+ All Categories
Home > Documents > 101-0005 (2004)

101-0005 (2004)

Date post: 22-Nov-2014
Category:
Upload: masood46
View: 806 times
Download: 13 times
Share this document with a friend
17
Standard STD 101-0005 Volvo Group Established October 2004 Version 2 Page 1(17) The English language version is the original and the reference in case of dispute. Den engelska språkversionen är originalversion och skall åberopas i händelse av tvist. BASIC RULES FOR REPRESENTATION GRUNDREGLER FÖR REPRESENTATION Symbols, designations and general drawing methods Symboler, beteckningar och allmänt ritsätt Orientation Orientering This standard is based on Volvo corporate standard STD 5023,501, which it replaces in applicable parts. Denna standard baserar sig på Volvo koncern- standard STD 5023,501 som den ersätter i tillämpliga delar. To completely cover the scope of STD 5023,501, this standard shall be referred to together with STD 5023,503 in accordance with the description in section 12.1. För att fullständigt täcka omfattningen av STD 5023,501 skall denna standard vara hänvisad till tillsammans med STD 5023,503 i enlighet med beskrivning i avsnitt 12.1. This version differs from version 1 in that the following changes have been made: Denna utgåva skiljer sig från utgåva 1 genom att följande ändringar har genomförts: a text has been added to section 1 saying that a standard specified on drawing and being in conflict with any standard referred to in STD 101-0005, shall have priority. en text har tillkommit i avsnitt 1 om att en standard som angivits på en ritning och som strider mot någon av de standarder som hänvisas till i STD 101-0005, skall ha prioritet the title of section 7.2 has been changed to “Geometrical tolerances and datums” rubriken på avsnitt 7.2 har ändrats till ”Form- och lägetoleranser samt referenser” examples showing that a toleranced profile characteristic applies all around a workpiece and the designation of a common tolerance zone to several features have been added to section 7.2 exempel på att en toleranssatt profilegenskap gäller runtom ett arbetsstycke och beteckning av att ett gemensamt toleransområde för flera element har tillkommit i avsnitt 7.2 examples illustrating datum targets for coordinate systems in accordance with a new standard, STD 101-0003, have been added to section 7.2 exempel som illustrerar lokala referenser för koordinatsystem i enlighet med en ny standard, STD 101-0003, har tillkommit i avsnitt 7.2 a new section 8, “Critical characteristics of design parts” has been inserted and due to that, the subsequent section numbers have been changed. ett nytt avsnitt 8 ”Kritiska egenskaper för konstru- erade artiklar” har tillkommit och beroende på detta har de efterföljande avsnittsnumren ändrats. Contents Innehåll 1 Scope and field of application 1 Omfattning och tillämpning 2 General rules on drawing data 2 Allmänna regler om ritningsdata 3 Projection methods and cutting planes 3 Projektionsmetoder och snittplan 4 Lines, points, surfaces and markings 4 Linjer, punkter, ytor och markeringar 5 Simplified representation of machine elements 5 Förenklad ritning av maskinelement 6 Dimensioning 6 Måttsättning 7 Tolerances 7 Toleranser 8 Critical characteristics of design parts 8 Kritiska egenskaper för konstruerade artiklar 9 Marking of parts 9 Artikelmärkning 10 Hardness and case depth 10 Hårdhet och härddjup 11 Information in the drawing sheet blocks 11 Uppgifter i fälten på ritningsblanketten 12 Reference to this standard 12 Hänvisning till denna standard
Transcript
Page 1: 101-0005 (2004)

Standard STD 101-0005 Volvo Group

Established October 2004 Version 2 Page 1(17)

The English language version is the original and the reference in case of dispute.

Den engelska språkversionen är originalversion och skall åberopas i händelse av tvist.

BASIC RULES FOR REPRESENTATION GRUNDREGLER FÖR REPRESENTATION

Symbols, designations and general drawing methods

Symboler, beteckningar och allmänt ritsätt

Orientation Orientering This standard is based on Volvo corporate standard STD 5023,501, which it replaces in applicable parts.

Denna standard baserar sig på Volvo koncern-standard STD 5023,501 som den ersätter i tillämpliga delar.

To completely cover the scope of STD 5023,501, this standard shall be referred to together with STD 5023,503 in accordance with the description in section 12.1.

För att fullständigt täcka omfattningen av STD 5023,501 skall denna standard vara hänvisad till tillsammans med STD 5023,503 i enlighet med beskrivning i avsnitt 12.1.

This version differs from version 1 in that the following changes have been made:

Denna utgåva skiljer sig från utgåva 1 genom att följande ändringar har genomförts:

• a text has been added to section 1 saying that a standard specified on drawing and being in conflict with any standard referred to in STD 101-0005, shall have priority.

• en text har tillkommit i avsnitt 1 om att en standard som angivits på en ritning och som strider mot någon av de standarder som hänvisas till i STD 101-0005, skall ha prioritet

• the title of section 7.2 has been changed to “Geometrical tolerances and datums”

• rubriken på avsnitt 7.2 har ändrats till ”Form- och lägetoleranser samt referenser”

• examples showing that a toleranced profile characteristic applies all around a workpiece and the designation of a common tolerance zone to several features have been added to section 7.2

• exempel på att en toleranssatt profilegenskap gäller runtom ett arbetsstycke och beteckning av att ett gemensamt toleransområde för flera element har tillkommit i avsnitt 7.2

• examples illustrating datum targets for coordinate systems in accordance with a new standard, STD 101-0003, have been added to section 7.2

• exempel som illustrerar lokala referenser för koordinatsystem i enlighet med en ny standard, STD 101-0003, har tillkommit i avsnitt 7.2

• a new section 8, “Critical characteristics of design parts” has been inserted and due to that, the subsequent section numbers have been changed.

• ett nytt avsnitt 8 ”Kritiska egenskaper för konstru-erade artiklar” har tillkommit och beroende på detta har de efterföljande avsnittsnumren ändrats.

Contents Innehåll 1 Scope and field of application 1 Omfattning och tillämpning 2 General rules on drawing data 2 Allmänna regler om ritningsdata 3 Projection methods and cutting planes 3 Projektionsmetoder och snittplan 4 Lines, points, surfaces and markings 4 Linjer, punkter, ytor och markeringar 5 Simplified representation of machine elements 5 Förenklad ritning av maskinelement 6 Dimensioning 6 Måttsättning 7 Tolerances 7 Toleranser 8 Critical characteristics of design parts 8 Kritiska egenskaper för konstruerade artiklar 9 Marking of parts 9 Artikelmärkning 10 Hardness and case depth 10 Hårdhet och härddjup 11 Information in the drawing sheet blocks 11 Uppgifter i fälten på ritningsblanketten 12 Reference to this standard 12 Hänvisning till denna standard

Page 2: 101-0005 (2004)

Standard STD 101-0005 Volvo Group

Version 2 Page 2

1 Scope and field of application 1 Omfattning och tillämpning This standard contains graphic symbols, designations of, e.g. tolerances, hardness and case depth as well as general examples of drawing methods used on drawings produced within the Volvo Group or at the request of some individual company within the Volvo Group. The standard refers also to those Volvo Group common standards and ISO standards that give a complete definition of the representations shown.

Denna standard innehåller grafiska symboler, be-teckningar av exempelvis toleranser, hårdhet och härddjup samt generella exempel på ritsätt vilka används på ritningar som produceras inom Volvo-koncernen eller på uppdrag av något enskilt koncern-företag. Standarden hänvisar vidare till de Volvo-gemensamma standarder eller ISO-standarder som ger en fullständig definition av visade angivelser.

In certain cases, the specific drawing methods are established by this standard only.

I vissa fall är de specifika ritsätten endast fastställda genom denna standard.

In section 2 with sub-sections, a number of basic and general rules concerning the interpretation of drawings are stated. In addition, general requirements for toleranced properties are specified.

I avsnitt 2 med underavsnitt anges ett antal allmänna och grundläggande regler rörande tolkning av ritningar. Vidare specificeras allmänna krav för toleranssatta egenskaper.

By referring to this standard on drawings: Genom hänvisning till denna standard på ritning:

− the requirements specified in the standards that are indicated under the heading "Established by standard" in the following sections apply

− gäller krav enligt de standarder som anges under rubriken "Fastställd i standard" i de följande avsnitten

− it is possible to interpret the indications that the standard gives examples of.

− är det möjligt att tolka de angivelser som standar-den ger exempel på.

In those cases the drawing method used is not exemplified in this standard, reference to the standard applied shall always be given on the relevant drawing.

Där använd ritningsangivelse inte finns exemplifierad i denna standard, skall hänvisning till tillämpad standard alltid finnas på den aktuella ritningen.

If a drawing refers to a standard that conflicts with a standard within the body of STD 101-0005, then the standard noted on the drawing shall have priority.

Om en ritning refererar till en standard som är motstridig till en standard som åberopas i STD 101-0005 skall den standard som angivits på ritningen ha prioritet.

With the exception of those cases when this standard establishes a specific drawing method, the standard gives only a simplified explanation of the respective drawing indication. For a complete interpretation, the standards referred to in connection with the respective example always apply.

Med undantag för de fall där denna standard fast-lägger ett specifikt ritsätt ger standarden endast en förenklad förklaring av respektive ritningsangivelse. För fullständig tolkning gäller alltid de standarder vilka hänvisas till i anslutning till respektive exempel.

In case of any discrepancy between the indications given in this standard and the standards referred to for full interpretation, the latter always apply.

Vid eventuella skiljaktigheter mellan angivelser i den-na standard och de standarder som angetts för deras tolkning, gäller alltid de senare.

2 General rules on drawing data 2 Allmänna regler om ritningsdata Unless otherwise stated on the drawing or in the associ-ated document, dimensions are given in millimetres.

Om inget annat angivits på ritning eller i annat tillhö-rande dokument är måttuppgifter uttryckta i millimeter.

Unless otherwise indicated, generally or for a single piece of information, the technical documentation represents the object in its finished condition.

Om inget annat angivits, generellt eller för enskild uppgift, återger det tekniska underlaget objektet i sitt färdiga utförande.

The only exception from this rule is surface coated M-threads where the tolerance applies before any surface coating.

Enda undantaget från denna regel är M-gängor där toleransen gäller före eventuell ytbeläggning.

Page 3: 101-0005 (2004)

Standard STD 101-0005 Volvo Group

Version 2 Page 3

Scale Unless otherwise indicated generally on the drawing, main scale 1:1 has been applied. A locally indicated scale applies only to the view or section concerned.

Skala Om inget annat angivits generellt på ritningen, har huvudskala 1:1 tillämpats. En lokalt angiven skala gäller endast berörd vy eller berört snitt.

2.1 Principles for tolerance requirements

2.1 Principer för toleranskrav

For all toleranced properties on drawings and in associated documentation, STD 110-0001 Principles for tolerance requirements applies.

För alla toleranssatta egenskaper på ritning och i tillhörande dokumentation gäller STD 110-0001 Principer för toleranskrav.

3 Projection methods and cutting planes

3 Projektionsmetoder och snittplan

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

Principle / Princip

C

B

D

A

The arrow method. Layout of views according to the reference arrow method/ Pilmetoden. Vyplacering enligt metod med riktningspilar

ISO 128-30:2001

1

Method E. First angle projection method/ Metod E. Första kvadrantens projektions- metod

ISO 128-30:2001

Method A. Third angle projection method/ Metod A. Tredje kvadrantens projektions- metod

ISO 128-30:2001

Drawing and dimensioning in axonometric representation/ Ritning och måttsättning i axonometrisk representation

STD 101-0002

Page 4: 101-0005 (2004)

Standard STD 101-0005 Volvo Group

Version 2 Page 4

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

A

A

Indication of cutting plane/ Markering av snittplan

ISO 128-40:2001

4 Lines, points, surfaces and markings

4 Linjer, punkter, ytor och markeringar

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

General use and meaning of lines/ Linjers allmänna användning och betydelse

ISO 128-24:1999

Partial view of a symmetrical object. Two alternative methods of presentation/ Delvy av symmetriskt objekt. Två alternativa ritsätt

ISO 128-24:1999

Interrupted views. Two alternative methods of presentation/ Brutna vyer. Två alternativa ritsätt

ISO 128-24:1999

Outline before forming (in this case before bending)/ Kontur före bearbetning (i detta fall före bock-ning)

ISO 128-24:1999

Page 5: 101-0005 (2004)

Standard STD 101-0005 Volvo Group

Version 2 Page 5

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

Indication of outline of an adjacent part/ Markering av kontur för intilliggande objekt

ISO 128-24:1999

Indication of trajectories and alternative or ex-treme positions for movable parts/ Markering av bana för rörelse och alternativt eller extremt läge för rörlig del

ISO 128-24:1999

Indication of square surfaces and ends/ Markering av fyrkantiga ytor och ändar

ISO 128-24:1999

Indication of fluid in section/ Markering av vätska i snitt

Established by this standard/ Fastställd genom denna standard

5 Simplified representation of machine elements

5 Förenklad ritning av maskin-element

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

Representation of screw threads/ Ritning av gängor ← External visible screw threads/ Utvändiga synliga gängor

ISO 6410-1:1993

← Internal hidden screw threads/ Invändiga skymda gängor

Page 6: 101-0005 (2004)

Standard STD 101-0005 Volvo Group

Version 2 Page 6

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

← Section through internal screw threads/ Snitt genom invändiga gängor

ISO 6410-1:1993

Representation of gears / Ritning av kuggar

ISO 2203:1973

Symbols for gear type and direction/ Symboler för kuggtyp och riktning ← Helical to the right and to the left/ Snedkugg höger och vänster ← Double helical / Dubbel snedkugg ← Spiral / Bågkugg

Representation of splines and serrations/ Ritning av splines och serrationer Symbol for / Symbol för: ← Straight-sided splines/ Splines med rak profil ← Involute splines and serrations/ Evolventsplines och serrationer

ISO 6413:1988

A) B) C)

General simplified representation of dynamic seals/ Allmänt förenklad ritning av dynamiska tätningar: A) Sealing direction of no importance/ Tätningsriktning saknar betydelse B) Sealing direction (in the direction of the arrow)/ Tätningsriktning (i pilens riktning) C) Exact contour shown / Verklig kontur visad

ISO 9222-1:1989

Page 7: 101-0005 (2004)

Standard STD 101-0005 Volvo Group

Version 2 Page 7

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

Detailed simplified representation of lip type seals (radial seals)/ Detaljerad förenklad ritning av radialtätningar: ← Rotary shaft seal without dust lip/ Tätning utan dammtunga för roterande axel

ISO 9222-2:1989

← Seal without dust lip for stationary shaft and rotary housing/ Tätning utan dammtunga för stillastående axel och roterande hus

← Rotary shaft seal with dust lip/ Tätning med dammtunga för roterande axel

← Rotary shaft seal with dust lip (double- acting)/ Tätning med dammtunga för roterande axel (dubbelverkande)

Detailed simplified representation of lip type seals (radial seals)/ Detaljerad förenklad ritning av radialtätningar: ← Seal with dust lip for stationary shaft and rotary housing/ Tätning med dammtunga för stillastående axel och roterande hus

ISO 9222-2:1989

Detailed simplified representation of axial seals/ Detaljerad förenklad ritning av axialtätningar ← Rotary shaft axial seal/ Axialtätning för roterande axel

ISO 9222-2:1989

Page 8: 101-0005 (2004)

Standard STD 101-0005 Volvo Group

Version 2 Page 8

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

Detailed simplified representation of seals for reciprocating movements (piston rod seals)/ Detaljerad förenklad ritning av tätningar för fram- och återgående rörelser (kolvstångs-tätningar):

ISO 9222-2:1989

A) B) C) D)

A) U-cups / U-manschetter B) V packing sets / V-tätningssats C) V-rings / Hattmanschetter D) Wipers / Avstrykare

Detailed simplified representation of labyrinth seals/ Detaljerad förenklad ritning av labyrinttätningar

ISO 9222-2:1989

A) B)

Simplified representation of rolling bearings/ Förenklad ritning av rullningslager Normally drawn in accordance with A). B) shows an example of simplified representation showing the exact outline of the bearing/ Ritas normalt enligt A). B) visar exempel på förenklad ritning där lagrets verkliga kontur visas

ISO 8826-1:1989

Guide pin, guide hole, centre of gravity/ Styrpinne, styrhål, tyngdpunkt

Established by this standard/ Fastställd genom denna standard

6 Dimensioning 6 Måttsättning

6.1 General dimensioning 6.1 Måttsättning allmänt

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

65±0,5

35±0

,5

Dimensioning, general principles/ Måttsättning, allmänna regler

ISO 129:1985

60,5°±1,5°

Dimensioning of angular dimensions/ Måttsättning av vinkelmått

ISO 129:1985

Page 9: 101-0005 (2004)

Standard STD 101-0005 Volvo Group

Version 2 Page 9

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

(55) Indication of auxiliary dimensions/ Markering av hjälpmått

ISO 129:1985

50

Indication of arc dimensions/ Markering av bågmått

ISO 129:1985

Origin indication in superimposed running dimensioning/ Nollpunkt vid förenklad baslinjemåttsättning

ISO 129:1985

16

Framed dimensions / Inramade mått:

Theoretically exact dimensions when using geometrical tolerances/ Teoretiskt riktiga mått vid tillämpning av form- och lägetoleranser

STD 112-0003

Setting dimension, gauge dimension for production and inspection. These dimensions shall be considered as having no tolerances/ Inställningsmått, tolkmått för produktion och kontroll. Dessa mått betraktas som toleranslösa

Established by this standard/ Fastställd genom denna standard

F6

F11

Numbering of holes / Hålnumrering Holes designated by letters and figures where/ Hål betecknas med bokstäver och siffror där: T = view from above / vy uppifrån B = view from below / vy underifrån F = front view (principal view)/ vy framifrån (huvudvy) R = view from the rear / vy bakifrån RH = view from the right / vy från höger LH = view from the left / vy från vänster

STD 101-0004

6.2 Symbols in connection with dimensions

6.2 Symboler i samband med mått

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

∅ Diameter ISO 129:1985

R Radius / Radie ISO 129:1985

Square / Kvadrat ISO 129:1985

Page 10: 101-0005 (2004)

Standard STD 101-0005 Volvo Group

Version 2 Page 10

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

Oblong hole / Avlångt hål Established by this

standard/ Fastställd genom denna standard

Indication of taper / Angivelse av kona ISO 3040:1990

Rectangular shape / Rektangulär form Fastställd genom denna

standard/ Established by this standard

SR Spherical radius / Sfärisk radie ISO 129:1985

S∅ Spherical diameter / Sfärisk diameter ISO 129:1985 CL Centre line / Centrumlinje Established by this

standard/ Fastställd genom denna standard

x Number of equal elements, for example 5x10 for five times the dimension 10/ Antalet lika element, exempelvis 5x10 för fem gånger måttet 10

ISO 129:1985

6.3 Marking of requirements 6.3 Markering av krav

Drawing method Ritsätt

Explanation Betydelse

Established by standardFastställd i standard

A) B)

Indication of a partial requirement, for example hardening/ Markering av partiellt krav, exempelvis härdning

When the extension of the requirement is of no importance or when it is obvious, the dimensioning can be excluded, see figure A) / Är kravets utsträckning oväsentlig eller självklar utelämnas måttsättning, se figur A)

When needed, the special requirement shall be dimensioned, see figure B)/ Vid behov måttsätts det speciella kravet, se figur B)

ISO 129:1985

Page 11: 101-0005 (2004)

Standard STD 101-0005 Volvo Group

Version 2 Page 11

7 Tolerances 7 Toleranser

7.1 Dimensional tolerances 7.1 Dimensionstoleranser

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

± 0,5 Tolerance for linear dimension/ Tolerans för linjärt mått

STD 110-0001

+ 1,5° 0

Tolerance for angular dimension (fraction of degree in decimals)/ Tolerans för vinkelmått (del av grad i decimaler)

STD 110-0001

E Envelope requirement / Enveloppkrav STD 110-0001

7.2 Geometrical tolerances and datums 7.2 Form- och lägetoleranser samt referenser

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

Ø0,5 A

Tolerance frame with example of information/ Toleransrektangel med exempel på uppgifter:

← Datum / Referens

← Tolerance value / Toleransvärde

← Toleranced characteristic/ Toleranssatt egenskap

STD 112-0003

Straightness / Rakhet STD 112-0003

Flatness / Planhet STD 112-0003

Roundness / Rundhet STD 112-0003

Cylindricity / Cylindricitet STD 112-0003

Profile of any line / Profilform

Position of any profile / Profilläge (with datum feature / med referenselement)

STD 112-0003

Page 12: 101-0005 (2004)

Standard STD 101-0005 Volvo Group

Version 2 Page 12

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

Profile of any surface / Ytform

Position of any surface / Ytläge (with datum feature / med referenselement)

STD 112-0003

Position / Lägeriktighet STD 112-0003

Concentricity, coaxiality/ Koncentricitet, koaxialitet

STD 112-0003

Symmetry / Symmetri STD 112-0003

Parallelism / Parallellitet STD 112-0003

Perpendicularity / Vinkelräthet STD 112-0003

Angularity / Vinkelriktighet STD 112-0003

Run-out / Kast STD 112-0003

Total run-out / Totalkast STD 112-0003

Toleranced profile characteristic applies all around the outline of the workpiece/ Toleranssatt profilegenskap gäller konturen runtom arbetsstycket

STD 112-0003

Ø 0,2 CZ

CZ = Common Zone A single tolerance zone that applies to several separate features/ CZ = gemensamt toleransområde Ett enskilt toleransområde som gäller för flera separata element

STD 112-0003

P

Projected tolerance zone/ Utflyttat toleransområde

STD 112-0003

M

Maximum material principle / Måttjämkning STD 112-0001

L

Least material requirement/ Min materialkrav

ISO 2692:1988/Amd 1:1992

Page 13: 101-0005 (2004)

Standard STD 101-0005 Volvo Group

Version 2 Page 13

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

F

Free state condition/ Fritt tillstånd

ISO 10579:1993

Indication of measuring principles/ Angivelse av mätprinciper

Example: measuring principles 2 and 3 Exempel: mätprinciper 2 och 3

STD 112-0004

A

20x20

MP 2

A

B

MP 3

Indication of datum with datum letter/ Angivelse av referens med referensbokstav

STD 112-0002

Indication of datum without datum letter/ Angivelse av referens utan referensbokstav

STD 112-0002

1

Datum target / Lokal referens

Example: datum target point A1/ Exempel: lokal referenspunkt A1

STD 112-0002

B1

Example: datum target line B1/ Exempel: lokal referenslinje B1

18

Example: datum target area A1, ∅ 8 Exempel: lokal referensarea A1, ∅ 8

2

Example: datum target area B2, 20x20 Exempel: lokal referensarea B2, 20x20

Page 14: 101-0005 (2004)

Standard STD 101-0005 Volvo Group

Version 2 Page 14

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

X5Ø25

Datum target for coordinate system (only letters X, Y and Z designating coordinate direction are used)/ Lokal referens för koordinatsystem (endast bokstäverna X, Y och Z, som betecknar koordinatriktning, används)/

Example: datum target area X5, ∅ 25 Exempel: lokal referensarea X5, ∅ 25

STD 101-0003

aY2

Datum target for interface system in coordinate system (interface systems are identified with a small letter preceding the coordinate letter)/ Lokal referens för interface-system i koordinat-system (interface-system identifieras med en liten bokstav före koordinatbokstav)/

Example: datum target point aY2/ Exempel: lokal referenspunkt aY2

STD 101-0003

8 Critical characteristics of design parts

8 Kritiska egenskaper för konstruerade artiklar

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

[1] Criticality 1/ Allvarlighetsgrad 1

STD 105-0001

[2] Criticality 2/ Allvarlighetsgrad 2

STD 105-0001

[3] Criticality 3/ Allvarlighetsgrad 3

STD 105-0001

9 Marking of parts 9 Artikelmärkning

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

Requirement for marking of parts Krav på artikelmärkning

STD 103-0007

Page 15: 101-0005 (2004)

Standard STD 101-0005 Volvo Group

Version 2 Page 15

10 Hardness and case depth 10 Hårdhet och härddjup

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

350 HBS

Designation of Brinell hardness/ Beteckning för Brinellhårdhet:

Brinell hardness 350 determined with a steel ball (previously denoted HB). HBW denotes the Brinell hardness determined with a hard metal ball/ Brinellhårdhet 350 bestämd med stålkula (tidigare betecknad HB). HBW betecknar brinellhårdhet bestämd med hårdmetallkula

STD 323-0001

600 HBW 5/750/20

When needed, the designation is supple-mented with/ Vid behov kompletteras beteckningen med:

← Ball diameter (mm) / Kuldiameter (mm)

← Mass (kg) that yields the test force/ Massa (kg) som åstadkommer provkraften

← Duration of test force application (s)/ Hålltid (s)

59 HRC

Designation of Rockwell hardness/ Beteckning för Rockwellhårdhet:

Rockwell hardness 59, measured on the Rockwell C-scale/ Rockwellhårdhet 59 bestämd enligt Rockwellskala C

STD 323-0002

640 HV

Designation of Vickers hardness/ Beteckning för Vickershårdhet:

← Vickers hardness 640 / Vickershårdhet 640

STD 323-0003

640 HV 30/20

When needed, the designation is supple-mented with/ Vid behov kompletteras beteckningen med: ← Mass (kg) that yields the test force/ Massa (kg) som åstadkommer provkraften ← Duration of test force application (s)/ Hålltid (s)

Page 16: 101-0005 (2004)

Standard STD 101-0005 Volvo Group

Version 2 Page 16

Drawing method Ritsätt

Explanation Betydelse

Established by standard Fastställd i standard

DC = 1,2 ± 0,3

Designation of case-hardened depth/ Beteckning för sätthärdningsdjup:

← Case-hardened depth 1,2±0,3/ Sätthärdningsdjup 1,2±0,3

STD 322-0002

+ 0,2 DC 650 = 0,4 - 0,1

Requirement for another hardness limit for the case-hardened depth than 550 HV shall be indicated as in the example below/ Krav på annan gräns för sätthärdningsdjupet än 550 HV anges enligt nedanstående exempel:

← Case-hardened depth 0,4+0,2/-0,1 at 650 HV/ Sätthärdningsdjup 0,4+0,2/-0,1 vid 650 HV

DI = 2 ± 1

Designation of induction-hardened depth/ Beteckning för induktionshärdningsdjup:

← Induction-hardened depth 2±1/ Induktionshärdningsdjup 2±1

STD 322-0001

DI 500 = 2 ± 1

Requirement for another hardness limit for the induction-hardened depth than 400 HV shall be indicated as in the example below/ Krav på annan gräns för induktions-härdningsdjupet än 400 HV anges enligt nedanstående exempel:

← Induction-hardened depth 2±1 vid 500 HV/ Induktionshärdningsdjup 2±1 at 500 HV

DNC = 0,3 MIN

Designation of nitrocarburizing depth/ Beteckning för nitrokarbureringsdjup:

← Nitrocarburizing depth 0,3 MIN/ Nitrokarbureringsdjup 0,3 MIN

STD 322-0004

DN = 0,4 ± 0,1

Designation of nitriding depth/ Beteckning för nitrerdjup:

← Nitrerdjup 0,4±0,1/ Nitriding depth 0,4±0,1

STD 322-0003

11 Information in the drawing sheet blocks

11 Uppgifter i fälten på ritnings-blanketten

For interpretation of information in the title and revision blocks of the drawing sheet with title block in accordance with figure 1, STD 910-0001 is referred to.

För tolkning av uppgifter i ritningsblankettens huvud- respektive ändringsfält på ritningsblanketter med huvudfält enligt figur 1, hänvisas till STD 910-0001.

Page 17: 101-0005 (2004)

Standard STD 101-0005 Volvo Group

Version 2 Page 17

The copying, distribution and utilization of this document as well as the communication of its contents to others without expressed authorization is prohibited. Offenders will be held liable for payment of damages. All rights reserved in the event of the grant of a patent, utility model or ornamental design registration.

Document title

Document type

Document No Issue Sheet No

Owner domain:Document prefix

Fig. 1 - The form exists in a number of versions with the same layout but with different company names Blanketten finns i ett antal versioner med samma layout men med olika företagsnamn

12 Reference to this standard 12 Hänvisning till denna standard For the application of this standard, a reference shall be given in the text block of the drawing in accordance with below.

Vid tillämpning av denna standard skall hänvisning ges genom not i ritningens skrivfält enligt nedan:

SYMBOLS, DESIGNATIONS AND GENERAL DRAWING METHODS STD 101-0005

12.1 Reference to this standard in combination with STD 5023,503

12.1 Hänvisning till denna standard i kombination med STD 5023,503

When symbols, designations and general drawing methods according to this standard as well as those covered by standard STD 5023,503 apply, reference to both standards shall be given in the text block of the drawing in accordance with below.

Vid tillämpning av symboler, beteckningar och ritsätt i denna standard samt även de som täcks av standard STD 5023,503, skall hänvisning till båda dessa standarder ges genom not i ritningens skrivfält enligt nedan:

SYMBOLS, DESIGNATIONS AND GENERAL DRAWING METHODS STD 101-0005 AND STD 5023,503


Recommended