1 |

INALA TECHNOLOGIESTEST PROCEDURE: ECS (E1/ETH), SAM2, SAM1.5 & ACCESS

VERSION 1.0

2 | SAM Training

TESTING SUMMARY

1. Set up SAM2.2. Set up ECS (E1/Eth) communication controller.3. Test communication to SAM1.5 or SAM2 unit via ECS (E1/Eth) coms Controller4. Test communication to Access Control unit via ECS (E1/Eth) coms Controller

3 |

SAM2 SET UP – VIA RS232

4 | SAM Training

SAM2 – RS232

RS232 Communication Test;• Connect a straight RS232 cable between the Lap Top and the

SAM2 RS232 port(DB9 Connector on front panel• Open SAM2 ECT

• Select “Com Port” and double click on “Password”

5 | SAM Training

SAM2 – SET UP VIA RS232 CONTINUED

RS232 Communication Test; Cont;• Active communication will be shown on the

bottom left as indicated with the RED circle until it says “received”

1. Click on “Load Config” and select the applicable config file.

2. Click on “Update SAM” and wait until SAM has been updated – This can be seen on the bottom left as indicated with the RED circle until it says “received”

3. Click on “Sync Time”4. Click on “Get Config” and ensure that

SAM2 shows you the current date and time.

5. Capture SAM2 Serial number.6. Click on “Update”7. Click on “Set Config”

12

3

4

5 6

7

6 | SAM Training

SAM2 – SET UP VIA RS232 CONTINUED

RS232 Communication Test; Cont;1. Click on “Alarm Configuration” tab2. Select “RS485” under “Coms Config”3. Click on “Set”4. Click on “Get Config”5. Click on “Set Config”

• Check that “Intruder” alarm is number “9”• Check that “Movement” alarm is number “11”

Close SAM2 ECT

1

23

45

7 |

ECS (E1/ETH) COMMUNICATION CONTROLLER SET-UP

8 | SAM Training

ECS(E1/ETH) COMS CONTROLLER – SET UP

ECS(E1/ETH) Coms Controller Set up;• Connect a Straight RS232 cable the Lap Top and the

ECS(E1/ETH) Coms Controller diagnostics port.• Open ECS(E1/ETH) ECT

• Insert “User name” and “Password”• Select “Serial Communication and click on “Login”

12

3

4

9 | SAM Training

ECS(E1/ETH) CONTROLLER – SET UP

ECS(E1/ETH) Set Up:1. Click on “Find” to connect to unit• Check that the units has the latest Firmware

version being “4.0.1.8”• If Not on latest version, upgrade to latest

version1. Click on “Down Load”2. Capture the IP address as indicated 3. Click on “Set” 4. Click on “Site Inventory”

1

2

3

4

1

10 | SAM Training

ECS(E1/ETH) COMS CONTROLLER – SET UP

ECS(E1/ETH) Set Up:1. Capture ECS(E1/ETH) Coms Port setup as

per screen print 2. Click on “Set” on the “Network” tab once

done.

11 |

TESTING COMMUNICATION TO THE SAM OR ACCESS CONTROL UNITVIA THE ECS(E1/ETH) COMMUNICATION CONTROLLER

12 | SAM Training

LAPTOP – SET UP

Laptop Set Up:Your Laptop IP address needs to be changed so that it is within range of the coms controller1. Connect LAN cable between the Coms

controller and the Laptop2. Open Network settings3. Click on “Local area Connection”4. Click on “Properties”5. Select “Internet protocol Version

4(TCP/IP).6. Click on “Properties”7. Click on “Use the following IP Address” 8. Capture the IP address – IP address will be

the same as the Coms controller except the last digit must differ

9. The Subnet mask and gateway IP must be the same as the coms controller

10. Click on “OK”

13 |

SAM2 COMMUNICATION TESTVIA THE ECS(E1/ETH) COMMUNICATION CONTROLLER

14 | SAM Training

SAM2 – COMMUNICATION TEST VIA ECS2 COMMUNICATION CONTROLLER – “RS485”

RS485 Communication Test;• Connect a LAN cable between the Lap Top and the

ECS(E1/Eth) LAN port• Open SAM2 ECT

• Select “TCP” and insert the IP address of the ECS(E1/Eth) and Port 301 and double click on “Password”

15 | SAM Training

SAM2 – COMMUNICATION TEST VIA ECS2 COMMUNICATION CONTROLLER – “RS485”

RS485 Communication Test; Cont;• Active communication will be shown on the

bottom left as indicated with the RED circle until it says “received”

16 |

SAM1.5 COMMUNICATION TESTVIA THE ECS2 COMMUNICATION CONTROLLER

17 | SAM Training

SAM1.5 – COMMUNICATION TEST VIA ECS2 COMMUNICATION CONTROLLER – “RS485”

RS485 Communication Test;• Connect a LAN cable between the Lap Top and the

ECS(E1/Eth) LAN port• Open SAM2 ECT

• Select “TCP” and insert the IP address of the ECS(E1/Eth) and Port 301 and double click on “Password”

18 | SAM Training

SAM1.5 – COMMUNICATION TEST VIA ECS2 COMMUNICATION CONTROLLER – “RS485”

RS485 Communication Test; Cont;• Active communication will be shown on the

bottom left as indicated with the RED circle until it says “received”

19 |

ACCESS CONTROL COMMUNICATION TESTVIA THE ECS2 COMMUNICATION CONTROLLER

20 | SAM Training

ACCESS CONTROL – COMMUNICATION TEST VIA ECS2 COMMUNICATION CONTROLLER – “RS485”

RS485 Communication Test; Cont;1. Click on “TCP” and insert IP address of

the ECS(E1/Eth).2. Click on “Connect”3. Click on “Logon”4. Click on “Open Door”5. Click on “Get Version”6. Click on “Get Time”7. Click on “Log off”8. Click on “Exit”

• Responses should be received as indicated in the Red circle

1

2 3

4

5

6

6 7

21 |

CLICK TO EDIT MASTER TITLE STYLE

THANK YOU