Date post: | 02-Jan-2016 |
Category: |
Documents |
Upload: | andreeas10 |
View: | 14 times |
Download: | 7 times |
1
Introduction
Internal combustion engine design for the mass market is driven by two
global issues: cost of fuel and emission controls
2
Most motor vehicle fuels are derived from crude oil which is not a renewable
commodity
The cost of crude oil is driven by market supply and demand
Crude oil reserves limited to a few countries in the world, mainly the
Middle east, Canada, Russia, Venezuela, and U.S.
Current oil reserves of roughly 1.25 trillion barrels are estimated to be
depleted by 2050-2090 based on usage of 100 million barrels
The largest oil reserves are located in unstable countries where conflicts
often affect oil production
Demand is expected to increase as developing countries such as China
(pop. 1.3 billion) and India (pop. 1.1 billion) prosper
Price of Crude Oil
3
4
Environmental Concerns
Burning of fossil fuels in internal combustion engines produce harmful
emissions that affect the health of living creatures on earth
In the developed countries the government regulates the level of harmful
emissions from vehicles (UHC, NOx, SOx, CO, C)
Even the emission of chemically carbon dioxide (stuff we exhale) from
vehicles contributes to global warming will shortly be regulated
There is a cost associated with meeting the vehicular emission standards
which are becoming more and more stringent with time
5
Internal Combustion Engine
The internal combustion (IC) engine is a heat engine that converts
chemical energy stored in a fuel into mechanical energy, usually made
available on a rotating output shaft.
History of IC engines:
1700s - Steam engines (external combustion engines)
1860 - Lenoir engine (h = 5%)
1867 - Otto-Langen engine (h = 11%, 90 RPM max.)
1876 - Otto four-stroke “spark ignition” engine (h = 14%, 160 RPM max.)
1880s - “Modern” two-stroke engine
1892 - Diesel four-stroke “compression ignition” engine
1957 - Wenkel “rotary” engine
6
Atmospheric Engine
Process 1-2: Fuel air mixture introduced into cylinder at
atmospheric pressure - valve open (VO)
Process 2-3: Constant pressure combustion (cylinder open
to atmosphere)
Process 3-4: Constant volume cooling (produces vacuum)
Process 4-5: Isentropic compression (atmosphere pushes piston)
Process 5-1: Exhaust process
31
2Po
4
5
Pressure
Volume
VALVEPatm
(VO)(VC)
(VO)
FLYWHEEL
7
Historical IC Engines
FLYWHEEL
8
Two-stroke Lenoir Engine
Process 1-2: Fuel air mixture introduced into cylinder at
atmospheric pressure
Process 2-3: At half-stroke inlet valve closed and combustion
initiated constant volume due to heavy piston
producing high pressure products
Process 3-4: Products expand producing work
Process 4-5: At the end of the first stroke exhaust valve opens and
blowdown occurs
Process 5-1: Exhaust stroke
3
1(VO) 2 (VC)Po
4(VO)
5
P
V
9
Two-stroke Otto-Langen Engine
Process 1-2: Fuel air mixture introduced into cylinder at
atmospheric pressure
Process 2-3: Early in the stroke inlet valve closed and combustion
initiated constant volume due to heavy piston
producing high pressure products
Process 3-4: Products expand accelerating a free piston
momentum generates a vacuum in the tube
Process 4-5: Atmospheric pressure pushes piston back, piston
rack engaged through clutch to output shaft
Process 5-1: Valve opens gas exhausted
Disengaged
output shaft
Engaged
output shaft
10
Crank shaft
90o
180o
BC
TC
0o
270o
q
Modern Engine Components
Spark plug for SI engine
Fuel injector for CI engine
Top
Center
(TC)
Bottom
Center
(BC)
Valves
Clearance
volume
Cylinder
wall
Piston
Stroke
CA
rev
rev
sCA
360
1
speedcrank
angles(CA)crank time
Pressure and
oil rings
Connecting
rod
Cylinder head
11
Four-stroke Spark Ignition (SI) Engine
Stroke 1: Fuel-air mixture introduced into cylinder through intake
valve
Stroke 2: Fuel-air mixture compressed
Stroke 3: Combustion (roughly constant volume) occurs and
product gases expand doing work
Stroke 4: Product gases pushed out of the cylinder through the
exhaust valve
Compression
StrokePower
Stroke
Exhaust
Stroke
A
I
R
Combustion
Products
Ignition
Intake
Stroke
FUEL
Fuel/Air
Mixture
12
Pressure-Volume Graph 4-stroke SI engine
One power stroke for every two crank shaft revolutions
1 atm
Spark
TC
Cylinder volume
BC
Cylinder
Pressure
Exhaust valve
opens
Intake valve
closes
Exhaust
valve
closes
Intake
valve
opens
13
IVO - intake valve opens, IVC – intake valve closes
EVO – exhaust valve opens, EVC – exhaust valve opens
Four-stroke engine valve timing
Intake Exhaust
TC
BC
IVO EVC IVC EVO IVO
Valve overlap
14
IVO - intake valve opens, IVC – intake valve closes
EVO – exhaust valve opens, EVC – exhaust valve opens
Cylinder pressure for motored four-stroke engine
10
Pressure (bar)
100
Intake Exhaust
TC
BC
15
IVO - intake valve opens, IVC – intake valve closes
EVO – exhaust valve opens, EVC – exhaust valve opens
Xb – burned gas mole fraction
Four-Stroke SI Engine
10
Pressure (bar)
100
Intake Exhaust
16
Compression
Stroke
Power
StrokeExhaust
Stroke
A
I
R
Combustion
Products
Intake
Stroke
Air
Fuel Injector
Four stroke Compression Ignition (CI) Engine
Stroke 1: Air is introduced into cylinder through intake valve
Stroke 2: Air is compressed
Stroke 3: Combustion (roughly constant pressure) occurs and
product gases expand doing work
Stroke 4: Product gases pushed out of the cylinder through the
exhaust valve
17
SOI – start of injection
EOI – end of injection
SOC – start of combustion
EOC – end of combustion
Four-Stroke CI Engine
Fuel mass
flow rate
Fuel mass
burn rate
Cylinder
volume
Cylinder
pressure
18
Camshaft
Intake valve
Rocker arm
Piston
Connecting rod
Crankshaft
Oil pump
Exhaust valve
Crank sprocket Oil pickup
Timing belt
Cam sprocket
Air cleaner
Timing belt
tensor
Engine Anatomy
19
Ford’s inline 4-cylinder Duratec 2.3 Liter (SAE Automotive Engineering, Oct. 2005)
20
Poppet Valve Actuation with Overhead Camshaft
Camshaft
Spring
Air manifold
Stem
Guide
Valve head
Valve seat
Piston
Spark
plug
21
Modern Two-Stroke Spark Ignition Engine
Stroke 1: Fuel-air mixture is introduced into the cylinder and
is then compressed
*combustion initiated at the end of the first stroke
Stroke 2: Combustion products expand doing work and then
exhausted from the cylinder
* Power delivered to the crankshaft every revolution
22
Traditional two-stroke SI engine
Intake (“Scavenging”)
Compression Ignition
ExhaustExpansion
Fuel-air-oil
mixture
Fuel-air-oil
mixture
Crank
shaft
Reed
valve
Exhaust
port*
Transfer
port*
* No valves and
thus no camshaft
Spark
plug
23
EPO – exhaust port open
EPC – exhaust port closed
IPO – intake port open
IPC – intake port closed
Two-Stroke CI Engine
scavenging
Ai
Ae
Intake area (Ai)
Exhaust area (Ae)
PiPe
Exhaust Press (Pe)
Intake Press (Pi)
Cylinder Press (P)
110 CA
V
Vc
Cylinder Vol. (V)
P
P
24
Cross Loop Uniflow
Scavenging in Two-Stroke Engine
25
Advantages of the two stroke engine:
• Power to weight ratio is higher than the four stroke engine since there
is one power stroke per crank shaft revolution.
• No valves or camshaft, just ports
Most often used for low cost, small engine applications such as lawn
mowers, marine outboard engines, motorcycles….
Disadvantages of the two-stroke engine:
• Incomplete scavenging – limits power
• Fuel-air “short circuiting” – low fuel efficiency, high HC emission
• Burns oil mixed in with the fuel – high HC emission
26
(2005)
27
Single Cylinder Engine
Single-cylinder engine gives one power stroke per crank revolution
(360 CA) for 2 stroke, or every two revolutions for 4 stroke.
The torque pulses on the crank shaft are widely spaced, and engine
vibration and smoothness are significant problems.
Single cylinder engine used in applications where engine weight
and size is important (garden equipment)
180 CA0 CA
(TC)
720 CA
(TC)
540 CA360 CA
(TC)
180 CA
4-stroke
2-stroke
28
Multi-cylinder Engines
Multi-cylinder engines spread out the displacement volume amongst
multiple smaller cylinders. Increased frequency of power strokes
produces smoother torque characteristics.
Most common cylinder arrangements are in-line 4, 6 and V-6,-8:
Engine balance (inertia forces associated with accelerating and
decelerating piston) better for in-line versus V configuration.
29
V-6 Engine
Air intake
manifold
Inlet
runner
30
SI Engine Power Regulation
• For proper combustion the ratio of the mass of air to the mass of fuel
in the cylinder must be roughly 15.
• An IC engine is basically an air engine, the more air that enters the
cylinder, the more fuel can be burned, the more energy (power) output.
• Vary throttle position - Maximum intake pressure (and power) achieved
at wide-open-throttle (WOT) and minimum at idle
WOT
Idle
Patm Pint < Patm
Intake
manifold
Fuel
Air
Air
filter
Throttle
31
Power Regulation Methods
Basic methods:
1) Manifold pressure
2) Air mass flow rate
3) Throttle position
Engine Control Unit (ECU) activates the fuel injector solenoid for a
duration corresponding to measurement of air flow or pressure
PatmPint < Patm
Intake
manifold
Fuel
Air mass
flow meter
Pressure
transducer
Throttle
position
sensor
32
• In spark ignition engines the air and fuel are usually mixed prior to entry
into the cylinder.
• Initially a purely mechanical device known as a carburetor was used to
mix the fuel and the air
• Most modern cars use electronic fuel-injection systems:
- 1980s single injector used to spray fuel continuously into the air manifold
- 1990s one injector per cylinder used to spray fuel intermittently into the
intake port
Fuel-Air Mixing
33
Basic Carburetor
Venturi
Throttle
Air Flow
Mixture to manifold
Fuel
close for start-up to inc DP
34
SI Engine Fuel Injection System
Throttle
Fuel tank
Air intake
manifold
Injector fuel pressure varied relative to manifold pressure (engine load).
During start-up additional fuel is added through a second injector.
200 KPa
Pref
35
Port fuel injector
Intake port
Fuel line
Battery and
ECU
36
Diesel Fuel Injection System
With diesel engines fuel is sprayed directly into the cylinders
power is varied by metering the amount of fuel added (no throttle)
Diesel fuel injection systems operate at high-pressure, > 100 MPa
• fuel pressure must be greater than the compression pressure
• need high fuel jet speed to atomize droplets small enough for rapid
evaporation
Fuel system includes fuel pump, lines and nozzles
In traditional systems the pump is used to raise the pressure of the
fuel, as well as meter and distribute the fuel to each cylinder.
The pressure is raised by individual barrel-plunger for each nozzle
(in-line type) or a single barrel plunger (distributor type).
Nozzle is a passive device that actuates (spindle rises) when the fuel
pressure increases. The spindle is normally held closed by a spring.
37
Electronic Unit injector
Pump and nozzle incorporated into single unit
Low pressure (500 kPa) fuel pump delivers filtered
fuel to injector port
Plunger up stroke - pump element fills with fuel
Plunger down stroke:
- solenoid de-energized fuel spills into return duct
- solenoid is energized fuel is compressed (2000 bar)
injector needle valve opens
- solenoid de-energized fuel valve opens pressure drops
needle valve opens
Delphi E-1
38Fuel injector pump
In-line Diesel Fuel Injection System
Fuel injector nozzle
Fuel tank
NozzleFilter
cam
In-line fuel injection pump (compresses and meters)
39
• Latest Diesels use high pressure (2000 bar) common rail with solenoid
or piezoelectric actuated injectors.
• Multiple injections per stroke possible.
Common Rail Diesel Fuel Injection System
Bosch diesel pump (2000 bar)
and piezoelectric injector
40
GDI engine combines the best features of SI and CI engines:
• Fuel is injected directly into the cylinder during the intake stroke or the
compression stroke (high pressure injector)
•`Operate at optimum compression ratio (12-15) for efficiency by
injecting fuel directly into engine during compression (avoiding knock
associated with SI engines with premixed charge)
• Control engine power by fuel added (no throttle no pumping work)
• During intake stroke fuel cools the cylinder wall allowing more air into
the cylinder due to higher density
Gasoline Direct Injection (GDI) Engine
41
Two types of GDI Engines
Wall-guided
Spray-guided
Hollow-cone
spray pattern
Injector
Flat piston
face
Trough-shaped
piston face
Injector
Injected fuel swirls
around when it hits
the piston face
42
BMW spray-guided GDIWall-guided GDI
43
Dual Port and Direct Fuel Injection
2006 Lexus 3.5 L V6 engine (SAE Automotive
Engineering Dec 2005)
Stoichiometric mixture created by
combination of fuel port and direct
fuel injection
• Low rpm use 30-40% DI to produce
extra in-cylinder turbulence
• High RPM and load use 100% DI
to reduce air temp (increase density)
44
GDI stratified-charge mode
• Create easily ignitable fuel-air mixture at the spark plug and a leaner
fuel-air mixture in the rest of the cylinder.
• Lean burn results in lower emissions and higher energy efficiency
Example:
Mitsubishi GDI engine achieves complete combustion with an air-fuel
ratio of 40:1 compared to 15:1 for conventional engines
This results in a 20% improvement in overall fuel efficiency and CO2
production (greenhouse gas), and reduces NOx emissions
(responsible for ozone production - smog) by 95% with special
catalyst
45
Stratified Charge Engine
During intake stroke air enters the cylinder
Near the end of the compression stroke fuel is injected and directed
by the piston head bowl towards the spark plug
The mixture at the spark plug is “rich” in fuel thus easy to ignite but
the amount of fuel injected results in an overall “lean” fuel-air mixture
Lowers heat transfer to the walls but increases thermal cyclic load on
the spark plug, and standard catalytic converter doesn’t work
46
Mitsubishi Two-Stage Ignition GDI Engine
47
Rich
intake
Lean
intake
Two-Chamber Torch or Jet Ignition Engine
48
• Premixed lean fuel-air mixture is created in the cylinder like a SI engine
but ignition occurs spontaneously at the end of compression like a
Diesel engine
• Get the efficiency of a Diesel with low temperature, flameless release of
energy throughout the cylinder no need for expensive low-NOx emission
after-treatment
• Can use multiple fuel types: gasoline, diesel, ethanol, etc.
• Fuel-air mixture is preheated by either heating the air or mixing with
combustion products from previous cycle
Challenge: control the ignition timing for different load and engine speeds,
need spark ignition for cold start up
Homogeneous Charge Compression Ignition (HCCI)
49
• GM demonstrated the first HCCI engine in a 2007 Saturn Aura
• Vehicle gets 15% better fuel economy compared to port injected engine
while meeting current emission standards
• Engine uses direct injection, variable valve timing and lift
Homogeneous Charge Compression Ignition (HCCI)
50
Plug-in Electric Vehicles
Electric motor driven from battery pack that is recharged via
electric outlet
GM re-entry into electric vehicle is the Chevy Volt plug-in out in
2010, a small IC engine powers a generator that runs motor once
the batteries are depleted after 50 mile range ($40k, less subsidies)
All the leased vehicles were crushed at the end of the 3 year
lease, chronicled in the movie Who Killed the Electric Car?
In 1996, 800 GM EV-1 were made available for lease in California
Others due in 2011 are Toyota Prius,
Nissan Leaf, Tesla Roadster
Used for US government vehicles
51
Electric Motor Powered Vehicles
Biggest asset: no emissions, low end torque, no gears
Problems:
- vehicle range dictated by battery storage
- batteries need to be recharged which takes several hours
- cost of batteries
- weight of batteries
Alternative is gas-electric hybrid:
- Toyota Prius (1997), Honda Insight (2000)
- Over 100,000 units sold in 2005
52
Gasoline-Electric Hybrid Vehicles
• Parallel hybrid uses a combination of a small IC engine (1-1.5 L) and
an electric motor driven off batteries, in a series hybrid IC engine only
charges the batteries (GM Volt).
• Electric motor is used exclusively during cruise and idle when the
vehicle is stationary.
• IC engine kicks in when additional power is needed during
acceleration and up hills.
• Vehicles use regenerative braking - during braking the electric motor
acts like a generator recharging the batteries, so never need to recharge.
• Disadvantage: premium price (Government subsidy ) and cost to
replace batteries after 8 year 160,000 km warranty period is expensive
53
54
Supercharger and Turbocharger
These devices are used to increase the power of an IC engine by raising
the intake pressure and thus allowing more fuel to be burned per cycle.
Allows the use of a 4 cyl instead of 6 cyl engines cost effective
Superchargers are compressors that are mechanically driven by the engine
crankshaft and thus represents a parasitic load.
Compressor
Patm
Pint > Patm
Win
55
Positive Displacement Compressors
Positive displacement compressors: piston, Roots, and screw
Most common is the Roots compressor – pushes air forward without
pressurizing it internally.
Pressurization occurs in the manifold when the air flow rate supplied
is larger than that ingested by the cylinders.
Produces constant flow rate independent of boost pressure (P2)
P1 P2
56
Performance of Positive Displacement Compressors
s/co = rotor tip Mach#
~ pump speed
hc = compressor efficiency: actual work/isentropic work
Extra energy goes to heat up air leading to a reduction in density
hc
Screw
Roots
57
Dynamic Compressors
Dynamic compressor has a rotating element that adds tangential
velocity to the flow which is converted to pressure in a diffuser.
Most common is the radial (or centrifugal) type
Produces a constant boost pressure independent of the mass flow rate
58
Mass flow rate (Pounds of air per minute)
To the left of surge line the flow is
unstable (boundary layer separation
and flow reversal)
To the right of 65% line the compressor
becomes very inefficient:
a) air is heated excessively
b) takes excess power from the crank
shaft
59
Turbochargers couple a compressor with a turbine driven by the exhaust
gas. The compressor pressure is proportional to the engine speed
Compressor also raises the gas temperature, so after-coolers are used
after the compressor to drop the temperature and thus increase the air
density.
60
The peak pressure in the exhaust system is only slightly greater than
atmospheric – small DP across turbine
In order to produce enough power to run compressor the turbine speed
must be very fast (100k-200k rev/min) – long term reliability an issue
Takes time for turbine to spool up to speed, so when the throttle is opened
suddenly there is a delay in achieving peak power - turbo lag
INTAKE
AIR
EXHAUST
FLOW
61
Waste gate valve used to bypass exhaust gas flow from the turbine
It is used as a full-load boost limiter and in new engines used to control
the boost level by controlling the amount of bypass using proportional
control to improve drivability
Turbine Compressor
WASTE GATE
Proportional
valve
Engine
Exhaust
Patm
AIR
Patm
62
Turbo Lag Reduction: Twin Turbo
Two turbochargers:
• Smaller turbo for low rpm low load and a larger one for high load
• Smaller turbo gets up to speed faster so reduction in turbo lag
Supercharger/turbo:
• Supercharger used at low speed to eliminate turbo lag
• At higher rpm turbo charger used exclusively to eliminate parasitic load
2006 Volkswagen Golf GT 1.4 L GDI uses twin turbo:
0-2400 rpm roots blower
>3500 rpm turbo charger
63
BMW 2.0L I4 turbo diesel surpasses 100 hp/L (75 kW/L)
642006 Porche 911 Variable Turbine Geometry uses temperature-resistant materials
Turbo Lag Reduction: Variable Geometry Turbo (VGT)
Variable guide vanes direct the flow of exhaust gas from the engine in
exactly the direction required on to the turbine wheel of the turbocharger.
Good response and high torque at low engine speeds as well as superior
output and high performance at high engine speeds
VGT used on diesel engines with exhaust temps (700-800 C) not
normally used in SI engine due to high exhaust temp (950 C)
Guide vane
65
Low rpm:
Vanes are partially closed accelerating the exhaust
gas flow. The exhaust flow hits the turbine blades at
right angle. Both make the turbine spin faster
High rpm:
The vanes are fully opened to take advantage of the
high exhaust flow. This also releases the exhaust
pressure in the turbocharger, saving the need for
waste gate.
66
Variable Geometry Turbo
Holset VGT