Pneumatic Fittings& Tubing

105646 © 1999 Dayco Products, Inc.

Dayco Products, Inc.1 Prestige PlaceP.O.Box 1004Dayton, OH 45401-1004

Distributed BY:

Tube Max. Recom.Tube Wall Min. Bend Working Min. BurstO.D. Thickness Radius Pressure Pressure

Style (Inches) (Inches) (Inches) (PSI) (PSI) Fittings

Poly-Flo® 1/8 .020 1/2 125 500 Poly-Flo®

(Polyethylene) 5/32 .025 5/8 125 500 Poly-Flo® Kwik-Connect Couplings (1/4 & 3/8 O.D.)P 3/16 .030 3/4 125 500

PE 1/4 .040 1 100 4005/16 .062 1 1/8 150 6003/8 .062 1 1/4 90 3501/2 .062 2 1/2 65 250

Impolene 1/8 .023 1/2 225 900 Poly-Flo® with 261UB Universal Nut & Sleeve(Polyallomar) 3/16 .034 3/4 225 900 Poly-Flo® Kwik-Connect Couplings (1/4 & 3/8

PP 1/4 .040 1 225 900 O.D.) with 261UB Universal Nut & SleevePY 3/8 .062 1 1/4 225 900

1/2 .062 2 1/2 188 750

Nylo-Seal® 1/8 .017 1/2 375 1500 Poly-Flo® with 261UB Universal Nut & Sleeve(Nylon 11) 5/32 .022 5/8 375 1500 Poly-Flo® Kwik-Connect Couplings (1/4 & 3/8

SN 3/16 .024 3/4 375 1500 O.D.) with 261UB Universal Nut & SleeveNT 1/4 .033 1 375 1500 OmegaFlo®

5/16 .040 1 1/2 375 1500 Hi-Duty®*3/8 .048 1 3/4 375 1500 Hi-Seal®*1/2 .062 2 3/8 375 1500

Nylo-Seal® 1/8 .026 3/8 625 2500 Poly-Flo® (1/8 & 3/16 O.D. only) with 261UB(Nylon 11) 3/16 .039 5/8 625 2500 Universal Nut & Sleeve

NSR 1/4 .050 7/8 625 2500 OmegaFlo®

3/8 .075 1 1/2 625 2500 Hi-Duty®*1/2 .075 2 1/2 500 2000 Hi-Seal®*

Nylo-Seal® 1/8 .023 3/8 250 1000 Poly-Flo® with 261UB Universal Nut & Sleeve(Nylon 11) 5/32 .024 1/2 250 1000 Poly-Flo® Kwik-Connect Couplings (1/4 & 3/8 O.D.)

NF 3/16 .024 5/8 250 1000 OmegaFlo®

1/4 .033 7/8 250 1000 Hi-Duty®*1/4 .040 1/2 300 1200 Hi-Seal®*5/16 .040 1 1/4 250 10003/8 .048 1 1/2 250 10003/8 .060 3/4 300 12001/2 .062 2 250 1000

Polyvinyl 1/4 .040 1/2 50 200 Poly-Flo®

Chloride 3/8 .062 1 40 160 Poly-Flo® Kwik-Connect Couplings (1/4 & 3/8 O.D.)PVC 1/2 .062 2 35 140

Poly-Flo® 1/4 .040 1 100 400 Poly-Flo®

Flame Retardant 3/8 .062 1 1/4 88 350 Poly-Flo® Kwik-Connect Couplings (1/4 & 3/8 O.D.)1/2 .062 2 1/2 63 250

General InformationThermoplastic Tubing/Fitting Reference Guide

*Consult factory for further information.1 Insert must be used with SN tubing when temperature exceeds 180˚ F and with NF tubing under all temperature conditions.2 Insert must be used with Poly-Flo® tubing under all temperature conditions.

General InformationMetal Tubing/Fitting Reference Guide

MaximumTube OperatingSize Tube Pressure

Tubing O.D. Wall (PSI) Fittings

1/8 .030 43003/16 .030 28501/4 .030 2100

COPPER 5/16 .032 1800 Hi-Duty®

DEAD SOFT 3/8 .032 1500 45˚ FlareSEAMLESS 1/2 .032 1150 Hi-Seal® BrassASTM B75 5/8 .035 1000ANSI H23.3 3/4 .035 850

7/8 .035 650

1/8 .030 4003/16 .030 400 Compresamatic™

COPPER 1/4 .030 300 CompressionDEAD SOFT 5/16 .032 300 Omega FloSEAMLESS 3/8 .032 500 Poly-Flo® with Universal Sleeve*ASTM B75 1/2 .032 200 Poly-Flo® Kwik-Connect Couplings*ANSI H23.3 5/8 .035 150 (1/4 & 3/8 O.D.) with 261UB

3/4 .035 150 Universal Nut & Sleeve

Tube TubingSize Tube Not Tubing

Tubing O.D. Wall Belled Belled Fittings

1/8 .030 1000 20003/16 .030 750 1500

COPPER 1/4 .030 500 1000DEAD SOFT 5/16 .030 500 1000SEAMLESS 3/8 .032 350 700ASTM B75 1/2 .032 200 500 Flex®

ANSI H23.3 5/8 .035 4003/4 .035 3507/8 .035 300

1/8 .062 3000COPPER PIPE 1/4 .082 3000RED BRASS 3/8 .090 3000 Brass Pipe*ASTM B43 1/2 .107 2000

1/8 .028 4600STEEL 3/16 .028 4000

COPPER 1/4 .034 3600BRAZED 5/16 .034 2750 45˚ Flare(BUNDY) 3/8 .042 2500

ASTM A254 1/2 .049 2250DOUBLE LAP FLARE 5/8 .049 2100

1/8 .028 60503/16 .028 41801/4 .035 3800

5/16 .035 3340STEEL 3/8 .049 3960

SEAMLESS 1/2 .049 2900SAE J524 5/8 .049 2280 Hi-Seal® Steel*WELDED 3/4 .049 1880SAE J525 7/8 .065 2150

1 .065 18601 1/4 .083 19201 1/2 .083 1580

Tube Type TypeSize Tube 316 17-4 PH

Tubing O.D. Wall Sleeves Sleeves Fitting

1/8 .028 8180 8180STAINLESS 3/16 .028 5650 5650

STEEL 1/4 .035 5900 5900ANNEALED 3/8 .049 5500 5500SEAMLESS 1/2 .049 4100 4100TYPE 304 5/8 .049 3300 3300 Hi-Seal® Stainless Steel*

ASTM A213 3/4 .049 2700 27001 .065 2510

1 1/4 .083 25801 1/2 .083 2130

* Consult factory for further information.

2

General InformationFitting Descriptions

Working PressureStyle Maximum Nominal Construction Application Compatible Tubing

Poly-Flo® 500 PSI 125 PSI • Three-piece: body, nut • Pneumatic instrumentation • Polyethylenesleeve circuits • Polypropylene

• Shapes: brass, forged • Fluid piping systems • NylonSAE CA377 or equal • Polyvinyl chloride

• Straights: brass, SAE • PolyallomarCA360 or equal • Soft metal

• Sleeves: Celcon® or • Poly-Flo®

Brass • Nylo-Seal®

(SN, NF)• Impolene

Poly-Flo® 500 PSI 125 PSI • Body and nuts: Chrome- • Low pressure instrumentation • PolyethyleneKwik-Connect plated brass or Type 316 lines requiring frequent • Polypropylene

stainless steel connecting and disconnecting • Nylon• Sleeves: Celcon® • Medical and dental equipment • Polyvinyl chloride• Springs: Stainless steel • Polyallomar• O-Rings: Buna N on brass • Soft copper

couplings, Viton® on • Poly-Flo®

stainless steel couplings • Nylo-Seal®

• Impolene

OmegaFlo™ 300 PSI 125 PSI • One-piece unit • Pneumatic instrumentation • Polyethylene• Shapes: brass, forged circuits • Nylon 11

SAE CA377 or equal • Fluid piping systems • Soft copper• Sleeves: SAE CA360 • Poly-Flo®

or equal • Nylo-Seal®

• Straights: brass SAE • ImpoleneCA360 or equal

Hi-Duty® 4,300 PSIA 800 PSI • Two piece: body and • Instrumentation systems • Coppernut/sleeve • Mobile farm and mobile • Brass

• Shapes: brass, forged SAE construction equipment • Seamless steelCA360 or equal • Hydraulic and pneumatic • Thermoplastic

• Flareless compression controlsdesign • Process control systems

• Laboratory equipment

Flex® 1,000 PSIA 200 PSI • Three piece: body, nut • High vibration and • Copperand elastomeric sleeve shock conditions • Brass

• Shapes: brass, forged • Diesel engine fuel lines • AluminumSAE CA377 or equal • Lubrication systems • Steel

• Straights: brass, SAE • Gasoline, air and • GlassCA360 or equal water lines • Thermoplastic

• Flareless• Special compound sleeves

available to 450˚F

Compression 400 PSIA 250 PSI • Three-piece: body, nut • Low pressure air, oil, • Copperand sleeve water and gas piping • Brass

• Shapes: brass, forged • Meets SAE J512 • AluminumSAE CA377 or equal • Thermoplastic

• Straights: brass, SAECA360 or equal

CompresaMatic™ 4,500 PSIA 850 PSI • Two-piece: body and • Air, oil, water and • Coppernut/sleeve gas piping • Brass

• Shapes: brass, forged • Meets SAE J512 • AluminumSAE CA377 or equal Except for the • Thermoplastic

• Straights: brass, SAE nut and sleeve • Seamless steelCA360 or equal

• Nuts and sleevesinterchangeable withstandard compressionbodies

AMaximum working pressure based on 1/8” O.D. dead soft copper tubing. Please consult Imperial Eastman for additional information.

TUBE SIZE (O.D.)

“Dash” No. – 02 – 03 – 04 – 05 – 06 – 07 – 08 – 10 – 12 – 14 – 16FITTINGS Size 1/8” 3/16” 1/4” 5/16” 3/8” 7/16” 1/2” 5/8” 3/4” 7/8” 1”

TUBE END THREADS

Hi-Duty® 5/16-24 3/8-24 7/16-24 1/2-20 9/16-20 11/16-16 7/8-18 1-18 1 1/4-18

45˚ Flare 5/16-24 3/8-24 7/16-20 1/2-20 5/8-18 11/16-16 3/4-16 7/8-14 1 1/16-14 1 1/4-12

CompresaMatic® 5/16-24 3/8-24 7/16-24 1/2-24 9/16-24 5/8-24 11/16-20 13/16-18 1-18

Compression 5/16-24 3/8-24 7/16-24 1/2-24 9/16-24 5/8-24 11/16-20 13/16-18 1-18

Flex® 3/8-24 7/16-24 1/2-24 9/16-24 5/8-24 13/16-18 1-18 1 1/8-18

Poly-Flo® andKwik-Connect 5/16-24 3/8-24 3/8-24 7/16-24 1/2-24 11/16-20

PIPE END THREADS

Pipe Fittings 1/8-27 1/4-18 3/8-18 1/2-14 3/4-14 1-111/2

7

General InformationThread Size Chart

Use this chart to determine fitting thread sizes per tube O.D.size.For example: Thread sizes for a Hi-Duty® 1/8” fitting, withPart No. 88LB02X02 are. . .5/16-24 tube thread size x 1/8-27pipe thread size, as below:

Fitting Style

Tube O.D.

Pipe size

88LB 02 X 02

PART NUMBER = 88LB02X02

8

General InformationAssembly Instructions

Fitting To Assemble To Reconnect

Hi-Duty® 1. Using a tube cutter, cut tube squarely and cleanly, 1. Reinsert tubingFlareless removing all burrs. 2. Tighten nut one eighth of a turn moreTube Fittings 2. Grasp fitting. Do not remove nut. than previous make-up.

3. Insert tube in fitting through nut until tube seats firmly NOTE: The Hi-Duty® fitting can beagainst tube shoulder in body. disconnected and reconnected repeatedly

4. Grip tube firmly to prevent turning and tighten nut until and will always reconnect tightly.a slight “give” is felt. This “give” indicates the sleevehas been sheared from the nut.

5. Continue tightening for one and one-half additionalturns for a positive, leakproof seal. It is not necessaryto tighten the nut all the way down.

45˚ Flare 1. Using a tube cutter, cut tubing squarely and cleanly, 1. Tighten to original make-up position, plusTube Fittings removing all burrs. an additional one-sixth turn of the nut

2. Slide nut onto tubing with the open threaded end of (one flat of the hex).the nut facing toward the end to be flared.

3. Flare tubing end with a good quality flaring tool.4. Position the flare against the nose of the fitting body

and align the tube with the fitting.5. Assemble nut to body, tightening finger tight.6. Tighten nut with a wrench one-quarter to one-half

turn for a leakproof connection.

Compression 1. Using a tube cutter, cut tube squarely and cleanly, 1. Tighten to original make-up position, plusFlareless Tube removing all burrs. an additional one-sixth turn of the nut Fittings 2. Insert tubing into the fitting body until it rests against (one flat of the hex).

the shoulder.3. Move sleeve into position and tighten the nut.

NOTE: No flaring, soldering or other special preparationof the tubing is necessary before assembly.

CompresaMatic™ 1. Using a tube cutter, cut tube squarely and cleanly, 1. Tighten to original make-up position, plusremoving all burrs. an additional one sixth turn of the nut

2. Insert the tube into fitting. Be sure the tube “bottoms” (one flat of the hex).on the fitting shoulder.

3. Tighten (hand-tight), and complete the seal with onewrench turn on all sizes.

Poly-Flo® 1. Using a tube cutter, cut tubing squarely and cleanly, 1. Tighten nut to original make-up position,Flareless removing all burrs. tightening finger tight.Tube Fittings 2. Push tubing into fitting and tighten the nut.

NOTE: There is no need to disassemble the fittingbefore assembly. When used with Poly-Flo® or PVCtubing, fitting is assembled finger tight. No wrenchesneeded.

Poly-Flo® 1. Using a tube cutter, cut tubing squarely and cleanly, 1. Tighten nut to original make-up position,Kwik-Connect removing all burrs. tightening finger tight.Couplers 2. Push tubing into fitting and tighten the nut.

NOTE: There is no need to disassemble the fittingbefore assembly. When used with Poly-Flo® or PVCtubing, assembly is finger tight.

OmegaFlo™ 1. Using a tube cutter, cut tubing cleanly and squarely. 1. Firmly push tubing into the fitting until itPush-to-Connect/ 2. Firmly push the tubing into the fitting until it will enter will enter no further. A properly assembledPush-to-Release no further. A properly assembled tube cannot be pulled tube cannot be pulled out by hand.Pneumatic out by hand.Fittings 3. To disconnect, simply push back on the brass collet

and release tubing.

33

Tube FittingsPoly-Flo® Kwik-Connect Couplers Material: Brass Finish: Chrome-Plated

WrenchPart Tube Pipe Bulkhead Pad/Hex

Style No. O.D. Thread Thread A B C D

294PM04 1/4 1/2-24 1.636 0.500294PM06 3/8 11/16-24 1.738 0.500

294PD04 1/4 1/2-24 3.180 1.790 0.625294PD06 3/8 11/16-24 3.458 1.965 0.812

294PB04 1/4 1/2-24 1.790 0.625294PB06 3/8 11/16-24 1.965 0.812

294P04 1/4 1/2-24 2.899 1.718 0.625294P06 3/8 11/16-24 3.461 1.921 0.812

STYLE 294PCouplerSingle End Shut-Off

STYLE 294PBBodyDouble End Shut-Off

STYLE 294PDCouplerDouble End Shut-Off

STYLE 294PMInsert (Without Shut-Off. Used on dou-ble end shut-off models)

B

A

C

A

C

B

A

C

A

C

34

Tube Fittings

Wrench WrenchPart Tube Pipe Pad/Hex Pad/Hex

Style No. O.D. Thread A B C D

298PD04X02 1/4 1/8 2.802 1.260 0.500 0.500298PD04X04 1/4 1/4 2.824 1.260 0.500 0.562298PD06X04 3/8 1/4 2.962 1.400 0.500 0.625

298PT04X02 1/4 1/8 1.260 0.500298PT04X04 1/4 1/4 1.260 0.562298PT06X04 3/8 1/4 1.400 0.625

298P04X02 1/4 1/8 2.261 1.260 0.500 0.500298P04X04 1/4 1/4 2.261 1.260 0.500 0.562298P06X04 3/8 1/4 2.323 1.400 0.500 0.625

294PMD04 1/4 1.787 0.500294PMD06 3/8 1.972 0.500

STYLE 294PMDInsert (With Shut-Off. Used on doubleend shut-off models)

STYLE 298PCouplerSingle End Shut-Off

STYLE 298PDCouplerDouble End Shut-Off

STYLE 298PTBody with Shut-Off(Standard on both double and single shut-off models)

A

C

B

A

CD

B

A

CD

A

C

Poly-Flo® Kwik-Connect Couplers Material: Brass Finish: Chrome-Plated

35

Tube FittingsPoly-Flo® Kwik-Connect Couplers Material: Stainless Steel

Wrench WrenchPart Tube Pipe Bulkhead Pad/Hex Pad/Hex

Style No. O.D. Thread Thread A B C D

294PSS04 1/4 1/2-24 2.899 1.718 0.625294PSS06 3/8 11/16-24 3.461 1.921 0.812

` 294PMSSD04 1/4 1.787 0.500294PMSSD06 3/8 1.972 0.500

294PMSS04 1/4 1.636 0.500294PMSS06 3/8 1.738 0.500

294PBSS04 1/4 1/2-24 1.790 0.625294PBSS06 3/8 11/16-24 1.965 0.812

STYLE 294PBSSBodySingle End Shut-Off

STYLE 294PMSSInsertSingle End Shut-Off

STYLE 294PMSSDInsertDouble End Shut-Off

STYLE 294PSSCouplerSingle End Shut-Off

A

C

A

C

A

C

B

A

C

36

Tube FittingsPoly-Flo® Kwik-Connect Couplers Material: Stainless Steel

Wrench WrenchPart Tube Pipe Bulkhead Pad/Hex Pad/Hex

Style No. O.D. Thread Thread A B C D

298PSSD04X02 1/4 1/8 2.802 1.260 0.500 0.500298PSSD04X04 1/4 1/4 2.824 1.260 0.500 0.562298PSSD06X04 3/8 1/4 2.962 1.400 0.500 0.625

298PTSS04X02 1/4 1/8 1.260 0.500298PTSS04X04 1/4 1/4 1.260 0.562298PTSS06X04 3/8 1/4 1.400 0.625

298PSS04X02 1/4 1/8 2.261 1.260 0.500 0.500298PSS04X04 1/4 1/4 2.261 1.260 0.500 0.562298PSS06X04 3/8 1/4 2.323 1.400 0.500 0.625

294PSSD04 1/4 1/2-24 3.180 1.790 0.625294PSSD06 3/8 11/16-24 3.458 1.965 0.812

STYLE 294PSSDCouplerDouble End Shut-Off

STYLE 298PSSCouplerSingle End Shut-Off

STYLE 298PSSDCouplerDouble End Shut-Off

STYLE 298PTSSBody with Shut-Off(Standard on both double and single shut-offmodels)

B

A

C

A

CD

B

A

CD

B

A

C

Tube Max. Recom.Tube Wall Min. Bend Working Min. BurstO.D. Thickness Radius Pressure Pressure

Style (Inches) (Inches) (Inches) (PSI) (PSI) Fittings

Poly-Flo® 1/8 .020 1/2 125 500 Poly-Flo®

(Polyethylene) 5/32 .025 5/8 125 500 Poly-Flo® Kwik-Connect Couplings (1/4 & 3/8 O.D.)P 3/16 .030 3/4 125 500

PE 1/4 .040 1 100 4005/16 .062 1 1/8 150 6003/8 .062 1 1/4 90 3501/2 .062 2 1/2 65 250

Impolene 1/8 .023 1/2 225 900 Poly-Flo® with 261UB Universal Nut & Sleeve(Polyallomar) 3/16 .034 3/4 225 900 Poly-Flo® Kwik-Connect Couplings (1/4 & 3/8

PP 1/4 .040 1 225 900 O.D.) with 261UB Universal Nut & SleevePY 3/8 .062 1 1/4 225 900

1/2 .062 2 1/2 188 750

Nylo-Seal® 1/8 .017 1/2 375 1500 Poly-Flo® with 261UB Universal Nut & Sleeve(Nylon 11) 5/32 .022 5/8 375 1500 Poly-Flo® Kwik-Connect Couplings (1/4 & 3/8

SN 3/16 .024 3/4 375 1500 O.D.) with 261UB Universal Nut & SleeveNT 1/4 .033 1 375 1500 OmegaFlo®

5/16 .040 1 1/2 375 1500 Hi-Duty®*3/8 .048 1 3/4 375 1500 Hi-Seal®*1/2 .062 2 3/8 375 1500

Nylo-Seal® 1/8 .026 3/8 625 2500 Poly-Flo® (1/8 & 3/16 O.D. only) with 261UB(Nylon 11) 3/16 .039 5/8 625 2500 Universal Nut & Sleeve

NSR 1/4 .050 7/8 625 2500 OmegaFlo®

3/8 .075 1 1/2 625 2500 Hi-Duty®*1/2 .075 2 1/2 500 2000 Hi-Seal®*

Nylo-Seal® 1/8 .023 3/8 250 1000 Poly-Flo® with 261UB Universal Nut & Sleeve(Nylon 11) 5/32 .024 1/2 250 1000 Poly-Flo® Kwik-Connect Couplings (1/4 & 3/8 O.D.)

NF 3/16 .024 5/8 250 1000 OmegaFlo®

1/4 .033 7/8 250 1000 Hi-Duty®*1/4 .040 1/2 300 1200 Hi-Seal®*5/16 .040 1 1/4 250 10003/8 .048 1 1/2 250 10003/8 .060 3/4 300 12001/2 .062 2 250 1000

Polyvinyl 1/4 .040 1/2 50 200 Poly-Flo®

Chloride 3/8 .062 1 40 160 Poly-Flo® Kwik-Connect Couplings (1/4 & 3/8 O.D.)PVC 1/2 .062 2 35 140

Poly-Flo® 1/4 .040 1 100 400 Poly-Flo®

Flame Retardant 3/8 .062 1 1/4 88 350 Poly-Flo® Kwik-Connect Couplings (1/4 & 3/8 O.D.)1/2 .062 2 1/2 63 250

General InformationThermoplastic Tubing/Fitting Reference Guide

*Consult factory for further information.1 Insert must be used with SN tubing when temperature exceeds 180˚ F and with NF tubing under all temperature conditions.2 Insert must be used with Poly-Flo® tubing under all temperature conditions.

General InformationMetal Tubing/Fitting Reference Guide

MaximumTube OperatingSize Tube Pressure

Tubing O.D. Wall (PSI) Fittings

1/8 .030 43003/16 .030 28501/4 .030 2100

COPPER 5/16 .032 1800 Hi-Duty®

DEAD SOFT 3/8 .032 1500 45˚ FlareSEAMLESS 1/2 .032 1150 Hi-Seal® BrassASTM B75 5/8 .035 1000ANSI H23.3 3/4 .035 850

7/8 .035 650

1/8 .030 4003/16 .030 400 Compresamatic™

COPPER 1/4 .030 300 CompressionDEAD SOFT 5/16 .032 300 Omega FloSEAMLESS 3/8 .032 500 Poly-Flo® with Universal Sleeve*ASTM B75 1/2 .032 200 Poly-Flo® Kwik-Connect Couplings*ANSI H23.3 5/8 .035 150 (1/4 & 3/8 O.D.) with 261UB

3/4 .035 150 Universal Nut & Sleeve

Tube TubingSize Tube Not Tubing

Tubing O.D. Wall Belled Belled Fittings

1/8 .030 1000 20003/16 .030 750 1500

COPPER 1/4 .030 500 1000DEAD SOFT 5/16 .030 500 1000SEAMLESS 3/8 .032 350 700ASTM B75 1/2 .032 200 500 Flex®

ANSI H23.3 5/8 .035 4003/4 .035 3507/8 .035 300

1/8 .062 3000COPPER PIPE 1/4 .082 3000RED BRASS 3/8 .090 3000 Brass Pipe*ASTM B43 1/2 .107 2000

1/8 .028 4600STEEL 3/16 .028 4000

COPPER 1/4 .034 3600BRAZED 5/16 .034 2750 45˚ Flare(BUNDY) 3/8 .042 2500

ASTM A254 1/2 .049 2250DOUBLE LAP FLARE 5/8 .049 2100

1/8 .028 60503/16 .028 41801/4 .035 3800

5/16 .035 3340STEEL 3/8 .049 3960

SEAMLESS 1/2 .049 2900SAE J524 5/8 .049 2280 Hi-Seal® Steel*WELDED 3/4 .049 1880SAE J525 7/8 .065 2150

1 .065 18601 1/4 .083 19201 1/2 .083 1580

Tube Type TypeSize Tube 316 17-4 PH

Tubing O.D. Wall Sleeves Sleeves Fitting

1/8 .028 8180 8180STAINLESS 3/16 .028 5650 5650

STEEL 1/4 .035 5900 5900ANNEALED 3/8 .049 5500 5500SEAMLESS 1/2 .049 4100 4100TYPE 304 5/8 .049 3300 3300 Hi-Seal® Stainless Steel*

ASTM A213 3/4 .049 2700 27001 .065 2510

1 1/4 .083 25801 1/2 .083 2130

* Consult factory for further information.