20
Fusing Machines
Fusing Machines
2
Today’s consumer expects top quality. With the VEIT Kannegiesser EX Series, these demands can be met by a custom designed fusing machine. The EX is suitable for a wide range of applications of fabric and interlining combinations.
1.1. The Control Unit
Control of the fusing parameters is of utmost importance in a fusing machine.
EX Standard Control Standard control functions:• Set/actual temperature• VEIT Power Management Standby mode saves energy
dur ing downtimes Integrated timer to cool belts after use Minimized power peaks during machine warmup• Pressure displayed in bar or N/cm2
• Belt speed displayed in m/minute and seconds
• On/off function• Diagnostic system for heating
elements, compressed air supply and belt tracking
Advantages:• Clear, simple color display with
temperature control to prevent too low or too high temperatures
• Precise setting of temperature control after belt exchange
• Diagnostic system for all important parameters, avoiding fusing problems
• Digital pressure display in bar or N/cm2, avoiding reading errors
1. MultiStar EX 1000/1400 Series – The Modular Solution
3
neuneu
EXT Touch Screen ControlTouch Screen Control offers additional information on current operating conditions and has a programmable memory.
Advantages:• Easy operation• Selection of many languages• Colorcoded error report for
current and resolved errors• Three coded control access
levels, avoiding programming errors
SB Single Belt LoadingThe EX can be equipped with a single loading and fusing belt.
FE Loading StationThe EX can be equipped with a separate loading station, independent of the fusing belt.
1.2. The Loading and Fusing Solution
VEIT Kannegiesser offers integratedsolutions for loading and fusing.
Advantages:• Separate on/off functions for
loading and fusing belts, avoiding errors
• Effortless and smooth transfer from loading to fusing belts thanks to synchronized systems
• Comfortable working conditions for operators at unheated loading station
Touch Screen Control functions:• Set/actual temperature• VEIT Power Management Standby mode saves energy during downtimes Integrated timer to cool belts after use Minimized power peaks during
machine warmup• Pressure displayed in bar or N/cm2
• Belt speed displayed in m/minute and seconds
• On/off function• Programmable memory • USB port for printing, exchanging
and reviewing programs• Diagnostic system for heating
elements, compressed air supply, belt tracking and error reports
4
Top
Bottom
Heat Zone 2/3 – Top/BottomIn this classic arrangement of heat ing elements for dress shirts and sportswear in the EXT 1000/1400, the adhesive resin is melted by the initial upper heating zone and applied to the fabric by the extended lower heating zone.
Heat Zone 3/2 – Bottom/TopExcellent results are achieved in this arrangement of heating elements in the EXT 1000/1400, especially withfabrics and interlinings for sportswear. The fabric is gradually warmed by the initial lower heating zone, allowing creasefree fusing while maintaining fabric structure. Heavier fabrics are also fused successfully with this configuration.
The Heat Zone Configuration – Bottom or TopUnique to VEIT Kannegiesser are the various heat zone configurations available, allowing to meet individual client needs. Whether for dress shirts or sportswear, the choice of heating elements and heat zone configurations plays an important role.
1.3. The Heating System
The proven heating system and heat zone configurations are highlights among the VEIT Kannegiesser innovative developments. The heating system is designedto avoid problems during and after the fusing process. The energy conscious VEIT Power Management consumes only as much energy as is really needed to quickly reach and maintain the set temperature, providing additional power to individual heat zones as needed.
The Heating ElementAluminum profile construction optimizes energy efficient heat transfer.
Advantages:• Uniform surface temperature • Minimal heat loss due to optimal
heat transfer• Rapid temperature change• Precision temperature control
with minimal fluctuations• Specially insulated heating
elements provide specific heat transfer for minimal energy waste
• Fabric structure maintained
5
1.4. The Pressure System
VEIT Kannegiesser is the industry leader in pressure technology, the most underestimated aspect of a fusing machine. Our unique modular pressure system meets individual client needs through customized configurations.
Advantages:• Applicable for a wide variety of
modern fabrics and interlinings.• Pneumatic pressure rollers can
be customcoated with silicone of various degrees of hardness, meeting specific application needs
• Double Pressure System CU is upgradeable at a later dateEX 1000/1400 C S (soft)
Applicable for pressure sensitivefabrics
EX 1000/1400 C M (medium)Applicable for outdoor wearand dress shirts
EX 1000/1400 C H (hard)Applicable for items requiring fusing with a high, specific pressure
Advantages:• Proven performance with
difficulttofuse fabric and interlining combinations
• Universally applicable thanks to two independent pressure systems.
• Double pressure systems can be operated independently or in tandem
• Effective for classical outerwear as well as dress shirts
Double Pressure System EX CU
EX 1000/1400 CU S (soft)Applicable for pressure sensitive fabrics used in sports shirts and men’s and women’s apparel
EX 1000/1400 CFC Applicable for pressure sensitive and heavyweight items which are prone to compress during fusing
EX 1000/1400 CU H (hard)Applicable for items requiring fusing with a high, specific pressure
EX 1000/1400 CU M (medium)Applicable for men’s apparel, goods with hightwist yarns and dress shirts
Advantages:• VEIT Kannegiesser patented
double pressure system CFC specifically designed for
sensitive fabrics• Air filled rollers provide uni
formly soft pressure to ensure gentle fusing
• Double pressure systems can be operated independently or in tandem
Double Pressure System EX CFC – FLEXO
Standard Pressure System EX C
6
1.5. The Modular EX System
Available customized options:
Multi Star EX1000
PressureSystem
StandardPressureSystem
C
Soft Soft Soft
Medium Medium
Hard Hard
DoublePressureSystem
CU
FlexoPressureSystem
CFC
StandardPressure
C
Soft
Med
ium
Hard
DoublePressure
CU
DoublePressureFlexo CFC
Accessories
FE-L
Return Feed System
ET
Heat ZoneConfi guration
Top FirstHeat Zone
Top
Bottom FirstHeat Zone
Bottom
Top
Bottom
Heat Zones Pressure System
Control Panel
StandardControl Panel
EX
Touch ScreenEXT
EXT
EX
Control Panel Accessories
Feeding System
Single Belt forLoading and
FusingSB
SeparateLoading andFusing Belt
FE
Feeding System
Feeding System
FE
Single Belt SB
BasicBA
TableTA
Table TA
Basic BA
Multi Star EX1400
Top
Bottom
PressureSystem
StandardPressureSystem
C
Soft Soft Soft
Medium Medium
Hard Hard
DoublePressureSystem
CU
FlexoPressureSystem
CFC
StandardPressure
C
Soft
Med
ium
Hard
DoublePressure
CU
DoublePressureFlexo CFC
Control Panel
StandardControl Panel
EX
Touch ScreenEXT
EXT
EX
Accessories
FE-L
ET
Heat Zones Pressure SystemControl Panel Accessories
Feeding System
Single Belt forLoading and
FusingSB
SeparateLoading andFusing Belt
FE
Feeding System
Feeding System
FE
Single Belt SB
BasicBA
BasicBA
FE-L
Heat ZoneConfi guration
Top FirstHeat Zone
Top
Bottom FirstHeat Zone
Bottom
7
2. MultiStar DXT 1400L/1600 Series – The HighPerformance Solution
Touch screen control functions:• Set/actual temperature• Pressure displayed in bar or N/cm2
• Belt speed displayed in m/minute and seconds
• On/off function• Program memory• USB ports for printing, exchanging
and reviewing programs• Diagnostic system for heating ele
ments, compressed air supply, belt progression and error reports
The DXT is the ideal solution for clients working with especially heavy or absorbent fabrics or those with large production runs where speed is required.
Advantages:• Easy of operation• Selection of many languages• Color coded error report for
current and resolved errors• Three coded control access
levels, avoiding programming errors
2.1. The Control Unit
Touch Screen Control offers additional information on current operation conditions and has a programmable memory.
2.2. The Loading System
The DXT is equipped with a separate loading station, independent of the fusing belt.
Advantages:• Separate on/off functions independent from fusing belt for loading and
fusing belts, avoiding errors• Misfusions easily avoided in the event of improper loading• Effortless and smooth transfer from loading to fusing belts due to synchronized systems• Comfortable working conditions for operators at unheated loading station• Extended loading station accommodates oversized items or multiple
operators to maximize machine usage
8
2.4. The Pressure System
After the heating system, the pressure system is the most important aspect of quality fusing. VEIT Kannegiesser is known for its leading pressure technology, the most underestimated aspect of a fusing machine. Our unique modular pressure system meets individual client needs through customized configurations.
DXT 1400L/1600 C Standard Pressure SystemApplicable for a broad range of modern fabrics used in sportswear, this system provides problemfree fusing with light to middle weight fabrics.
DXT 1400L/1600 CU Double Pressure SystemApplicable for difficulttofuse fabrics or those with elasticity, the double pressure systems are individually con trolled, allowing for different pressures to be applied and offering our clients great flexibility and avoidance of pressure problems. Both pairs of pressure rollers operate independently from each other and offer continuous loading.
DXT 1400L/1600 CFCFLEXO Double Pressure SystemThe combination of FLEXO and standard pressure systems serves as the definitive answer for all applications. The airfilled FLEXO rollers offer flexibility as they adjust to the fabric and are especially effective on pressure sensitive fabrics. Both the FLEXO and standard pressure rollers operate independently from each other and allow continuous loading.
Advantages:• Three options – Standard, Double, or FLEXO Double Pres
sure systems• Both double pressure systems
offer a broad range of pressure variations for various fabric and interfacing combinations
• Pressure is always indicated in bar or N/cm² and will be
automatically converted
Top Bottom
The thermically efficient and energy saving heating elements are at the cutting edge of today’s fusing machine technology.The Heat Zone Configuration – Bottom or TopA special feature of this machine is the availability of various heat zone configurations, allowing for customization to meet individual client needs. The ability to convert from one configuration to the other for specific applications is unique to this machine. The DXT is equipped with an extended heat contact chamber, allowing higher speed of the fusing belt and thereby increasing productivity.The Heating ElementAluminum profile construction optimizes energy efficient heat transfer.
Advantages:• Uniform surface temperature • Minimal heat loss due to optimal
heat transfer• Rapid temperature change• Precision temperature control
with minimal fluctuations• Specially insulated heating elements for minimal energy
waste
2.3. The Heating System
9
Advantages:• Separately controlled and
adjusted upper and lower heat zones, individually adjustable for various fabric and interlining combinations
• Clear, simple color display with temperature control to prevent too low or too high temperatures
• Diagnostic system for belt progression, electrical supply and compressed air supply
3.1. The Control Unit
Control of the fusing parameters is of utmost importance in a fusing machine, where all important details can be overseen in a clear and readable manner. Fluctuations in temperature are highlighted to draw quick attention.
Advantages:• Sturdy, compact design requires
minimal fl oor space• Extended heat chamber • Rapid machine warmup• Totally reliable and adjustable/
maintains accurate temperature and pressure
3. FuseMaster BX 600/1000 Series – The Compact Solution
Designed for daily use in outerwear or dress shirt productions. This sturdy and reliable machine is the optimal solution in both cases.
10
3.3. The Pressure System
The precise pressure for successful fusing of different interlinings and fabrics varies; therefore, a pressure system must be able to address these needs. The BX is the only fusing machine in its class offering a choice of two pressure systems to best meet the needs of our clients.
3.2. The Heating System
As with all continuous VEIT Kannegiesser fusing machines, our special heating elements play an important role. Clearly defined heat zones provide for optimal fusing results.
Advantages:• Uniform surface temperature
due to curved heat zone • Minimal heat loss due to optimal
heat transfer• No gaps between heating ele
ments, facilitating uniform heat distribution
• Rapid temperature change• Precision temperature control • Specially insulated heating ele
ments for minimal energy waste
Advantages:• Current roller combinations can
be chosen between soft and medium
• Fast exchange of pressure rollers possible at any time
BX 600/1000 S (soft)Applicable for pressure sensitive fabrics used in sportswear and especially in women’s and men’s apparel
BX 600/1000 M (medium) Applicable for common fusing applications in goods with hightwist yarns and dress shirt industry
11
Waistband Fusing Device (for EX, DXT, BX)Continuous roll to roll fusing is possible for trouser and skirt waistbands.
Advantages:• Ideal for minimal work space• Accommodates two independent
operators
Rotating Strip-Off Device (for EX)Through rotation of stripoff device along the upper belt, pieces adhering to the belt are gently and effectively removed.
Return-to-Operator System – RF (for EX 1000, BX)A returntooperator system is especially benefi cial for smaller production runs, allowing a single operator to both load and unload the machine.
4. Options for the EX, DXT and BX Series
Lateral Loading Tables(for EX-FE, DXT)For preparation of oversized pieces, the fusing machine can be equipped with lateral loading tables.
Advantages:• All waistbands for one particular
product are on one roll, maintaining product integrity
• Fusing occurs according to a continuous sequence
Advantages:• Gentle removal of pieces from the upper belt with rubber ridges• Unique design allows damaged ridges to be replaced individually without
removal of the entire stripoff device, facilitating rapid and cost effective repair
• Low maintenance
12
5. Loading Systems for EX, DXT and BX SeriesA loading system may be incorporated for even more effi cient use of the fusing machine.
FE-L Loading System The VEIT Kannegiesser FEL is an extended version of the FE loading belts in the EX series. The FEL can either be added to extend the standard FE loading belts or can be installed instead of the standard FE loading belts. An extended loading zone allows for additional operators.
Advantages:• Foot switch can be used to start
and stop the belt• Oversized pieces can be pro
cessed• Additional operators can be
utilized for loading• FEL can be installed on both
the EX and DXT• As an additional installation –
4400 mm (176 in)• As the primary installation –
3000 mm (120 in)
ET Timed Loading BeltThe ET timed loading belt is an additional function of the FE. As an accessory to the assembly belt, a timed belt acts as a buffer between the rapid speed of the loading belt to the slower moving feeding belt.
Advantages:• Choice of cycles including timed,
continuous or coupled lanes • Pieces positioned precisely on a
motionless belt• Independent functioning of
adjacent belts• Automatic speed adjustment of
the timing belt
13
V-AST StackerIt is important that fused assemblies be handled gently to allow them to cool prior to further processing.
The VEIT Kannegiesser VAST Stacker guides the fused assemblies from the loading system’s cooling belt to the unloading table. At this point the unloading table is activated by a sensor and moves under the piece until the entire length is transferred. Thereafter, the unloading table returns to its position under the belt to receive the next piece. This system is compatible with the EX, DXT and BX series loading systems and stacker lanes can be coupled to accommodate unusually large assemblies.
Advantages:• Automatic stacking of fused
assemblies• Choice of various belt widths• Coupling of stacker lanes for
extra wide pieces• Flat transfer of fused assemblies• Pieces placed in order• Pieces placed for precise bundling
6. AX 450 – The Compact Fusing MachineDespite its minimized dimensions, the AX 450 offers the same attributes as the larger models. It can be utilized for fusing waistbands as well as fullfl edged fusing of sportswear and dress shirts.
Advantages:• Fullfl edged fusing for small production runs, labs or assembly lines• Requires no compressed air• Single phase electrical connection• Rolling stand design• Partial fusing capabilities
14
6.1. The Control Unit
Even our compact fusing machine comes equipped with a fullfl edged control unit.
6.2. The Heating System
The heat technology and heat zone confi gurations are incorporated from our larger fusing machines, guaranteeing maximum quality.
Advantages:• Unique in its class, a diagnostic
system for heating elements, motor control and belt control
• Clear, simple color display for under or over heating
• Calibrated thermostat, necessary for belt exchange or
different belt types• Set/actual temperature monitoring
Advantages:• Separate upper and lower heat
zones• Proven VEIT Kannegiesser
surface heat technology with uniform surface distribution
• Minimal energy usage, with each outlet serviced by 16 amp fuse
• Panel heating elements provide specifi c heat transfer with minimal energy waste
Heating SystemPressure System
Heat zonelength 600 mm
15
6.3. The Pressure System
The AX 450 has a sophisticated mechanical pressure system which operates without compressed air and yet delivers precise pressure. Pressure specifications are shown in N/cm², as requested by leading interfacing suppliers.
Advantages:• Requires no compressed air• Pressure adjustable from 0 N/cm2 to 33 N/cm2
• Low maintenance system• Precision adjustments
6.4. Options
Unloading SlideAccommodates large and small fused assemblies for cooling
Waistband Fusing DeviceVarious options are available for mechanical unwinding and rewinding for waistband fusing. The waistband fusing device may be operated individually or by two people. We further recommend a loading guide for accurate positioning of the face fabric and the interlining.
Mechanized Rewinding “Stretch”We offer an electronically driven option for rewinding fused waistbands of elastic fabrics, eliminating stretch.
16
Advantages:• Exact and separate temperature
adjustments for upper and lower heating zones
• Uniform surface heat distribution over the entire fusing width
• Panel heating elements provide specific heat transfer with minimal energy waste
7.2. The Heating System
As with all VEIT Kannegiesser fusing machines, the BH 600 is equipped with our proven panel heating technology.
7. BH 600 – Shirt Fusing MachineSpecifically designed for fusing dress shirt collars and cuffs, this machine is equipped with an active cooling system and is operated by one person. When equipped with the BH/CH ST 600 Stacker, an optical sensor causes all fused assemblies to be collected automatically.
7.1. The Control Unit
Reliability in terms of fusing parameters are essential for the fusing operation. A clear display of those parameters on the fusing machineis important for the operator to main tain an even quality.
Advantages:• Can be operated by one person• Proven VEIT Kannegiesser panel
heating technology• Active Cooling System for fused
assemblies• Optional stacker available
Advantages:• Clear display of fusing parameters• Clearly visible by seated operator• Diagnostic system for heating
elements, motor control and belt progression
• Clear, simple color display with temperature control to prevent too low or too high temperatures
• Set/actual temperature monitoring• Control indicators for active
cooling system
Heating SystemPressure System
17
7.3. The Pressure System
The pressure system for fusing dress shirts is very important, because most adhesive resins for shirts require high pressure. With the BH 600, the fused assembly is held under additional contact pressure after proceeding through the initial pressure system.
7.4. Options
BH ST 600 StackerCan be retrofi tted or factory installed. This stacker straightens and stacks fused assemblies.
Advantages:• Pressure adjustable from 0 N/cm2 to 46 N/cm2
• Large return drum delivers contact pressure, ensuring successful adhesion
Advantages:• Optical sensor activation• Collars and cuffs stacked for
precise bundling
8.1. The Control Unit
Various work modes may be selected from the control panel, including an automatic mode which allows conti-nuous loading. Temperature, timing and pressure are all individually ad-justable.
Collars are guided through the press-ing and heating stations by a timing belt. They are then pressed accord-ing to the preset temperature and pressure. When the timer expires, fused assemblies proceed to the cooling station where they are cooled under applied pressure while the next collars are guided into the heating station. After the cycle is completed, the cooled fused assemblies are guided to the single operator unload-ing station.
Advantages:• Excellent adhesion• Active cooling system, allowing
for immediate further processing• Automatic cycle adjustments
provide highly effective cooling• Requires no compressed air• High collar output
VEIT Kannegiesser‘s state-of-the-art hydraulic press „Hercules“ achieves an unrivaled adhesion quality. The ex-cellent pressure system is combined with a strong, reliable heating system and is mainly used in the classic dress shirt industry.
8. HKH 5, 6/7 Hydraulic Fusing Press
Heating SystemWater cooling
18
Technical Data Continuous Fusing Machines
Model Fusing Widthmm
(inch)
Belt Speedm/min(ft/min)
Air Pressure Volume
Ø=8 mm bar
ElectricalVolt /Hz/kW
Dimensions: L x W x Hmm
(inch)
Weightkg(lb)
AirConsumption
l/min
EX 1000 C SB 1000(40)
1.0 - 10(3.4 - 34)
6.5 3 x 400/50-60/23 3900 x 1570 x 1570(156 x 63 x 63)
980(2156)
50
EX 1000 CU SB 1000(40)
1.0 - 10(3.4 - 34)
6,5 3 x 400/50-60/23 4100 x 1570 x 1570(164 x 63 x 63)
1080(2376)
50
EX 1000 CFC SB 1000(40)
1.0 - 10(3.4 - 34)
6,5 3 x 400/50-60/23 4100 x 1570 x 1570(164 x 63 x 63)
1080(2376)
50
EX 1000 C, FE 1000(40)
1.0 - 10(3.4 - 34)
6,5 3 x 400/50-60/23 4540 x 1570 x 1570(164 x 63 x 63)
1100(2420)
50
EX 1000 CU FE 1000(40)
1.0 - 10(3.4 - 34)
6,5 3 x 400/50-60/23 4720 x 1570 x 1570(261 x 63 x 63)
1200(2640)
50
EX 1000 CFC FE 1000(40)
1.0 - 10(3.4 - 34)
6,5 3 x 400/50-60/23 4720 x 1570 x 1570(261 x 63 x 63)
1200(2640)
50
EX 1400 C SB 1400(56)
1.0 - 10(3.4 - 34)
6,5 3 x 400/50-60/30.5 3900 x 1970 x 1570(156 x 78 x 63)
1220(2684)
50
EX 1400 CU SB 1400(56)
1.0 - 10(3.4 - 34)
6,5 3 x 400/50-60/30.5 4100 x 1970 x 1570(164 x 78 x 63)
1350(2970)
50
EX 1400 CFC SB 1400(56)
1.0 - 10(3.4 - 34)
6,5 3 x 400/50-60/30.5 4100 x 1970 x 1570(164 x 78 x 63)
1350(2970)
50
EX 1400 C FE 1400(56)
1.0 - 10(3.4 - 34)
6,5 3 x 400/50-60/30.5 4540 x 1970 x 1570(182 x 78 x 63)
1300(2860)
50
EX 1400 CU FE 1400(56)
1.0 - 10(3.4 - 34)
6,5 3 x 400/50-60/30.5 4720 x 1970 x 1570(261 x 78 x 63)
1430(3146)
50
EX 1400 CFC FE 1400(56)
1.0 - 10(3.4 - 34)
6,5 3 x 400/50-60/30.5 4720 x 1970 x 1570(261 x 78 x 63)
1430(3146)
50
DXT 1400 L C, CU, CFC
1400(56)
1.7 - 10(5.5 - 34)
6,5 3 x 400/50-60/42 5125 x 1970 x 1270(234 x 78 x 52)
1440(3168)
50
DXT 1600 C, CU, CFC
1600(64)
1.7 - 10(5.5 - 34)
6,5 3 x 400/50-60/48 5125 x 1970 x 1270(234 x 78 x 52)
1600(3520)
50
BX 600 600(24)
1.7 - 10(5.5 - 34)
6,5 3 x 400/50-60 /10,8 3600 x 1150 x 1500(144 x 46 x 60)
520(1144)
50
BX 1000 1000(40)
1.7 - 10(5.5 - 34)
6,5 3 x 400/ 50-60/17.5 3600 x 1150 x 1500(144 x 46 x 60)
670(1474)
50
AX 450 450(18)
1.6 - 10(5.4 - 34)
– 1 x 230/50-60/3,6 2050 (82)** x 930 (37)*** x 470/290/340
(18/12/14)****
290/340*(638/748)*
–
BH 600 600(24)
1.0 - 2.5(3.4 - 8.2)
6,5 3 x 400/50-60/9.5 1560 x 1060 x 1550(62 x 42 x 61)
470(1036)
1
MultiStar DXT Series: standard machine with cooling station; loading width with loading stationAX 450: * with base frame / ** without loading guide / *** with entry table / **** without base frame
19
Technical Data
Subject to alterations. All specifications have been made to the best of our knowledge, Special voltage upon request. Pictures can include optional equipment. All standard measurements are approximate.
Options
Model Working Width mm
(inch)
Loading Length
mm(inch)
Air Pressure Volume 6
barD=8 mm
ElectricalVolt /Hz/kW
Dimensions: L x W x Hmm
(inch)
Weightkg(lb)
Air Con-sumption
l/min
Lanes
FEL 950(38)
3000(120)
– 1 x 230/5060/0.25 3130 x 1110 x 850950(125 x 44 x 3038)
250(550)
– 1
ET 4.5 / 14 450(18)
1400(56)
– 3 x 400/5060/2 3130 x 1200 x 980(125 x 48 x 39)
300(660)
– 2
VAST 10 1000(40)
– 4 3 x 400/5060/1.4 /3 x 230/5060/1.4
3260 x 1430 x 830845(130 x 57 x 3334)
820(1804)
45 –
VAST 14 1400(56)
– 4 3 x 400/5060/1.4 / 3 x 230/5060/1.4
3260 x 1855 x 830845(130 x 74 x 3334)
920(2024)
45 –
VAST 16 1600(64)
– 4 3 x 400/5060/1.4 / 3 x 230/5060/1.4
3260 x 2030 x 830845(130 x 81 x 3334)
1050(2310)
45 –
Hydraulic Fusing Press
Model Working Sur-face Height
mm(inch)
Plate PressDimension
mm(inch)
ElectricalVolt /Hz/kW
Dimensions: L x W x Hmm
(inch)
Weightkg(lb)
HKH 5.6/7 770(31)
560 x 700(22 x 28)
3 x 400/50/12.5 3100 x 1350 x 1070(122 x 53 x 42)
1450(3190)
Pressure Values for Fusing machines
Model and pressure system pressure in bar pressure in N / cm²
AX 450 mechanical 0 33 N/cm²
BH 600 1 6 6 46 N/cm²
BX 600 Soft 1 6 2 44 N/cm²
BX 600 Medium 1 6 4 49 N/cm²
BX 1000 Soft 1 6 2 44 N/cm²
BX 1000 Medium 1 6 4 49 N/cm²
EX EXT 1000 Soft 1 6 2 44 N/cm²
EX EXT 1000 Medium 1 6 4 49 N/cm²
EX EXT 1000 Hard 1 6 8 58 N/cm²
EX EXT 1400 Soft 1 6 1 31 N/cm²
EX EXT 1400 Medium 1 6 2 36 N/cm²
EX EXT 1400 Hard 1 6 2 44 N/cm²
Pressing for Excellence
VEIT GmbH JustusvonLiebigStr. 15D86899 Landsberg/LechGermanyTel. +49 (8191) 4790Fax +49 (8191) 479149EMail: [email protected]group.com
VEIT GmbHGTT BranchValdorfer Str. 100D32602 Vlotho · GermanyTel. +49 (5733) 87 130 Fax +49 (5733) 87 1345 EMail: info@veitkannegiesser.de www.veitkannegiesser.com
BRISAY-Maschinen GmbH Mittelweg 4D63762 GrossostheimRingheimGermanyTel. +49 (6026) 9970Fax +49 (6026) 997100EMail: [email protected] Su
bjec
t to
alt
erat
ions
. A
ll sp
ecif
icat
ions
hav
e be
en m
ade
to t
he b
est
of o
ur k
now
ledg
e. P
rint
ed i
n G
erm
any.
Inf
o N
o. 3
3/05
11
Pressing for Excellence – Why you can depend on the VEITGroup
For over 50 years, the needs and the challenges of our customers have been our most important undertaking. For decades, world famous brands in the German and international garments industry have placed confidence in the innovative, high quality products and services offered by the VEITGroup.
Our experts consult and partner with you in finding the best possible solution for your project needs, whether you require individual machines or a complete product line.
Prompt delivery and professional installation of our machines and systems go hand in hand with premium training, through which we equip your staff with the skills necessary to achieve the highest possible production.
Worldwide 24-Hour Service HotlineOur service technicians are always available, around the world and around the clock, maximizing continuous production.
We look forward to dealing with you personally!
Your local sales agent:
![Endrich News Oktober 2017 dt+engl · Type C 2.5 W PERFORMANCE TYPE FUSING POWER [ FUSING TIME. ] ANCE FUSING PERFORMANCE FUSING PERFORMANCE Please note that this device](https://static.documents.pub/doc/80x56/5f68c7cca7d617432e4d41da/endrich-news-oktober-2017-dtengl-type-c-25-w-performance-type-fusing-power-fusing.jpg)