Qty.PFC13077 #14 x 2" 25PFC23791 #12-14 x 1-1/2" 25PFC23961 #14-14 x 3/4" 25PFC23859 #14-14 x 1" 25PFC23913 #14-14 x 1-1/2" 25PFC23825 #12-14 x 3/4" 50PFC23776 #12-14 x 1" 50PFC23817 #12 x 3/4" 50PFC23772 #12 x 1" 250PFC23784 #12 x 1-1/2" 250PFC23837 #14 x 1" 250PFC23898 #14 x 1-1/2" 250PFC16020 #14 x 2" 250
Self-Drilling ScrewsK-Lath — Phillips
Order No. Size Pkg. Qty.PFC19243 8-18 x 1/2" 100PFC19258 8-18 x 3/4" 100PFC19265 8-18 x 1" 100PFC19273 8-18 x 1-1/4" 100PFC12745 #8 x 9/16" 1 Lb.PFC12747 #8 x 3/4" 1 Lb.PFC12751 #8 x 1-1/4" 1 Lb.PFC12744 #8 x 9/16" 5 Lb.PFC12746 #8 x 3/4" 5 Lb.PFC12748 #8 x 1" 5 Lb.PFC12750 #8 x 1-1/2" 5 Lb.
Phillips Bugle Head CoarseDrywall Screws
General purpose screws for use on sheet rock and other materials.
Mfg.No.
OrderNo. Ga.
Lgth. In.
Pkg.Qty.
BlackCS114 8M/BOX NAR10313 6 1-1/4 8000114CDWS1 NAR10301 6 1-1/4 1 Lb. box114CDWS5 NAR10304 6 1-1/4 5 Lb. boxCS158 5M NAR10334 6 1-5/8 5000158CDWS 1# NAR10319 6 1-5/8 1 Lb. box158CDWS 5# NAR10322 6 1-5/8 5 Lb. boxCS6200 NAR10352 6 2 35002CDWS 1# NAR10337 6 2 1 Lb. box2CDWS 5# NAR10340 6 2 5 Lb. box212CDWS 1# NAR10370 8 2-1/2 1 Lb. box212CDWS 5# NAR10373 8 2-1/2 5 Lb. boxCS300 NAR51108 8 3 20003CDWS 1# NAR10391 8 3 1 Lb. box3CDWS 5# NAR10394 8 3 5 Lb. box
Yellow114GS1 NAR10880 6 1-1/4 1 Lb. box114GS5 NAR10883 6 1-1/4 5 Lb. box158GS1 NAR10901 6 1-5/8 1 Lb. box158GS5 NAR10904 6 1-5/8 5 Lb. box2GS1 NAR10913 6 2 1 Lb. box2GS5 NAR10916 6 2 5 Lb. box212GS1 NAR10931 8 2-1/2 1 Lb. box212GS5 NAR10934 8 2-1/2 5 Lb. box3GS1 NAR10946 8 3 1 Lb. box3GS5 NAR10949 8 3 5 Lb. box
Bugle Head Drywall ScrewsSelf-Drilling
Used for fastening drywall to 14-20 gauge metal studs. Posi-Grip drill point provides easier cutting and faster penetration. Black phosphate.
Mfg. No. Order No. Ga. Lgth. In. Pkg. Qty.SD114 NAR51329 6 1-1/4 8000SD1141 NAR51589 6 1-1/4 1 Lb. boxSD1145 NAR51605 6 1-1/4 5 Lb. box
Phillips Head Multi-Purpose Wood Screws
For outdoor applications. Yellow zinc.
Mfg. No. Order No. Ga. Lgth. In. Pkg. Qty.GS114 NAR10889 6 1-1/4 8000GS158 5M NAR51137 6 1-5/8 5000GS200 NAR51138 6 2 3500GS212 NAR51139 8 2-1/2 2500GS300 NAR51141 8 3 2000
Primeguard Exterior Screws
NAR 10255
NAR 10256Corrosion resistant screws for outdoor ap-plications.
Mfg. No. Order No. Ga. Lgth. In. Pkg. Qty.Combo Drive
P158S1 NAR10255 8 1-5/8 1 Lb. boxP158S5 NAR10256 8 1-5/8 5 Lb. boxP212S1 NAR10261 9 2-1/2 1 Lb. boxP212S5 NAR10262 9 2-1/2 5 Lb. boxP3S1 NAR10264 9 3 1 Lb. boxP3S5 NAR10265 9 3 5 Lb. boxP4S1 NAR10270 10 4 1 Lb. boxP4S5 NAR10272 10 4 5 Lb. box
Star DrivePSTB1 NAR53142 9 3 1 Lb. boxP3STBK NAR53143 9 3 5 Lb. box
2015 Catalog.indb 113 12/26/14 10:49 AM
114
Fasteners
GHD Order Desk(907) 279-66911-800-478-4393
2192 VIKING DRIVEANCHORAGE, AK 99501
GENERAL HARDWAREDISTRUBUTORSwww.ghdalaska.com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Wood ScrewsHeavy-Duty — TimberLok®
Heat treated steel construction with corro-sion-resistant coating. Features sharp point, tapered head and aggressive thread.
Mfg.No.
Order No.
Lgth.In.
Pkg.Qty.
FMTLOK04-12 FAS41484 4 12FMTLOK06-12 FAS41485 6 12FMTLOK08-12 FAS41486 8 12FMTLOK10-12 FAS41487 10 12FMTLOK04-50 FAS40018 4 50FMTLOK06-50 FAS40004 6 50FMTLOK08-50 FAS40009 8 50FMTLOK10-50 FAS40014 10 50FMTLOK04-250 FAS40020 4 250FMTLOK06-250 FAS40003 6 250FMTLOK08-250 FAS40008 8 250FMTLOK10-250 FAS40013 10 250
FASTER EASIER STRONGER
Wood ScrewsLoghog®
Extra heavy-duty log fastener, engineered for log home construction. Oversized head, thicker diameter and additional thread for in-creased draw-down and holding power. Cor-rosion resistant guaranteed.
Mfg. No. Order No. Lgth. In. Pkg. Qty.LHOG012 FAS40524 12 250LHOG015 FAS40527 15 150LHOG007 FAS41063 7 250LHOG010 FAS41731 10 250
Flathead ScrewsHeadLok®
Features wafer head eliminating need for washers, chamfer under head for increased strength, aggressive thread for holding and withdrawal strength, sharp gimlet point for fast installation, Spider Drive™ system de-sign for high level bit engagement and driv-ability, and includes spider drive bit.
Mfg. No. Order No. Lgth. In. Pkg. Qty.FMHLGM278-12 FAS41488 2-7/8 12FMHLGM412-12 FAS41489 4-1/2 12FMHLGM006-12 FAS41490 6 12FMHLGM278-50 FAS41060 2-7/8 50FMHLGM412-50 FAS41058 4-1/2 50FMHLGM006-50 FAS41059 6 50FMHLGM278-500 FAS41034 2-7/8 500FMHLGM412-250 FAS41035 4-1/2 500FMHLGM006-250 FAS41036 6 250
Pole Barn ScrewsWoodbinder
Order No. Size Pkg. Qty.PFC13051 #10 x 2" 50PFC13053 #10 x 3" 50PFC13052 #10 x 2-1/2" 50PFC13049 #10 x 1" 100PFC13050 #10 x 1-1/2" 100PFC24255 #10 x 2-1/2" 250PFC24125 #10 x 1-1/2" 500
Wood ScrewsFlat Head — Phillips
OrderNo.
TradeSize
Lgth.In.
Pkg.Qty.
PFC74201 4 1/2 100PFC74203 4 3/4 100PFC13024 4 1 100PFC74212 6 1/2 100PFC74214 6 3/4 100PFC74216 6 1 100PFC74217 6 1-1/4 100PFC74218 6 1-1/2 100PFC74220 6 2 100PFC74231 8 1/2 100PFC74233 8 3/4 100PFC74235 8 1 100PFC74236 8 1-1/4 100PFC74237 8 1-1/2 100PFC74239 8 2 50PFC74241 8 2-1/2 50PFC74242 8 3 50PFC74262 10 3/4 100PFC74263 10 1 100PFC74264 10 1-1/4 100PFC74265 10 1-1/2 50PFC74267 10 2 50PFC74268 10 2-1/2 50PFC74269 10 3 25PFC74282 12 1 100PFC74283 12 1-1/4 50PFC74284 12 1-1/2 50PFC74286 12 2 50PFC74287 12 2-1/2 50PFC74288 12 3 25PFC74292 1/4 1 50PFC74293 1/4 1-1/4 50PFC74294 1/4 1-1/2 50PFC74296 1/4 2 25PFC74297 1/4 2-1/2 25PFC74298 1/4 3 20
Brass Wood ScrewsFlat Head — Phillips Drive
Brass construction.
OrderNo.
TradeSize
Lgth.In.
Pkg.Qty.
PFC75944 6 3/4 100PFC75945 6 1 50PFC75946 6 1-1/4 50PFC75947 6 1-1/2 50PFC75961 8 1/2 50PFC75963 8 3/4 50PFC75964 8 1 50PFC75965 8 1-1/4 50PFC75966 8 1-1/2 25PFC75967 8 2 25PFC75982 10 1 25PFC75983 10 1-1/4 25PFC75984 10 1-1/2 25PFC75985 10 2 25PFC75993 12 1-1/2 25PFC75994 12 2 15
2015 Catalog.indb 114 12/26/14 10:49 AM
115
Fasteners
ALASKA INDUSTRIAL HARDWARE, INC.
AIH Order Desk(907) 276-72011-800-478-7201www. .com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
StrutsGalvanized
Steel construction featuring electrogalva-nized finish.
Mfg. No. Order No. Dim. In. H x W x LRP1000T10PG UNI04489 1-5/8 x 1-5/8 x 120RP4100T10PG UNI04490 1-5/8 x 13/16 x 120
Clevis SpliceGalvanized
9/16" hole diameter. Carbon steel construc-tion. Features 4-holes.
Mfg. No. Order No. Dim. In. L x WRP1377EG UNI04537 1-5/8 x 7-1/4
Beam ClampsGalvanized
Durable, cast iron con-struction. Provides rod or insulator support. Meets the physical requirements of ASTM A1011 SS GR 33.
Mfg.No.
OrderNo.
FlangeWidth In.
LoadRating Lbs
RP2894-50EG UNI04471 1/2 x 7/8 400RP2894-37EG UNI04470 3/8 x 7/8 350RP2894-25EG UNI04469 1/4 x 7/8 150
Conduit Clamps
Steel construction featuring electrogalvanized finish. Fits rigid, IMC, pipe, and EMT.
Mfg. No. Order No. Size In. O.D. In.RP1211EG UNI04496 1/2 .706 - .840RP1212EG UNI04497 3/4 .922 - 1.25RP1213EG UNI04498 1 1.163 - 1.315RP1214EG UNI04499 1-1/4 1.74 - 1.9RP1215EG UNI04500 1-1/2 1.74 - 1.9RP1217EG UNI04501 2 2.197 - 2.375
Spring Nuts
Steel, electrogalvanized construction. Fea-tures 20 threads. Includes 5 per package.
Mfg. No. Order No. Hole Dia. In.RP1006T1420EG UNI04479 1/4RP1008EG UNI04480 3/8RP1010EG UNI04481 1/2
Angle BracketsUniversal — Galvanized
1/2" hole diameter. Carbon steel construc-tion. 90-degree angled plate bracket.
Mfg. No. Order No. Dim. In. L x WRP2484EG UNI04535 4 x 1-5/8
Angle BracketsGalvanized
9/16" hole diameter. Hot rolled carbon steel construc-tion. 90-degree angle bracket featuring 4-holes.
Mfg. No. Order No. Dim. In. L x WRP1325EG UNI04472 4-1/2 x 1-1/8
Angle BracketsGalvanized
Carbon steel construction. 2-hole, 90-degree angled plate bracket.
Mfg. No. Order No. Dim. In. L x WRP1026EG UNI04536 1-5/8 x 1-7/8
Flat BracketsGalvanized
1/2" hole diameter. Hot rolled carbon steel construction.
Mfg. No. Order No. Dim. In. L x W Hole Qty.RP1065EG UNI04473 3-1/2 x 1-5/8 2RP1067EG UNI04475 7-1/4 x 1-5/8 4
Corner BracketGalvanized
1/2" hole diameter. Hot rolled steel construc-tion. 3-hole, corner plate bracket.
Mfg. No. Order No. Dim. In. L x WRP1036EG UNI04474 3-1/2 x 3-1/2
T-Shaped BracketsGalvanized
9/16" hole diameter. Carbon steel construc-tion. 4-hole, tee plate bracket.
Mfg. No. Order No. Dim. In. L x WRP1031EG UNI04538 3-1/2 x 1-5/8
Square WashersGalvanized
Square construction featuring steel, electro-galvanized finish. Includes 5 per package.
Mfg. No. Order No. Hole Dia. In.RP1062EG UNI04476 5/16RP1063EG UNI04477 318RP1064EG UNI04478 1/2
2015 Catalog.indb 115 12/26/14 10:49 AM
116
Fasteners
GHD Order Desk(907) 279-66911-800-478-4393
2192 VIKING DRIVEANCHORAGE, AK 99501
GENERAL HARDWAREDISTRUBUTORSwww.ghdalaska.com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Injection Adhesive Anchoring Systems
AC100+ GOLD®
POW8478SD
POW8490SD
Two-component vinylester adhesive anchor-ing system designed for bonding threaded rod and reinforcing bar hardware into drilled holes in concrete and masonry based mate-rials. Includes mixing nozzle. Meets ICC-ES AC308 criteria and ASTM E 1512 specs.
Mfg. No. Order No. Size8478SD POW8478SD 10 oz.8490SD POW8490SD 29 oz.
Manual Injection ToolsAC100+ Gold™
High performance manual injecting tool for AC100+™ adhesive.
Mfg. No. Order No. Size Oz.08495 POW08495 29
Adhesive Mixing NozzlesAC100+™ & PE1000+™
Replacement mixing nozzles. For use with 29oz. AC100+™ adhesive and 13 oz. PE1000+™ epoxy.
Mfg. No. Order No. Pkg. Qty.08294 POW08294 2
Adhesive Anchoring SystemsPE1000+
Two-component, high strength epoxy adhe-sive anchoring system. Designed for bonding threaded rod and reinforcing bar hardware into drilled holes in concrete base materials.
Mfg. No. Order No. Size Fl. Oz.0500SD POW0500SD 130502SD POW0502SD 20
Manual Injection ToolsPE1000+™ Adhesive
High performance manual injecting dispens-ing tool for injecting PE1000+™ adhesive.
Mfg. No. Order No. Size Oz.08298 POW08298 13 & 20 adhesives
Concrete ScrewsTapper®
Designed to meet the needs of most light to medium duty applications in concrete, block and brick.
Mfg.No.
OrderNo.
Dia.In.
Lgth.In.
Pkg.Qty.
Hex Head 02700 POW02700 3/16 1-1/4 10002702 POW02702 3/16 1-3/4 10002722 POW02722 1/4 1-3/4 10002724 POW02724 1/4 2-1/4 10002726 POW02726 1/4 2-3/4 10002728 POW02728 1/4 3-1/4 1002730SD POW02730 1/4 3-3/4 100
Phillips Flat Head02740 POW02740 3/16 1-1/4 10002742 POW02742 3/16 1-3/4 10002762 POW02762 1/4 1-1/4 10002764 POW02764 1/4 2-1/4 10002766 POW02766SD 1/4 2-3/4 10002768 POW02768 1/4 3-1/4 100
Concrete ScrewsTapper®
Hex head concrete screw is fully threaded for light gauge metal attachment. 5/16" hex head with #3 Phillips. 100 per package.
Mfg. No. Order No. Lgth. In..2200SD POW2200SD 1-3/42202SD POW2202SD 2-1/42204SD POW2204SD 2-3/42206SD POW2206SD 3-1/42208SD POW2208SD 4
Concrete ScrewsTapper®
Phillips flat head concrete screw is fully threaded for light gauge metal attachment. 5/16" hex head with #3 Phillips. 100 per package.
Mfg. No. Order No. Lgth. In..2212SD POW2212SD 2-1/42214SD POW2214SD 2-3/42216SD POW2216SD 3-1/42218SD POW2218SD 4
NOTES________________________________________________________________________________________________________________________________
2015 Catalog.indb 116 12/26/14 10:49 AM
117
Fasteners
ALASKA INDUSTRIAL HARDWARE, INC.
AIH Order Desk(907) 276-72011-800-478-7201www. .com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Concrete AnchorsWedge-Bolt®
Zinc plated, carbon steel body screw anchor with finished hex head. Steel threads along body tap into hole during installation. De-signed for structural loading in cracked and uncracked concrete. Use Wedge-Bits™ that match the nominal anchor diameter to drill holes for the anchors.
Mfg. No.
OrderNo.
Size In.Dia. x L
Pkg.Qty.
7210SD POW7210SD 1/4 x 3 1007224SD POW7224SD 3/8 x 3 507244SD POW7244SD 1/2 x 3 507246SD POW7246SD 1/2 x 4 507262SD POW7262SD 5/8 x 4 257266SD POW7266SD 5/8 x 6 25
Concrete BitsSDS-max® — SpeedX™
High drilling speed with inclined side cutters for fast concrete drilling. Compact head for fast dust removal and long life. Active-center-ing tip provides quick, accurate starts. Wear mark indicator assures accuracy of hole di-ameter.
Mfg.No.
OrderNo.
Size In.Dia. x L.
UsableLgth. In.
HC5081 BSHHC5081 1-3/8 x 21 16
Concrete SDS-Plus BitsWedge-Bit™
For proper performance the Wedge-Bolt® anchors must be installed with a Wedge-Bit™. It has a special matched tolerance range designed to provide optimum perfor-mance for the anchor.
Mfg. No.
OrderNo.
Size In.Dia. x L
Usable Lgth. In.
01314 POW01314 1/4 x 6 401316 POW01316 3/8 x 6 401320 POW01320 1/2 x 6 401324 POW01324 5/8 x 8 6
Wedge Expansion AnchorsPower Stud™ + SD1
Fully threaded, torque-controlled, wedge expansion anchor is designed for consistent performance in cracked and un-cracked con-crete. Tested in accordance with ACI 355.2 and ICC-ES AC 193. For use in concrete un-der the design provisions of ACI 318.
Mfg. No. Order No. Lgth. In. Pkg. Qty.1/4" Diameter
7400SD1 POW7400SD1 1-3/4 1007402SD1 POW7402SD1 2-1/4 1007404SD1 POW7404SD1 3-1/4 100
3/8" Diameter7410SD1 POW7410SD1 2-1/4 507412SD1 POW7412SD1 2-3/4 507415SD1 POW7415SD1 3-3/4 507416SD1 POW7416SD1 5 50
1/2" Diameter7420SD1 POW7420SD1 2-3/4 507422SD1 POW7422SD1 3-3/4 507423SD1 POW7423SD1 4-1/2 507424SD1 POW7424SD1 5-1/2 507426SD1 POW7426SD1 7 50
5/8" Diameter7430SD1 POW7430SD1 3-1/2 257432SD1 POW7432SD1 4-1/2 257433SD1 POW7433SD1 5 257434SD1 POW7434SD1 6 257436SD1 POW7436SD1 7 257438SD1 POW7438SD1 8-1/2 25
3/4" Diameter7440SD1 POW7440SD1 4-1/4 207441SD1 POW7441SD1 4-3/4 207442SD1 POW7442SD1 5-1/2 207444SD1 POW7444SD1 6-1/4 207446SD1 POW7446SD1 7 207448SD1 POW7448SD1 8-1/2 107449SD1 POW7449SD1 10 10
Split Fast AnchorsFlat Head
High-grade steel construction for use in con-crete, stone and hard masonry. Exerts ex-pansive pressure on inner walls of pre-drilled holes, creating secure mounting. 1/4" diam-eter; minimum embedment 1-1/8".
Order No. Lgth. In. Pkg. Qty.PFC24458 1-1/2 100PFC24460 2 100PFC24461 2-1/2 100PFC24464 3 100PFC24470 4 100
Nail Drive AnchorsZamac Nailin®
The Zamac Nailin® is a nail drive anchor which has a body formed from Zamac alloy. Drive nails are carbon steel. The anchor can be used in concrete, block, brick or stone.
Mfg. No. Order No. Dia. In. Lgth. In. Pkg. Qty.02806 POW02806 1/4 3/4 10002808 POW02808 1/4 1 10002814 POW02814 1/4 1-1/4 10002820 POW02820 1/4 1-1/2 10002826 POW02826 1/4 2 100
Nail Drive AnchorsZamac Hammer-Screw®
The Zamac Hammer-Screw® is a unique, one-step nail drive anchor featuring a Phillips type flat head and a screw thread for use in concrete, block, brick or stone.
Mfg. No. Order No. Dia. In. Lgth. In. Pkg. Qty.02842 POW02842 1/4 1-1/4 10002844 POW02844 1/4 1-1/2 100
Drop-In AnchorsZinc
Can be used in solid concrete, hard stone, and solid block base materials.
Mfg. No. Order No. Size In. Pkg. Qty.06324 POW06324 1/4 10006326 POW06326 3/8 5006328 POW06328 1/2 5006320 POW06320 5/8 2506312 POW06312 3/4 10
Drop-In AnchorsSetting Tool
For setting drop-in anchors.
Mfg. No. Order No. Size In.06305 POW06305 1/406307 POW06307 3/806309 POW06309 1/206311 POW06311 5/806313 POW06313 3/4
2015 Catalog.indb 117 12/26/14 10:49 AM
118
Fasteners
GHD Order Desk(907) 279-66911-800-478-4393
2192 VIKING DRIVEANCHORAGE, AK 99501
GENERAL HARDWAREDISTRUBUTORSwww.ghdalaska.com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Concrete Forming SpikesDuplex Head
The SPIKE® anchor is a one-piece, tamper-proof vibration resistant anchor for use in concrete, block, brick or stone. The SPIKE® anchor is formed with an S-shaped configu-ration at the working end of the anchor to cre-ate an expansion mechanism.
Mfg. No. Order No. Dia. In. Lgth. In. Pkg. Qty.03794 POW03794 1/4 2-3/4 100
Tamper Proof SpikesThe Spike®
Carbon steel mushroom head one-piece, tamper-proof vibration resistant anchor for use in concrete, block, brick or stone. Formed with an S-shaped configuration at the working end of the anchor to create an expansion mechanism.
Mfg.No.
OrderNo.
Dia.In.
Lgth.In.
Pkg.Qty.
03758 POW03758 1/4 1-3/4 50
Adhesive Anchoring AccessoriesHand Pump / Dust Blower
Used in preparation with various anchoring applications and for supporting proper an-chor installation.
Mfg. No. Order No. Desc.08280 POW08280 Dust blowout pump
Wire BrushesHole Clean Out
Steel wire brush for cleaning out holes in concrete or masonry before installing me-chanical or epoxy anchor system.
Mfg.No.
OrderNo.
Dia.In.
Lgth. In.
Hole Dia. In.*
08284 POW08284 3/8 6-3/4 7/1608285 POW08285 1/2 6-3/4 9/1608286 POW08286 5/8 7-7/8 11/1608287 POW08287 3/4 7-7/8 7/808289 POW08289 1 11-7/8 1-1/808290 POW08290 1-1/4 11-7/8 1-3/808291 POW08291 1-1/2 11-7/8 1-1/2* ANSI Hole Size
Drill Adaptersfor Steel Brush
Attaches to drill chuck for fast cleanout with steel brushes (sold seperately).
Mfg. No. Order No. Desc.08296 POW8296 For 3/8" and 1/2" chucks
Rod Hanging SystemsVertigo®
One-piece, all steel threaded fastening sys-tem for suspending steel threaded rod verti-cally overhead in pipe hanging, fire protec-tion, electrical conduit and cable-tray appli-cations.
Mfg. No.
OrderNo.
Rod Size In.
Screw Shank and Lgth. In.
Pkg. Qty.
Wood Side Hanger07156 POW07156 3/8 3/8 x 2-1/2 100
07170 POW07170 3/8 1/4 x 2 100
07185 POW7185 1/4 1/4 x 1 100
Steel Vertical Hanger07158 POW07158 3/8 1/4–20 x 1 100
07159 POW07159 3/8 1/4–20 x 1-1/2 100
Wood Vertical Hanger07162 POW07162 3/8 3/8 x 2-1/2 100
07163 POW7163 1/4 1/4 x 2 100
07165 POW07165 3/8 1/4 x 2 100
07167 POW07167 3/8 1/4 x 3 100
07203 POW07203 3/8 1/4 x 1 100
Vertigo SocketsUniversal
1/4" hex shaft fits drill or impact driver for fast installation of vertigo threaded rod hangers.
Mfg. No. Order No. Color07187 POW07187 Red
Powder-Actuated ToolsSemi-Automatic Kit
The P3500™ is a low velocity, semi-automat-ic .27 caliber tool used to install .300 head drive pins, 8mm head drive pins and 1/4"-20 threaded studs, up to 3" in total length. Uses 10 load strips. Designed for high speed and repetitive volume applications. The P3500™ Deluxe Kit includes: safety glasses, dispos-able ear plugs, allen wrenches, wire brushes, tool lubricant, spall guard, pin starter kit, and plastic case.
Mfg.No.
OrderNo.
PinLgth. In.
Lgth.In.
Wt. Lbs.
52000 POW52000 1/2 — 3 13-5/8 5
Powder-Actuated ToolsSingle-Shot
The P2201™ is a low velocity, single-shot, .22 caliber tool used to install .300 head drive pins, 8mm head drive pins and 1/4"-20 threaded studs, up to 3" in total length. The P2201™ is designed for maintenance or residential contractors.
Mfg.No.
OrderNo.
Pin Lgth. In.
Lgth.In.
Wt. Lbs.
52007 POW52007 1/2 – 3 12-1/2 4.3
Powder-Actuated ToolsHammer Drive
The P1000™ is a .22 caliber, hammer actu-ated do-it-yourself tool. Engineered for high reliability, low maintenance, and speed. Used in remodeling, electrical fixtures, mainte-nance and telecommunication applications.
Mfg.No.
OrderNo.
Pin Lgth. In.
Lgth. In.
Wt. Lbs.
52013 POW52013 1/2 – 3 13 3
2015 Catalog.indb 118 12/26/14 10:49 AM
119
Fasteners
ALASKA INDUSTRIAL HARDWARE, INC.
AIH Order Desk(907) 276-72011-800-478-7201www. .com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Drive Pins
Drive pins for permanently fastening fixtures to concrete, some types of concrete block and A36 or A572 structural steel. Head size: .300"; Shank size: .145".
Mfg. No. Order No. Lgth. In. Pkg. Qty.50022 POW50022 3/4 10050026 POW50026 1 10050032 POW50032 1-1/4 10050034 POW50034 1-1/2 10050038 POW50038 2 10050044 POW50044 2-1/2 100
Drive PinsWith Washers
Drive pins with 7/8" washers provide resis-tance to pullover. For permanently fastening fixtures to concrete. Head size: .300": shank size: .145".
Mfg. No. Order No. Lgth. In. Pkg. Qty.50090 POW50090 1 10050092 POW50092 1-1/4 10050094 POW50094 1-1/2 10050096 POW50096 2 10050098 POW50098 2-1/2 10050100 POW50100 3 100
Powder-Actuated ToolsPowder Loads
POW50504
POW50630, POW50626, POW50622
Powder-actuated tool loads.
Mfg. No. Order No. Color Pkg. Qty..22 Caliber Single Loads
50504 POW50504 Green 10050506 POW50506 Yellow 100
.27 Caliber Strip Loads50622 POW50622 Green 1050626 POW50626 Yellow 1050630 POW50630 Red 10
NOTES________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
NOTES________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
2015 Catalog.indb 119 12/26/14 10:49 AM
120
Fasteners
GHD Order Desk(907) 279-66911-800-478-4393
2192 VIKING DRIVEANCHORAGE, AK 99501
GENERAL HARDWAREDISTRUBUTORSwww.ghdalaska.com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Flat BarsSteel
1/8" thick. Zinc-plated.Mfg. No. Order No. Dim. In. L x W
1201/11088 STW11088 36 x 3/41203/11090 STW11090 36 x 11205/11092 STW11092 36 x 1-1/4
Flat Steel BarsWeldable
Mfg. No. Order No. Dim. In. H x W x L0701/11647 STW50701 1/8 x 1/2 x 360703/11649 STW51610 1/8 x 1/2 x 720704/11650 STW50704 1/8 x 3/4 x 360705/11651 STW51411 1/8 x 3/4 x 480706/11652 STW50706 1/8 x 3/4 x 720707/11653 STW50707 1/8 x 1 x 360708/11654 STW11654 1/8 x 1 x 48000709/11655 STW11655 1/8 x 1 x 720710/11656 STW50710 1/8 x 1-1/4 x 360711/11657 STW51412 1/8 x 1-1/4 x 480712/11658 STW50712 1/8 x 1-1/4 x 720713/11659 STW50713 1/8 x 1-1/2 x 360714/11660 STW51413 1/8 x 1-1/2 x 480717/11663 STW51414 1/8 x 2 x 480719/11665 STW50719 1/8 x 3 x 360749/11686 STW50749 1/4 x 1-1/2 x 360751/11688 STW50751 1/4 x 1-1/2 x 7211828 STW11828 1/4 x 3 x 72
Hot Rolled Steel PlatesWeldable
Used in a variety of industrial and farm machinery welding applications. Plain finish.
Mfg. No. Order No. Dim. In.11806 STW11806 1/4 x 4 x 1211807 STW11807 1/4 x 12 x 12
Angle BarsSteel
Zinc-plated. 1/8" thickness.
Mfg. No. Order No. Dim. In. H x W x L52301/11123 STW11123 3/4 x 3/4 x 3611124 STW11124 1 x 1 x 3652303/11125 STW52303 1-1/4 x 1-1/4 x 36
Angled Steel BarsWeldable
13 ga. steel.
Mfg. No. Order No. Dim. In. H x W x L0804/11700 STW50804 1/8 x 3/4 x 360805/11701 STW53411 1/8 x 3/4 x 480806/11702 STW53611 1/8 x 3/4 x 720807/11703 STW50807 1/8 x 1 x 360808/11704 STW53401 1/8 x 1 x 480809/11705 STW53601 1/8 x 1 x 720810/11706 STW50810 1/8 x 1-1/4 x 360811/11707 STW53412 1/8 x 1-1/4 x 480813/11709 STW50813 1/8 x 1-1/2 x 360814/11710 STW53413 1/8 x 1-1/2 x 480815/11711 STW53613 1/8 x 1-1/2 x 720817/11713 STW53414 1/8 x 2 x 4811719 STW11719 1/4 x 1-1/2 x 36
Slotted Steel StrapsZinc-Plated
Flat, zinc-plated, slotted, steel strap. 18 ga.
Mfg. No. Order No. Dim. In. W x L1433/11142 STW51433 2-1/4 x 3611145 STW11145 2-1/4 x 72
Slotted BarsGalvanized
1-3/8" wide, 14 gauge steel.
Mfg. No. Order No. Lgth. In.1401/11139 STW60301 361402/11140 STW60401 481403/11141 STW60601 72
Perforated Angle BarsSteel
Measures 1-1/4" x 1-1/4".
Mfg. No. Order No. Lgth. Ft.
12 Ga.
1533/11133 STW51533 3
1536/11135 STW51536 6
16 Ga.
1153/11136 STW51553 3
1156/11138 STW51556 6
Steel Slotted Angle BarsZinc-Plated
Mfg.No.
OrderNo.
Dim. In.H x W x L
SteelGauge
1513/11112 STW51513 1-1/4 x 1-1/4 x 36 181516/11115 STW51516 1-1/4 x 1-1/4 x 72 1861101/11104 STW61101 1-1/2 x 1-1/2 x 12 14
2015 Catalog.indb 120 12/26/14 10:49 AM
121
Fasteners
ALASKA INDUSTRIAL HARDWARE, INC.
AIH Order Desk(907) 276-72011-800-478-7201www. .com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Slotted Angle BarsGalvanized
Measures 1-1/2" H x 1-1/2" W. 14 gauge
Mfg. No. Order No. Lgth. In.1503/11111 STW61601 721501/11109 STW61301 36
Steel Slotted Angle BarsZinc-Plated — Offset
14 gauge steel.
Mfg. No. Order No. Dim. In. H x W x L11117 STW51523 2-1/4 x 1-1/2 x 361524/11118 STW51524 2-1/4 x 1-1/2 x 4811108 STW11108 2-1/4 x 1-1/2 x 120
Round RodsCold Rolled
36" length. Zinc-plated.
Mfg. No. Order No. Dia.In.1600/11150 STW30301 3/161601/11151 STW30302 1/41602/11152 STW30303 5/161603/11153 STW30304 3/830305/11223 STW30305 7/161604/11154 STW30306 1/21605/11155 STW30307 5/81606/11156 STW30308 3/430310/11166 STW30310 1
Steel RodsWeldable — Round
Mfg. No. Order No. Dim. In. Dia. x L0001/11593 STW50001 1/4 x 360002/11594 STW31402 1/4 x 480003/11595 STW31602 1/4 x 720004/11596 STW50004 5/16 x 360005/11597 STW31403 5/16 x 480008/11600 STW31404 3/8 x 480012/11604 STW31405 1/2 x 480401/11627 STW80401 1/8 x 360402/11628 STW31400 1/8 x 480403/11629 STW80403 3/16 x 360404/11630 STW31401 3/16 x 48
KeystockSteel
12" length. Zinc-plated.
Mfg. No. Order No. Size In.1650/11172 STW40101 1/81653/11173 STW40103 3/161656/11174 STW40105 1/41659/11175 STW40106 5/161662/11176 STW40107 3/85100/11185 STW40108 7/161665/11177 STW40109 1/2
Steel BarsWeldable — Square
Mfg. No. Order No. Thick. In. Lgth. In.0601/11643 STW80601 3/8 360604/11645 STW50604 1/2 36
Steel TubesWeldable — Round
Plain finish.Mfg. No. Order No. Dim. In. Dia. x L11747 STW11747 1/2 x 3611748 STW11748 3/4 x 3611749 STW11749 1 x 36
Steel TubesWeldable — Square
Mfg. No. Order No. Dim. In. W x L1001/11735 STW51001 1/2 x 361003/11737 STW51003 1/2 x 721004/11738 STW51004 3/4 x 361005/11739 STW45411 3/4 x 481006/11740 STW51006 3/4 x 721007/11741 STW51007 1 x 361008/11742 STW45412 1 x 481009/11743 STW51009 1 x 72
Steel TubesPerforated — Telescoping
Zinc plated. 12-gauge. Smaller size can be inserted into next biggest diameter to create telescoping effect. Mfg. No. Order No. Dim. In. W x L11190 STW11190 1 x 7211196 STW11196 1-1/2 x 72
Telescoping Steel Tube Accessories
STW11206 STW11207
Steel construction, 10 guage and zinc plated. Used to strengthen or hold together tele-scoping steel tubes.
Mfg. No. Order No. Desc.11206 STW11206 Inside angle bracket11207 STW11207 Gusset
2015 Catalog.indb 121 12/26/14 10:49 AM
122
Fasteners
GHD Order Desk(907) 279-66911-800-478-4393
2192 VIKING DRIVEANCHORAGE, AK 99501
GENERAL HARDWAREDISTRUBUTORSwww.ghdalaska.com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Aluminum BarsFlat
Mfg. No. Order No. Dim. In. H x W x L6201/11288 STW56201 1/8 x 3/4 x 366205/11292 STW56205 1/8 x 1 x 366207/11294 STW56207 1/8 x 1 x 726215/11299 STW56215 1/8 x 1-1/2 x 366217/11301 STW56217 1/8 x 1-1/2 x 726220/11303 STW56220 1/8 x 2 x 36
Aluminum BarsAngle
Mfg No. Order No. Dim. In. H x W x L6405/11329 STW56405 1/8 x 3/4 x 366410/11333 STW56410 1/8 x 1 x 366412/11335 STW56412 1/8 x 1 x 726415/11338 STW56415 1/8 x 1-1/2 x 366417/11340 STW56417 1/8 x 1-1/2 x 726425/11347 STW56425 1/16 x 3/4 x 366427/11349 STW56427 1/16 x 3/4 x 726430/11351 STW56430 1/16 x 1 x 366432/11353 STW56432 1/16 x 1 x 726434/11355 STW56434 1/16 x 1-1/2 x 36
Aluminum RodsRound
Mfg. No. Order No. Dim. In. Dia. x L6005/11270 STW56005 1/4 x 366010/11273 STW56010 3/8 x 3611277 STW11277 1/2 x 36
Brass RodsRound
Mfg. No. Order No. Dim. In. Dia. x L0301/11517 STW32301 1/8 x 360302/11518 STW32302 3/16 x 360303/11519 STW32303 1/4 x 360304/11520 STW50304 5/16 x 360305/11521 STW50305 3/8 x 360306/11522 STW50306 1/2 x 36
Aluminum TubesRound
Mfg. No. Order No. Dim. In Dia. x L6712/11399 STW56712 3/4 x 726718/11404 STW56718 1 x 72
Aluminum TubesSquare
Mfg. No. Order Dim. In. W x L6607/11388 STW56607 3/4 x 726615/11389 STW56615 1 x 366617/11391 STW56617 1 x 72
Aluminum Trim Channels
Aluminum construction. Used to tightly en-case 3/4" plywood or plexiglass.Mfg. No. Order No. Dim. In. W x L11385 STW11385 3/4 x 96
Steel SheetsWeldable
Weldable steel sheet.
Mfg. No. Order No. Dim. In. L x W16 Ga.
11763 STW11763 12 x 2411766 STW11766 24 x 24
22 Ga.18015/11811 STW18015 6 x 1818025/11812 STW18025 6 x 2418055/11815 STW18055 12 x 1818065/11816 STW18065 12 x 2418095/11817 STW18095 24 x 241812/11778 STW51812 24 x 36
Steel SheetsStainless
22 gauge, stainless steel sheet.
Mfg. No. Order No. Dim. In. L x W11591 STW57601 18 x 611592 STW57603 24 x 12
Steel SheetsGalvanized
26 gauge steel.
Mfg. No. Order No. Dim. In. L x W19035/11225 STW19035 12 x 1819045/11226 STW19045 12 x 2419055/11227 STW19055 24 x 24
2015 Catalog.indb 122 12/26/14 10:49 AM
123
Fasteners
ALASKA INDUSTRIAL HARDWARE, INC.
AIH Order Desk(907) 276-72011-800-478-7201www. .com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Sheet MetalSteel — Perforated
16 gauge (.0598") construction. Features 3/16" x 1/4" staggered holes. Weldable.
Mfg. No. Order No. Dim. In.2205/11796 STW52205 24 x 24
Expanded Steel SheetsWeldable
13 gauge
Mfg.No.
OrderNo.
MeshWidth In.
Dim. In.L x W
2102/11780 STW52102 3/4 24 x 242202/11795 STW52202 1/2 24 x 24
Aluminum Sheets
.025" thick.
Mfg. No. Order No. Dim. In. L x W20015/11483 STW20015 6 x 1820025/11484 STW20025 6 x 2420055/11486 STW20055 12 x 1820095/11487 STW20095 24 x 24
Brass Sheets
26 gauge brass sheeting.
Mfg. No. Order No. Dim. In. L x W11524 STW53300 12 x 24
Tread Plates
Mfg.No.
OrderNo.
Dim. In.L x W
Thick.In.
Standard Aluminum2050/11248 STW52050 12 x 24 .063
Steel2220/11799 STW52220 12 x 24 .075
Hitchpins
Red plastisol-coated head. Constructed from heat-treated, high tensile steel. Includes hair-pin clip.
Mfg.No.
OrderNo.
ShaftDia. In.
UsableLgth. In.
H12/00113 DHH00113 1/2 3-5/800123 DHH00123 5/8 5-1/2H43/00133 DHH00133 3/4 6-1/2H100-45 DHH00253 1 4-1/2
Lynchpins
Yellow zinc-plated with flag. Fits top link and lift pins.
Mfg. No.
Order No.
Shaft Dim. In.Dia. x L
FitsCategory
OALIn.
81911 DHH81911 3/16 x 1-1/8 0 1-5/881922 DHH81922 1/4 x 1-1/4 1 2-1/881933 DHH81933 5/16 x 1-1/4 1 & 2 2-1/8
Wirelock Pins
Yellow zinc-plated with flag. 2" shank length.
Mfg. No.
Order No.
Shaft Dim. In.Dia. x L
OALIn.
WireType
81975 DHH81975 1/4 x 1-3/4 2-1/4 Round81971 DHH81971 1/4 x 2-1/4 3 Square21992 DHH81992 3/8 x 1-3/4 2-5/16 Round21994 DHH81994 3/8 x 2-1/2 3-7/16 Square81981 DHH81981 5/16 x 2-1/4 3 Square81987 DHH81987 5/16 x 2-1/4 3 Round
NOTES________________________________________________________________________________________________________________________________
2015 Catalog.indb 123 12/26/14 10:49 AM
124
Fasteners
GHD Order Desk(907) 279-66911-800-478-4393
2192 VIKING DRIVEANCHORAGE, AK 99501
GENERAL HARDWAREDISTRUBUTORSwww.ghdalaska.com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Clevis PinsAdjustable
Multiple holes for multiple length applica-tions. Extra length can be cut off if needed Yellow zinc-plated finish. Clamshell packed.
Mfg. No.
OrderNo.
Dia.In.
Lgth.In.
Pkg.Qty.
32720 DHH32720 1/4 2 432730 DHH32730 5/16 2 332740 DHH32740 3/8 2 232742 DHH32742 3/8 3 232758 DHH32758 7/16 3 232765 DHH32765 1/2 2-1/2 232770 DHH32770 1/2 4 2
Clevis Pin SetsAdjustable
Kwic Kit Set ContentsDimension Inches
Dia. x Lgth. Qty.3/16 x 1-1/2 4
1/4 x 2 35/16 x 1-1/2 3
5/16 x 2 33/8 x 2 3
7/16 x 2 2Clevis Pin Sets
Mfg. No. Order No. Desc.15008 DHH15008 18-pc. Kwic Kit
Clevis PinsAssortment
Most popular clevis pin assortment set.
Mfg. No. Order No. Pc. Qty.W5359 WIM15990 74
Bent Pins
Universal pin for use on agricultural, recre-ational, industrial and construction equip-ment. Replaces clevis pins; easy to install and remove. Zinc-plated. Includes hairpin clip. Individually packed.
Mfg. No.
OrderNo.
Dia.In.
UsableLgth. In.
30312 DHH30312 1/2 330320 DHH30320 5/8 3
Hitchpin Clips
Constructed from zinc-plated spring steel wire. Clamshell packaging for display or resale.
Mfg. No.
OrderNo.
WireDia. In.
Fits HoleSize In.
OALIn.
Pkg.Qty.
30821 DHH30821 .062 5/64 1-5/16 930841 DHH30841 .093 7/64 2 1030850 DHH30850 .125 9/64 2-9/16 630860 DHH30860 .125 9/64 1-15/16 630870 DHH30870 .148 5/32 2-15/16 530880 DHH30880 .177 3/16 3-3/4 2
Hitchpin Clip Sets
Also known as hairpin clips.
Set ContentsKwic Kit – 11070 Kwic-Pak – 17070
Clip No.Wire
Sz. In. Qty.ClipNo.
WireSz. IN. Qty.
237 .054 25 237 .054 4225 .072 25 228 .093 4228 .093 12 216 .125 4211 .125 12 210 .148 3210 .148 4208 .177 2
Hitchpin SetsMfg. No.
OrderNo. Desc.
11070 DHH11070 80-pc. Kwic Kit17070 DHH17070 15-pc. Kwic-Pak
Cotter Pin SetsKwic-Pak
For agricultural, industrial and home use.
Set ContentsDimension Inches
Dia. x L Qty.3/32 x 1 10
3/32 x 1-1/2 101/8 x 1 5
1/8 x 1-1/2 55/32 x 1 4
5/32 x 1-1/2 43/16 x 1-1/2 4
3/16 x 2 41/4 x 2 2
5/16 x 2 2Cotter Pin Sets
Mfg. No. Order No. Desc.17010 DHH17010 50-pc. cotter pin Kwic-Pak
Woodruff Key SetsKwic Kit
Set Contents
No. Size In. Qty.#3 1/8 x 1/2 10#5 1/8 x 5/8 10#6 5/32 x 5/8 5#9 3/16 x 3/4 5#A 1/4 x 7/8 5#15 1/4 x 1 5
Woodruff Key Sets
Mfg. No. Order No. Desc.11110 DHH11110 40-pc. Kwic Kit
Safety ClipsStainless Steel
Non-corrosive, non-slip design. Replaces hairpin clips and cotter pins in many indus-trial uses. Carded.
Mfg. No.
OrderNo.
WireDia. In.
OALIn.
Pkg.Qty.
10282 DHH10282 1/8 2-1/2 2410290 DHH10290 5/32 3-3/4 24
2015 Catalog.indb 124 12/26/14 10:49 AM
125
Fasteners
ALASKA INDUSTRIAL HARDWARE, INC.
AIH Order Desk(907) 276-72011-800-478-7201www. .com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Hardware Caddies1000 pc. Hardware Assortment
For craft and household applications. In-cludes wood, sheet metal and machine screws, hex nuts, washers, picture hangers, pushpins/thumbtacks, nails, plastic anchors, cup hooks and two empty trays. 1000 pieces.
Mfg. No. Order No. Desc.W5199 WIM15899 Hardware caddy
E-Clip SetsKwic Kit
Set Contents
No. Size In. Qty.E-18 3/16 30E-25 1/4 30E-37 3/8 15E-50 1/2 10E-62 5/8 10E-75 3/4 5
E-Clip Sets
Mfg. No. Order No. Desc.11030 DHH11030 100-pc. Kwic Kit
Roll PinsAssortment
Includes varying lengths from 5/32" to 3/16".
Mfg. No. Order No. Pc. Qty.W5340 WIM15940 120
Hardware Assortments
WIM15900
WIM15905
WIM15910
WIM15912
WIM15914
WIM15915
Mfg. No.
Order No. Desc.
W5200 WIM15900 200-Pc. spring assortment
W5204 WIM15905 1000-Pc. copper pin assortment
W5210 WIM15910 150-Pc. hair pin assortment
W5212 WIM15912 300-Pc. snap ring assortment
W5214 WIM15914 125-Pc. rubber grommet assortment
W5215 WIM15915 70-Pc. grease fitting assortment
Fastener Assortments
Durable and reusable container. Contains enough items to complete multiple projects.
Mfg. No.
Order No. Desc.
14991 MFC14991 92 pc. hook & eye asst.14992 MFC14992 175 pc. picture hanger asst.14993 MFC14993 336 pc. handyman fastener asst14994 MFC14994 662 pc. household fastener asst.14995 MFC14995 1345 pc.nail/tack/brad asst.14997 MFC14997 235 pc. nut/washer asst.14998 MFC14998 221 pc. wood/sheet metal screw asst.14999 MFC14999 77 pc. anchor asst.
Snap Fastener Kits
Snap fasteners easily join two pieces of fab-ric. Kit includes a two-piece setting tool and six fastener sets.
Mfg. No. Order No. Desc.1265 GEN1265 Snap fastener kit
Screw Fastener Kits
Screw fasteners for attaching cover, tarps, and other fabrics. Kit includes a two-piece setting tool and six fastener sets.
Mfg. No. Order No. Desc.1267 GEN1267 Screw fastener kit
2015 Catalog.indb 125 12/26/14 10:49 AM
126
Fasteners
GHD Order Desk(907) 279-66911-800-478-4393
2192 VIKING DRIVEANCHORAGE, AK 99501
GENERAL HARDWAREDISTRUBUTORSwww.ghdalaska.com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
O-Ring Sets
32 sizes, from 1/16" x 1/4" to 1/8" x 2-1/4". Resealable plastic case.Mfg No. Order No. Desc.15902 WIM15902 407-Pc. O-ring assortment
Hollow Wall Anchors
For use in thin materials including wallboard, plaster and paneling. Prongs grip material, preventing rotation while anchor is being set. As screw is turned, anchor expands to se-cure itself against medium.
OrderNo.
AnchorSize In.
ScrewLgth. In.
HoleSize In.
Pkg.Qty.
Standard Machine Screw — 6-32 SizePFC26882 1/8 1-1/2 5/16 100PFC26880 1/8 2 5/16 100
Standard Machine Screw — 10-24 SizePFC26891 3/16 2-1/4 3/8 100PFC26889 3/16 2-3/4 3/8 100
Standard Machine Screw — 1/4 -20 SizePFC26878 1/4 2-1/4 1/2 100PFC26877 1/4 2-3/4 1/2 100
Drive Point Screw — 6-32 SizePFC26897 1/8 1-3/4 5/16 100PFC26896 1/8 2-11/32 5/16 100
Conical Plastic Anchors
For light-duty use in concrete, brick, masonry or drywall. Ridged plastic helps eliminate spinning while screw is being inserted.
Order No. Dia. In. Lgth. In. Pkg. Qty.PFC27816 3/16 7/8 100PFC01225 1/4 1 100PFC01202 5/16 1-3/8 100
Hollow Wall AnchorsDrillerToggle™
Self-drilling. Fast and easy to install with no pre-drilling required. Supplied with bolt. Rustproof. Suitable materials are drywall and baseboard.
Mfg. No. Order No. Desc. Pkg. Qty.023-01-2330-410 PFC82719 Zinc/Nylon 12
Hollow Wall AnchorsZip-Toggle®
The Zip-Toggle® is a self drilling hollow gypsum wallboard anchor designed to pro-vide superior performance without the need to pre-drill larger diameter holes. The Zip-Toggle is packaged with its own No. 6 x 2" lubricated screw.
Mfg. No. Order No. Desc. Pkg. Qty.2295 POW2295 Zinc 50
Wallboard AnchorsZip-It®
The Zip-It® anchor is a one piece self drilling anchor designed for use in hollow gypsum wallboard for light duty loads. Made from en-gineered nylon and for use with No. 6, 8 or 10 screws in 3/8" to 1" wallboard.
Mfg. No. Order No. Desc. Pkg. Qty.02345 POW02345 Nylon 10002346 POW02346 Metal 100
Drywall AnchorsScrew-In
#8 nylon. Mfg.No.
OrderNo. Desc.
Pkg. Qty.
02301-0807-410 PFC79621 Nylon anchor 2502301-0800-410 PFC80641 Zinc anchor 25
Plastic Anchor Kits
Includes one 4" carbide masonry drill bit.PFC27410: Set contains 50 blue plastic anchors and 100 1" combination phil-lips/slotted hardened sheet metal screws.PFC27360: Set contains 100 blue plastic anchors and 100 1" combination phil-lips/slotted hardened sheet metal screws.
Mfg.No.
OrderNo.
Drill Dia.In.
ScrewSize
02306-6810-400 PFC27410 3/16 #602306-1012-400 PFC27360 1/4 #10
2015 Catalog.indb 126 12/26/14 10:50 AM
127
Fasteners
ALASKA INDUSTRIAL HARDWARE, INC.
AIH Order Desk(907) 276-72011-800-478-7201www. .com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Toggle BoltsRound Head
For use in hollow wall, plaster, hollow tile and blocks. Zinc-plated.
Mfg.No.
OrderNo.
Dia.In.
Lgth.In.
HoleSize In.
Pkg.Qty.
00413-2024-411 PFC27467 1/8 2 3/8 10000413-2030-411 PFC27487 1/8 3 3/8 100
00413-2040-411 PFC27501 1/8 4 3/8 100
00413-2324-411 PFC27504 3/16 2 1/2 100
00413-2330-401 PFC18713 3/16 3 1/2 100
00413-2340-411 PFC27531 3/16 4 1/2 100
00413-2430-401 PFC27769 1/4 3 5/8 50
00413-2440-401 PFC18744 1/4 4 5/8 25
00413-2460-411 PFC27449 1/4 6 5/8 50
00413-2640-411 PFC27547 3/8 4 1 25
Toggle StrapsHollow Wall
4" hollow wall strap with carbon steel wing and locking cap. Can be installed through small holes. Does not require a fixture or screw to set. 50 per package.
Mfg. No. Order No. Dia. In.4052 POW4052 3/164054 POW4054 1/44056 POW4056 3/84058 POW4058 1/2
NOTES________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
NOTES________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________________
2015 Catalog.indb 127 12/26/14 10:50 AM
128
Fasteners
GHD Order Desk(907) 279-66911-800-478-4393
2192 VIKING DRIVEANCHORAGE, AK 99501
GENERAL HARDWAREDISTRUBUTORSwww.ghdalaska.com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Air/Hydraulic Riveters
For use in setting 3/32" to 3/16" diameter riv-ets. 1,940-lb. pulling force. .551" stroke.
Mfg. No. Order No. PSIV-2/79014 MAR79014 85 to 95
Rivet Tool Kits200 Kit™
Includes molded plastic case, HP-2® hand riveter and 200 Klik-Fast™ rivets in common sizes.
Mfg. No. Order No. Desc.39001-200 MAR39001 Hand riveter kit
Rivet ToolsBig Daddy®
Self-adjusting two-piece jaws. Single-unit steel body with extra-long handles and vinyl grips. Includes 5/32", 3/16" and 1/4" nose-pieces stored on body.
Mfg. No. Order No. Max. Rivet Size In.39031 HP-5 MAR39031 1/4
Rivet ToolsHP-2®
Aluminum body, carbon steel upper handle and thick vinyl grips. Includes 3/32", 1/8", 5/32" and 3/16" nosepieces and service wrench.
Mfg. No. Order No. Max. Rivet Size In.39000 HP-2 MAR39000 3/16
Rivet ToolsTwister™
Gun head rotates 360º to reach difficult ar-eas. Comfortable, hi-viz, non-slip vinyl grip with spring loaded handle for easy loading. Lock clip on handle for compact storage. Ex-tended nose for hard to get at places. Du-rable all steel construction. Uses rivets 3/32", 1/8", 5/32" and 3/16" diameter. Includes four nose pieces and wrench.
Mfg. No. Order No. Desc.RHT300 ARORHT300 Rivet tool w/ rotating head
Rivet Tools
Extended reach nose hard to get at places. Comfortable, hi-viz, non-slip vinyl grip. with spring loaded handle for easy loading. Lock clip on handle for compact storage. Durable all steel construction. Uses rivets 3/32", 1/8", 5/32" and 3/16" diameter. Includes four nose pieces and wrench.
Mfg. No. Order No. Desc.RH200S ARORH200S Rivet tool w/Extended nose
Rivet Tools
Durable all steel construction. Comfortable, hi-viz, non-slip vinyl grip. with spring loaded handle for easy loading. Changeable nose pieces take 1/8" and 5/32" diameter rivets in one hole and 3/16" in other hole. Not recom-mended for use with 3/16" all-steel rivets.
Mfg. No. Order No. Desc.RL100S ARORL100S Rivet tool
Rivets
Mfg.No.
OrderNo.
Dia.In.
Lgth.In.
Pkg.Qty.
Steel — Buttonhead40100 SB3-2 MAR40100 3/32 .250 50040102 SB3-4 MAR40102 3/32 .375 50040112 SB4-2 MAR40112 1/8 .275 50040115 SB4-3 MAR40115 1/8 .337 50040117 SB4-4 MAR40117 1/8 .400 50040120 SB4-5 MAR40120 1/8 .462 50040121 SB4-6 MAR40121 1/8 .525 50040122 SB4-8 MAR40122 1/8 .650 50040135 SB5-4 MAR40135 5/32 .425 50040136 SB5-6 MAR40136 5/32 .550 50040147 SB6-4 MAR40147 3/16 .450 50040149 SB6-6 MAR40149 3/16 .575 50040152 SB6-8 MAR40152 3/16 .700 500SB8-4 MAR42181 1/4 .250 100SB8-6 MAR42183 1/4 .275 100SB8-8 MAR42185 1/4 .500 100SB8-10 MAR42187 1/4 .625 100
Steel — Large Flange40150 SBL6-6 MAR40150 3/16 .575 50040153 SBL6-8 MAR40153 3/16 .700 50040156 SBL6-10 MAR40156 3/16 .825 50040160 SBL6-12 MAR40160 3/16 .950 500
Aluminum — Buttonhead43043 MAR43043 1/8 .275 50040212 AB4-2A MAR40212 1/8 .275 50040217 AB4-4A MAR40217 1/8 .400 50040220 AB4-5A MAR40220 1/8 .462 50040221 AB4-6A MAR40221 1/8 .525 50040222 AB4-8A MAR40222 1/8 .650 50040245 AB6-2A MAR40245 3/16 .325 50040247 AB6-4A MAR40247 3/16 .450 50040249 AB6-6A MAR40249 3/16 .575 50040252 AB6-8A MAR40252 3/16 .700 500AB8-6A MAR42283 1/4 .275 100AB8-8A MAR42285 1/4 .250 100AB8-12A MAR42289 1/4 .750 100
Aluminum — Large Flange40248 ABL6-4A MAR40248 3/16 .450 50040250 ABL6-6A MAR40250 3/16 .575 50040253 ABL6-8A MAR40253 3/16 .700 500
Stainless Steel
SSB4-4S MAR40417 3/16 .250 500SSB6-6S MAR40449 1/4 .375 500
2015 Catalog.indb 128 12/26/14 10:50 AM
129
Fasteners
ALASKA INDUSTRIAL HARDWARE, INC.
AIH Order Desk(907) 276-72011-800-478-7201www. .com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Rivets
Aluminum Steel
Mfg.No.
OrderNo.
RivetDia.In.
GripLgth.
In.Pkg.Qty. Size
AluminumRSA18 ARO00803 1/8 1/8 25 ShortRSA18IP ARO00820 1/8 1/8 100 ShortRSAW18IP* ARO00832 1/8 1/8 100 ShortRMA18 ARO00804 1/8 1/4 20 MediumRMA18IP ARO00821 1/8 1/4 100 MediumRLA18 ARO00805 1/8 1/2 15 LongRLA18IP ARO00822 1/8 1/2 100 LongRSA532 ARO00809 5/32 1/8 20 ShortRSA532IP ARO00826 5/32 1/8 50 ShortRMA532 ARO00810 5/32 1/4 20 MediumRMA532IP ARO00827 5/32 1/4 50 MediumRLA532 ARO00811 5/32 1/2 15 LongRLA532IP ARO00828 5/32 1/2 50 LongRSA316 ARO00812 3/16 1/8 18 ShortRSA316IP ARO00829 3/16 1/8 50 ShortRMA316 ARO00813 3/16 1/4 15 MediumRMA316IP ARO00830 3/16 1/4 50 MediumRLA316 ARO00814 3/16 1/2 12 LongRLA316IP ARO00831 3/16 1/2 50 LongRSAW18* ARO00815 1/8 1/8 25 Short
SteelRSS18 ARO00806 1/8 1/8 25 ShortRSS18IP ARO00823 1/8 1/8 100 ShortRMS18 ARO00807 1/8 1/4 20 MediumRMS18IP ARO00824 1/8 1/4 100 MediumRLS18 ARO00808 1/8 1/2 15 LongRLS18IP ARO00825 1/8 1/2 100 Long
* White
Flange RivetsLarge
For heavy duty jobs. Stainless steel con-struction. Not recommended for use with manual rivet tools.
Mfg. No. Order No. Dia. In.RLFA316IP ARO00888 3/16
Rivets
Assortment of 120 aluminum and steel rivets organized in divided shell.
ContentsSize In. Material Qty.
1/8 x 1/8 Aluminum 251/8 x 1/4 Aluminum 201/8 x 1/2 Aluminum 151/8 x 1/8 Steel 251/8 x 1/4 Steel 201/8 x 1/2 Steel 15
Rivets
Mfg. No. Order No. Desc.RK6120 ARO06120 Rivet assortment
Back-Up Washers
Round. .056" thick.
Mfg.No.
OrderNo.
SizeIn.
For HoleSize In.
Pkg.Qty.
Aluminum40657 AS-8 MAR40657 3/8 1/8 50040660 AS-10 MAR40660 1/2 3/16 500
Steel40661 SS-10 MAR40661 1/2 3/16 500
Washers
Mfg. No.
OrderNo.
HoleDia. In.
Qty.Pkg. Desc.
WA1/8 ARO00816 1/8 30 AluminumWS1/8 ARO00818 1/8 40 SteelWA3/16 ARO00817 3/16 30 Aluminum
Insert Installation KitsThread-Setter™
Includes No. 39200 Thread-Setter™ tool with mandrels and nosepieces for sizes 6-32, 8-32, 10-24; mandrel for size 1/4”-20; assort-ment of 103 Klik® Rivet-Nuts and Klik® Poly-Nuts. Packaged in plastic case with wrench and instructions.
Mfg. No. Order No. Desc.39301 MAR39301 Insert installation kit
Aluminum Rivet NutsKlik®
Flathead design. For use in metal, plastic and fiberglass too thin for tapped threads. Provides permanent captive threads for screws and bolts.
Mfg. No.
OrderNo.
ThreadSize
HeadDia. In.
Lgth.In.
Pkg.Qty.
47221 MAR47221 8 - 32 .337 .500 5047232 MAR47232 10 - 24 .406 .594 5047252 MAR47252 1/4" - 20 .475 .687 4047271 MAR47271 5/16" - 18 .665 .750 25
2015 Catalog.indb 129 12/26/14 10:50 AM
130
Fasteners
GHD Order Desk(907) 279-66911-800-478-4393
2192 VIKING DRIVEANCHORAGE, AK 99501
GENERAL HARDWAREDISTRUBUTORSwww.ghdalaska.com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Staple Guns
Jam resistant, double leverage operation. Vi-sual refill window. Steel construction, chrome finish. Accepts .050 guage staples of 1/4, 5/16, 3/8, 1/2 and 9/16" lengths plus CEILT-ILE® ceiling tile staples.
Mfg. No. Order No. Desc.T-50 AROT50 Staple gun
Staple/Brad Nail GunsHeavy Duty
Die-cast aluminum construction with ergo-nomic grip. Quick bottom load and Hi/Low power setting.
Mfg.No.
OrderNo.
Brad Nails Type
T50 Staples Dim. In.
T50RED AROT50RED 18ga. up to 1" 1/4 – 9/16
Staple/Brad Nail GunsT50®/BN1810™
The X Machine-Electric Pro™ staple and nail gun drives BN1810™ nails and six sizes of T50® staples. Visual refill window. Includes case.
Mfg. No. Order No. Volts AmpsETFX50 AROETFX50 115 14
Hammer Tackers
Jam resistant loading mechanism, precision-locked rear loading. Steel construction with rubberized grip. Accepts .050 guage staples 5/16, 3/8 and 1/2" lengths.
Mfg. No. Order No. Mag. Cap.HT-50 AROHT50 170
Hammer TackersProfessional
Steel construction, jam resistant mecha-nism. Recessed hand grip protects hand from scraping. Surface guard flange reduces damage to surface. Holds two full strips of Arrow staples.
Mfg. No. Order No. Desc. Staple Size In.HTX50 AROHTX50 T50 Stapler 5/16, 3/8, 1/2
StaplesT50®
Heavy duty staples. Ideal for use with Arrow®'s T50SA, T50SHA, ET50, ETN50, ETF50, & ETC50 staple guns and tackers. Also fits Ace®, Craftsman®, Master Mechan-ic®, Powershot®, and Stanley®.Mfg. No. Order No. Lgth. In. Pkg. Qty.504 ARO504 1/4 1250505 ARO505 5/16 1250506 ARO506 3/8 1250506SS* ARO506SS 3/8 1250508 ARO508 1/2 1250509 ARO509 9/16 1250505IP ARO505IP 5/16 5000506IP ARO506IP 3/8 5000
*Stainless steel staples.
StaplesHammer Tacker
Galvanized staples for hammer tackers. Use with Arrow® HT50A® stapler.
Mfg. No. Order No. Size In. Pkg. Qty.FANA1138G FAN10000 3/8 5000
Staple GunsJT-21™
Jam resistant mechanism, buit-in staple lifter. Visual refill window. Steel construction, chrome finish. Accepts 1/4, 5/16 and 3/8" staples.
Mfg. No. Order No. Desc.JT-21CM AROJT21CM Staple Gun
StaplesJT-21™
7/16" flat crown, light duty staples for use with Arrow® JT-21CM™, Powershot®, Easy-shot®, Easyfire®, Craftsman®, Ace®, Master-craft® and Stanley® staplers.
Mfg. No. Order No. Lgth. In. Pkg. Qty.
JT-21-1/4 ARO214 1/4 1000
JT-21-5/16 ARO215 5/16 1000
JT-21-3/8 ARO276 3/8 1000
2015 Catalog.indb 130 12/26/14 10:50 AM
131
Fasteners
ALASKA INDUSTRIAL HARDWARE, INC.
AIH Order Desk(907) 276-72011-800-478-7201www. .com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
Staple GunsT2025
For use with both round and flat crown sta-ples. Accepts 9/32, 3/8, 7/16 and 9/16" round staples as well as 5/16, 3/8 and 1/2" flat crown staples. Built-in staple height adjust-ment guide.
Mfg. No. Order No. Desc.T2025 AROT2025 Round & flat crown stapler
StaplesT2025™
5/16" flat crown staples for use with T2025 and ET2025 staple guns.
Mfg. No. Order No. Lgth. In. Pkg. Qty.
205 ARO205 5/16 1000
206 ARO206 3/8 1000
208 ARO208 1/2 1000
Wire TackersT-59™
Grooved guide. Jam resistant loading mech-anism. For low voltage wire up to 5/16" diam-eter. UL Listed
Mfg. No.
OrderNo.
Mag.Cap.
Max. WireSize In.
StapleLgth. In.
T-59 AROT59 30 5/16 5/16
StaplesT59™ — Insulated
Black, insulated 11/16" leg length. For wire up to 1/4" diameter. For use with Arrow T59 wire and cable tackers. UL listed.
Mfg. No. Order No. Lgth. In. Pkg. Qty.591188BL ARO59111 5/16 300
Wire TackersT-25™
Grooved guide. Jam resistant loading mech-anism. For low voltage wire up to 1/4" diam-eter. UL listed.
Mfg. No.
OrderNo.
Mag.Cap.
Max. Wire
Size In.Staple
Lgth.In.T-25 AROT25 85 1/4 9/32, 3/8, 716 and 9/16
Wire TrackersT25X™
Compact, ergonomic design. Simple load-ing and release mechanism. Grooved guide. Lightweight, quality plastic housing with du-rable steel components. Uses T25 staples.
Mfg. No.
Order No.
Mag.Cap.
Max Wire Size In.
Staple Lgth. In.
T25X AROT25X 85 9/16 3/8, 7/16, & 9/16
StaplesT25™
5/16" round crown staples for use with T25, T2025, CT2025, ET2025 wire and cable tackers.
Mfg. No. Order No. Lgth. In. Pkg. Qty.256 ARO256 3/8 1000257 ARO257 7/16 1000259 ARO259 9/16 1000
Wire TackersT-37™
All steel construction with grooved driving blade and jam resistant mechanism. Short span easy compression handle. Chrome fin-ish resists wear and tear. Grooved guide en-sures perfect stapling. For low voltage wire up to 5/16" diameter UL listed.
Mfg. No.
OrderNo.
Mag.Cap.
Max. WireSize In.
StapleLgth.In.
T-37 AROT37 85 3/8 3/8, 1/2 and 9/16
2015 Catalog.indb 131 12/26/14 10:50 AM
132
Fasteners
GHD Order Desk(907) 279-66911-800-478-4393
2192 VIKING DRIVEANCHORAGE, AK 99501
GENERAL HARDWAREDISTRUBUTORSwww.ghdalaska.com
ORDER ONLINE TODAY — SHIPS OUT TOMORROW!
StaplesT37™
3/8" round crown staples for use with Arrow® T37 Tacker, Powershot®, Craftsman®, Black & Decker®, Stanley® and Ace®.
Mfg. No. Order No. Lgth. In. Pkg. Qty.378 ARO378 1/2 1000
Plier-type StaplersHeavy Duty
All steel construction, chrome finish. Hand guide loop. Cam actuated double leverage mechanism. 2 1/2" throat for better reach Loads 1/4" and 3/8" staples.
Mfg. No. Order No. Mag. Cap.P-35 AROP35 85
StaplesP35™
7/16" flat crown, heavy duty staples for use with Arrow® P35 plier-type stapler.
Mfg. No. Order No. Lgth. In. Pkg. Qty.354 ARO354 1/4 5000356 ARO356 3/8 5000
Hammer TackersClassic — Duo-Fast®
Features rear-loading magazine with two-strip capacity, and fast jam clearance. Ac-cepts 20 ga., 1/2" crown staples 5/32" to 5/16" long (includes 1 box). Excellent for sta-pling carpet pads.
Mfg. No. Order No. Dim. In. H x W x LHT-550/1013292 DUO77047 3-1/4 x 1-3/8 x 11-3/8
Staples1/2" Crown — Duo-Fast®
20 ga., .050" wire construction with chisel point and galvanized finish.
Mfg. No. Order No. Lgth. In. Pkg. Qty.5008C 1/4"/3947 DUO03947 1/4 50005010C 5/16" 4291 DUO04291 5/16 50005012C 3/8"/4739 DUO04739 3/8 50005016C 1/2"/5223 DUO05223 1/2 5000
Manual Collated Ring Pliers
Automatic feed, one hand operation. Uses 11/16" 16 guage C-rings.
Mfg. No. Order No. Desc.P7 BSTP7 Max. cap. 50 rings
StaplesC-Ring
For use with bostich BSTP7 manual collated ring pliers.
Mfg. No. Order No. Lgth In. Pkg. Qty.RING616G50B BST4085 11/16 2500
StaplesHeavy Duty
Heavy duty staples for use in Stanley-Bostitch® staplers.
Mfg. No. Order No. Lgth. In. Pkg. Qty.586 ARO586 3/8 1000
Divergent Point Staples3/16" Crown — Duo-Fast®
20 ga. Designed for improved holding power, easier driving and reduced staple gun mis-fires. Galvanized steel construction.
Mfg. No. Order No. Lgth. In. Pkg. Qty.5418D/7740 DUO07740 9/16 5000
Hog Ringer Pliers
For closing hog rings and ring fasteners. Malleable cast iron construction. Zinc-plated.
Mfg. No. Order No. Use WithRR-HM SEYRRHM Hill H1, H2, H3, PBH1, PBH2,
PBH3, B1, B2 and B3 rings
Pig & Hog RingsCopper-coated 12.5 ga. steel wire. De-signed to prevent swine from rooting in ground. Hill pattern; closes in triangular shape. Slant point. 100 per box.
Mfg. No. Order No. Desc.RN-H1 SEYRNH1 Pig ringsRN-H3 SEYRNH3 Hog rings
2015 Catalog.indb 132 12/26/14 10:50 AM