1042641 uponor pc ic is 2012

I N D O O R C L I M AT E S O LU T I O N S

P R O D U C T C ATA LO G 2 0 1 2

Uponor Radiant Heating/Cooling

Uponor Renovationsystem MinitecUponor Minitec - System components and accessories ·························································· 8

Uponor lightweight panel SiccusUponor Siccus - System components and accessories ···························································· 11

Uponor pipe positioning panel TectoUponor Tecto - System components and accessories ······························································ 14

Uponor self attaching systemUponor self attaching system - System components and accessories ····································· 19

Uponor stapler and clamp trackUponor stapler and clamp track - System components and accessories ·································· 22

Uponor pipe positioning panelUponor pipe positioning panel - System components and accessories ··································· 27

Uponor steel mesh ClassicUponor Classic - System components and accessories ···························································· 32

Uponor Plaster Ceiling CoolingUponor Plaster Wall/Ceiling H/C - System components and accessories ······························· 35

Uponor heat emission plate ······························································································· 38

Uponor Radiant Heating/Cooling > List of content

List of content

Abbreviations ······················································································································ 4

EEI-Int-RHC-01.12 3

Uponor underfloor heating accessoriesUponor underfloor heating accessories ·················································································· 39

Uponor underfloor heating manifoldsUponor modular plastic manifolds ·························································································· 42Uponor accessories for plastic manifolds ················································································ 43Uponor stainless steel manifolds ···························································································· 45Uponor manifold accessories ·································································································· 46Uponor pipe bend support ····································································································· 48Uponor manifold cabinets ······································································································ 48

A/F [mm] across flatsA [m²] square measurec/c [mm] centre - centre distancec/c1 [mm] centre - centre distance 1colour [-] colourCon. [l/m²] consumptiond [mm] diameterd1 [mm] diameter 1d2 [mm] diameter 2d3 [mm] diameter 3di [mm] diameter insideDN [mm] diameter nominalDT [d] drying time in daysEP/a [W] effective power per actuatorFT ["] female threadFT m [-] female thread (metric)G [kN/m²] load bearing capacityh [mm] heighth1 [mm] height 1h2 [mm] height 2l [mm] lengthl [m] length in meterl1 [mm] length 1MT ["] male threadoutlets [-] Number of outletsOV [V] operating voltagep [bar] pressureP [W] effective powerQ [kW] nominal powerr [mm] radiusR-value [m²K/W] thermal resistances [mm] strength / wall thicknesssd [mm] side distancestroke [mm] strokeType [-] TypeV [l/m] volumew [mm] widthw [m] width in meterw1 [mm] width 1w2 [mm] width 2z [mm] z-valueΔ Lw [dB] impact noise improvement

Uponor Radiant Heating/Cooling > Abbreviations

Abbreviations

EEI-Int-RHC-01.124

Shortcut unit Description

Uponor controlsUponor Radio control ············································································································· 50Uponor outdoor sensor ·········································································································· 54Uponor wired control ············································································································· 55Uponor control accessories 24 V ···························································································· 59Uponor wired control 230 V ··································································································· 60Uponor control accessories 230 V ·························································································· 61Uponor climate controller ······································································································· 63Uponor control stations ·········································································································· 67

Uponor industrial underfloor heatingUponor industrial floor heating PE-Xa pipes ·········································································· 71Uponor PE-Xa Q&E fittings ···································································································· 72Uponor industrial floor heating fixation and accessories ························································ 73Uponor industrial floor heating manifold and accessories ······················································ 75

Uponor snow and ice meltingUponor snow and ice melting pipes························································································ 77Uponor snow and ice melting manifold and accessories ························································· 78

Uponor sport floor heatingUponor sport floor PE-Xa pipes ······························································································ 83Uponor sport floor PE-Xa Q&E fittings ·················································································· 84Uponor sport floor fixation and accessories ··········································································· 85

Uponor comfort panelUponor comfort panel ············································································································ 88Uponor comfort panel - accessories ······················································································· 90

Uponor gypsum panelUponor gypsum panel ············································································································ 96Uponor gypsum panel - accessories ······················································································· 97

Uponor toolsUponor tools ·························································································································· 99

Uponor Radiant Heating/Cooling > List of content

List of content

EEI-Int-RHC-01.12 5

International sales and delivery terms ············································································· 105

Item search register ············································································································ 107

How to contact us ··············································································································· 111

6 EEI-Int-RHC-01.12

Radiant heating and cooling systems - for all areas of application the right system

Radiant heating and cooling systems

Accessory systems

Floor – Renovation

Floor – new build, SFH, MFH, public buildings

Wall/Ceiling - new build and renovation

Minitec

Minimum height, maxi-mum comfort

Fittings

For each pipe a save connection

Siccus

The lightweight for renovation

UFH accessories

To have the right accessories is what matters

Tecto

For fast and accurate laying

Manifolds

Balanced distribution of heat into the last corner

Self attaching system

Micro interlocking for maximum holding force

Cabinets

For surface and fl ush installation

Special Applications

Industrial UFH

Heating/Cooling of productions halls, warehouses or logistic centers

Snow & ice melting

Keeping areas snow & ice free

Sports fl oor heating

Sports fl oor heating for surface elastic fl oors

Comfort panel

Ceiling cooling for suspended ceilings

x

x

x

x

x x

x

x

x

x

x

x

x

x

7EEI-Int-RHC-01.12

Stapler and clamp track

Versatile through fl exible pipe laying

Pipe positioning panel 14 – 16


Classic

Proven for years, precise laying

Controls

Wired or wireless controlled, sensitive and comfortable

20,5

Control stations

Energy effi cient supply temperature control

Tools

which makes the work easier

Plaster Wall/Ceiling

Multifunctional for wall and ceiling

Ceiling cooling systems

Gypsum panel

Ceiling cooling for gypsum board ceilings

Contec

The storable concrete core activation

Contec ON

The highly effi cient surface close building part activation

Stapler and clamp track

Versatile through fl exible pipe laying

Pipe positioning panel 14 – 16


Classic

Proven for years, precise laying

Controls

Wired or wireless controlled, sensitive and comfortable

20,5

Control stations

Energy effi cient supply temperature control

Tools

which makes the work easier

Plaster Wall/Ceiling

Multifunctional for wall and ceiling

Ceiling cooling systems

Gypsum panel

Ceiling cooling for gypsum board ceilings

Contec

The storable concrete core activation

Contec ON

The highly effi cient surface close building part activation

x

x

x

x

x

x

x

x x

x

x

x

Uponor Radiant Heating/Cooling > Uponor Renovationsystem Minitec

EEI-Int-RHC-01.128

Fast installation, short heat-up time: the Uponor renovation-system Minitec off ers you a range of advantages. The Uponor minitec foil element for the laying of the PE-Xa pipes measures 9.9 x 1.1 mm and can be installed on any existing

screed, timber of tiled fl oor. Thanks to this small element height of around one centimetre, the system is particularly suitable for inte-gration into existing buildings.

Your advantages Ideal for retrofi tting in existing buildings during renovations Suitable for direct installation on screed or tiled fl oors Elements height only 12 milimeter Low-cost installation of foil elements and pipe Foil elements can be walked over immediately aft er installa-

tion Short heat-up times Low heating water temperatures Can be connected directly to existing radiant heating sys-

tems

System components

Uponor high performance panel

Room controls

Uponor radio controlUponor wired control 24 V230 V components

Control stations

Uponor control stations - overview

System pipe/fi ttings

Uponor PE-Xapipe 9,9 x 1,1

Additional components

Uponor Minitecedging strip

Manifold/Cabinets

Uponor PE-Xa Q&E coupling

Uponor Minitecjoint profi le

Uponor Minitecclamp track 9.9

Uponor PE-Xa conversion nipple

Uponor renovationsystem Minitec

Uponor Minitecjoint protection

Uponor pipe connection PE-Xa 9.9

Uponor PE-Xa Pipe 9.9x1.1 expander

20,5

Uponor cabinet

Uponor manifold connection valve set G 1/Rp 1

Uponor manifold

e.g. can be used with Knauf Levelling Screed 425

http://www.knauf.de/pdf/bilder/detbl_wmv/f422_e_2011_01.pdf


Uponor Minitec - System components and accessories

Uponor Minitec high-performance panelDesigned as sturdy pipe fixing panel of minimum height, with integrated pipe laying channels for correct pipe laying distances; designed for Uponor Minitec PE-Xa pipes 9.9 x 1.1 mm; allowing for straight and diagonal pipe laying; with undercut, deep pipe fixing studs; overlap on both sides with triangular studs; perforated panel for installation between levelling compound and substructure; with self-adhesive back for proper fixture to screed and tiled floorsMaterial: PolystyreneDIN 4102 building material class: B2Pipe spacing: Vz 5, 10, 15Colour: traffic black (near RAL 9017)

Item no. h [mm] l [mm] w [mm] A [m²] Description unit

1005261 12 1120 720 0.77 Uponor Minitec high performance panelwith,self-adhesive layer for pipes 9.9mm 15.4 m²

Uponor PE-Xa pipesPE-Xa pipe with an oxygen diffusion barrier manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method complying with e.g. prENISO 15875 “Plastics piping systems for hot and cold water installations - Cross-linked polyethylene” with an oxygen diffusion barrier of EVOH (ethyl vinyl alcohol). Uponor pipes fulfil the requirements for oxygen diffusion resistance as per DIN 4726. Malfunction temperature 95°C. Design pressure 8,8 bar (at 70°C).

Item no. d [mm] s [mm] l [m] V [l/m] Description unit

1033024 9.9 1.1 120 0.047 Uponor eval PE-Xa pipe 9.9x1.1 120 m



Uponor PE-Xa Q&E coupling 9.9For Uponor PE-Xa pipe 9.9 x 1.1 mm, consisting of:- 1 coupling- 2 PEX Q&E rings for secure connectionMaterial: Coupling made in brass; PEX Q&E rings made in high-pressure cross-linked polyethylene

Item no. d [mm] s [mm] l [mm] z [mm] Description unit

1005264 9.9 1.1 34 4 Uponor PE-Xa Q&E coupling 9.9-9.9with two PEX rings 10 pcs

Uponor PE-X ring for PE-Xa pipesFor Uponor Minitec PE-Xa pipe 9.9 x 1.1 mm; to secure fixing to Minitec fittingsMaterial: High-pressure cross-linked polyethylene (PE-Xa)

Item no. d [mm] Description unit

1005263 9.9 Uponor PE-X ring for PE-Xa pipes9.9 x 1.1 10 pcs

Uponor PE-Xa conversion nippleFor Uponor PE-Xa pipes 9.9 x 1.1 mm, made of brass.

Item no. d [mm] MT ["] l [mm] z [mm] A/F [mm] Description unit

1005265 9.9 R 1/2 39 14 22 Uponor PE-Xa conversion nipple9.9 - 1/2 with one PEX ring 10 pcs

EEI-Int-RHC-01.12 9


Uponor Minitec - System components and accessories

Uponor edging strip, 80x8Edging strip for high performance panel conforming to DIN 18560, made of polyethylene with self-adhesive backing, self-adhesive strip on outer face provides tight seal between edging strip and insulation;Length of roll: 20 m

Item no. h [mm] l1 [mm] s [mm] l [m] Description unit

1005267 80 70 8 20 Uponor Minitec edging strip, 80 x 8in length of 20 m 200 m

Uponor joint profile 40x10Self-adhesive clamp-on profile element for high performance panel made of hard PVC with polyethylene foam expansion strip, for the reliable separation of screed sections (e.g. in doorways), and to absorb expansion of screed. For expansion joints as per DIN 18560-2.Height: 40 mmMaterial thickness: 10 mmLength: 1,8 m

Item no. l [mm] s [mm] w [mm] h [mm] Description unit

1005268 1800 10 50 40 Uponor Minitec joint profile40 x 10, length 1.8 m 18 m

l

b

s

Uponor joint protection 9.9mmMade of PE-LD, with slit opening, for protection of pipes up to 9.9 mm in areas of expansion joints. Length: 300 mm

Item no. l [mm] s [mm] w [mm] Description unit

1005269 300 2 35 Uponor joint protection tube forPE-Xa pipes 9.9 x 1.1, length 300 mm 30 pcs

ra

d

h

l b

Uponor clamp track 9.9Self-adhesive U-profile strip made of recycled material, with integrated pipe holder for 9.9 x 1.1 mm Uponor PE-Xa pipes.Length of track: 2.5 mWidth of track: 24 mmSpace between pipe holders: 20 mm c/cInstallation height with pipe: 13 mm

Item no. l [mm] w [mm] h [mm] d [mm] c/c [mm] Description unit

1005274 2500 24 13 10 20 Uponor clamp track 9.9 mm 25 m

EEI-Int-RHC-01.1210

Uponor Radiant Heating/Cooling > Uponor lightweight panel Siccus

EEI-Int-RHC-01.12 11

e.g. can be used with Knauf Brio Pre-fab Floor Screed Elements

Uponor lightweight panel Siccus

The Uponor lightweight panel Siccus has been specially designed as a universal solu-tion for the restoration of old buildings where a low con-struction height and low weight are very important. The panels are installed on the

fl oor below the load distribution layer consisting of dry screed panels or heating screeds.

Your advantages Minimum fl oor construction height from 50 mm Short installation time, immediately accessible if installed

with dry screed Low static weight from 25 kg/m² Last with dry screed

panels Specially devised installation panel for universal use

System components

Uponor Siccus lightweight panel

Uponor Siccusheat emission plate

Uponor PE Foil 0.2mmPE-type 200

Room controls


Control stations


20,5


Uponor edging strip

Manifold/Cabinets

Uponor manifold

Uponor joint profi le 100x10

Uponor compression adapter PE-Xa and MLCP

Uponor joint protection 20mm

Uponor marking set

Uponor screed additive

Uponor PE foil 0.2 mm

Uponor cabinet


Systempipe/-Fittings

PE-Xa pipe 14x2

Uponor MLCP 14 pipe

MLC press coupling14x2


http://www.knauf.de/pdf/bilder/detbl_wmv/f12_e_2007-02.pdf


Uponor Siccus - System components and accessories

Uponor Siccus lightweight panelPipe fixing panel for butt joint installation; with pipe channels for the installation of heat emission plates or Uponor PE-Xa pipes 14 x 2 mm and Uponor MLCP pipes 14 mmMaterial: Expanded polystyrene rigid foam according to DIN EN 13163DIN 4102 building material class: B1Application type according to DIN 4108-10: DEOCompressive strength: = 150 kPaTechnical dataPlate size: 1197 x 1050 mmPlate thickness: 25 mmThermal resistance: 0.622 m2 K/WPayload: 7.5 kN/m2Pipe spacing: 15 cm, 22.5 cm or 30 cm

Item no. l [mm] w [mm] h [mm] A [m²] Description unit

1005485 1197 1050 25 1.25 Uponor Siccus lightweight panel 12.5 m²

l

b

Uponor heat emission plate 14 mmFor installation on Uponor lightweight panel; ensures uniform heat distribution and proper fixture of Uponor PE-Xa pipes 14 x 2 mm and Uponor MLCP RED radiant heating pipes 14 x 1.6 mm; with double perforations for easy cutting to size.Material: AluminiumPlate size: 120 x 1180 mmPlate thickness: 0.45 mmMaterial requirement:Pipe spacing Va 15 = 5.6 plates/m2Pipe spacing Va 22.5 = 3.7 plates/m2Pipe spacing Va 30 = 2.8 plates/m2

Item no. l [mm] w [mm] Description unit

1005486 1180 120 Uponor Siccus heat emission plate 14 mmfor lightweight panel, 1180 x 120 mm 48 pcs

Uponor PE foil 0.2mmFor installation on Uponor insulation or on standardised insulating material approved for the intended purpose for areas without stud foil. Prevents screed penetrating the underlying insulation.Dimensions: 4 m x 2.5 m Thickness: 0.2 mm

Item no. l [m] w [m] s [mm] Description unit

1005049 60 1.25 ~0.2 Uponor PE foil 0.2 mm thickness60 x 1.25 m 75 m²

Uponor PE-Xa pipeas coil, for use as radiant heating pipe, connected by Q&E, press or clamp fittings.Material: Uponor PE-Xa pipe made in high-pressure cross-linked polyethylene (Engel method), conforming to DIN 16892 and DIN ISO 15875, oxygen-tight according to DIN 4726Colour: white with black and red longitudinal stripes

Uponor PE-Xa pipeMax. operating temperature: 90°CMax. operating pressure: 6 bar at 70 °CApplication class: 4 / 6 bar

Item no. d [mm] s [mm] l [m] Description unit

1048290 14 2 240 Uponor eval PE-Xa Q&E pipe 14x2.0240 m coil 240 m


EEI-Int-RHC-01.1212


Uponor Siccus - System components and accessories

Uponor MLCP white in coilsDiffusion-tight multi-layer composite pipe (PE-RT - adhesive - longitudinally welded aluminium - adhesive - PE-RT) for distribution conduits, rising mains and connection lines for plumbing, radiator connection and fancoil connection. Fire classification E according to DIN EN 13501-1. Pipe end caps as hygienic seal according EN 806.Resistance of temperature:Tap water: The maximum permanent operating temperature exists between 0°C and 70°C at a maximum permanent operating pressure of 10 bars. The short-term malfunction temperature is 95°C of a maximum of 100 hours in the operating lifetime.Heating: The maximum permanent operating temperature is 80°C at a maximum permanent operating pressure of 10 bars. The short-term malfunction temperature is 95°C of a maximum of 150 hours in the operating time per year.


1013366 14 2.0 200 Uponor MLCP 14x2white in coils 200m 200 m

Uponor Q&E Couplingfor Uponor PEXa pipe consisting of:1 Coupling / Brass2 PEX-Rings for secure connection / cross linked Polyethylene


1058659 14 Uponor Q&E Coupling 14with two eval Rings, nature 10 pcs

Uponor Q&E Ring naturalMade of PE-X. Uponor rings natural intended for Uponor Q&E fittings.

Item no. d [mm] colour [-] Description unit

1058428 14 natural Uponor Q&E ring eval without stop edgenature 14 20 pcs

Uponor press coupling MLC up to 32Made of tin-plated brass, with fixed press sleeve, stop ring, pressed identification, colour code and test safety. Press without bevel.


1015154 14 Uponor press coupling MLC 14-14 10 pcs


Uponor Radiant Heating/Cooling > Uponor pipe positioning panel Tecto

EEI-Int-RHC-01.1214

Uponor pipe positioning panel Tecto

The Uponor Tecto pipe posi-tioning panel has been spe-cially developed for the instal-lation of underfl oor heating/cooling systems in residential and non-residential buildings. The panels are installed in the fl oor below the cement or

anhydrite screed load distribution layer. Uponor Tecto panels are available in two diff erent thicknesses (ND 30-2 and ND 11), catering for various fl oor constructions and load-bearing require-ments.

Your advantages Cost-effi cient one-man installation Easy laying thanks to large panels (1450 x 850 mm) Compensation elements for doors, movements joints and

wall joints available Double-sided strips for easy connection of element cut-off s

with minimum waste Diagonal pipe fi xture for installation at 45° angles Suitable pipe sizes from 14 to 17 mm Ensures standardised pipe spacing due to forced pipe paths Proper covering of the insulating layer thanks to integrated

sturdy deep-drawn foil Suitable for a wide range of applications thanks to high

strength properties (ND 30-2: 500 kg/m²; ND 11: 3.0 t/m²)

System components

Uponor Tecto pipe positioning panel ND 11 + 30-2

Uponor Tecto double sided strips

Uponor Tecto pipe fi xation element

Uponor Tecto PE foil for compensation element

Uponor Tecto PE foil for compensation element in 45°

14 — 1714 — 17

Room controls


Control stations


20,5


Uponor edging strip

Manifold/Cabinets

Uponor manifold




Uponor marking set



Uponor cabinet



PE-Xa pipe 14 + 17


MLC press coupling14x2 + 16x2

MLCP pipe 14 + 16


Uponor Tecto - System components and accessories

Uponor pipe positioning panel with insulation ND 30-2Pipe fixing panel ND 30-2 for pipes 14 - 17 mm with heat and sound insulation. Made of expanded polystyrene insulation covered by a black polystyrene foil acc. to DIN EN 13163. DIN EN 13501-1 fire classification: class E. Building-material class B2 conforming to DIN 4102. Approved for moving loads of up to 5.0 kN/m². Thermal resistance: 0.75 m²K/W. For pipe spacing in cm: 10, 15, 20, 25, 30. Dimensions: 1.45 m x 0,85 mPanel height: 52 mm

Item no. h1 [mm] h2 [mm] l [mm] w [mm] A [m²] Δ Lw [dB] Description unit

1005478 52/50 30-2 1450 850 1.12 28 Uponor Tecto pipe positioning panel incl.Insulation for dim. 14-17, thickness 30mm 8.96 m²

Uponor pipe positioning panel with insulation ND 11Pipe fixing panel ND 11 for pipes 14 - 17 mm with heat insulation. Made of expanded polystyrene insulation covered by a black polystyrene foil acc. to DIN EN 13163. DIN EN 13501-1 fire classification: class E. Building-material class B2 conforming to DIN 4102. Approved for moving loads of up to 30 kN/m². Thermal resistance: 0.275 m²K/W. For pipe spacing in cm: 10, 15, 20, 25, 30. Dimensions: 1.45 m x 0,85 mPanel height: 33 mm


1005477 33 11 1450 850 1.12 0 Uponor Tecto pipe positioning panel incl.Insulation for dim. 14-17, thickness 11mm 15.68 m²

> PS-E <b

l h

Uponor compensation insulation element ND 30-2as heat-/sound insulation for use with the compensation element covering foil in door or wall area. Material: Expanded polystyrene hard foam acc. to DIN EN 13163 Building class according to DIN 4102: B2Thermal resistance: 0.75 m²K/W. Approved for moving loads of up to 5.0 kN/m².

Item no. h [mm] l [mm] w [mm] Δ Lw [dB] A [m²] Description unit

1005480 30-2 1400 150 28 0.21 Uponor Tecto compensationinsulation element - thickness 30-2mm 8.4 m

l h

b

> PS

Uponor compensation insulation element ND 11as heat-/sound insulation for use with the compensation element covering foil in door or wall area. Material: Expanded polystyrene hard foam acc. to DIN EN 13163 Building class according to DIN 4102: B2Thermal resistance: 0.275 m²K/W. Approved for moving loads of up to 30 kN/m².

Item no. h [mm] l [mm] w [mm] Δ Lw [dB] A [m²] Description unit

1005479 11 1400 150 0 0.21 Uponor Tecto compensationinsulation element - thickness 11mm 22.4 m




> PS <

bb1

l

l1

Uponor PE-foil for compensation elementFor use with compensation-insulation ND 11 or ND 30-2 in door or wall area, consists of: - covering foil with cutter raster, single overlapping, pipe fixing foil for secure connection of compensation elements on the Tecto elementsMaterial: PS-foilBuilding class according to DIN 4102: B2Colour of leveling foil: black, approx. RAL 9017

Item no. l [mm] l1 [mm] w [mm] w1 [mm] A [m²] Description unit

1005481 1400 1450 200 150 0.21 Uponor Tecto PE-foil forcompensation insulation element 28 m

b

> PS <

Uponor pipe fixation element 45°Consist of 2 pipe fixing naps connected with one pipe fixation element as stripe with 3 fixations for diagonal installation of Uponor pipes on Uponor Tecto pipe positioning panel. Each stripe is separable in 3 fixation elements. Material: Black deep drawing PS foil. Building-material class B2 conforming to DIN 4102.

Item no. w [mm] Description unit

1005482 75 Uponor Tecto pipe fixation elementfor diagonal installation 10 pcs

Uponor PE-foil for compensation element in 45°Covering foil in 45° version for use with compensation-insulation ND 11 or ND 30-2 in door or wall area, consists of: - covering foil with cutter raster, single overlapping, pipe fixing foil for secure connection of compensation elements on the Tecto elementsMaterial: PS-foilBuilding class according to DIN 4102: B2Colour of leveling foil: black, aprox. RAL 9017

Item no. l [mm] l1 [mm] w [mm] w1 [mm] A [m²] Description unit

1005483 1343 1414 225 150 0.2 Uponor Tecto PE-foil forcompensation insulation element in 45° 26.8 m

> PS <

l

h

b

l1

Uponor double-sided stripFoil strips with pipe fixing studs in two rows for the proper connection of Tecto elements ND 11 or ND 30-2 (butt joints)Material: Deep drawn PS foilDIN 4102 building material class: B2Colour of cover foil: traffic black (near RAL 9017)

Item no. l [mm] l1 [mm] w [mm] h [mm] Description unit

1005484 1350 1400 100 22 Uponor Tecto double sided stripsto connect panels 33.75 m

EEI-Int-RHC-01.1216








Uponor eval PE-Xa Q&E pipe in coilsPipes manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method, complying with e.g. EN ISO 15875 ”Plastics piping systems for hot and cold water installations - Cross-linked polyethylene”. Includes an ethylene vinyl alcohol (EVOH) oxygen barrier layer, complying with DIN 4726, to prevent corrosion of system components. This barrier has been specially developed to work together with Uponor Q&E fitting technology. Classification of service conditions (including typical field of application): Application class 4 - Underfloor heating and low temperature radiators, malfunction temperature 95 °C. Design pressure 6 bar. Application class 5 - high temperature radiators, malfunction temperature 95 °C. Design pressure 6 bar.

Item no. d [mm] s [mm] l [m] p [bar] Description unit

1047610 16 2.0 120 6 Uponor eval PE-Xa Q&E pipe16x2.0 mm in coils of 120 m 120 m





1034535 17 2.0 120 0.13 Uponor pe PE-Xa Q&E pipe 17x2.0120 m coil 120 m




















1042389 16 natural Uponor Q&E Ring eval with stop edgenature 16 20 pcs






EEI-Int-RHC-01.1218

Uponor Radiant Heating/Cooling > Uponor self attaching system


Uponor self attaching system

With its self attaching system, Uponor off ers installers an innovating pipe laying system for underfl oor heating pipes. At the factory, hook fasting tape is wound around the oxygen-tight pipes conforming to DIN 4726. The system insulat-

ing panel, which can also be used as a stapler panel, is completely covered with the matching laminated loop foil. The pipe can be reeled off and laid on the fl oor as usual and only needs to be pressed at the correct position against the laminated insulating panel. The hooks on the tape around the pipe catch the loops on the foil and thus secure the pipe to the surface. Both the hook take and the loop foil are designed to guarantee maximum fi xture.

Your advantages Easy pipe laying without any special tools For cost-effi cient one-man installation Installed pipes can be repositioned at any time System panels available in various thicknesses to suit indi-

vidual insulation needs Roll-out insulation for fast installation Ideal for fl exible pipe spacing in rooms of any shape Thanks to the large number of fastening points, the pipe is

fi rmly placed against the surface along its entire length

System components

Uponor self attaching insulation roll panel


Uponor PE-Xa self attaching pipe 16 x 1.8

Uponor MLCP self attaching pipe 16x2.0

Uponor self attaching insulation fold panel

Uponor tape

Room controls


Control stations


20,5


Uponor edging strip

Manifold/Cabinets

Uponor manifold




Uponor marking set



Uponor cabinet


MLC press coupling16x2



Uponor self attaching system - System components and accessories

Uponor self attaching insulation roll panelPipe fixing panel in roll form, for thermal and impact noise insulation according to DIN EN 13163 and DIN 4108-10; made from EPS rigid foam with laminated textile adhesive foil for overlap installation; foil extending on one side to cover insulating layer according to DIN 18560. Foil raster: 100 x 100 mmDIN EN 13501-1 fire classification: class E

Item no. Description unit

1007226 Uponor self attaching insulation roll panel 25-2EPS 045 DES SM 12 m²

1007228 Uponor self attaching insulation roll panel 30-3EPS 045 DES SM 12 m²

Uponor self attaching insulation fold panelPipe fixing panel , for thermal and impact noise insulation according to DIN EN 13163 and DIN 4108-10; made from EPS rigid foam with laminated textile adhesive foil for overlap installation; foil extending on one side to cover insulating layer according to DIN 18560. Foil raster: 100 x 100 mmDIN EN 13501-1 fire classification: class E


1007232 Uponor self attaching insulation fold panel 30-3 10 m²

Uponor self attaching insulation fold panel 15mmPipe fixing panel , for thermal insulation according to DIN EN 13163 and DIN 4108-10; made from EPS rigid foam with laminated textile adhesive foil for overlap installation; foil extending on one side to cover insulating layer according to DIN 18560. Foil raster: 100 x 100 mmDIN EN 13501-1 fire classification: class E


1007234 Uponor self attaching insulation fold panel 15mmEPS 040 DEO 20 m²

Uponor tapeTape for the sealed joining of Uponor insulation, applied with hand-held roll device. Roll length 66m.

Item no. l [m] Description unit

1000012 66 Uponor tape 50 mm 1 pcs

EEI-Int-RHC-01.1220

h [mm] l [mm] w [mm] G [kN/m²] R-value [m²K/W] Δ Lw [dB]

25-2 12000 1000 4 0.56 28

30-3 12000 1000 4 0.67 29


30-3 2000 1000 4 0.67 29


15 2000 1000 30 0.38 -


Uponor self attaching system - System components and accessories

Uponor PE-Xa self attaching pipesPE-Xa pipe with an oxygen diffusion barrier of EVOH manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method complying with DIN 16892 and DIN ISO 15875, oxygen tight according to DIN 4726. Max. operating temperature: 70°CApplication class 4 / 6 bar.


1047624 16 1.8 240 Uponor self attaching eval PE-Xa pipe 16x1.8240 m coil 240 m

1047625 16 1.8 640 Uponor self attaching eval PE-Xa pipe 16x1.8640 m coil 640 m

Uponor MLCP UFH/C self attaching pipesDiffusion-tight multi layer composite pipe (PE-RT - adhesive agent - longitudinally welded aluminium - adhesive agent - PE-RT) for radiant heating / cooling applications. Normally inflammable, materials classification B2 according to DIN 4102. Max. continuous operation pressure: 4 bar at continuous operating temperature 60°C.


1048249 16 2 200 Uponor MLCP self attaching red heating UFH/C 16x2.0200m pipe with oxygen barrier 200 m

1048395 16 2 500 Uponor MLCP self attaching red heating UFH/C 16x2.0500m pipe with oxygen barrier 500 m











Uponor Radiant Heating/Cooling > Uponor stapler and clamp track

EEI-Int-RHC-01.1222

Uponor stapler and clamp track system

All components of the Uponor stapler and clamp track system are designed to perfectly match each other. The panels with thermal and impact noise insulation are equipped with a tear-proof sur-face and a printed installation

grid. They allow for easy installation of the system pipe. These and all other components are designed to ensure optimum safety and reliable operation of the system.

Your advantages Flexible pipe laying Available as composite panels or rolls with a range of diff er-

ent thermal and impact noise insulation layers Suitable for all types of screeds Large pipe coils reel for minimum cut-off s and twist-fee

installation Fast to install thanks to the integrated insulation layer

cover Universal staple nail for pipe thickness of 14 – 20 mm Easy installation with ergonomically designed Uponor

system stapler

System components

Uponor insulation roll


Uponor PE-Xa pipe

Uponor MLCPpipe

Uponor pipe staple nail

Uponor tape

Uponor clamp track

Uponor fastening nail

Uponor stapler

Room controls


Control stations


20,5


Uponor edging strip

Manifold/Cabinets

Uponor manifold




Uponor marking set



Uponor cabinet



MLC press coupling14x2 + 16x2+ 20x2,25


Uponor stapler and clamp track - System components and accessories

Uponor insulation roll panel with texture foilReady-to-lay heat/sound insulation roll, consisting of: tear-resistant texture foil laminated onto 25-2 EPS 045 DES sm as per DIN EN 13163 and DIN V 4108-10 (WLG 045). DIN EN 13501-1 fire classification: class E. Standard flammability, building-material class B2, conforming to DIN 4102. Suitable for use in area between floors, where rooms on either side are heated to same level. With printed-on grid pattern for ease of cutting and alignment. Approved for moving loads of up to 4.0 kN/m². Thermal resistance: 0,56 (m² x K/W).


1000002 Uponor insulation roll panel with texture foiltyp 30-2 12 m²

1000003 Uponor insulation roll panel with texture foiltyp 30-3 12 m²

Uponor PE pattern foil 0.25mm0,25 mm-thick foil with printed on pattern 100 x 100 mm for laying over existing heat/sound insulation and fixation of clamp tracks. Prevents screed from flowing down into the insulating layer.Dimensions: 100 m x 1.03 m


1000015 100 1.03 0.25 Uponor PE pattern foil 0.25mm thicknessfor clamp track fixation 103 m²

Uponor pipe fixing foilMulti-layer reflection and impact foil, designed to improve thermal insulation and distribution; also serving as damping course. With printed raster.Load capacity: 15 kN/m2Roll width: 1 mRoll length: 60 mFoil height: 4 mm

Item no. l [m] w [m] s [mm] G [kN/m²] Description unit

1000017 60 1 4 15 Uponor pipe fixing foil 4 mm 60 m²

Uponor Pipe Clip standardPipe staple "Standard" in blue, loaded into magazine for securing heating-system pipes onto insulation. For Uponor pipes 14 - 20 mm.


1002296 14-20 Uponor Pipe Clip standardØ: 14-20 mm, H = 40 mm 1000 pcs

Uponor Pipe Clip longPipe staple "Long" in grey, loaded into magazine for securing heating-system pipes onto insulation. For Uponor pipes 14 - 20 mm.


1002297 14-20 Uponor Pipe Clip longØ: 14-20 mm, H = 55 mm 300 pcs



30-2 12000 1000 5 0.75 28

30-3 12000 1000 4 0.67 29



ra

d

h

l b

Uponor clamp track 14Self-adhesive U-profile strip made of recycled material, with integrated pipe holder for 14 x 2 mm Uponor pipes. Rated break points are provided every 100 mm for easy separation.Length of track: 2.5 mWidth of track: 38 mmSpace between pipe holders: 50 mm c/cInstallation height with pipe: 17 mm


1005498 2500 38 17 14 50 Uponor clamp track 14 mm 25 m

ra

d

h

l b

Uponor clamp track 16Self-adhesive U-profile strip made of recycled material, with integrated pipe holder for 16 x 2 mm Uponor pipes. Rated break points are provided every 100 mm for easy separation.Length of track: 2 mWidth of track: 40 mmSpace between pipe holders: 25 mm c/cInstallation height with pipe: 25 mm


1013127 2000 40 25 16 25 Uponor clamp track 16 mm 100 m

Uponor clamp track 14-20Self-adhesive U-profile strip made of recycled material, with integrated pipe holder for Uponor pipes 14-20 mm. Length of track: 1 mWidth of track: 50 mmSpace between pipe holders: 50 mm c/cInstallation height with pipe: 27 mm

Item no. l [mm] w [mm] h [mm] c/c [mm] Description unit

1000018 1000 50 27 50 Uponor clamp track 14 - 20 mm 100 m

Uponor fastening nailThe purpose of the fastening nail is to fix the Uponor clamp track and the fixing-foil or the pipe positioning panel to the underlaying layer of insulation. Can also be used for additional manual fastening of Uponor MLC and PE-Xa pipes.


1000019 Uponor fastening nail 500 pcs

EEI-Int-RHC-01.1224






























1013392 20 2.25 200 Uponor MLCP 20x2,25white in coils 200m 200 m


















EEI-Int-RHC-01.1226

Uponor Radiant Heating/Cooling > Uponor pipe positioning panel


Uponor pipe positioning panel 14-16

The Uponor installation panel has been specially developed for the installation of under-fl oor heating/cooling systems in residential and non-residen-tial buildings. The panels are installed in the fl oor below the cement or anhydrite screed

load distribution layer. Uponor installation panels are available in two diff erent thicknesses with insulation (ND30-2) and without insulation (ND11), catering for various fl oor constructions and load-bearing requirements.

Your advantages Cost-effi cient one-man installation Easy laying thanks to large panels (1447 x 900 mm) Compensation elements for doors, movements joints and

wall joints available Suitable pipe sizes from 14 to 16 mm Ensures standardised pipe spacing due to forced pipe paths Proper covering of the insulating layer thanks to integrated

sturdy deep-drawn foil Suitable for a wide range of applications thanks to high

strength properties (ND 30-2: 5 kN/m²; ND 11: 30 kN/m²)

System components Systempipe/-Fittings

Uponor PE-Xapipe

Room controls


Control stations


20,5


Uponor edging strip

Manifold/Cabinets

Uponor manifold




Uponor marking set



Uponor cabinet


Uponor Q&E coupling

MLCP pipe 14 + 16

MLC press coupling14x2 + 16x2

Uponor installation panel 14-16 ND11

Uponor installation panel 14-16 ND

Uponor pipe positioning panel


Uponor pipe positioning panel - System components and accessories

Uponor installation foil 14-16Foil element without foamed back panel. Vacuum-formed PS deep-drawn foil made of impact-proof polystyrene with integrated pipe fixing studs for proper pipe spacing and exact installation of the Uponor system pipes at the required height. The deep-drawn foil overlaps on two sides; when laid in a staggered pattern, the foil layer is thus continuous. For installation on top of insulation layer. Right-angled: RA 5.5 – 11 – 16,5 – 22 – 27.5 – 33 cmDiagonal: RA 7.5 – 15 – 22.5 – 30 cmDimensions of element foil: 1447 x 900 m

Item no. h1 [mm] l [mm] w [mm] A [m²] Δ Lw [dB] Description unit

1016703 18 1447 900 1.2 0 Uponor pipe positioning panel14 - 16 mm 10 m²

Uponor installation panel 14-16 / 30-2For cement and self-levelling cement screeds; allows for right-angled or diagonal pipe installation at 6 plus 4 different pipe distances; for optimised heating pipe installation based on actual room geometry with minimum cut-offs thanks to sophisticated system technology; allows for fast and easy installation of the hard/soft PS rigid foam panels with overlapping foil edges. Meets the requirements for standard impact noise insulation (DIN 4109), thermal insulation (DIN EN1264), DIN EN 13501-1 fire classification: class E, fire safety (DIN 4102) B2 and heat output (DIN EN 1264), irrespective of the pipe spacing; the height and distance of the sturdy pipe holders (DIN EN 1264) are fixed to prevent shifting of the pipes; the overlapping application foil acts as a damp-proofing course and eliminates sound bridges (DIN 18560); protects the environment thanks to use of environmentally friendly PS. Properties subject to continuous RAL quality monitoring.Pipe spacing with right-angle installation: RA 5.5 - 11 - 16.5 - 22 - 27.5 - 33 cmPipe spacing with diagonal installation: RA 7.5 - 15 - 22.5 - 30 cmType: 30-2 mm, for universal use inresidential and commercial buildings up to 5 kN/m2EPS 040 DES sgDimensions: 1447 x 900 mmPlate thickness: 48 mmImpact noise insulation: 28 dBApplication range: up to 5 kN/m2Thermal resistance: R� = 0.75 m2K/W


1016699 50/48 30-2 1447 900 1.2 28 Uponor nap panel 14-16mm incl.Insulation, thickness 30mm 10 m²

EEI-Int-RHC-01.1228



Uponor installation panel 14-16 / 11For cement and self-levelling cement screeds; allows for right-angled or diagonal pipe installation at 6 plus 4 different pipe distances; for optimised heating pipe installation based on actual room geometry with minimum cut-offs thanks to sophisticated system technology; allows for fast and easy installation of the hard/soft PS rigid foam panels with overlapping foil edges. Meets the requirements for standard impact noise insulation (DIN 4109), thermal insulation (DIN EN1264), DIN EN 13501-1 fire classification: class E, fire safety (DIN 4102) B2 and heat output (DIN EN 1264), irrespective of the pipe spacing; the height and distance of the sturdy pipe holders (DIN EN 1264) are fixed to prevent shifting of the pipes; the overlapping application foil acts as a damp-proofing course and eliminates sound bridges (DIN 18560); protects the environment thanks to use of environmentally friendly PS. Properties subject to continuous RAL quality monitoring.Pipe spacing with right-angle installation: RA 5.5 - 11 - 16.5 - 22 - 27.5 - 33 cmPipe spacing with diagonal installation: RA 7.5 - 15 - 22.5 - 30 cmType: 11 mm, for universal use inresidential and commercial buildings up to 30 kN/m2EPS 035 DE0 dm (100kPa)Dimensions: 1447 x 900 mmPlate thickness: 29 mmApplication range: up to 30 kN/m2


1016700 29 11 1447 900 1.2 0 Uponor nap panel 14-16mm incl.Insulation, thickness 11mm 10 m²

Uponor installation panel 14-16 manifold/door kit 30-2For universal use, facilitating pipe laying near manifolds thanks to special manifold element. Stud overlap allows for easy integration into element structure. Door element designed for straight door openings; can be cut into customised door element strips. Per panel, you can cut 10 strips catering for 5 doors. Universal use of element thanks to easy adjustment to complexroom geometries including angled door openings.Type: 30-2 VTEPS 040 DES sgDimensions: 1447 x 900 mmApplication range: up to 5 kN/m2consisting of:2.5 m2 manifold element foil (2 panels)2.5 m2 door element foil (2 panels)5 m2 30-2 mm thermal and impact noise insulation (4 panels)


1016701 50/48 30-2 1420 900 1.2 28 Uponor manifold-/door set for nap panel 14-16mmthickness 30mm 5 m²




For universal use, facilitating pipe laying near manifolds thanks to special manifold element. Stud overlap allows for easy integration into element structure. Door element designed for straight door openings; can be cut into customised door element strips. Per panel, you can cut 10 strips catering for 5 doors. Universal use of element thanks to easy adjustment to complexroom geometries including angled door openings.Type: 11 VTEPS 035 DEO dm (100 kPa)Dimensions: 1447 x 900 mmApplication range: up to 30 kN/m2consisting of:2.5 m2 manifold element foil (2 panels)2.5 m2 door element foil (2 panels)5 m2 11mm thermal insulation (4 panels)


1016702 29 11 1420 900 1.2 0 Uponor manifold-/door set for nap panel 14-16mmthickness 11mm 5 m²











EEI-Int-RHC-01.1230

Uponor installation panel 14-16 manifold/door kit 11






















Uponor Radiant Heating/Cooling > Uponor steel mesh Classic

EEI-Int-RHC-01.1232

Uponor steel mesh system Classic

The Uponor steel mesh system Classic is the ideal solution for underfl oor heating/cooling systems on virtually all fl oors in new residential and com-mercial buildings. Available in three raster sizes, Uponor Classic allows you to

optimise the pipe spacing to meet the actual heating needs. As the heating layer is separated from the insulation layer(s), the system, in combination with high-payload insulation, is also ide-ally suited for areas with high traffi c and payload, such as garage showrooms, production halls, retail outlets, etc.

Your advantages Exact pipe laying: the steel mesh and pipe holders ensure

standardized pipe distances – along both horizontal and vertical.

Sturdy clamping: the pipe clips secure the pipe fi rmly on the carrier element.

No damage to insulation covering Free hand when choosing your insulating material. Cost-effi cient one-man installation: fl exible, fast and easy

to install, saving you time and money.

System components

Uponor steel mesh


Uponor PE-Xa pipe17x2,0 + 20x2,0

Uponor Q&E couplingUponor PE Foil 0.2mmPE-type 200

Uponor calbe tie

Uponor tying wire

Uponor pipe holder clip

Room controls


Control stations


20,5


Uponor edging strip

Manifold/Cabinets

Uponor manifold




Uponor marking set



Uponor cabinet


e.g. can be used with Knauf Floor Screed FE 80

http://www.knauf.de/pdf/bilder/detbl_wmv/f325_e_2008-04.pdf


Uponor Classic - System components and accessories

Uponor Classic steel meshFor stable attachment of pipe fixations and standard installation of underfloor heating pipes. Dim. 2100mm x 1200mm. Material: corrosion protected steel.

Item no. l [mm] w [mm] d [mm] r [mm] A [m²] Description unit

1005084 2100 1200 3 100 2.5 Uponor Classic element 10cmgrid 10 and 20, corrosion protected 25 m²

1005087 2100 1200 3 150 2.5 Uponor Classic element 15cmgrid 15 and 30, corrosion protected 25 m²




Uponor pipe fixing foilMulti-layer reflection and impact foil, designed to improve thermal insulation and distribution; also serving as damping course. With printed raster.Load capacity: 15 kN/m2Roll width: 1 mRoll length: 60 mFoil height: 4 mm

Item no. l [m] w [m] s [mm] G [kN/m²] Description unit

1000017 60 1 4 15 Uponor pipe fixing foil 4 mm 60 m²

Uponor pipe holder clipPlastic clip for fixation of 15-20mm pipes on steel mesh below or equal 6mm.

Item no. Description

1044181 Uponor pipe holder clip for pipes 15-20mmon steel mesh below or equal 6mm 100 pcs

Uponor tying wireFor fastening Uponor pipes on reinforcement steel meshes. Made of steel.250 pcs per bag.


1009222 Uponor tying wire, 150 x 1.25 250 pcs

Uponor cable tieFor fastening Uponor pipes on reinforcement steel meshed.Made of polyamide.

Item no. w [mm] l [mm] Description unit

1005287 5 200 Uponor cable ties, length 200 mmfor the pipe assembly on support mats 100 pcs



Uponor Classic - System components and accessories

















EEI-Int-RHC-01.1234

Uponor Radiant Heating/Cooling > Uponor Plaster Ceiling Cooling


When it comes to managing room temperature with comfort and cost in mind, the Uponor plaster system is truly multital-ented as it can be used in ceil-ings or walls and for cooling as well as heating.

Your advantages Minimum installation height A universal system for ceilings and walls mounting Very few, optimally interacting system components Choice of preference for decades Uponor PE-Xa pipe

9,9 x 1,1 mm Q&E fi tting system for fast,economical installation Quick reaction time thanks to slim plaster coverage Saves energy thanks to optimum operating temperatures

Uponor clamp track

Uponor PE-Xa pipe9,9 x 1,1

Uponor PE-Xa pipe20x2

Uponor Q&ET-reducer 20/9,9/20

Uponor Q&Ejointing reducer 9,9/20

Uponor plaster ceiling cooling system

Systempipe/-Fittings Additional componentsSystem components

Uponor Minitec coupling 9,9

Uponor Minitec expander tool

Room controls


Control stations


20,5

Manifold/Cabinets

Uponor manifold


Uponor cabinet


e.g. can be used with Knauf MP 75 Projection Plaster

http://www.knauf.de/pdf/bilder/detbl_wmv/p111_e_2008-06_ii.pdf


Uponor Plaster Wall/Ceiling H/C - System components and accessories

ra

d

h

l b

Uponor clamp track 9.9Self-adhesive U-profile strip made of recycled material, with integrated pipe holder for 9.9 x 1.1 mm Uponor PE-Xa pipes.Length of track: 2.5 mWidth of track: 24 mmSpace between pipe holders: 20 mm c/cInstallation height with pipe: 13 mm


1005274 2500 24 13 10 20 Uponor clamp track 9.9 mm 25 m














EEI-Int-RHC-01.1236


Uponor Plaster Wall/Ceiling H/C - System components and accessories

Uponor PE-Xa Q&E jointing reducer 20x9.9For connection of Uponor PE-Xa pipes, made of brass.

Item no. d [mm] d1 [mm] Description unit

1020518 9.9 20 Uponor PE-Xa Q&E jointing reducer 20 x 9.9incl. 1 PEX ring 9.9 and 1 PEX ring 20 5 pcs

Uponor PE-Xa Q&E tee reducer 20x9.9x20For connection of Uponor PE-Xa pipes, made of brass.

Item no. d [mm] d1 [mm] d2 [mm] Description unit

1020524 20 9.9 20 Uponor PE-Xa Q&E tee reducer 20 X 9.9 X 9.9incl. 1 PEX ring 9.9 and 2 PEX rings 20 5 pcs











Uponor Radiant Heating/Cooling > Uponor heat emission plate

Uponor heat emission plate

Uponor heat emission plate 17mmMade of aluminium for use with timber suspended floors, with joists at 200mm centres. For support of Uponor PE-Xa pipes 17x2mm.


1009129 1150 190 Uponor heat emission plate 17 mm1150 x 190 mm 60 pcs

Uponor heat emission plate 20mmMade of aluminium for use with timber suspended floors, with joists at 300mm centres. For support of Uponor PE-Xa pipes 20x2mm. Each pack of 40 plates covers 16m² (based on 80% floor coverage).


1009132 1150 280 Uponor heat emission plate 20 mm1150 x 280 mm 40 pcs

EEI-Int-RHC-01.1238

Uponor Radiant Heating/Cooling > Uponor underfloor heating accessories

Uponor underfl oor heating accessories

Uponor edging strip 150x8Edging strip conforming to DIN 18560, made of polyethylene with self-adhesive strip on outer face provides tight seal between edging strip and insulation. Length of roll: 50 m

Item no. h [mm] s [mm] l [m] Description unit

1000079 150 8 50 Uponor edging strip 150x8in length of 50 m 200 m

Uponor edging strip 150x10For installation between screed and adjacent building parts for floor constructions according to DIN 18560 and DIN EN 1264; with multiple tear perforation, laminated PE foil, self-adhesive sealing strips, particularly suitable for self-levelling screeds; bottom side adhesive for attachment to wall and exact installation in wall cornersMaterial: Closed-cell polyethylene PE-LDBuilding material class: B2Colour: blue

Item no. h [mm] s [mm] l [m] colour [-] Description unit

1000080 150 10 50 blue Uponor edging strip 150x10in length of 50 m 200 m

Uponor joint profile 100x10Self-adhesive clamp-on profile element made of hard PVC with polyethylene foam expansion strip, 10 mm thick, for the reliable separation of screed sections (e.g. in doorways), and to absorb expansion of screed. For expansion joints as per DIN 18560-2.Height: 100 mmMaterial thickness: 10 mmLength: 2 m

Item no. h [mm] s [mm] l [m] Description unit

1000081 100 10 2 Uponor joint profile/self-adhesive striplength 2 m, height 100mm, thickness 10mm 30 m

Uponor joint protection 20mmMade of PE-LD, with slit opening, for protection of pipes up to 20 mm in areas of expansion joints. Length: 300 mm

Item no. l [mm] w [mm] s [mm] Description unit

1000082 300 80 5 Uponor joint protection tube for pipesup to 20 mm 30 pcs




l

b

s

Uponor joint protection 9.9mmMade of PE-LD, with slit opening, for protection of pipes up to 9.9 mm in areas of expansion joints. Length: 300 mm

Item no. l [mm] s [mm] w [mm] Description unit

1005269 300 2 35 Uponor joint protection tube forPE-Xa pipes 9.9 x 1.1, length 300 mm 30 pcs




Uponor foil plugFor fixing the foil on insulation. Lenght: 25 mm

Item no. l [mm] Description unit

1000016 25 Uponor foil plug l=25mm 100 pcs

Uponor marking kitFor the marking of a measuring point for dampness measurement in screed, with red marker end. The marker is secured according to DIN 18560 with adhesive tape to the cover layer. The cover layer is not destroyed by the marker. A minimum distance from the measuring point to the nearest heating pipe of 10 cm must be observed.Material requirement: 1 marker per room; for areas larger than 50 m2, more markers are required.Material: Rubber round rod; base made in plastic, with adhesive strip

Item no. h [mm] Description unit

1000083 100 Uponor marking setheight 100 mm 10 pcs

Uponor screed additive VD 450For use as screed and mortar bed additive; improves screed quality thanks to enhanced plasticization and better water retention.Do not use in conjunction with levelling or anhydrite screed!Use for 7 cm screed thickness: approx. 0.2 l/m2Minimum screed covering: 30 mm at 2 kN/m2 or 45 mm at 5 kN/m2 in conjunction with Uponor insulation/system board for 5 kN/m2Curing time: 21 days

Item no. DT [d] Con. [l/m²] Description unit

1000084 21 Uponor screed additive for betterheat conductivity, type VD 450 20 l

EEI-Int-RHC-01.1240

approx. 0.2



Uponor screed additive VD 550For use as screed and mortar bed additive; improves screed quality thanks to enhanced plasticization and better water retention.VD 550 N also ensures that the screed dries faster ((high early strength).Do not use in conjunction with levelling or anhydrite screed!Use for 7 cm screed thickness: approx. 0.2 l/m2Minimum screed covering: 30 mm at 2 kN/m2 or 45 mm at 5 kN/m2 in conjunction with Uponor insulation/system board for 5 kN/m2Curing time: 8 days

Item no. DT [d] Con. [l/m²] Description unit

1000085 8 Uponor screed additive for faster dryingVD 550 N 25 l

Uponor NF anti-freeze agentEthylene glycol-based anti-freeze agent, for use as additive in radiant heating systems with Uponor pipes and standard heating system sealing materials.

Vol. concentration to -20°C: 35%Vol. concentration to -25°C: 40%Vol. concentration to -30°C: 45%

Water volume in pipes (for calculation of mixing ratio):14 x 2: 0.079 l/m17 x 2: 0.13 l/m20 x 2.3: 0.19 l/m25 x 2.3: 0.33 l/m


1005066 Uponor antifreezer up to - 30°Ctype NF 20 l


approx. 0.2

Uponor Radiant Heating/Cooling > Uponor underfloor heating manifolds

EEI-Int-RHC-01.1242

Uponor modular plastic manifold

1009214

1042420

1009215

1005233 14x2 100516816x2 100516917x2 100517020x2 1005171

1034524

1005100

1032702

1042471

1009217

1005605 (230 V)1000138 (24 V)

1006288

Number Item no. Item no. Lloops A B [mm]

3 1030580“ 1030583 150

4 1030581 1035084 200

6 1030582 1030585 300

AWith balancing screw

BWith fl ow meter

Manifold loops 2 3 4 5 6 7 8 9 10 11 12

1042420 Uponor plastic manifold single segment 2 1 1

1030580 Uponor plastic manifold 3 way 1 1 1

1030581 Uponor plastic manifold 4 way 1 1 1 2 1 1

1030582 Uponor plastic manifold 6 way 1 1 1 1 2

1009209 Uponor plastic manifold basic kit 1 1 1 1 1 1 1 1 1 1 1

1009209 (Uponor plastic manifold Basic Kit)


Uponor modular plastic manifolds

Uponor modular plastic manifold with balancing screwPack includes supply and return manifolds made of fibreglass reinforced polyamid. Heating loop connections 3/4 MT euro-cone compatible with Uponor compression adapters. Spacing of individual outlets 50 mm. Manifolds can be joined to make the required number of ports. Uponor actuators can be mounted on the return manifold. In each flow manifold there are balancing valves for adjusting the supply in each loop. Max. operating temperature: 60°C; Max. operating pressure: 6 bar.

Item no. outlets [-] l [mm] Description unit

1030580 3 150 Uponor modular plastic manifoldwith balancing srew, 3 way 1 pcs



Uponor modular plastic manifold with flow meterPack includes supply and return manifolds made of fibreglass reinforced polyamid. Heating loop connections 3/4 MT euro-cone compatible with Uponor compression adapters. Spacing of individual outlets 50 mm. Manifolds can be joined to make the required number of ports. Uponor actuators can be mounted on the return manifold. Supply manifold with adjustable and shut-off inserts (flow meter inspection window with scale of 0 – 4 l/min) for flow adjustment of individual heating loops. Max. operating temperature: 60°C; Max. operating pressure: 6 bar.


1030583 3 150 Uponor modular plastic manifoldwith flow meter, 3 way 1 pcs



Uponor accessories for plastic manifolds

Uponor plastic manifold single segment setFor Uponor plastic manifold with balancing screw for additional heating loop extension. Supply segment with regulating valve, return segment with thermostat upper section incl. cap for locking. Made of fibreglass reinforced polyamid.Max. operating temperature: 60°C; Max. operating pressure: 6 bar.

Item no. MT ["] Description unit

1042420 G 3/4 Uponor plastic manifold single segmentset with balancing screw 1 set

Uponor plastic manifold single segment set with topmeterFor Uponor modular plastic manifold with topmeter for additional heating loop extension. Supply segment with adjustable and shut-off inserts (topmeter inspection window with scale of 0 – 4 l/min) for flow adjustment of individual heating loops. Return segment with thermostat upper section incl. cap for locking. Made of fibre-glass reinforced polyamid. Max. operating temperature: 60°C; Max. operating pressure: 6 bar.


1042471 G 3/4 Uponor plastic manifold single segmentwith flow meter 1 set



Uponor accessories for plastic manifolds

Uponor plastic manifold basic kitFor Uponor modular plastic manifold including brackets, flat sealing screw connection pieces with swivel nut, thermometer and end pieces with air vent, filling and draining tap and a by-pass.

Item no. l [mm] Description unit

1009209 150 Uponor Plastic manifold Basic kitG1" 1 set

Uponor plastic manifold elbow connection setFor connection of supply/return pipes to Uponor modular plastic manifold from the bottom. Made of fibreglass reinforced polyamid. Max. operating temperature: 60°C; Max. operating pressure: 6 bar.


1032702 Uponor plastic manifold elbow connectionset for connection from below 1 set

Uponor hose connection for plastic manifoldFor connection of refill/drainage hose 1/2" to Uponor plastic manifold.


1009214 Uponor hose connection for plasticmanifold to refill and drainage valve 1 set

Uponor plastic manifold retaining ring setFor connection of Uponor plastic manifold single segments to the manifold in case of heating loop connection from top and bottom.


1009215 Uponor plastic manifold retaining ring set 1 set

Uponor flow meter for plastic manifoldFor adjusting the water quantity of the individual heating loops in a range of 0 -4 l/min. Water quantity is indicated in the inspection window. With shut-off function. Made of fibre-glass reinforced polyamid.


1009217 Uponor flow meter 0-4l/minfor Uponor plastic manifolds 1 pcs

EEI-Int-RHC-01.1244


Uponor stainless steel manifolds

Uponor stainless steel manifold with flow meterManifold bar with flat-sealing screw connection and 1" FT with flat gasket, one side with air vent, filling and drain tap, revolvable for pipe connection and a 3/4" stop at the end. Heating loop connections 3/4" MT eurocone according to DIN V 3838 compatible with all Uponor compression adapters eurocone. Spacing of individual outlets 50 mm. Supply manifold with adjustable and shut-off inserts (flow meter inspection window with scale of 0 – 4 l/min) for flow adjustment of individual heating loops. Return manifold with valves incl. cap for locking. Uponor actuators can be screwed directly on the return valves.Fastener with sound-absorbing element included. Without ball valves and Uponor compression adapters. Made of stainless steel.Max. operating temperature: 60°CMax. operating pressure: 6 bar.


1013051 2 195 Uponor stainless steel UFH-manifold 1"with flow meter, 2 way 1 pcs











Uponor stainless steel manifold with balancing screwManifold bar with flat-sealing screw connection and 1" FT with flat gasket, one side with air vent, filling and drain tap, revolvable for pipe connection and a 3/4" stop at the end. Heating loop connections 3/4" MT eurocone according to DIN V 3838 compatible with all Uponor compression adapters eurocone. Spacing of individual outlets 50 mm. Supply manifold with control valves, manual screws for preadjustment of valves by an allen key. Return manifold with valves incl. cap for locking. Uponor actuators can be screwed directly on the return valves. Fastener with sound-absorbing element included. Without ball valves and Uponor compression adapters. Made of stainless steel.Max. operating temperature: 60°CMax. operating pressure: 6 bar.


1013062 2 195 Uponor stainless steel UFH-manifold 1"with balancing screw, 2 way 1 pcs













Uponor manifold accessories

Uponor plastic manifold connection valve kitFor the hydraulic balancing and shut-off of the Uponor plastic manifold, consisting of:- G 1/Rp 1 inlet control valve for the hydraulic balancing and independent shutt-off of the manifold, including hand wheel and display for settings/closingkvs value: 5.4 m3/h

- G 1/Rp 1 return valve for the shut-off of the manifold, including hand wheel and display for closing; adaptable for Uponor plastic manifold actuators.kvs value: 6.4 m3/hIn conjunction with Uponor plastic manifold actuators, the kvs value is 4.8 m3/h.

The connecting valve can be used to control individual zones.

Material: Housing made in brass, hand wheels made in polyamideMax. testy pressure: 10 bar (water)

Item no. l [mm] h1 [mm] z [mm] MT ["] FT ["] A/F [mm] Description unit

1005100 80 50 45 G 1 Rp 1 38 Uponor plastic manifold connection valveG-1/Rp 1 1 set

Uponor ball valveMade of plated brass. With flat-sealing vertical screw connection 1 MT. Length: 60 mm.


1032701 Uponor ball valve 1 MT x 1 FTflat sealing 1 set

Uponor coupling nippleMade of tin-plated brass. Male thread acc.to DIN EN ISO 228-1.


1006641 3/4 Uponor eurocone nipple MLC 3/4MT-3/4MT 10 pcs

l

d IG

SW

Uponor pipe connection PE-Xa 9.9For connection of Uponor PE-Xa pipes 9.9 x 1.1 mm to Uponor manifolds and Uponor connection box, made of brass.

Item no. d [mm] FT ["] l [mm] A/F [mm] Description unit

1005266 9.9 G 3/4 39 30 Uponor PE-Xa pipe connection9.9 - 3/4 FT eurocone and one PE-X ring 10 pcs

EEI-Int-RHC-01.1246


Uponor manifold accessories

Uponor compression adapterCompression adapter made of brass, for connection of Uponor PE-Xa pipes to manifolds. Female thread 3/4"" eurocone acc. to DIN EN ISO 228-1.Material: Brass

Item no. d [mm] s [mm] FT ["] A/F [mm] Description unit

1005168 14 2.0 G 3/4 30 Uponor PE-Xa compression adapter witheurocone, 14x2.0 x 3/4 FT 10 pcs

1057368 16 1.8/2.0 G 3/4 30 Uponor PE-Xa compression adapter witheurocone, 16x1.8/2.0 x 3/4 FT 10 pcs

1005170 17 2.0 G 3/4 30 Uponor PE-Xa compression adapter witheurocone, 17x2.0 x 3/4 FT 10 pcs

1057370 20 1.9/2.0 G 3/4 30 Uponor PE-Xa compression adapter witheurocone, 20x1.9/2.0x3/4 FT 10 pcs

SW

18

5

d

IG

Uponor plated compression adapterMade of plated brass, for connection of Uponor PE-Xa pipes to manifolds. Female thread 3/4" eurocone acc. to DIN EN ISO 228-1.

Item no. d [mm] FT ["] A/F [mm] p [bar] Description unit

1057441 16 G 3/4 30 6 Uponor compression adapter S5.016x1.8/2.0x3/4 Eurocone plated 10 pcs

1057442 20 G 3/4 30 6 Uponor compression adapter S5.020x1.9/2.0x3/4 Eurocone plated 10 pcs

Uponor compression adapter MLC 3/4" euroconeCompression adapter made of brass, union nut and inner sleeve plated. For connection of Uponor MLC pipes to manifolds (eg. Uponor manifold H). Female thread 3/4" eurocone according to DIN EN ISO 228-1. Test safety and no bevelling.

Item no. d [mm] FT ["] Description unit

1058089 14 3/4 Uponor compression adapter MLC 14-3/4FTeurocone metal version 1 pcs




Uponor manifold H capMade of coated brass, with eurocone sealing insert.

Item no. FT ["] Description unit

1014122 G 3/4 Uponor manifold H cap 3/4FT eurocone 10 pcs



Uponor pipe bend support

Uponor pipe bend support plasticMade of impact resistant plastic to support 90° bends.


1047000 9.9 Uponor pipe bend support plastic9.9 mm 50 pcs

Uponor pipe bend supportMade of galvanized steel as bend support for the pipes in the manifold area.


1009004 16 Uponor pipe bend support14-16 mm 50 pcs

1033975 17-18 Uponor pipe bend support17-18 mm 50 pcs

1009233 20 Uponor pipe bend support20 mm 50 pcs

Uponor manifold cabinets

Manifold cabinet concealed versionFor attachment of Uponor manifolds, Uponor controller and Uponor pump control stations on universal rail fixation incl. fixation set. Made of galvanized steel. All visible parts are powder coated in white colour (RAL 9010).Cabinet width (with frame): 555-950mmCabinet installation depth: 120-180mm Cabinet installation high: 820-910mm

Item no. w [mm] h [mm] Description

1046991 555 820-910 Uponor cabinet concealed version, UFH1width 555mm, colour white 1 pcs




EEI-Int-RHC-01.1248


Uponor manifold cabinets

Manifold cabinet on-wall versionFor attachment of Uponor manifolds, Uponor controller and Uponor pump control stations on universal rail fixation incl. fixation set. Made of galvanized steel. All visible parts are powder coated in white colour (RAL 9010).Cabinet width (with frame): 555-950mmCabinet installation depth: 160mm Cabinet installation high: 820mm

Item no. w [mm] h [mm] Description

1046996 555 820 Uponor cabinet on-wall version, UFH1width 555mm, colour white 1 pcs





Uponor Radiant Heating/Cooling > Uponor controls

EEI-Int-RHC-01.1250

Uponor individual radio room temperature control with Dynamic Energy Management (DEM)

The Uponor individual radio room temperature control system with DEM has been developed on the basis of the existing individual radio room temperature control. Apart from the colour of the controller (previously white, now grey), there are many more diff erences between the two versions. The advanced sys-tem comes with a range of features that make installation even easier. Apart from the great energy effi -ciency during operation, fast instal-lation and user-friendly operation that are standard features of all Uponor systems, the new individual room temperature control makes

heating and cooling even more comfortable.

The automatic balancing function does away with time-consuming manual hydraulic balancing. In most cases, there is no need for recalcu-lation of the valve settings, which is normally required aft er a change of the room layout or the fl oor cover-ing. The heat distribution in the room is evaluated by a bespoke soft ware solution. The relevant val-ues are stored and the system is automatically balanced at regular intervals. This guarantees optimum energy distribution!

The comfort setting prevents that heating surfaces become too cool when the room is heated with an alternative source (e.g. open fi re-place). The supply diagnosis moni-tors the heat performance in all rooms and signals any insuffi cient or excess supply to the I-76 inter-face. The room bypass function is particularly suitable for systems with specifi c minimum fl ow require-ments. Incorrectly assigned thermo-stats are automatically detected and rectifi ed by the room check func-tion.

Your benefi t

Energy savings up to 12 % thanks to greater effi ciency

No need for manual hydrau-lic balancing

High time saving during installation

More accurate and faster control, up to 25% faster response time

Higher comfort through improved heat distribution

Easy to operate Reliable operation with

minimum support No need for recalculation af-

ter change to heating circuit layout/size

System not aff ected by subsequent change of fl oor covering

Easy troubleshooting "Clean solution" for renova-

tion Remote control via SMS con-

nection possible Easy, well-tried handling Optional automatic switch

over to heating-/ or cooling mode with the Uponor heat-ing/cooling controller C-46

Operation of up to three controller C-56 from one interface I-76

Uponor radio controller (consisting of controller and interface)Item no. 1045562

Uponor radio thermostat T-75Item no. 1000502 (white)Item no. 1000504 (silver)Item no. 1046114 (grey)

Uponor radio controller C-56(for system extension)Item no. 1045565

Uponor thermostat T-54Item no. 1045572

Uponor SMS-module R-56Item no. 1045570

Uponor interface I-76Item no. 1045568

20,5

20,5


Uponor Radio control

Uponor controller with interface C-56+I-76 radioFor receiving and transforming of radio signals from the thermostats, with integrated DEM functionsconsisting of:Controller C-56 with- Electronic control- Reception of max. 12 room-thermostats- Connection of max. 14 actuators 24 Volt- Heating/Cooling function switched by external contact- Pump relay- Valve exercise, pump exerciseInterface I-76 with- Display, back lighted, new look, blue full dot matrix- Menu in English,Integrated functions:- Five temperature setback progams,- Max/min temperature limitations, - Holiday temperature- Automatic summer/wintertime change- Auto adapt function- Room check function- Room bypass function- The Interface can control up to 3 controllersAccessoriesExternal Antenna, cables for connections, mounting materialMark of conformity: CEOperational voltage: 230 V / 50 HzMax. power input per actuator: 0,2 AProtection class: IP 30 (EN 60 529)Colour: grey (RAL 7015)

Item no. OV [V] P [W] EP/a [W] colour [-] Description unit

1045562 230 1 >2 grey Uponor controller with interfaceC-56+I-76 radio, grey 1 set

316 60

110

50 20

24 V

Uponor controller C-56 radioFor receiving and transforming of radio signals from the thermostats, to use the DEM function with the I-76.consisting of:Controller C-56 with- Electronic control- Reception of max. 12 room-thermostats- Connection of max. 14 actuators 24 Volt- Heating/Cooling function switched by external contact- Pump relay- Valve exercise, pump exercise- Plastic color grey (RAL 7015)- Protection rating IP 30AccessoriesExternal Antenna, cables for connections, mounting material

Item no. OV [V] P [W] EP/a [W] colour [-] Description unit

1045565 230 1 >2 grey Uponor controller C-56 radiogrey 1 pcs




Uponor interface I-76For combination with the controller C-56 to use the DEM functionInterface I-76 with- Display, back lighted, new look, blue full dot matrix- Menu in English,Integrated functions:- Five temperature setback progams,- Max/min temperature limitations, - Holiday modus- Automatic summer/wintertime change- Auto adapt function- Room check function- Room bypass function- For controling of up to 3 controllersProtection class: IP 30 (EN 60 529)Colour: grey (RAL 7015)

Item no. l [mm] w [mm] h [mm] Description unit

1045568 110 110 30 Uponor interface I-76grey 1 pcs

Uponor thermostat display T-75 radioDesigned as a wireless single room temperature sensor, measuring the perceived room temperature and transmitting the values to the wireless base unit or wireless control module, with display showing the set and measured room temperature, consisting of:

Housing with - Temperature programming buttons- Control electronics

Signal range: max. 30 m Signal frequency: 868 MHzPower supply: Alkaline battery, service life approx. 5 years, size AAATransmission power: approx. 1 mW Set temperature range: 5 - 30 °CColour: pure white (near RAL 9010) or silver (near RAL 9006)

Item no. l [mm] w [mm] h [mm] colour [-] Description unit

1000502 124 66 16 white Uponor thermostat display T-75 radiowhite 1 pcs

1000504 124 66 16 silver Uponor thermostat display T-75 radiosilver 1 pcs

1046114 124 66 16 grey Uponor thermostat display T-75 radiogrey 1 pcs

Uponor thermostat mounting kitAccessory for wireless room sensor; use this kit to position and/or secure the room sensor anywhere in the room on the wall; with removal/child safety device, consisting of:

- Mounting plate with clip- Bracket- Adhesive pads for fixture to smooth surfaces (tiles, etc.)

Colour: pure white (near RAL 9010) or silver (near RAL 9006) or grey

Item no. colour [-] Description unit

1000503 white Uponor thermostat mounting kitfor T-75 radio, white 1 pcs

1000505 silver Uponor thermostat mounting kitfor T-75 radio, silver 1 pcs

1046115 grey Uponor thermostat mounting kitfor T-75 radio, grey 1 pcs

EEI-Int-RHC-01.1252



Uponor thermostat T-55 radioRadio thermostat, including batteries and screws for mounting. Operating distance: max. 30 m. Set point range 6 – 30°C.


1000527 72 72 21 Uponor thermostatT-55 Radio 1 pcs

Uponor thermostat public T-54Radio thermostat with inside setting, including batteries and screws for mounting. Operating distance: max. 30 m. Set point range 6 – 30°C. SMS module R-56 can be connected.Floor sensor for min/max limitation of floor temperature can be connected.


1045572 72 72 21 Thermostat PublicT-54 Radio 1 pcs

Uponor SMS module R-56For connection with the thermostat T-54, to activate and control the system settings and monitor the actual room temperature in a reference room via SMS.


1045570 185 75 28 Uponor SMS moduleR-56 1 pcs

Uponor floor sensorFloor sensor for connection to the thermostats (radio and wired) with external input with sensor attached to 4m cable.

Item no. d [mm] l [mm] l1 [mm] Description unit

1000538 5 4000 25 Uponor floor sensorfor T-33, T-37 1 pcs



Uponor outdoor sensor

Uponor outdoor sensorOutdoor sensorfor connection to the Thermostats with external inputwith Sensor box and seperate 5 m cableHas to be connected to thermostat T-54 in a system with Interface I-76 to display outdoor temperature.- IP65- Plastic color 7035

Item no. colour [-] Description unit

1000529 Uponor outdoor sensorfor T-33, T-37, T-53 1 pcs

Uponor installation cableTwisted pairs cable to connect:- Interface to Controller- Controller to Controller- Extension for Antenna cable

Item no. l [m] Description unit

1000515 15 Uponor installation cable15m 1 pcs

Uponor repeaterTo solve problems with radio transmission, for on-wall mounting.

Item no. OV [V] P [W] l [mm] w [mm] h [mm] Description unit

1000518 230 < 1 160 75 26 Uponor repeater230 V 1 pcs

Uponor KNX media coupler R-76can connected the C-56 Radio to a standard KNX bus. This device will act as a interface between the C-56 Radio and the KNX wired bus.

Conformity: CEProtection Class: IP 30


1045571 203 75 26.5 KNX Media CouplerR-76 1 pcs

EEI-Int-RHC-01.1254

light grey



Uponor 24 V individual room climate control system

Wired individual room tempera-ture control system with wide range of components.

The Uponor 24 V individual room climate control system consists of electronic components that have been specially devised for combina-tion with each other (3 thermostat models, 2 controllers and optional timer). As soon as a thermostat detects that heating or cooling in a room must be adjusted, the con-troller operates the 24 V thermo drives accordingly. The three ther-

mostat models available for this system can be freely combined with each other and are connected to the controllers through non-polari-ty 2-core cables (6-12 V) that can-not be confused.

Choose between two controller types

Depending on the size of the heat-ing system and the specifi c require-ments, you can install a 6-channel (C-33) or 12-channel (C-35) con-troller.

The 12-channel controller caters for maximum 12 thermostats and 14 thermal actuators plus an optional timer I-36. The 12-channel C-35 controller also provides the option to switch over between heating and cooling.

The device is wired in such a way that several thermal actuators can be com-bined with a single thermostat with-out the need for wired bridges. Ther-mostats and thermal actuators are connected to the controller through easy-to-use plug-in wiring terminals.

Your benefi t

Low-cost and safe thermo-stat wiring (6-12 V)

Choice of three thermostat models

Connection of optional fl oor sensors

Room temperature lowering with Uponor timer and two timer zones

Optional limitation of set point temperature settings

Also suitable for surface cooling systems with dew point monitoring

Optional automatic switch-ing over between heating/cooling with Uponor heat-ing/cooling controller C-46

Important:

The Uponor 24 V individual room climate control system is a stand-alone system of tailor-made components that cannot be replaced with third-party devices.


Uponor wired control

Uponor controller C-33, 6 channelsController C-33 with electronic control, connection of max. 6 Thermostats, connection of max. 8 actuators 24 Volt, pump relay, pump / valve exercise, power LED, plastic color RAL 9010, protection rating IP 30, accessories, mounting material.

Item no. OV [V] l [mm] w [mm] h [mm] Description unit

1000531 24 315 110 58 Uponor controller, 6 channelsC-33 wired 1 pcs

Uponor controller C-35, 12 channelsFor the power supply of max. 12 room sensors (models T-33,T-35, T-37) and max. 14 thermo drives (models TA/TR),24 V. Preassembled unit, consisting of:

- Housing including mounting accessories- Control electronics with microprocessor- Pump logics- Valve interval- Overload protection- Connecting cable with Euro standard plug

- Floating heating/cooling switching by external signal- Connection port for Uponor I-35 timer with 2 temperature lowering programs and for Uponor dew point converter

Conformity: CEColour: pure white (near RAL 9010)Protection class: IP 30 (EN 60529)Max. power consumption per TA 24: 0.2 A (switching peak)Effective power per TA 24: <2 W


1000533 24 315 110 58 Uponor controller, 12 channelsC-35 wired 1 pcs

Uponor Thermostat T-34Wired flush mounted thermostat for room temperature control

Consisting of:- Flush thermostat T34 with - Dial for settings - Sensor for air temperature - LED for indication - Two wires - Plastic color RAL 9010

General functions- Setpoint range 6-30°C- Setting range can be limited mechanically by moving pins under the dial


1048010 81 81 14.7 Uponor thermostat flush T-34 wired 1 pcs

EEI-Int-RHC-01.1256



Uponor thermostat T-35For connection to Uponor controller C-33 or C-35 with:- Dial for settings- Sensor for air temperature- LED for indication- Two wires- Plastic color RAL 9010

Functions- Setpoint range 6-30°C, mark at 21°C- Setting range can be limited mechanically by moving pins under the dial


1000535 72 72 21 Uponor thermostatT-35 wired 1 pcs

Uponor thermostat T-37 for external sensorFor connection to Uponor controller C-33 or C-35 with: - Dial for settings- Sensor for air temperature- LED for indication- Terminal for Floor Sensor- Two wires- Plastic color RAL 9010

Functions- Setpoint range 6-30°C, mark at 21°C- Setting range can be limited mechanically by moving pins under the dial- Internal setting for the Floor Senor, range print on circuit board


1000536 72 72 21 Uponor thermostat f. external sensorT-37 wired 1 pcs

Uponor wall frameWall frame to cover standard wall boxes or in case of renovation shades of old thermostats, size 90*90, plastic color RAL 9010


1000539 90 90 8 Uponor wall framefor T-33, T-35, T-37 1 pcs




Uponor digital thermostat T-36Consisting of:- Digital thermostat T36

Options:- Floor sensor (1000538) (sold seperately)General functions- Room temperature regulation with internal sensor - Room or remote temperature display- Room temperature, Room and max/min floor temp (heating/cooling) , remote sensor regulation selectable. - Automatic or Manual balancing - Comfort / ECO mode. - Lock indication- Standby/OFF mode- Modes displayed on LCD: Heating, Cooling, ECO, Lock, Standby, Comfort/ECO, Auto/Man balancing.- Displayed temperature calibration- Window open function- 3 button keyboard +/-/OK - Hidden reset


1048011 85 83 25 Uponor digital thermostat T-36 wired 1 pcs

Uponor programmable digital thermostat T-38Consisting of:- Programmable digital thermostat T38

Options:- Floor sensor (1000538) (sold seperately)

General functions - Room or remote temperature display. - Room temperature, Room and max/min floor temp (heating/cooling) , remote sensor regulation selectable. - Automatic or Manual balancing - Comfort / ECO mode. - Lock indication. - Standby/OFF mode - 4 Pre pre-recorded modifiable programs for working days / week-end / week - Date and time, with summer/winter change, power failure proof - Hidden reset - Temporary or permanent override mode

- Modes displayed on LCD: Heating, Cooling, Lock, Standby, Holiday, Comfort/ECO - Displayed temperature calibration - Window open function - Powered by base unit (no batteries)


1048012 85 83 25 Uponor programmable digital thermostat T-38 wired 1 pcs

EEI-Int-RHC-01.1258



Uponor thermostat Public T-33For connection to Uponor controller C-33 or C-35 with:- Plain cover- Internal setting- Sensor for air temperature- Terminal for Floor Sensor- Two wires- Plastic color RAL 9010

Functions- Setpoint range 6-30°C, mark at 21°C- Internal setting for the Floor Senor- Room sensor- Max/min limitation with floor sensor


1000537 72 72 21 Uponor thermostat publicT-33 wired 1 pcs

Uponor timer I-36Consisting of:- Programmable digital timer I36

General functions - 2 zones programming comfort / ECO - Display of zone status and time - Pre-recorded modifiable programs for working days / week-end / week - Date and time, with summer/winter change, power failure proof - Lock mode, standby OFF mode - Hidden reset - Temporary or permanent override mode - Dry contact input for forced ECO mode. - Example: Signal from Uponor R-56 SMS module for remote control - Powered by base unit (no batteries)


1048013 85 83 25 Uponor timer I-36 for C-35 1 pcs

Uponor control accessories 24 V

Uponor actuator 24V24 V, with open/closed indicator, suitable for use with Uponor plastic manifolds in connection with Uponor radio or wired control system. Closes when idle. With all-round shower protection (IP 54). Suitable for operation at ambient temperature of up to 60°C. Threaded connector M 30 x 1.5 mm MT.Height: 54 mm.

Item no. MT [-] d [mm] h [mm] OV [V] P [W] Description unit

1000138 30x1.5 40 54 24 < 2 Uponor actuator 24V for plasticmanifold, 30 x 1,5 MT 1 pcs

Uponor actuator 24V24 V, with open/closed indicator, suitable for use with Uponor stainless steel manifolds in connection with Uponor control system. Closes when idle. With all-round shower protection (IP 54). Suitable for operation at ambient temperature of up to 60°C. Threaded connector M 30 x 1.5 mm FT.Height: 56 mm

Item no. FT m [-] d [mm] h [mm] OV [V] P [W] Description unit

1013008 30x1.5 40 56 24 ~ 2 Uponor actuator 24V for stainlesssteel manifold, 30 x 1,5 FT 1 pcs




Uponor return temperature limiterFor use in low-temperature range for combined underfloor/ radiator heating systems respectively wall-radiator heating systems for the regulation of the return temperature of small heating areas up to max. 15 m2. Consists of installation casing with cover, fast-action air vent valve, thermostat for return temperature limiting set between 25 and 65 °C. Factory-made limitation of return temperature approx. 50°C. Suitable for Uponor compression adapter with 3/4" eurocone.Dimensions: (H x W x D) 150 x 122 x 65 mm D after installation: 5 mm


1013005 Uponor return temperature limiter 1 pcs

Uponor wired control 230 V

Uponor Controller C-23Uponor Controller C-23 for wiring up to 6 room thermostats and max. 14 actuators. Up to 4 actuators per channel are possible.Optional: pump relay. IP43.

Item no. l [mm] w [mm] h [mm] OV [V] Description unit

1058426 310 90 65 230 Uponor Controller C-23230V, WIRED 1 pcs

Uponor Pump Relay for Controller C-23Pump relay for C-23 6 room Controller


1058427 310 90 Uponor Pump Relay for Controller C-23230V, WIRED 1 pcs

Uponor Thermostat T-23Standard Thermostat 230 V, with on/off contact


1058422 Uponor Thermostat T-23230V, WIRED 1 pcs

Uponor Thermostat Flush T-24Flush Mounted Thermostat 230 V. On/off contact, insulated cover, protective cap, frame (neutral), 50 x 50 mm cover, pure white , glossy


1058423 Uponor Thermostat Flush T-24230V, WIRED 1 pcs

EEI-Int-RHC-01.1260


Uponor wired control 230 V

Uponor Thermostat H/C T-25Heating/Cooling Thermostat 230 V with a change over contact for maximum 5 actuators and a heating / cooling switch. For 2 pipe installation, specially for heatpump.


1058424 Uponor Thermostat H/C T-25230V, WIRED 1 pcs

Uponor Thermostat Prog. Digital T-26Digital Programmable Thermostat 230V. Energy saving feature calculates heat up time of system. Includes holiday mode, temporary over-ride and specified duration, 5/2 or 7 day programme, floor temperature control, lock facility, status display on current thermostat mode.


1058425 Uponor Thermostat Prog. Digital T-26230V, WIRED 1 pcs


Uponor actuator 230 V230 V, with open/closed indicator, suitable for use with Uponor plastic manifolds. Closes when idle. With all-round shower protection (IP 54). Suitable for operation at ambient temperature of up to 60°C. Threaded connector M 30 x 1.5 mm MT.Height: 54 mm.

Item no. MT [-] d [mm] h [mm] OV [V] P [W] Description unit

1005605 30x1.5 40 54 230 < 3 Uponor actuator 230V for plasticmanifold, 30 x 1.5 MT 1 pcs

Uponor actuator 230 V230 V, with open/closed indicator, suitable for use with Uponor stainless steel manifolds. Closes when idle. With all-round shower protection (IP 54). Suitable for operation at ambient temperature of up to 60°C. Threaded connector M 30 x 1.5 mm FT.Height: 56 mm

Item no. FT m [-] d [mm] h [mm] OV [V] P [W] Description unit

1013006 30x1.5 40 56 230 ~ 3 Uponor actuator 230V for stainlesssteel manifold, 30 x 1,5 FT 1 pcs



EEI-Int-RHC-01.1262

Uponor Controls

Heating-supply temperature control with radio individual room temperature control

Functional descriptionThe wireless room temperature sensor measures the operative room temperature. Through the wireless con-troller, the thermal actuators and manifold valves, it controls the heat release from the respective room heat-ing surface. The wireless basic control unit allows for

The diagram shows a simplifi ed illustration of the key control components. For detailed instruc-tions regarding the installation and operation of the system, refer to the manuals shipped with the components or download the relevant documents from www.uponor.com.

Components1 Radio controller C-56 with interface I-762 Radio controller C-563 Antenna4 Wireless thermostat5 Climate controller C-466 Supply/return sensor7 Outdoor sensor8 Manifold9 heating source

4

6 6 5

1

4

2 x 0,5 mm2

max. 20 m(je Verbindung)

4

2

2 x 0,4 mm2

max. 50 m

7

23 3

9

3

M

99

8

individual room temperature control. It is thus for exam-ple possible to assign diff erent temperature lowering times to diff erent rooms. Together with the remote con-trol system, the C-46 heating controller adjusts the sup-ply temperature depending on the actual weather con-ditions and the programmed heating times.



heating/cooling - supply temperature control with automatic H/C switchover valve powerd by boiler and chiller

Functional descriptionDepending on the outdoor and room temperature, the C-46 heating/cooling controller switches the switch-over valve installed by the operator from the heating to the cooling source. The H/C switching module switches the C55/C56 wireless controller from heating to cooling mode, as the manifold valves must be opened as the room temperature increases (reverse operation of ther-mal actuators). For cooling, the relative air humidity in the room must also be measured, in addition to the room temperature. This is done through the humidity sensor H-56. It is important to prevent that the temper-

The diagram shows a simplifi ed illustration of the key control components. For detailed instruc-tions regarding the installation and operation of the system, refer to the manuals shipped with the components or download the relevant documents from www.uponor.com.

Components1 Radio controller C-56 with interface I-762 Radio controller C-563 Antenna4 Wireless thermostat5 H/C relay6 Climate controller C-467 Supply/return sensor8 Outdoor sensor9 Chiller

10 Switch-over valve

ature drops below the dew point, as this would lead to condensation on cold system components. The C-46 heating/cooling controller regulates the cooling water supply temperature through the control valve to keep it above the dew point temperature. This ensures that the system components from the control valve downwards are protected against damage from condensation that tends to occur when the actual temperature drops below the dew point. Depending on the cooling water temperature, the system components from the chiller to the control valve must be insulated with diff usion-tight material.

4

7

9

7 6

1

4

2 x 0,5 mm2

max. 20 m2 x 0,5 mm2

max. 20 m(je Verbindung)

4

2

2 x 0,4 mm2

max. 50 m

8

23 3

10

3

M

100 m (vom Elektrofach-betrieb zu prüfen)


Uponor climate controller

Uponor climate controller C-46Weather compensator controlling supply water in heating.Can be integrated in the C-56 system via bus connection.Consisting of:- Climate Controller C-46- Wired Outdoor sensor- Wired Supply sensor

Options:- Antenna Module for connection to wireless Thermostats- Wired Indoor sensor- Wired Return sensor.

General functions- Installation wizard gives easy and fast installation & set-up- Quick menu system gives easy access to basic settings- Integration with C-56 system via bus gives CC access to zone data from C-56.- System information, H/C-state, ECO-mode etc are also shared on the bus.- Automatic summer/wintertime change- ECO/Comfort timer in CC if no I-76 in the system.- Clock backup 8 hours- Alarm at disturbance- Pumpmanagement with internal fuse- Supports 24V Thermal Actuator or 0-10V controlled rotating mixer motor, or variable speed pump- General purpose input for Heating+Cooling switch or Snow detection- General purpose output for Heating+Cooling command or Dehumidification command or Error signalling- Input indoor sensor- Input outdoor sensor- Input Supply Sensor- Input Return SensorAccessoriesOutdoor sensor (5m cable), Supply sensor (4m cable), mounting material


1047844 174 106 80 Uponor climate controller C-46 1 pcs

EEI-Int-RHC-01.1264



Uponor climate controller C-46 extendedWeather compensator controlling supply water in heating + coolingCan be integrated in the C-56 system via bus connection.

Consisting of:- Climate Controller C-46- Antenna- Wireless Humidity Sensor H-56- Wired Outdoor sensor- Wired Supply sensor

Options:- Wired Indoor sensor- Wired Return sensor- Additional 5 RH-sensors

General functions- Installation wizard gives easy and fast installation & set-up- Quick menu system gives easy access to basic settings- Integration with C-56 system via bus gives CC access to zone data from C-56.- System information, H/C-state, ECO-mode etc are also shared on the bus.- Automatic summer/wintertime change- ECO/Comfort timer in CC if no I-76 in the system.- Clock backup 8 hours- Alarm at disturbance- Pumpmanagement with internal fuse- Supports 24V Thermal Actuator or 0-10V controlled rotating mixer motor, or variable speed pump- General purpose input for Heating+Cooling switch or Snow detection- General purpose output for Heating+Cooling command or Dehumidification command or Error signalling- Input indoor sensor- Input outdoor sensor- Input supply sensor- Input return sensor

Humidity Sensor H-56:- Wireless RH sensor with battery alarm- incl Batteries and mounting kit- Connects to C-46 with antenna or via C-56

AccessoriesOutdoor sensor (5m cable), Supply sensor (4m cable), mounting material , 3m Antenna cable


1047845 174 106 80 Uponor climate controller C-46 extended 1 pcs

Uponor humidity sensor H-56- Wireless RH sensor with battery alarm- incl Batteries and mounting kit- Connects to C-46 with antenna or via C-56


1047846 72 72 21 Uponor humidity sensor H-56 1 pcs




Uponor supply or return sensor for C-46- For connection directly to C-46- Sensor with 4m wire.Note: Return sensor only needed for average temperature control


1047847 Uponor supply or return sensor for C-46 1 pcs

Uponor outdoor or indoor sensor for C-46- For connection directly to C-46- Additional connection wire needed.


1047848 Uponor outdoor or indoor sensor 1 pcs

Uponor relay H/C, 24 VFor automatic heating/cooling switchover on external signal.


1000516 24 160 50 95 Uponor relay H/C24 V 1 pcs

1000517 230 160 50 95 Uponor relay H/C230 V 1 pcs

Uponor Mixer MotorFor mounting on a mixing valve and used in combination with the C-46. Externally powerd.


1002356 Uponor Mixer motor 24Vwith 0-10V signal 1 pcs

1002357 Uponor Mixer motor 230V / 3PT 1 pcs

Uponor Wall Power Supply230V/24V Power supply with Euro-plug for 0-10V controlled mixer motor.


1048763 Uponor Power supply 230V/24Vfor C-46 mixer motor 1 pcs

EEI-Int-RHC-01.1266



Uponor control stations for heating/cooling

UFH systems

RS2Uponor room control stationRS 2 up to 2 kW

Unit set 6Uponor constant tempera-ture control unit set 6up to 6 kW

Push 23Uponor pump groupup to 10 kW

MPG 10Uponor pump group3 to 10 kWwith controller

Unit set type 1Uponor pump groupup to 12 kW

CPG 15Uponor central pump group3 to 15 kWwith controller

Control stations

Minitec

Siccus

Tecto

Self attach-ing system

Tacker & Clamp track

Pipe positi-oning panel

Classic


Uponor control stations

Uponor room control station RS 2Pumpgroup for control of UFH in single rooms, with brass-housing, bracket for front-or backside installation, integrated pump grundfos UP15-14B, venting screw, secondary max.- limiter 25-55°C, balancing valve, actuator 230V,

1-3 kWmax. 90° primary, max. 55° secondary, max. 10 barvalve kvs 1,25 m³/hPump 15-40 for 0,1-0,45 ³/h 1,2-03, m, 230V, 30W,

connection:secondary loop 3/4"" euroconeprimary valves with clampconnection for CU-Pipe 15mmPump needs 230V pump power supply with external switch.

connectible to electrical thermostats no. 1000132

calculation example for Rl,B 0,05m²K/W (tiles)pipe 9,9x1,1 100mm 2 loops a' 60m, =2x 6m² 0,96kWpipe 14x2 150mm 2loops a' 60m = 2x 9m² 1,8 kWpipe 17x2 150mm 2loops a' 90m = 2x14m² 2,8 kWpipe 20x2,0 150mm 2loops a' 105m = 2x16m² 3,2 kW

Item no. Q [kW] l [mm] w [mm] h [mm] c/c [mm] c/c1 [mm] Description unit

1005576 2 360 145 80 60 40 Uponor Room control unit RS 2up to 2 kW with actuator 230V FT 1 pcs

G 3/4

G 3/4 G 3/4

ra

l

Uponor branch connectionFor extension of RS 2 room control station to 2 heating circuits; direct connection of heating circuit G 3/4 fitting with Euro coneEach kit includes 2 fittings.Material: Brass

Item no. l [mm] c/c [mm] Description unit

1005675 50 40 Uponor branch connection for connectionof two loops to Uponor RS 2 1 set

Uponor Push 23Pumpgroup with thermostat and pump energy efficiency class A,

Thermostat with capillary sensor 20-55°C for supply temp.,Pump Grundfos Alpha2L 15-60 0,1-2,4 m³/h, H: 4-0,9 msupply thermostat valve kvs 0,9 m³/hreturn balancing valve kvs 2,0 m³/hsecondary connections G1A for connection to uponor UFHC manifolds,

10 kWmax. 90° primary, max. 55° secondary, max. 10 bar


1046870 Uponor push 23 A, pump and mixing groupfor constant temperature control 1 pcs

EEI-Int-RHC-01.1268



Uponor Manifold Pump Group MPG 10Pumpgroup for connection to Uponor UFHC-manifolds, installation with manifolds on-wall or in cabinets,pre-mounted with supply temperature control C-46 with integrated interface to uponor single room control C-56

3-way-mixing valve, motor drivekvs 4,0pump energy efficiency class A (Grundfos alpha2L 25-60)0,1 - 2,5 m³/h H: 6,0-1 mproportional pressure control

primary ballvalves, connection Rp1 (FT)secondary connection G1A (MT)supplytemperature sensoroutdoor temperature sensor (install. on buildingsite)

3-10 kWmax. 90° primary, max. 60° secondary, max. 10 bar


1048780 Uponor Manifold Pump Group MPG 10with controller 1 pcs

Uponor Manifold Pump Group MPG 10 without controllerto connect to uponor UFHC-manifolds, installation with manifolds on-wall or in cabinets,without actuator, without control ,for connection to external boiler control or connection to Uponor climate controller C-46 heating/cooling, requires Motor 1002356 or 1002357

3-way-valve mixingkvs 4,3pump energy efficiency class A (Grundfos alpha2L 15-60)Q: 0,1-2,5 m³/h, H: 6-2,4 mproportional pressure control

connection G1A secondaryball valve+balancing valve primaryfor installation left or right of manifold

3-10 kWmax. 90° primary, max. 60° secondary


1048781 Uponor Manifold Pumpgroup MPG 10without controller 1 pcs




Uponor Central Pump group CPG 15Pumpgroup for installation in boiler rooms or on-wall with Uponor UFHC-manifolds, pre-mounted with supply temperature control C-46 with integrated interface to Uponor single room control C-56

3-way-mixing valve, motor drivekvs 6,3pump energy efficiency class A (Grundfos alpha2L 25-60)0,1 - 2,5 m³/h H: 6,0-1 mproportional pressure control

primary ball valves, connection Rp1 (FT)secondary connection G1A (MT)supply temperature sensoroutdoor temperature sensor (install. on buildingsite)



1048782 Uponor Central Pump group CPG 15with controller 1 pcs

Uponor Central Pump group CPG 15 without controllerinstallation in boiler rooms , without actuator, without control ,for connection to external boiler control or connection to Uponor climate controller C-46 heating/cooling, requires Motor 1002356 or 1002357

3-way-mixing valve, for motor drive 1002356 or 1002357kvs 6,3pump energy efficiency class A (Grundfos alpha2L 15-60)Q: 0,1-2,5 m³/h, H: 6-2,4 mproportional pressure control

primary connection Rp1 (FT)secondary ballvalves, connection Rp1 (FT)



1048783 Uponor Central Pumpgroup CPG 15without controller 1 pcs

EEI-Int-RHC-01.1270

Uponor Radiant Heating/Cooling > Uponor industrial underfloor heating


Uponor Industrial Underfl oor Heating

Uponor industrial underfl oor heating is a low-temperature heat distribution system for heating industrial spaces. The system is built directly into the concrete fl oor slab. It is even possible to make use of the standard steel reinforcement

for the concrete slab as a support structure for the heating pipes. Heat can be supplied by any conventional warm water heating system designed for use in the type of building being in question.

Your advantages Rapid return on investment Total design space freedom Optimal building space utilisation Uniform temperature profi le Low air speeds No dust circulation Stimulating working environment No maintenance costs Proven technology Extensive declaration of liability

System components

Uponor industrial clamp track

Systempipe / -Fittings Additional components Manifold / Cabinets

Uponor industrialmanifold 25-G 11/2

Uponor cable tie Uponor Q&E PPSU coupling

Uponor pipe clips Uponor Q&E brass connection with male thread

Uponor PE-Xa pipe 25x2.3 or 20x2.0

150

/2

D

Uponor tying wire

Uponor pipe bend suport

Uponor conduit


Uponor industrial fl oor heating PE-Xa pipes







1023448 25 2.3 205 6 Uponor eval PE-Xa Q&E pipe 25x2.3coil lengths 205 m 205 m



Uponor PE-Xa Q&E fi ttings

Uponor Q&E PPSU coupling equalMade of PPSU. Note: Uponor Q&E Ring must be ordered separately!

Item no. d [mm] p [bar] Description unit

1008932 20 6+10 Uponor Q&E PPSU coupling 20-20 5 pcs


l

d

SWSW1

z

IG

l

d

SWSW1

z

AG

Uponor compression adapterCompression adapter made of brass, for connection of Uponor PE-X pipes with 3/4" female thread.

Item no. d [mm] MT ["] FT ["] l [mm] A/F [mm] z [mm] Description unit

1005295 25 R 3/4 50 37/27 15 Uponor compression adapter 25x2.3-3/4"MT 10 pcs

1005296 25 Rp 1 40 37/38 8 Uponor compression adapter 25x2.3-1" FT 10 pcs

1005297 25 Rp 3/4 35 37/31 8 Uponor compression adapter 25x2.3-3/4 FT 10 pcs

1005298 25 R 1 53 37/34 20 Uponor compression adapter 25x2.3-1" MT 10 pcs

EEI-Int-RHC-01.1272


Uponor PE-Xa Q&E fi ttings

Uponor Q&E brass connection with male threadMade of DR brass. Male thread acc.to DIN EN 10226-1 for sealing in. Note: Uponor Q&E Ring must be ordered separately!

Item no. d [mm] MT ["] p [bar] Description unit

1023006 20 R 3/4 6+10 Uponor Q&E connection with male threadtaper, 20-3/4 5 pcs


1023008 25 R1 6+10 Uponor Q&E connection with male threadtaper, 25-1 5 pcs

Uponor Q&E brass connection with female threadMade of DR brass. Female thread acc. to DIN EN 10226-1. Note: Uponor Q&E Ring must be ordered separately!

Item no. d [mm] FT ["] p [bar] Description unit

1023011 20 Rp 3/4 6+10 Uponor Q&E connection with female thread20-3/4 5 pcs


1023013 25 Rp 1 6+10 Uponor Q&E connection with female thread25-1 5 pcs

Uponor Q&E ring naturalMade of PE-X. Uponor Q&E rings natural intended for Uponor Q&Efittings. For PE-Xa pipe dimensions 16, 20, 25, 32, 40, 50 and 63 mm.

Item no. d [mm] colour [-] p [bar] Description unit

1042836 20 natural 6+10 Uponor Q&E ring natural with stop edgeUponor PE-Xa dim 20 mm 20 pcs

1042840 25 natural 6+10 Uponor Q&E ring natural with stop edgefor Uponor PE-Xa dim 25 mm 20 pcs

Uponor industrial fl oor heating fi xation and accessories

ra

d

h

l b

Uponor industrial clamp trackUponor clamp track for fixation of Uponor PEX pipes.

Item no. w [mm] h [mm] d [mm] c/c [mm] l [mm] Description unit

1005290 50 34 25 50 3000 Uponor clamp track for 25 mm pipes 30 m


Uponor fastening nailFor fastening the Uponor clamp track 25

Item no. w [mm] h [mm] Description unit

1005291 36 50 Uponor fastening nail forindustrial floor heating clamp track 500 pcs



Uponor industrial fl oor heating fi xation and accessories

Uponor pipe clipsFor fastening Uponor pipes on reinforcement steel meshes.

Item no. h [mm] h1 [mm] w [mm] d [mm] d1 [mm] Description unit

1005289 57 27 38 25 3-8 Uponor pipe clipsfor PE-Xa pipe 25x2.3 250 pcs










1009233 20 Uponor pipe bend support20 mm 50 pcs


Uponor conduitCorrugated, fire classification E conforming to DIN EN 13501-1. Supplied in coils.

Item no. d [mm] d1 [mm] d2 [mm] colour [-] Description unit

1012869 35/29 25 black Uponor conduit black 35/29 MLC 25 50 m

EEI-Int-RHC-01.1274


Uponor industrial fl oor heating manifold and accessories

Uponor industrial manifold 25-G 11/2Uponor Industrial Manifold 25-G 11/2 as supply / return for Industrialheating, made of:- supply-segment, with control valves for preadjustment, heating loop connection for PE-Xa Pipe 25x2,3 with compression adapter.- return-segment with thermostat upper section incl. cap for locking, Uponor actuator can be mounted directly on the return manifold , heating loop connection for PE-Xa Pipe 25x2,3 with compression adapter

Spacing of outlet: 100 mmMaterial: fibreglass reinforced Polyamidmax. operating temperatur: 60 °Cmax. operating pressure 6 bar

induvidual combination up to 20 loops max.

Number of needed brackets

loops 2-5 6-9 10-14 15-19 20bracket 2 3 4 5 6


1045813 Uponor industrial manifold 25-G 1 1/2" 1 set

Uponor industrial manifold G3/4 Eurconeas supply / return for Industrialheating, made of:- supply-segment, with control valves for preadjustment, heating loop connection for G3/4 eurocone.- return-segment with thermostat upper section incl. cap for locking, Uponor actuator can be mouinted directly on the return manifold , heating loop connection for G3/4 eurocone.

Spacing of outlet: 100 mmMaterial: fibreglass reinforced Polyamidmax. operating temperatur: 60 °Cmax. operating pressure: 6 barinduvidual combination up to 20 loops max.

Quantity necesary bracketloops 2-5 6-9 10-14 15-19 20bracket 2 3 4 5 6


1045814 Uponor industrial manifold G3/4 eurocone 1 set

Uponor industrial manifold basic kitUponor Industrial Manifold Basic Kitfor mounting the industrial manifold, made of:- 2 St. brackets short- 2 St. brackets long- 2 St. filling valve brass- 2 St. thermometer 0 - 60°C- 1 St. manometer- 2 St. endcap- 2 St. flat sealing screw connection piece with swivel nut- 1 St. mounting material: 8x screws 6x60mm 8x plastic anchor 8x40mm 2x flat sealing 44x32x2


1045815 Uponor industrial manifold basic kit 1 set



Uponor industrial fl oor heating manifold and accessories

Uponor industrial manifold bracket kitUponor Industrial Manifold Bracket Kitfor mounting the Industrial manifold, made of:- 2 St. brackets short- 2 St. brackets long- 1 St. mounting material: 8x screws 6x60mm 8x plastic anchor 8x40mm


1045816 Uponor industrial manifold bracket kit 1 set

Uponor industrial flowmeterUponor Industrial FlowmeterFor adjusting the water quantity of the individual heating loops in a rangeof 4 -20 l/min. Water quantity is indicated in the inspection window. Withshut-off function. Made of fibre-glass reinforced polyamid.

Material: fibreglass reinforced Polyamid


1030134 Uponor industial flowmeter 1 pcs

Uponor industrial ball valve G 11/2Uponor Industrial Ball Valve G 11/2for use with the Uponor Industrial manifold G 11/2connection:- G 11/2 FT- G 11/2 MTMaterial: brass


1030135 Uponor industrial ball valve G 1 1/2" 1 set

EEI-Int-RHC-01.1276

Uponor Radiant Heating/Cooling > Uponor snow and ice melting


Uponor snow and ice melting

Uponor snow and ice melting system is best suitable for all outside surfaces which are provided with a solid covering. It will be especially used for driveways, ramps, fi re department or hospital approach roads, helicopter

landing zones, sidewalks, football pitches, etc..

Your advantages System ensures a maximum of security - round the clock Automatically deicing, no more shoveling of snow Avoids environmental stress and damage through de-icing

salt Usage of industrial waste heat possible Fast and easy installation with robust Uponor PE-X pipes Complete system with all components available Reduces slip and fall liability

System components Systempipe / -Fittings Additional components Manifold / Cabinets

Uponor compression adapterPE-X

Uponor industrial clamp track

Uponor Manifolds

Uponor fastening nail

Uponor Supply pipes

Uponor tying wire

Uponor supply accessories

Uponor electrofusion fi tting

Uponor snow and ice melting pipe 25x2.3

D

Uponor cable tie Uponor pipe bend suport

Uponor conduit


Uponor snow and ice melting pipes

Uponor snow and ice melting pipeUponor snow and ice melting pipes manufactured from cross-linked polyethylene, complying with e.g. EN ISO 15875 ”Plastics piping systems for hot and cold water installations - Cross-linked polyethylene”. Application for underfloor heating up to 50 °C water temperature Design pressure 4 bar.


1022341 Uponor Meltaway PE-X pipe 25x2.3920 m 920 m

1033625 Uponor Meltaway PE-X pipe 25x2.31020 m 1020 m

1033626 Uponor Meltaway PE-X pipe 25x2.3other lengths <1000m 1 m

Uponor snow and ice melting manifold and accessories

Uponor manifoldsUponor snow and ice melting single manifold made of high density polyethylene (HDPE) pipe and equipped with compact-welded couplings. Couplings between centres are 500mm.


1033637 Uponor Meltaway manifold 10 waysingle outlet, C/C 600 75 6m 1 pcs









Uponor manifoldsUponor snow and ice melting single manifold made of high density polyethylene (HDPE) pipe and equipped with compact-welded couplings. Couplings between centres are 500mm.





EEI-Int-RHC-01.1278



Uponor manifoldsUponor snow and ice melting double manifold made of high density polyethylene (HDPE) pipe and equipped with compact-welded couplings oriented in two directions with an angle of 120° between them.


1033634 Uponor Meltaway manifold 12 waydouble outlet, C/C 500 75 6m 1 pcs





Uponor couplingUponor straight couplings for snow and ice melting PE-X pipes 25x2.3 Made of HDPE.


1033672 Uponor Meltaway coupling 25x2.3 mmshort, 145 mm 1 pcs

1033678 Uponor Meltaway coupling 25x2.3 mmlong, 290 mm 1 pcs

Uponor supply pipesUponor snow and ice melting supply pipes made of HDPE.


1033628 Uponor HDPE supply pipe 75x6.8 mmL=6000 mm 1 m



Uponor supply pipes teesUponor snow and ice melting tees made of HDPE.


1033648 Uponor tee 75 1 pcs






Uponor supply pipes elbowsUponor snow and ice melting elbows made of HDPE.


1033652 Uponor elbow 75 x 90° 1 pcs



Uponor supply pipes reducerUponor snow and ice melting reducer made of HDPE.


1056656 Uponor reducer 110-75 1 pcs

1033657 Uponor reducer 160 - 110 1 pcs

Uponor supply pipes end capUponor snow and ice melting end cap made of HDPE.


1033659 Uponor end cap 75 1 pcs



Uponor flange supportUponor snow and ice melting flange support for connection of Uponor flange to supply/return pipes. Made of HDPE.


1033662 Uponor flange support 75 1 pcs



EEI-Int-RHC-01.1280



Uponor flangeUponor snow and ice melting flange made of HDPE.


1033666 Uponor flange 75x6.8 mm 1 pcs



Uponor electrofusion fittingUponor snow and ice melting electrofusion fittings made of HDPE.


1033673 Uponor electrofusion fittingfor pipe 75x6.8 mm 1 pcs



ra

d

h

l b

Uponor industrial clamp trackUponor clamp track for fixation of Uponor PEX pipes.

Item no. w [mm] h [mm] d [mm] c/c [mm] l [mm] Description unit


Uponor fastening nailFor fastening the Uponor clamp track 25

Item no. w [mm] h [mm] Description unit

1005291 36 50 Uponor fastening nail forindustrial floor heating clamp track 500 pcs

















l

d

SWSW1

z

IG

l

d

SWSW1

z

AG

Uponor compression adapterCompression adapter made of brass, for connection of Uponor PE-X pipes with 3/4" female thread.

Item no. d [mm] MT ["] FT ["] l [mm] A/F [mm] z [mm] Description unit

1005297 25 Rp 3/4 35 37/31 8 Uponor compression adapter 25x2.3-3/4 FT 10 pcs

1005296 25 Rp 1 40 37/38 8 Uponor compression adapter 25x2.3-1" FT 10 pcs

1005295 25 R 3/4 50 37/27 15 Uponor compression adapter 25x2.3-3/4"MT 10 pcs

1005298 25 R 1 53 37/34 20 Uponor compression adapter 25x2.3-1" MT 10 pcs

Uponor chamfering toolFor de-studding the Uponor snow and ice melting pipe.


1033689 Uponor Meltaway chamfering toolfor Uponor Meltaway 25 mm pipe 1 pcs

EEI-Int-RHC-01.1282

Uponor Radiant Heating/Cooling > Uponor sport floor heating


Uponor sports fl oor heating

Uponor radiant heating system for surface elastic fl oors. These fl oors are a synthesis of woo-den swing fl oors with elastic layer made of PVC or linoleum. The heating registers runs in pipe holders (Patent Uponor) directly under the blind fl oor.

The pipes are to be connected to distribute- /collector pipes.

Uponor sports fl oor heating systems are quick installed. First due to the fl exible and at the same time robust PE-Xa pipe material. Secondly due to the patented mounting principle for swing fl oor constructions.

Your advantages Sports fl oor heating systems off er high thermal comfort Provides mild radiant heat and an even temperature

distribution with low air speed Gives athletes and architectures all freedom, because the

system is invisible Takes all hygienic and physiologic requirements of sports

halls into consideration Energy saving due to operation with low heating water

temperatures

System components

Uponor pipe fi xation

Systempipe / -Fittings

Uponor eval PE-Xa pipe in coils

Additional components Manifold / Cabinets

Uponor Q&E tichelmann manifold for sportsfl oor UFH

Uponor pipe fi xation double

sprung fl oors

Uponor pipe bend suport

Uponor conduit


Uponor sport fl oor PE-Xa pipes






Uponor sport fl oor PE-Xa Q&E fi ttings




Uponor Q&E brass connection with male threadMade of DR brass. Male thread acc.to DIN EN 10226-1 for sealing in. Note: Uponor Q&E Ring must be ordered separately!

Item no. d [mm] MT ["] p [bar] Description unit


1023008 25 R1 6+10 Uponor Q&E connection with male threadtaper, 25-1 5 pcs




1023013 25 Rp 1 6+10 Uponor Q&E connection with female thread25-1 5 pcs



1042840 25 natural 6+10 Uponor Q&E ring natural with stop edgefor Uponor PE-Xa dim 25 mm 20 pcs

EEI-Int-RHC-01.1284


Uponor sport fl oor fi xation and accessories

Uponor pipe fixationFor exact leading of pipes inside the channels of sport floor Material: Polyamid

Item no. l [mm] sd [mm] c/c [mm] l1 [mm] h [mm] Description unit

1005286 290 45 100 145 50 Uponor pipe clip trackfor floors in gyms. Polyamid 25 pcs

Uponor pipe fixation doubleFor exact leading of pipes in the bending zone of chanels of sport floorMaterial: galvanised steel

Item no. l1 [mm] c/c [mm] l [mm] Description unit

1005284 105 100 975 Uponor double pipe clip track for floorsin gyms. galvanised steel 1 pcs

Q&E tichelmann manifold 2 circuits for sportsfloor UFHas manifold for the use in sportsfl oor UFH systems according to theTichelmann principle. For connection of Uponor PE-Xa pipes 25x2.3mmwith Uponor Q&E connection technology consisting of:- 1 manifold (distributor & collector)- 4 Q&E rings 25- 2 Q&E rings 40Material: Uponor eval PE-Xa pipes + Uponor PPSU fittings.

Item no. d [mm] l [mm] c/c [mm] Description unit

1046747 40 2084 150 Uponor Q&E tichelmann manifold2 circuits for sportsfloor UFH 1 set

Q&E tichelmann manifold for sportsfloor UFHas manifold for the use in sportsfloor UFH systems according to theTichelmann principle. For connection of Uponor PE-Xa pipes 25x2.3mmwith Uponor Q&E connection technology consisting of:- 1 manifold (distributor & collector)- 6 Q&E rings 25- 2 Q&E rings 40

Material: Uponor eval PE-Xa pipes + Uponor PPSU fittings


1046748 40 2084 150 Q&E tichelmann manifold for sportsfloor UFH 1 set

Q&E tichelmann manifold end segment for sportsfloor UFHas manifold for the use in sportsfloor UFH systems according to theTichelmann principle. For connection of Uponor PE-Xa pipes 25x2.3mmwith Uponor Q&E connection technology consisting of:- 1 manifold (distributor & collector)- 6 Q&E rings 25

Material: Uponor eval PE-Xa pipes + Uponor PPSU fittings


1046749 40 2036 150 Q&E tichelmann manifold end segmentfor sportsfloor UFH 1 set




Uponor eval PE-Xa pipes in straight lengthsPipes manufactured from peroxide cross-linked polyethylene (PE-Xa) using the Engel method, complying with e.g. EN ISO 15875 ”Plastics piping systems for hot and cold water installations - Cross-linked polyethylene”. Includes an ethylene vinyl alcohol (EVOH) oxygen barrier layer, complying with DIN 4726, to prevent corrosion of system components. This barrier has been specially developed to work together with Q&E fitting technology. Classification of service conditions (including typical field of application): Application class 4 - Underfloor heating and low temperature radiators, malfunction temperature 95 °C. Design pressure 6 bar. Application class 5 - High temperature radiators, malfunction temperature 95 °C. Design pressure 6 bar.


1008939 40 3.7 6 6 Uponor eval PE-Xa Q&E pipe40x3.7 mm in straight lengths of 6 m 6 m



1008673 40 6 Uponor Q&E PPSU coupling 40-40 1 pcs

Uponor Q&E PPSU elbow 90°Made of PPSU. Note: Uponor Q&E Ring must be ordered separately!


1008683 40 6 Uponor Q&E PPSU elbow 90° 40-40 1 pcs



1045464 40 natural 6 Uponor Q&E ring natural with stop edgefor Uponor PE-Xa dim 40 mm 5 pcs



1047867 40 Rp 1 1/4 6 Uponor Q&E connection with female thread40-1 1/4 1 pcs

EEI-Int-RHC-01.1286










Uponor Radiant Heating/Cooling > Uponor comfort panel

EEI-Int-RHC-01.1288

Uponor Comfort Panel

Your advantages cooling power up to 92.5 W/m² with 10K under

temperature Heating power up to 82.5 W/m² with 15 K under

temperature Compatible with existing metal rail constructions easy to install quick installation concealed installation/integrated in the ceiling structure easily retrofi tted into existing ceiling structure excellent for both new buildings and refurbishment easy to operate maintenance-free.

System components

Uponor Comfort Panel


Uponor PE-X Pipe 10x1.5


Uponor Dynamic volume fl ow controller

Manifold / Cabinets

Uponor Slip ConnectorUponor blind panel

Uponor connection MLC

Uponor connection with female threat

The Uponor comfort panel is a suspended ceiling system which can be used for heating and cooling. The system consist of thermally activated ceiling panels which can be installed fast and easy into conventional suspended ceiling grids.


Uponor comfort panel

b

l h

Uponor comfort panelFor cooling and heating of buildings with suspended raster frame ceiling. For already existing or new raster frames under the ceiling. With optically sophisticated surface from fleece coated steel sheet. High performance due to optimised thermal conductivity between surface and integrated pipes, made of PE-X, with thermal insulation made of mineral fibres.Cooling capacity 74 W/m² by 8 K temperature difference complies withEN 14240Heating capacity 103 W/m² by 15 K temperature difference complies with EN 14037


1045315 1240 615 23 Uponor comfort panel 1250 x 625 1 pcs


b

l h

Uponor comfort panelFor cooling and heating of buildings with suspended raster frame ceiling. For already existing or new raster frames under the ceiling. With optically sophisticated surface from fleece coated steel sheet. High performance due to optimised thermal conductivity between surface and integrated pipes, made of PE-X, with thermal insulation made of mineral fibres.Cooling capacity 74 W/m² by 8 K temperature difference complies with EN 14240Heating capacity 103 W/m² by 15 K temperature difference complies with EN 14037






Uponor comfort panel - accessories

b

l h

Uponor blind panelFor use in on-site installed suspended raster ceilings. With optically sophisticated surface from fleece coated mineral faser board, optically fits exactly to comfort panel.Colour from below: whiteAcoustical absorption (alpha w): 1,00Acoustical absorption (NRC): 0,95Building material class according to DIN 4102: A1

Item no. l [mm] w [mm] h [mm] A [m²] Weight [kg] Description unit

1022983 1242 617 18 0.76 2.08 Uponor Blind Panel 625dimension 617 x 1242 x 18 16 pcs

1022984 1195 595 18 0.71 1.93 Uponor Blind Panel 600dimension 595 x 1195 x 18 16 pcs

b

l h

Uponor blind panelFor use in on-site installed suspended raster ceilings. With optically sophisticated surface from fleece coated mineral faser board, optically fits exactly to comfort panel.Colour from below: whiteAcoustical absorption (alpha w): 1,00Acoustical absorption (NRC): 0,95Building material class according to DIN 4102: A1


1045319 615 615 18 Uponor Blind Panel 625 x 625 32 pcs

1045320 590 590 20 Uponor Blind Panel 600 x 600 32 pcs

l

b Uponor blind frameFor use in existing suspended ceiling constructions for optical devision into a quadratic raster.

Item no. l [mm] w [mm] colour [-] Description unit

1045323 625 24 white Uponor blind frame 625, white 1 pcs

1045324 600 24 white Uponor blind frame 600, white 1 pcs

EEI-Int-RHC-01.1290



Uponor PE-X pipe 10 x 1,5 mmAs pipe in coils for connection or extension between 2 comfort panels.Material: Uponor PEX pipe from high pressure cross-linked polyethylene

Medium: heating/cooling water acc. to VDI 2035 or water-glycol up to 50%Temperature range: 0 to 60°CPressure range: 0 to 6 bar by max. 65 °C0 to 12 bar by max. 20 °CSurrounding humidity: up to 90%Material: plastic


1045327 10 1.5 100 Uponor PE-X pipe 10 x 1,5 mm, in coilsbarrier, 10x1,5 coil 100m, 6bar 100 m

b

d

Uponor pipe insert, for 10x1,5 PE-X pipePipe sleeve made of plastic, for plug in PE-X pipe ends, dimension 10 x 1,5 mm, for stiffening of a pipe in connection area with Uponor slip-connector.

Item no. w [mm] d [mm] Description unit

1045328 5 7 Uponor support sleeve, 10 x 1,5 mm 10 pcs

l

d

Uponor slip-connectorPush-in fitting for connection of more comfort panels together into one control circuit or to one ceiling panel area.Medium: heating/cooling water acc. to VDI 2035 or water-glycol up to 50%Temperature range: 0 to 60 °CPressure range: 0 to 6 bar by max. 65 °CSurrounding humidity: up to 90%Material: plastic

Item no. l [mm] d [mm] Description unit

1045325 45 22 Uponor slip-connector equal 10 mm 100 pcs

1022987 60 15 Uponor slip connector equal 15 mm 10 pcs

l

d3 d2d1

Uponor slip-connector reduced 15-10 mmPush-in fitting for connection of more comfort panels together into one control circuit or to one ceiling panel area.Medium: heating/cooling water acc. to VDI 2035 or water-glycol up to 50%Temperature range: 0 to 60 °CPressure range: 0 to 6 bar by max. 65 °CSurrounding humidity: up to 90%Material: plastic

Item no. l [mm] d1 [mm] d2 [mm] d3 [mm] Description unit

1045326 56 32 10 15 Uponor slip-connector reduced 15-10 mm 100 pcs

l

d

Uponor Stop plug 15as end plug 15 mm, for closing of capillary mats endsMaterial: nickel-plated brass

Item no. d [mm] l [mm] Description unit

1000296 15 35 Uponor stop plug 15 10 pcs




63,9

ø 51

,4

Uponor Diversion Fitting Dim Cu 22 – 4x Dim 10 push-in (CPII Manifold)Uponor Diversion Fitting Dim Cu 22 – 4x Dim 10 push-in allows the connection of four series of panels to a MLC 20 mm pipe using an Uponor Press Adapter MLC 20-22CU (item number 1014558). Temperature range: 0 – 60°CPressure range: 0-6 bar Material: plastic


1048684 Uponor Diversion Fitting Dim. Cu 224x Dim 10 push-in 1 pcs

35

18

ø 10

ø 10

± 0

,1

Uponor Endplug Dim 10 push-inUponor Endplug Dim 10 push-in to close an open distribution line from the Uponor diversion fitting Cu 22 – 4x 10 mm push-in (1048684)Temperature range: 1 – 60°CPressure range: 0-6 bar Material: plastic


1048685 Uponor Endplug Dim 10 push-in 1 pcs

l

d d1

Uponor connection MLCFor connection of 15 mm push-in system to Uponor MLC pipe.Material: nickel-plated brass, press sleeve

Item no. d [mm] d1 [mm] l [mm] Description unit

1000297 15 16x2.0 70 Uponor connectionto MLCP 15-16x2 6 pcs

1000298 15 20x2.25 70 Uponor connectionto MLCP 15-20x2.25 6 pcs

d

l

AG

Uponor connection with male threatfor connection of 15 mm push-in system to male threat.Material: nickel-plated brass

Item no. d [mm] MT ["] l [mm] Description unit

1000299 15 R 1/2 57 Uponor connectionwith male threat 15-1/2 MT 6 pcs

1000300 15 R 3/4 57 Uponor connectionwith male threat 15-3/4 MT 6 pcs

AG

l

d

Uponor push-in compression adapterfor connection of 15 mm push-in system to female threat.Material: nickel-plated brass

Item no. d [mm] MT ["] l [mm] Description unit

1000301 15 R 1/2 41 Uponor push-in compressionadapter15-1/2 FT 6 pcs

d

l

l1

d1

Uponor connection elbowfor connection of 15 mm push-in system to Uponor MLC pipe, in 90° version.Material: nickel-plated brass, press sleeve

Item no. d [mm] d1 [mm] l [mm] l1 [mm] Description unit

1000303 15 16x2 45 48 Uponor connection elbow to UponorMLC pipes, 15-16x2 6 pcs

1000304 15 20x2.25 45 48 Uponor connection elbow to UponorMLC pipes, 15-20x2,25 6 pcs

EEI-Int-RHC-01.1292



Uponor locking ring 15for capillary pipe 15 mm push-in fitting. Ensures the coupling against unintended (unbeabsichtigtes) solutions of push-in connection.Material: polypropylene


1000310 15 Uponor locking ring 15 10 pcs

Uponor ball valveFor closing of cooling and heating areas and supply pipes.Medium: heating/cooling water acc. to VDI 2035 or water-glycol up to 50%Temperature range: -10 to + 110 °CPressure range: 0 to 10 barSurrounding humidity: up to 95%Material: nickel-plated brass

Item no. l [mm] FT ["] Description unit

1022985 50 G 1 Uponor ball valvedimension 1 FT - 1 FT 1 pcs

1022986 50 G 3/4 Uponor ball valvedimension 3/4 FT - 3/4 FT 1 pcs

Uponor reductionReducer from 3/4 MT to 1/2 FT by use of tees for supply and return MLC pipes from dimension 40 x 4 mmMaterial: brass

Item no. FT ["] MT ["] Description unit

1022988 Rp 1/2 G 3/4 Uponor reductiondimension 1/2 FT - 3/4 MT 10 pcs

Dynamic volume flow controllerFor hydraulic control of heating and cooling loops, or zones and indvidual control over integrated valve insert in combination with thermla actuator.

Item no. DN [mm] Description unit

1042942 15 Dynamic volume flow controllerAB-QM DN 15, flow rate 55 - 275 L/H 1 pcs

1042943 20 Dynamic volume flow controllerAB-QM DN 20, flow rate 180 - 900 L/H 1 pcs

1042944 25 Dynamic volume flow controllerAB-QM DN 25, flow rate 340 - 1700L/H 1 pcs

1042945 32 Dynamic volume flow controllerAB-QM DN 32, flow rate 640 - 3200L/H 1 pcs

Screw connection for AB-QMScrew connection Inclusively flat sealing

Item no. Type [-] Description unit

1044809 15 Screw connection for AB-QM 3/4 MT 1 pcs

1044810 20 Screw connection for AB-QM 1 MT 1 pcs

1044811 25 Screw connection for AB-QM 1 1/4 MT 1 pcs

1044812 32 Screw connection for AB-QM 1 1/2 MT 1 pcs


[l/h] stroke [mm] [-]

90-450 2.25 G 3/4" A

180-900 2.25 G 1" A

340-1700 2.25 G 1 1/4" A

640-3200 2.25 G 1 1/2" A

FT ["] MT ["]

Rp 3/4" R 1/2"

Rp 1" R 3/4"

Rp 1 1/4" R 1"

Rp 1 1/2" R 1 1/4"



Thermal actuator TWA -Z NOFor control of pressure indipendent volume flow controller - openes when idle.

Item no. Type [-] [-] Description unit

1042946 TWA-Z NO Thermal actuator TWA -Z NO 1 pcs

Thermal actuator TWA -Z NCFor control of pressure indipendent volume flow controller - closes when idle.

Item no. Type [-] [-] Description unit

1042947 TWA-Z NC Thermal actuator TWA -Z NC 1 pcs

l

l1

h

Uponor room temperature controller H/CConcealed device, protects cooling surface from condensation. The TR 2/3 (concealed device) can both to control one valve (heating or cooling) and also be switched over internally to control thus 2 valves (heating and cooling). With an option of external setpoint remove access will it be introduced in two-line (heating and cooling) and three-line systems (heating and cooling). The actual operation status (heating/cooling/dew point warning) will be show on device by means of light diods. For simplification of wiring and installation of room temperature are switch boxes shall be provided.Operational voltage: 24 V / 50-60 HzControl range: 5-30 °CSwitching hysteresis: 1 KTemperature sensor: NTCSwitch outlet: Triac, 24 V/1 A, short-term up to 2,5 AFunctions:Heating or coolingHeating or cooling with switchoverHeating and/or cooling with setpoint remot accessInstallation site: concealed under plaster, fits into UP-Doses acc. to DIN 49073Installation depth: 28 mmColour: RAL 9010, pure white

Item no. l [mm] l1 [mm] h [mm] Description unit

1000311 71 70 28 Uponor room thermostatTR 2/3 1 pcs

EEI-Int-RHC-01.1294



Uponor dew point sensorFor plastered ceilings or walls / pipe installation, detects a potential condensation arising on the pipe or in the immediate vicinity by changing its electrical resistance. This change of resistance in the sensor is detected by room thermostat TR 2/3, which closes control valve and effectively protects the cooling surface from condense damage. The dew point sensor TF 3 PR is designed for installation in plastered ceilings (P) and for cold-water pipe conduits (R).Installation site: plastered ceilings/walls or pipe installations


1000312 70 20 7 Uponor dew point sensorTF 3 PR 1 pcs

Uponor dew point sensorFor gypsum plasterboard ceilings / suspended metal ceilings, detects a potential condensation arising on the pipe or in the immediate vicinity by changing its electrical resistance. This change of resistance in the sensor is detected by room thermostat TR2/3, which closes control valve and effectively protects the cooling surface from condense damage.The dew point sensor TF 3 GM is designed for installation in gypsum plasterboard ceilings/walls (G) and for suspended metal ceilings (M).Installation site: gypsum plasterboard ceilings/walls or suspended metal ceiling


1000313 70 20 7 Uponor dew point sensorTF 3 GM 1 pcs

l

b h Uponor dew point converterEvaluates the information received from the corresponding dew point sensor. The integrated contact is activated when the dew point is reached. This information can be used, for example, for remote communications with an onsite central building control system or similar device. Up to five dew point sensors can be assigned to each converter.Operating voltage: 24 V / 50-60 HzSwitch outlet: potential free switch over contact max. load capacity of the outlet: 48 V~/60 V DCInstallation site: automation cabinet or electric manifold installation


1000314 85 36 60 Uponor dew-point converterTK 1 PF 1 pcs


Uponor Radiant Heating/Cooling > Uponor gypsum panel

EEI-Int-RHC-01.1296

Uponor Gypsum Panel is the ideal system for heating and cooling. The moderate temper-ature of the water feeds the radiant system makes it partic-ularly suitable to be combined with condensing boilers, heat pumps, solar panels and other

alternative sources of energy.

Your advantages quick and easy to install for new buildings and renovation high comfort fast response time completely silent (no fan noise).

System components

Uponor Gypsum Panel


Uponor PE-Xa pipe 9,9 x 1,1


Uponor PE-Xa pipe20x2

Manifold / Cabinets

Uponor compression Adapter

Uponor PE-Xa Q&E Coupling

Uponor PE-Xa Q&E teereducer 20x9.9x20

Uponor PE-Xa Pipe 9.9x1.1 expander

Uponor PE-Xa Q&E jointing reducer 20x9.9

Uponor Gypsum Panel

Uponor Gypsum panel passive

velta P�-�a


Uponor gypsum panel

Uponor gypsum panelRadiant panel for heating and cooling applications. Consisting of a gypsum board (15mm), Uponor eval PE-Xa pipe 9.9x1.1 mm and 27mm of EPS 200 (30 kg/m³). Uponor gypsum passive panel has the same layout as the active panels but consists no pipes.

Sizes: 2000x1200mm, 1000x1200mm, 500x1200mm.


1047319 42 2000 1200 2.40 Uponor gypsum panel 2000x1200 Type 2 1 pcs



Uponor gypsum panel passiveUponor gypsum panel passive has the same layout as the active gypsum panels (item no. 1047319-21) but contains no pipes.

Size: 2000x1200mm


1020506 42 2000 1200 2.40 Uponor gypsum panel passive 2000x1200 1 pcs

Uponor gypsum panel - accessories













Uponor gypsum panel - accessories

Uponor PE-Xa Q&E jointing reducer 20x9.9For connection of Uponor PE-Xa pipes, made of brass.

Item no. d [mm] d1 [mm] Description unit

1020518 9.9 20 Uponor PE-Xa Q&E jointing reducer 20 x 9.9incl. 1 PEX ring 9.9 and 1 PEX ring 20 5 pcs

Uponor PE-Xa Q&E tee reducer 20x9.9x20For connection of Uponor PE-Xa pipes, made of brass.

Item no. d [mm] d1 [mm] d2 [mm] Description unit

1020524 20 9.9 20 Uponor PE-Xa Q&E tee reducer 20 X 9.9 X 9.9incl. 1 PEX ring 9.9 and 2 PEX rings 20 5 pcs



1042836 20 natural 6+10 Uponor Q&E ring natural with stop edgeUponor PE-Xa dim 20 mm 20 pcs




EEI-Int-RHC-01.1298

Uponor Radiant Heating/Cooling > Uponor tools

Uponor tools

Uponor pipe cutter up to 25 mmFor Uponor pipes, outside diameter up to 25 mm.


1001369 - 25 Uponor pipe cutter for PEX14-25mm 1 pcs

Uponor pipe cutter up to 20For Uponor pipes, outside diameter up to 20 mm with corrugated pipe cutting device.


1006636 - 20 Uponor pipe cutter 14-20 mm 1 pcs

1006637 Uponor spare bladefor pipe cutter 1006636 1 pcs

Uponor cutting aidFor the easy cutting of Uponor pipe fixing system panels.


1016724 Uponor cutting tool for pipe positioning panel 14-16mmwith insulation 1 pcs

Uponor polystyrene cutter tool for lightweight systemFor cutting of individual pipe curves and guides. And also for the smooth cutting to size of polystyrene items. 230 V connection.

Item no. OV [V] Description unit

1006290 230 Uponor polystyrene cutting toolfor lightweight system 1 pcs

Uponor outside bending spring MLCSpecial bending spring for Uponor MLC pipe.


1006639 14 Uponor bending spring outside MLC 14 1 pcs

1006640 16 Uponor bending spring outside MLC 16 1 pcs



Uponor tools

Uponor manual pressing tool MLCFor pressing of Uponor press fittings MLC 14-20 mm in conjunction with exchangeable inserts. Supplied in case without exchangeable inserts.


1015764 14-20 Uponor manual press tool MLC 14-20incl. case without pressing inserts 1 pcs

Uponor manual pressing tool inserts MLCFor inserting into the manual pressing tool for pressing the Uponor press fittings MLCP 14/16/18/20 mm.


1015776 14 Uponor manual press tool insert MLC 14 1 set



Uponor press tool electric UP 75Supplied in plastic case for the 230 V mains connection, without pressingjaws. Range of application up to 110 mm.Technical Specifications:Weight of the pressing tool: 3.30 kgNominal voltage: 230 V DC / 50 HzNominal capacity: 200 WattFor dimensions: up to 110 mmPress power: ca. 32 kNPress duration: ca. 7 sec.

Item no. d [mm] OV [V] Description unit

1007082 - 110 230 Uponor electric pressing tool UP 75 ELwithout pressing jaws 1 pcs

Uponor PE-Xa pipe 9.9x1.1 expanderHand tool for the easy expansion of Uponor PE-Xa pipes 9.9 x 1.1 mm, consisting of:- 1 hand expander- 1 expander head for PE-Xa pipe 9.9 x 1.1 mm- 1 tube of lubricant- 1 case


1006247 Uponor PE-Xa pipe 9.9 x 1.1 expandertool 1 set

EEI-Int-RHC-01.12100


Uponor tools

Uponor Q&E battery tool M12Battery powered expander tool for 6 bar pipes up to dimension 32mm and for 10 bar pipes up to 28 mm. Auto-rotating with M12 expander heads.< 10seconds full expansion onto a joint< 2.2kg with head and batterySteel gear and integrated metal frameLED work light, fuel gauge, Tool free head change incl. 2 Li-ion 1.5 Ah batteries, charger 220-240V/50-60Hz and grease (Mo)


1057166 Uponor Q&E M12 expanderwith 6 bar heads 16-20-25 1 set

Uponor Q&E battery tool M18Battery powered expander tool for 6 bar pipes up to dimension 40mm and for 10 bar pipes up to 32 mm. Auto-rotating with M18 expander heads.< 10seconds full expansion onto a joint.< 2.2kg with head and batterySteel gear and integrated metal frameLED work light, fuel gauge, Tool free head change incl. 2 Li-ion 1.5 Ah batteries, charger 220-240V/50-60Hz and grease (Mo)


1057169 Uponor Q&E M18 expanderwith 6 bar heads H20-H25-H32 1 set

Uponor Q&E M12 expander headsQ&E head for NKB fittings, for M12 and M18 tools.Expander head packed screw pack

Item no. d [mm] stroke [mm] p [bar] Description unit

1057184 15 14 10 Uponor Q&E M12 expander head14/15x2.5 mm 1 pcs

1057185 18 14 10 Uponor Q&E M12 expander head17/18x2.5 mm 1 pcs

Uponor Q&E M12 expander headsQ&E head for S5 fittings, for M12 and M18 tools.Expander head packed screw pack


1057172 16 14 6+10 Uponor Q&E M12 expander head16x1.8/2.0/2.2 mm 1 pcs

1057173 20 14 6 Uponor Q&E M12 expander head20x1.9/2.0 mm 1 pcs

1057175 25 14 6 Uponor Q&E M12 expander head25x2.3 mm 1 pcs


stroke [mm] p [bar]

14 6

stroke [mm] p [bar]

25 6


Uponor tools

Uponor Q&E M18 expander headsQ&E head for S5 fittings, for M18 tools.Expander head packed screw pack


1057178 20 25 6 Uponor Q&E M18 expander headH20x1.9/2.0 mm 1 pcs

1057180 25 25 6 Uponor Q&E M18 expander headH25x2.3 mm 1 pcs

1057183 40 25 6 Uponor Q&E M18 expander headH40x3.7 mm 1 pcs

Uponor Q&E M12 batteryQ&E M12 rechargeable Li-ion battery for M12 tool.Battery 1.5 AH


1057409 Uponor Q&E battery M121.5 AH 1 pcs

Uponor Q&E M12 chargerQ&E M12 charger for M12 tool Charger 220-240V / 50-60Hz

Item no. OV [V] Description unit

1057410 230 Uponor Q&E charger M12220-240V 1 pcs

Uponor Clip StaplerHigh-precision, wear-proof tool for pinning with staples in magazines, with curved magazine.


1002295 Uponor Clip stapler 1 pcs



Uponor tools

Uponor manual rollerFor sticking down of insulation sections and edges, takes a roll of tape.


1000142 Uponor manual roller 1 pcs

Uponor Q&E head graphite pasteColloidal graphite paste. For Uponor Q&E Tools.


1008334 Uponor graphite paste for Uponor plierscolloidal graphite paste, 30 g/tube 20 pcs

Uponor Twisting toolFor twisting of the tying wires while fixing the pipe on steel meshes.


1006243 Twisting tool for tying wire 1 pcs

Uponor cutter knifeCutter knife for polystyrene insulation.


1006263 Uponor polystyrene cutter knife 1 pcs

Uponor ring spanner wrenchFor swivel nut of the Uponor compression adapters

Item no. A/F [mm] Description unit

1006265 30 Uponor ring spanner wrenchfor wrench size 30 mm 1 pcs

Uponor door pipe ductExpansion rod with pipe laying mount


1007179 Uponor door pipe guide 1 pcs



Uponor tools

Uponor plastic manifold valve toolFor mounting and de-mounting the valves of the plastic manifold.


1009216 Uponor plastic manifold valve tool 1 pcs

Uponor Tying tool


1034533 Twisting tool for tying wire 1 pcs

Uponor pipe uncoiler with pipe guideFor laying of all Uponor pipes up to dimension 25 mm. Suits different pipe coils with 300 mm and 600 mm internal diameter.


1035807 Uponor pipe uncoiler with pipe guide 1 pcs

Uponor snow and ice decoilerUponor snow and ice melting, pipe decoiler.


1033691 Uponor Meltaway decoilerfor 25 x 2,3 mm pipe 1 pcs


International sales and delivery terms

Uponor Radiant Heating/Cooling > International sales and delivery terms

1 Interpretation

2 Basis of the sale

3 Orders and specifications

4 Price of Goods

5 Terms of payment

6 Delivery and Performance


International sales and delivery terms

Uponor Radiant Heating/Cooling > International sales and delivery terms

7 Risk and property

8 Liability

9 Insolvency of Buyer

10 Packing

11 General


Uponor Radiant Heating/Cooling > Item search register

Item search register

Item no. unit Page

1000002 m² 231000003 m² 231000012 pcs 201000015 m² 231000016 pcs 401000017 m² 23, 331000018 m 241000019 pcs 241000079 m 391000080 m 391000081 m 391000082 pcs 391000083 pcs 401000084 l 401000085 l 411000138 pcs 591000142 pcs 1031000296 pcs 911000297 pcs 921000298 pcs 921000299 pcs 921000300 pcs 921000301 pcs 921000303 pcs 921000304 pcs 921000310 pcs 931000311 pcs 941000312 pcs 951000313 pcs 951000314 pcs 951000502 pcs 521000503 pcs 521000504 pcs 521000505 pcs 521000515 pcs 541000516 pcs 661000517 pcs 661000518 pcs 541000527 pcs 531000529 pcs 541000531 pcs 561000533 pcs 561000535 pcs 571000536 pcs 571000537 pcs 591000538 pcs 531000539 pcs 571001369 pcs 991002295 pcs 1021002296 pcs 231002297 pcs 231002356 pcs 661002357 pcs 661005049 m² 12, 33, 401005066 l 41

Item no. unit Page

1005084 m² 331005087 m² 331005100 set 461005168 pcs 471005170 pcs 471005261 m² 91005263 pcs 9, 37, 981005264 pcs 9, 36, 971005265 pcs 9, 37, 971005266 pcs 461005267 m 101005268 m 101005269 pcs 10, 401005274 m 10, 361005284 pcs 851005286 pcs 851005287 pcs 33, 74, 811005289 pcs 741005290 m 73, 811005291 pcs 73, 811005295 pcs 72, 821005296 pcs 72, 821005297 pcs 72, 821005298 pcs 72, 821005358 m 731005372 pcs 74, 811005477 m² 151005478 m² 151005479 m 151005480 m 151005481 m 161005482 pcs 161005483 m 161005484 m 161005485 m² 121005486 pcs 121005498 m 241005576 pcs 681005605 pcs 611005675 set 681006243 pcs 1031006247 set 1001006263 pcs 1031006265 pcs 1031006290 pcs 991006636 pcs 991006637 pcs 991006639 pcs 991006640 pcs 991006641 pcs 461007082 pcs 1001007179 pcs 1031007226 m² 201007228 m² 201007232 m² 20

Item no. unit Page

1007234 m² 201008334 pcs 1031008671 pcs 72, 841008673 pcs 861008683 pcs 861008932 pcs 721008939 m 861009004 pcs 481009006 pcs 74, 82, 871009129 pcs 381009132 pcs 381009209 set 441009214 set 441009215 set 441009216 pcs 1041009217 pcs 441009222 pcs 33, 74, 821009226 m 17, 25, 341009227 m 17, 25, 341009228 m 25, 34, 361009230 m 25,34,36,72,97

1009231 m 25,34,36,72,97

1009233 pcs 48, 741012869 m 74, 82, 871013005 pcs 601013006 pcs 611013008 pcs 591013051 pcs 451013052 pcs 451013053 pcs 451013054 pcs 451013055 pcs 451013056 pcs 451013057 pcs 451013058 pcs 451013059 pcs 451013060 pcs 451013061 pcs 451013062 pcs 451013063 pcs 451013064 pcs 451013065 pcs 451013066 pcs 451013067 pcs 451013068 pcs 451013069 pcs 451013070 pcs 451013071 pcs 451013072 pcs 451013127 m 241013366 m 13, 18, 26, 31

1013371 m 18, 26, 311013378 m 18, 26, 311013380 m 18, 26, 311013392 m 26




Item no. unit Page

1014122 pcs 471015154 pcs 13, 18, 26, 31

1015164 pcs 18, 21, 26, 31

1015187 pcs 261015764 pcs 1001015776 set 1001015777 set 1001015780 set 1001016699 m² 281016700 m² 291016701 m² 291016702 m² 301016703 m² 281016724 pcs 991020506 pcs 971020518 pcs 37, 981020524 pcs 37, 981022341 m 781022983 pcs 901022984 pcs 901022985 pcs 931022986 pcs 931022987 pcs 911022988 pcs 931023006 pcs 731023007 pcs 73, 841023008 pcs 73, 841023011 pcs 731023012 pcs 73, 841023013 pcs 73, 841023448 m 72, 841030134 pcs 761030135 set 761030580 pcs 431030581 pcs 431030582 pcs 431030583 pcs 431030584 pcs 431030585 pcs 431032701 set 461032702 set 441033024 m 9, 361033025 m 9, 361033026 m 9, 361033625 m 781033626 m 781033628 m 791033629 m 791033630 m 791033631 pcs 781033632 pcs 781033633 pcs 781033634 pcs 791033635 pcs 791033636 pcs 79

Item no. unit Page

1033637 pcs 781033638 pcs 781033639 pcs 781033640 pcs 781033641 pcs 781033642 pcs 781033643 pcs 781033644 pcs 791033645 pcs 781033646 pcs 791033647 pcs 781033648 pcs 791033649 pcs 791033650 pcs 791033652 pcs 801033653 pcs 801033654 pcs 801033657 pcs 801033659 pcs 801033660 pcs 801033661 pcs 801033662 pcs 801033663 pcs 801033666 pcs 811033667 pcs 811033668 pcs 811033672 pcs 791033673 pcs 811033675 pcs 811033676 pcs 811033678 pcs 791033689 pcs 821033691 pcs 1041033975 pcs 481034533 pcs 1041034535 m 17, 25, 341035807 pcs 1041042389 pcs 18, 21, 26, 31

1042420 set 431042471 set 431042836 pcs 79, 981042837 pcs 26, 34, 371042840 pcs 73, 841042942 pcs 931042943 pcs 931042944 pcs 931042945 pcs 931042946 pcs 941042947 pcs 941044181 pcs 331044809 pcs 931044810 pcs 931044811 pcs 931044812 pcs 931045315 pcs 89

Item no. unit Page

1045316 pcs 891045317 pcs 891045318 pcs 891045319 pcs 901045320 pcs 901045323 pcs 901045324 pcs 901045325 pcs 911045326 pcs 911045327 m 911045328 pcs 911045464 pcs 861045562 set 511045565 pcs 511045568 pcs 521045570 pcs 531045571 pcs 541045572 pcs 531045813 set 751045814 set 751045815 set 751045816 set 761046114 pcs 521046115 pcs 521046747 set 851046748 set 851046749 set 851046870 pcs 681046991 pcs 481046992 pcs 481046993 pcs 481046994 pcs 481046996 pcs 491046997 pcs 491046998 pcs 491046999 pcs 491047000 pcs 481047319 pcs 971047320 pcs 971047321 pcs 971047610 m 17, 25, 301047611 m 17, 25, 301047612 m 17, 25, 301047615 m 72, 841047618 m 72, 841047624 m 211047625 m 211047844 pcs 641047845 pcs 651047846 pcs 651047847 pcs 661047848 pcs 661047867 pcs 861048010 pcs 561048011 pcs 58




Item no. unit Page

1048012 pcs 581048013 pcs 591048249 m 211048290 m 12, 17, 25, 30

1048291 m 12, 17, 25, 30

1048395 m 211048684 pcs 921048685 pcs 921048763 pcs 661048780 pcs 691048781 pcs 691048782 pcs 701048783 pcs 701052123 pcs 801056656 pcs 801057166 set 1011057169 set 1011057172 pcs 1011057173 pcs 1011057175 pcs 1011057178 pcs 1021057180 pcs 1021057183 pcs 1021057184 pcs 1011057185 pcs 1011057368 pcs 471057370 pcs 471057409 pcs 1021057410 pcs 1021057441 pcs 471057442 pcs 471058089 pcs 471058090 pcs 471058091 pcs 471058092 pcs 471058422 pcs 601058423 pcs 601058424 pcs 611058425 pcs 611058426 pcs 601058427 pcs 601058428 pcs 13, 18, 26, 31

1058429 pcs 18, 26, 341058659 pcs 13, 18, 26, 31

1058660 pcs 18, 21, 26, 31

1058661 pcs 18, 26, 341058668 pcs 26, 34



Notes

How to contact us


Customer Service Center T + 49 (0)9521-690-370 F + 49 (0)9521-690-750 E [email protected]

Technical assistance T +49 (0)9521-690-739 or 834 F +49 (0)9521-690-750 E [email protected]

Export Department T +49 (0)9521-690-370 F +49 (0)9521-690-750 E [email protected]

We reserve the right to make technical amendments and carry out updates.

Uponor – partnering with professionals

Uponor is a leading supplier of plumbing and heating systems for the residential and commercial building markets across Europe and North America, and a market leader in municipal infrastructure pipe systems in the Nordic countries. Uponor's key applications include indoor climate and plumbing systems.

Uponor International Sales takes care of all business activities in the Balkans, Western, Central and East Asia, Africa and Latin America.

Uponor. Simply more.

01/2

012

– Su

bjec

t to

mod

ifi ca

tions

Uponor GmbHP.O. Box 164197433 HassfurtGermanyT +49-(0)9521 690 0F +49-(0)9521 690 750E [email protected] www.uponor.com/international

Date post:	30-Mar-2016
Category:	Documents
Upload:	uponor-international
View:	253 times
Download:	6 times

1042641 uponor pc ic is 2012

Documents