Appendix-11
GUARANTEED TECHNEAI INO Ornrn panTl FoR rHE suPPlY OII]NEIEJ
MULTIPLE CORE LT XLPE ARMOURED qAI]LES.
Sr.
No.
Particutars Singte / Muttipte Core XLPE
Armoured Cables
Sizes
1 Manufacturer's name and works address
7. Standard specification to which the materiat shatt conform
3. Vottage Grade
4. No. of Cores
5. Conductor detaits:
A Normal cross section area of
1 Phase Conductor (mm2)
2 Neutral Conductor (mm')
B No. and size of strands (in mm) of :
1 Phase Conductor (mm2;
2 Neutral Conductor (mm')
C Shape of Conductor
D Whether compacted or non-compacted
E Resistance al27"C
1 Phase Conductor ( ohm/km)
z NeutraI Conductor (ohm/km)
6. lnsutation
1 Type
2 Cotour
3 Thickness
A Phase Conductor ( ohm/km)
1 Nominal (mm)
2 Minimum (mm)
B Neutrat Conductor (Sq. mm)
1 Nominat (mm)
2 Minimum (mm)
7. Type of inner sheathing and cotour
B. Whether Binder Tape provided
9. Armoring
A Type
B Dimension (mm)
10. Outer Sheatlr
MateriaI
B Thickness
1 Nominat (mn )
2 Minimum (m n)
C Standard to whi< n it confirm
11 A Type and size of fitter used
B Min. welght of F ttpr in kgi km
17. Max. overatl diamete )f the cabte (in mm)
13. Nature of Packing.
14. DRUM
A Tare weight of I n1
B Whether Drum i rheeI
L Standard specific )n to which it confornrs
lo Drum details & dimensions
FWhetne, 2-Futt Pty Ftange Construction or 2-Fut[
Ptv ptus 1 Segmentat tayer Ftange Construction'
F Drum size
1 Flange Diameter (d1) (mm)
?. Barrel Diameter (d2) (mm)
)J Centre hote Diameter (d3) (mm)
4 Overatl with (11) (mm)
5 Travers (L2) (mm)l-IG Detaits of Wooden ComPonent
1 Thickness of Ftange Main Disc) (mm)
7 garrel End (Supporting disc or Core Segment)
a) Diameter (mm)
b) Thickness (mm)
3 Stretchers (Core Carrier Ptanks )
a) Number (Min)
b) Thickness x width (mm)
4 Aarret Battens (Core Fitter Planks) Thickness
(rnm)
5 Barrel Middte Supports (Middte Core Disc)
H
I
Thickness of Externat Lagging (mm)
Details of Metal
1 Ctamping Studs with Hexagonal Nuts
a) Numbers
b) Diameter (mm)
1 Square or Round Washers
a) Numbers
b) Diameter (mm)
3 Mitd Steet Bushes
a) Numbers
b) Thickness of Steeve (mm)
c) Dimension of Sleeve (mm
d) Number of Botts
e) Diameters of Botts
4 Mitd Steet/Cast lron Centre Ptate
a) Numbers
b) Diameter of Botts (mm)
c) Centre Plate Botts.
d) Numbers
i) Diameter of Bolts (mm)
ii) Centre Hote Diameter (mm)
15. Minimum Weight in kg/km
,A Aluminium
D XLPE
C PVC
16. Standard Length of cabte in meter & its toterance
17. Whether materia[ bears BIS Certification
18. BIS License no.& vatiditY
19. Embossing.
70. Any other particutars.