1 Leather hand Gloves 14” Long Materials _Aramid ,Leather Type :-Consumable (Thermal and burn resistance)
2 Cotton hand Gloves 8” Long Materials –Cotton Type –Consumable
3 Apron Materials-Leather(with asbestos sheet) Four Point Fitting
Types-Consumable
4 Stainless Steel Wire brush 5x3 Rows Bristles mount on wooden base
Type- Consumable
5 Hand Sleeve 16”
Materials-Leather Two /Three point fitting Type-Consumable
6 Safety Boot PU/Leather Make with steel toe cap and composite mid sole
Type-Consumable
7 Leg Guard Materials-Leather Two /Three point fitting
Type-Consumable
8 Rubber Hose Clips ½”
Materials Stainless Steel ,Screw Thread Tight Types -Consumable
9 Rubber Hose for Oxygen dia 8 mm length 10 meter Materials-compound synthetics Rubber, Color-Blue, Flexible
Type-Consumable
10 Rubber Hose for Acetylene dia 8 mm length 10 meter Materials-compound synthetics Rubber, Color-Blue, Flexible
Type-Consumable
11 Arc Welding Cable Multi Cored Copper 400/600 Amp. Temp +/- 100 C
Type-Consumable
12 Welding Glass DIN 11A/14A Type-Consumable
13 Plain Glass for cover welding glass 108x82x3 mm Type-Consumable
14 Gas Welding Goggles with color glass 3or4 DIN sealed fitting with head belt
Type-Consumable
15 Safety Goggles Plain Glass sealed fitting with head belt
Type-Consumable
16 Spark Lighter 6”/8” Safe ignition
Type-Consumable
17 AG4 Grinding wheel dia 4” ISI Make
1 Welding Helmet Materials –Fiber Screen lock system by bolting Head fitting flexible
2 Hand Shield Materials –Fiber Screen lock system by bolting , Handle Attachment by bolt
3 Chipping Hammer with Metal Handle Hammer-Forged Steel ,Handle Standard Mild Steel (knurled) or Spring Type
Weight 250 gram without Handle 400 Gram apparox with handle
4 Chiesel Cold Flat 150x20 mm
Materials- High Carbon Steel
5 Center Punch 150 mm Materials- High Carbon Steel
6 Divider 200 mm Materials-SS
Spring type
7 Stainless Steel Rule 300 mm Inches and mm reading least count 0.5 mm
8 Scriber 150 mm
Materials-High Carbon Steel ,Double point ,Center Knurled
9 Flat Tong 350 mm Long Also Made in Fitter/Molder/Welder Trade
10 Hacksaw Frame fixed 300 mm Materials High Carbon Steel , Heavy wing nut and extension rod
With plastic handle
11 File Half Round Bastered 300mm
With wooden/ Plastic Handle
12 File Flat Bastered 300mm With wooden/ Plastic Handle
13 Hammer Ball Peen 1 kg
Handle wooden
14 Tip Cleaner size 5-45 no. by 5 (Nozzle size) Aluminum make in a steel case
15 Try Square 150 mm
SS Made inches and mm reading
16 Spindle key for oxygen and acetylene cylinder
Double ended opening
17 Screw Driver 300 mm and 250 mm long Tip 10 mm and Tip 6 mm
18 Number Punch 6 mm Length 100 mm
Forged Steel
19 Letter Punch 6 mm Length 100 mm Forged Steel
20 Magnifying Glass Dia 100 mm
Glass fitted in Steel frame with handle
21 Universal weld Measuring gauge SS make , reading in mm
22 Earth Clamp 600 Amp Spring Tight/Screw Tight
Materials –Copper Alloy
23 Spanner Double Ended 6 to 32 mm by one mm
24 C-Clamp 10 cm and 15 cm
High Carbon steel Make, SS spindle
25 Sledge Hammer Double Face 4 kg
26 SS Tape 5 meter
Flexible in a case inches and mm reading
27
Electrode Holder 600 amp Materials Copper Alloy , Spring tight , Fiber Insulation Double Cross Cut Jaw , Cable attachment throw copper strip and bolt
28 High Pressure welding Torch With 5 Nozzle ,Nozzle size 3-15 ,Heavy duty with flash back arrester fitted Materials –Copper Alloy
29 Oxygen Gas Pressure Regulator
Double Stage , with flash back arrester fitted
30 Acetylene Gas Pressure Regulator
Double Stage , with flash back arrester fitted
31 CO2 Pressure Regulator Single Stage , Double gauge ,with flow meter attachment
32 Argon Pressure Regulator Single Stage , Double gauge ,with flow meter attachment
33 Metal Rack 182x152x45 cm Capacity 500-600 kg, three /four block
34 First Aid Box Containing Burnol , Stitch, and first aid medicine
35 Steel Locker with 8 pigeon hole Body made by 16/18 gauge sheet with locking system
36 Steel Almirah Standard size Body made by 16/18 gauge sheet with locking system
37 Black Board
38 Flash Back Arrester (Torch Mounted)
39 Flash Back Arrester (Cylinder Mounted)
40 Welding Transformer with all Accessories ( Welding Cable ,Electrode Holder ,Earth Clamp and Hand Screen) 400 Amp ,Open Circuit Voltage 60-100 V, 60% duty Cycle, Three Phase ,Air Cool, with current adjustment lever/regulator ,
Copper coiling with ammeter and voltmeter
41 Welding Transformer Invertor based with all Accessories ( Welding Cable ,Electrode Holder ,Earth Clamp and Hand Screen) 300 Amp ,Open Circuit Voltage 60-100 V, 60% duty Cycle, Single/double Phase ,Air Cool,
with current adjustment lever/regulator , Copper coiling with ammeter and voltmeter
42 DC Arc Welding rectifier set with all accessories ,
400 amp, 60-100 volt OCV, 60% duty cycle, three phase air cool, polarity switch, ammeter and voltmeter on working, Regulator controlled , Low-medium-high current Adjustment
43 GMAW Machine 400 Amp , Air Cooled/Water cooled Torch ,
Gas Pre heater , Gas hose and standard accessories ( Complete set in working) with extra nozzle and tip (0.8/1.2 mm) air cool ,three phase , voltmeter and ammeter on working ,
fine and course adjustment switch
44 AC/DC GTAW machine with water cooled torch , 300 amp , argon regulator ,
gas hose , water circulating system, all standard accessories , with two ceramic nozzle, with pulsed system .
45 Air plasma cutting equipment cutting capacity 25 mm, inverter based , air pressure safety switch, 2/4 track operation , Air Pressure meter , 6 meter cable hose assembly , thermal over load ,low air pressure indicator , three phase, 15 KVA ,6-8 kg/cm2 pressure , cutting current 100 amp with all standard accessories ( Alumina Cup (5 nos.) , Spring space (5 nos) ,
Gas diffuser -5 nos. , Electrode – 5 nos. ,Nozzle- 5+5 nos.
46 Air Compressor suitable for air plasma cutting, Three phase motor , two stage reciprocating pump with air filter , safety valve ,on/off push switch connected with over pressure ,
10-15 bar , belt safety guard.
47 Auto darkening welding helmet , timing 1/10 second , Battery/solar power operated , dark shade control switch ,
wearing adjustment
48 Spot welding machine 15 KVA ,Air/water cooled, pedal operated with ammeter and voltmeter , single/double phase, throat distance 175-300 mm , rocker arm dia 40-60mm ,
electrode length 200 mm, 10 kilo amp current supply
49 Portable gas cutting machine, straight and circular cutting , electric motor operated with speed control switch , five feet line for straight cutting, ½” and ¼” fitting adjustment with flash back arrester, torch angular adjustment
50 Pedestal grinder course and medium grinding wheel 300 mm, three phase with tool rest system ,
speed controller ,copper winding , double bearing ,made by forged cast iron, wheel cover
51 Bench grinder , fine grain size silicon wheel 150 mm, with tool rest system , wheel cover,
single phase , made by forged cast iron
52 AG 4 Grinder , single phase , 3 meter cored wire , with push and lock switch with wheel guard and key
53 Suitable gas welding table with fire bricks, size 4’x2’x2.6’
54 Suitable arc welding table size 4’x2’x2.6’ , with arc cutting adjustment
55 Trolley for cylinder with chain ( Fix the cylinder on Trolley)
56
Hand shearing machine , cap 0-6 mm, geared system with cutting base
57 Power saw machine 18 “ , hydraulic controlled with water cooling system on a heavy base with water storage tank ,motorized with copper winding ,
three phase , on/off push switch
58 Portable drilling Machine , single phase , 6 mtr cored wire 2200-2800 RPM , push and lock switch
59 Oven 10 Kg capacity , 350 degree , single phase , with temperature display and adjustment , auto cut, on a stand
60 Workbench 8x4x2.6 feet with four vices , heavy base with 2”/3” wood
61 Oxy-acetylene cutting blow pipe heavy duty with nozzle
62 Oxygen cylinder MFG date after 2005
63 Acetylene cylinder MFG date after 2010
64 Argon cylinder MFG date after 2005
65 Anvil 12” Square hammering base with stand
66 Swedge Block size 14x14x5 inches
67 Die Penetrate Testing Kit with 115PR, 115 D, 115 P
68 Magnetic particle testing kit, 220 Volt ,10 meter cored wire , with red and gray powder (450 Gram), Adjustable magnetic pillar , with ammeter and voltmeter ,
leg capacity 0-12”
69 Fire extinguisher CO2 and Foam
70 Fire bucket with stand , 2 bucket contain sand and two bucket contain water
71 Portable abrasive cut off machine , single phase ,2200-3200 RPM , 1HP motor , angular cutting adjustment with safety cover
72 Suitable gas cutting table with cutting adjustment
73 Welding simulator (Advanced welding CD/DVD)
1 Instructor chair made with 18 gauge pipe
2 Student chair with writing pad 18 gauge pipe and 1 “ board
3 White board 1200x900 mm
4 Laptop latest version with MS office license package with license antivirus for 3 years
5 LCD Projector resolution 1021x768 , Throw distance 3 meter , Image size 100” , uniformity not less than 90 % , 3X digital zoom, Screen- Wall fitting/ceiling fitting , 8x6 feet, fold in a cover
6 Advance welding video cd/dvd
