09 05 61 COMMON WORK RESULTS FOR FLOORING …bidroom.net/Poulos/Oprf1121/Specifications/Division...

09 05 61COMMON WORK RESULTS FOR FLOORING PREPARATION

213060.00 COMMON WORK RESULTS FOR FLOORING PREPARATION09 05 61 - 1

PART 1 GENERAL1.01 SECTION INCLUDES

A. This section applies to all floors identified in the contract documents as to receive the followingtypes of floor coverings:1. Thin-set ceramic tile and stone tile.2. Terrazzo floor tile.3. Poured epoxy flooring.

B. Removal of existing floor coverings.C. Preparation of new and existing concrete floor slabs for installation of floor coverings.D. Testing of concrete floor slabs for moisture and pH.E. Preparation of new and existing wood-based floors and subfloors for installation of new floor

coverings.1.02 RELATED REQUIREMENTS

A. Section 03 30 00 - Cast-In-Place Concrete: Limitations on curing requirements for newconcrete floor slabs.

B. Section 03 54 00 - Cast Underlayment: Self-leveling underlayment applied as remediationtreatment.

1.03 REFERENCESA. ASTM C109/C109M - Standard Test Method for Compressive Strength of Hydraulic Cement

Mortars (Using 2-in. or (50-mm) Cube Specimens); 2012.B. ASTM C472 - Standard Test Methods for Physical Testing of Gypsum, Gypsum Plasters and

Gypsum Concrete; 1999 (Reapproved 2009).C. ASTM F710 - Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring;

2011.D. ASTM F1869 - Standard Test Method for Measuring Moisture Vapor Emission Rate of Concrete

Subfloor Using Anhydrous Calcium Chloride; 2011.E. ASTM F2170 - Standard Test Method for Determining Relative Humidity in Concrete Floor

Slabs Using in situ Probes; 2011.F. RFCI (RWP) - Recommended Work Practices for Removal of Resilient Floor Coverings;

Resilient Floor Covering Institute; October 2011.1.04 ADMINISTRATIVE REQUIREMENTS

A. Coordinate scheduling of cleaning and testing, so that preliminary cleaning has been completedfor at least 24 hours prior to testing.

1.05 SUBMITTALSA. Visual Observation Report: For existing floor coverings to be removed.B. Floor Covering and Adhesive Manufacturers' Product Literature: For each specific combination

of substrate, floor covering, and adhesive to be used; showing:1. Moisture and pH limits and test methods.2. Manufacturer's required bond/compatibility test procedure.

C. Testing Agency's Report: Include:1. Description of areas tested; include floor plans and photographs if helpful.2. Summary of conditions encountered.3. Moisture and pH test reports.4. Copies of specified test methods.5. Recommendations for remediation of unsatisfactory surfaces.6. Submit report to Architect.7. Submit report not more than two business days after conclusion of testing.

D. Adhesive Bond and Compatibility Test Report.


E. Copy of RFCI Recommended Work Practices for Removal of Resilient Floor Coverings.1.06 QUALITY ASSURANCE

A. Moisture and pH testing shall be performed by an independent testing agency employed andpaid by Contractor.

B. Testing Agency Qualifications: Independent testing agency experienced in the types of testingspecified.1. Submit evidence of experience consisting of at least 3 test reports of the type required,

with project Owner's project contact information.C. Contractor's Responsibility Relating to Independent Agency Testing:

1. Provide access for and cooperate with testing agency.2. Confirm date of start of testing at least 10 days prior to actual start.3. Allow at least 4 business days on site for testing agency activities.4. Achieve and maintain specified ambient conditions.5. Notify Architect when specified ambient conditions have been achieved and when testing

will start.1.07 FIELD CONDITIONS

A. Maintain ambient temperature in spaces where concrete testing is being performed, and for atleast 48 hours prior to testing, at not less than 65 degrees F (18 degrees C) or more than 85degrees F (30 degrees C).

B. Maintain relative humidity in spaces where concrete testing is being performed, and for at least48 hours prior to testing, at not less than 40 percent and not more than 60 percent.

PART 2 PRODUCTS2.01 MATERIALS

A. Patching Compound: Floor covering manufacturer's recommended product, suitable forconditions, and compatible with adhesive and floor covering. In the absence of anyrecommendation from flooring manufacturer, provide a product with the followingcharacteristics:1. Cementitious moisture-, mildew-, and alkali-resistant compound, compatible with floor,

floor covering, and floor covering adhesive, and capable of being feathered to nothing atedges.

2. Latex or polyvinyl acetate additions are permitted; gypsum content is prohibited.3. Compressive Strength: 3000 psi, minimum, after 28 days, when tested in accordance with

ASTM C109/C109M or ASTM C472, whichever is appropriate.B. Alternate Flooring Adhesive: Floor covering manufacturer's recommended product, suitable for

the moisture and pH conditions present; low-VOC. In the absence of any recommendation fromflooring manufacturer, provide a product recommended by adhesive manufacturer as suitablefor substrate and floor covering and for conditions present.

C. Remedial Floor Coating: Single- or multi-layer coating or coating/overlay combination intendedby its manufacturer to resist water vapor transmission to degree sufficient to meet flooringmanufacturer's emission limits, resistant to the level of pH found, and suitable for adhesion offlooring without further treatment.1. Thickness: 1/8 inch (3 mm), maximum.2. If testing agency recommends any particular products, use one of those.

PART 3 EXECUTION3.01 CONCRETE SLAB PREPARATION

A. Perform following operations in the order indicated:1. Existing concrete slabs (on-grade and elevated) with existing floor coverings:

a. Visual observation of existing floor covering, for adhesion, water damage, alkalinedeposits, and other defects.

b. Removal of existing floor covering.


2. Preliminary cleaning.3. Moisture vapor emission tests; 3 tests in the first 1000 square feet (100 square meters)

and one test in each additional 1000 square feet (100 square meters), unless otherwiseindicated or required by flooring manufacturer.

4. Internal relative humidity tests; in same locations as moisture vapor emission tests, unlessotherwise indicated.

5. pH tests; in same locations as moisture vapor emission tests, unless otherwise indicated.6. Specified remediation, if required.7. Patching, smoothing, and leveling, as required.8. Other preparation specified.9. Adhesive bond and compatibility test.10. Protection.

B. Remediations:1. Active Water Leaks or Continuing Moisture Migration to Surface of Slab: Correct this

condition before doing any other remediation; re-test after correction.2. Excessive Moisture Emission or Relative Humidity: If an adhesive that is resistant to the

level of moisture present is available and acceptable to flooring manufacturer, use thatadhesive for installation of the flooring; if not, apply remedial floor coating over entiresuspect floor area.

3. Excessive pH: If remedial floor coating is necessary to address excessive moisture, noadditional remediation is required; if not, if an adhesive that is resistant to the level presentis available and acceptable to the flooring manufacturer, use that adhesive for installationof the flooring; otherwise, apply a skim coat of specified patching compound over entiresuspect floor area.

3.02 REMOVAL OF EXISTING FLOOR COVERINGSA. Comply with local, State, and federal regulations and recommendations of RFCI Recommended

Work Practices for Removal of Resilient Floor Coverings, as applicable to floor covering beingremoved.

B. Dispose of removed materials in accordance with local, State, and federal regulations and asspecified.

3.03 PRELIMINARY CLEANINGA. Clean floors of dust, solvents, paint, wax, oil, grease, asphalt, residual adhesive, adhesive

removers, film-forming curing compounds, sealing compounds, alkaline salts, excessivelaitance, mold, mildew, and other materials that might prevent adhesive bond.

B. Do not use solvents or other chemicals for cleaning.3.04 MOISTURE VAPOR EMISSION TESTING

A. Where the floor covering manufacturer's requirements conflict with either the referenced testmethod or this specification, comply with the manufacturer's requirements.

B. Where this specification conflicts with the referenced test method, comply with the requirementsof this section.

C. Test in accordance with ASTM F1869 and as follows.D. Plastic sheet test and mat bond test may not be substituted for the specified ASTM test method,

as those methods do not quantify the moisture content sufficiently.E. In the event that test values exceed floor covering manufacturer's limits, perform remediation as

indicated. In the absence of manufacturer limits, perform remediation if test values exceed 3pounds per 1000 square feet (1.4 kg per 93 square meters) per 24 hours.

F. Report: Report the information required by the test method.3.05 INTERNAL RELATIVE HUMIDITY TESTING



B. Where this specification conflicts with the referenced test method, comply with the requirementsof this section.

C. Test in accordance with ASTM F2170 Procedure A and as follows.D. Testing with electrical impedance or resistance apparatus may not be substituted for the

specified ASTM test method, as the values determined are not comparable to the ASTM testvalues and do not quantify the moisture content sufficiently.

E. In the event that test values exceed floor covering manufacturer's limits, perform remediation asindicated. In the absence of manufacturer limits, perform remediation if any test value exceeds75 percent relative humidity.

F. Report: Report the information required by the test method.3.06 PH TESTING


B. Note: This procedure is the equivalent of that described in ASTM F710, repeated here for theContractor's convenience.

C. Use a wide range pH paper, its associated chart, and distilled or deionized water.D. Place several drops of water on a clean surface of concrete, forming a puddle approximately 1

inch (25 mm) in diameter. Allow the puddle to set for approximately 60 seconds, then dip thepH paper into the water, remove it, and compare immediately to chart to determine pH reading.

E. In the event that test values exceed floor covering manufacturer's limits, perform remediation asindicated. In the absence of manufacturer limits, perform remediation if any test value is over10.

3.07 PREPARATIONA. See individual floor covering section(s) for additional requirements.B. Comply with requirements and recommendations of floor covering manufacturer.C. Fill and smooth surface cracks, grooves, depressions, control joints and other non-moving

joints, and other irregularities with patching compound.D. Do not fill expansion joints, isolation joints, or other moving joints.

3.08 ADHESIVE BOND AND COMPATIBILITY TESTINGA. Comply with requirements and recommendations of floor covering manufacturer.

3.09 APPLICATION OF REMEDIAL FLOOR COATINGA. Comply with requirements and recommendations of coating manufacturer.

3.10 PROTECTIONA. Cover prepared floors with building paper or other durable covering.

END OF SECTION

09 21 16GYPSUM BOARD ASSEMBLIES

213060.00 GYPSUM BOARD ASSEMBLIES09 21 16 - 1


A. Performance criteria for gypsum board assemblies.B. Metal stud wall framing including shaft wall framing.C. Cementitious backer board for interior applications.D. Gypsum wallboard.E. Abuse resistant wallboard.F. Joint treatment and accessories.

1.02 RELATED REQUIREMENTSA. Section 06 10 00 - Rough Carpentry: Blocking and sheathing .B. Section 09 51 00 - Acoustical Ceilings.C. Section 09 66 45 - Terrazzo Tile: Underlayment.

1.03 REFERENCE STANDARDSA. AISI SG02-6 - 2001 edition of the Cold-Formed Steel Framing Header Design; American Iron

and Steel Institute; 2001.B. ANSI A108.11 - American National Standard for Interior Installation of Cementitious Backer

Units; 2012.1.C. ANSI A118.9 - American National Standard Specifications for Test Methods and Specifications

for Cementitious Backer Units; 2012.1.D. ASTM C475/C475M - Standard Specification for Joint Compound and Joint Tape for Finishing

Gypsum Board; 2012.E. ASTM C557 - Standard Specification for Adhesives for Fastening Gypsum Wallboard to Wood

Framing; 2003 (Reapproved 2009)e1.F. ASTM C645 - Standard Specification for Nonstructural Steel Framing Members; 2011a.G. ASTM C665 - Standard Specification for Mineral-Fiber Blanket Thermal Insulation for Light

Frame Construction and Manufactured Housing; 2012.H. ASTM C754 - Standard Specification for Installation of Steel Framing Members to Receive

Screw-Attached Gypsum Panel Products; 2011.I. ASTM C840 - Standard Specification for Application and Finishing of Gypsum Board; 2011.J. ASTM C954 - Standard Specification for Steel Drill Screws for the Application of Gypsum Panel

Products or Metal Plaster Bases to Steel Studs From 0.033 in. (0.84 mm) to 0.112 in. (2.84 mm)in Thickness; 2011.

K. ASTM C1002 - Standard Specification for Steel Self-Piercing Tapping Screws for theApplication of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs;2007.

L. ASTM C1047 - Standard Specification for Accessories for Gypsum Wallboard and GypsumVeneer Base; 2010a.

M. ASTM C1278/C1278M - Standard Specification for Fiber-Reinforced Gypsum Panel; 2007a(Reapproved 2011).

N. ASTM C1325 - Standard Specification for Non-Asbestos Fiber-Mat Reinforced CementSubstrate Sheets; 2008b.

O. ASTM C1396/C1396M - Standard Specification for Gypsum Board; 2011.P. ASTM C1629/C1629 - Standard Classification for Abuse-Resistant Nondecorated Interior

Gypsum Panel Products and Fiber-Reinforced Cement Panels; 2006.Q. ASTM D3273 - Standard Test Method for Resistance to Growth of Mold on the Surface of

Interior Coatings in an Environmental Chamber; 2012.


R. ASTM E72 - Standard Test Methods of Conducting Strength Tests of Panels for BuildingConstruction; 2010.

S. ASTM E90 - Standard Test Method for Laboratory Measurement of Airborne SoundTransmission Loss of Building Partitions and Elements; 2009.

T. ASTM E413 - Classification for Rating Sound Insulation; 2010.U. GA-600 - Fire Resistance Design Manual; Gypsum Association; 2012.

1.04 SUBMITTALSA. See Section 01 30 00 - Administrative Requirements, for submittal procedures.B. Product Data: Provide data on metal framing, gypsum board, accessories, and joint finishing

system.C. Test Reports: For all stud framing products that do not comply with ASTM C645 or C 754,

provide independent laboratory reports showing maximum stud heights at required spacingsand deflections.

1.05 QUALITY ASSURANCEA. Design framing elements under direct supervision of a Professional Structural Engineer

experienced in design of this Work and licensed in the State in which the Project is located.B. Comply with stud sizes as indicated on drawings. Design shall accomodate loads by increasing

stud material gage, the addition of bridging, strapping or other acceptable reinforcing as perAISI. Contact Architect immediately with regard to any design limitations based on stud size.

C. Perform in accordance with ASTM C 840. Comply with requirements of GA-600 for fire-ratedassemblies.

D. Installer Qualifications: Company specializing in performing gypsum board application andfinishing, with minimum 5 years of documented experience.

PART 2 PRODUCTS2.01 GYPSUM BOARD ASSEMBLIES

A. Provide completed assemblies complying with ASTM C840 and GA-216.B. Shaft Walls at HVAC Shafts: Provide completed assemblies with the following characteristics:

1. Air Pressure Within Shaft: Sustained loads of 5 lbf/sq ft (0.24 kPa) with maximummid-span deflection of L/240.

2. Acoustic Attenuation: STC of 35-39 calculated in accordance with ASTM E413, based ontests conducted in accordance with ASTM E90.

2.02 METAL FRAMING MATERIALSA. Manufacturers - Metal Framing, Connectors, and Accessories:

1. Clarkwestern Dietrich Building Systems LLC: www.clarkdietrich.com.2. Dietrich Metal Framing: www.dietrichindustries.com.3. Marino: www.marinoware.com.4. The Steel Network Inc: www.SteelNetwork.com.5. Telling Industries: www.tellingindustries.com.6. Substitutions: See Section 01 60 00 - Product Requirements.

B. Metal Framing Connectors and Accessories:1. Same manufacturer as framing.2. Bridging may be used to achieve design ratings provided that installed assemblies will not

interfere with MEP systems.3. Header and stud joining clips.4. Substitutions: See Section 01 60 00 - Product Requirements.

C. Non-Loadbearing Framing System Components: Comply with system description above;Design wall framing components to withstand listed design loads for wall type and actual loadsof face materials to be applied. All framing to conform to specified standards and to be


composed of the following: ASTM C 645; galvanized sheet steel, of minimum size andproperties necessary to comply with ASTM C 754 for the spacing indicated unless exceededherein, with maximum deflection of wall framing of L/360 at 5 psf (240 Pa). Abutting partitionand corner details of ASTM C 754 shall be superceded as described herein. All interior framingshall be a minimum of 0.346 inches in thickness unless design considerations require increasedthicknesses.1. Exception: The minimum metal thickness and section properties requirements of ASTM C

645 are waived provided steel of 40 ksi (275 MPa) minimum yield strength is used, themetal is continuously dimpled, the effective thickness is at least twice the base metalthickness, and maximum stud heights are determined by testing in accordance with ASTME 72 using assemblies specified by ASTM C 754.

2. Studs: C shaped , SG web section by the Steel Network, HDS section by Dietrich,3. Runners: U shaped, sized to match studs.4. Ceiling Channels: C shaped.5. Furring: Hat-shaped sections, minimum depth of 7/8 inch (22 mm).

D. Shaft Wall Studs and Accessories: ASTM C645; galvanized sheet steel, of size and propertiesnecessary to comply with ASTM C754 and specified performance requirements.

E. Ceiling Hangers: Type and size as specified in ASTM C754 for spacing required.2.03 BOARD MATERIALS

A. Manufacturers - Gypsum-Based Board:1. Georgia-Pacific Gypsum: www.gpgypsum.com.2. National Gypsum Company: www.nationalgypsum.com.3. USG Corporation: www.usg.com.4. Lafarge North America Inc.,Herndon, Virginia 20170 (703) 480-3600.5. Substitutions: See Section 01 60 00 - Product Requirements.

B. Gypsum Wallboard: Paper-faced gypsum panels as defined in ASTM C1396/C1396M; sizes tominimize joints in place; ends square cut.1. Application: Use for vertical surfaces and ceilings, unless otherwise indicated.2. At Assemblies Indicated with Fire-Rating: Use type required by indicated tested assembly;

if no tested assembly is indicated, use Type X board, UL or WH listed.3. Thickness:

a. Vertical Surfaces: 5/8 inch (16 mm).b. Ceilings: 1/2 inch (13 mm).c. Multi-Layer Assemblies: Thicknesses as indicated on drawings.

C. Impact-Rated Wallboard: Tested to Level 3 soft-body and hard-body impact in accordance withASTM C1629.1. Application: where indicated.2. Mold Resistance: Score of 10, when tested in accordance with ASTM D3273.3. Paper-Faced Type: Gypsum wallboard as defined in ASTM C1396/C1396M.4. Unfaced Type: Interior fiber-reinforced gypsum panels as defined in ASTM

C1278/C1278M.5. Thickness: 1/2 inch (13 mm).6. Edges: Square.7. Products:

a. USG Corporation; Fiberock Brand Panels--VHI Abuse-Resistant.D. Backing Board For Wet Areas:

1. Application: Surfaces behind tile in wet areas.2. Mold Resistance: Score of 10, when tested in accordance with ASTM D3273.3. ANSI Cement-Based Board: Non-gypsum-based; aggregated Portland cement panels

with glass fiber mesh embedded in front and back surfaces complying with ANSI A118.9 orASTM C1325.a. Thickness: 1/2 inch (13 mm).


E. Ceiling Board: Special sag-resistant gypsum ceiling board as defined in ASTM C1396/C1396M;sizes to minimize joints in place; ends square cut.1. Application: Ceilings, unless otherwise indicated.2. Thickness: 1/2 inch (13 mm).3. Edges: Tapered.

F. Abuse-Resistant Type: Gypsum wallboard especially formulated for increased impactresistance, with enhanced gypsum core and heavy duty face and back paper.1. Core Type: Regular.2. Thickness: 1/2 inch (13 mm).3. Edges: Tapered.4. Products:

a. National Gypsum Company; Gold Bond Hi-Impact Brand XP Wallboard.b. USG Corporation; Fiberock Brand Panels--VHI Abuse-Resistant.c. Substitutions: See Section 01 60 00 - Product Requirements.

G. Cementitious Backer Board for Interior Applications meeting the following requirements: 1/2inch (13 mm).1. Meeting or exceeding ASTM C13252. Meeting or exceeding ASTM E136 for noncombustability.3. High density, glass fiber reinforced both sides.4. Thickness: 1/2 inch.5. Size: 3 foot by 8 foot.

2.04 CEMENTITUIOUS BACKING PANELSA. Manufacturers

1. Custom Building Products; www.custombuildingproducts.com2. FinPan, Inc.; www.finpan.com3. United States Gypsum Co; www.usg.com4. Substitutions: See Section 01600 - Product Requirements.5. Cementitious Backer Board for interior applications: Meeting or exceeding ASTM C1186

Type A, Grade II aggregated Portland cement panels with glass fiber mesh embedded infront and back surfaces, 5/8 inch (16 mm) thick.

6. Application: Vertical surfaces behind thinset tile in wet areas2.05 ACCESSORIES

A. Acoustic Insulation: ASTM C 665; preformed glass fiber, friction fit type, unfaced. Thickness of3 inches unless indicated otherwise.

B. Finishing Accessories: ASTM C1047, galvanized steel or rolled zinc, unless otherwise indicated.1. Types: As detailed or required for finished appearance.2. Special Shapes: In addition to conventional cornerbead and control joints

a. At exposed panel edges provide U-bead.b. At intersection of gypsum wall board and suspended ceiling systems provide Acoustic

Molding as manufactured by Fry-Reglet Corporation (www.fryreglet.com).C. Joint Materials for gypsum based products: ASTM C 475 and as recommended by gypsum

board manufacturer for project conditions. Lack of control or expansion joints on drawings doesnot remove the Contractor's responsibility for providing such.1. Tape: 2 inch (50 mm) wide, coated glass fiber tape for joints and corners, except as

otherwise indicated.2. Tape: 2 inch (50 mm) wide, creased paper tape for joints and corners, except as otherwise

indicated.3. Ready-mixed vinyl-based joint compound.

D. Joint Materials for cement boards: As recommended by board manufacturer for projectconditions.


E. Screws for Attachment to Steel Members Less Than 0.03 inch (0.7 mm) In Thickness, to WoodMembers, and to Gypsum Board: ASTM C1002; self-piercing tapping type; cadmium-plated forexterior locations.

F. Screws for Attachment to Steel Members From 0.033 to 0.112 inch (0.8 to 2.8 mm) inThickness: ASTM C954; steel drill screws for application of gypsum board to loadbearing steelstuds.

G. Screws: ASTM C 1002; self-drilling type; cadmium-plated for exterior locations.H. Screws: ASTM C 954; steel drill screws for application of gypsum board to loadbearing steel

studs.I. Screws for cement board: As recommended by board manufacturer for project conditions.J. Anchorage to Substrate: Tie wire, nails, screws, and other metal supports, of type and size to

suit application; to rigidly secure materials in place.K. Adhesive for Attachment to Wood: ASTM C557.

PART 3 EXECUTION3.01 EXAMINATION

A. Verify that project conditions are appropriate for work of this section to commence.3.02 SHAFT WALL INSTALLATION

A. Shaft Wall Framing: Install in accordance with manufacturer's installation instructions.1. Install studs at spacing required to meet performance requirements.

B. Shaft Wall Liner: Cut panels to accurate dimension and install sequentially between specialfriction studs.

3.03 FRAMING INSTALLATIONA. Metal Framing: Comply with ASTM C 754 and manufacturer's instructions unless exceeded

herein.B. Studs: Space studs at 16 inches (400 mm) on center.

1. Extend stud framing through ceiling to structure above . Maintain clearance understructural building members to avoid deflection transfer to studs. Provide extended legceiling runners.

C. T intersections: Construct T intersections by using minimum of three studs with top, bottom andintermediate blocking or four full studs. Lock all walls/members together by fastening framingmembers together at 16 inches on center vertically. Walls secured through Gypsum materialsonly as per ASTM C 754 shall not be permitted.

D. Corners: Construct corners using minimum of three studs with top, bottom and intermediateblocking or four full studs. Lock all walls/members together by fastening framing memberstogether at 16 inches on center vertically. Walls secured through Gypsum materials only as perASTM C 754 shall not be permitted.

E. Blocking: Install blocking for support of plumbing fixtures, toilet partitions, wall cabinets, woodframe openings, toilet accessories, hardware, and other wall mounted items. Comply withSection 06 10 54 for wood blocking.

3.04 ACOUSTIC ACCESSORIES INSTALLATIONA. Acoustic Insulation: Place tightly within spaces, around cut openings, behind and around

electrical and mechanical items within partitions, and tight to items passing through partitions.B. Install all accessories with manufacturerC. Install gypsum board to structure above on both sides of wall in all locations to maintain

acoustic properties of partitions.


3.05 BOARD INSTALLATIONA. Comply with ASTM C 840. Install to minimize butt end joints, especially in highly visible

locations.B. Single-Layer: Install gypsum board in most economical direction, with ends and edges

occurring over firm bearing.1. Exception: Tapered edges to receive joint treatment at right angles to framing.

C. Cementitious Backing Board: Install over steel framing members and wood framing memberswhere indicated, in accordance with ANSI A108.11 and manufacturer's instructions.

D. Installation on Metal Framing: Use screws for attachment of all gypsum board .3.06 INSTALLATION OF TRIM AND ACCESSORIES

A. Control Joints: Place control joints consistent with lines of building spaces and as indicated.Lack of control or expansion joints on drawings does not remove the Contractor's responsibilityfor providing such. In the event no control joints are shown, contact the Architect for directionprior to commencing Work. The following general guidelines shall be considered.1. Not more than 30 feet (10 meters) apart on walls and ceilings over 50 feet (16 meters)

long.2. At exterior soffits, not more than 30 feet (10 meters) apart in both directions.3. Secure all metal trim and accessories governed by ASTM C 1047 with screw fasteners at

intervals recommended by manufacturer, but in no case greater than 12 inches on center.B. Corner Beads: Install at external corners, using longest practical lengths. Fasten corner beads

with screws placed at 16 inches on center vertically minimum; crimping or stapling is notpermissible.

C. Edge Trim: Install at locations where gypsum board abuts dissimilar materials and as indicated.Fasten edge trim beads with screws placed at 16 inches on center vertically minimum; crimpingor stapling is not permissible.

3.07 JOINT TREATMENTA. Stabilize building moisture level prior to finishing joints and allow materials to sufficiently

acclimate and stabilize prior to treating joints to prevent cracking due to high moisture content.Cracked joints, corners or other intersections shall be repaired at no cost to Owner.

B. Paper Faced Gypsum Board: Use fiberglass joint tape, bedded with ready-mixed vinyl-basedjoint compound and finished with ready-mixed vinyl-based joint compound.

C. Finish gypsum board in accordance with levels defined in ASTM C840, as follows:1. Level 4: Walls and ceilings to receive paint finish or wall coverings, unless otherwise

indicated.2. Level 1: Fire rated wall areas above finished ceilings, whether or not accessible in the

completed construction.D. Tape, fill, and sand exposed joints, edges, and corners to produce smooth surface ready to

receive finishes.1. Feather coats of joint compound so that camber is maximum 1/32 inch (0.8 mm).2. Taping, filling, and sanding is not required at surfaces behind adhesive applied ceramic tile

and fixed cabinetry.3. Taping, filling and sanding is not required at base layer of double layer applications.

E. Fill and finish joints and corners of cementitious backing board as recommended bymanufacturer.

3.08 TOLERANCESA. Maximum Variation of Finished Gypsum Board Surface from True Flatness: 1/8 inch in 10 feet

(3 mm in 3 m) in any direction.END OF SECTION

09 30 00TILING

213060.00 TILING09 30 00 - 1


A. Porcelain ceramic tile for floor applications.B. Porcelain ceramic tile for wall applications.C. Cementitious backer board as tile substrate.D. Coated glass mat backer board as tile substrate.E. Ceramic accessories.F. Porcelain ceramic trim.

1.02 RELATED REQUIREMENTSA. Section 03 54 00 - Cast Underlayment.for leveling and waterproofing requirements prior to

installation of porcelain ceramic floor tile.B. Section 07 90 05 - Joint Sealers.C. Section 09 05 61 - Common Work Results for Flooring Preparation.D. Section 09 21 16 - Gypsum Board Assemblies: Installation of tile backer board.E. Section 22 40 00 - Plumbing Fixtures.

1.03 REFERENCE STANDARDSA. ANSI A108 Series/A118 Series/A136.1 - American National Standard Specifications for the

Installation of Ceramic Tile (Compendium); 2012.1.B. ANSI A108.6 - American National Standard Specifications for Installation of Ceramic Tile with

Chemical Resistant, Water Cleanable Tile-Setting and -Grouting Epoxy; 2012.1.C. ANSI A108.9 - American National Standard Specifications for Installation of Ceramic Tile with

Modified Epoxy Emulsion Mortar/Grout; 2012.1.D. ANSI A108.10 - American National Standard Specifications for Installation of Grout in Tilework;

2012.1.E. ANSI A108.11 - American National Standard for Interior Installation of Cementitious Backer

Units; 2012.1.F. ANSI A108.12 - American National Standard for Installation of Ceramic Tile with EGP (Exterior

glue plywood) Latex-Portland Cement Mortar; 2012.1.G. ANSI A108.13 - American National Standard for Installation of Load Bearing, Bonded,

Waterproof Membranes for Thin-Set Ceramic Tile and Dimension Stone; 2012.1.H. ANSI A118.3 - American National Standard Specifications for Chemical Resistant, Water

Cleanable Tile Setting and -Grouting Epoxy and Water Cleanable Tile-Setting Epoxy Adhesive;2012.1.

I. ANSI A118.7 - American National Standard Specifications for Polymer Modified Cement Groutsfor Tile Installation; 2012.1.

J. ANSI A118.9 - American National Standard Specifications for Test Methods and Specificationsfor Cementitious Backer Units; 2012.1.

K. ANSI A136.1 - American National Standard for Organic Adhesives for Installation of CeramicTile; 2012.1.

L. ANSI A137.1 - American National Standard Specifications for Ceramic Tile; 2012.M. TCNA (HB) - Handbook for Ceramic, Glass, and Stone Tile Installation; 2012.

1.04 ADMINISTRATIVE REQUIREMENTSA. Preinstallation Meeting: Convene a preinstallation meeting one week before starting work of

this section; require attendance by all affected installers.

213060.00 TILING09 30 00 - 2

1.05 SUBMITTALSA. See Section 01 30 00 - Administrative Requirements, for submittal procedures.B. Product Data: Provide manufacturers' data sheets on tile, mortar, grout, and accessories.

Include instructions for using grouts and adhesives.C. Shop Drawings: Indicate tile layout, patterns, color arrangement, perimeter conditions, junctions

with dissimilar materials, control and expansion joints, ceramic accessories, and setting details.D. Samples: Mount tile and apply grout on two plywood panels, minimum 18 x 18 inches (450 x

450 mm) in size illustrating pattern, color variations, and grout joint size variations.E. Manufacturer's Certificate: Certify that products meet or exceed specified requirements.F. Maintenance Data: Include recommended cleaning methods, cleaning materials, stain removal

methods, and polishes and waxes.G. Maintenance Materials: Furnish the following for Owner's use in maintenance of project.

1. See Section 01 60 00 - Product Requirements, for additional provisions.2. Extra Tile: One un-opened carton of each size, color, and surface finish combination.

1.06 QUALITY ASSURANCEA. Maintain one copy of The Tile Council of North America Handbook and ANSI A108 Series/A118

Series on site.B. Manufacturer Qualifications: Company specializing in manufacturing the types of products

specified in this section, with minimum 5 years of documented experience.C. Installer Qualifications: Company specializing in performing tile installation, with minimum of 5

years of documented experience.1.07 MOCK-UP

A. See Section 01 40 00 - Quality Requirements, for general requirements for mock-up.B. Construct tile mock-up where indicated on the drawings, incorporating all components specified

for the location.1. Minimum size of mock-up is indicated on the drawings.2. Approved mock-up may remain as part of the Work.

1.08 DELIVERY, STORAGE, AND HANDLINGA. Protect adhesives from freezing or overheating in accordance with manufacturer's instructions.

1.09 FIELD CONDITIONSA. Do not install solvent-based products in an unventilated environment.B. Maintain ambient and substrate temperature of 50 degrees F (10 degrees C) during installation

of mortar materials.PART 2 PRODUCTS2.01 TILE

A. Manufacturers: All products by the same manufacturer.1. Dal-Tile Corporation: www.daltile.com.2. Substitutions: Not permitted.

B. Porcelain Ceramic Tile : , and as follows:1. Manufacturers:

a. Basis of Design:1) EC1 Colorbody Porcelain manufactured by Dal-Tile Corporation:

www.daltile.com .b. Substitutions: Not permitted.

2. General Characteristics:a. Moisture Absorption: 0 to 0.5 percent, when tested in accordance with ASTM C373.b. Breaking Strength: >400 pounds, when tested in accordance with ASTM C648.

213060.00 TILING09 30 00 - 3

c. Scratch Hardness: 7.0, when tested in accordance with ASTM MOHS.d. Chemical Resistance: Resistant, when tested in accordance with MOHS.e. Size and Shape: As specified herein and indicated on drawings.f. Edges: Square.g. Surface Finish: As specified herein.h. Colors: As specified herein.i. Trim Units: Matching surface bullnose shapes in sizes coordinated with field tile.

3. Porcelain Ceramic Tile: Type 1 and Type 2 designations are not used.4. Porcelain Ceramic Tile Type 3.

a. Application: Interior; Wall; Field tile.b. Color: "Bank" J101.c. Size and Shape: 12 inch x 24 inch (30.0 cm x 60.0 cm).d. Thicknes: 3/8 inch (9.53 mm).e. Finish: Honed.f. Coefficient of Friction: Wet: >= 0.50 / Dry: >= 0.60 when measured in accordance with

ASTM C1028.g. Installation Pattern: As indicated on drawings.

5. Porcelain Ceramic Tile Type 4.a. Application: Interior; Wall; Accent tile.b. Color: "Holborn" J102.c. Size and Shape: 6 inch x 24 Random Linear Accent (15.0 cm x 60.0 cm).d. Thicknes: 3/8 inch (9.53 mm).e. Finish: Combination.f. Coefficient of Friction: Wet: >= 0.60 / Dry: >= 0.70 when measured in accordance with


6. Porcelain Ceramic Tile Type 5.a. Application: Interior; Wall; Accent tile.b. Color: "Bank" J101.c. Size and Shape: 4 inch x 24 inch (10.0 cm x 60.0 cm) - Manufacturer's standard tile.d. Thicknes: 3/8 inch (9.53 mm).e. Finish: Polished.f. Coefficient of Friction: Wet: >= 0.50 / Dry: >= 0.60 when measured in accordance with


7. Porcelain Ceramic Tile Type 6.a. Application: Interior; Floor; Field tile.b. Color: "Docks" J103.c. Size and Shape: 24 inch x 24 inch (60.0 cm x 60.0 cm).d. Thicknes: 3/8 inch (9.53 mm).e. Finish: Unpolished.f. Coefficient of Friction: Wet: >= 0.60 / Dry: >= 0.70 when measured in accordance with


8. Porcelain Ceramic Tile Type 7.a. Application: Interior; Floor; Accent tile.b. Color: "Docks" J103.c. Size and Shape: 4 inch x 24 inch (10.0 cm x 60.0 cm).d. Thicknes: 3/8 inch (9.53 mm).e. Finish: Polished.f. Coefficient of Friction: Wet: >= 0.50 / Dry: >= 0.60 when measured in accordance with


213060.00 TILING09 30 00 - 4

2.02 TRIM AND ACCESSORIESA. Ceramic Accessories: Glazed finish, same color and finish as adjacent field tile; same

manufacturer as tile.B. Ceramic Trim: Matching bullnose ceramic shapes in sizes coordinated with field tile.

1. Applications: Use in the following locations:a. Open Edges: Bullnose.

2. Manufacturer: Same as for tile.2.03 EDGE-PROTECTION AND TRANSITION PROFILES

A. Manufacturers:1. Basis of Design:

a. Schluter Systems, Inc: www.schluter.com.2. Substitutions: See Section 01 60 00 - Product Requirements.

B. Floor Edge Transition (Type 1): Profile with sloped exposed surface, 1/4 inch (6 mm) deepchannel below exposed surface, integrated trapezoid-perforated anchoring leg, and integratedgrout joint spacer.1. Schluter Systems, Inc.; Product: Reno-TK: www.schluter.com.2. Material and Finish: Brushed Stainless Steel Type 304

2.04 SETTING MATERIALSA. Provide setting materials made by the same manufacturer as grout.B. Basis of Design:

1. Laticrete International, Inc: www.laticrete.com.C. Other Acceptable Manufacturers:

1. Custom Building Products: www.custombuildingproducts.com.2. Bostik Inc: www.bostik-us.com.3. Mapei Corporation: www.mapei.com.4. Merkrete, by Parex USA, Inc: www.merkrete.com.5. ProSpec, an Oldcastle brand: www.prospec.com.6. Substitutions: See Section 01 60 00 - Product Requirements.

D. Polymer Modified Thin-Set Mortars: ANSI A118.4 and ANSI A118.11.1. Application(s): Use this type where indicated and where no other type of thin-set mortar is

indicated.2. Basis of Design:

a. Laticrete 253 Gold manufactured by Laticrete International, Inc.: www.laticrete.com .2.05 GROUTS

A. Basis of Design:1. Laticrete International, Inc: www.laticrete.com.

B. Other Acceptable Manufacturers:1. Custom Building Products: www.custombuildingproducts.com.2. Bostik Inc: www.bostik-us.com.3. Mapei Corporation: www.mapei.com.4. Merkrete, by Parex USA, Inc; Merkrete Non-Sanded Color Grout: www.merkrete.com.5. ProSpec, an Oldcastle brand: www.prospec.com.6. Substitutions: See Section 01 60 00 - Product Requirements.

C. Polymer Modified Grout: ANSI A118.7 polymer modified cement grout.1. Applications: Where indicated.2. Use sanded grout for joints 1/8 inch wide and larger; use unsanded grout for joints less

than 1/8 inch wide.3. Color(s): As selected by Architect from manufacturer's full line.4. Basis of Design:

213060.00 TILING09 30 00 - 5

a. Laticrete PermaColor Grout manufactured by Laticrete International, Inc.:www.laticrete.com .

D. Epoxy Grout: ANSI A118.3; Lightweight, two component, 100% solids epoxy; Chemicalresistant and water-cleanable epoxy grout.1. Applications: Where indicated.2. Color(s): As scheduled.3. Basis of Design:

a. Laticrete SpectraLock Pro Grout manufactured by Laticrete International, Inc.:www.laticrete.com .

E. Grout Sealer: Liquid-applied, moisture and stain protection for existing or new Portland cementgrout.1. Composition: Water-based colorless silicone.2. Products:

a. Merkrete, by Parex USA, Inc; Merkrete Grout Sealer: www.merkrete.com.b. Substitutions: See Section 01 60 00 - Product Requirements.

2.06 THIN-SET ACCESSORY MATERIALSA. Refer to Section 03 54 00 - Cast Underlayment for leveling and waterproofing requirements

prior to installation of porcelain ceramic floor tile.B. Cementitious Backer Board: ANSI A118.9; High density, cementitious, glass fiber reinforced,

1/2 inch (13 mm) thick; 2 inch (50 mm) wide coated glass fiber tape for joints and corners.PART 3 EXECUTION3.01 EXAMINATION

A. Verify that sub-floor surfaces are smooth and flat within the tolerances specified for that type ofwork and are ready to receive tile.

B. Verify that wall surfaces are smooth and flat within the tolerances specified for that type of work,are dust-free, and are ready to receive tile.

C. Verify that sub-floor surfaces are dust-free and free of substances that could impair bonding ofsetting materials to sub-floor surfaces.

D. Verify that concrete sub-floor surfaces are ready for tile installation by testing for moistureemission rate and alkalinity; obtain instructions if test results are not within limits recommendedby tile manufacturer and setting materials manufacturer.

E. Verify that required floor-mounted utilities are in correct location.3.02 PREPARATION

A. Protect surrounding work from damage.B. Vacuum clean surfaces and damp clean.C. Seal substrate surface cracks with filler. Level existing substrate surfaces to acceptable

flatness tolerances.D. Install backer board in accordance with ANSI A108.11 and board manufacturer's instructions.

Tape joints and corners, cover with skim coat of setting material to a feather edge.E. Prepare substrate surfaces for adhesive installation in accordance with adhesive manufacturer's

instructions.3.03 INSTALLATION - GENERAL

A. Install tile, thresholds, and stair treads and grout in accordance with applicable requirements ofANSI A108.1 through A108.13, manufacturer's instructions, and The Tile Council of NorthAmerica Handbook recommendations.

B. Lay tile to pattern indicated. Do not interrupt tile pattern through openings.C. Cut and fit tile to penetrations through tile, leaving sealant joint space. Form corners and bases

neatly. Align floor joints.

213060.00 TILING09 30 00 - 6

D. Place tile joints uniform in width, subject to variance in tolerance allowed in tile size. Make groutjoints without voids, cracks, excess mortar or excess grout, or too little grout.

E. Form internal angles square and external angles bullnosed.F. Sound tile after setting. Replace hollow sounding units.G. Keep expansion joints free of adhesive or grout. Apply sealant to joints.H. Prior to grouting, allow installation to completely cure; minimum of 48 hours.I. Grout tile joints. J. Apply sealant to junction of tile and dissimilar materials and junction of dissimilar planes.

3.04 INSTALLATION - FLOORS - THIN-SET METHODSA. Over interior concrete substrates, install in accordance with The Tile Council of North America

Handbook Method F113, dry-set or latex-Portland cement bond coat, with epoxy grout, unlessotherwise indicated.1. Where epoxy bond coat and grout are indicated, install in accordance with The Tile

Council of North America Handbook Method F131.B. Grout tile joints using with epoxy grout.

3.05 INSTALLATION - WALL TILEA. Over cementitious backer units on studs, install in accordance with The Tile Council of North

America Handbook Method W244.B. Grout tile joints using with polymer modified grout.

3.06 CLEANINGA. Clean tile and grout surfaces.

3.07 PROTECTIONA. Do not permit traffic over finished floor surface for 4 days after installation.

3.08 SCHEDULEA. Porcelain Ceramic Tile:

1. Refer to drawings for tile type locations.B. Grout:

1. Epoxy Grouts: Use at all ceramic wall and floor tile installations.a. Color: Laticrete "Dusty Gray" #60.

2. Polymer Modified Grouts: Use at all raked mortar joints between structural glazed facingtile units.a. Color: Laticrete "Almond" #85.

C. Edge Protection and Transition Profiles:1. Floor Edge Transition Type 1: Provide between porcelain ceramic tile and abutting

terrrazzo tile.END OF SECTION

09 51 00ACOUSTICAL CEILINGS

213060.00 ACOUSTICAL CEILINGS09 51 00 - 1


A. Suspended metal grid ceiling system.B. Acoustical units.

1.02 RELATED REQUIREMENTSA. Section 09 21 16 - Gypsum Board Assemblies: Soffits.B. Section 28 31 00 - Fire Detection and Alarm: Fire alarm components in ceiling system.C. Section 23 37 00 - Air Outlets and Inlets: Air diffusion devices in ceiling.D. Section 26 51 00 - Interior Lighting: Light fixtures in ceiling system.

1.03 REFERENCE STANDARDSA. ASTM C635 - Standard Specification for the Manufacture, Performance, and Testing of Metal

Suspension Systems for Acoustical Tile and Lay-in Panel Ceilings; 2007.B. ASTM C636/C636M - Standard Practice for Installation of Metal Ceiling Suspension Systems for

Acoustical Tile and Lay-in Panels; 2008.C. ASTM E580/E580M - Standard Practice for Installation of Ceiling Suspension Systems for

Acoustical Tile and Lay-in Panels in Areas Subject to Earthquake Ground Motions; 2011.D. ASTM E1264 - Standard Classification for Acoustical Ceiling Products; 2008e1.E. NFPA 286 - Standard Methods of Fire Tests for Evaluating Contribution of Wall and Ceiling

Interior Finish to Room Fire Growth; 2011.F. UL (FRD) - Fire Resistance Directory; Underwriters Laboratories Inc.; current edition.

1.04 ADMINISTRATIVE REQUIREMENTSA. Sequence work to ensure acoustical ceilings are not installed until building is enclosed,

sufficient heat is provided, dust generating activities have terminated, and overhead work iscompleted, tested, and approved.

B. Do not install acoustical units until after interior wet work is dry.1.05 SUBMITTALS

A. See Section 01 30 00 - Administrative Requirements, for submittal procedures.B. Product Data: Provide data on suspension system components and acoustical units.C. Samples: Submit two samples 4 x 8 inch (101.6 x 101.6 mm) in size illustrating material and

finish of acoustical units.D. Samples: Submit two samples each, 6 inches (152.4 mm) long, of suspension system main

runner.E. Manufacturer's Installation Instructions: Indicate special procedures.F. Maintenance Materials: Furnish the following for Owner's use in maintenance of project.

1. See Section 01 60 00 - Product Requirements, for additional provisions.1.06 QUALITY ASSURANCE

A. Fire-Resistive Assemblies: Complete assembly listed and classified by UL for the fireresistance indicated.

B. Suspension System Manufacturer Qualifications: Company specializing in manufacturing theproducts specified in this section with minimum three years documented experience.

C. Acoustical Unit Manufacturer Qualifications: Company specializing in manufacturing theproducts specified in this section with minimum three years documented experience.

1.07 WARRANTY.A. Provide manufacturer's standard one-year warranty against defects in manufacturing and

workmanship.


1.08 EXTRA MATERIALSA. See Section 01 60 00 - Product Requirements, for additional provisions.B. Acoustical Units/Ceiling Tile: Provide one unopened carton for each type, finish and color

selected.1.09 FIELD CONDITIONS

A. Maintain uniform temperature of minimum 60 degrees F (16 degrees C), and maximumhumidity of 40 percent prior to, during, and after acoustical unit installation.

PART 2 PRODUCTS2.01 ACOUSTICAL UNITS

A. Manufacturers:1. As specified for each acoustical unit type.2. Substitutions: Not permitted.

B. Acoustical Units - General: ASTM E1264, Class A.1. Units for Installation in Fire-Rated Suspension System: Listed and classified for the

fire-resistive assembly the suspension system is a part of.C. Acoustical Tile Type 3: Painted mineral fiber, ASTM E1264 Type III, with to the following

characteristics:1. Applications: Replacement of existing "spline-type" ceiling tiles.2. Basis of Design:

a. USG; Product Radar Tile #2990: www.usg.com.b. Substitutions: Not permitted.

3. VOC Content: Certified as Low Emission by one of the following :a. Product listing in the CHPS Low-Emitting Materials Product List at;

www.chps.net/manual/lem_table.htm. 4. Size: 12 x 12 inches (300 x 300 mm).5. Thickness: 5/8 inches (15 mm).6. Composition: Water felted.7. Density: 0.61 to 1.15 lb/sq ft (2.98 to 5.61 kg/sq m)8. Light Reflectance:.085 percent, determined as specified in ASTM E1264.9. Noise Reduction Coefficient (NRC): 0.50, determined as specified in ASTM E1264.10. Ceiling Attenuation Class (CAC): 40 minimum, determined as specified in ASTM E1264.11. Recycled Content: 24 to 44 percent.12. Edge: Beveled.13. Surface Color: White.14. Surface Pattern: Non-directional fissured.15. Suspension System: Concealed grid Type 2.

D. Acoustical Panels Type 1: Painted mineral fiber, ASTM E1264 Type III, with the followingcharacteristics:1. Applications: Corridors, Classrooms, Offices, and where a panel type is not identified.2. Basis of Design:

a. Certainteed Corporation; Product Baroque Customline BQCL-224: www.usg.com.b. Substitutions: Not permitted.


www.chps.net/manual/lem_table.htm. 4. Size: 24 x 48 inches (600 x 1200 mm).

a. Surface Score: Center scored to give the appearance of two 24 x 24 inch tiles.5. Thickness: 3/4 inches (19 mm).6. Composition: Wet felted.7. Light Reflectance: 0.83 percent, determined as specified in ASTM E1264.8. Noise Reduction Coefficient (NRC): 0.83, determined as specified in ASTM E1264.


9. Ceiling Attenuation Class (CAC): 38, determined as specified in ASTM E1264.10. Recycled Content: 36 to 45 percent.11. Edge: Reveal edge.12. Surface Color: White.13. Surface Pattern: Non-directional fissured.14. Suspension System: Exposed grid Type 1.

E. Acoustical Panels Type 2: Vinyl faced gypsum board, ASTM E1264 Type XX, Pattern G withthe following characteristics:1. Applications: Toilet Rooms and Kitchens.2. Basis of Design:

a. USG; Product Sheetrock Lay-in Ceiling Panel ClimaPlus, Vinyl #32: www.usg.com.b. Substitutions: Not permitted.


www.chps.net/manual/lem_table.htm. 4. Size: 24 x 48 inches (600 x 1200 mm).5. Thickness: 1/2 inches (12.7 mm).6. Density: 2.0 lb/sq ft (9.76 kg/sq m).7. Light Reflectance: 0.77 percent, determined as specified in ASTM E1264.8. Noise Reduction Coefficient (NRC): n/a.9. Ceiling Attenuation Class (CAC): 35 minimum, determined as specified in ASTM E1264.10. Recycled Content: 40 percent.11. Abuse Resistant: Yes.12. Edge: Square.13. Surface Color: White.14. Surface Pattern: fine, smooth.15. Suspension System: Exposed grid Type 1.

2.02 SUSPENSION SYSTEM(S)A. Manufacturers:

1. Armstrong World Industries, Inc: www.armstrong.com.2. CertainTeed Corporation: www.certainteed.com.3. Chicago Metallic Corporation: www.chicagometallic.com.4. USG: www.usg.com.5. Substitutions: See Section 01 60 00 - Product Requirements.

B. Suspension Systems - General: ASTM C635; die cut and interlocking components, withstabilizer bars, clips, splices, perimeter moldings, and hold down clips as required.

C. Exposed Steel Suspension System Type 1: Formed steel, commercial quality cold rolled;intermediate-duty.1. Profile: Tee; 15/16 inch (24 mm) wide face.2. Construction: Double web.3. Finish: White painted.

D. Concealed Steel Suspension System Type 2: Formed steel, commercial quality cold rolled;intermediate-duty.1. Profile: Tee; 15/16 inch (24 mm) wide face.2. Construction: Double web.3. Finish: White painted.

2.03 ACCESSORIESA. Support Channels and Hangers: Galvanized steel; size and type to suit application, seismic

requirements, and ceiling system flatness requirement specified.B. Perimeter Moldings: Same material and finish as grid.

1. At Exposed Grid: Provide L-shaped molding for mounting at same elevation as face ofgrid.


2. At Concealed Grid: Provide exposed L-shaped molding.C. Touch-up Paint: Type and color to match acoustical and grid units.


A. Verify existing conditions before starting work.B. Verify that layout of hangers will not interfere with other work.

3.02 INSTALLATION - SUSPENSION SYSTEMA. Install suspension system in accordance with ASTM C636/C636M, ASTM E580/E580M, and

manufacturer's instructions and as supplemented in this section.B. Rigidly secure system, including integral mechanical and electrical components, for maximum

deflection of 1:360.C. Locate system on room axis according to reflected plan.D. Install after major above-ceiling work is complete. Coordinate the location of hangers with other

work.E. Hang suspension system independent of walls, columns, ducts, pipes and conduit. Where

carrying members are spliced, avoid visible displacement of face plane of adjacent members.F. Where ducts or other equipment prevent the regular spacing of hangers, reinforce the nearest

affected hangers and related carrying channels to span the extra distance.G. Do not support components on main runners or cross runners if weight causes total dead load

to exceed deflection capability.H. Support fixture loads using supplementary hangers located within 6 inches (150 mm) of each

corner, or support components independently.I. Do not eccentrically load system or induce rotation of runners.J. Perimeter Molding: Install at intersection of ceiling and vertical surfaces and at junctions with

other interruptions.1. Use longest practical lengths.2. Overlap and rivet corners.

3.03 INSTALLATION - ACOUSTICAL UNITSA. Install acoustical units in accordance with manufacturer's instructions.B. Fit acoustical units in place, free from damaged edges or other defects detrimental to

appearance and function.C. Fit border trim neatly against abutting surfaces.D. Install units after above-ceiling work is complete.E. Install acoustical units level, in uniform plane, and free from twist, warp, and dents.F. Cutting Acoustical Units:

1. Make field cut edges of same profile as factory edges.2. Double cut and field paint exposed reveal edges.

G. Where round obstructions occur, provide preformed closures to match perimeter molding.3.04 TOLERANCES

A. Maximum Variation from Flat and Level Surface: 1/8 inch in 10 feet (3 mm in 3 m).B. Maximum Variation from Plumb of Grid Members Caused by Eccentric Loads: 2 degrees.

3.05 SCHEDULEA. Corridors, Classrooms, and Offices: Tile/Panel Type 1.B. Toilet Rooms, Locker Rooms, Kitchens: Tile/Panel Type 2.


C. Patching or repair of existing spline ceilings: Tile/Panel Type 3.END OF SECTION

09 65 00RESILIENT FLOORING

213060.00 RESILIENT FLOORING09 65 00 - 1


A. Resilient tile flooring.B. Rubber wall base.C. Rubber stair treads and accessories.D. Transition strips.E. Subfloor preparation.F. Final cleaning and initial maintenance.

1.02 RELATED REQUIREMENTSA. Section 03 30 00 - Cast-in-Place Concrete: Restrictions on curing compounds for concrete

slabs and floors.B. Section 03 54 00 - Cast Underlayment.C. Section 09 05 61 - Common Work Results for Flooring Preparation: Independent agency

testing of concrete slabs, removal of existing floor coverings, cleaning, and preparation.1.03 REFERENCE STANDARDS

A. ASTM E 84 - Standard Test Method for Surface Burning Characteristics of Building Materials;1997a.

B. ASTM E648 - Standard Test Method for Critical Radiant Flux of Floor-Covering Systems Usinga Radiant Heat Energy Source; 2010e1.

C. ASTM F710 - Standard Practice for Preparing Concrete Floors to Receive Resilient Flooring;2011.

D. ASTM E 662 - Standard Test Method for Specific Optical Density of Smoke Generated by SolidMaterials; 1995.

E. ASTM F1066 - Standard Specification for Vinyl Composition Floor Tile; 2004 (Reapproved2010)e1.

F. ASTM F1344 - Standard Specification for Rubber Floor Tile; 2012.G. ASTM F 1482 - Standard Guide to Wood Underlayment Products Available for Use Under

Resilient FlooringH. ASTM F 1515 - Standard Test Method for Measuring Light Stability of Resilient Flooring by

Color Change.I. ASTM F1861 - Standard Specification for Resilient Wall Base; 2008 (Reapproved 2012).J. ASTM F 2169 - Standard Specification for Resilient Stair Treads.K. FS RR-T-650 - Treads, Metallic and Nonmetallic, Skid Resistant; Federal Specifications and

Standards; Revision E, 1994.L. RFCI (RWP) - Recommended Work Practices for Removal of Resilient Floor Coverings;

Resilient Floor Covering Institute; October 2011.1.04 SUBMITTALS

A. See Section 01 30 00 - Administrative Requirements, for submittal procedures.B. Product Data: Provide data on specified products, describing physical and performance

characteristics; including sizes, patterns and colors available; and installation instructions.C. Selection Samples: Submit two boxes of manufacturer's complete set of color samples for

each tile type specified for Architect's initial selection.D. Certification: Prior to installation of flooring, submit written certification by flooring manufacturer

and adhesive manufacturer that condition of sub-floor is acceptable.E. Maintenance Data: Include maintenance procedures, recommended maintenance materials,

and suggested schedule for cleaning, stripping, and re-waxing.


F. Maintenance Materials: Furnish the following for Owner's use in maintenance of project.1. See Section 01 60 00 - Product Requirements, for additional provisions.

1.05 DELIVERY, STORAGE, AND HANDLINGA. Deliver materials in labeled packages. Store and handle in strict compliance with manufacturer's

recommendations. Protect from damage due to weather, excessive temperatures, andconstruction operations.

B. Deliver materials sufficiently in advance of installation to condition materials to roomtemperature prior to installation.

C. Protect roll materials from damage by storing on end.1.06 QUALITY ASSURANCE

A. Manufacturer: Provide resilient flooring manufactured by a firm with a minimum of 10 yearsexperience in the fabrication of resilient flooring of types equivalent to those specified.Manufacturers proposed for use, which are not named in this Section, shall submit evidence ofability to meet performance requirements specified not less than 10 days prior to bid date.

B. Color Matching: Provide resilient flooring products, including wall base and accessories, fromone manufacturer to ensure color matching.

C. Manufacturer capable of providing field service representation.D. Installer's Qualifications: Installer experienced (minimum of 2 years) to perform work of this

section who has specialized in the installation of work similar to that required for this project andwho is acceptable to the product manufacturer.

E. Materials: For each type of material required for the work of this Section, provide primarymaterials which are the products of one manufacturer. Provide secondary materials which areacceptable to the manufacturer of the primary materials. Comply with applicable regulationsregarding VOC (volatile organic compound) content of adhesives.

1.07 FIELD CONDITIONSA. Maintain temperature in storage area between 55 degrees F and 90 degrees F.B. Store materials for not less than 48 hours prior to installation in area of installation at a

temperature of 70 degrees F to achieve temperature stability. Maintain a temperature of 68degrees F plus or minus 5 degrees F in spaces to receive resilient flooring. Specifiedtemperature shall be maintained at least 48 hours before, during, and 48 hours after installation.

1.08 WARRANTY.A. Provide manufacturer's standard one-year warranty against defects in manufacturing and

workmanship of resilient flooring products. Provide manufacturer's standard limited wearwarranty/conductivity warranty as specified under each product as applicable.

1.09 EXTRA MATERIALSA. See Section 01 60 00 - Product Requirements, for additional provisions.B. Resilient Floor Tile (VCT): Provide one unopened carton of each type and color selected.C. Resilient Floor Tile (VCT): Provide one unopened carton of each type and color selected.D. Resilient Floor Tile (VCT): Provide one unopened carton of each type and color selected.

PART 2 PRODUCTS2.01 MATERIALS - TILE FLOORING:

A. Vinyl Composition Tile: Homogeneous, with color extending throughout thickness, and:1. Minimum Requirements: Comply with ASTM F1066, of Class corresponding to type

specified.2. Size: 12 x 12 inch (305 x 305 mm).3. Thickness: 0.125 inch (3.2 mm).4. Manufacturers:


a. Armstrong World Industries, Inc: www.armstrong.com.1) Commercial Vinyl Composition Tile: Standard Excelon, Imperial Texture, or

Multi-Color Series.5. Other Acceptable Manufacturers:

a. Mannington Mills, Inc: www.mannington.com.b. Tarkett Inc: www.tarkett.com.c. Substitutions: See Section 01 60 00 - Product Requirements.

6. Architect will select from the Manufacturer's complete color line. Provide colors andpatterns as indicated on the drawings

B. Rubber Tile: Homogeneous color and pattern throughout thickness, and:1. Minimum Requirements: Comply with ASTM F1344, of Class corresponding to type

specified.2. Surface: Hammered.3. Color/Pattern: To be selected from the manufacturer's full range of colors.4. Back of Tile: Smooth, double sanded.5. Size: 39.53 x 39.53 inch (1004 x 1004 mm).6. Overall Thickness: 0.14 inch (3.5 mm).7. Pattern: Solid color.8. Limited Wear Warranty: 10 years.9. Hardness: ASTM D2240, Shore Type A, required > 75.10. Static Load: Per ASTM F970 Standard Test Method for Static Load Limit, residual

compression, when tested with 800 lbs, < 0.005”.11. Quality of Cut: ASTM F511 ? 0.005”.12. Squareness: ASTM F2055 ? 0.010”.13. ISO 14001: Manufacturer shall be ISO 14001 Environmental Management Systems

Certified14. PVC Free: Products shall contain no polyvinyl chloride.15. Abrasion Resistance: Taber abrasion test, ASTM D3389, H-18 wheel, 500 gram load,

1000 cycles, gram weight loss < 0.4.16. Slip Resistance: Static coefficient of friction (James Test): ASTM D2047, < 0.5.17. Bacteria Resistance: Products shall be resistant to bacteria, fungi, and micro-organism

activity, according to ASTM E2180 and ASTM G21.18. Acceptable Manufacturers:

a. Johnsonite, Inc; Product City Scape Rubber Speckled Tile, Color #577 'Two Step':www.johnsonite.com.

b. Substitutions: Not permitted.a. Substitutions: Not permitted.

2.02 STAIR COVERINGA. Stair Treads & Risers: Rubber; heavy duty, full width and depth of stair tread and risers in one

piece; tapered thickness; nosing not less than 1-5/8 inch (41 mm) deep.1. Basis of Design:

a. Fiesta Series Rubber Tile & Treads as manufactured by Roppe Corp., Fostoria OH.b. Substitutions: Not permitted.

2. Minimum Requirements: Comply with FS RR-T-650 requirements corresponding to typespecified.

3. Nominal Thickness: 0.100 inch (2.54 mm) - heavy duty.4. Nosing: Square.5. Style: Contrasting color abrasive grit strips full width, two strips per tread.6. Type: 1-smooth.7. Color: Marbleized.8. Width: Provide one-piece units across full width of stairs. Where stair width exceeds

available products, provide one seam down center of stair.9. Acceptable Manufacturers:


a. Johnsonite, Inc; Product Visually Impaired Hammered Tread Riser, Color #45'Sandalwood': www.johnsonite.com.

b. Substitutions: Not permitted.B. Tactile Warning Strips: 3/4" wide alternating 1/8" elevations and 1/16" depressions across at 12"

width. Co-extruded contrasting color alternating across profile surface. Comply with State ofIllinois Accessibility Code for detectable warning surface.1. Material: Rubber2. Nominal Thickness: 0.125 at elevations and 0.0625 at depressions3. Style: Ribbed, alternating elevations and depressions4. Color: Match stair treads and risers.5. Width: Provide one-piece units across full width of stairs. Where stair width exceeds

available products, provide one seam down center of stair.6. Manufacturer: Same as stair treads and risers.

2.03 RESILIENT BASEA. Same as stair treadsB. Resilient Base: ASTM F1861, Type TS rubber, vulcanized thermoset; top set Style B, Cove,

and as follows:1. Height: 4 inch (100 mm) and 6 inch (150 mm) as indicated on the drawings2. Thickness: 0.125 inch (3.2 mm) thick.3. Finish: Satin.4. Length: Roll.5. Color: Color as selected from manufacturer's standards.6. Accessories: Premolded external corners, internal corners, and end stops.7. Manufacturers:

a. Johnsonite, Inc: www.johnsonite.com.b. Roppe Corp., Fostoria, OH 44830.c. Nora: www.norarubber.comd. Substitutions: See Section 01 60 00 - Product Requirements.

2.04 TRANSITION STRIPSA. Rubber Transition Strips: ASTM F 1861, Type TS rubber, vulcanized thermoset, and as follows:

1. Profile: Two piece, as appropriate for the following conditions:a. Existing 1/8 inch resilient floor tile to new 3/16 inch terrazzo floor tile.b. New 1/8 inch rubber floor tile to new 3/16 inch terrazzo floor tile.

2. Finish: Satin.3. Length: Roll.4. Color: Color as selected from manufacturer's standards.5. Manufacturers:

a. Johnsonite, Inc: www.johnsonite.com.b. Roppe Corp., Fostoria, OH 44830.c. Nora: www.norarubber.comd. Substitutions: See Section 01 60 00 - Product Requirements.

B. Stair Metal Safety Edge:1. Approved Manufacturers:

a. Wooster Products, Inc., Wooster, OH:; Product Supergrit Type 132:www.wooster-products.com.

b. Substitutions: See Section 01 60 00 - Product Requirements.2. Metal Stair Edge: 3" wide by 1/4" thick, extruded 6063-T5 aluminum base with anti-slip

abrasive filler of contrasting color.a. Finish: Clear anodized aluminum.

C. Metal Divider and Expansion Strips:1. Approved Manufacturers:

a. Ceramic Tool Company, Pewaukee WI: www.ceramictool.com .


b. Substitutions: See Section 01 60 00 - Product Requirements.2. Divider Strips: Prefabricated joint consisting of one solid extruded aluminum T-shape.

Overall exposed width is 1/8 inch. Mechanically fasten to substrate.a. Acceptable Product: CTC Bar as manufactured by Ceramic Tool Company or

Architect approved equal.3. Control Joints: Prefabricated joint consisting of two solid extruded aluminum L-shaped

angles placed back-to-back. Overall exposed width is 1/4 inch. Mechanically fasten tosubstrate.a. Finish: Clear anodized aluminum.b. Acceptable Product: CTC Edge as manufactured by Ceramic Tool Company or

Architect approved equal.4. Expansion Joints: Prefabricated joint consisting of two solid extruded aluminum L-shaped

angles with factory installed two part polyurethane sealant 1/8-inch wide. Overall exposedwidth is 3/8 inch. Mechanically fasten to substrate.a. Finish: Clear anodized aluminum.b. Sealant Color: To be selected by Architect from manufacturer's full range of colors.c. Acceptable Product: CTC Joint as manufactured by Ceramic Tool Company or

Architect approved equal.2.05 ACCESSORIES

A. Subfloor Filler: Type recommended by adhesive material manufacturer.B. Primers, Adhesives, and Seaming Materials: Waterproof; types recommended by flooring

manufacturer.C. Filler for Coved Base: Plastic.D. Sealer and Wax: Types recommended by flooring manufacturer.


A. Verify that surfaces are flat to tolerances acceptable to flooring manufacturer, free of cracks thatmight telegraph through flooring, clean, dry, and free of curing compounds, surface hardeners,and other chemicals that might interfere with bonding of flooring to substrate.

B. Verify that sub-floor surfaces are smooth and flat within the tolerances specified for that type ofwork and are ready to receive resilient flooring.

C. Verify that wall surfaces are smooth and flat within the tolerances specified for that type of work,are dust-free, and are ready to receive resilient base.

D. Cementitious Sub-floor Surfaces: Verify that substrates are dry enough and ready for resilientflooring installation by testing for moisture and pH.1. Obtain instructions if test results are not within limits recommended by resilient flooring

manufacturer and adhesive materials manufacturer.E. Verify that concrete sub-floor surfaces are ready for resilient flooring installation by testing for

moisture emission rate and alkalinity; obtain instructions if test results are not within thefollowing limits:1. Moisture emission rate: Not greater than 3 lb per 1000 sq ft (7.1 kg per 100 sq m) per 24

hours when tested using calcium chloride moisture test kit for 72 hours.2. Alkalinity: pH range of 5-9.

F. Perform adhesive bond test in each major area, minimum 1 per 2,000 square feet, prior toinstallation. Examine after 72 hours to determine whether bond is solid and no moisture ispresent. Do not proceed with work until results of bond test are acceptable.

3.02 PREPARATIONA. Remove existing resilient flooring and flooring adhesives; follow the recommendations of RFCI

Recommended Work Practices for Removal of Resilient Floor Coverings.B. Prepare floor substrates as recommended by flooring and adhesive manufacturers.


C. Comply with ASTM F 710-92 and manufacturer's recommendations for surface preparation.Remove substances incompatible with resilient flooring adhesive by method acceptable tomanufacturer.

D. Concrete floors with steel troweled (slick) finish shall be properly roughened up (sanded) toensure suitable adhesion.

E. Concrete floors with curing, hardening, and breaking compounds shall be abraded withmechanical methods only to remove compounds. Use blastrac or similar equipment.

F. Remove sub-floor ridges and bumps. Fill minor low spots, cracks, joints, holes, and otherdefects with sub-floor filler to achieve smooth, flat, hard surface.

G. Fill voids, cracks, and depressions with trowel-applied leveling compounds acceptable tomanufacturer. Remove projections and repair other defects to tolerances acceptable tomanufacturer.

H. Prohibit traffic until filler is cured.I. Clean substrate by vacuuming subfloors immediately prior to installation to remove loose

particles.J. Provide cementitious self-leveling compound over entire area.

3.03 INSTALLATIONA. Starting installation constitutes acceptance of sub-floor conditions.B. Install in accordance with manufacturer's instructions.C. Spread only enough adhesive to permit installation of materials before initial set.D. Fit joints tightly.E. Set flooring in place, press with heavy roller to attain full adhesion.F. Where type of floor finish, pattern, or color are different on opposite sides of door, terminate

flooring under centerline of door.G. Install edge strips at unprotected or exposed edges, where flooring terminates, and where

indicated.1. Metal Strips: Attach to substrate before installation of flooring using stainless steel screws.2. Resilient Strips: Attach to substrate using adhesive.

H. Scribe flooring to walls, columns, cabinets, floor outlets, and other appurtenances to producetight joints.

I. Install flooring in recessed floor access covers, maintaining floor pattern.3.04 INSTALLATION - GENERAL

A. Install resilient flooring in accordance with manufacturer's printed installation instructions.B. Comply with the following:

1. Layout resilient flooring to provide equal size at perimeter. Adjust layout as necessary toeliminate resilient flooring which is cut to less than half full width.

2. Lay resilient flooring with arrows in the same direction.3. Install resilient flooring without cracks or voids at seams. Lay seams together without

stress. Remove excess adhesive immediately.4. Scribe resilient flooring neatly at perimeter and obstructions.5. Extend resilient flooring into reveals, closets, and similar openings.6. Install reducer strips at exposed edges.7. Do not mix manufacturing batches of a color within the same area.8. Do not install resilient flooring over building expansion joints.9. Do not install defective or damaged resilient flooring.

3.05 TILE FLOORINGA. Install in accordance with manufacturer's instructions.


B. Install tile in quarter turned manner.C. Mix tile from container to ensure shade variations are consistent when tile is placed, unless

manufacturer's instructions say otherwise.D. Spread only enough adhesive to permit installation of materials before initial set.E. Set flooring in place, press with heavy roller to attain full adhesion.F. Where floor finishes are different on opposite sides of door, terminate flooring under centerline

of door.G. Install edge strips at unprotected or exposed edges, where flooring terminates, and where

indicated. Before installation of flooring, secure metal strips with stainless steel screws.H. Scribe flooring to walls, columns, cabinets, floor outlets, and other appurtenances to produce

tight joints.3.06 RESILIENT BASE

A. Fit joints tightly and make vertical. Maintain minimum dimension of 18 inches (45 mm) betweenjoints.

B. Miter internal corners. At external corners, use premolded units. At exposed ends, usepremolded units.

C. Install base on solid backing. Bond tightly to wall and floor surfaces.D. Scribe and fit to door frames and other interruptions.

3.07 STAIR COVERINGSA. Install stair coverings in one piece for full width and depth of tread.B. Install stringers configured tightly to stair profile.C. Adhere over entire surface. Fit accurately and securely.

3.08 CLEANING & FINISHINGA. Remove excess adhesive from floor, base, and wall surfaces without damage.B. Clean in accordance with manufacturer's instructions including, but not limited to:

1. Sweep, mop, or vacuum the floor thoroughly to remove all loose dust and dirt.2. Remove excess adhesive.

C. Provide initial maintenance in accordance with manufacturer's instructions including, but notlimited to:1. Damp mop the floor with cleaner as recommended by manufacturer.2. Apply one coat stain-resistant sealer as recommended by manufacturer.3. Apply two coats of commercial floor polish as recommended by manufacturer.

3.09 PROTECTIONA. Protect the floor during installation as required to guard against damage to the new floor.B. Prohibit traffic on resilient flooring for 48 hours after installation.

END OF SECTION

09 66 45TERRAZZO TILE

213060.00 TERRAZZO TILE09 66 45 - 1


A. Marble terrazzo tile , for installation on existing:1. Concrete floors.2. Wood floors.

1.02 RELATED SECTIONSA. Section 03 54 00 - Cast Underlayment.B. Section 07 90 00 - Joint Sealers.C. Section 09 65 00 - Resilient Flooring: Rubber Wall Base, Stair Treads, Tactile-Warning Tile.

1.03 REFERENCESA. ASTM C 109/C 109M - Standard Test Method for Compressive Strength of Hydraulic Cement

Mortars (Using 2-in. or (50-mm) Cube Specimens); 2002.B. ASTM D 2047 - Standard Test Method for Static Coefficient of Friction of Polish-Coated Floor

Surfaces as Measured by the James Machine; 1999.C. ASTM E 84 - Standard Test Method for Surface Burning Characteristics of Building Materials;

2004.D. ASTM E 648 - Standard Test Method for Critical Radiant Flux of Floor-Covering Systems Using

a Radiant Heat Energy Source; 2003.E. ASTM E 662 - Standard Test Method for Specific Optical Density of Smoke Generated by Solid

Materials; 2003.F. ASTM F 510 - Standard Test Method for Resistance to Abrasion of Resilient Floor Coverings

Using an Abrader with a Grit Feed Method; 1993 (Reapproved 1999).G. MIL-D-3134 - Deck Covering Materials; Military Specifications and Standards; Revision J;

Amendment 1, 1989.1.04 SUBMITTALS

A. See Section 01 30 00 - Administrative Requirements, for submittal procedures.B. Product Data:

1. Manufacturer's product literature for terrazzo tile including installation instructions,maintenance requirements, and sample warranty.

2. Manufacturer's product literature for underlayment, patching compound, tile adhesive,sealer, and finish polish.

3. Perimeter sealant.4. Divider strips and expansion joints.

C. Selection Samples: Submit two boxes of manufacturer's complete set of color samples foreach tile type specified for the Architect's initial selection of colors.

D. Verification Samples: Provide two full sized samples of each color selected for final verificationof colors.

E. Installer Qualifications:1. Provide manufacturer's certificate indicating status as an approved installer.2. Provide documentation identifying minimum number of installations required including

project title, description of installation, contact person, and contact phone number.F. Maintenance Data: Manufacturer's printed cleaning and maintenance information.

1.05 QUALITY ASSURANCEA. Manufacturer Qualifications:

1. Regularly and presently manufacturing terrazzo tile meeting the requirements of theContract Documents.

2. Manufacturer shall have a minimum of ten years experience in the fabrication of terrazzotile and a minimum of ten documented installations in the last two years.

213060.00 TERRAZZO TILE09 66 45 - 2

B. Installer Qualifications:1. Having the technical qualifications, experience, trained personnel and facilities required to

properly execute the work.2. Minimum of five successful installations of the same manufacturer's tile within the last

three years.3. Certified by the terrazzo tile manufacturer as an approved installer.

1.06 DELIVERY, STORAGE, AND HANDLINGA. Deliver materials to jobsite in original unopened containers, free of damage, with manufacturer's

identification and brand name clearly marked.B. Store materials in a protected area, kept dry.C. Store on pallets complying with manufacturer's requirements, at not less than 40 degrees F (4

degrees C) nor more than 100 degrees F (38 degrees C).1.07 ENVIRONMENTAL REQUIREMENTS

A. Do not begin work until temperature at the site is at least 70 degrees F (21 degrees C), hasbeen maintained at that temperature for at least 48 hours, and will continue to be maintainedusing permanent heating systems.

B. Store materials on site at 70 degrees F (21 degrees C) for at least 48 hours prior to installation,separating tile boxes from pallets so as to allow tile to fully acclimate to ambient temperature.

1.08 WARRANTYA. See Section 01 78 00 - Closeout Submittals, for additional warranty requirements.B. Provide manufacturer's standard Twenty-Year warranty against wear.

1.09 EXTRA MATERIALSA. See Section 01 60 00 - Product Requirements, for additional provisions.B. Opened cartons containing unused materials shall be turned over to the Owner.C. Provide unopened cartons for each color selected as identified below:

1. Terrazzo Tile Type 1 (Field Color): Provide Four (4) unopened cartons.2. Terrazzo Tile Type 2 (Accent Color): Provide Two (2) unopened cartons.3. Terrazzo Tile Type 3 (Accent Color): Provide Two (2) unopened cartons.

PART 2 PRODUCTS2.01 MANUFACTURERS

A. Acceptable Manufacturers:B. Fritz Industries, Inc., Dallas TX (www.fritztile.com)

1. Local Sales Representative: Sustainable Flooring Sytems, Inc., Naperville IL(www.sustainableflooringsystems.com) (847) 426-9589.

C. Substitutions: Not permitted.2.02 ACCEPTABLE PRODUCTS

A. Provide Fritztile resilient flexible terrazzo tile.B. Acceptable Products:

1. Terrazzo Tile Type 1 (Field Color): "Canyon" #C520224.2. Terrazzo Tile Type 2 (Accent Color): "Greek Stone" #Q160504.3. Terrazzo Tile Type 3 (Accent Color): "Concourse" #C520210.

C. Substitutions: Not Permitted.2.03 MATERIALS

A. Terrazzo Tiles - Performance Requirements:1. Size: 12-inch x 12-inch.2. Thickness: 3/16-inch.

213060.00 TERRAZZO TILE09 66 45 - 3

3. Abrasion Resistance: Maximum 0.0196 cubic centimeters volume loss when tested inaccordance with ASTM F 510, Taber abrader, S-39 wheels, at 500 cycles with 1000 gramload.

4. Hardness:a. Binder Resin (matrix) casting "D" Hardness: 78 when tested in accordance with

ASTM-D 1706-61.b. Marble Barcol (aggregate) Hardness: 55-100 depending on pattern type.

5. Coefficient of Friction (slip resistance): Average 0.70 to 0.74 when tested in accordancewith ASTM D 2047.

6. Coefficient of Linear Thermal Expansion (between 30C and 30C): 1.3 x 10(-5).7. Compressive Strength: Between 2,900 psi and 5000 psi when tested in accordance with

ASTM C 109/C 109M.8. Electrical Characteristics: Non-conductive.9. Critical Radiant Flux: 0.93 watt/square centimeter (Class 1) when tested in accordance

with ASTM E 648.10. Smoke Density: Specific optical density of 231.76 (smoldering) and 292.05 (flaming) when

tested in accordance with ASTM E 662.11. Flame Spread: Compliance with Article 15, Part 1120 of State of New York Fire Building

Code - DOS File #09660-30507-400.12. Chemical Resistance: No change on surface, change in color, or swelling when tested in

accordance with ASTM F925-97.13. Water Absorption: 0.4 percent, maximum, when tested in accordance with MIL-D-3134F.14. Oil Resistance: Passes MIL-D-3134F.15. Corrosion Resistance: Passes MIL-D-3134F.16. Static Load Limit (Load at 125 lbs): Indentation of 0.0007-inches when tested in

accordance with ASTM F970-93.17. Squareness using Resilient Tile by Dial Gage Method: 0.003 when tested in accordance

with ASTM-F540-90.B. Tile Factory Finish: Permanent finish designed to accept topical protective coatings of the

acrylic dressing type.C. Underlayment Panels: Provide panels warranted for use as underlayment by the terrazzo tile

manufacturer. Fasten as required by the panel manufacturer for the project conditions.D. Patching Compounds: Cementitious or epoxy based products as recommended by the terrazzo

tile manufacturer after examination of the project conditions. Gypsum-based patchingcompounds not permitted.

E. Tile Adhesive: Products as manufactured by the terrazzo tile manufacturer and recommendedafter examination of the project conditions.

F. Perimter Sealant: Clear water-resistant silicone sealant.G. Floor Sealer: Product as manufactured by the terrazzo tile manufacturer and recommended

after examination of the project conditions.H. Gloss Floor Finish: Product as manufactured by the terrazzo tile manufacturer and

recommended after examination of the project conditions.I. Metal Transition and Edge Strips:

1. Approved Manufacturers:a. Ceramic Tool Company, Pewaukee WI: www.ceramictool.com .b. Substitutions: See Section 01 60 00 - Product Requirements.

2. Divider Strips: Prefabricated joint consisting of one solid extruded aluminum T-shape.Overall exposed width is 1/8 inch. Mechanically fasten to substrate.a. Acceptable Product: CTC Bar as manufactured by Ceramic Tool Company or

Architect approved equal.3. Control Joints: Prefabricated joint consisting of two solid extruded aluminum L-shaped

angles placed back-to-back. Overall exposed width is 1/4 inch. Mechanically fasten tosubstrate.

213060.00 TERRAZZO TILE09 66 45 - 4

a. Finish: Clear anodized aluminum.b. Acceptable Product: CTC Edge as manufactured by Ceramic Tool Company or

Architect approved equal.4. Expansion Joints: Prefabricated joint consisting of two solid extruded aluminum L-shaped

angles with factory installed two part polyurethane sealant 1/8-inch wide. Overall exposedwidth is 3/8 inch. Mechanically fasten to substrate.a. Finish: Clear anodized aluminum.b. Sealant Color: To be selected by Architect from manufacturer's full range of colors.c. Acceptable Product: CTC Joint as manufactured by Ceramic Tool Company or

Architect approved equal.PART 3 EXECUTION3.01 PROJECT CONDITIONS

A. Do not begin installation over concrete substrates until acceptable moisture conditions havebeen met; perform test for moisture emission as specified.

B. Verify that required flatness tolerances have been met. Substrates must be flat within 1/8 of aninch in 10 feet in all directions.

C. Do not proceed until unacceptable conditions have been corrected.D. Installation environment and the tile must be allowed to condition at 70-degrees F ambient or

higher, for at least 48 hours prior to installation. Maintain this temperature during and afterinstalling the tiles.

E. After delivery, remove tiles from the cartons and stack squarely upside down for a minimum of24 hours or until they are 70-degrees F and flat.

3.02 PREPARATIONA. Prepare substrates in accordance with the terrazzo tile manufacturer's instructions and

recommendations.B. Moisture Emission Test for Existing and New Concrete: Do not install terrazzo tile on concrete

which has moisture emission greater than the documented limitations published by the adhesivemanucturer.1. Before beginning test, shot-blast, scarify, or sand a small portion of the surface where test

will be conducted.2. Use an anhydrous calcium chloride 72 hour test unit and weigh within one hour of

completion of test. Test methods shall comply with ASTM F-1869.C. Where substrates have been chemically prepared, pH levels must be neutralized and the

substrate must be washed clean and allowed to dry.D. Existing Concrete:

1. Remove adhesives, mastics, and sealers completely and thoroughly. Use shot blasting,grinding, sanding, or chemical remover as required.

2. Clean off residues, grease, dirt, loose particles, projections, and all other foreign matterthat would prevent adhesion.

3. Fill joints, depressions, and irregularities with patching compound.E. Wood Substrates:

1. Cover with new underlayment; stagger joints to offset corners; fasten with screws atspacing recommended by manufacturer.

2. Fill joints and depressions with patching compound.F. Cementitious Backer Units:

1. Fill joints and depressions with specified patching compound.3.03 INSTALLATION

A. Install in accordance with tile manufacturer's instructions.B. Lay design symmetrically off center lines of corridors/rooms and as indicated on drawings.

213060.00 TERRAZZO TILE09 66 45 - 5

C. Cut tile to fit snugly at fixed vertical projections.D. Apply adhesives in accordance with directions as stated on the product package labels, set tile,

and remove spots and smears of adhesive immediately.E. Install divider strips, control joints, and expansion joints where indicated.F. Place each tile firmly into position. Butt each tile cleanly, evenly and snugly against adjacent tile.

Make joints tight, inconspicuous, and in true alignment.G. Roll tile into adhesive with 150 pound (68 kg) roller in direction diagonal to tile alignment until

adhesive has set and entire installation is flat and smooth. Roll tile in a direction diagonal to therun of the tiles. Continue rolling the floor until the adhesive has set and complete bonding of thetile and adhesive has occurred. Failure to roll the floor properly could result in adhesive bondfailure or high tile edges or high corners in the finished installation. Always lift the roller onto thenew installation. Do not roll the roller onto it.

H. Restrict foot traffic for 24 hours.I. Examine installation for excess adhesive, high tile edges, tile bond, and curling. Repair or

replace areas that are defective.J. Seal exposed perimeters with silicone to create a water barrier protecting the tile edges at the

installation perimeters.K. Clean, seal, and finish installation in accordance with terrazzo tile manufacturer's documented

recommnedations.3.04 PROTECTION

A. Keep all traffic off new floor installations for at least 24 hours after completion of installation.B. Install protective covering and maintain until project completion; do not apply masking tape

directly to tile. Remove covering at completion.3.05 CLEANING AND FINISHING PRIOR TO OCCUPANCY

A. After installation do not strip, flood, apply acids, alkaline cleansers, or wax - damage to thefactory finish will occur.

B. Clean and finish in accordance with the terrazzo tile manufacturer's documentedrecommnedations including, but not limited to, the following:1. Vacuum and/or dust mop with an untreated non-linting mop to remove all loose dust and

dirt.2. Damp mop using an all-purpose cleaner product and mixture as recommended by the

terrazzo tile manufacturer following all precautions on the product container.3. Rinse with clean water and let dry completely.4. Once the floor is completely dry, seal exposed perimeters with silicone to create a water

barrier protecting the tile edges at the installation perimeters.5. Apply two (2) very thin coats of floor sealer using a clean, non-linting rayon string mop

suitable for commercial installations. Allow each coat to dry completely before applyingadditional coats. Apply second coat of sealer in a direction perpendicular to the first coat.

6. Apply two (2) very thin coats of gloss floor finish using a clean non-linting rayon string mopsuitable for commercial installations. Allow each coat to dry completely before applyingadditional coats. Apply second coat of sealer in a direction perpendicular to the first coat.

7. After 48-hours cure time, burnish using a high speed burnisher.END OF SECTION

09 67 00FLUID-APPLIED FLOORING

213060.00 FLUID-APPLIED FLOORING09 67 00 - 1


A. Fluid-applied flooring and base.B. Divider strips and accessories.

1.02 RELATED REQUIREMENTSA. Section 03 54 00 - Cast UnderlaymentB. Section 07 90 05 - Joint Sealers: Joint between base and wall surface.

1.03 REFERENCE STANDARDSA. ASTM D570 - Standard Test Method for Water Absorption of Plastics; 1998 (Reapproved

2010).B. ASTM D638 - Standard Test Method for Tensile Properties of Plastics; 2010.C. ASTM D695 - Standard Test Method for Compressive Properties of Rigid Plastics; 2010.D. ASTM D905 - Standard Test Method for Strength Properties of Adhesive Bonds in Shear by

Compression Loading; 2008.E. ASTM D4060 - Standard Test Method for Abrasion Resistance of Organic Coatings by the

Taber Abraser; 2010.F. ASTM E84 - Standard Test Method for Surface Burning Characteristics of Building Materials;

2013a.G. ASTM E96/E96M - Standard Test Methods for Water Vapor Transmission of Materials; 2012.H. ASTM E648 - Standard Test Method for Critical Radiant Flux of Floor-Covering Systems Using

a Radiant Heat Energy Source; 2010e1.1.04 SUBMITTALS

A. See Section 01 30 00 - Administrative Requirements, for submittal procedures.B. Product Data: Provide data on specified products, describing physical and performance

characteristics; sizes, patterns and colors available .C. Samples: Submit two samples, 6 x 6 inch (152.4 x 152.4 mm) in size illustrating color and

pattern for each floor material for each color selected.D. Manufacturer's Installation Instructions: Indicate special procedures.E. Maintenance Data: Include maintenance procedures, recommended maintenance materials,

procedures for stain removal, repairing surface, and suggested schedule for cleaning.F. Maintenance Materials: Furnish the following for Owner's use in maintenance of project.

1. See Section 01 60 00 - Product Requirements, for additional provisions.2. Extra Flooring Material: 2 gallons (8 liters) of each color installed.

1.05 QUALITY ASSURANCEA. Manufacturer Qualifications: Company specializing in manufacturing products specified in this

section with minimum three years documented experience.B. Applicator Qualifications: Company specializing in performing work of this section with

minimum five years experience.C. Supervisor Qualifications: Trained by product manufacturer, under direct full time supervision of

manufacturer's own foreman.1.06 DELIVERY, STORAGE, AND HANDLING

A. Store resin materials in a dry, secure area.B. Store materials for three days prior to installation in area of installation to achieve temperature

stability.


1.07 FIELD CONDITIONSA. Maintain minimum temperature in storage area of 55 degrees F (13 degrees C).B. Store materials in area of installation for minimum period of 24 hours prior to installation.C. Maintain ambient temperature required by manufacturer 72 hours prior to, during, and 24 hours

after installation of materials.PART 2 PRODUCTS2.01 MANUFACTURERS

A. Fluid-Applied Flooring:1. Basis of Design (existing system already installed in facility):

a. Key Resin Company; Product Key Quartz B125: www.keyresin.com.2. Other Acceptable Manufacturers:

a. Manufacturer's other than the basis of design must exactly match the color, texture,pattern, etc. of the basis of design product.

b. Crossfield Products Corp: www.crossfieldproducts.com.c. Dex-O-Tex: www.dexotex.com.d. Sherwin-Williams Company: www.sherwin-williams.com/protective.e. BASF Construction Chemicals-Building Systems: www.buildingsystems.basf.com.

3. Substitutions: See Section 01 60 00 - Product Requirements.2.02 MATERIALS

A. Fluid-Applied Flooring Type EPXY-1: Epoxy, single component, thermosetting, colored withmineral filler, with aggregate embedded in base coat.1. Product: Key Quartz B125 manufactured by Key Resin Company.2. Base Coat: 1/8 inch (3 mm) thick; Match existing color.3. Aggregate: Small quartz chips, single color as selected.4. Top Coat: Epoxy, two component, thermosetting; clear; semi-gloss finish; apply two

coats.5. System Performance Properties:

a. Tensile Strength: 2,400 psi (0.10 MPa) when tested in accordance with ASTM C307.b. Compressive Strength: 11,500 psi (0.55 MPa) minimum when tested in accordance

with ASTM C579, 7 days.c. Flexural Strength: 4,300 psi (0.21 MPa) minimum when tested in accordance with

ASTM C580.d. Water Absorption: nil, when tested in accordance with ASTM D570 for 24 hours.e. Abrasion Resistance: Maximum weight loss of 32 mg/1000 cycles, when tested in

accordance with ASTM D4060.f. Flammability: Self extinguishing when tested in accordance with ASTM D635.g. Coefficent of Friction: 0.80when tested in accordance with ASTM D635.h. Mildew Resistance: No growth.

6. Joint Filler: Key Joint Filler #780 manufactured by Key Resin Company. Manufacturer toverify primer is appropriate for installation.

7. Primer: Key Primer/Low Modulus Binder #502 manufactured by Key Resin Company.Manufacturer to verify primer is appropriate for installation.

2.03 ACCESSORIESA. Subfloor Filler: White premix latex; type recommended by flooring material manufacturer.B. Primers and Adhesives: Waterproof; types recommended by flooring manufacturer.


A. Verify that sub-floor surfaces are smooth and flat within the tolerances specified for that type ofwork and are ready to receive flooring.


B. Verify that sub-floor surfaces are dust-free and free of substances that could impair bonding ofmaterials to sub-floor surfaces.

C. Verify that concrete sub-floor surfaces are ready for flooring installation by testing for moistureemission rate and alkalinity; obtain instructions if test results are not within the following limits:1. Moisture emission rate: Not greater than 3 lb per 1000 sq ft (7.1 kg per 100 sq m) per 24

hours when tested using calcium chloride moisture test kit for 72 hours.2. Alkalinity: pH range of 5-9.

D. Verify that required floor-mounted utilities are in correct location.3.02 PREPARATION

A. Remove sub-floor ridges and bumps. Fill low spots, cracks, joints, holes, and other defects withsub-floor filler.

B. Apply, trowel, and float filler to achieve smooth, flat, hard surface. Grind irregularities above thesurface level. Prohibit traffic until filler is cured.

C. Vacuum clean substrate.D. Apply primer to surfaces required by flooring manufacturer.

3.03 INSTALLATION - FLOORINGA. Apply in accordance with manufacturer's instructions.B. Apply each coat to minimum thickness indicated.C. Finish to smooth level surface.D. Cove at vertical surfaces.

3.04 PROTECTIONA. Prohibit traffic on floor finish for 48 hours after installation.B. Barricade area to protect flooring until cured.

3.05 SCHEDULEA. Refer to Finish Plan Drawings.

END OF SECTION

09 90 00PAINTING AND COATING

213060.00 PAINTING AND COATING09 90 00 - 1


A. Surface preparation.B. Field application of paints.C. Scope: Finish all interior and exterior surfaces exposed to view, unless fully factory-finished and

unless otherwise indicated.D. Do Not Paint or Finish the Following Items:

1. Items fully factory-finished unless specifically so indicated; materials and products havingfactory-applied primers are not considered factory finished.

2. Items indicated to receive other finishes.3. Items indicated to remain unfinished.4. Fire rating labels, equipment serial number and capacity labels, and operating parts of

equipment.5. Floors, unless specifically so indicated.6. Acoustical materials, unless specifically so indicated.7. Concealed pipes, ducts, and conduits.

1.02 RELATED REQUIREMENTSA. Section 09 21 16 - Gypsum Board Assemblies.

1.03 DEFINITIONSA. Conform to ASTM D16 for interpretation of terms used in this section.

1.04 REFERENCE STANDARDSA. 40 CFR 59, Subpart D - National Volatile Organic Compound Emission Standards for

Architectural Coatings; U.S. Environmental Protection Agency; current edition.B. ASTM D16 - Standard Terminology for Paint, Related Coatings, Materials, and Applications;

2012.C. ASTM D4442 - Standard Test Methods for Direct Moisture Content Measurement of Wood and

Wood-Base Materials; 2007.D. SSPC (PM1) - Good Painting Practice: SSPC Painting Manual, Vol. 1; Society for Protective

Coatings; Fourth Edition.1.05 SUBMITTALS

A. See Section 01 30 00 - Administrative Requirements, for submittal procedures.B. Samples: Submit two paper chip samples, 6 inch x 6 inch in size illustrating range of colors

available for each surface finishing product scheduled.C. Manufacturer's Instructions: Indicate special surface preparation procedures.D. Maintenance Data: Submit data on cleaning, touch-up, and repair of painted and coated

surfaces.1.06 QUALITY ASSURANCE

A. Manufacturer Qualifications: Company specializing in manufacturing the products specified,with minimum ten years documented experience.

1.07 DELIVERY, STORAGE, AND HANDLINGA. Deliver products to site in sealed and labeled containers; inspect to verify acceptability.B. Container Label: Include manufacturer's name, type of paint, brand name, lot number, brand

code, coverage, surface preparation, drying time, cleanup requirements, color designation, andinstructions for mixing and reducing.

C. Paint Materials: Store at minimum ambient temperature of 45 degrees F (7 degrees C) and amaximum of 90 degrees F (32 degrees C), in ventilated area, and as required by manufacturer'sinstructions.


1.08 FIELD CONDITIONSA. Do not apply materials when surface and ambient temperatures are outside the temperature

ranges required by the paint product manufacturer.B. Follow manufacturer's recommended procedures for producing best results, including testing of

substrates, moisture in substrates, and humidity and temperature limitations.C. Minimum Application Temperatures for Latex Paints: 45 degrees F (7 degrees C) for interiors;

50 degrees F (10 degrees C) for exterior; unless required otherwise by manufacturer'sinstructions.

D. Provide lighting level of 80 ft candles (860 lx) measured mid-height at substrate surface.PART 2 PRODUCTS2.01 MANUFACTURERS

A. Provide all paint and coating products used in any individual system from the samemanufacturer; no exceptions.

B. Paints:1. Benjamin Moore & Co: www.benjaminmoore.com.2. PPG Architectural Finishes, Inc: www.ppgaf.com.3. The Sherwin Williams, Company: www.sherwinwilliams.com.

C. Substitutions: See Section 01 60 00 - Product Requirements.2.02 PAINTS AND COATINGS - GENERAL

A. Paints and Coatings: Ready mixed, unless intended to be a field-catalyzed coating.1. Provide paints and coatings of a soft paste consistency, capable of being readily and

uniformly dispersed to a homogeneous coating, with good flow and brushing properties,and capable of drying or curing free of streaks or sags.

2. Supply each coating material in quantity required to complete entire project's work from asingle production run.

3. Do not reduce, thin, or dilute coatings or add materials to coatings unless such procedureis specifically described in manufacturer's product instructions.

B. Primers: Where the manufacturer offers options on primers for a particular substrate, useprimer categorized as "best" by the manufacturer.

C. Volatile Organic Compound (VOC) Content: 1. Provide coatings that comply with the most stringent requirements specified in the

following:a. 40 CFR 59, Subpart D--National Volatile Organic Compound Emission Standards for

Architectural Coatings.2. Determination of VOC Content: Testing and calculation in accordance with 40 CFR 59,

Subpart D (EPA Method 24), exclusive of colorants added to a tint base and water addedat project site; or other method acceptable to authorities having jurisdiction.

D. Colors: As indicated on drawings1. Allow for minimum of three colors for each system, unless otherwise indicated, without

additional cost to Owner.2.03 PAINT SYSTEMS - INTERIOR

A. Paint CI-OP-3L - Concrete/Masonry, Opaque, Latex, 3 Coat:1. One coat of block filler.2. Semi-gloss: Two coats of latex enamel; Color to be selected by Architect.

B. Paint MgI-OP-3L - Galvanized Metals, Latex, 3 Coat:1. One coat galvanize primer.2. Semi-gloss: Two coats of latex enamel; Color to be selected by Architect.

C. Paint CI-OP-3E - Concrete/Masonry, Epoxy Enamel, 3 Coat:1. One coat of catalyzed epoxy primer.


2. Gloss: Two coats of catalyzed epoxy enamel; Color to be selected by Architect.D. Paint GI-OP-3L - Gypsum Board/Plaster, Latex, 3 Coat:

1. One coat of alkyd primer sealer.2. Eggshell: Two coats of latex enamel; Color to be selected by Architect.3. Flat: Two coats of latex enamel; Color to be selected by Architect.

E. Previously Coated Surfaces, Latex, 3 Coat:1. One coat of alkyd primer sealer.2. Eggshell: Two coats of latex enamel; Color to be selected by Architect.3. Flat: Two coats of latex enamel; Color to be selected by Architect.

2.04 ACCESSORY MATERIALSA. Accessory Materials: Provide all primers, sealers, cleaning agents, cleaning cloths, sanding

materials, and clean-up materials required to achieve the finishes specified whether specificallyindicated or not; commercial quality.

B. Patching Material: Latex filler.C. Fastener Head Cover Material: Latex filler.


A. Verify that surfaces are ready to receive work as instructed by the product manufacturer.B. Examine surfaces scheduled to be finished prior to commencement of work. Report any

condition that may potentially affect proper application.C. Test shop-applied primer for compatibility with subsequent cover materials.D. Measure moisture content of surfaces using an electronic moisture meter. Do not apply finishes

unless moisture content of surfaces are below the following maximums:1. Gypsum Wallboard: 12 percent.2. Plaster and Stucco: 12 percent.3. Masonry, Concrete, and Concrete Unit Masonry: 12 percent.

3.02 PREPARATIONA. Clean surfaces thoroughly and correct defects prior to coating application.B. Prepare surfaces using the methods recommended by the manufacturer for achieving the best

result for the substrate under the project conditions.C. Remove or mask surface appurtenances, including electrical plates, hardware, light fixture trim,

escutcheons, and fittings, prior to preparing surfaces or finishing.D. Seal surfaces that might cause bleed through or staining of topcoat.E. Remove mildew from impervious surfaces by scrubbing with solution of tetra-sodium phosphate

and bleach. Rinse with clean water and allow surface to dry.F. Concrete and Unit Masonry Surfaces to be Painted: Remove dirt, loose mortar, scale, salt or

alkali powder, and other foreign matter. Remove oil and grease with a solution of tri-sodiumphosphate; rinse well and allow to dry. Remove stains caused by weathering of corrodingmetals with a solution of sodium metasilicate after thoroughly wetting with water. Allow to dry.

G. Gypsum Board Surfaces to be Painted: Fill minor defects with filler compound. Spot primedefects after repair.

H. Plaster Surfaces to be Painted: Fill hairline cracks, small holes, and imperfections with latexpatching plaster. Make smooth and flush with adjacent surfaces. Wash and neutralize highalkali surfaces.

3.03 APPLICATIONA. Remove unfinished louvers, grilles, covers, and access panels on mechanical and electrical

components and paint separately.


B. Apply products in accordance with manufacturer's instructions.C. Do not apply finishes to surfaces that are not dry. Allow applied coats to dry before next coat is

applied.D. Apply each coat to uniform appearance.E. Vacuum clean surfaces of loose particles. Use tack cloth to remove dust and particles just prior

to applying next coat.F. Reinstall electrical cover plates, hardware, light fixture trim, escutcheons, and fittings removed

prior to finishing.3.04 CLEANING

A. Collect waste material that could constitute a fire hazard, place in closed metal containers, andremove daily from site.

3.05 SCHEDULE - PAINT SYSTEMSA. Concrete, Concrete Block, Brick Masonry: Finish all surfaces exposed to view. Block fill for full

height of masonry.B. Gypsum Board: Finish all surfaces exposed to view.C. Wood Doors: WI-TR-VS.D. Steel Doors and Frames: Finish all surfaces exposed to view; MI-OP-3A, gloss.E. Steel Fabrications: Finish all surfaces exposed to view.

END OF SECTION

09 96 00HIGH-PERFORMANCE COATINGS

213060.00 HIGH-PERFORMANCE COATINGS09 96 00 - 1


A. High performance coatings.B. Special preparation of surfaces.

1.02 REFERENCE STANDARDSA. ASTM E84 - Standard Test Method for Surface Burning Characteristics of Building Materials;

2013a.B. SSPC-SP 2 - Hand Tool Cleaning; Society for Protective Coatings; 1982 (Ed. 2004).C. SSPC-SP 3 - Power Tool Cleaning; Society for Protective Coatings; 1982 (Ed. 2004).D. SSPC-SP 6 - Commercial Blast Cleaning; Society for Protective Coatings; 2007.E. SSPC-SP 11 - Power Tool Cleaning to Bare Metal; Society for Protective Coatings; 1987 (Ed.

2004).1.03 SUBMITTALS

A. See Section 01 30 00 - Administrative Requirements, for submittal procedures.B. Product Data: Provide data indicating coating materials .C. Samples: Submit two samples 2" x 2" inch (51 x 51 mm) in size illustrating colors available for

selection.D. Manufacturer's Installation Instructions: Indicate special procedures and perimeter conditions

requiring special attention.E. Manufacturer's Certificate: Certify that products meet or exceed specified requirements.F. Maintenance Data: Include cleaning procedures and repair and patching techniques.G. Maintenance Materials: Furnish the following for Owner's use in maintenance of project.

1. Extra Coating Materials: 1 gallon (4 liters) of each type and color.2. Label each container with manufacturer's name, product number, color number, and room

names and numbers where used.1.04 QUALITY ASSURANCE

A. Manufacturer Qualifications: Company specializing in manufacturing the Products specified inthis section with minimum ten years documented experience.

B. Applicator Qualifications: Company specializing in performing the work of this section withminimum three years documented experience.

1.05 FIELD CONDITIONSA. Do not install materials when temperature is below 55 degrees F (13 degrees C) or above 90

degrees F (32 degrees C).B. Maintain this temperature range, 24 hours before, during, and 72 hours after installation of

coating.C. Restrict traffic from area where coating is being applied or is curing.

1.06 WARRANTYA. See Section 01 78 00 - Closeout Submittals, for additional warranty requirements.

PART 2 PRODUCTS2.01 MANUFACTURERS

A. High-Performance Coatings:1. Basis of Design:

a. Tnemec Company, Inc; Product Enduratone Series 1029: www.tnemec.com.2. Approved Manufacturers:

a. Carboline Company: www.carboline.com.b. PPG Architectural Finishes, Inc: www.ppgaf.com.


c. Sherwin-Williams Company: www.protective.sherwin-williams.com/industries.3. Substitutions: Section 01 60 00 - Product Requirements.

2.02 HIGH-PERFORMANCE COATINGS2.03 MATERIALS

A. Coatings - General: Provide complete multi-coat systems formulated and recommended bymanufacturer for the applications indicated, in the thicknesses indicated; number of coatsspecified does not include primer or filler coat.

B. Mild Atmospheric Coating: Three coats, alkyd/acrylic/acrylic, minimum 6.0 to 9.5 mils (0.16 to0.25 mm) total dry film thickness.1. Surface Preparation: SSPC-SP6.2. Primer Coat Product: Series 10 manufactured by Tnemec Company, Inc.

a. Chemically active, rust-inhibitive primer.3. Intermediate Coat Product: Enduratone Series 1029 manufactured by Tnemec Company,

Inc.a. Water-based, low VOC, high dispersion, pure acrylic polymer coating; mildew

resistant.4. Finish Coat Product: Enduratone Series 1029 manufactured by Tnemec Company, Inc.

a. Water-based, low VOC, high dispersion, pure acrylic polymer coating; mildewresistant.

5. Color Coat: Solid color; color as selected.6. Top Coat: Clear, semi-gloss.

C. Primers: As recommended by coating manufacturer for specific substrate, unless otherwisespecified.

D. Shellac: Pure, white type.PART 3 EXECUTION3.01 EXAMINATION

A. Verify existing conditions before starting work.B. Verify that substrate surfaces are ready to receive work as instructed by the coating

manufacturer. Obtain and follow manufacturer's instructions for examination and testing ofsubstrates.

3.02 PREPARATIONA. Clean existing steel surfaces of loose foreign matter.B. Remove substances that would bleed through finished coatings. If unremovable, seal surface

with shellac.C. Existing Painted and Sealed Surfaces:

1. Remove loose, flaking, and peeling paint. Feather edge and sand smooth edges ofchipped paint.

2. Clean with mixture of trisodium phosphate and water to remove surface grease andforeign matter.

D. Galvanized Surfaces: Remove surface contamination and oils and wash with solvent.E. Ferrous Metal:

1. Remove loose rust, loose mill scale, and other foreign substances using hand toolsaccording to SSPC-SP 2 or power tools according to SSPC-SP 3.

2. Remove tight rust to bare metal using hand tools according to SSPC-SP 2 or power toolsaccording to SSPC-SP 3 or -SP 11 and protect from corrosion until coated.

F. Protect adjacent surfaces and materials not receiving coating from spatter and overspray; maskif necessary to provide adequate protection. Repair damage.


3.03 PRIMINGA. Apply primer to all surfaces, unless specifically not required by coating manufacturer. Apply in

accordance with coating manufacturer's instructions.3.04 COATING APPLICATION

A. Apply coatings in accordance with manufacturer's instructions, to thicknesses specified.B. Apply in uniform thickness coats, without runs, drips, pinholes, brush marks, or variations in

color, texture, or finish. Finish edges, crevices, corners, and other changes in dimension withfull coating thickness.

3.05 CLEANINGA. Collect waste material that could constitute a fire hazard, place in closed metal containers, and

remove daily from site.B. Clean surfaces immediately of overspray, splatter, and excess material.C. After coating has cured, clean and replace finish hardware, fixtures, and fittings previously

removed.3.06 PROTECTION

A. Protect finished work from damage.3.07 SCHEDULE

A. Exterior wall mounted clock hands and characters.END OF SECTION

Date post:	10-May-2020
Category:	Documents
Upload:	others
View:	19 times
Download:	0 times