-
Junk Catchers Reverse Circulating Junk Basket
www.gotco-usa.com22
Construction
The tool consists of a top sub,barrel assembly, catcher,
andshoe. The barrel assembly con-
sists of an inner and outer barrel,valve seat, cup, and ball. A
lift subis also provided to assist in han-dling.
Assembly and Operation
Make up the junk basket tothe bottom of the string and runinto
the hole. When the tool isapproximately 10 feet from thebottom of
the hole, the ball isdropped down the drill pipe. Theball will
position itself in the ballseat and reverse circulation willbegin.
Circulate and begin coring.Combined with the reverse circu-lation,
this guarantees that any
Reverse CirculatingJunk BasketThe Gotco Reverse Circulating Junk
Basket (RCB) is a junkretrieval tool designed to remove all types
of objects from thebottom of the well bore. This superior tool
removes such itemsas slips, hand tools, bit cones, and any other
small pieces ofjunk from the well. The RCB uses reverse circulation
to aidjunk recovery.
How to Order Gotco Reverse Circulating Junk BasketsWhen
ordering, please specify:
Name and part number of assembly Connection, if nonstandard O.D.
and type of shoe
Recommended Spares 2 Junk Catchers 1 Valve Seat 2 Mill Shoes 1
Steel Ball 1 Valve Cup
junk on the bottom is pumped intothe barrel and caught by the
catch-er assembly. The tool is removedfrom the hole after cutting
10 to20 inches of core.
Optional Componentsand Accessories
Shoes - Four types of shoesare available to fit the
ReverseCirculating Junk Basket.
Type A mill shoe is suppliedas standard equipment with
thecutting teeth dressed with hardmetal and has side wings. Thetype
A mill shoe is used where theformation is relatively soft andthe
fish is a loose piece.
Type B mill shoe is equal indesign to the type A shoe, howev-er,
it is hard faced with Gotcoloya sintered tungsten carbide in
anextremely tough matrix whichwill effectively and rapidly millup
junk during the fishing opera-tion. This shoe will cut on O.D.,I.D.
and bottom.
Type C mill shoe is also hardfaced with Gotcoloy, however,
isdesigned with a flat bottom, and
the Gotcoloy is placed on theinner face and the outer face.
Thisdesign is used to mill up junk andis extremely effective for
cuttingcores.
Type B or type C Gotcoloydressed milling shoes are used ifthe
formation is hard or if the fishis embedded in the formation.Use of
these two designs also cutsaway protruding excess metal toallow
free entry of the junk intothe basket.
Finger Shoe - For retrievingloose junk on the bottom of thehole
which may exceed the maxi-mum catch of the RCB can beretrieved by
use of a finger shoeassembly. The assembly consistsof a shoe
extension and the fingerreplacement. The entire assemblyis used in
place of a mill shoe.The fingers are designed to closein beneath
the fish when slowlylowered during rotation. Fingerreplacements can
be replaced eas-ily and are very inexpensive.
Magnet Inserts - The RCBcan be easily converted to a fish-ing
magnet by removing thecatcher assembly and replacing itwith a
magnet insert. The insertstill allows direct or reverse
circu-lation and can be used with A, Bor C type shoes, or special
shoesdesigned to customer specifica-tions. The magnet insert is
thesame design as the Gotco FishingMagnet and by adding a top subto
the magnet insert, it can beused independently as a
fishingmagnet.
Reverse CirculatingJunk Basket
Catcher
-
Reverse Circulating Junk Basket Junk Catchers
www.gotco-usa.com 23
Reverse Circulating Junk Basket StandardHole Size 33/4 -4 41/8
-41/2 45/8 -5 51/8 -51/2 55/8 -6 61/8 -61/2 65/8 -73/8 71/2-
81/4Barrel OD 35/8 4 41/2 47/8 51/8 53/4 61/4 7Fish Dia., Max.
211/32 217/32 31/16 39/16 33/4 413/32 43/4 53/16No. of Mill Teeth 6
6 8 8 8 8 8 8Gotco Complete Part No. RCB-050 RCB-1 RCB-2 RCB-3
RCB-41 RCB-4 RCB-42 RCB-5Assembly XRef No. 6635 7295 4448 4572 2618
2670 2677 2554Replacement PartsTop Sub Part No. RCB-050-1 RCB-1-1
RCB-2-1 RCB-3-1 RCB-41-1 RCB-4-1 RCB-42-1 RCB-5-1
XRef No. 6636 7296 4449 4573 2619 2671 2678 2493Barrel Part No.
RCB-050-2 RCB-1-2 RCB-2-2 RCB-3-2 RCB-41-2 RCB-4-2 RCB-42-2
RCB-5-2
XRef No. 6637 7297 4450 4574 2620 2672 2679 2555Valve Cup Part
No. RCB-050-3 RCB-1-3 RCB-2-3 RCB-3-3 RCB-41-3 RCB-4-3 RCB-42-3
RCB-5-3
XRef No. 6638 6638 4451 4451 2621 2621 2621 2570Steel Ball Part
No. RCB-050-4 RCB-1-4 RCB-2-4 RCB-3-4 RCB-41-4 RCB-4-4 RCB-42-4
RCB-5-4
XRef No. 6640 6640 4453 4453 2623 2623 2623 2572Valve Seat Part
No. RCB-050-5 RCB-1-5 RCB-2-5 RCB-3-5 RCB-41-5 RCB-4-5 RCB-42-5
RCB-5-5
XRef No. 6639 6639 4452 4452 2622 2622 2622 2571Lifting Sub Part
No. RCB-050-6 RCB-1-6 RCB-2-6 RCB-3-6 RCB-41-6 RCB-4-6 RCB-42-6
RCB-5-6
XRef No. 4568 4568 424 424 425 425 1849 1849Junk Catcher Part
No. RCB-050-7 RCB-1-7 RCB-2-7 RCB-3-7 RCB-41-7 RCB-4-7 RCB-42-7
RCB-5-7
XRef No. 21795W 21855W 21780W 21790W 21735W 28349W 21750W
21725WMill Shoe, Type A Part No. RCB-050-8ARCB-1-8A RCB-2-8A
RCB-3-8A RCB-41-8A RCB-4-8A RCB-42-8A RCB-5-8A
XRef No. 6642A 7299A 4455A 4576A 2625A 2676A 2683A 2556AMill
Shoe, Type B Part No. RCB-050-8BRCB-1-8B RCB-2-8B RCB-3-8B
RCB-41-8B RCB-4-8B RCB-42-8B RCB-5-8B
XRef No. 6642B 7299B 4455B 4576B 2625B 2676B 2683B 2556BMill
Shoe, Type C Part No. RCB-050-8CRCB-1-8C RCB-2-8C RCB-3-8C
RCB-41-8C RCB-4-8C RCB-42-8C RCB-5-8C
XRef No. 6642C 7299C 4455C 4576C 2625C 2676C 2683C 2556C
Reverse Circulating Junk Basket StandardHole Size 83/8-91/2
95/8-105/8 103/4-115/8 113/4-121/2 125/8-135/8 133/4-16
16-171/2Barrel OD 77/8 91/8 101/8 11 117/8 13 15Fish Dia., Max.
61/16 71/16 711/16 85/16 811/16 97/8 111/8No. of Mill Teeth 8 10 12
12 14 16Gotco Complete Part No. RCB-6 RCB-8 RCB-9 RCB-10 RCB-11
RCB-12 RCB-13Assembly XRef No. 2567 2659 2684 2690 2696 2702
2708Replacement PartsTop Sub Part No. RCB-6-1 RCB-8-1 RCB-9-1
RCB-10-1 RCB-11-1 RCB-12-1 RCB-13-1
XRef No. 2568 2660 2685 2691 2697 2703 2709Barrel Part No.
RCB-6-2 RCB-8-2 RCB-9-2 RCB-10-2 RCB-11-2 RCB-12-2 RCB-13-2
XRef No. 2569 2661 2686 2692 2698 2704 2710Valve Cup Part No.
RCB-6-3 RCB-8-3 RCB-9-3 RCB-10-3 RCB-11-3 RCB-12-3 RCB-13-3
XRef No. 2570 2662 2662 2662 2662 2662 2662Steel Ball Part No.
RCB-6-4 RCB-8-4 RCB-9-4 RCB-10-4 RCB-11-4 RCB-12-4 RCB-13-4
XRef No. 2572 2665 2665 2665 2665 2665 2665Valve Seat Part No.
RCB-6-5 RCB-8-5 RCB-9-5 RCB-10-5 RCB-11-5 RCB-12-5 RCB-13-5
XRef No. 2571 2663 2663 2663 2663 2663 2663Lifting Sub Part No.
RCB-6-6 RCB-8-6 RCB-9-6 RCB-10-6 RCB-11-6 RCB-12-6 RCB-13-6
XRef No. 426 427 427 427 427 427 427Junk Catcher Part No.
RCB-6-7 RCB-8-7 RCB-9-7 RCB-10-7 RCB-11-7 RCB-12-7 RCB-13-7
XRef No. 18725W 14633W 18945W 21760W 21840W 21770W 21775WMill
Shoe, Type A Part No. RCB-6-8A RCB-8-8A RCB-9-8A RCB-10-8A
RCB-11-8A RCB-12-8A RCB-13-8A
XRef No. 2574A 2668A 2689A 2695A 2701A 2707A 2713AMill Shoe,
Type B Part No. RCB-6-8B RCB-8-8B RCB-9-8B RCB-10-8B RCB-11-8B
RCB-12-8B RCB-13-8B
XRef No. 2574B 2668B 2689B 2695B 2701B 2707B 2713BMill Shoe,
Type C Part No. RCB-6-8C RCB-8-8C RCB-9-8C RCB-10-8C RCB-11-8C
RCB-12-8C RCB-13-8C
XRef No. 2574C 2668C 2689C 2695C 2701C 2707C 2713C
Lift Sub
B Shoe
C Shoe
-
Junk Catchers Jet Type Junk Basket
www.gotco-usa.com24
TopSub
Gap Spring
Shear Pins
Seals, Pump Head
Jet Pump Head
Jet Nozzles
Ball Seat
Seals, Ball Seat
Jet BarrelFilter Nozzle
Lower Barrel
Cather Assembly
Shoe
Construction
The tool consists of a topsub, jet barrel, lower barrel,
jetassembly section, jets, ballseat, drop ball, shoe, andcatcher
assembly. A lift sub isavailable to assist in handlingand for
storage of the steeldrop ball.
Assembly and Operation
Make up the junk basket tothe bottom of the string andrun into
the hole. (see figure1) When the tool is approxi-mately 4 to 6 feet
off the bot-tom of the hole, circulation isinitiated to wash the
hole inorder to retrieve junk. Duringthis operation, the ball seat
issecured in place within theupper portion of the jet pumphead with
shear pins. Thisseals off the reverse circula-tion jet ports
providing full cir-culation through the entirelength of the tool.
The barrel,jet assembly, and junk catcherswill be washed clean
goinginto the hole while preparingfor junk retrieval.
When the tool is over thefish (junk), the steel drop ballis then
dropped through theinside diameter and seatsinside the ball seat.
(see figure2) When pump pressure isapplied, the pins will shear
allowing the ball seat to dropdown into the lower section ofthe
jet pump head. The flowwill now be directed out of thejet nozzles
at an angle as to notwashout the hole. Flow willthen be directed
downwardand back up through the junkbasket catcher, lower
barrel,jet housing, around the jetnozzles, and back out of the
jetbarrel ports. Thus, creatingreverse circulation and direct-ing
junk into the catcherassembly.
The Jet Type Junk Basketcan easily be converted to astandard
Core Basket by sim-ply removing the Jet Barreland Jet Assembly and
screw-ing the Lower Barrel directlyto the Top Sub.
O.D. Conversion andAccessories
The Lower Barrel can bereplaced by an oversized bar-rel in order
to adapt to a largerjunk catcher assembly. Thereare four types of
mill shoesavailable to fit the Jet TypeJunk Basket. Type A, B,
C,and the Finger Type Shoe. Seestandard Shoes in ReverseCirculation
Junk BasketSection on page 22.
Jet Type JunkBasketThe Gotco Jet Type Junk Basket is designed to
recover objectsfrom the bottom of the well bore. This superior tool
removesitems such as slips, hand tools, rock bit cones, and any
othersmall pieces of junk from the well.
Jet Junk BasketFig 1
Jet Junk BasketReverse Flow
Fig 2
Sizes available upon request.
DropBall
-
Core-Type Junk Basket Junk Catchers
www.gotco-usa.com 25
Assembly and Operation
Make up the core basket tothe bottom of the string and run itin
the hole to a point several feetfrom the bottom. With direct
cir-culation, the coring action on thejunk proceeds until a 24 inch
coreis cut. The fingers in the uppercatcher break the core when
anupward strain is applied to thestring. The lower catcher
fingers
then form a close-fitting basketthat traps the core with
itsretrieved junk. As in the otherjunk basket designs, they are
freeto revolve within the shoe, thuseliminating finger
breakage.
Optional Componentsand Accessories
Three types of milling shoesare available for all core-type
bas-
Core-Type Junk BasketThe Gotco Core-Type Junk Basket is a junk
retrieval tooldesigned to retrieve all types of objects from the
bottom of thewell bore. This easy-to-use tool removes such items as
slips, handtools, and bit cones. The basic assembly consists of a
top sub,barrel, type A mill shoe, upper and lower catchers.
How to Order Gotco Core-Type Junk BasketsWhen ordering, please
specify:
Name and part number of assembly Top connection (box) Shoe type
and O.D.
Recommended Spares 2 Upper Catchers 2 Lower Catchers 2 Mill
Shoes
ket systems: Type A shoe withside wings, Type B shoe
withhard-faced Gotcoloy sinteredtungsten carbide, and Type C
shoewith flat bottom and Gotcoloy onthe inner and outer faces.
Magnet Inserts A magnetinsert can be used in place of thecatcher
assemblies, thus convert-ing the tool to a fishing magnet.
Finger Shoe A finger shoeis used to retrieve junk that maybe too
large to enter the catchers.
Gotco Core-Type Junk BasketHole Diameter 33/4 - 41/8 41/4 - 41/2
45/8 - 5 45/8 - 5 51/8 - 51/2 55/8 - 6Tool OD 35/8 31/4 37/8 37/8
41/4 51/8Maximum Fish Diameter 223/32 231/32 39/32 33/8 39/32
325/32Standard Shoe OD 35/8 - 41/8 41/16 - 41/2 41/2 - 5 41/2 - 5
47/8 - 51/2 51/8 - 53/4Gotco Assembly Part No. CB-362 CB-325 CB-387
CB-387-1 CB-425 CB-512
Gotco Core-Type Junk BasketHole Diameter 55/8 - 6 61/8 - 61/2
61/8 - 65/8 6 - 63/8 63/4 - 71/4 73/8 - 81/4Tool OD 43/4 53/4 51/8
51/8 53/4 61/2Maximum Fish Diameter 41/16 43/8 45/16 41/2 43/16
57/16Standard Shoe OD 53/8 - 6 53/4 - 61/2 57/8 - 65/8 57/8 - 63/8
61/4 - 71/4 71/8 - 81/4Gotco Assembly Part No. CB-475 CB-575
CB-512-1 CB-512-2 CB-575-1 CB-650
Gotco Core-Type Junk BasketHole Diameter 83/8 - 91/4 93/8 -
101/4 103/8 - 117/8 113/4 - 141/4 125/8 - 15 143/8 - 18Tool OD 71/2
81/2 93/8 103/8 113/8 133/4Maximum Fish Diameter 63/16 73/16 81/16
91/16 101/16 121/16Standard Shoe OD 81/8 - 91/4 91/8 - 101/4 101/8
- 117/8 111/4 - 141/4 121/4 - 15 141/2 - 18Gotco Assembly Part No.
CB-750 CB-850 CB-937 CB-1037 CB-1137 CB-1375
C Shoe
Catcher
Core-TypeJunk Basket
-
Junk Catchers Fishing Magnet
www.gotco-usa.com26
ConstructionThe fishing magnet is con-
structed from steel speciallyselected for its ability to
conductthe necessary magneto-motiveforces. The magnet element isone
of the most powerful perma-nent magnets available. Usedproperly, it
will never lose its
charge. A variety of shoes areavailable to accommodate
anyretrieval situation. Caution:Magnets are charged while in
theassembled state and should notbe disassembled. Disassembly
isdangerous and can cause seriousinjury due to the extreme
forcesgenerated by the magnet element.
Assembly and Operation
No assembly is required otherthan selecting the desired shoeand
installing it on the lower endof the magnet assembly. Make upthe
magnet assembly to the bot-tom of the fishing string. Run inthe
hole, and hold the magnet 6 to12 inches above the fish.Circulate
generously to washaway cuttings. Reduce circula-tion, lower the
magnet to the fish,and rotate slightly to obtain goodcontact. Cut
off circulation andlift the magnet from the hole.
Optional Componentsand Accessories
Guides A flush guide isassembled as standard equipment.Lipped
guides and mill guides arealso available. The lipped guideassists
the operator in centralizingthe fish to assure contact with
themagnet. The mill guide enablesthe operator to mill any soft
for-mation or settling, thus freeingthe debris at the bottom of
thehole.
Wire Line Adapter Anadapter is available to installbetween the
magnet and the cablehead or socket.
Magnet Charger TheGotco Magnet Charger providesthe highest
strength possible forrecharging your fishing magnets.While magnets
should not losetheir effectiveness during normalhandling and
operation, condi-tions exist which can reduce theircharge. Welding
a magnet sub-jects the magnet circuit to electri-cal current which
can adverselyaffect the charge. Similarly, stor-ing the magnet in
the vicinity ofelectric motors, or bringing mag-nets too close to
each other can bedetrimental to the magnetsstrength. Recharging is
quick andsimple. There is no limit to the
Fishing MagnetThe Gotco Fishing Magnet is a junk retrieval tool
designed toeffectively remove metal particles, shavings, and debris
from thebottom of the well bore. The process of retrieving small,
oddlyshaped objects is one of the most frequent and most
difficultfishing jobs. Typically, these objects are the result of
bit failuresthat leave cones and cutters in the hole, or are an
accumulation ofmill cuttings, or are simply accidental droppings of
unmillableobjects into the hole. In these cases, the fish is nearly
always anodd-shaped object that cannot be engaged in the normal
manner.Fishing magnets successfully remove these small objects
fromthe hole bottom. The tools design incorporates generous
circula-tion holes that wash away the cuttings and other debris
that other-wise would prevent contact with the magnet. Fishing
magnetscan be run on either wire line or pipe.
How to Order Gotco Fishing MagnetsWhen ordering, please
specify:
Name and part number of assembly. Connection, if
nonstandard.
number of times a magnet can berecharged, and with proper
han-dling a recharged magnet willretain maximum strength
indefi-nitely.
Keepers Keeper bars arerecommended when magnets arestored. They
are placed on theface of the magnet and will con-sume most of the
flux generatedby the magnet element. This willreduce the potential
for the attrac-tion of miscellaneous metal itemsor particles.
Keepers can be safelyand easily removed at any time.
Air Shipments If shippingby air, consult your freight
for-warder. Special handling isrequired by most airlines
whenshipping magnetized items.
Gotco Fishing MagnetsHole Size 1 - 11/4 15/8 - 51/2 2 - 23/4
23/8 - 31/4 23/4 - 35/8 3 - 33/4 31/4 - 41/8Tool OD 1 11/4 11/2
13/4 21/4 21/2 3Connection 5/8 -11 5/8 SR 5/8 SR 3/4 SR 3/4 SR 3/4
SR 23/8 TBGApprox. Pull, lb. 5-7 8-10 11-14 15-20 25-75 75-125
125-200Gotco Assembly FM-1 FM-2 FM-3 FM-4 FM-5 FM-6 FM-7
Gotco Fishing MagnetsHole Size 4 - 41/4 41/4-41/2 41/2 - 5 51/8
- 51/2 55/8 - 6 61/8 -61/2Tool OD 31/4 31/2 4 41/2 5 51/2Connection
23/8 TBG 23/8 Reg 23/8 Reg 27/8 Reg 27/8 Reg 31/2 RegApprox. Pull,
lb. 125-200 150-250 250-350 350-450 450-500 500-600Gotco Assembly
FM-8 FM-350 FM-9 FM-10 FM-11 FM-12
Gotco Fishing MagnetsHole Size 61/8 -61/2 65/8 -71/2 75/8 - 81/2
85/8 - 93/4 97/8 -113/8 101/2 - 117/8Tool OD 53/4 6 7 8 9
10Connection 31/2 Reg 31/2 Reg 41/2 Reg 41/2 Reg 65/8 Reg 65/8
RegApprox. Pull, lb. 500-600 600-700 800-1000 1000-1200 1200-1400
1400-1600Gotco Assembly FM-13 FM-14 FM-15 FM-16 FM-17 FM-18
Gotco Fishing MagnetsHole Size 113/4 - 13 121/4 - 14 15 - UP 17
- UP 19 24Tool OD 101/2 111/2 14 16 18 22Connection 65/8 Reg 65/8
Reg 65/8 Reg 65/8 Reg 75/8 Reg 75/8 RegApprox. Pull, lb. 1600-800
1800-2200 2500-3000 2500-3000 2500-3000 2500-3000Gotco Assembly
FM-19 FM-20 FM-21 FM-22 FM-23 FM-24
Fishing Magnet
-
Ditch Magnet, Impression Block Junk Catchers
www.gotco-usa.com 27
Operation
The magnet should be usedany time metal particles mayaccumulate
in the mud. This is arequired tool during milling andwashover
operations. Position themagnet in the mud return line
How to Order Gotco Ditch MagnetWhen ordering, please specify:
Part number Length, if nonstandard
Ditch MagnetThe Gotco Ditch Magnet is a junk retrieval tool
designed toremove metal particles from drilling mud. High quality
stainlesssteel is used to encapsulate a series of extra strength
magnet ele-ments assuring maximum pick-up capacity.
Gotco Ditch MagnetOverall Length 18 24" 30" 36"Ditch Magnet Part
No. DM-18 DM-24 DM-30 DM-36
before the shale shaker. Metalparticles passing by the
magnetwill then be caught and retained,protecting the shale shaker,
mudpumps and other costly compo-nents of the mud system.
Assembly and Operation
Make up the impressionblock to the bottom of the fishingstring.
Run into hole until impres-sion block is near top of fish.Slowly
lower pipe until makingcontact with fish. Do not rotate.Apply
weight to impression blockand then pull out of hole. Theimpression
made will assist theoperator in determining whattools are needed to
prepare andretrieve the fish.
Impression BlockThe Gotco Impression Block is an accessory tool
used to accu-rately determine the dimensions and configuration of
the upperend of a fish as well as to check its condition and
position in thewell bore. The soft lead lower end of the impression
block cap-tures an impression of the fish upon making contact.
Impressionblocks are manufactured with a pin connection up and a
layer ofsoft lead on the lower end of the tool. Circulation holes
will beprovided on request.
How to Order Gotco Impression BlocksWhen ordering, please
specify:
Name and part number of assembly. Connection. O.D., if
nonstandard.
Gotco Lead Impression BlocksOD not over 15/8" 21/4" 23/4" 43/4"
51/2" 53/4"Length 12 12 12 15 15 15Gotco Part No. IB-162 IB-225
IB-275 IB-475 IB-550 IB-575
Gotco Lead Impression BlocksOD not over 8" 81/2" 11" 111/2"
113/4" 12"Length 19 19 20 20 20 20Gotco Part No. IB-800 IB-850
IB-1100 IB-1150 IB-1175 IB-1200
Ditch Magnet
Impression Block
-
Junk Catchers Wireline Spear
www.gotco-usa.com28
ConstructionSpears are constructed of high
quality steel for strength and dura-bility. The upper end of the
toolhas a box connection and fishingneck. Two types of spears
areavailable. The standard wirelinespear is provided with
weldedbarbs. The collapsible wirelinespear has retracting barbs to
alloweasier entry into the wire withoutcompacting it further.
Serrationson the spear shank, inside the col-lapsible barb cavity,
furtherenhances the ability of the GotcoWireline Spear to retain
its grip onthe cable while tripping out.
Assembly and Operation
Make-up the spear to the bot-tom of the string. Run in the
hole.Upon reaching the wire to beretrieved, slowly lower the
spear,allowing the steel barbs to engagethe wire. It may be
necessary tolift and lower several times to besure the spear has
sufficientlyengaged the wire. Slight rotationmay also be required
to loosen thewire if it is severely compacted.The spear may then be
lifted fromthe hole, bringing the loose wirewith it.
Wireline SpearThe Gotco Wireline Spear is a simple easy to use
tool designed toretrieve wire line and wire rope from the well
bore.
How to Order Gotco Wireline SpearsWhen ordering, please
specify:
Name and part number. Connection, if nonstandard.
Gotco Wireline SpearNeck OD 31/8 33/4 41/4 51/2Total Length 6 6
6 8Standard Connection 23/8 Reg 27/8 Reg 31/2 Reg 41/2 RegStandard
Type Part No. WS-312 WS-375 WS-425 WS-550Collapsible Type Part No.
CWS-312 CWS-375 CWS-425 CWS-550
Gotco Wireline SpearNeck OD 61/4 63/4 73/4 87/8Total Length 8 8
10 10Standard Connection 41/2 IF 51/2 Reg 65/8 Reg 75/8 RegStandard
Type Part No. WS-625 WS-675 WS-775 WS-887Collapsible Type Part No.
CWS-625 CWS-675 CWS-775 CWS-887
CollapsibleWireline
Spear
Wireline Spear
