TM SERIES100 t–450 tTM SERIES
TM 100 t–450 t
PLASTICS TECHNOLOGY
INJECTION MOLDING TECHNOLOGY
2
100 t–450 t
Plastics TechnologyBATTENFELD
SPECIAL FEATURESand benetits of theTM SERIES
SPECIAL FEATURESand benefits of theTM SERIES 100 t–450 t
Clamping system
The clamping cylinder is equipped with differential gears to promote high opening and closing speeds, and to minimize dry cycle times.
Linear guides
Support for the moving platen is provid-ed by high-precision linear guides, which dispenses with the need for special adjustments to accommodate heavy molds. Lubrication is reduced to a mini-mum. The hard-chrome-plated tie-bars are free of contamination with lubricants.
Clamping platens
Rigid machine frame combined with reinforced cap bolts and low-mainte-nance toggle sleeves stand for high precision, low maintenance and long service life.
3
The compact power packages in a great machine series in 3 – platen technology with a 5-point toggle system.
Newly designed in the 100 to 450 t clamping force range, TM models stand for ultimate performance, short footprint, simple operation and maintenance, energy savings and cost-efficiency.
Proven features have been retained, with a number of beneficial new features added.
The high-performance control system offers numerous process monitoring and documentation facilities.
Thanks to a wide range of options, the TM is extremely versatile and lends itself to many special processes, such as injection-compression.
Put the TM to the test and see for yourself!
Energy-saving DFEE drive
This flexible drive concept based on electrically adjust-able (DFEE) delivery pumps promotes short cycle times. A further increase in injection performance throughparallel movements can easily be achieved by installing an additional pump system. Parallel strokes, higher injection and dosing performance can easily be achieved with an optional twin pump system!
Injection units equipped
with linear guides
and a service lifting mechanism to facilitate maintenance and the remo-val of barrels and screws.
Screws with a uniform
L/D ratio
of 22:1 and an injection pressure of 2,000 bars for the medium-diameter screws ensure excellent melt homo-geneity.
Screws equipped with
direct hydraulic drive
A high-performance hydraulic motor ensures a high plasticizing performance.
4
100 t–450 t
Plastics TechnologyBATTENFELD
CLAMPING UNIT TMCLAMPING UNIT TM100 t–450 t
OUTSTANDING FEATURES OF THE TM
short footprintextremely rigid, sturdy clamping plates and machine frameprecise platen parallelism across the entire strokelow-maintenance linear guides to support the moving platenself-locking 5-point toggle systemreinforced toggle bearings with low-maintenance toggle sleeves
adhesive central oil lubrication of toggle jointshigh opening and closing speeds thanks to differential gearsshort dry cycle timesflexible parts removal in three directionshigh repeatability of all parameter settingssensitive mold safety devicemold protection thanks to precise platen parallelism, minimal platen deflection and linear guideslow-maintenance and service-friendly design of all machine parts
5
NEW INJECTION UNITS
for more flexibility
Short footprint with two pulling cylinders
High injection rates
Universal compatibility of barrels with different injection units
ULTIMATE PRECISION
and repeatability
Compact design with integrated hydraulic block and easy access to all components
Direct screw drive via low-speed hydraulic motor with optimal adaptation to individual plasticizing demands
Ultimate repeatability thanks to controlled servo-valve
A CONCEPT for improved parts quality
Optimized melt homogeneity thanks to a uniform L/D ratio of 22:1 and an injection pressure of 2000 bar with medium-diameter screws
Linear guide systems ensure precise axial move-ments of the injection unit
Carriage cylinders positioned opposite each other provide momentum-free nozzle carriage
Plasticizing systems for injection molding machines must fulfill many different requirements. By applying a universal L/D ratio of 22:1 to the three screw sizes available for each injection unit, the processing window has been optimized to meet rising quality standards.
INJECTION UNITINJECTION UNITup to 5100
HIGH-PERFORMANCEPLASTICIZING SYSTEMSHIGH-PERFORMANCEPLASTICIZING SYSTEMS
6
Plastics TechnologyBATTENFELD
10 membrane keys with luminous rings are provided to control the main ma-chine functions (drive motor, heating system, operation modes)
2 USB interfaces to connect storage media (USB sticks, printer, keyboard) or devices for programming an access authorization system with passwords are also available.2 additional USB inter-faces and 2 Ethernet interfaces are located at the rear of the control cabinet.
Thanks to increased data processing capacity, functions such as the extended quality table with 12columns have become possible. The evaluation is now based on a memory depth of 10,000 shots, with all deactivated parameters also being recorded in the background.
The complete machine documentation including manuals, drawings of spare parts and parts lists is also available online. In addition, users can insert their own PDF files and make them available to machine operators.
The UNILOG B6 is a new generation of control sys-tems, setting new benchmarks in user friendliness, speed and precision.
Continuity of the Battenfeld operating system and familiar symbols is maintained by incorporating ele-ments from previous generations of control systems, however with an extended graphical operator inter-face.
15” TFT color screen with unlimited touch screen functions for operation and display
Space provided for a further 7 optional mechanical switches/keys
2 rows of soft keys to select various machine functions
48 membrane keys to operate machine axes and application options
UNILOG B6UNILOG B6
A high-performance system concept that has been optimized for perfect coordination with the machine’s hydraulics and system of sensors to ensure fast and precise movements of all machine axes. Precise analysis of all relevant process variables provides the user with the necessary control facilities for demand-ing applications.
7
PP + 20% Talc
PP + 40% Talc
PP + 20% GF
PS
PVC-hart
PVC-weich
SAN
SB
PF
UP
Material Factor
ABS 0,880,88
CA 1,021,02
CAB 0,970,97
PA 0,910,91
PC 0,970,97
PE 0,710,71
PMMA 0,940,94
POM 1,151,15
PP 0,730,73
Material Factor
0,850,85
0,980,98
0,850,85
0,910,91
1,121,12
1,021,02
0,880,88
0,880,88
1,31,3
1,61,6
Clamping unit
to 210 350 525 750 1000 1330 2250 3400 5100
100 • • •• • •160 • • •• • •210 • • •• • •270 • • •• • •350 • • •• • •450 • • •• • •
POSSIBLE COMBINATIONS OF CLAMPING UNITS/INJECTION UNITS
The maximum shotweights (g) are calculated by multiplyingthe theoretical shot volume (cm³) by the above factor.
Dark grey boxes =Thermosets
SHOT WEIGHT CONVERSION TABLE
Injection unit
CLAMPING/INJECTION UNITSHOT WEIGHTCLAMPING/INJECTION UNITSHOT WEIGHT
8
TM 100/...
1000 / 1100
420 x 420
200 …. 450
380
830
140 / 26,4
1,5 - 294
.../210 .../350 .../525
25 30 35 30 35 40 35 40 45
150 175 200
22 22 22
73,6 106 144 123 169 220 193 251 318
2940 2042 1500 2835 2083 1595 2743 2100 1659
372 298 238
9,9 14,4 22,3 11,6 17,9 28,5 14,3 22,8 29,7
490 621 770
250 / 86 250 / 86 350 / 86
71,4 103 140 74,1 101 132 76,6 100 127
95 137 187 99 135 176 102 133 169
155 223 303 216 294 384 287 375 475
15 15 15
250 250 250
32 / 61 34 / 63 36 / 65
4300 4300 4400
3,9 x 1,4 x 2,0 4,1 x 1,4 x 2,0 4,4 x 1,4 x 2,0
750 / 315 750 / 315 750 / 315
TM
10
0T
M 1
00 Clamping unit
Clamping force / locking force kN
Distance between tier-bars mm x mm
Mold height mm
Opening stroke mm / kN
Maximum daylight mm
Ejector force mm /kN
Dry cycle time 1) s - mm
Injection unit
Screw diameter mm
Screw stroke mm
Screw L/D ratio mm
Theoretical shot volume cm³
Specific injection pressure bar
Max. screw speed min-1
Max. plasticizing rate (PS) 2) g / s
Max. screw torgue Nm
Nozzle stroke / nozzle contact force mm / kN
Injection rate into air cm³/s
Injection rate into air with twin-pump (option) cm³/s
Injection rate into air with hydraulic accumulator (option) cm³/s
Drive
Drive power kW
Oil tank volume l
electrical power supply without/with Europackage kVA
Weights, dimensions
Netweight (exclusive oil) kg
lenght x width x weight 3) m
max. mold weight /min. mold diameter 4) kg / mm
1) according to Euromap 6 2) according to Battenfeld norm, higher plasticizing rates possible with twin-pump (option) 3) max. length with middle screw diameter in back position 4) max. 2/3 on clamping platen
9
TM 160/...
1600 / 1760
520 x 520
225 …. 550
480
1030
180 / 41,2
1,8 - 364
.../525 .../750 .../1000
35 40 45 40 45 50 45 50 55
200 225 250
22 22 22
193 251 318 283 358 442 398 491 594
2743 2100 1659 2678 2116 1714 2490 2016 1666
378 291 190
22,7 36,2 47,1 27,9 36,3 43,9 23,7 28,6 35,5
770 998 1540
350 / 86 350 / 86 400 / 100
121 158 200 124 157 194 134 165 200
172 225 285 176 223 276 190 234 284
287 375 475 376 476 588 478 590 714
22 22 22
350 350 350
43 / 72 46 / 75 47 / 76
6300 6400 7100
4,8 x 1,5 x 2,1 5,0 x 1,5 x 2,1 5,3 x 1,5 x 2,1
1400 / 400 1400 / 400 1400 / 400
TM
16
0T
M 1
60Clamping unit
Clamping force / locking force kN
Distance between tier-bars mm x mm
Mold height mm
Opening stroke mm / kN
Maximum daylight mm
Ejector force mm /kN
Dry cycle time 1) s - mm
Injection unit
Screw diameter mm
Screw stroke mm
Screw L/D ratio mm
Theoretical shot volume cm³
Specific injection pressure bar
Max. screw speed min-1
Max. plasticizing rate (PS) 2) g / s
Max. screw torgue Nm
Nozzle stroke / nozzle contact force mm / kN
Injection rate into air cm³/s
Injection rate into air with twin-pump (option) cm³/s
Injection rate into air with hydraulic accumulator (option) cm³/s
Drive
Drive power kW
Oil tank volume l
electrical power supply without/with Europackage kVA
Weights, dimensions
Netweight (exclusive oil) kg
lenght x width x weight 3) m
max. mold weight /min. mold diameter 4) kg / mm
1) according to Euromap 6 2) according to Battenfeld norm, higher plasticizing rates possible with twin-pump (option) 3) max. length with middle screw diameter in back position 4) max. 2/3 on clamping platen
10
TM 210/...
2100 / 2310
570 x 570
250 …. 600
530
1130
180 / 41,2
2,1 - 399
.../750 .../1000 .../1330
40 45 50 45 50 55 50 55 65
225 250 275
22 22 22
283 358 442 398 491 594 540 653 913
2678 2116 1714 2490 2016 1666 2470 2041 1461
398 260 207
38,1 49,6 60 32,4 39,2 48,5 31,2 38,7 46,2
998 1540 1940
350 / 86 400 / 100 400 / 100
170 215 265 183 226 273 184 223 311
222 281 347 239 296 357 241 292 407
376 476 588 478 590 714 567 686 958
30 30 30
400 400 400
55 / 84 57 / 86 60 / 89
8100 8800 9000
5,2 x 1,6 x 2,3 5,5 x 1,6 x 2,3 5,6 x 1,6 x 2,3
1800 / 500 1800 / 500 1800 / 500
TM
210
TM
210 Clamping unit
Clamping force / locking force kN
Distance between tier-bars mm x mm
Mold height mm
Opening stroke mm / kN
Maximum daylight mm
Ejector force mm /kN
Dry cycle time 1) s - mm
Injection unit
Screw diameter mm
Screw stroke mm
Screw L/D ratio mm
Theoretical shot volume cm³
Specific injection pressure bar
Max. screw speed min-1
Max. plasticizing rate (PS) 2) g / s
Max. screw torgue Nm
Nozzle stroke / nozzle contact force mm / kN
Injection rate into air cm³/s
Injection rate into air with twin-pump (option) cm³/s
Injection rate into air with hydraulic accumulator (option) cm³/s
Drive
Drive power kW
Oil tank volume l
electrical power supply without/with Europackage kVA
Weights, dimensions
Netweight (exclusive oil) kg
lenght x width x weight 3) m
max. mold weight /min. mold diameter 4) kg / mm
1) according to Euromap 6 2) according to Battenfeld norm, higher plasticizing rates possible with twin-pump (option) 3) max. length with middle screw diameter in back position 4) max. 2/3 on clamping platen
11
TM 270/...
2700 / 2970
630 x 630
250 …. 650
600
1250
200 / 59
2,4 - 441
.../1000 .../1330 .../2250
45 50 55 50 55 65 55 65 75
250 275 325
22 22 22
398 491 594 540 653 913 772 1078 1436
2490 2016 1666 2470 2041 1461 2500 2070 1555
350 278 248
43,6 52,8 65,3 41,9 51,9 62 46,5 70 105
1540 1940 2373
400 / 100 400 / 100 500 / 129
246 304 368 248 300 419 212 296 394
330 408 494 333 403 563 284 397 529
478 590 714 567 686 958 726 1014 1351
37 37 37
550 550 550
57 / 86 60 / 89 71 / 100
10600 10800 11800
5,7 x 1,7 x 2,3 5,8 x 1,7 x 2,3 6,7 x 1,7 x 2,3
2400 / 500 2400 / 500 2400 / 500
TM
270
TM
270Clamping unit
Clamping force / locking force kN
Distance between tier-bars mm x mm
Mold height mm
Opening stroke mm / kN
Maximum daylight mm
Ejector force mm /kN
Dry cycle time 1) s - mm
Injection unit
Screw diameter mm
Screw stroke mm
Screw L/D ratio mm
Theoretical shot volume cm³
Specific injection pressure bar
Max. screw speed min-1
Max. plasticizing rate (PS) 2) g / s
Max. screw torgue Nm
Nozzle stroke / nozzle contact force mm / kN
Injection rate into air cm³/s
Injection rate into air with twin-pump (option) cm³/s
Injection rate into air with hydraulic accumulator (option) cm³/s
Drive
Drive power kW
Oil tank volume l
electrical power supply without/with Europackage kVA
Weights, dimensions
Netweight (exclusive oil) kg
lenght x width x weight 3) m
max. mold weight /min. mold diameter 4) kg / mm
1) according to Euromap 6 2) according to Battenfeld norm, higher plasticizing rates possible with twin-pump (option) 3) max. length with middle screw diameter in back position 4) max. 2/3 on clamping platen
12
TM 350/...
3500 / 3850
710 x 710
300 …. 710
670
1380
200 / 59
2,7 - 497
.../1330 .../2250 .../3400
50 55 65 55 65 75 65 75 85
275 325 375
22 22 22
540 653 913 772 1078 1436 1244 1657 2128
2470 2041 1461 2500 2070 1555 2500 2022 1574
318 283 178
48 59,3 70,9 53 79 120 50 76 107
1940 2373 3759
400 / 100 500 / 129 600 / 129
283 343 479 242 338 450 260 346 445
368 446 623 315 440 585 338 450 578
567 686 958 726 1014 1351 1040 1385 1779
45 45 45
650 650 650
78 / 107 90 / 119 94 / 123
14400 15400 16400
6,0 x 1,8 x 2,5 6,9 x 1,8 x 2,5 7,1 x 1,8 x 2,5
3200 / 500 3200 / 500 3200 / 500
TM
350
TM
350 Clamping unit
Clamping force / locking force kN
Distance between tier-bars mm x mm
Mold height mm
Opening stroke mm / kN
Maximum daylight mm
Ejector force mm /kN
Dry cycle time 1) s - mm
Injection unit
Screw diameter mm
Screw stroke mm
Screw L/D ratio mm
Theoretical shot volume cm³
Specific injection pressure bar
Max. screw speed min-1
Max. plasticizing rate (PS) 2) g / s
Max. screw torgue Nm
Nozzle stroke / nozzle contact force mm / kN
Injection rate into air cm³/s
Injection rate into air with twin-pump (option) cm³/s
Injection rate into air with hydraulic accumulator (option) cm³/s
Drive
Drive power kW
Oil tank volume l
electrical power supply without/with Europackage kVA
Weights, dimensions
Netweight (exclusive oil) kg
lenght x width x weight 3) m
max. mold weight /min. mold diameter 4) kg / mm
1) according to Euromap 6 2) according to Battenfeld norm, higher plasticizing rates possible with twin-pump (option) 3) max. length with middle screw diameter in back position 4) max. 2/3 on clamping platen
13
TM 450/...
4500 / 4950
800 x 800
300 …. 770
760
1530
250 / 81
3,0 - 560
.../2250 .../3400 .../5100
55 65 75 65 75 85 75 85 95
325 375 425
22 22 22
772 1078 1436 1244 1657 2128 1878 2412 3012
2500 2070 1555 2500 2022 1574 2500 2110 1689
389 244 152
72 107 160 68 104 146 65 91 118
2373 3759 6048
500 / 129 600 / 129 600 / 129
333 465 619 358 476 612 355 456 570
363 507 675 390 519 668 387 497 622
726 1014 1351 1040 1385 1779 1291 1659 2072
55 55 55
800 800 800
102 / 131 106 / 135 111 / 140
19300 20300 21300
7,4 x 2,0 x 2,5 7,6 x 2,0 x 2,5 8,0 x 2,0 x 2,5
4000 / 630 4000 / 630 4000 / 630
TM
450
TM
450Clamping unit
Clamping force / locking force kN
Distance between tier-bars mm x mm
Mold height mm
Opening stroke mm / kN
Maximum daylight mm
Ejector force mm /kN
Dry cycle time 1) s - mm
Injection unit
Screw diameter mm
Screw stroke mm
Screw L/D ratio mm
Theoretical shot volume cm³
Specific injection pressure bar
Max. screw speed min-1
Max. plasticizing rate (PS) 2) g / s
Max. screw torgue Nm
Nozzle stroke / nozzle contact force mm / kN
Injection rate into air cm³/s
Injection rate into air with twin-pump (option) cm³/s
Injection rate into air with hydraulic accumulator (option) cm³/s
Drive
Drive power kW
Oil tank volume l
electrical power supply without/with Europackage kVA
Weights, dimensions
Netweight (exclusive oil) kg
lenght x width x weight 3) m
max. mold weight /min. mold diameter 4) kg / mm
1) according to Euromap 6 2) according to Battenfeld norm, higher plasticizing rates possible with twin-pump (option) 3) max. length with middle screw diameter in back position 4) max. 2/3 on clamping platen
14
Electrical componentsOperating voltage 230/400 V-3Ph, 50 Hz
Common voltage supply <=TM 160 with 230/400 V
Software for operating hours counter
Closing / Opening - 5 profile steps
Ejection forward/back - 3 profile steps
Nozzle forward/back - 3 profile steps
Injection / Holding pressure - 10 profile steps
Screw speed / Back pressure - 6 profile steps
Purging program
Stroke zero offset settings
Start-up program
Adjustable injection pressure limitation
Switchover to holding pressure MASTER / SLAVE by injection time, screw stroke/injection volume and injection pressure
Self-teaching temperature controller
Display of temperature inside electrical cabinet
Seven-day timer
Access authorization via USB interface
Access protection via password system
User programming system “APS”
Freely configurable screen pages “User page”
Freely configurable status bar
Physical, process-related units
15“TFT colour screen
Automatic dimming
Logbook with filter function
Hardcopy function
Notepad function
Internal data storage via USB connection or network
Online language selection
Online selection of imerial or metric units
Online operator manual
Time Monitoring
Quality table
Events protocol (logbook) for 10000 events
Cycle time analysis
Parts counter with good/bad part evaluation
12 Trend diagrams
12 SPC Charts
Actual value graphics with 16 curves
4 Envelope curves
Injection Integral supervision
Metering Integral supervision
Alarm message via E-MAIL
USB - 2x operating unit, 2x control cabinet
2 Ethernet interfaces inside electrical cabinet
Printing via USB connection or network
Paint RAL 9002 / RAL5002 ultramarine blue
STA
ND
AR
D F
EA
TU
RE
SS
TA
ND
AR
D F
EA
TU
RE
S
HydraulicHydraulic unit with variable pressure and speed axial piston pump
Oil filtration by fine flow filter with electrical clogging indicator
Oil level indicator with alarm
Closed-loop oil temperature control with oil pre-heating
Oil temperature monitoring
Oil tank with connections for external oil filtration
Separate hand keys for core pulls
Display of actual system preasure via touchscreen
Clamping unit
Clamping force adjustable via touchscreen
Closing and opening speed adjustable
Closing and opening force adjustable
Mould safety program
Moving platen supported by positioned linear guides
Platen drillings and register rings according to EUROMAP
Fixing holes for robot on top of the fixed platen according to EURO-MAP/VDMA
Hydraulic mold close inhibit, electrically monitored on operator side
Central hydraulic multi-stroke ejector, adjustable
Flexible parts removal from 3 directions
Injection unit
Injection closed loop controlled via servo valve (only with S-version)
Screw L/D=22 with check valve, screw and barrel nitrated
Thermocouple failure monitor
Maximum temperature supervision
Plug-in ceramic heater bands
Temperature control of feed throat integrated
Open nozzle
Swiveling injection unit up to .../1330 injection unit
Purge guard electrically monitored
Hopper of V2A stainless steel can be shut and emptied
Selectable barrel stand-by temperature
Physical units - bar, ccm, mm/s etc.
Screw protection
Linear bearings for the injection unit
Safety gate
Monitored safety gate, CE-confirmed
Maintenance-free safety gate locked by electromagnet
Safety gate free for mould change and handling by robot
Cooling and conditioning
Cooling-water flow controller with temperature gauges in return lines, up to 100t: 4-way, from 350t: 6-way
15
OP
TIO
NA
LFE
AT
UR
ES
OP
TIO
NA
L F
EA
TU
RE
S
Hydraulic E S
Hydraulic accumulator for fast injection incl. loading pump and par-allel ejector movement and core pull movement via double pump –– •
Extra large oil cooler • •Core pull movement and parallel ejection with DFEE double pump –– •
Core pull movement and parallel ejection incl. Fast injec-tion with DFEE double pump –– •
Injection parallel to clamp force build-up (with hydraulic accumulator) –– •
Hydraulic core pulls. Limit switch function according to EUROMAP 13. Pressure and speeds adjustable • •
Pneumatic core pull • •Pneumatic manifold for Mouldmaster nozzle (controlled 1 nozzle or more parallel in the mould) • •
Hydraulic manifold for Mouldmaster nozzle (controlling 1 nozzle or more parallel in the mould) • •
Filter in water inlet of oil cooler • •Adapter with ball valve on the oil tank for oil maintenance • •Separate bypass filtration unit • •
Clamping unit
Non-standard mould hight after customers request • •Isolation platens • •T-slots in mould platens • •SPI bolt pattern • •Ejector cross in clamping platen as per EUROMAP/SPI • •Maximum ejector force increased • •Mechanical ejector couple • •Ejector platen safety device • •Mechanical mould safety mechanism • •Unscrewing device with hydro-motor additional to standard ejector • •Parts chute for separation of good/bad parts • •Photoelectric ejection check • •Air valve, action initiated (ON) and timer (OFF) • •Quick mold clamping system magnet., hydr. or mech. –– •
Injection unitGrooves in the feeding zone • •High torque screw motor in lieu of standard • •High temperature heater bands (max. 450° C) • •Screw drive by a.c. servo-motor –– •Ball type screw tip • •Needle type shutoff nozzle with spring, pneumatic opera-ted or hydraulic operated • •
Melt temperature- or pressure sensor in cylinder head –– •Hydraulic cross-bolt type shutoff nozzle (from SPE2250) • •Open Airmould®-nozzle, pressure controlled –– •Relief valve for nozzle pressure control (standard from 350t) • •Wear resistant screw and barrel AK+ • •Barrel insulation • •Screw with mixing section or barrier section • •Hoppermagnet • •Hopper loader UNIFEED A1 (till SPE1330) • •
Safety gate
Operating safety gate at the rear side • •Front side gate safety system for manual part removal • •
E S
Pneumatic safety gate at the operator side • •Initiate next cycle by closing safety gate in semi-auto operation • •Safety gate clearance operator side/rear side extended • •Safety gate rear side lowered at the top of the upper tiebar • •
Cooling and conditioning
Additional flow controller with temperature gauges • •Shut-off valve for cooling water battery • •Blow out valve for cooling water battery • •Hosting of cooling circuits on the fixed platen for the moving platen • •
Electrical components
Temperature control zone for hot runner • •Non-contact stroke transducers (standard from 350t) –– •Special voltage • •Control cabinet cooler • •Closed loop temperature control of mould • •Additional socket • •Fuse protection for sockets • •Power factor correction and active power optimization –– •Interface for handling equipment • •Energy consumption analysis –– •Integrated Tandemmould –– •Switch over to holding pressure by cavity or melt pressure • •Switch over to holding pressure by external signal • •Purging program through the open mold • •Melt cushion control –– •Audible alarm • •Analog temperature control interface • •Temperature control interface digital, serial 20mA TTY protocol –– •CAN-Bus-interface for mold conditioner as per EUROMAP 66-2 –– •CAN-Bus-interface for hot runner as per EUROMAP 66-2 –– •Interface for Airmould® mobile/integrated as well as EUROMAP 62 –– •
Interface for robots as per EUROMAP 67 • •Adaptor from EUROMAP 67 to EUROMAP 12 • •Interface for conveyor belt • •Scale interface • •Host computer interface/PDA (EUROMAP 63) –– •Relays contact parallel to plasticizing • •Machine fault (potential-free contact) • •BNC connectors for injection process analysis –– •Remote diagnostics via network • •Interface for common data storage with Battenfeld robot –– •Interface for vacuum pump –– •Second injection data setting for automatic start up –– •
Accessories
Special paint • •Tool kit • •Touch-up paint • •Levelling pads • •USB stick for data storage • •
THE POWER to SUCCEED
Battenfeld Kunststoffmaschinen Gesellschaft m.b.H.Wiener Neustädter Strasse 81 · 2542 Kottingbrunn · AustriaTel. +43 2252 404-0 · Fax +43 2252 [email protected]
www.battenfeld-imt.com M/3
/
/T
M 1
00t–
450
t20
00/1
0/07
(TS
/10/
07)·
Nar
/Kay
Sub
ject
to c
hang
eGB