- - - - - - - - - - - - - - - - - - - - - - - - ILL-01 MSB JA NUMBER DRAWING NUMBER DRAWING INDEX OF DRAWINGS DRAWING TITLE DRAWING TITLE BEEN PERSONALLY CHECKED BY THE UNDERSIGNED. NOT TO BE CONSTRUED TO MEAN THAT ALL ASPECTS OF THE DESIGN HAVE THE DESIGN APPEARS TO CONFORM TO APPLICABLE CRITERIA. APPROVAL IS DESIGNER/DRAFTER: CHECKED BY: PROJECT TITLE: TOWN: DRAWING TITLE: PROJECT NO. DRAWING NO. SHEET NO. Filename: SHEET NO. REVISION DESCRIPTION DATE REV. DEPARTMENT OF TRANSPORTATION STATE OF CONNECTICUT OF WORK WHICH WILL BE REQUIRED. THE CONDITIONS OF ACTUAL QUANTITIES IN NO WAY WARRANTED TO INDICATE INVESTIGATIONS BY THE STATE AND IS SHEETS IS BASED ON LIMITED QUANTITIES OF WORK, SHOWN ON THESE THE INFORMATION, INCLUDING ESTIMATED 7/15/2015 BLOCK: SIGNATURE/ Plotted Date: C O N N E C T I C U T D E P A R T M E N T O F T R A N S P O R T A T I O N 10 - ELECTRICAL- ILLUMINATION ON ROUTE 4 (FARMINGTON AVE) FROM GARDEN ST. TO MOUNTAIN SPRING RD. FARMINGTON 51-260 SAFETY & TRAFFIC OPERATIONAL IMPROVEMENTS ELECTRICAL INDEX OF DRAWINGS ILLUMINATION PLAN ILL-02 ELECTRICAL INDEX OF DRAWINGS ILL-01 ELECTRICAL DETAILS 1 ILL-03 ELECTRICAL DETAILS 2 ILL-04 ELECTRICAL DETAILS 3 ILL-05 10.01
Transcript
- -
-
-
-
- -
- - -
- - - -
- - -
- - -
- - - -
ILL-01
MSB
JA
NUMBER
DRAWING
NUMBER
DRAWING
INDEX OF DRAWINGS
DRAWING TITLE DRAWING TITLE
BEEN PERSONALLY CHECKED BY THE UNDERSIGNED.
NOT TO BE CONSTRUED TO MEAN THAT ALL ASPECTS OF THE DESIGN HAVE
THE DESIGN APPEARS TO CONFORM TO APPLICABLE CRITERIA. APPROVAL IS
The plans have been checked that the following tasks have been completed correctly: 1. Page Labels 2. Sheet Numbers 3. Watermarked 4. Comments Flattened 5. Digital Signature was applied allowing for markups
228.7
0
LA
NDIN
G
220.6
2
IN
VE
RT
WB-67 - Interstate Semi-Trailer
242.8
LANDING
+222.
88'
+223.
67'
+222.
78'
+222.
49'
+223.
89'
+218.3
0'
+219.4
4'
+217.2
9'
+218.1
1'
+221.8
5'
+225.
92'
+223.
16'
+221.3
9'
+224.
32'
700+00
701+
00
1+60
920+00
920+90
911+00
980+
00
961+
00
101+
00
102+00
103+00
104+
00
105+
00
106+
00
107+
00
108+
00
109+00
110+72
900+00
901+00
902+00
903+00
904+00
904+60
904+60
500+
00
501+00502+00502+82
962+
00
960+
00
970+
00
960+00
961+
00
961+
56
961+
56
110+00
930+
00
931+
00
932+
00
933+00933+10
933+10
940+
00
941+
00
941+
60
941+
60
941+59.
95
PI
950+00
951+00
951+50
951+50
41+
00
42+
00
43+
00
44+
00
45+
00
46+00
47+00
48+00
49+00
800+00
801+
00
DESIGNER/DRAFTER:
CHECKED BY:
PROJECT TITLE: TOWN:
DRAWING TITLE:
PROJECT NO.
DRAWING NO.
SHEET NO.
Filename:SHEET NO.REVISION DESCRIPTIONDATEREV.
DEPARTMENT OF TRANSPORTATION
STATE OF CONNECTICUT
SCALE 1"=40'
40 800
SCALE IN FEETOF WORK WHICH WILL BE REQUIRED.
THE CONDITIONS OF ACTUAL QUANTITIES
IN NO WAY WARRANTED TO INDICATE
INVESTIGATIONS BY THE STATE AND IS
SHEETS IS BASED ON LIMITED
QUANTITIES OF WORK, SHOWN ON THESE
THE INFORMATION, INCLUDING ESTIMATED
7/15/2015
BLOCK:
SIGNATURE/
DATE: APPROVED BY:
OFFICE OF ENGINEERING
...\HW_MSH_0051-0260_ILL-02.dgnPlotted Date:
CONNECTICU
T
DE
PA
RT
ME
NT
O F TRANS
PO
RT
ATI
ON
SAFETY & TRAFFIC OPERATIONAL IMPROVEMENTS
ON ROUTE 4 (FARMINGTON AVE) FROM
GARDEN ST. TO MOUNTAIN SPRING RD.
ILL-02
51-260
#2018
SNET
LOCATION WITH TRAFFIC SIGNAL SPAN POLE
LOCATE WITHIN TOWN R.O.W. COORDINATE
SERVICE ENTRANCE AND CABINET - TYPE II
COORDINATE GRIDCONNECTICUT
U.G. SERVICE WITH UTILITY COMPANY
COORDINATE 120/240V, SINGLE PHASE
RO
UTE 4
FAR
MIN
GT
ON
AVE.
SPECIFICATIONS, AND WHERE APPLICABLE, UTILIITY COMPANY REGULATIONS.
ALL ELECTRICAL WORK SHALL CONFORM TO THE NATIONAL ELECTRIC CODE, CONNECTICUT STANDARD
INSTALL ONE NUMBER 8 BARE COPPER GROUNDING CONDUCTOR THROUGHOUT ALL LIGHTING CIRCUITS.
1)
2)
3)
4)
5)
6)
7)
ILLUMINATION NOTES
ILLUMINATION LEGEND
AND INSTALLING THE PULL-LINE SHALL BE INCLUDED IN THE COST OF THE CONDUCTORS.
WHERE CONDUCTORS ARE TO BE PULLED INTO NEW CONDUIT, THE COST OF FURNISHING
MSB
JA
ILLUMINATION
PLAN
OF FARMINGTON.
(860-651-2560). PAYMENT FOR THE MONTHLY ENERGY COSTS SHALL BE THE RESPONSIBILITY OF THE TOWN
COORDINATE METERED ELECTRIC SERVICE HOOK-UP: KEVIN O'BRIEN (860-280-2445) OR JOHN SCHERDECHNY
THE CONTRACTOR SHALL CONTACT THE FOLLOWING EVERSOURCE REPRESENTATIVE 30 DAYS IN ADVANCE TO
TAPE ALL UNUSED CONDUCTORS.
10)
SUBMERSIBLE CONNECTORS.
ALL CONDUCTOR SPLICES IN CONCRETE HANDHOLES SHALL BE MADE WITH INSULATED
8)
9)
TO CENTERLINE OF POLE) OR AS INDICATED ON THE PLANS.
LIGHT STANDARD FOUNDATIONS SHALL BE INSTALLED AS FOLLOWS (DISTANCE
11) ALL PVC CONDUIT SHALL BE SCHEDULE 80.
PRECAST POLYMER CONCRETE HANDHOLE
EXISTING LUMINAIRE ON EXISTING UTILITY POLE
HANDHOLES AND CONDUIT.
CONTRACTOR SHALL VERIFY R.O.W. LINE PRIOR TO INSTALLING FOUNDATIONS,12)
CAP CONDUIT 24" BELOW GRADE
FOR FUTURE USE
AND CAP BOTH ENDS
BELOW DRIVEWAY
INSTALL CONDUIT 24"
CIR. #1 & 2
CIR. #1
CIR. #2
CIR. #2
CIR. #2
CIR. #1
CIR. #1
CIR. #1
FOR FUTURE USE
TERMINATE CIR. #1 IN HANDHOLE
LIGHT POLE BASE
TERMINATE CIR. #2 IN
ALL DECORATIVE LUMINAIRES SHALL BE RATED I.E.S. FULL-CUTOFF WITH TYPE 4 LIGHT DISTRIBUTION.
OF R.O.W. BOUNDARY
LOCATE FOUNDATION IN FRONT
- DIRECTLY BEHIND SIDEWALK (SEE DRAWING NO. ILL-04)
AS FOLLOWS: BLACK, WHITE AND GREEN.
SHALL BE COLORED CROSS LINKED POLYETHELENE (XLP). SINGLE PHASE CIRCUIT COLORS SHALL BE
CONDUCTORS SHALL BE COPPER, INSULATION TYPE XHHW AND RATED FOR 600 VOLTS. INSULATION
* Discipline subset includes the General subset and all other discipline subsets. The 02-Revisions does not need a checklist attached. The standard subsets already have a checklist attached to the index sheets.
– For Internal CTDOT Use Only Discipline Subset Submittal Checklist
The following check list shall be checked and attached to each discipline subset *
prior to being digitally signed.
Check Task Section in DPD
Manual
1. Attach this checklist to the discipline subset. Section 3.1
2. Ensure the plans conform to Section 1.4, step 1 of the Digital Project Development Manual.
Section 1.4
3. Complete the following tasks using Bluebeam on
the discipline subset?
a. Apply Page Labels Section 1.6.2
b. Apply Sheet Numbers Section 1.6.2
c. Apply Watermark Section 2.4
d. Flatten Markups Section 2.4
e. Digital Signature Field Section 2.5.1
4. Type name and telephone number below. 5. Upload, if not in Projectwise already, the
discipline subset into the 100_Contract_Plans folder in Projectwise and attribute the document
correctly?
Section 3.2.4
a. Discipline = CT
b. Main Category = CON
c. Sub Category = FDP, DCD, DCD2,
ADP, ACD, DCO where applicable d. Label = subset number and name.
Example of highways subset would be 03-Highways.
The label for a subset shall be the
same for both FDP and DCD submittals.
Addendum submittals shall match FDP submittals with the addition of “_A#”.
Change Order Submittals shall match FDP submittals with the addition of “_C#”. e. Description field is filled in with
a description of the subset. f. The applicable bridge no.(s) or signal
intersection(s) were selected that is/are associated with this subset.
6. Notify Principal Engineer/Engineer of Record so they can apply their Digital Signature
7. Apply the QA/QC stamp after the discipline subset has been digitally signed.
Section 3.1
I have performed and checked that all the tasks above were performed correctly.
Submitted By (Type in Name) Phone Number (Type in Phone Number)
