101_US-EN

Concrete Restoration Systems

2

Introduction

Our corporate philosophy

Through quality management practices, MAPEI seeks to bring value

to our customers, leadership and innovation to our market, excellence

to our manufacturing practices, satisfaction to our employees and

colleagues, and profitable growth to our company.

R&D emphasis

MAPEI’s innovative new products come from continuous research and

development. More than 12% of MAPEI’s employees work to research

and formulate new, technologically superior products for our customers.

To stay on the cutting edge of innovation, MAPEI reinvests 5% of its

annual sales revenue into research & development of new products.

“Best-Backed” products

MAPEI’s Best-Backed™ Warranty Program assures distributors, contractors and design professionals that MAPEI stands

behind its products with the industry’s best warranty terms. This confidence is passed on to the property owner during

the installation. Warranties are given for individual products as well as complete installation systems.

Knowledgeable sales force

MAPEI’s sales force is dedicated to providing knowledge locally for every

customer. Sales representatives regularly update their technical knowledge

with training at the MAPEI Technical Institute (MTI) branches in the USA

and Canada.

“Green” focus

MAPEI leads the industry with the largest selection of eco-friendly products available. The

company’s environmental commitment is demonstrated in its large selection of “green

innovation” products, which help to contribute valuable points toward LEED-

certified projects. MAPEI directs 70% of its R&D efforts to formulating ecologically

sustainable solutions.

MAPEI’s legacy began in 1937.

3

Table of ContentsQuick-Reference Charts

4 Primers for Self-Leveling Materials

5 Self-Leveling Underlayments

Product Information

6 Index to Technology Logos

6-9 Self-Leveling Underlayments

9 Decorative Topping

10-11 Primers for Self-Leveling

11-12 Moisture Reduction

12-13 Patching and Skimcoating

Compounds

13-14 Screed Mortars

14-17 Concrete Repair Mortars

18-21 FRP Composite Systems

21-22 Construction Grouts

23 Exterior Finishing

24-27 Waterproofing

28 Repair Epoxies

29 Admixtures

30 Corrosion Protection

30-31 Coatings and Sealers

32-33 Sealants and Joint Fillers

Other

34 MAPEI Technical Institute

Intro

ductio

nod

Table

of C

onte

ntsTechnical expertise

MAPEI’s Technical Services team supports individual

customers by helping to plan work, troubleshooting

problems, reviewing product claims and testing materials

for quality. In addition to the staff at headquarters,

Technical Service Regional Consultants are located in the

field to assist customers in person. The team also supplies

customer training at seven MAPEI Technical Institute (MTI)

branches located in Deerfield Beach, Florida; Garland,

Texas; San Bernardino, California; Dalton, Georgia; Laval,

Quebec; Delta, British Columbia; and Brampton, Ontario.

Customer-oriented service

The Customer Service staff is the first point of contact

for many MAPEI customers. Superior service is available

throughout the Americas by calling 1-800-42-MAPEI

(1-800-426-2734), a number that automatically connects

callers from Canada to Venezuela with their nearest facility.

Quick-Reference Charts

4

Primer L™

Advanced-technology acrylic latex primer for concrete

Primer WE ™

Water-based epoxy primer

Primer T ™

All-purpose primer for self-leveling underlayments

Primer E ™

High-performance, 100%-solids epoxy

primer

Primer CE ™

Ultra low-viscosity,consolidating epoxy

primer

SU

BS

TR

AT

ES

Absorbent concrete Yes No Yes Yes Yes

Nonabsorbent concrete No Yes Yes Yes Yes

Exterior-grade plywood No Yes Yes Yes Yes

Ceramic No Yes Yes Yes Yes

VCT No Yes Yes Yes Yes

Terrazzo No No Yes Yes Yes

Steel No No No Yes Yes

Use with Planiseal ™ EMB moisture-reduction

barrierNo Yes No Yes Yes

Approximate coverage

600 to 800 sq. ft. per U.S. gal.

(55,7 to 74,3 m2 per 3,79 L) (per application; many substrates

require multiple applications)


(18,6 to 37,2 m2 per 3,79 L)


(18,6 to 37,2 m2 per 3,79 L)


(13,9 to 18,6 m2 per 3,79 L)


(7,43 to 13,0 m2 per 3,79 L)

Cure time at 73° F (23°C)

3 hours > 2 hours 2 to 5 hours 6 to 7 hours 5 to 6 hours

Window to install self-leveling materials

3 to 18 hours 2 to 18 hours Up to 24 hours Next day Next day

Primers for Self-Leveling Materials

While the primers listed are suitable on the substrates indicated, many variables impact final performance. Review the specific primers’ Technical Data Sheets

for specific instructions. On large projects, consult with a MAPEI technical consultant to ensure that the best primer is selected for your application.

For all projects where Ultraplan® M20 Plus or Ultratop ® is used as a topping, use Primer L or apply Primer E with the sand broadcast method.

In unique cases, Primer WE may be appropriate.

5

Prim

ers fo

r Self-Le

velin

g

Mate

rials

Self-Le

velin

g U

nderla

yments

Reduced-Surface-Preparation

Self-Levelers

TraditionalSelf-Levelers

EngineeredGypsum

Novoplan® EasyEasy-preparation,

self-leveling underlayment

Ultraplan® EasyHigh-performance, easy-preparation,


Novoplan ® 2Professional, self-leveling

underlayment

Ultraplan ® 1 PlusHigh-performance,quick-setting, self-

leveling underlayment

Ultraplan ® M20 Plus

Quick-setting, high-compressive-strength

underlayment

Planitex™ SLSelf-leveling

underlayment for gypsum and wood

substrates

Planitex™ SL 35Engineered gypsum


Over concrete, ceramic,

VCT and terrazzoYes Yes Yes Yes Yes Yes Yes

Interior Yes Yes Yes Yes Yes Yes Yes

Substrate profile Prepared/primed Prepared/primed Prepared/primed Prepared/primed Prepared/primed Prepared/primed Prepared/primed

Application range1/8" to 1"

(3 mm to 2,5 cm)Featheredge to 2"

(5 cm)1/8” to 1”

(3 mm to 2,5 cm)Featheredge to 1.5"

(3,8 cm)1/8” to 2”

(3 mm to 5 cm)Featheredge to 1.25"

(3,2 cm)1/4" to 3"

(6 mm to 7,5 cm)

Approximate coverage

24 sq. ft. (2,23 m2) per bag

at 1/4" (6 mm)

24 sq. ft. (2,23 m2) per bag

at 1/4" (6 mm)

24 sq. ft. (2,23 m2) per bag

at 1/4" (6 mm)

24 sq. ft. (2,23 m2) per bag

at 1/4" (6 mm)

24 sq. ft. (2,23 m2) per bag

at 1/4” (6 mm)

24 sq. ft. (2,23 m2) per bag

at 1/4" (6 mm)

24 sq. ft. (2,23 m2) per bag

at 1/4" (6 mm)

Working time (73°F [23°C])

10 minutes 15 minutes 10 minutes 15 minutes 15 minutes 15 minutes 15 minutes

Cure time before installing

ceramic tile (73°F [23°C])

12 hours 3 hours 24 hours 3 hours 4 hours 3 days* 3 to 5 days*

Cure time before installing

resilient or wood flooring

(73°F [23°C])

36 hours 24 hours 72 hours 24 hours 16 to 24 hours 5 to 7 days* 7 to 10 days*

Compressive strength

(ASTM C109)

1 day = > 1,800 psi (12,4 MPa);

28 days = > 4,000 psi (27,6 MPa)

1 day = > 2,000 psi (13,8 MPa);

28 days = > 4,100 psi (28,3 MPa)

1 day = > 1,250 psi (8,62 MPa);

28 days = > 4,200 psi (29,0 MPa)

1 day = > 2,000 psi (13,8 MPa);

28 days = > 4,150 psi (28,6 MPa)

1 day = > 2,800 psi (19,3 MPa);

28 days = > 5,000 psi (34,5 MPa)

1 day = > 1,800 psi (12,4 MPa);

28 days = > 4,000 psi (27,6 MPa)

1 day = > 1,000 psi (6,90 MPa);

28 days = > 3,600 psi (24,8 MPa)

Self-Leveling Underlayments

* Refer to Technical Data Sheet for testing procedure to determine readiness for floor covering.

Products developed with MAPEI’s “green innovation” are LEED-compliant, helping to contribute valuable points toward LEED-certified projects.

Corrosion Inhibitor Enhanced repair mortars feature proprietary additives that fortify the passivation layer on embedded reinforcing steel, enhancing its resistance to corrosion.

CORROSIONINHIBITORCORROSIONINHIBITOR

E N H A N C E D

™

MAPEI’s FastTrack Ready products reduce the required steps of an installation and/or perform more quickly than current technology.

TM

6


Engineered Gypsum Self-Leveling

Underlayment

For Professional Use

Planitex SL 35 is a gypsum-based, self-leveling

underlayment with an exceptionally smooth, hard

surface for use in dry interior residential and

commercial areas. Planitex SL 35 is designed for

application at depths of 1/4” to 3” (6 mm to 7,5

cm) and provides an excellent substrate for floor

coverings such as rubber, sheet vinyl and vinyl

composition tile (VCT). Planitex SL 35 can be

used to cover radiant or in-floor heating systems.

Its impressive compressive and flexural strengths

allow it to support light wheeled traffic and light

commercial activity.

Planitex™ SL 35Planitex™ SL

Self-Leveling Underlayment for Gypsum

and Wood Substrates

Planitex SL is a high-performance gypsum-based

self-leveler. It is a low-VOC floor-smoothing

compound for patching, skimming, smoothing and

leveling in dry interior residential or commercial

areas. Planitex SL is suitable under normal loading

in interiors from featheredge to 1-1/4” (3,2 cm).

Planitex SL provides a suitable substrate for floor

coverings such as rubber, sheet vinyl and vinyl

composition tile (VCT). Planitex SL can be used

to cover radiant or in-floor heating systems, and

features exceptional compressive and flexural

strengths so that it can support light wheeled traffic.

Product Code

Product Code

Packaging PackagingProductCode

PackagingProduct Packaging ProductCode

PackagingProduct Packaging

U.S./ 117450 Bag: 50 lbs. (22,7 kg) Canada


Product Code

Product Code

Packaging Packaging

Index toTechnologyLogos

® TM

Products featuring High-Hydrated Cement Technology (HCT™) offer high early strength, excellent workability, ultra fast curing, unmatched long-term durability and efflorescence-free curing.

MAPEI mortars with Easy Glide Technology offer extreme ease of application, yielding a buttery consistency that reduces fatigue during troweling.

7

Easy-Preparation, Self-Leveling

Underlayment

Novoplan Easy is a high-strength, self-leveling

cement-based underlayment and repair mix for

interior concrete and engineer-approved floors.

It typically requires only a clean, soundly bonded

substrate before application. Novoplan Easy

provides low installation costs and fast turnaround

on jobsites.

Novoplan® EasyNovoplan® 2

Professional Self-Leveling Underlayment

Novoplan 2 is a high-strength, self-leveling,


interior concrete and engineer-approved floors.

Novoplan 2 is suited for leveling, smoothing and

repairing interior floors before the installation of

floor coverings. Ceramic tile and natural stone

can be installed 24 hours after application. Floor

coverings – such as carpet, vinyl sheet goods, vinyl

tile, vinyl composition tile (VCT), homogenous

PVC, rubber and engineered wood plank – can be

installed 1 to 3 days after application, depending

upon thickness of application.

U.S. 17850000 Bag: 50 lbs. (22,7 kg)

CanadaCanada 1785000021 1785000021 Bag: 50 lbs. (22,7 kg)Bag: 50 lbs. (22,7 kg)

Product Code

Packaging

TM

Product Code

PackagingProductCode



Product Code

Packaging

Index to

Technolo

gy Lo

gos

Self-Le

velin

g U

nderla

yments

Novoplan® 1

Calcium-Aluminate-Based Self-Leveling

Underlayment

For installation by authorized MAPEI Pinnacle

installers only

Novoplan 1 is a self-leveling, calcium-aluminate-


leveling and smoothing interior concrete floors.

U.S./ 13350000 Bag: 50 lbs. (22,7 kg)Canada

Product Code

Packaging

TM

® TM

® TM

® TM

8

TM

High-Performance, Easy-Preparation,

Self-Leveling Underlayment

Ultraplan Easy is an HCT™ (High-Hydrated Cement

Technology)-based, quick-setting, self-leveling

underlayment that typically requires only a clean,

soundly bonded substrate before application.

Typically requiring reduced surface preparation,

Ultraplan Easy provides lower installation costs

and fast turnaround on jobsites. It features high

strength and is able to withstand light foot traffic

after 2 to 3 hours of installation.

Ultraplan® Easy


Product Code




Product Code

Packaging

Quick-Setting, High-Compressive-Strength

Underlayment

Ultraplan M20 is an HCT™ (High-Hydrated

Cement Technology) calcium-aluminate-based,

quick-setting, self-leveling, self-drying material.

It is specially formulated for the resurfacing

and construction of interior horizontal surfaces

as a high-compressive-strength underlayment

with maximum resistance to wheel tracking and

indentations experienced in softer underlayments.

Ultraplan M20 Plus is suitable for use as a

commercial wear topping in warehouse and

alternate industrial applications where an

exceptional flat and smooth concrete surface is

desired.

Ultraplan® M20 Plus

Product Code




Product Code

Packaging

TM

High-Performance, Quick-Setting,

Self-Leveling Underlayment

Ultraplan 1 Plus is an HCT™ (High-Hydrated

Cement Technology)-based, quick-setting, self-

leveling, self-drying underlayment and repair mix

for interior concrete and engineer-approved floors.

Ultraplan 1 Plus has high strength and is abrasion-

resistant, able to withstand light foot traffic after 2

to 3 hours and vehicular rubber-wheel traffic after

3 days.

Ultraplan® 1 Plus

TM

Product Code




Product Code

Packaging

® TM

® TM

® TM

9

Self-Le

velin

g U

nderla

yments

Decora

tive To

ppin

g

Decorative Topping

TM

Ultratop®

U.S./ 19350000 White Bag: 50 lbs. (22,7 kg)Canada 19852000 Natural Gray Bag: 50 lbs. (22,7 kg)

Product Code

PackagingColor

High-Performance, Quick-Setting,

Self-Leveling Concrete Topping

Ultratop is a self-leveling, self-drying topping,

based on High-Hydrated Cement Technology

(HCT™), which is specially formulated for fast-

track resurfacing and construction of interior

horizontal surfaces.

Synthetic Lath

Mapelath is a lightweight, noncorroding, alkali-

resistant synthetic lath used as a substitute for

traditional metal lath. It is lighter and easier to work

with.

Mapelath™

U.S./ 02702000 Roll: 27” x 75’ (68,6 cm x 22,9 m) Canada

Product Code

Packaging

Lightweight Aggregate Mixture


installers only

Mapelite is a mixture containing an engineered

aggregate that significantly reduces the weight

and extends the yield of installations when used

with specific MAPEI mortars and self-leveling

underlayments. Mapelite is precisely manufactured

from post-consumer waste and qualifies for the

highest LEED rating for use of recycled materials.

When used with specified MAPEI binders, Mapelite

features ease of mixing, excellent workability and

sound final performance, offering an industry-

leading lightweight installation. .

Mapelite™


Product Code

Packaging

® TM

10

Primer L™

Advanced-Technology Acrylic Latex Primer

for Concrete

Primer L is a concentrated, solvent-free

acrylic primer used before the installation of

underlayments and topping materials. It is green

for easy identification. Primer L improves the bond

between a properly prepared and profiled concrete

substrate, and self-leveling underlayment or

topping materials.

U.S./ 36068000 Pail: 5 U.S. gals. (18,9 L) Canada 36053000 Jug: 1 U.S. gal. (3,79 L)

Product Code

Packaging

Primers for Self-Leveling

High-Performance, 100%-Solids

Epoxy Primer

Primer E is a two-component, 100%-solids epoxy

primer and bonding agent designed for use with

MAPEI self-leveling underlayments and toppings.

Primer E is the most effective method for bonding

to nonporous, dense substrates before installing

self-leveling underlayments or toppings subject

to high stress. Primer E is highly recommended

for all installations of decorative toppings (such

as Ultratop®), which demand the highest degree

of crack resistance and surface finish. Primer E ’s

low viscosity makes installation fast and easy, and

provides excellent penetration into the substrate

and therefore tenacious bond.

Primer E™

Product Code



U.S./ 36564 Part A, Pail: 2.06 U.S. gals. (7,80 L) Canada 36553 Part B, Jug: 0.94 U.S. gal. (3,56 L)

Product Code

Packaging

Ultra Low-Viscosity, Consolidating

Epoxy Primer

Primer CE is an ultra low-viscosity, two-

component, 100%-solids surface-consolidating

epoxy primer. Primer CE effectively penetrates

and consolidates the surface of weak concrete

or gypsum substrates. Applied in a single-coat

application, Primer CE is designed to restore

structural integrity to friable substrates such as

weak gypsum-based underlayments or lightweight

concretes before the application of underlayments,

toppings or floor finishes. Once installed, Primer

CE is compatible with a wide number of primers

and adhesives typically used with flooring

installations, such as with tile, vinyl composition

tile (VCT), carpet, sheet vinyl, wood and other

floor-finishing products.

Primer CE™

U.S./ 36864 Part A, Pail: 2.2 U.S. gals. (8,33 L) Canada 36853 Part B, Jug: 0.8 U.S. gal. (3,03 L)

Product Code

Packaging

TM

11

Prim

ers fo

r Self-Le

velin

gM

oistu

re R

eductio

n

All-Purpose Primer for Self-Leveling

Underlayments

Primer T is a low-VOC, water-based acrylic primer

that enhances the performance and adhesion

of self-leveling underlayments (SLUs) on

nonabsorbent surfaces such as ceramic tile, vinyl

composition tile (VCT) and adhesive residue, as

well as profiled, absorbent surfaces. Suitable for

a wide variety of substrates, Primer T combines

excellent versatility with an easy, low-odor

application.

Primer T™

Product Code

Packaging

TM

ProductCode


U.S./ 36657 Jug: 2 U.S. gals. (7,57 L) Canada 36691 Jug: 1 U.S. qt. (946 mL)

Product Code

Packaging

Water-Based Epoxy Primer

Primer WE is a two-component, polymer-modified,

solvent-free water-based epoxy primer for

enhanced adhesion to nonporous substrates before

the application of MAPEI self-leveling materials.

When mixed, Primer WE is purple for easy

identification. It improves adhesion over smooth,

nonabsorbent and difficult-to-bond-to substrates

such as properly prepared ceramic tile, cement-

based terrazzo, old cutback adhesive residue and

approved plywood subfloors.

Primer WE™

Product Code

Packaging

U.S./ 45457000 Kit: 2 U.S. gals. (7,57 L) Canada 45468000 Part A, Pail: 5 U.S. gals. (18,9 L) 45568000 Part B, Pail: 5 U.S. gals. (18,9 L)

Premium Epoxy Moisture Barrier for

Concrete Substrates

Planiseal EMB is a high-performance,

100%-solids, two-part epoxy, one-coat moisture

barrier system for concrete slabs that exhibit

moisture vapor emission rates (MVERs) up to 25

lbs. per 1,000 sq. ft. (11,3 kg per 92,9 m2) per 24

hours and reduces transmission rates to less than 3

lbs. (1,36 kg). Planiseal EMB ’s unique formulation

penetrates into the concrete substrate while creating

a solid film layer on the surface for the ultimate

in moisture transmission reduction. Planiseal

EMB can also be used at different coverage rate,

depending on the level of moisture vapor emission

control required.

Planiseal™ EMB

TM

U.S./ 46257 Kit: 2 U.S. gals. (7,57 L) Canada

Product Code

Moisture Reduction

Packaging

TM

12

Patching and Skimcoating Compounds

High-Performance Cementitious

Skimcoating Compound

Mapecem FineFinish is a high-performance,

polymer-modified, fiber-reinforced cement-

based skimcoating and patching compound. Use

Mapecem FineFinish to skimcoat and smooth

minor surface variations or defects on a variety

of substrates. Mapecem FineFinish creates a

strong, durable surface ready for almost any floor

application. Its unique formulation mixes easily

at a 50% water-to-powder ratio for a smooth and

easy-to-apply patching compound. Rapid-set

Mapecem FineFinish allows for fast-track flooring

installations 30 to 60 minutes after application.

Mapecem® FineFinish


Product Code

Packaging

TM

Fast-Setting, Alkali-Resistant, Epoxy

Moisture-Reduction Barrier


installers only

Planiseal VS Fast is an alkali-resistant, two-

component, 100%-solids epoxy coating that

effectively stops moisture-related problems with

floor coverings. The fast cure time of Planiseal VS

Fast enables priming for subsequent installation of

self-leveling underlayments in as early as 4 hours

after placement, ensuring effective moisture vapor

treatment and fast, same-day turn-around. With

Planiseal VS Fast, moisture vapor emission rates

(MVERs) of up to 25 lbs. per 1,000 sq. ft. (11,3 kg

per 92,9 m2) per 24 hours are reduced to below the

limit of 3 lbs. per 1,000 sq. ft. (1,36 kg per 92,9 m2)

required for many types of finished flooring.

Planiseal™ VS Fast

U.S./ 46964 Part A, 1.97 U.S. gals. (7,46 L)Canada 46953 Part B, 1 U.S. gal. (3,79 L)

Product Code

Packaging

Moisture Reduction

Alkali-Resistant, Epoxy Moisture-Reduction

Barrier


installers only

Planiseal VS is an alkali-resistant, two-component,

100%-solids epoxy coating that effectively stops

moisture-related problems with floor coverings. In

all cases, moisture vapor emission rates (MVERs)

of up to 25 lbs. per 1,000 sq. ft. (11,3 kg per 92,9

m2) per 24 hours are reduced to below 3 lbs. per

1,000 sq. ft. (1,36 per 92,9 m2) required for many

types of finished flooring, when the designated

film-thickness is applied.

Applied in a single-coat application system,

Planiseal VS offers low viscosity with high-density

resins that effectively reduce MVER by penetrating

deep into the substrate and effecting consolidation

well beneath the surface.

Planiseal™ VS

U.S./ 46364 Part A, Pail: 2.20 U.S. gals. Canada (8,33 L) 46353 Part B, Jug: 0.8 U.S. gal. (3,03 L)

Product Code

Packaging

® TM

13

Moistu

re R

eductio

nP

atc

hin

g a

nd S

kim

coatin

g

Com

pounds

Smoothing and Finishing Compound for

Concrete Surfaces

Tilt Finish is a versatile, fast-setting, polymer-

modified material utilizing a propietary blend of

cements and extremely fine aggregate. Tilt Finish

is ideal for producing a smooth finish on concrete

surfaces including tilt wall, poured-in-place

concrete, masonry, pre-cast beams and columns.

Tilt Finish features extraordinary ease of placement,

with a variable water ratio, extended pot life and

outstanding workability. Light gray Tilt Finish can

be applied from featheredge, up to 1/2” (12 mm)

in confined areas. Ease of placement makes it ideal

for covering imperfections in concrete surfaces,

providing a uniform and light gray appearance, or

a smooth surface before painting or application of

coating.

Tilt Finish™

Ready-to-Use, Accelerated-Cure Screed

Topcem Premix is a ready-to-use mortar requiring

only the addition of water. Topcem Premix is

suitable in both bonded and unbonded, interior

and exterior applications. Topcem Premix has

an accelerated cure, allowing for installation of

ceramic flooring in 24 hours after placement,

and nonbreathable flooring systems in 48 hours.

Topcem Premix can easily be screeded or sloped,

and has the workability and working time of

conventional mortars but with a much faster curing

time. It is ideal for interior or exterior repairs

such as filling trenches, re-sloping balconies,

and forming screeds that may or may not receive

subsequent flooring installations.

Topcem™ Premix

Product Code

Product Code





U.S. 15750 Bag: 50 lbs. (22,7 kg)

Product Code

Product Code

Packaging Packaging

High-Performance, High-Flow

Concrete Patch

Mapecem Quickpatch is a versatile, fast-setting,

cementitious material used for the patching of

interior/exterior concrete surfaces including

concrete floors, driveways, sidewalks and concrete

pads. Mapecem Quickpatch features extraordinary

ease of placement, with a variable water ratio and

outstanding workability. Light gray Mapecem

Quickpatch can be applied from featheredge to

3” (7,5 cm) for ramping or filling. That makes it

ideal for restoring weathered, damaged concrete

surfaces to a uniform, superior-wearing and better-

than-new appearance. When used for horizontal

substrate repair before application of self-leveling

underlayments, Mapecem Quickpatch sets fast for

easy and cost-efficient repairs, minimizing jobsite

turnaround time.

Mapecem® Quickpatch

TM

U.S. 10510000 Bag: 10 lbs. (4,54 kg) 10525000 Bag: 25 lbs. (11,3 kg)

10550 Bag: 50 lbs. (22,7 kg)

Product Code

Packaging

CanadaCanada 10510000211051000021 Bag: 10 lbs. (4,54 kg)Bag 10 lbs (4 54 kg)10525000 Bag: 25 lbs. (11,3 kg)1055010550 Bag: 50 lbs (22 7 kg)Bag: 50 lbs. (22,7 kg)

CanadaCanada 157400001 40000 Bag: 40 lbs. (18,1 kg)Bag: 40 lbs. (18,1 kg)

TM

Screed Mortars

Scre

ed M

orta

rs

14

Concrete Repair Mortars

Full-Depth Repair Mortar

Planitop FD is a one-part, shrinkage-compensated,

cementitious, self-compacting flowable mortar for a

variety of structural repairs. Planitop FD contains a

corrosion inhibitor and is suited for form-and-pour

applications as well as flatwork repairs at depths

from 1/2” to 4” (12 mm to 10 cm) neat. Planitop FD

is pumpable and ideal for deep repairs that require

ease of placement and a rapid return to service.

Planitop® FD

TM


E N H A N C E D

™

Product Code



U.S./ 15050000 Bag: 50 U.S. lbs. (22,7 kg) Canada

Product Code

Packaging

Medium-build, two-component, fast-setting

mortar

Mapecem 202 is a two-component, shrinkage-

compensated, polymer-modified, fast-setting

cementitious mortar with a corrosion inhibitor.

Mapecem 202 contains silica fume and is intended

for the repair and topping of interior/exterior

horizontal concrete surfaces, where a durable,

high-strength and low permeability concrete is

required. Mapecem 202 is excellent for heavy-duty

industrial applications, including manufacturing

and warehouse floors, loading docks and tipping

floors for smelting metals, where fast drying is

required to allow pedestrian and rubber wheel

traffic within 4 hours.

Mapecem® 202

TM


E N H A N C E D

™

Product Code



U.S./ 0150025 Part A, Bag: 55 lbs. (24,9 kg) Canada 0150003 Part B, Jug: 0.71 U.S. gal. (2,69 L)

Product Code

Packaging

Screed Mortars

Medium-Build, One-Component,

Fast-Setting Mortar

Mapecem 102 is a one-component, shrinkage-

compensated, polymer-modified, fast-setting

cementitious mortar with corrosion inhibitor.

Mapecem 102 is intended for the renovation and

topping of interior/exterior horizontal concrete

surfaces, such as tunnels, bridges, overpasses,

factory floors, warehouse floors and loading

docks; new and existing concrete slabs; and the

construction of floating or monolithic toppings

where fast drying is required to allow traffic

within 4 hours.

Mapecem® 102

TM


E N H A N C E D

™

Product Code




Product Code

Packaging

® TM

® TM

15

One-Component, Extended-Working-Time,

Vertical, Horizontal and Overhead Repair

Mortar

Planitop XS is an extended-working-time variation

of Planitop X. Shrinkage-compensated, fiber-

reinforced and polymer-modified, Planitop XS

features Planitop X ’s outstanding workability and

corrosion inhibitor. Ideal for use in a wide variety

of vertical and overhead concrete repairs, Planitop

XS can be applied in thicknesses of featheredge

to 4” (10 cm) per lift. Planitop XS is engineered

with MAPEI’s Easy Glide Technology™ for ease

of application and is light gray to match existing

concrete surfaces.

Planitop® XS Planitop® 12

Vertical and Overhead, One-Component

Repair Mortar

Planitop 12 is a one-component, shrinkage-

compensated, cementitious, thixotropic mortar

intended for the renovation of vertical and overhead

concrete surfaces. Planitop 12 is fiber-reinforced

and contains silica fume as well as a corrosion

inhibitor.


E N H A N C E D

™

Product Code

Product Code




U.S./ 13050000 Bag: 50 lbs. (22,7 kg)Canada 13051000 Pail: 50 lbs. (22,7 kg)


Product Code

Product Code

Packaging Packaging

One-Component, Fast-Setting Horizontal,

Vertical and Overhead Repair Mortar

Planitop X is a one-component, fiber-reinforced,

shrinkage-compensated, fast-setting, polymer-

modified, high-build cementitious repair mortar

with a corrosion inhibitor. It is suited for all

interior/exterior vertical, overhead and horizontal

concrete applications, including precast/

prestressed, tilt-up, post-tensioned and cast-in-

place concrete. Planitop X can be applied from

featheredge to 4" (10 cm) per lift. Planitop X is

engineered to provide high early strength with ease

of application. Planitop X dries to a light gray color,

matching most concrete surfaces.

Planitop® X

TM


E N H A N C E D

™

U.S. 12850000 Bag: 50 lbs. (22,7 kg) 12850010 Bag: 10 lbs. (4,54 kg)

12851000 Pail: 50 lbs. (22,7 kg)

CanadaCanada 1285000012850000 Bag: 50 lbs. (22,7 kg)Bag 50 lbs (22 7 kg)1285001021 Bag: 10 lbs. (4,54 kg)1285100012851000 Pail: 50 lbs. (22,7 kg)Pail: 50 lbs. (22,7 kg)

Product Code

Packaging

Scre

ed M

orta

rsC

oncre

te R

epair M

orta

rs

® TM

TM


E N H A N C E D

™®

TM

16

Concrete Repair Mortars

Fast-Setting, High-Early-Strength Repair

Mortar

Planitop 18 is a one-component, high-early-

strength, fast-setting, cementitious repair mortar

with corrosion inhibitor. It is suited for all interior/

exterior horizontal concrete repairs, including

bridge-deck overlays, parking-garage floor repairs,

ramps and various horizontal DOT (Department of

Transportation) concrete repairs.

Planitop® 18

TM


E N H A N C E D

™

Product Code



U.S./ 17950000 Bag: 50 lbs. (22,7 kg)Canada 17951000 Pail: 50 lbs. (22,7 kg)

Product Code

Packaging

Form-and-Pour, One-Component

Repair Mortar

Planitop 15 is a one-component, shrinkage-

compensated, cementitious, fiber-reinforced, fluid

mortar. Planitop 15 contains a corrosion inhibitor

and is suited for form-and-pour applications where

high early strength and flowability are required.

Planitop® 15


E N H A N C E D

™

Product Code




Product Code

Packaging

Planitop® 12 SR

Sulfate-Resistant, Vertical, Overhead and

Horizontal Repair Mortar with Silica Fume

Planitop 12 SR is a sulfate-resistant, one-

component, shrinkage-compensated, cementitious

repair mortar. Planitop 12 SR is fiber-reinforced

and contains both silica fume and a corrosion

inhibitor, and is intended for the repair of vertical,

overhead and horizontal concrete surfaces. Planitop

12 SR is used in those areas with soils containing

high alkalinity, near seawater or where sulfate

groundwater is present, such as underground

structures, retaining walls, foundations, slabs on

grade, coal-fired power plants, sewage-treatment

plants and fertilizer plants. Planitop 12 SR can be

used between the temperatures of 45ºF and 95ºF

(7ºC and 35ºC).


E N H A N C E D

™

Product Code




Product Code

Packaging

® TM

17

Concre

te R

epair M

orta

rs

Two-Component, Flowable Repair Mortar

for Resurfacing Damaged Horizontal

Concrete

Planitop 25 is a two-component, shrinkage-

compensated, cementitious, flowable resurfacing

mortar with corrosion inhibitor. Once mixed, the

mortar is easily placed onto horizontal surfaces

in thicknesses of 1/4” to 1” (6 mm to 2,5 cm) per

coat. Planitop 25 contains a high concentration

of synthetic polymer, which produces a dense,

durable resurfacing mortar with outstanding

adhesion, flexural and compression strengths.

It also has very low permeability, offering high

resistance to freeze/thaw cycles and chloride

ion penetration. Planitop 25 is formulated for

demanding commercial and industrial repairs

involving heavy impact and high abrasion, such as

loading docks, parking garages, warehouse floors,

and areas subject to extreme traffic and dynamic

loads.

Planitop® 25

TM


E N H A N C E D

™

Product Code



U.S./ 17603000 Part A, Bag: 57.1 lbs. (25,9 kg)Canada 4024004 Part B, Jug: 1.05 U.S. gals. (3,97 L)

Product Code

Packaging

Vertical and Overhead Two-Component

Repair Mortar

Planitop 23 is a pre-proportioned, two-component,

fast-setting, polymer-modified, thixotropic,

cementitious fiber-reinforced mortar, with a

corrosion inhibitor. Planitop 23 is intended for

vertical and overhead repairs, and contains silica

fume to provide a durable, high-strength concrete

in these applications.

Planitop® 23


E N H A N C E D

™

Product Code



U.S./ 4023026 Part A, Bag: 57.3 lbs. (26 kg) Canada 4024004 Part B, Jug: 1.05 U.S. gals. (3,97 L)

Product Code

Packaging

Thin-Build, Two-Component

Rendering Mortar

Planitop 21 is a pre-proportioned, two-component,

polymer-modified cementitious mortar. It is used

for renovating and resurfacing interior/exterior

concrete structures such as galleries, tunnels,

bridges, overpasses, retaining walls, beams,

building facades and ceilings. Planitop 21 also is

used for treating concrete surface blemishes and

defects; filling honeycombs, voids and cavities;

and protecting concrete against pollutants and

acid rain.

Planitop 21 contains a high concentration of

synthetic polymer, which produces a repair mortar

having excellent adhesion, flexural strength,

compressive strength, water impermeability and

freeze/thaw resistance. Apply up to 1/4”

(6 mm) thick.

Planitop® 21

Product Code



U.S./ 17545000 Part A, Bag: 45.8 lbs. (20,8 kg)Canada 4024004 Part B, Jug: 1.05 U.S. gals. (3,97 L)

Product Code

Packaging

® TM

18

FRP Composite Systems

Uni-Directional Glass Fiber Fabric

MapeWrap G Uni-Ax is a uni-directional glass fiber

fabric suitable for repairing reinforced concrete,

wooden and masonry elements damaged by

physical-mechanical action, for the reinforcement

of load-bearing elements in buildings that have

been restructured for architectural reasons or

change of use, and for seismic strengthening of

structures in earthquake-risk areas. MapeWrap G

Uni-Ax can be placed using two different methods:

the “wet system” with the aid of a machine that

helps the impregnation process and the “dry

system” where the resin is hand-applied during

installation.

MapeWrap™ G Uni-Ax

Product Code



U.S./ 7303450 Roll: MapeWrap G Uni-Ax 900, Canada 23.6" x 164' (60 cm x 50 m)

Product Code

Packaging

Balanced, High-Strength, Bi-Directional

Carbon Fiber Fabric

MapeWrap C Bi-Ax is a bi-directional carbon fiber

fabric with balanced weight and having a high

modulus of elasticity and high tensile strength.

MapeWrap C Bi-Ax is suitable for repairing

concrete structures and for improving the flexural

and shear strength of reinforced concrete elements.

It is also used for the confinement of axial-loaded

elements (columns, bridge piers, chimneys)

subjected to compressive and bending stress,

and for seismic strengthening in earthquake

areas. MapeWrap C Bi-Ax is installed using the

“wet-layup” system where the fabric is saturated

immediately before placement and the “dry-layup”

system where the fabric is saturated during

application.

MapeWrap™ C Bi-Ax

Product Code



U.S./ 7305550 Roll: MapeWrap C Bi-Ax 230, Canada 15.75" x 164' (40 cm x 50 m)

Product Code

Packaging

MapeWrap™ Primer 1

Epoxy Primer Specifically Formulated for

the MapeWrap System

MapeWrap Primer 1 is a two-component, super-

fluid , solvent-free epoxy resin , formulated

for the consolidation and priming of concrete,

reinforced concrete, or masonry surfaces before

bonding MapeWrap fabrics, Carboplate™ plates, or

Maperod™ rods. MapeWrap Primer 1 is prepared

by pouring Part B into Part A and mixing until the

resin is completely homogeneous. The mixing ratio

is 3 parts by weight of Part A to 1 part by weight

of Part B. MapeWrap Primer 1 is then applied by a

brush or roller onto a clean, dry and mechanically

sound substrate. MapeWrap Primer 1 remains

workable for 90 minutes at 73ºF (23ºC).

Product Code



U.S./ 7324002 Part A, 0.354 g (1,34 L) Canada 7324502 Part B, 0.133 g (0,50 L)

Product Code

Packaging

19

FR

P C

om

posite

Syste

ms

Normal-Setting, Thixotropic Epoxy Putty For

Smoothing and Leveling Concrete Surfaces

MapeWrap 11 is a two-component, epoxy resin-

based product with selected fine-graded aggregates

and special additives developed in MAPEI’s

research laboratories. MapeWrap 11 is used to

level concrete or reinforced concrete surfaces that

need to be repaired or reinforced by bonding the

MapeWrap fabrics, Carboplate carbon plates, and

Maperod carbon rods, and as a structural adhesive

for the Carboplate and Maperod systems.

MapeWrap™ 11

Product Code



U.S./ 7320106 Part A, 0.744 U.S. gal. (2,82 L) Canada 7320506 Part B, 0.265 U.S. gal. (1,00 L)

Product Code

Packaging

Pultruded, High-Strength Carbon Fiber Rod

Pre-Impregnated in Epoxy-Based Resin

Maperod C is a range of pultruded carbon fiber

rods, with high tensile strength and a modulus of

elasticity of 22.5 x 106 psi (155,000 N/mm²). After

the plastic film is removed, the Maperod C “near

surface-mounted” rods are used for structural

repairs and strengthening of structural elements in

reinforced concrete, brickwork, stone or volcanic

ash that has been damaged by either physical/

mechanical stresses or natural events. Maperod C

may be used together with the fabrics from the

MapeWrap™ range for stronger anchoring,

particularly when flexural or shear strengthening

operations are carried out.

Maperod™ C

Product Code



U.S./ 7339531 Rods: Maperod C 150/10, Canada 5/16" x 19.68' (8 mm x 6 m)

7339630 Rods: Maperod C 150/8, 3/8" x 19.68' (10 mm x 6 m)

Product Code

Packaging

Pultruded Carbon Fiber Plate Pre-

Impregnated in Epoxy-Based Resin

Carboplate E 170 is a range of pultruded carbon

fiber plates, with high resistance and flexibility, for

plating pre-stressed reinforced concrete and steel

structures. Carboplate E 170 is used for the repair

and upgrade of beams and slabs with increased live

loads, for reinforcing concrete structures damaged

by time and natural causes, and for anti-seismic

strengthening of structures built on earthquake

zones. Some application examples include an

increase in static and/or dynamic loads brought

on by equipment and machinery in industrial and

commercial structures, increased traffic volume on

bridges, and vibrating structures.

Carboplate™ E 170

Product Code



U.S./ 7330477 Roll: Carboplate E 170, Canada 4" x 164' (100 mm x 50 m)

7330476 Roll: Carboplate E 170, 4" x 82' (100 mm x 25 m)

7329976 Roll: Carboplate E 170, 2" x 82' (50 mm x 25 m)

Product Code

Packaging

20

FRP Composite Systems

Slow-Setting Epoxy Putty for Smoothing and

Leveling Concrete Surfaces

MapeWrap 12 is a two-component, epoxy resin for

leveling concrete or reinforced concrete surfaces

and as a structural adhesive for the Carboplate and

Maperod systems. MapeWrap 12 is recommended

in hot climates (applications at temperatures >

73ºF [23ºC]), or when leveling large surface areas.

MapeWrap 12 is prepared by pouring Part B into

Part A and mixing until the resin is completely

homogeneous. The mixing ratio is 3 parts by

weight of Part A to 1 part by weight of Part B.

MapeWrap 12 remains workable for about 60

minutes at 73ºF (23ºC).

MapeWrap™ 12

Product Code




Product Code

Packaging

Epoxy Resin for ‘Wet-Layup’ Saturation of

MapeWrap Fabrics

MapeWrap 21 is a two-component, super fluid,

solvent-free epoxy resin product, formulated for the

saturation of MapeWrap fabrics, immediately before

placing the fabric. The saturation is accomplished

by dipping the fabric into a trough or other

impregnation equipment. MapeWrap 21 is prepared


resin is completely homogeneous. The mixing

ratio is 4 parts by weight of Part A to 1 part by

weight of Part B. MapeWrap 21 remains workable

for 40 minutes at 73ºF (23ºC). The impregnated

fabric is applied over the still fresh MapeWrap 11

or MapeWrap 21, ensuring that it is laid without

wrinkles.

MapeWrap™ 21

Product Code




Product Code

Packaging

Epoxy Resin for ‘Dry-Layup’ Saturation of

MapeWrap Fabrics

MapeWrap 31 is a two-component, solvent-free

epoxy resin product, formulated for the saturation

of MapeWrap fabrics during application, using

the “dry-layup” system. MapeWrap 31 is prepared


resin is completely homogeneous. The mixing ratio

is 4 parts by weight of Part A to 1 part by weight

of Part B. MapeWrap 31 remains workable for 40

minutes at 73ºF (23ºC). MapeWrap 31 is applied

onto the still fresh MapeWrap 11 or MapeWrap 12

with a brush or short bristle roller, and the fabric is

then placed over the concrete element, removing

any wrinkles.

MapeWrap™ 31

Product Code




Product Code

Packaging

21

FR

P C

om

posite

Syste

ms

High-Strength, Uni-Directional Carbon Fiber

Fabric

MapeWrap C Uni-Ax is a mono-directional carbon

fiber fabric, having a high modulus of elasticity of

33.4 x 106 psi (230,000 N/mm²) and high tensile

strength. It is also available with an extremely high

modulus of elasticity of 56.6 x 106 psi (390,000

N/mm²) and additional widths on special order.

MapeWrap C Uni-Ax is used for the repair,

maintenance and static upgrade of deteriorated

structures in order to reinforce the tensile strength

of the section; for the reinforcement of load-

bearing elements in buildings; for the confinement

of axially loaded or damaged concrete elements

(columns, bridge piers, chimneys); and for seismic

strengthening.

MapeWrap™ C Uni-Ax

Product Code



U.S./ 7301550 Roll: MapeWrap C Uni-Ax 300, Canada 15.75" x 164' (40 cm x 50 m)

7303050 Roll: MapeWrap C Uni-Ax 600, 3/8" x 19.68' (10 mm x 6 m)

Product Code

Packaging

Balanced, High-Strength Quadri-Directional

Carbon Fiber Fabric

MapeWrap C Quadri-Ax is a quadri-directional

carbon fiber fabric especially suited for the

strengthening of structural elements that are

subjected to compressive and bending stress

where the distribution of equal pressure lines

are unknown, such as beam connections and

axial-loaded concrete structures. It is also used

for seismic strengthening of vaulted structures.

MapeWrap C Quadri-Ax can be placed using two

different methods: the “wet system” with the aid

of a machine that helps the impregnation process

before placement, and the “dry system” where the

resin is hand-applied during installation.

MapeWrap™ C Quadri-Ax

Product Code



U.S./ 7310050 Roll: MapeWrap C Quadri-Ax 380/50, Canada 11.8" x 164' (30 cm x 50 m)

Product Code

Packaging

Construction Grouts

Planigrout® 712

High-Performance, Nonshrink DOT Grout

Planigrout 712 is a one-component, nonshrinking,

nonmetallic, cement-based DOT (Department of

Transportation) grout that meets CRD C621 and

ASTM C1107 standards. Planigrout 712 contains

a corrosion inhibitor and silica fume, as well as

a special blend of aggregate and plasticizers that

provide exceptional placing and performance

characteristics.


E N H A N C E D

™

Product Code




Product Code

Packaging

Constru

ctio

n G

routs

22

High-Performance, Three-Part Epoxy

Machine Base Grout

Planigrout 830 SP is a three-part, 100%-solids,

high-performance precision machine grout for the

support of heavy equipment. Planigrout 830 SP

utilizes an engineered blend of graded aggregate

combined with epoxy resins that produces a grout

with exceptional flow and void-filling capability.

Planigrout 830 SP is chemically resistant and

features an exceptionally homogenous distribution

of aggregate. This makes it ideal for grouting

base plates exposed to the dynamic loading and

continuous vibration produced by heavy industrial

equipment.

Planigrout® 830 SP

U.S./ 38313 2 cu. ft. (0,057 m3) kit weighs Canada 300 lbs. (136 kg) and consists

of: Part A, Pail: 2.7 U.S. gals. (10,2 L) Part B, Can: 1.2 U.S. gals. (4,54 L) Part C: 4 bags of Aggregate, at 60 lbs. (27,2 kg) each

Product Code

Packaging

Construction Grouts

Cement-Based, General-Purpose

Construction Grout

Planigrout 755 is a one-component, nonshrinking,

cementitious construction grout consisting of

select fine aggregates and special additives.

Planigrout 755 requires only the addition of water

to produce consistencies varying from dry pack to

flowable. It produces excellent compressive and

flexural strengths within a few days.

Planigrout® 755

Product Code




Product Code

Packaging

Nonshrink, Precision Tremie Grout

Planigrout 740 is a high-strength, nonshrink,

precision, cementitious tremie grout composed of

select fine aggregates, special additives and silica

fume. Planigrout 740 requires only the addition

of water to produce a very flowable consistency,

without separation, allowing the grouting in hard-

to-reach spaces. Planigrout 740 ’s high-strength

and high-performance characteristics also make

it suitable for grouting of column and precision

machine baseplate. Containing anti-washout agents

and having a high resistance to chloride attack,

Planigrout 740 is a superior product for underwater

repairs and grouting areas subject to saltwater

exposure.

Planigrout® 740

Product Code




Product Code

Packaging

23

High-Performance, Fine-Grade

Concrete Resurfacer

Concrete Renew Fine is a one-component,

polymer-modified cementitious material for the

resurfacing of existing concrete. It allows a variety

of finishing options, including broom finishes and

decorative trowel finishes, on sidewalks, driveways,

steps and anywhere that has exposed concrete.

Concrete Renew Fine features a natural light

gray color that provides a uniform finish to

concrete surfaces.

Concrete Renew™ Fine

TM

Product Code




Product Code

Packaging

Exterior Finishing

High-Performance Concrete Resurfacer

Concrete Renew is a one-component, polymer-

modified cementitious material for the resurfacing

of existing concrete. It is suitable for broom

finishes and decorative trowel finishes on

sidewalks, driveways, steps and anywhere that

has exposed concrete. Concrete Renew features

a natural light gray color that provides a uniform,

like-new look to concrete surfaces.

Concrete Renew™

TM

Product Code




Product Code

Packaging

Constru

ctio

n G

routs

Exte

rior F

inish

ing

Polymer-Modified, Cementitious Scratch

and Brown Coat

Planitop Basecoat is a polymer-modified,

Portland-cement-based pre-blended mortar for

non-structural applications. Use Planitop Basecoat

for scratch or brown coat applications before the

application of a finish coat of acrylic or cement-

based stucco or waterproof paint. Gray-colored

Planitop Basecoat is suitable for applications on

concrete or masonry substrates, and properly

prepared wood and suitable Exterior Insulation

and Finish Systems (EIFS). Planitop Basecoat

may also be used as an adhesive and basecoat for

EPS (expanded polystyrene) architectural shapes,

and as a smoothing and leveling agent over

approved substrates. Planitop Basecoat conforms

to appropriate sections of ASTM C926, Standard

Specification for Application of Portland Cement-

Based Plaster.

Planitop™ Basecoat


Product Code

Packaging

® TM

® TM

24

Cement-Based Waterproofing Coating

Planiseal 88 is a one-component, polymer-

modified, cementitious coating for waterproofing

concrete and masonry surfaces.

Planiseal™ 88

U.S./ 8088025 (Gray) Bag: 55 lbs. (24,9 kg)Canada 8088125 (White) Bag: 55 lbs. (24,9 kg)

Product Code

Packaging

Waterproofing

All-Climate, Flexible Cementitious

Membrane for Waterproofing and Protecting

Concrete and Masonry

Mapelastic is a cementitious membrane that

waterproofs concrete and masonry. It also offers

protection against chemical attack from de-icing

salts, sulfates, chlorides and carbon dioxide

that leads to deterioration and costly repairs.

Mapelastic is designed for applications on new

concrete structures with hairline cracks, as well

as any cementitious surface subject to vibrations

and subsequent cracking. Use Mapelastic on such

hydraulic projects as irrigation canals and faces

of dams, in addition to swimming pools, water

features and storage tanks. Available in silver and

white, Mapelastic may also be used to waterproof

balconies, suspended walkways and patios.

Mapelastic™

U.S./ 39251000 (Silver) Part A, Bag: 50 lbs. (22,7 kg)Canada 39252000 (White) Part A, Bag: 50 lbs. (22,7 kg) 39257000 Part B, Jug: 2 U.S. gals. (7,57 L)

Product Code

Packaging

Roller-Grade, Flexible Cementitious

Membrane for Concrete Waterproofing

and Protection

Mapelastic Smart is a cementitious membrane

for protecting new concrete structures, concrete

structures repaired with Mapecem® or Planitop®

mortars, renders with hairline cracks, and any

cementitious surface subject to vibrations and

the subsequent cracking. Mapelastic Smart also

is designed for waterproofing such hydraulic

projects as channels and faces of dams as well as

swimming pools, basins, storage tanks, balconies

and terraces.

Mapelastic™ Smart

Product Code



U.S./ 39750000 Part A, Bag: 33.3 lbs. (15,1 kg)Canada 39757000 Part B, Jug: 2 U.S. gals. (7,57 L)

Product Code

Packaging

25

Wate

rpro

ofi

ng

Planiseal™ Plug

Product Code



U.S./ 0100005 Pail: 11 lbs. (4,99 kg) Canada 0100025 Pail: 55 lbs. (24,9 kg)

Product Code

Packaging

Ultra Quick-Setting Water Stop and

Anchoring Mortar

Planiseal Plug is an ultra quick-setting mortar

specially designed for stopping leaks, for repairing

voids and pockets in concrete, and for anchoring.

It is ideal for plugging active water leaks on

horizontal and vertical concrete surfaces in interior

or exterior applications.

Planiseal™ WR

Penetrating Water-Based Silane/Siloxane

Water Repellent

Planiseal WR is a new-technology, silane/siloxane-

blend, water-repellent, transparent sealer offering

superior performance and VOC compliance.

Planiseal WR offers fast-beading water repellency

for porous concrete, brick, stone and grout.

Planiseal WR is water-based, is easy to apply, and

provides a breathable, dirt- and stain-resistant

water repellency for the protection of concrete

surfaces.

Product Code



U.S./ 46468 Pail: 5 U.S. gals. (18,9 L)Canada

Product Code

Packaging

Hydrophilic, Expandable, Pre-Formed,

Flexible Rubber Strip for Watertight

Construction

Idrostop 5 is used to produce watertight

construction joints in civil, industrial and hydraulic

construction. Construction joints created with

Idrostop 5 are watertight up to 5 atm of pressure.

Unlike materials made of alternate composition

that lose efficiency in repeated wet/dry cycling,

Idrostop’s unique composition allows it to maintain

performance even in aggressive environments.

Idrostop™ 5

Packaging

U.S./ 176260 Case: 6 Rolls - 390' x 3/4" x 3/16" Canada (120 m x 20 mm x 5 mm)

Product Code

26

100%-Organic Pump Flush Agent

Resfoam PF is a 100%-organic blend of select,

high-temperature oils. Resfoam PF provides an

environmentally friendly and effective alternative

to hazardous products as a flush and cleaning

agent for removing polyurethane and other tough

composites from grout-injection equipment and

injection lines.

Resfoam™ PF

U.S./ 03368 5 U.S. gals. (18,9 L)Canada

Product Code

Packaging

Waterproofing

Nonwoven Fabric for Reinforcing

Waterproofing Membranes

Mapetex Sel is a macro-holed polypropylene fabric

reinforcement used together with Mapelastic™

and Mapelastic Smart flexible cementitious

membranes for waterproofing and protecting new

concrete surfaces or concrete units particularly

subject to large deformations and, therefore, at

risk of cracking. Mapetex Sel is also suitable for

use on surfaces at risk of cracking following repair

with products from the Mapecem® and Planitop®

product groups. Mapetex Sel can increase crack-

bridging capability up to 1/8” (3 mm).

Mapetex™ Sel

Product Code



U.S./ 281625 Roll: 3.3’ x 82’ (1 m x 25 m) Canada

Product Code

Packaging

Flexible Waterproof Tape for Moving Joints

Mapeband TPE is a professional-grade, highly

durable and flexible band for sealing and

waterproofing expansion joints and cracks

subject to movement up to 7/32” (5,5 mm).

TPE, an acronym for “elastomeric thermoplastic

polyolefine,” represents a group of polyolefines

that combine the best properties of thermoplastic

polymers and synthetic elastomer technology.

Mapeband™ TPE

U.S./ 795130 Roll: 17 cm x 30 m (6.7" x 98')Canada

Product Code

Packaging

27

Wate

rpro

ofi

ng

Rigid, Hydrophobic Polyurethane Grout for

Soil Stabilization

Resfoam SS 75 is a low-viscosity, hydrophobic

polyurethane used for soil stabilization in a

variety of water-bearing soils. The low viscosity of

Resfoam SS 75 provides for effective penetration

of the earth, adding structure and stabilization

by encapsulating the granules and subsequently

forming a rock-like mass. By application, Resfoam

SS 75 cures rapidly to a rigid closed cell, effectively

stopping water seepage and waterproofing the soil.

Resfoam SS 75 utilizes Resfoam HBA 5 catalyst,

which provides a variable reaction time.

Resfoam™ SS 75Resfoam™ HL 35

Flexible, Hydrophilic Polyurethane Foam or

Gel Resin

Resfoam HL 35 is a single-component, water-

activated hydrophilic polyurethane used for

sealing cracks or joints in concrete structures

that are subject to continuous moisture exposure.

Depending on the water-to-resin ratio, Resfoam

HL 35 will vary in consistency from a resilient

rubber-like foam to a flexible gel. Resfoam HL

35 is capable of absorbing water up to 800% of

its own mass and subsequently prevents water

from penetrating into a structure. This unique

feature allows Resfoam HL 35 to be used for large

water-inflow applications, such as manholes or

below-grade structures with active water leaks.

Once cured, Resfoam HL 35 provides a watertight,

elastomeric seal that stops the penetration of water

through cracks or voids.

Product Code



U.S./ 03674 Cartridge: 22 U.S. oz. (624 g)Canada 03668 Pail: 5 U.S. gals. (18,9 L)

Product Code

Packaging Product Code



U.S./ 02068 5 U.S. gals. (18,9 L)Canada 02991 HBA 5: 1 U.S. qt. (946 mL)

Product Code

Packaging

Flexible, Hydrophobic Polyurethane Grout

Resfoam HB 45 is a low-viscosity, flexible,

hydrophobic polyurethane grout used to stop

water infiltration in concrete structures. Resfoam

HB 45 is a solvent-free, MDI-based polymer

system that reacts with water. Use Resfoam HB

45 together with Resfoam HBA 5 accelerator to

adjust the reaction profile for a specific application.

In a free-rise circumstance, Resfoam HB 45 will

expand up to 750% of its liquid volume. Upon

application, Resfoam HB 45 reacts to form a

closed-cell polyurethane grout that will not shrink,

and provides an elastomeric waterproof barrier

sealing infiltration points against water intrusion.

Resfoam HB 45 is nontoxic and has good chemical

resistance. Resfoam HB 45 is also available in

a dual-cartridge format (Resfoam HB 45C) with

the accelerator already portioned in the Part B

cartridge.

Resfoam™ HB 45

Product Code

Packaging

U.S./ 02616 Dual cartridge: 22 U.S. oz. (624 g) Canada 02668 Pail: 5 U.S. gals. (18,9 L)

U.S./ 02991 1 U.S. qt. (946 mL)Canada

Product Code

Packaging

Resfoam HBA 5

28

Repair Epoxies

Low-Viscosity Injection Resin for

Crack Repair

Planibond CR 50 is a two-part, low-viscosity

injection resin that deeply penetrates the finest

hairline cracks, restoring the structural integrity

of concrete. High-strength and moisture-tolerant,

Planibond CR 50 meets ASTM C881 requirements

Types I, II, IV and V; and Grade 1, Class B and C;

as well as USDA specifications for food-processing

areas. Planibond CR 50 may be applied by

pressure injection or gravity feed, and can also be

combined with sand to become an epoxy mortar

or grout. Planibond CR 50 features a fluorescent

tracer dye, allowing easy analysis of penetration in

repair core samples.

Planibond® CR 50

Product Code



U.S./ 46199 Dual cartridge: 13.5 U.S. oz. (399 mL)Canada 46161 Kit: 3 U.S. gals. (11,4 L)

Product Code

Packaging

Planibond® AE

High-Strength, Nonsag Epoxy Anchoring Gel

Planibond AE is a high-strength, two-part, nonsag,

epoxy anchoring gel designed for a wide variety

of bonding and repair applications. With VOC

compliance and low odor, Planibond AE meets

ASTM C881 requirements Types I, II, IV and V;

and Grade 3, Classes B and C; as well as USDA

specifications for food-processing areas. Planibond

AE is moisture-tolerant and may be extended with

graded sands. Planibond AE adheres to masonry,

concrete, steel and other structural materials.

Product Code



U.S./ 40474 Dual cartridge: 20.2 U.S. oz. (600 mL) Canada 40453 2 U.S. gals. (7,57 L)

Product Code

Packaging

High-Modulus Epoxy Bonding Agent

Planibond EBA is a two-component, multipurpose

high-modulus epoxy bonding agent. Planibond

EBA is nonshrink, 100%-solids and moisture-

insensitive. Planibond EBA is used primarily as

a bonding agent for screeds and repair mortars,

with applications for anchoring and crack repair.

Planibond EBA meets ASTM C881 requirements.

Planibond® EBA

U.S./ 40158000 Kit: 2 U.S. gals. (7,57 L) Canada 40169000 Part A: 5 U.S. gals. (18,9 L)

40269000 Part B: 5 U.S. gals. (18,9 L)

Product Code

Packaging

29

Adm

ixture

s

Shrinkage- and Crack-Reduction

Curing Additive

Mapecure SRA is a liquid admixture that reacts

chemically to reduce hydraulic shrinkage and

the formation of microcracks. Mapecure SRA

is compatible with traditional MAPEI concrete

restoration materials, such as cementitious grouts

and most repair mortars.

Mapecure™ SRA

Product Code



U.S./ 169720 Pail: 5 U.S. gals. (18,9 L) Canada

Product Code

Packaging

Universal Latex Additive

For Professional Use

Planicrete UA is a next-generation, water-based,

one-component, concentrated liquid latex

admixture used to enhance the performance of

several MAPEI products, including mortar mixes.

Using Planicrete UA as part of the designated

design mixes will increase product performance

in the areas of bond, flexural and tensile strengths

in addition to increased durability and enhanced

workability.

Planicrete® UA

Product Code



U.S./ 36253 Jug: 1 U.S. gal. (3,79 L)Canada 36268 Pail: 5 U.S. gals. (18,9 L)

Product Code

Packaging

Admixtures

Acrylic Latex Admixture for Mortar

and Concrete

Planicrete AC is a one-component, concentrated,

liquid latex admixture used to enhance the

performance of cementitious repair mortars,

plasters, stuccos, concrete mixes and toppings for

the restoration of horizontal, vertical and overhead

concrete; concrete masonry units (CMUs); and

masonry surfaces.

Planicrete® AC

Product Code



U.S./ 7013004 Jug: 1 U.S. gal. (3,79 L)Canada 7013020 Pail: 5 U.S. gals. (18,9 L)

Product Code

Packaging

Repair E

poxie

s

30

Coatings and Sealers

Premium High-Gloss, Water-Based

Acrylic Sealer

Mapefinish Wet Look is a one-part, water-based,

transparent, high-gloss sealer designed for

protecting and enhancing colors in all concrete

surfaces – from highly textured stamped concrete

to smooth self-leveling toppings. Mapefinish

Wet Look utilizes acrylic epoxy hybrid resins that

offer superior abrasion, blush and slip resistance,

outperforming most solvent-based acrylics and

many urethane dispersions. Mapefinish Wet

Look is low in VOCs, odor-free and permeable to

water vapor, making it perfect for application on

interior and exterior concrete surfaces. With its

superior performance combined with user-friendly

application, Mapefinish Wet Look is an ideal sealer

for concrete and masonry.

Mapefinish™ Wet Look

Product Code



U.S./ 31668000 Pail: 5 U.S. gals. (18,9 L) Canada

Product Code

Packaging

Three-Component, Cement-Based

Anticorrosion and Bonding Agent

Planibond 3C is a three-component corrosion

inhibitor and bonding agent system consisting

of water-based, solvent-free, moisture-tolerant,

epoxy-modified corrosion inhibitors. It can be

applied using a brush, short-nap roller, push

broom or hopper spray equipment. Planibond

3C excels as a cementitious bonding agent and

corrosion protection treatment. Use Planibond 3C

on all exposed reinforcing steel and as a bonding

agent before the placement of repair products.

Planibond® 3C

Corrosion-Inhibiting Coating for

Reinforcing Steel

Mapefer 1K is a one-component anticorrosion

coating based on unique polymers, cementitious

binders and corrosion inhibitors. Mapefer 1K

is specially formulated for application on clean

reinforcing steel to inhibit oxidation and rust

formation.

Mapefer™ 1K

Product Code

Product Code




U.S./ 276645 10 lbs. (4,54 kg) Canada

U.S./ 36364000 1 large kit Canada

Product Code

Product Code

Packaging Packaging

Corrosion Protection


E N H A N C E D

™

31

Corro

sion P

rote

ctio

nC

oatin

gs a

nd S

eale

rs

Low-Viscosity Epoxies for Sealing Concrete

Bridge Decks

Planiseal LVB is a two-component, very low-

viscosity epoxy sealer designed to deeply penetrate

into new or worn sound concrete. Planiseal LVB

seals hairline cracks and penetrate the concrete

pore structure to form a subsurface barrier that

effectively arrests carbonation as well as stopping

the penetration of chloride ions into concrete

decks. Planiseal LVB significantly improves the

durability and service life of concrete decks.

Planiseal™ LVB

Epoxy Overlay for Vehicular and

Pedestrian Traffic

Planiseal Traffic Coat is a solvent-free, moisture-

tolerant, 100%-solids, unique low-modulus, two-

part, epoxy bonding agent and binder engineered

for providing a waterproof and skid-resistant

overlay on such surfaces as bridges, elevated

slabs, parking garages and balconies. Planiseal

Traffic Coat arrests carbonation and stops the

penetration of chloride ions into concrete decks,

while providing a skid-resistant, durable and

attractive finish.

Planiseal™ Traffic Coat

U.S./ 46557 Kit: 2 U.S. gals. (7,57 L) Canada 46568 Part A: 5 U.S. gals. (18,9 L)

46569 Part B: 5 U.S. gals. (18,9 L) 46577 Part A: 55 U.S. gals. (208 L)

46578 Part B: 55 U.S. gals. (208 L)

Product Code

Product Code

Packaging Packaging

U.S./ 46768 Part A, Canada Pail: 5 U.S. gals. (18,9 L) 46769 Part B, Pail: 5 U.S. gals. (18,9 L) 46777 Part A, Drum: 55 U.S. gals. (208 L) 46778 Part B, Drum: 55 U.S. gals. (208 L)

Clear, High-Gloss, 100%-Solids

Epoxy Sealer

Planiseal HG is a solvent-free, moisture-tolerant,

100%-solids, clear, high-gloss, two-component

epoxy sealer suitable for sealing concrete as well as

concrete areas treated with skid-resistant Planiseal

Traffic Coat.

Planiseal™ HG

Product Code



U.S./ 46661 Kit: 3 U.S. gals. (11,4 L)Canada

Product Code

Packaging

32

Semi-Rigid Epoxy Joint Filler

Planibond JF is a two-part, 100%-solids, moisture-

tolerant, semi-rigid epoxy joint filler. Planibond JF

meets ASTM C881 and ACI 302 requirements as

well as USDA specifications for food-processing

areas. The self-leveling Planibond JF is ideal for

filling and sealing horizontal non-moving saw-cut

control joints and random cracks.

Planibond® JF

Product Code



U.S./ 46057 Kit: 2 U.S. gals. (7,57 L)Canada 46074 Dual cartridge: 20.2 U.S. oz. (600 mL)

Product Code

Packaging

Sealants and Joint Fil lers

One-Component, Nonsag Elastomeric

Polyurethane Sealant

Mapeflex P1 is a high-performance, one-part

elastomeric polyurethane sealant and adhesive.

Mapeflex P1 offers excellent adhesion to most

surfaces, superior gunning and tooling, as well as

excellent flexibility for moving joints. Mapeflex P1

meets the requirements of ASTM C920, Type S,

Grade NS, Class 25, Uses NT, T, M, G, A and O;

TT-S-00230C, Type II, Class A; AAMA 808.3-92;

and CAN/CGSB-19.13-M87.

Mapeflex™ P1

One-Component, Self-Leveling Elastomeric

Polyurethane Sealant

Mapeflex P1 SL is a high-performance, one-part,

self-leveling elastomeric polyurethane sealant.

Mapeflex P1 SL offers superior adhesion to

most surfaces, durability and excellent flexibility

for moving joints. Mapeflex P1 SL meets the

requirements of ASTM C920, Type S, Grade P,

Class 25, Uses T, M, G, A and O; TT-S-00230C,

Type I, Class A; and CAN/CGSB-19.13-M87.

Mapeflex™ P1 SL

Product Code

Product Code

PackagingPackaging ProductCode

PackagingProduct PackagingProductCode


U.S./ 44919 Cartridge: 29 U.S. oz. (857 mL)Canada (6 per case)

U.S./ 44918 Sausage: 20.2 U.S. oz. (600 mL) Canada (20 per case)

Product Code

Product Code

PackagingPackaging

TM TM

Self-Leveling Polyurea Floor Joint Filler

Planiseal RapidJoint 15 is a 100%-solids, two-

component, rapid-curing, polyurea elastomer

joint and crack filler. Planiseal RapidJoint 15 is

designed for supporting non-moving joint nosings

exposed to forklift and steel-wheeled traffic.

Planiseal RapidJoint 15 features broad temperature

capabilities, can address joint movement of 10%

to 15%, and cures quickly so that repaired joints

can be re-opened to traffic almost immediately after

application. Designed with enhanced application

characteristics, excess Planiseal RapidJoint 15 can

be shaved easily, and will typically not leave a stain

on surfaces adjacent to joints.

Planiseal™ RapidJoint 15

Product Code



U.S./ 45274 Dual cartridge: 20.2 U.S. oz. Canada (600 mL)

Product Code

Packaging

Seala

nts a

nd Jo

int F

illers

33

34

The MAPEI Technical Institute (MTI) provides the highest-quality, hands-on technical training to architects, contractors, installers and distributors in 7 locations: Deerfield Beach (FL), San Bernardino (CA), Garland (TX), and Dalton (GA), all in the USA; and Brampton (Ontario), Laval (Quebec), and Delta (British Columbia), all in Canada. At the Laval MTI location, seminars are offered in either English or French.

U.S. seminars Canadian seminars

Concrete Restoration Systems (CRS)

Floor Covering Installation Systems (FCIS)

Tile & Stone Installation Systems (TSIS)

Basics and Hands-On TrainingOne- or two-day class that focuses on levelers, toppings, moisture mitigation and concrete repair.

Basics and Hands-On Training One- or two-day class that covers products for surface preparation, moisture mitigation, vinyl, rubber, carpet and wood flooring.

Basics and Hands-On TrainingOne- or two-day class that covers products for surface preparation, waterproofing, crack isolation, tile and stone installation, and grouting.

Training 101, Basics: Surface preparation, one-step repair mortar and systems.

Training 101, Basics: Surface-preparation products, multipurpose adhesives and specialized adhesives.

Training 101, Basics: Surface-preparation products, thin-set mortars, adhesives and grouts.

2012 Training Seminars

> For registration information on U.S. seminars, please contact Sophia D’Amico-Campbell at (954) 246-8555.

> For registration information on Canadian seminars, please contact Raffaelina Aceto at (450) 662-1212.

35

Floor Covering Installation Systems

Adhesives and Accessories

Tile & Stone Installation Systems

Systems

Skimcoats and Additives

Underlayments

Membranes

Sound Reduction

Mortars

Modified Mortar

Additives

Additives


Underlayments

Compounds

Headquarters of the Americas1144 East Newport Center Drive Deerfield Beach, FL 33442

Customer Service1-800-42-MAPEI (1-800-426-2734)

Technical Services1-800-992-6273 (U.S. and Puerto Rico)1-800-361-9309 (Canada)

Services in Mexico 0-1-800-MX-MAPEI (0-1-800-696-2734)

NORTH AMERICA United States Arizona California Florida Georgia Illinois New Jersey Texas Virginia

Canada British Columbia Ontario Quebec

Mexico

AustriaBelgiumBeneluxBulgariaCroatiaCzech RepublicFinlandFranceGermanyGreeceHungaryItalyLuxembourg

NetherlandsNorwayPolandPortugalRomaniaRussiaSlovakiaSloveniaSpainSwedenSwitzerlandUkraineUnited Kingdom

EUROPE

SOUTH AMERICA/CARIBBEAN

ArgentinaPuerto Rico

Venezuela

United Arab EmiratesAustraliaChinaHong Kong

IndiaMalaysiaNew ZealandSingaporeVietnam

Egypt

ASIA/OCEANIA

AFRICA


MAPEI Headquarters of the Americas 1144 East Newport Center Drive Deerfield Beach, Florida 33442 Phone: 1-888-US-MAPEI

(1-888-876-2734)

Technical Services 1-800-992-6273 (U.S. and Puerto Rico) 1-800-361-9309 (Canada)

Customer Service 1-800-42-MAPEI (1-800-426-2734)

Services in Mexico 0-1-800-MX-MAPEI (0-1-800-696-2734)

For the most current BEST-BACKED™ product data and warranty information,

visit www.mapei.com.

Edition Date: December 13, 2011

PR6282_1211 Printed in the USA.

Copyright ©2012 by MAPEI Corporation (“MAPEI”) and all rights are reserved. MAPEI does not guarantee or warrant the accuracy or completeness of this document. Nor does MAPEI assume any responsibility arising from the reader’s reliance on the information in this document. MAPEI denies all liability for damages of any kind arising from any errors, omissions or inaccuracies in this document, or resulting from any reader’s reliance on this document. Therefore, MAPEI disclaims all express and implied warranties, including, but not limited to the implied warranties of MERCHANTABILITY and FITNESS FOR A PARTICULAR PURPOSE. All intellectual property rights and other information contained in this document are the exclusive property of MAPEI (or its parent or related companies), unless otherwise noted. No part of this document may be reproduced or transmitted in any form without the prior written consent of MAPEI.

Date post:	07-Nov-2014
Category:	Documents
Upload:	conifer-yu
View:	37 times
Download:	3 times

101_US-EN

Documents