Page 8
@Perkins
1300 Edi Series-Electropack
1500/50 Hertz, can be wired 3 ways,(auto or manual, (load share) or stand alone, (isochronous)
1800/60Hertz, can be wired 3 ways(auto or manual, (load share) or stand alone, (isochronous)
1500/1800 Switchable, can be wired 2 ways1500 or 1800, Isochronous Only
12 Volt and 24 Volt ECM’s available.If you are not sure of the voltage and the markings have been removed
check PIN 35 to ground 1.4K Ohms – 12 volts / 2.8K Ohms – 24 volts.
Notes:On start up for genset applications the ECM automatically determines which speed/loadsignal ‘out of range’ (o.o.r.) fault management to use. This is dependant on the wiringconfiguration it observesStand alone (isochronous) operation – APS & RPS inputs are both inactive. Manual synchronised load sharing – APS input is active, RPS input is inactive. Automatic synchronised load sharing – APS input is inactive, RPS input is active. 2 way protection is achieved by selecting 3 way protection and ‘normally open (plastictank)’ for the CLS type. No connection should then be made to the CLS input.
6
Perkins G
en Set P
ower, T
PD
1440E, issue 2
95
1300 Series E
Di
Wirin
g d
iagram
- Stan
d alo
ne (iso
chro
no
us) ru
nn
ing
W1361/1
1
Attention
Note: Power supply for ECM mustbe taken directly from the battery,not the starter motor terminal.
1
Clear wire
18 AWG
87
85
Chassis harness connectorInterface harness
(if used)
See note 5
18 AWG
18 AWG
18 AWG
18 AWG
18 AWG
18 AWG
18 AWG
14 AWG
14 AWG
14 AWG
14 AWG
14 AWG
14 AWG
14 AWG
18 AWG
5 AMP
5 AMP
18AWG
16 AWG
18 AWG
10 AWG
18 AWG
16 AWG
16 AWG
25
21
22
41
23
42
1
2
3732
16
17
55
54
24
34
10 AMP
10 AMP
Redlamp
Amberlamp
See note 6
See note 3
18 AW
G
Terminal can bemarked 87 or G
See note 4
Mainpower rly
See note 2
87a
86
30
30 AMP
10 AWG
On/off switch
16 AW
G
Diagnosticconnector
Black wire
ABEC
10AWG
Emergencystop device
Rating 30Amin
To starter andcharging circuits
Battery
+
-
Battery
+
-
12V or 24V
Power relay out
DC/DC Converter
(+) Feed
HSO (+) Feed
HSO Ground feed
DPS O/P’s Ground feed
DC/DC Converter
Ground feed
PRE InputSCS Input (set coast)
ATA (+)
ATA (-)
ENG Warn light output
Oil water lamp output
VIGN - IPR (+) Feed
STI Switch
(Data link J1708)
ECM
Diagnosticswitch
Notes
1)
2)
3)
4)
5)
6)
Wire sizing:10AWG (approx. 5mm ) Main feed and return to battery14AWG (approx. 2mm ) ECM pin Nos 21.22.41.23.42.1.216AWG (approx. 1mm ) Ignition and diagnostic socket supply18AWG (approx. 0.8mm ) All other circuits
Main Power Relay12V part no. 1688314C1(12V alternative part no’s. 2848A203)
24V part no. 2848A226
Where shown, cables must be twisted together (360 per 25 mm andscreened to minimise noise effects. Connect screen at one end only.
All fuses must comply with SAE J1284 and be located close to thebattery so as to protect the wiring.
All unused interface harness cables must be insulated.
Recommended rating for lamps is between 2 and 2.2 watts.
2
2
2
2
0
6 96P
erkins Gen S
et Pow
er, TP
D 1440E
, issue 2
1300 Series E
Di
Wirin
g d
iagram
- Man
ual syn
chro
nised
load
sharin
g
W1362/1
1
Attention
Note: Power supply for ECM mustbe taken directly from the battery,not the starter motor terminal.
Notes
1)
2)
3)
4)
5)
6)
7)
Wire sizing:10AWG (approx. 5mm ) Main feed and return to battery14AWG (approx. 2mm ) ECM pin Nos 21.22.41.23.42.1.216AWG (approx. 1mm ) Ignition and diagnostic socket supply18AWG (approx. 0.8mm ) All other circuits
Main Power Relay12V part no. 1688314C1(12V alternative part no’s. 2848A203)
24V part no. 2848A226
Where shown, cables must be twisted together (360 per 25 mm andscreened to minimise noise effects. Connect screen at one end only.
All fuses must comply with SAE J1284 and be located close to thebattery so as to protect the wiring.
All unused interface harness cables must be insulated.
Recommended rating for lamps is between 2 and 2.2 watts.
Where shown, cables must be twisted together (360 per 25 mm a
2
2
2
2
0
0
1
Clear wire
18 AWG
87
85
Chassis harness connectorInterface harness (if used)
See note 5
18 AWG
18 AWG
18 AWG
18 AWG
14 AWG
14 AWG
14 AWG
14 AWG
14 AWG
14 AWG
14 AWG
18 AWG
5 AMP
18AWG
16 AWG
10 AWG
18 AWG
16 AWG
16 AWG
25
21
22
41
23
42
1
2
16
17
55
54
24
10 AMP
10 AMP
Red lamp
Amber lampSee note 6
See note 3
Terminal can bemarked 87 or G
See note 4
Mainpower rly
See note 2
87a
86
30
30 AMP
10 AWG
On/off switch
16 AW
G
Diagnosticconnector
Black wire
ABEC
10AWG
Emergencystop device
Rating 30Amin
To starter andcharging circuits
Battery
+
-
Battery
+
-
12Vor
24V
Power relay out
DC/DC Converter
(+) Feed
HSO (+) Feed
HSO Ground feed
DPS O/P’s Ground feed
DC/DC Converter
Ground feed
ATA (+)
ATA (-)
ENG Warn light output
Oil water lamp output
VIGN - IPR (+) Feed
(Data link J1708)
ECM
18 AWG18 AWG34 STI Switch
Diagnosticswitch
3
8
11
VBREF (5V) Sensor supply
APS InputVBREF GND Sensor supply
See note 7Seenote 3
250Ohms
2 KOhms
250Ohms
Manual speed(demand) signal.(working range0.5 to 4.5 voltsinto ECM pin 8).All resistors ratedat 0.25 watts.
6
Perkins G
en Set P
ower, T
PD
1440E, issue 2
97
1300 Series E
Di
Wirin
g d
iagram
- Au
tom
atic synch
ron
ised lo
ad sh
aring
W1363/1
1
Clear wire18 AWG
87
85
Chassis harness connectorInterface harness (if used)
See note 5
18 AWG
18 AWG
18 AWG
18 AWG
14 AWG
14 AWG
14 AWG
14 AWG
14 AWG
14 AWG
14 AWG
18 AWG
5 AMP
18AWG
16 AWG
10 AWG
18 AWG
16 AWG
16 AWG
25
21
22
41
23
42
1
2
16
17
55
5410 AMP
10 AMP
Redlamp
Amberlamp
See note 6
See note 3
Terminal can bemarked 87 or G
See note 4
Mainpower rly
See note 2
87a
86
30
30 AMP
10 AWG
On/off switch
16 AW
G
Diagnosticconnector
Black wire
ABEC
10AWG
Emergencystop device
Rating 30Amin
To starter andcharging circuits
Battery
+
-
Battery
+
-
12V or 24V
Power relay out
DC/DC Converter
(+) Feed
HSO (+) Feed
HSO Ground feed
DPS O/P’s Ground feed
DC/DC Converter
Ground feed
ATA (+)
ATA (-)
ENG Warn light output
Oil water lamp output
VIGN - IPR (+) Feed
(Data link J1708)
ECM
18 AWG18 AWG34 STI Switch
Diagnosticswitch
3
11
VBREF (5V) Sensor supply
RPS Input
VBREF GND Sensor supplySee note 7
Auto speed(demand)
signal
Working inputvoltage into ECM
pin 30 is 0.5 to 4.5
30
37
24
RPRE Input
5 AM
P
18 AWG
1
Attention
Note: Power supply for ECM mustbe taken directly from the battery,not the starter motor terminal.
Notes
1)
2)
3)
4)
5)
6)
7)
Wire sizing:10AWG (approx. 5mm ) Main feed and return to battery14AWG (approx. 2mm ) ECM pin Nos 21.22.41.23.42.1.216AWG (approx. 1mm ) Ignition and diagnostic socket supply18AWG (approx. 0.8mm ) All other circuits
Main Power Relay12V part no. 1688314C1(12V alternative part no’s. 2848A203)
24V part no. 2848A226
Where shown, cables must be twisted together (360 per 25 mm andscreened to minimise noise effects. Connect screen at one end only.
All fuses must comply with SAE J1284 and be located close to thebattery so as to protect the wiring.
All unused interface harness cables must be insulated.
Recommended rating for lamps is between 2 and 2.2 watts.
Where shown, cables must be twisted together (360 per 25 mm a
2
2
2
2
0
0
6 98P
erkins Gen S
et Pow
er, TP
D 1440E
, issue 2
1300 Series E
Di
Wirin
g d
iagram
- 1500/1800 rev/min
Sw
itchab
le stand
alon
e isoch
ron
ou
s (no
n-lo
ad sh
aring
)
W1364/1
1
Clear wire18 AWG
87
85
Chassis harness connectorInterface harness (if used)
See note 5
18 AWG
18 AWG
18 AWG
18 AWG
18 AWG
18 AWG
18 AWG
14 AWG
14 AWG
14 AWG
14 AWG
14 AWG
14 AWG
14 AWG
18 AWG
5 AMP
5 AMP
18AWG
16 AWG
18 AWG
10 AWG
18 AWG
16 AWG
16 AWG
25
21
22
41
23
42
1
2
37
32
16
17
55
54
24
34
10 AMP
10 AMP
Redlamp
Amberlamp
See note 6
See note 3
18 AW
G
Terminal can bemarked 87 or G
See note 4
Mainpower rly
See note 2
87a
86
30
30 AMP
10 AWG
On/off switch
16 AW
G
Diagnosticconnector
Black wire
ABEC
10AWG
Emergencystop device
Rating 30Amin
To starter andcharging circuits
Battery
+
-
Battery
+
-
12V or 24V
Power relay out
DC/DC Converter
(+) Feed
HSO (+) Feed
HSO Ground feed
DPS O/P’s Ground feed
DC/DC Converter
Ground feed
PRE Input
SCS Input (set coast)
ATA (+)
ATA (-)
ENG Warn light output
Oil water lamp output
VIGN - IPR (+) Feed
STI Switch
(Data link J1708)
ECM
Diagnosticswitch
J1
18 AWGJ231 RAS Input (resume/accel)
See note 71
Attention
Note: Power supply for ECM mustbe taken directly from the battery,not the starter motor terminal.
Notes
1)
2)
3)
4)
5)
6)
7)
Wire sizing:10AWG (approx. 5mm ) Main feed and return to battery14AWG (approx. 2mm ) ECM pin Nos 21.22.41.23.42.1.216AWG (approx. 1mm ) Ignition and diagnostic socket supply18AWG (approx. 0.8mm ) All other circuits
Main Power Relay12V part no. 1688314C1(12V alternative part no’s. 2848A203)
24V part no. 2848A226
Where shown, cables must be twisted together (360 per 25 mm andscreened to minimise noise effects. Connect screen at one end only.
All fuses must comply with SAE J1284 and be located close to thebattery so as to protect the wiring.
All unused interface harness cables must be insulated.
Recommended rating for lamps is between 2 and 2.2 watts.
Genset speed settings.For 1500 rpm connect link J1For 1800 rpm connect link J2
2
2
2
2
0
6
Perkins G
en Set P
ower, T
PD
1440E, issue 2
99
1300 Series E
Di
Wirin
g d
iagram
- Gen
Set o
ptio
ns
W1365
10 AMP
87
85
Radiatorshutter
control relay
87a
86
30
See note 3
AB
Two pinconnector
Single pinconnector
11
9
Snooze (run enable)
Radiator shutter
Engine harness connector
Chassis harness connector
54 OWL Output (press/temp)
10 Coolant level switch
Snooze
10 AMP
See note 2
Coolantlevel
switchRequest toshutdown
See note 1
RedOn/off
Battery
+
-
Battery
+
-
Vbal
Emergencystop
Standard operating mode circuit
Additional notes
1) Maximum total current from OWL (54) output = 1 Amp (including lamp and ’request to shutdown’ signal).
2) Coolant level sensor operation depends on EPN option selected ’normally closed (metal tank)’ ’narmally open (plastic tank)’.
3) Customers must specify the relay, the wiring and appropriate fuses for the radiator shutter control circuit.
Snooze (run enable) single pin connector:Packard part # Description12065171...............Mating connector12065249...............Secondary lock12048159...............Male terminal 18 - 16 AWG