057-235 DSEWebNet Smart Device soft - Энерган€¦ · DSEWebNet Smart Device Software Manual...

ISSUE: 1

DEEP SEA ELECTRONICS PLC

DSEWebNet Smart Device Software Manual

Document Number: 057-235

Author: Bedig Boghossian


057-235 ISSUE: 1 Page 2 of 46

DEEP SEA ELECTRONICS PLC Highfield House Hunmanby North Yorkshire YO14 0PH ENGLAND Sales Tel: +44 (0) 1723 890099 Sales Fax: +44 (0) 1723 893303 E-mail: [email protected] Website: www.deepseaplc.com

DSEWebNet PC Internet Browser Software Manual © Deep Sea Electronics PLC All rights reserved. No part of this publication may be reproduced in any material form (including photocopying or storing in any medium by electronic means or other) without the written permission of the copyright holder except in accordance with the provisions of the Copyright, Designs and Patents Act 1988. Applications for the copyright holder’s written permission to reproduce any part of this publication must be addressed to Deep Sea Electronics PLC at the address above. The DSE logo is a UK registered trademarks of Deep Sea Electronics PLC. Any reference to trademarked product names used within this publication is owned by their respective companies. Deep Sea Electronics PLC reserves the right to change the contents of this document without prior notice. Amendments List Issue Comments

1 Initial release

Typeface: The typeface used in this document is Arial. Care must be taken not to mistake the upper case letter I with the numeral 1. The numeral 1 has a top serif to avoid this confusion.

Clarification of notation used within this publication.

NOTE: Highlights an essential element of a procedure to ensure correctness.

CAUTION!:

Indicates a procedure or practice, which, if not strictly observed, could result in damage or destruction of equipment.

WARNING!:

Indicates a procedure or practice, which could result in injury to personnel or loss of life if not followed correctly.


Page 3 of 46 057-235 ISSUE: 1

TABLE OF CONTENTS

Section Page

1 INTRODUCTION .................................................................................................. 4

1.1 BIBLIOGRAPHY ....................................................................................................................... 5

1.2 GLOSSARY OF TERMS .......................................................................................................... 5

2 INSTALLATION INSTRUCTIONS ....................................................................... 6

2.1 DSEGATEWAY ........................................................................................................................ 6

2.2 SMART DEVICES COMPATIBILITY ....................................................................................... 6

2.2.1 APPLE DEVICES .............................................................................................................. 6

2.2.2 ANDROID SMART DEVICES ............................................................................................ 6

2.2.3 WINDOWS PHONES AND OTHER DEVICES ................................................................. 6

2.3 PC INTERNET BROWSERS .................................................................................................... 6

2.4 DEVICE COMPATIBILITY ........................................................................................................ 7

3 GETTING STARTED ............................................................................................ 8

3.1 DSEWEBNET LOGIN SCREEN ............................................................................................... 8

3.1.1 REGISTRATION, ACCOUNT TYPES AND USES ............................................................ 8

3.1.1.1 USER ACCOUNT ....................................................................................................... 8

3.1.1.2 ORGANISATION ACCOUNT ..................................................................................... 9

3.1.2 REGISTERING A USER ACCOUNT ............................................................................... 10

3.1.2.1 NEW USER REGISTRATION FORM ...................................................................... 11

3.1.3 REGISTERING AN ORGANISATION ACCOUNT .......................................................... 12

3.1.3.1 NEW ORGANISATION REGISTRATION FORM ..................................................... 13

3.2 LOGGING IN ........................................................................................................................... 15

3.2.1 MAXIMUM FAILED LOGIN ATTEMPTS EXCEEDED .................................................... 17

3.2.2 FIREWALL SETTINGS .................................................................................................... 17

3.3 CONFIGURING THE SYSTEM .............................................................................................. 18

3.3.1 ADDING A SITE (DSEGATEWAY).................................................................................. 18

3.3.2 ADDING DSE CONTROLLER OF A SITE ...................................................................... 21

4 OPERATING DSEWEBNET .............................................................................. 22

4.1 SYSTEM OVERVIEW ............................................................................................................. 22

4.1.1 SITE CONNECTION STATUS ICON .............................................................................. 23

4.1.2 SITE ALARM STATUS .................................................................................................... 23

4.1.3 DSE CONTROLLER STATUS ......................................................................................... 24

4.1.4 DSE CONTROLLER ........................................................................................................ 24

4.2 CONFIGURATION MODE ...................................................................................................... 25

4.3 SYSTEM NAVIGATION .......................................................................................................... 26

4.3.1 DSE CONTROLLER IN THE DSEWEBNET APPLICATION .......................................... 26

4.3.2 INFO PAGE ..................................................................................................................... 27

4.3.3 CONTROLS ..................................................................................................................... 28

4.3.4 CONTROL BUTTONS ..................................................................................................... 29

4.3.4.1 AUTOSTART CONTROLLER .................................................................................. 29

4.3.4.2 AMF CONTROLLER ................................................................................................ 30

4.3.4.3 MAINS CONTROLLER ............................................................................................. 31

4.3.4.4 GENERATOR BUS-TIE CONTROLLER .................................................................. 32

4.3.4.5 DSE333 .................................................................................................................... 33

4.3.4.6 DSE334 & DSE335 .................................................................................................. 34

4.3.5 GENERATOR INSTRUMENTS ....................................................................................... 35

4.3.6 MAINS INSTRUMENTS .................................................................................................. 36

4.3.7 ENGINE INSTRUMENTS ................................................................................................ 37

4.3.8 IO ..................................................................................................................................... 38

4.3.9 ALARMS .......................................................................................................................... 39

4.3.10 EVENTS ........................................................................................................................... 40

4.3.11 VIEWING HISTORIC DATA GRAPH............................................................................... 41

4.3.12 OPTIONS ......................................................................................................................... 44

Introduction

057-235 ISSUE: 1 Page 4 of 46

1 INTRODUCTION This manual covers the registration and operation of the DSEWebNet Software for DSE modules using the DSEWebNet Mobile Application on Smart Devices (tablets, smart devices). The DSEWebNet Application is supported on the iOS and Android devices, Windows phones do not support the DSEWebNet Application but DSEWebNet is accessible on the Windows mobile browser. This is not a controlled document. There are no automatic notifications of changes to this manual. Any future updates of this document are included on the DSE website: www.deepseaplc.com The DSEWebNet Mobile Application does not contain all the DSEWebNet functions, the DSEWebNet PC browser must be used instead for the full DSEWebNet functions and features. Refer to the DSE publication: 057-168: DSEWebNet PC Internet Browser Software Manual which is found on the DSE website: www.deepseaplc.com Separate manuals cover the DSE modules supported by the software which is downloaded from our website: www.deepseaplc.com The DSEWebNet App Software in conjunction with the DSE890 & DSE891 Gateway Device allows the user to remote monitor and control a wide range of modules via the DSEWebNet app on the smart device downloadable free of charge from the mobiles application store. The DSEWebNet Software must only be used by competent, qualified personnel, as operating the system may have safety implications on the panel / generating set to which it is fitted. The information contained in this manual must be read in conjunction with the information contained in the appropriate module documentation. A separate manual deals with the operation of the DSEGateway (See section entitled Bibliography elsewhere in this document).

Introduction

Page 5 of 46 057-235 ISSUE: 1

1.1 BIBLIOGRAPHY This document refers to and is referred to by the following DSE publications that is obtained from the DSE website www.deepseaplc.com DSE Part No Description

053-140 DSE890 & DSE891 Installation Instructions

057-165 DSE890 & DSE891 Operators Manual

057-168 DSEWebNet PC Internet Browser Software Manual

057-156 DSE334 Configuration Suite PC Software Manual


057-187 DSEL400 & DSEL401 Configuration Suite PC Software Manual

057-222 DSEL401 MKII Configuration Suite PC Software Manual

057-178 DSE4310 & DSE4320 Configuration Suite PC Software Manual





057-223 DSE6010 MKII & DSE6020 MKII Configuration Suite PC Software Manual





057-077 DSE72xx & DSE73xx Configuration Suite PC Software Manual



057-119 DSE8610, DSE8620 & DSE8660 Configuration Suite PC Software Manual

057-238 DSE8610MKII Configuration Suite PC Software Manual

057-257 DSE8660MKII Configuration Suite PC Software Manual




057-251 DSEE400 Configuration Suite PC Software Manual

057-203 DSEE800 Configuration Suite PC Software Manual

1.2 GLOSSARY OF TERMS Reference Description

DSEGateway Refers to the DSE890 and DSE891 DSEGateway devices.

Site Refers to the DSE890 and DSE891 DSEGateway devices.

DSE Controller Refers to the DSE Controller connected to the DSE890 or DSE891 DSEGateway devices.

Smart Device Refers to cellphones, tablets, and smart phones.

Installation Instructions

057-235 ISSUE: 1 Page 6 of 46

2 INSTALLATION INSTRUCTIONS

2.1 DSEGATEWAY For information with regards to setting up the DSE890 or DSE891 Gateway Device, refer to DSE Publication: 057-165 DSE890 & DSE891 Gateway Operators Manual which is found on the DSE website: www.deepseaplc.com

2.2 SMART DEVICES COMPATIBILITY

2.2.1 APPLE DEVICES DSEWebNet application is optimised for iOS 8.1 or later. Compatible with iPhone, iPad, and iPod touch.

2.2.2 ANDROID SMART DEVICES DSEWebNet application is optimised for Android 4.0 and above.

2.2.3 WINDOWS PHONES AND OTHER DEVICES Windows phones and other devices do not support DSEWebNet application, but DSEWebNet is accessed through the Windows mobile browsers www.dsewebnet.com in the Windows phones.

2.3 PC INTERNET BROWSERS For information with regards to using the DSEWebNet on a PC, refer to DSE Publication: 057-168 DSEWebNet PC Internet Browser Software Manual which is found on the DSE website: www.deepseaplc.com

Installation Instructions

Page 7 of 46 057-235 ISSUE: 1

2.4 DEVICE COMPATIBILITY At the time of printing, the following devices are currently compatible with the DSE890 & DSE891. Other devices are being added as part of our ongoing development.

NOTE: Not all variants are available in all markets.

NOTE: Not all instrumentation is available with all controllers. Refer to the Configuration Suite PC Software manual relevant to your controller for details of supported instrumentation.

DSE Controller

DSE334

DSE335

DSEL400

DSEL401, DSEL401 MKII

DSE4310, DSE4310 NC

DSE4320, DSE4320 NC

DSE4410 CAN, DSE4410 MPU

DSE4420 CAN, DSE4420 MPU

DSE4510, DSE4510 NC, DSE4510 RT, DSE4510 RTH

DSE4520, DSE4520 NC, DSE4520 RT, DSE4520 RTH, DSE4520 A1

DSE4610, DSE4610 RTH DSE4620, DSE4620 RTH

DSE6010 CAN, DSE6010 MPU, DSE6010 MKII



DSE6120 CAN, DSE6120 MPU, DSE6120 A3, DSE6120 MKII

DSE7110, DSE7110 MKII


DSE7210

DSE7220



DSE7410

DSE7420

DSE7450

DSE8610, DSE8610MKII

DSE8620

DSE8660, DSE8660MKII

DSE8710

DSE8760

DSE8810

DSE8860

DSEE400

DSEE800

Getting Started

057-235 ISSUE: 1 Page 8 of 46

3 GETTING STARTED Launch the DSEWebNet app on the smart device.

3.1 DSEWEBNET LOGIN SCREEN

3.1.1 REGISTRATION, ACCOUNT TYPES AND USES 3.1.1.1 USER ACCOUNT A User Account is a quick and simple way for a single user to start and take control of DSE devices remotely. A User Account is best suited to those who:

• Only have a small number of DSE devices to monitor

• Do not require all the additional features of the Organisation Account

• Needs to be registered under an Organisation Account to restrict their access.

Click to register a new user account on the DSEWebNet. Refer to the next section for the details.

Enter the DSEWebNet account’s username

Enter the DSEWebNet account’s password

Click to enter to the DSEWebNet account after providing the correct Username and Password

Click to retrieve a forgotten or lost password

Getting Started

Page 9 of 46 057-235 ISSUE: 1

3.1.1.2 ORGANISATION ACCOUNT

NOTE: Configuration in the DSEWebNet and access to the Organisation account’s Admin configuration is only accessible through the PC browser. It is not possible to access the Webnet Configuration through the DSEWebNet application on smart devices. For further information you must refer to DSE Publication: 057-168 DSEWebNet PC Internet Browser Software Manual located on the DSE website: www.deepseaplc.com

An Organisation Account is a simple way for an organisation or company manager to start and take control of DSE devices. An Organisation Account is best suited to an organisation or company who:

• Have a single user who wants to gain additional features.

• Have a number of DSE devices to monitor.

• Want to create access permissions to limit access for certain User Accounts registered to the organisation.

In addition to access permissions, an Organisation Account has the ability to setup and configure the following features:

• Geofencing

• Geotracking

• Customisable graphical user interface

• Configurable module and site names

Getting Started

057-235 ISSUE: 1 Page 10 of 46

3.1.2 REGISTERING A USER ACCOUNT To register a new user account, click on New User? then click on Register in the Register User section located on the right hand side of the application, the registration form then appears.

Click to register a new user account for the DSEWebNet


Getting Started

Page 11 of 46 057-235 ISSUE: 1

3.1.2.1 NEW USER REGISTRATION FORM

NOTE: If the confirmation email for the DSEWebNet registration is not recieved, check the email’s junk or spam email folder.

Once the registration form has been completed, click the Register button to complete. An email is sent to the new user’s email address to confirm the registration. To cancel the registration, click the Cancel button.

Blank registration form Example of a completed registration form

Field Description

First Name Enter the new user’s first name

Last Name Enter the new user’s last name

Email

NOTE: A registration confirmation email is sent to the email address entered, ensure the email address is valid.

Enter the new user’s email address. This is the default address allocated to Event Triggers and Reports when configured through the PC web browser.

Confirm Email Re-enter the new user’s email address for confirmation

Phone Number Enter the new user’s mobile phone number with the country code. This is the default number allocated to Event Triggers when configured through the PC web browser.

Username Enter the desired username for the new user’s account.

Password

NOTE: This field is CASE SENSITIVE

Enter the desired password for the new user’s account.

Confirm Password


Re-enter the desired password for confirmation

Captchure


Enter the text displayed in the image below.

Click button to change the image if the text is not clear.

Click button to enunciate the text in the image if it is not clear.

Getting Started

057-235 ISSUE: 1 Page 12 of 46

3.1.3 REGISTERING AN ORGANISATION ACCOUNT To register an organisation account, click on New User? then click on Register in the Register Organisation section located on the right hand side of the application, the registration form then appears.

Click to register a new Organisation Account for the DSEWebNet


Getting Started

Page 13 of 46 057-235 ISSUE: 1

3.1.3.1 NEW ORGANISATION REGISTRATION FORM

NOTE: If the confirmation email for the DSEWebNet registration is not recieved, check the email’s junk or spam email folder.

Once the registration form has been completed, click the Register button to complete. An email is sent to the organisation administrator’s email address to confirm the registration. To cancel the registration, click the Cancel button.

Blank registration form Example of a completed registration form

Field Description

First Name Enter the organisation administrator’s first name

Last Name Enter the organisation administrator’s last name

Email

NOTE: A registration confirmation email is sent to the email address entered, ensure the email address is valid.

Enter the organisation administrator’s email address. This is the default address allocated to Events Triggers and reports when configured using the PC web browser.

Phone Number Enter the organisation administrator’s mobile phone number with the country code. This is the default number allocated to Event Triggers when configured using the PC web browser.

Admin Username Enter the desired username for the organisation account.

Admin Password


Enter the desired password for the organisation account.

Getting Started

057-235 ISSUE: 1 Page 14 of 46

Field Description

Organisation


NOTE: This name is used when a User Account requests to join the Organisation Account.

Enter the name of the organisation or company the account is for.

Building Name/Number Enter the building name or number of the organisation or company.

Street Enter the street the organisation or company is located on.

Town Enter the town the organisation or company is located in.

City Enter the city the organisation or company is located in.

Post/Zip Code Enter the post or zip code of the organisation or company.

Country Select the country the organisation or company is located in.

Captchure


Enter the text displayed in the image below.

Click button to change the image if the text is not clear.

Click button to enunciate the text in the image if it is not clear.

3.2 LOGGING IN

NOTE: To log in to the DSEWebNetrefer to the section ‘Registering an Account’

Launch the DSEWebNet application

The login page may appear in two forms, when the DSEWebNet application is first launched the following page appears. To login, type the registered account details and the password in the ‘Password

After returning from the registration page back to the login, the following page appears.

Getting Started

Page 15 of 46

DSEWebNet, a user account is required. To register anRegistering an Account’ elsewhere in this document.

the DSEWebNet application to access the DSEWebNet Software.

The login page may appear in two forms, when the DSEWebNet application is first launched the login, type the registered account details in the ‘Username or USBID’

Password’ field.

returning from the registration page back to the login, the following page appears.

Enter user account details to login.

057-235 ISSUE: 1

. To register an account,

The login page may appear in two forms, when the DSEWebNet application is first launched the Username or USBID’ field

returning from the registration page back to the login, the following page appears.

Enter user account details to login.

Getting Started

057-235 ISSUE: 1 Page 16 of 46

Field Description

Username Enter the username of the registered account

Password


Enter the password of the registered account

Remember login details

NOTE: Enabling this option requires the use of cookies, contact the IT department if in doubt.

��= The user has to manually enter the account details every time. ��= The user’s account details are remembered by the app when launched. Forget: Click to forget the remembered username and password.

Reset Password

NOTE: If the password retrieval email is not received, check the email’s junk or spam email folder.

To retrieve a forgotten or lost password, click the ‘Forgotten password?’ link. Enter the username of the account and click continue. A new password is sent to the registered email address for that account.

Getting Started

Page 17 of 46 057-235 ISSUE: 1

3.2.1 MAXIMUM FAILED LOGIN ATTEMPTS EXCEEDED If the user’s password is entered incorrectly three times, the account is locked and the password must be reset. To reset the user’s password, click on the ‘Forgotten Password ?’ option in the Login page. This sends a new password to the registered email address for that account. If the reset password email is not received, check the email’s junk or spam email folder.

3.2.2 FIREWALL SETTINGS To provide the best possible service, it is recommended that any firewall is configured to allow access to all subdomains on the dsewebnet.com and deepseaplc.com domain as follows: Domain

*.dsewebnet.com

*.deepseaplc.com

Maximum Failed Login Attempts Exceeded warning

Reset Password option

Getting Started

057-235 ISSUE: 1 Page 18 of 46

3.3 CONFIGURING THE SYSTEM

3.3.1 ADDING A SITE (DSEGATEWAY)

NOTE: To add a DSEGateway to the DSEWebNet, the DSEGateway MUST have been connected to the configured DSE Controllers and to the internet by an Ethernet or GPRS/GSM connection at least once.

Upon first login, the user is presented with a ‘blank’ account with no DSEGateway Devices configured. To add or remove a DSEGateway to the account, click on ‘Add’ located on the left/bottom side of the app page. A pop-up box then appears.

Click to Add Site to the DSEWebNet®

Getting Started

Page 19 of 46 057-235 ISSUE: 1

NOTE: For information with regards to the set up of the DSEGateway, refer to DSE Publication: 057-165 DSE890 & DSE891 Gateway Operators Manual located on the DSE website: www.deepseaplc.com

To add or remove a DSEGateway to the user’s account, the Gateway Device ID and Security Code are required. This information is located in the DSEGateway configuration screens.

The Gateway Device ID is located under the Status | Info section of the DSEGateway® configuration.

The Security Code is located under the Gateway Setup section of the DSEGateway® configuration.

Click to Add DSEGateway

Click to Exit without saving

Getting Started

057-235 ISSUE: 1 Page 20 of 46

If the DSEGateway being added to the user account is not connected to the internet, the below error message appears. Check to ensure that the DSEGateway is connected to the internet and the ID provided is correct.

Getting Started

Page 21 of 46 057-235 ISSUE: 1

3.3.2 ADDING DSE CONTROLLER OF A SITE

NOTE: It is not possible to Remove sets through the DSEWebNet Smart Device Application. Remove sets from the DSEWebNet is achieved using the DSEWebNet over the PC Browser. For more details on adding and removing sets, refer to DSE publication: 057-168 DSEWebNet PC Internet Browser Software Manual located on our website: www.deepseaplc.com

All the DSE controllers connected to the DSEGateway are added to the account once the Add is pressed. The following message appears when the sets are added, press OK to view the sets.

Operating DSEWebNet

057-235 ISSUE: 1 Page 22 of 46

4 OPERATING DSEWEBNET

4.1 SYSTEM OVERVIEW The image below shows an example of a DSEWebNet system monitoring two different sites with multiple generators connected to each site. See subsequent sections for more details on the features highlighted below.

NOTE: Depending which System View Level the user has selected, certain areas of the app page layout change.

System View Level

System Navigation or DSE Controller Information Section (Changes at different system view levels)

The number here refers to the unchecked number of events in the DSE Controller. Once the DSE Controller is accessed, this number returns to zero.

Click to Add a new Site. Refer to section entitled Adding A Site elsewhere in this document for more details.

Click to go to the Options of the DSEWebNet app. Refer to section entitled Options elsewhere in this document.

Click to log out from the DSEWebNet account.

Click (-) to minimize the Site to hide the DSE controllers connected

Click (+) to expand the site to view the DSE controllers connected

Click on the DSE Controller or Site to view that System Level

DSE Controller’s unique USB ID

The DSEGateway derives the Site Name from the configuration, as shown below.

Site Connection Status Icon, see table below

When site is expanded, the DSE Controller Status is indicated by colour and text. The colour of the DSE Controller changes depending on the severity of the fault and it flashes in case of any fault.

Operating DSEWebNet

Page 23 of 46 057-235 ISSUE: 1

4.1.1 SITE CONNECTION STATUS ICON The table below shows the icons used to represent the different site connection statuses on the DSEWebNet.

Icon Description

The DSEGateway is offline (no communication)

The DSEGateway is online and communicating via an Ethernet connection

The DSEGateway is online and communicating via a GSM connection

4.1.2 SITE ALARM STATUS The table below shows the colours used to represent the different alarm statuses of a Site on the DSEWebNet.

State Description

No active alarms on the site.

At least one DSE Controller on the Site has a Warning alarm active.

At least one DSE Controller on the Site has an Electrical Trip alarm active.

At least one DSE Controller on the Site has a Shutdown alarm active.

Operating DSEWebNet

057-235 ISSUE: 1 Page 24 of 46

4.1.3 DSE CONTROLLER STATUS The table below shows the colours used to represent the status of a DSE Controller on the DSEWebNet.

State Description

The DSE Controller is offline (no communication)

The DSE Controller is online (communicating) and in standby in any control mode

The DSE Controller is running a generator in any control mode.

The DSE Controller has a Warning alarm active

The DSE Controller has an Electrical Trip alarm active

The DSE Controller has a Shutdown alarm active.

4.1.4 DSE CONTROLLER

NOTE: Alarms, events, control features and parameters that are monitored are dependent upon the DSE Controller’s specification. Refer to the DSE Controller’s Operators and Software Manuals for further details.

Information displayed under the DSE Controller section is only for that one controller that is configured to the user’s account.

Operating DSEWebNet

Page 25 of 46 057-235 ISSUE: 1

4.2 CONFIGURATION MODE

NOTE: The Configuration is only accessible through the PC browser, refer to DSE publication: 057-168 DSEWebNet PC Internet Browser Software Manual located on our website: www.deepseaplc.com

The DSEWebNet comprises Reports, Event Triggers, Admin section for the Organisation accounts. At the time of writing, the configuration of these features is not available in the DSEWebNet Smart Device application.

Operating DSEWebNet

057-235 ISSUE: 1 Page 26 of 46

4.3 SYSTEM NAVIGATION

NOTE: For information with regards to the set up of the DSEGateway, refer to DSE Publication: 057-165 DSE890 & DSE891 Gateway Operators Manual located on our website: www.deepseaplc.com

4.3.1 DSE CONTROLLER IN THE DSEWEBNET APPLICATION Click on the relevant DSE Controller to access to its instrument sections page. Depending from the DSE Controller’s model, different Instruments sections are available. For instance, a Remote Start Module does not have a Mains section. The example below shows the sections page of an AMF controller, click on the desired section to access to the different instruments of the DSE Controller.

Click on the desired section to enter to the relevant instruments page

Site name and DSE Controller’s name or USBID

Click on Back to go back to the Sites

Click on Options to go to the Options page

Operating DSEWebNet

Page 27 of 46 057-235 ISSUE: 1

4.3.2 INFO PAGE This page details the DSE Controller’s information and status.

Controller status and operating information

Operating DSEWebNet

057-235 ISSUE: 1 Page 28 of 46

4.3.3 CONTROLS

NOTE: The displayed instruments change depending upon the controller type being viewed.

This page contains the control buttons of the relevant DSE Controller. Control buttons differ according to the DSE Controller’s model.

Refer to section Control Buttons elsewhere in this document for more details.

4.3.4 CONTROL BUTTONS

NOTE: Control buttons and operating proceduresController’s specification. Refer to the further details.

NOTE: Dependent upon accesschanges to the graphical user interface using the disabled using the PC Browser only.

The Control Buttons provide the user with the ability to control a 4.3.4.1 AUTOSTART CONTROLLER

Button Mode

Stop

Manual

Automatic

Mute

Start

Unload Generator

Load Generator

On

Off

Operating DSEWebNet

Page 29 of 46

CONTROL BUTTONS

NOTE: Control buttons and operating procedures are dependent upon the efer to the DSE Controller’s Operators and Software Manuals for

nt upon access restrictions set by the Organisation Administrator changes to the graphical user interface using the Widget Editor, the control buttons disabled using the PC Browser only.

provide the user with the ability to control a DSE Controller remotely with ease.

AUTOSTART CONTROLLER

Description

Places the DSE Controller into Stop Mode. Click the button to reset any latching alarms. It immediately opens the generator load switch and stops the engine.

Places the DSE Controller into Manual Mode. Clickenable the user to start the engine by the Startthe generator load switch using the Unload GeneratorGenerator buttons.

Places the DSE Controller into Automatic Modeto enable the DSE Controller to start and stop the engine automatically by different methods.

Click the button to mute the alarm sounder on the and also perform a lamp test.

When in Manual Mode, click the button to start

When in Manual Mode, click the button to openswitch.

Load Generator When in Manual Mode, click the button to closeload switch.

The LED indication on the DSE Controller is active. This shows the status of operating mode and load switch status.

The LED indication on the DSE Controller is not active. This shows the status of operating mode and load switch status.

057-235 ISSUE: 1

are dependent upon the DSE Operators and Software Manuals for

Organisation Administrator or the control buttons are

remotely with ease.

Click the button to immediately opens the generator load

. Click the button to Start button and control

Unload Generator and Load

Automatic Mode. Click the button enable the DSE Controller to start and stop the engine

the alarm sounder on the DSE Controller

to start the generator.

to open the generator load

to close the generator

on the DSE Controller is active. This shows the status of operating mode and load switch status.


057-235 ISSUE: 1

4.3.4.2 AMF CONTROLLER

Button Mode

Stop

Manual

Test

Automatic

Mute

Start

Transfer to Mains

Transfer to Generator

On

Off

Operating DSEWebNet

Page 30 of 46

Description

Places the DSE Controller into Stop Mode. Click the button to reset any latching alarms. It immediately opens the generator load switch and stops the engine.

Places the DSE Controller into Manual Mode. Click theenable the user to start the generator by the Startcontrol the generator and mains load switch using the Mains and Transfer to Generator buttons.

Places the DSE Controller into Test Mode. Click theenable the user to start the generators to give a test on load or island mode facility depending on module configuration.

Places the DSE Controller into Automatic ModeDSE Controller to start and stop automatically by different methods.

Click the button to mute the alarm sounder on the and to perform a lamp test.

When in Manual Mode, click the button to start the generator.

When in Manual Mode, click the button to transfer the load from the generator to the Mains.

When in Manual Mode, click the button to transferthe Mains to the generator.



. Click the button to reset any latching alarms. It immediately opens the generator load

. Click the button to Start button and

control the generator and mains load switch using the Transfer to

. Click the button to to start the generators to give a test on load or

island mode facility depending on module configuration.

Automatic Mode. This enables the DSE Controller to start and stop automatically by different


start the generator.

transfer the load from

to transfer the load from

The LED indication on the DSE Controller is active. This shows switch status.


4.3.4.3 MAINS CONTROLLER

Button Mode

Stop

Manual

Test

Automatic

Mute

Start

Transfer to Mains

Transfer to Generator Bus

On

Off

Operating DSEWebNet

Page 31 of 46

MAINS CONTROLLER

Description

Places the DSE Controller into Stop Mode. Click thereset any latching alarms. It immediately opens the generator bus load switch and removes the start request.

Places the DSE Controller into Manual Mode. Click theenable the user to start the generator by the Startcontrol the generator bus and mains load switch using the Transfer to Mains and Transfer to Generator Bus

Places the DSE Controller into Test Mode. Click theenable the user to start the generator by the Starttest on load or island mode facility depending on module configuration.

Places the DSE Controller into Automatic Modeto enable the DSE Controller to start and stop the generators automatically by different methods.

Click the button to mute the alarm sounder on the DSE Controller and to perform a lamp test.

When in Manual Mode, click the button to start the generators.

When in Manual Mode, click the button to transferthe generator bus to the Mains.

When in Manual Mode, click the button to transferthe Mains to the generator bus.



057-235 ISSUE: 1

. Click the button to immediately opens the generator bus

. Click the button to Start button and

control the generator bus and mains load switch using the Bus buttons.

. Click the button to Start button to give a

test on load or island mode facility depending on module

Automatic Mode. Click the button the DSE Controller to start and stop the generators


start the generators.



The LED indication on the DSE Controller is active. This shows operating mode and load switch status.


057-235 ISSUE: 1

4.3.4.4 GENERATOR BUS-TIE CONTROLLER

Button Mode

Alarm Reset

Manual

Automatic

Mute

Generator Bus-Tie Load Switch Control

On

Off

Operating DSEWebNet

Page 32 of 46

TIE CONTROLLER

Description

Click the button to reset any latching alarm.

Places the DSE Controller into Manual Mode. Click theenable the user to control the generator bus-tie load switch using the Generator Bus-Tie Load Switch Control button.

Places the DSE Controller into Automatic Modeto enable the DSE Controller to open and close the generator bus-tie load switch automatically by different methods.

Click the button to mute the alarm sounder on the and to perform a lamp test.

When in Manual Mode, click the button to closegenerator bus-tie load switch.



. Click the button to tie load switch using

button.

Automatic Mode. Click the button the DSE Controller to open and close the generator

tie load switch automatically by different methods.


to close or open the

The LED indication on the DSE Controller is active. This shows and load switch status.


4.3.4.5 DSE333

Button Mode

Auto

Prohibit Return

Test On Load

Manual

Transfer to Mains

Transfer to Generator

On

Off

Operating DSEWebNet

Page 33 of 46

Description

Places the DSE Controller into Automatic Modeto enable the DSE Controller to start and stop the generator automatically by different methods.

Places the DSE Controller into Prohibit Return Modebutton to enable the DSE Controller to start and stop automatically by different methods. Additionally itgenerator returning the load to the Mains until instructed.

Places the DSE Controller into Test Mode. This enables the user to start the generator to give a test facility.

Places the DSE Controller into Manual Mode. Click thestart the generator and enable the user to control the generator and mains load switch using the Transfer to Mainsto Generator buttons.

When in Manual Mode, click the button to transferthe generator to the Mains.

When in Manual Mode, click the button to transferthe Mains to the generator.



057-235 ISSUE: 1

Automatic Mode. Click the button the DSE Controller to start and stop the generator

Prohibit Return Mode. Click the the DSE Controller to start and stop

automatically by different methods. Additionally it prevents the generator returning the load to the Mains until instructed.

. This enables the user

. Click the button to the user to control the generator

Mains and Transfer



indication on the DSE Controller is active. This shows the status of operating mode and load switch status.


057-235 ISSUE: 1

4.3.4.6 DSE334 & DSE335

Button Mode

Stop

Manual

Mode

Automatic

Mute

Tick

Transfer to S1

Transfer to S2

On

Off

Operating DSEWebNet

Page 34 of 46

Description

Places the DSE Controller into Stop Mode. Click thereset any latching alarms. It immediately opens S2 load switch and removes the start request.

Places the DSE Controller into Manual Mode. Click thestart the generator and enable the user to control S1 and S2 load switches using the Transfer to S1 and Transfer to S2

Click the button to cycle through other available operating modes (Test On Load, Test Off Load & Prohibit Return). Click the button to select once desired operating mode has appeared.

Places the DSE Controller into automatic mode. Click theto enable the module to start and stop automatically via different methods.

Click the button to mute the alarm sounder on the DSE Controller and to perform a lamp test.

When the DSE Controller is cycling through different operating modes using the Mode button, click the buttonmode selected.

When in Manual Mode, click the button to transferS2 to S1.

When in Manual Mode, click the button to transferS1 to S2.



. Click the button to immediately opens S2 load switch

. Click the button to the user to control S1 and S2 load

Transfer to S2 buttons.

through other available operating modes Prohibit Return). Click the Tick

button to select once desired operating mode has appeared.

de. Click the button the module to start and stop automatically via different


the DSE Controller is cycling through different operating button to enter to the



The LED indication on the DSE Controller is active. This shows operating mode and load switch status.


Operating DSEWebNet

Page 35 of 46 057-235 ISSUE: 1

4.3.5 GENERATOR INSTRUMENTS

NOTE: To view the Historic Data Graph of an instrument, refer to the section entitled Viewing Historic Data Graph elsewhere in tis document.

This page shows the generator instruments of the DSE Controller selected.

DSE Controller’s measurements of the generator instruments

Click on any instrument to view its Historic Data graph.

Operating DSEWebNet

057-235 ISSUE: 1 Page 36 of 46

4.3.6 MAINS INSTRUMENTS

NOTE: The Mains/S1 section is only available for modules with mains/S1 sensing.

This page shows the mains instruments of the module selected.

Operating DSEWebNet

Page 37 of 46 057-235 ISSUE: 1

4.3.7 ENGINE INSTRUMENTS This page shows the engine instruments of the module selected.

Click on any instrument to view its Historic Data graph.

DSE Controller’s measurements of the engine parameters

Operating DSEWebNet

057-235 ISSUE: 1 Page 38 of 46

4.3.8 IO Displays the configuration and state of the inputs and outputs for the DSE Controller. This section provides diagnostics assistance for fault finding.

Scroll down to view the rest of the page.

The Emergency Stop icon changes when activated

Not Active

Active

Shows if the input or output channel is active or not. This input is opened and is inactive. The input is configured to be close to activate

What the input or output is configured for.

Shows if the input or output channel is active or not. This output is closed and is active. The output is configured to Energise.

Operating DSEWebNet

Page 39 of 46 057-235 ISSUE: 1

4.3.9 ALARMS Displays what alarms are currently active on the DSE Controller. This section provides diagnostics assistance for fault finding.

Alarms displayed are currently active on the DSE Controller.

Operating DSEWebNet

057-235 ISSUE: 1 Page 40 of 46

4.3.10 EVENTS This page shows the Event Logs on the DSE Controller selected.

Events recorded in the DSE Controller’s event log

Operating DSEWebNet

Page 41 of 46 057-235 ISSUE: 1

4.3.11 VIEWING HISTORIC DATA GRAPH

NOTE: To use the Historic Data Graph feature, the DSEGateway device must be configured to upload historic data at a suitable interval as shown below. Refer to DSE Publication: 057-165 DSE890 & DSE891 Operators Manual for further details.

The resolution of the data used in the Graphs is configured in the DSEGateway.

Historic Data Graphs are available for all instruments for a DSE Controller.

Operating DSEWebNet

057-235 ISSUE: 1 Page 42 of 46

Click on the relevant instrument to view the Historic Data graph.

Frequency instrument’s Historic Data graph for the last 10 minutes.

Click here to change the Data Period.

To view Historic Data Graphs, click on the instrument

Operating DSEWebNet

Page 43 of 46 057-235 ISSUE: 1

Edit the Data Period to show the required range of the relevant instrument.

Click on the Data Period tab to open the period selection.

Select Time Interval as the past 10 Minutes, Hour, Day or Week. Then press OK

Operating DSEWebNet

057-235 ISSUE: 1 Page 44 of 46

4.3.12 OPTIONS

Option Description

Animations

On: Animations option is On, in case of an alarm on a site view, the sites and the DSE Controller show the relevant alarm colour by flashing. Off: Animation is Off, no flash in case of an alarm.

Sounds

On: The sounds option is On, in case of any alarm, a sound is generated when the DSEWebNet application is running on the smart device. Off: The sound option is Off.

Local Cache

On: The DSEWebNet application uses the smart devices memory for data cache, this is useful to reduce internet data consumption. Off: The DSEWebNet application downloads the required information each time a page is opened.

Notifications

On: Notifications are On, when viewing the sites page and a new event happens, increments the number next to the DSE Controller. This number returns to zero when viewing the relevant Events. Off: Notifications are Off.

Save Click to save the edited options.

Default Clicking on Default returns the default settings for all options and exits from Options.

Cancel Click to exit Options without saving.

DSEWebNet application’s version.

Shows the option is On.

The option is switched Off.

Click to save the edited options.

Click to return to the Default Options.

Click to exit without saving.

This Page Intentionally Left Blank

This Page Intentionally Left Blank

Date post:	15-Apr-2018
Category:	Documents
Upload:	duongthien
View:	227 times
Download:	5 times

057-235 DSEWebNet Smart Device soft - Энерган€¦ · DSEWebNet Smart Device Software Manual...

Documents