04_FPH800_R2-5_EPD

8/10/2019 04_FPH800_R2-5_EPD

1/22

Issued in 2010 Nokia Siemens Networks 1 (22)

FlexiPacket Hub 800 R2.5

Environmental ProductDeclaration

Issue:1 Issue date: Mar 2013A25000-A0800-E071-01-76P1

8/10/2019 04_FPH800_R2-5_EPD

2/22

Environmental Product Declaration

2 (22) Nokia Siemens Networks Issued in 2012

The information in this document is subject to change without notice and describes only theproduct defined in the introduction of this documentation. This documentation is intended forthe use of Nokia Siemens Networks customers only for the purposes of the agreement underwhich the document is submitted, and no part of it may be used, reproduced, modified or

transmitted in any form or means without the prior written permission of Nokia SiemensNetworks. The documentation has been prepared to be used by professional and properlytrained personnel, and the customer assumes full responsibility when using it. Nokia SiemensNetworks welcomes customer comments as part of the process of continuous developmentand improvement of the documentation.

The information or statements given in this documentation concerning the suitability, capacity,or performance of the mentioned hardware or software products are given as is and allliability arising in connection with such hardware or software products shall be definedconclusively and finally in a separate agreement between Nokia Siemens Networks and thecustomer. However, Nokia Siemens Networks has made all reasonable efforts to ensure thatthe instructions contained in the document are adequate and free of material errors andomissions. Nokia Siemens Networks will, if deemed necessary by Nokia Siemens Networks,explain issues which may not be covered by the document.

Nokia Siemens Networks will correct errors in this documentation as soon as possible. IN NOEVENT WILL NOKIA SIEMENS NETWORKS BE LIABLE FOR ERRORS IN THISDOCUMENTATION OR FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TOSPECIAL, DIRECT, INDIRECT, INCIDENTAL OR CONSEQUENTIAL OR ANY LOSSES,SUCH AS BUT NOT LIMITED TO LOSS OF PROFIT, REVENUE, BUSINESSINTERRUPTION, BUSINESS OPPORTUNITY OR DATA,THAT MAY ARISE FROM THEUSE OF THIS DOCUMENT OR THE INFORMATION IN IT.

This documentation and the product it describes are considered protected by copyrights andother intellectual property rights according to the applicable laws.

The wave logo is a trademark of Nokia Siemens Networks Oy. Nokia is a registered trademarkof Nokia Corporation. Siemens is a registered trademark of Siemens AG.

Other product names mentioned in this document may be trademarks of their respectiveowners, and they are mentioned for identification purposes only.

Copyright Nokia Siemens Networks 2013. All rights reserved.

In addition to above, this document is also intended for the use of NokiaSiemens Networks recycling service providers responsible for the end-of-life treatment of the product. The foregoing disclaimer shall also beapplicable and binding on all such recycling service providers.

8/10/2019 04_FPH800_R2-5_EPD

3/22

Contents


Contents

1

Introduction .......................................................................................... 5

2 Product description ............................................................................. 6

3 Company environmental information ................................................. 73.1 Nokia Siemens Networks environmental policy ...................................... 73.2

Life cycle thinking ................................................................................... 7

3.3 Environmental Management System (EMS) ........................................... 83.4

Design for Environment .......................................................................... 8

4 Product environmental information .................................................... 94.1

Product energy consumption .................................................................. 9

4.2

Product CO2 footprint .......................................................................... 10

4.3 Materials .............................................................................................. 114.3.1 Nokia Siemens Networks Substance List ............................................. 114.3.2 Hazardous Substance Table ................................................................ 124.3.3

Product end-of-life ................................................................................ 13

4.3.4 Main material fractions ......................................................................... 134.3.5 Components and substances which may require special

handling in the end-of-life phase .......................................................... 154.4 Product recyclability rate ...................................................................... 174.5

Product delivery packaging .................................................................. 19

5

Environment related markings .......................................................... 20

5.1

EU WEEE marking of separate collection ............................................ 20

5.2 Marking according to the Chinese standard SJ/T 11364-2006 ............. 21

6 Take-back information ....................................................................... 22

8/10/2019 04_FPH800_R2-5_EPD

4/22

8/10/2019 04_FPH800_R2-5_EPD

5/22

Introduction


1 IntroductionThe purpose of this document is to provide environmentally relevantinformation of a specific Nokia Siemens Networks product.

This document shall not be interpreted as a specification, modification oramendment to the specification, or additional or other warranty of anykind. In case of discrepancy between this document and the Productspecification or terms and conditions of the valid supply agreementbetween Nokia Siemens Networks and the customer, the supplyagreement and Product specification shall always prevail over thisdocument.

8/10/2019 04_FPH800_R2-5_EPD

6/22



2 Product descriptionType of the product

Product name FlexiPacket Hub 800 2.5Product configuration -

NSN code / productID

T555800MB.00, T555800GBE.00, T555800E1.16,T555800PWI.00, T555800FB.00, T555800GBO.00

8/10/2019 04_FPH800_R2-5_EPD

7/22

Company environmental information


3 Company environmental information

3.1 Nokia Siemens Networks environmental policyNokia Siemens Networks strives through the creation of innovativeproducts to improve the quality of life the world over and maximize thebenefits of Information and Communication Technology (ICT).

As a global company we are facing special responsibility for worldwidelong-term challenges and take seriously our responsibility forenvironmental protection and resource stewardship.

Sustainability is the key to securing our companys future. Central to thisthinking is meeting the demands of business in an ecologically andsocially progressive manner. A demonstrated commitment to

environmental protection will increase the competitive advantage ofbusinesses and our customers and lay the foundation for a successfulfuture.

Our global system for managing environmental protection ensurescontinuous improvement of our environmental performance. We design,develop, manufacture and market our products and services in a mannerthat meets or exceeds applicable regulations and minimizes the impacton natural resources.

Our management and employees act in accordance with this policy andobserve the relevant regulations. We are taking also extended companyresponsibility and are requiring our contractors to act according to thispolicy.

3.2 Life cycle thinking

The environmental goals and activities of Nokia Siemens Networks areaimed at reducing the environmental impact of Nokia Siemens Networks

8/10/2019 04_FPH800_R2-5_EPD

8/22



products over their entire life cycle. Life-cycle thinking is used throughoutthe products phases from raw material extraction, manufacturingoperations, use phase and end-of-life practices as well as logistics.

Continuous activities on these fields assure to minimize theenvironmental impacts of our products.

3.3 Environmental Management System (EMS)

Nokia Siemens Networks is increasingly concerned with achieving anddemonstrating sound environmental performance by controlling theimpacts of their activities, products and services on the environment.

Therefore ISO 14001 international standard covering environmentalmanagement, provides Nokia Siemens Networks with the elements of aneffective management system. Additionally all manufacturing sites ofNokia Siemens Networks are certified by an external body according toISO 14001.

3.4 Design for Environment

Design for Environment (DfE) means systematic integration of

environmental objectives into product design. In Nokia SiemensNetworks, products are designed to be environmentally efficient byintegrating several tasks to product process performing to

minimize material and energy use

maximize reuse and recycling

minimize use of materials harmful to the environment

design products to be easily or remotely maintainable ormaintenance free.

DfE is an integral part of Product Process in NSN and thus considered inday-to-day decision making in Nokia Siemens Networks.

8/10/2019 04_FPH800_R2-5_EPD

9/22

8/10/2019 04_FPH800_R2-5_EPD

10/22

8/10/2019 04_FPH800_R2-5_EPD

11/22

Product environmental information


Total CO2footprint (kg) = energy consumption (kW) x time of use (h) xemission factor (kg CO2/kWh).

Area Electr ic it y emissionfactor (kg CO2/kWh)*

Total CO2footprint (kg)

World 0.502 1649

EU 0.341 1120

Asia(ex. China) 0.728 2391

China 0.788 2589

USA 0.573 1882

Latin America 0.197 647

*) Emission factors are taken from A WRI/WBCSD GHG Protocol Initiative calculationtool (2007). More information can be found fromwww.ghgprotocol.org.

4.3 Materials

4.3.1 Nokia Siemens Networks Substance List

Nokia Siemens Networks has compiled a Substance List based onregulatory requirements and reasonable facts. The Substance Listidentifies substances in two categories:

Banned or restricted substances category identifies substancesthat are banned or restricted in applications (solders, pastes, etc.),parts, subassemblies and accessories related to Nokia SiemensNetworks products and/or packaging.

Monitored substances category lists substances that NokiaSiemens Networks expects, based on reasonable facts, to bereduced or phased out from Nokia Siemens Networks productsand/or packaging, subject to the availability of technically,environmentally and economically sound alternatives. Suppliersare strongly advised to investigate suitable alternative solutions.
http://www.ghgprotocol.org/http://www.ghgprotocol.org/http://www.ghgprotocol.org/http://www.ghgprotocol.org/

8/10/2019 04_FPH800_R2-5_EPD

12/22



4.3.2 Hazardous Substance Table

The following table shows Material usage information of Networks

Electronic Information Products imported or sold in the PeoplesRepublic of China.

(Hazardous Substance)

(Item)

(Pb)

(Hg)

(Cd)

(Cr6+)

(PBB)

(PBDE)

(Metal Parts)

(Circuit Modules)

(Cables & Cable Assemblies)

(Plastic and Polymeric parts)

,,

:

This table shows where these substances may be found in the supply chain of Nokia Siemens Networks

electronic information products, as of the date of sale of the enclosed product. Note that some of the

component types listed above may or may not be a part of the enclosed product.

SJ/T 11363-2006

Indicates that the concentration of the hazardous substance in all homogeneous materials in the parts is

below the relevant threshold of the SJ/T 11363-2006 standard.

SJ/T 11363-2006

Indicates that the concentration of the hazardous substance of at least one of all homogeneous

materials in the parts is above the relevant threshold of the SJ/T 11363-2006 standard.

X

The reason for marking with X is: There are not alternative technologies or parts available.

8/10/2019 04_FPH800_R2-5_EPD

13/22



4.3.3 Product end-of-life

Nokia Siemens Networks hereby supplies information supporting

environmentally sound, safe and economical End-of-Life (EoL)handling/recycling of the product. All disassembly, treatment, recoveryand other work must be managed and performed with professionaldiligence and skill, according to good operating practices and theapplicable legal safety, health and environmental requirements andstandards, taking into account all relevant health and safety aspects.

4.3.4 Main material fractions

The main fractions of the Product are listed in the table below. This table

is not inclusive and the product may contain other materials, substances,components or parts than those identified in this document.

Base system (T555800MB.00)

Fraction / material Amount(g)

% Of total weight

Stainless steel 65 3.25%

Aluminum alloys 1200.5 60.09%

Polycarbonate materials 2.3 0.12%

Mixed electronics (including PWB and Mcompo components) 682.2 34.14%

Fan and cables 48 2.40%

Total weight 1998 100.00%

4xGE card (T555800GBE.00)


% Of total weight

Steel 10 6.91%

Aluminum alloys 27 17.76%


PP+EPDM materials 0 0.00

Silicone glue& pad 0 0.00

Mixed electronics (including PWB and Mcompo components) 114 75.00%


8/10/2019 04_FPH800_R2-5_EPD

14/22



16xE1 card (T555800E1.16)


% Of total weight

Steel10 6.91%

Aluminum alloys27 17.76%

Polycarbonate materials0.5 0.33%





Power injector card (T555800PWI.00)


% Of total weight

Steel 10.1 4.5%







2xFB card (T555800FB.00)


% Of total weight

Steel 10.1 5.9%


Polycarbonate materials 0.9 0.5





8/10/2019 04_FPH800_R2-5_EPD

15/22



4xGEO card (T555800GBO.00)


% Of total weight

Steel 10.1 6.9%







4.3.5 Components and substances which may require special handlingin the end-of-li fe phase

Based on Nokia Siemens Networks sole consideration, the recyclingservice providers shall at least take into consideration, that such productmay include the following materials, substances, components and partswhich may require special handling at end-of- life. In addition to the listbelow product may contain other materials and substances typicallyused in telecommunication equipment (such as but not limited to lead).The product contains at least the following materials that may requirespecial handling at end-of- life but this list is non-exhaustive:

8/10/2019 04_FPH800_R2-5_EPD

16/22



Material, component, part Yes No Appli cation /

Location

Polychlorinated biphenyls (PCB) containingcapacitors

X

Mercury containing components X

Batteries X

Printed circuit boards (PCB) greater than 10 cm X

Containing toners in the form of liquid(s),powders(s) or paste(s)

X

Plastics containing brominated flame retardants X

Asbestos waste and components which containasbestos X

Cathode ray tubes X

Chlorofluorocarbons (CFC),hydrochlorofluorocarbons (HCFC) orhydrofluorocarbons (HFC), hydrocarbons (HC)

X

Gas discharge lamps X

Liquid crystal displays of a surface greater than 100cm, and all those back-lighted with gas dischargelamps

X

External electric cables X

Components containing refractory ceramic fibres X

Components containing radioactive substances X

Electrolyte capacitors (with a height > 25 mm, adiameter > 25 mm or proportionately similarvolume)

X

Beryllium Oxide

Beryllium compounds X

Pressure X

Liquids X

Gases X

Hidden mechanical springs or other equivalent X

8/10/2019 04_FPH800_R2-5_EPD

17/22



4.4 Product recyclability rate


Unit Data

Weight of materials which are (alsotheoretically) recyclable

g. 1571.9

Total weight of the product g 1998

Recyclability rate Percentage (%) 78,67%

4xGE card (T555800GBE.00)

Unit Data


g. 83.6


Recyclability rate Percentage (%) 55%

16xE1 card (T555800E1.16)

Unit Data


g. 83.6


Recyclability rate Percentage (%) 55%

8/10/2019 04_FPH800_R2-5_EPD

18/22



Power injector card (T555800PWI.00)

Unit Data


g. 111.6


Recyclability rate Percentage (%) 50.3%

2xFB card (T555800FB.00)

Unit Data


g. 91.6


Recyclability rate Percentage (%) 53.3%

4xGEO card (T555800GBO.00)

Unit Data


g. 81.2


Recyclability rate Percentage (%) 55,6%

8/10/2019 04_FPH800_R2-5_EPD

19/22



4.5 Product delivery packaging

The common materials used for the delivery packaging of the NSN products arelisted below.


PackagingType

MaterialAverage Weight

(g)Material recyclabilit y

Unit Package Corrugated board 760 100%

Inner part PE 250 100%

Antistatic bag PE 50 100%

PIUs (T555800E1.16, T555800GBE.00,etc)

PackagingType

MaterialAverage Weight

(g)Material recyclabilit y

Unit Package Corrugated board 100 100%

Inner part PE 50 100%

Antistatic bag PE 30 100%

Packaging materials are marked according to

ISO 11469 standard (Plastics generic identification and marking of plasticproducts)

DIN 6120-1 and DIN 6120-2 standards (Marking of packaging and packagingmaterials for recycling purposes - Plastics packaging and packaging materials)

GB 18455:2001 (Packaging Recycling Marks, National Standard of the PeoplesRepublic of China)

The packaging materials comply with the Essential requirements stated inPackaging and Packaging Waste Directive (94/62/EC).

8/10/2019 04_FPH800_R2-5_EPD

20/22



5 Environment related markings

5.1 EU WEEE marking of separate collection

8/10/2019 04_FPH800_R2-5_EPD

21/22

Environment related markings


5.2 Marking according to the Chinese standard SJ/T11364-2006

SJ/T 11364-2006

,

,.

Marking according to the Chinese standard SJ/T 11364-2006:

The marking for Environmental Friendly Use Period is applicable onlywithin Peoples Republic of China. The Environmental Friendly UsePeriod is valid only if product is used and operated strictly in accordance

with the relevant product manual.

8/10/2019 04_FPH800_R2-5_EPD

22/22



6 Take-back informationNokia Siemens Networks customers can contract with Nokia SiemensNetworks for environmentally responsible end-of-life treatment of

obsolete equipment. The purpose is to recover the material and energycontent of the obsolete products and to ensure safe treatment ofsubstances that can cause harm to people or the environment, ifdisposed of untreated. In a life-cycle perspective, EoL treatment cancompensate for some of the environmental impacts of the earlier stagesof the products life cycle.

Nokia Siemens Networks Equipment Take Back Solution provides NokiaSiemens Networks customers with an end-to-end service that includesthe removal of end-of-life products from the customers' network andensures end-of-life treatment in an environmentally responsible way.The Nokia Siemens Networks Equipment Take Back Solution is offered

in several modules representing end-to-end work flow of the process: Removal

Collection

Recycling

Project Management

In Nokia Siemens Networks or Other Vendor HW Replacement, that is,SWAP cases Take Back Solution brings in Collection and RecyclingService as Removal and Project Management are already included. Thepricing is scalable according to the modules.

If customer chooses not to procure Nokia Siemens Networks EquipmentTake Back Solution from Nokia Siemens Networks, customer agrees todispose of any such equipment in a sound environmental manner, incompliance with all applicable laws.

Date post:	02-Jun-2018
Category:	Documents
Upload:	iqbal-muhammad
View:	218 times
Download:	0 times

04_FPH800_R2-5_EPD

Documents