13.02 Stainless Steel Piping

Printouts, if any, are not controlled. Printed on: 23/01/2018

Mondi Štětí a.s.

STANDARD

Part 13.02

STAINLESS STEEL PIPING

Mondi Štětí a.s. STANDARD 13.02 Page: 1/44

Version: 1 Valid from: 18.1.2018


STANDARD

Part 13.02

STAINLESS STEEL PIPING

Worked out by: Verified by: Approved by: Name: Name: Name: Position: Position: Position: Signed by: Signed by: Signed by:




CONTENT 13.02.01 Pipe classes 0H...63H 13.02.02 Allowable pressures at elevated temperatures 13.02.03 Pipes for pipe classes 6H...63H 13.02.04 Vacuum pipes, pipe class 0H 13.02.05 Elbows for pipe classes 0H...63H 13.02.06 Reducers for pipe classes 0H...63H 13.02.07 Tee pieces for pipe classes 0H...63H 13.02.08 Reinforced branch connections – allowable pressures 13.02.09 Reinforced branch connection with plate 13.02.10 Blank flange 0H...25H 13.02.11 Spade blank 13.02.12 Open spade 13.02.13 Plate valve 13.02.14 Drain and spooling connection DN 40 and DN 50 13.02.15 Vent connection DN 25 13.02.16 Sample taking connection DN 40




TABLE OF CONTENTS Page

1 Pipe classes 0H…63H ............................................................................................................ 4

2 Allowable pressures at elevated temperatures ................................................................... 8 3 Pipes for pipe classes 6H...63H........................................................................................... 10

4 Vacuum pipes, pipe class 0H ............................................................................................... 12 5 Elbows for Pipe Classes 0H...63H ...................................................................................... 14

6 Reducers for pipe classes 0H...63H ................................................................................... 16 7 Tee pieces for pipe classes 0H...63H ................................................................................. 21

8 Reinforced branch connections – allowable pressures ................................................... 25

9 Reinforced branch connection with plate ........................................................................... 32

10 Blank flange 0H...25H ........................................................................................................... 34

11 Spade blank ............................................................................................................................ 35 12 Open spade ............................................................................................................................. 37

13 Plate valve ............................................................................................................................... 39 14 Drain and spooling connection DN 40 and DN 50 ............................................................ 41 15 Vent connection DN 25 ......................................................................................................... 43

16 Sample taking connection DN 40 ........................................................................................ 44

http://portal/Docs/ControlledDocumentationIMS/Úseky/Údržba/Standardy.xls

http://portal/Docs/ControlledDocumentationIMS/Úseky/Údržba/Standardy.xls

Mondi Štětí a.s. STANDARD 13.02.01 Page: 4/44



1 Pipe classes 0H…63H

1.1 General This standard presents dimension standards and material specifications for piping components of normal stainless steel pipe classes. 1.2 Pipe classes

Pipe

class

0H2A

0H1A

6H2A

6H1A

10H3A

10H2A

10H1A

16H3A

16H2A

16H1A

25H3A

25H2A

25H1A

40H2A

40H1A

63H2A

63H1A

Design pressure1)

(MPa) at 20 °C

0 (abs)

0.6

1.0

1.6

2.5

4.0

6.3

1) Design pressure is internal overpressure (pe), except for pipe classes 0H1A and 0H2A where design pressure 0 refers to absolute pressure = 0.1 MPa external pressure (full vacuum)




1.3 Piping components for 0H1A...63H1A

Piping components

Dimension standard

Material Remarks

4) Designation Standard Certificate

EN 10204-

Pipe EN 10217-7,

13.02.03

1.4307 EN 10217-7 3.1

Vacuum pipe EN 10217-7,

13.02.04

1.4307 EN 10217-7 3.1

Elbow EN 10253-4,

13.02.05

1.4307 EN 10253-4 3.1

Reducer EN 10253-4,

13.02.06

1.4307 EN 10253-4 3.1

Tee piece EN 10253-4,

13.02.07

1.4307 EN 10253-4 3.1

Collar EN 1092-1

Type 35 ,PN 10…40

1.4307 EN 10028-7 3.1

Flange EN 1092-1

Type 02, PN 10…40

Type 11-B11 PN 63

P265GH

1.4307

EN 10028-2

EN 10222-5

3.1

Hot dip galvanized

-

Blank flange EN 1092-1 Type 05/ lining plate,

PN 10…63

13.02.10

P265GH/

1.4307 lining plate

EN 10028-2/

EN 10028-7

3.1

3.1

Hot dip galvanized

with 1.4307 plate

Blank and open spade 13.02.11/12 P265GH/

1.4307 lining plate

EN 10028-2/

EN 10028-7

3.1

3.1

Plate valve 13.02.13 1.4307 EN 10217-7 3.1

Cap EN 10253-4,

Wall thickness same as pipe wall thickness

1.4307 EN 10253-4 3.1

Hex head bolt 3) EN ISO 4014 8.8 5), (T< 300°C)

25CrMo4

EN ISO 898-1

EN 10269

2.2

3.1

Hot dip galvanized

-

Nut 3) EN ISO 4032 8 5) (T< 300°C)

C35E

EN ISO 898-2

EN 10269

2.2

3.1

Hot dip galvanized

-

Washer ISO 7089 Gr. A S 235JR EN 10025-2 Hot dip galvanized

Gasket EN 1514-1 Type IBC

PN 10…63 1)

2)

Threaded fittings EN 10241 1.4404 EN 10272 3.1 Thread according to ISO 7-1 (R thread)

Not for 63H1A

1) Gasket thickness 2.0 mm 2) Gasket material depends on flow substance. See 13.01.01 “Technical Specification for Flow Substances, Pipe and Valve Type

Selection”. 3) Material for hexagon head bolts in pipe class 63H1A is 25CrMo4 and nuts C35E according to EN 10269. 4) Weld joint coefficient=1 5) Starting material shall comply with EN 10269. Material certificate from base material.





Piping components

Dimension standard

Material Remarks


EN 10204-

Pipe EN 10217-7,

13.02.03

1.4404 EN 10217-7 3.1


13.02.04

1.4404 EN 10217-7 3.1

Elbow EN 10253-4,

13.02.05

1.4404 EN 10253-4 3.1

Reducer EN 10253-4,

13.02.06

1.4404 EN 10253-4 3.1


13.02.07

1.4404 EN 10253-4 3.1

Collar EN 1092-1

Type 35 ,PN 10…40

1.4404 EN 10028-7 3.1

Flange EN 1092-1

Type 02, PN 10…40

Type 11-B11 PN 63

P265GH

1.4404

EN 10028-2

EN 10222-5

3.1

Hot dip galvanized

-


PN 10…63

13.02.10

P265GH/

1.4404 lining plate

EN 10028-2/

EN 10028-7

3.1

3.1

Hot dip galvanized

with 1.4404 plate

Blank and open spade 13.02.11/ 12 P265GH/

1.4404 lining plate

EN 10028-2/

EN 10028-7

3.1

3.1

Plate valve 13.02.13 1.4404 EN 10217-7 3.1

Cap EN 10253-4,


1.4404 EN 10253-4 3.1

Hex head bolt 3) EN ISO 4014 8.8 5), (T< 300°C)

25CrMo4

EN ISO 898-1

EN 10269

2.2

3.1

Hot dip galvanized

-

Nut 3) EN ISO 4032 8 5) (T< 300°C)

C35E

EN ISO 898-2

EN 10269

2.2

3.1

Hot dip galvanized

-



PN 10…63 1)

2)

Threaded fittings EN 10241 1,4404 EN 10272 3.1 Thread according to ISO 7-1 (R thread)

Not for 63H2A


Selection”. 3) Material for hexagon head bolts in pipe class 63H2A is 25CrMo4 and nuts C35E according to EN 10269. 4) Weld joint coefficient=1 5) Starting material shall comply with EN 10269. Material certificate from base material.





Piping components

Dimension standard

Material Remarks


EN 10204-

Pipe EN 10217-7,

13.02.03

1.4462

(duplex)

EN 10217-7 3.1


13.02.04

1.4462

(duplex)

EN 10217-7 3.1

Elbow EN 10253-4,

13.02.05

1.4462

(duplex)

EN 10253-4 3.1

Reducer EN 10253-4,

13.02.06

1.4462

(duplex)

EN 10253-4 3.1


13.02.07

1.4462

(duplex)

EN 10253-4 3.1

Collar EN 1092-1

Type 35 ,PN 10…25

1.4462

(duplex)

EN 10028-7 3.1

Flange EN 1092-1

Type 02, PN 10…25

P265GH

EN 10028-2

3.1

Hot dip galvanized


PN 10…25

13.02.10

P265GH/

1.4462 lining plate

(duplex)

EN 10028-2/

EN 10028-7

3.1

3.1

Hot dip galvanized

with 1.4462 plate

Blank and open spade 13.02.11/ 12 P265GH/

1.4462 lining plate

(duplex)

EN 10028-2/

EN 10028-7

3.1

3.1

Hot dip galvanized

with 1.4462 plate

Plate valve 13.02.13 1.4462

(duplex)

EN 10217-7 3.1

Cap EN 10253-4,


1.4462

(duplex)

EN 10253-4 3.1

Hex head bolt EN ISO 4014 8.8 5), (T< 300°C)

25CrMo4

EN ISO 898-1

EN 10269

2.2

3.1

Hot dip galvanized

-

Nut EN ISO 4032 8 5) (T< 300°C)

C35E

EN ISO 898-2

EN 10269

2.2

3.1

Hot dip galvanized

-



PN 10…25 1)

2)

Threaded fittings EN 10241 1,4462 or equal EN 10272 3.1 Thread according to ISO 7-1 (R thread)


Selection”. 3) Weld joint coefficient=1

4) Starting material shall comply with EN 10269. Material certificate from base material.




2 Allowable pressures at elevated temperatures 2.1 General This standard gives the coefficient k for defining the allowable pressures at elevated temperatures generally for Pipe classes and in detail for branch connections presented in standard 13.02.08. 2.2 Limitations The allowable pressure shall not exceed the nominal pressure of Pipe Classes 6H...63H. 2.3 Coefficient k

Temperature oC

k coefficient for material grades

1.4307 1.4404 1.4462

20 1 1 1

50 0,93 0,96 0,92

75 0,89 0,92 0,86

100 0,84 0,88 0,80

125 0,80 0,84 0,77

150 0,75 0,80 0,74

175 0,72 0,77 0,72

200 0,68 0,74 0,69

where 1.4307 corresponds to H1 1.4404 corresponds to H2 1.4462 corresponds to H3 2.4 Examples

Example 1: Pipe Class 25H2A Temperature = 150 ºC Coefficient k = 0.8 The allowable pressure = 0.8 x 25 bar = 20 bar, which means that all components of that Pipe Class 25H2A stand the pressure 2.0 MPa.




Example 2:

Pipe class 6H1A Temperature = 20 ºC Coefficient k = 1.00 The allowable pressure = 1.00 x 6 bar = 6.0 bar, which means that the Pipe Class can be used up to 0.6 MPa. Example 3: Reinforced branch connection with plate reinforcement of Pipe Class 16H, DN 800/ DN 500 Temperature = 150 ºC Coefficient k = 0.80 Allowable pressure from standard 02-011 is 1.62 MPa The allowable pressure = 0.8 x 1.62 MPa = 1.29 MPa, which means that the reinforced branch connection stands the pressure 1.29 MPa.




3 Pipes for pipe classes 6H...63H

3.1 Dimensions

DN Do x s

0H 1),

6H

10H 16H 25H 40H 63H

6 10.2 x 1.6

10 17.2 x 1.6 According to

15 21.3 x 1.6 According to 6H



(32) 42.4 x 1.6 According to 6H

40 48.3 x 1.6 6H

50 60.3 x 1.6 60.3 x 2.0

(65) 76.1 x 1.6 76.1 x 2.6

80 88.9 x 2.0 88.9 x 3.2

100 114.3 x 2.0 114.3 x 2.6 114.3 x 4.0

(125) 139.7 x 2.0 139.7 x 3.2 139.7 x 5.0

150 168.3 x 2.0 168.3 x 2.6 168.3 x 4.0 168.3 x 6.3

200 219.1 x 2.0 219.1 x 3.2 219,1 x 5.0

250 273 x 2.0 273 x 2.6 273 x 4.0 273 x 6.3

300 323.9 x 2.6 323.9 x 3.2 323.9 x 5.0

350 355.6 x 2.6 355.6 x 3.2 355.6 x 5.0

400 406.4 x 3.2 406.4 x 4.0 406.4 x 6.3

(450) 457 x 3.2 457 x 5.0 457 x 8.0

500 508 x 4.0 508 x 6.3 508 x 10

600 610 x 4.0 610 x 5.0 610 x 8.0 610 x 12.5

700 711 x 4.0 711 x 5.0 711 x 8.0 711 x 12.5

800 813 x 4.0 813 x 6.3 813 x 10 813 x 12.5

900 914 x 4.0 914 x 8.0 914 x 10

1000 1016 x 5.0 1016 x 8.0 1016 x 12,5

1200 1220 x 6.3 1220 x 10

The nominal sizes inside parenthesis shall be avoided. 1) Reinforcement rings against vacuum are presented in the standard

13.02.04.




3.2 Designation Name, Do x s, material, standard No. Example: Pipe, 114.3 x 2.0, 1.4404, EN 10217-7




4 Vacuum pipes, pipe class 0H 4.1 Dimensions

DN Do s Lmax b x h

200 219.1 2.0 2000 30 x 6

250 273 2.0 1700 30 x 6

300 323.9 2.6 2200 30 x 6

350 355.6 2.6 2300 35 x 8

400 406.4 3.2 2800 40 x 8

(450) 457 3.2 2800 40 x 8

500 508 4.0 3500 50 x 8

600 610 4.0 2600 60 x 6

700 711 4.0 2300 60 x 6

800 813 4.0 1700 60 x 6

900 914 4.0 1500 60 x 6

1000 1016 5.0 2200 70 x 8

1200 1220 6.3 2900 90 x 8




Notes: The effective throat thickness of fillet weld for the reinforcement ring is 0.7 x s, were s is the wall thickness of the pipe. Length of the welds on both sides of the ring must be at least 0.5 x circumference of the pipe. When using intermittent weld, the distance between welds must not exceed 8 x wall thickness of the pipe. Nominal sizes DN 6 - DN 150 do not need the reinforcement rings against vacuum when the wall thicknesses are according to the pipe class 6H. Extra reinforcement rings must be welded on to the pipe at both ends near bends. 4.2 Designation Name, Do x s, material, standard No. Example: Vacuum pipe, 406.4 x 3.2, 1.4404, 13.02.04




5 Elbows for Pipe Classes 0H...63H 5.1 Dimensions

Table 1 Dimensions according to pipe classes

DN

Do x s R Type

0H 6H

10H 16H 25H 1.5D 2.5D

6 10.2 x 2.0 R = 3...5D Elbow or bent pipe

10 17.2 x 2.0 28

15 21.3 x 2.0 According to 28 45

20 26.9 x 2.0 According to 6H 29 57

25 33.7 x 2.0 According to 6H 38 72

(32) 42.4 x 2.0 6H 48 93

40 48.3 x 2.0 57 108

50 60.3 x 2.0 76 135

(65) 76.1 x 2.0 95 175

80 88.9 x 2.0 114 205

100 114.3 x 2.0 114.3 x 2.6 152 270

(125) 139.7 x 2.0 139.7 x 3.2 190 330

150 168.3 x 2.0 168.3 x 2.6 168.3 x 4.0 229 390 R = 1.5D

200 219.1 x 2.0 219.1 x 3.2 219.1 x 5.0 305 510

250 273 x 2.0 273 x 2.6 273 x 4.0 273 x 6.3 381 650 Pressed elbow

300 323.9 x 2.6 323.9 x 3.2 323.9 x 4.0 323.9 x 6.3 457 775

350 355.6 x 2.6 355.6 x 3.2 355.6 x 4.0 355.6 x 6.3 533 850

400 406.4 x 3.2 406.4 x 4.0 406.4 x 5.0 406.4 x 8.0 610 970

(450) 457 x 3.2 457 x 4.0 457 x 6.3 457 x 10 686 1122

500 508 x 4.0 508 x 5.0 508 x 8.0 508 x 12.5 762 1245

600 610 x 4.0 610 x 6.3 610 x 10.0 610 x 12.5 914 1524

700 711 x 5.0 711 x 6.3 711 x 10.0 711 x 12.5 1067 R = 1.5D

800 813 x 5.0 813 x 8.0 813 x 12.5 813 x 14.2 1219 Mitre elbow

900 914 x 5.0 914 x 8.0 914 x 12.5 1372

1000 1016 x 6.3 1016 x 10 1016 x 12.5 1524

1200 1220 x 8.0 1220 x 12.5 1830




DN

Do x s

R

Type

40H 63H

10 17.2 x 1.6 According to 3...5D

15 21.3 x 2.0 40H 28 Bent

20 26.9 x 2.0 29 pipe

25 33.7 x 2.0 38 or elbow

(32) 42.4 x 2.0 42.4 x 3.2 48

40 48.3 x 2.0 48.3 x 3.2 57 R = 1.5D

50 60.3 x 2.6 60.3 x 4.0 76

(65) 76.1 x 3.2 76.1 x 5.0 95 Pressed elbow

80 88.9 x 3.2 88.9 x 5.0 114

100 114.3 x 5.0 114.3 x 6.3 152

(125) 139.7 x 5.0 139.7 x 6.3 190

150 168.3 x 6.3 168.3 x 8.0 229

200 219.1 x 8.0 305

250 273 x 10.0 381

The nominal sizes inside parenthesis shall be avoided. 5.2 Designation Name, Do x s, R, material, standard No. Example: Elbow, 219.1 x 2.0, 305, 1.4404, 13.02.05




6 Reducers for pipe classes 0H...63H 6.1 Dimensions

See the following table for dimensions.

L = 2.96 x (Do1 - Do2)

6.2 Sudden reducer Sudden reducer, type S, is to be used for pulp on the suction side of a pump when

consistency C is 4 %. Design of sudden reducer shall be verified with strength calculations by the Supplier. The given plate thickness of 10 mm is minimum requirement.




Type S




6.3 Dimensions for pipe classes 0H...63H

DN1

DN2

Do1

Do2

L Wall thickness s

mm mm mm 0H 6H

10H 16H 25H 40H 63H

25 10 15 20

33.7 17.2 21.3 26.9

49 37 20

2.0 2.0 2.0

According to 6H

According to 6H

(32) 10 15 20 25

42.4 17.2 21.3 26.9 33.7

75 62 46 26

2.0 2.0 2.0 2.0

According

According

to 6H

40 15 20 25 32

48.3 21.3 26.9 33.7 42.4

80 63 43 17

2.0 2.0 2.0 2.0

According

to 6H

2.6 2.6 2.6 2.6

50 20 25 32 40

60.3 26.9 33.7 42.4 48.3

99 79 53 36

2.0 2.0 2.0 2.0

to 6H

3.2 3.2 3.2 3.2

(65) 25 32 40 50

76.1 33.7 42.4 48.3 60.3

126 100 82 47

2.0 2.0 2.0 2.0

2.6 2.6 2.6 2.6

4.0 4.0 4.0 4.0

80 32 40 50

(65)

88.9 42.4 48.3 60.3 76.1

138 120 85 38

2.0 2.0 2.0 2.0

2.6 2.6 2.6 2.6

4.0 4.0 4.0 4.0

100 40 50

(65) 80

114.3

48.3 60.3 76.1 88.9

195 160 113 75

2.0 2.0 2.0 2.0

2.6 2.6 2.6 2.6

3.2 3.2 3.2 3.2

5.0 5.0 5.0 5.0

(125) 50

(65) 80 100

139.7

60.3 76.1 88.9 114.

3

235 188 151 75

2.0 2.0 2.0 2.0

2.6 2.6 2.6 2.6

4.0 4.0 4.0 4.0

6.3 6.3 6.3 6.3

150 (65) 80 100

(125)

168.3

76.1 88.9 114.

3 139.

7

273 234 160 85

2.0 2.0 2.0 2.0

3.2 3.2 3.2 3.2

5.0 5.0 5.0 5.0

8.0 8.0 8.0 8.0




DN1

DN2

Do1

Do2

L Wall thickness s / mm

mm mm mm 0H

6H

10H

16H 25H 40H

200 80 100 (125) 150

219.1 88.9 114.3 139.7 168.3

385 310 235 150

2.6 2.6 2.6 2.6

According

According

4.0 4.0 4.0 4.0

6.3 6.3 6.3 6.3

250 100 (125) 150 200

273.0 114.3 139.7 168.3 219.1

470 395 310 160

3.2 3.2 3.2 3.2

to 6H to 6H

5.0 5.0 5.0 5.0

8.0 8.0 8.0 8.0

300 (125) 150 200 250

323.9 139.7 168.3 219.1 273.0

545 461 310 151

3.2 3.2 3.2 3.2

5.0 5.0 5.0 5.0

350 150 200 250 300

355.6 168.3 219.1 273.0 323.9

554 404 244 94

3.2 3.2 3.2 3.2

4.0 4.0 4.0 4.0

5.0 5.0 5.0 5.0

400 200 250 300 350

406.4 219.1 273.0 323.9 355.6

554 395 244 150

3.2 3.2 3.2 3.2

4.0 4.0 4.0 4.0

6.3 6.3 6.3 6.3

(450) 250 300 350 400

457.0 273.0 323.9 355.6 406.4

545 395 301 150

4.0 4.0 4.0 4.0

6.3 6.3 6.3 6.3

10 10 10 10

500 300 350 400 (450)

508.0 323.9 355.6 406.4 457.0

545 451 301 150

4.0 4.0 4.0 4.0

5.0 5.0 5.0 5.0

6.3 6.3 6.3 6.3

10 10 10 10

600 350 400 (450) 500

610.0 355.6 406.4 457.0 508.0

752 601 451 301

4.0 4.0 4.0 4.0

5.0 5.0 5.0 5.0

8.0 8.0 8.0 8.0

12.5 12.5 12.5 12.5

700 400 (450) 500 600

711.0 406.4 457.0 508.0 610.0

902 752 601 301

4.0 4.0 4.0 4.0

6.3 6.3 6.3 6.3

10 10 10 10

12.5 12.5 12.5 12.5

800 (450) 500 600 700

813.0 457.0 508.0 610.0 711.0

1053 902 601 301

5.0 5.0 5.0 5.0

6.3 6.3 6.3 6.3

10 10 10 10

12.5 12.5 12.5 12.5

900 500 600 700 800

914.0 508.0 610.0 711.0 813.0

1203 902 601 301

5.0 5.0 5.0 5.0

8.0 8.0 8.0 8.0

10 10 10 10

1000 600 700 800 900

1016.0 610.0 711.0 813.0 914.0

1203 902 601 301

6.3 6.3 6.3 6.3

8.0 8.0 8.0 8.0

12,5 12,5 12,5 12,5

1200 700 800 900 1000

1220.0 711.0 813.0 914.0 1016.0

1506 1205 905 604

6.3 6.3 6.3 6.3

10.0 10.0 10.0 10.0




Note: The wall thickness of reducer is at least the same as the wall thicknesses of the pipe at the bigger end of the reducer, however at least 2 mm. 6.4 Designation Name, type, DN1/ DN2 x s, material, standard No. Example 1: Reducer, C, 500/ 350 x 4.0, 1.4404, EN 10253-4 Example 2: Reducer, S, 500/ 350 x 4.0, 1.4404, 13.02.06




7 Tee pieces for pipe classes 0H...63H 7.1 Dimensions

Dimensions are according to Table 1.




Table 1

DN1 DN2 Do1

mm

Do2

mm

L

mm

0H

6H s1 / s2

10H

s1 / s2

16H

s1 / s2

25H

s1 / s2

40H

s1 / s2

63H

s1 / s2

(32) 32 42.4 42.4 48 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.6

(32) 25 42.4 33.7 48 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.0

40 40 48.3 48.3 57 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 3.2 3.2

40 32 48.3 42.4 57 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 3.2 2.0

50 50 60.3 60.3 125 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.6 4.0 4.0

50 40 60.3 48.3 125 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.0 4.0 2.0

(65) 65 76.1 76.1 140 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.6 3.2 3.2 5.0 5.0

(65) 50 76.1 60.3 140 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.0 3.2 2.6 5.0 2.6

80 80 88.9 88.9 150 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.6 4.0 4.0 5.0 5.0

80 (65) 88.9 76.1 150 2.0 2.0 2.0 2.0 2.0 2.0 2.6 2.0 4.0 2.6 5.0 4.0

100 100 114.3 114.3 160 2.0 2.0 2.0 2.0 2.6 2.6 3.2 3.2 5.0 5.0 6.3 6.3

100 80 114.3 88.9 160 2.0 2.0 2.0 2.0 2.6 2.0 3.2 2.6 5.0 3.2 6.3 5.0

(125) 125 139.7 139.7 180 2.0 2.0 2.0 2.0 3.2 3.2 4.0 4.0 6.3 6.3 8.0 8.0

(125) 100 139.7 114.3 180 2.0 2.0 2.0 2.0 3.2 2.0 4.0 3.2 6.3 4.0 8.0 6.3

150 150 168.3 168.3 200 2.0 2.0 2.6 2.6 4.0 4.0 5.0 5.0 8.0 8.0 10.0 10.0

150 (125) 168.3 139.7 200 2.0 2.0 2.6 2.0 4.0 2.0 5.0 4.0 8.0 4.0 10.0 8.0

200 200 219.1 219.1 250 2.6 2.6 3.2 3.2 5.0 5.0 6.3 6.3 10.0 10.0

200 150 219.1 168.3 250 2.6 2.0 3.2 2.6 5.0 2.6 6.3 5.0 10.0 5.0

250 250 273.0 273.0 300 3.2 3.2 4.0 4.0 6.3 6.3 8.0 8.0 12.5 12.5

250 200 273.0 219.1 300 3.2 2.6 4.0 3.2 6.3 3.2 8.0 6.3 12.5 8.0

300 300 323.9 323.9 330 3.2 3.2 5.0 5.0 6.3 6.3 10.0 10.0

300 250 323.9 273.0 330 3.2 3.2 5.0 4.0 6.3 6.3 10.0 6.3

350 350 355.6 355.6 360 4.0 4.0 5.0 5.0 8.0 8.0 10.0 10.0

350 300 355.6 323.9 360 4.0 3.2 5.0 5.0 8.0 6.3 10.0 10.0




Table 1 (continues)

DN1 DN2 Do1

mm

Do2

mm

L

mm

0H

6H

s1 / s2

10H

s1 / s2

16H

s1 / s2

25H

s1 / s2

400 400 406.4 406.4 400 4.0 4.0 6.3 6.3 8.0 8.0 12.5 12.5

400 350 406.4 355.6 400 4.0 4.0 6.3 5.0 8.0 8.0 12.5 10.0

(450) 450 457.0 457.0 450 5.0 5.0 6.3 6.3 10.0 10.0 12.5 12.5

(450) 400 457.0 406.4 450 5.0 4.0 6.3 6.3 10.0 8.0 12.5 12.5

500 500 508.0 508.0 500 5.0 5.0 8.0 8.0 10.0 10.0 14.2 14.2

500 (450) 508.0 457.0 500 5.0 5.0 8.0 6.3 10.0 10.0 14.2 12.5

600 600 610.0 610.0 600 6.3 6.3 10.0 10.0 12.5 12.5 17.5 17.5

600 500 610.0 508.0 600 6.3 5.0 10.0 6.3 12.5 10.0 17.5 14.2

700 700 711.0 711.0 700 8.0 8.0 10.0 10.0 14.2 14.2 20.0 20.0

700 600 711.0 610.0 700 8.0 5.0 10.0 10.0 14.2 12.5 20.0 16.0

800 800 813.0 813.0 800 8.0 8.0 12.5 12.5 16.0 16.0 20.0 20.0

800 700 813.0 711.0 800 8.0 8.0 12.5 10.0 16.0 14.2 20.0 20.0

900 900 914.0 914.0 900 10.0 10.0 12.5 12.5 16.0 16.0

900 800 914.0 813.0 900 10.0 8.0 12.5 12.5 16.0 16.0

1000 1000 1016.0 1016.0 1000 10.0 10.0 14.2 14.2 20.0 20.0

1000 900 1016.0 914.0 1000 10.0 10.0 14.2 12.5 20.0 16.0

1200 1200 1220.0 1220.0 1200 12.5 12.5

1200 1000 1220.0 1016 1200 12.5 12.5




7.2 Designation

Name, DN1/ DN2, s1/s2, material, standard No. Example: Tee piece, 200/ 200, 3.2/ 3.2, 1.4404, EN 10253-4




8 Reinforced branch connections – allowable pressures 8.1 General

The allowed pressures for the normal wall thicknesses for each pipe class have been calculated according to EN 13480-3. The pipes are with wall thicknesses according to different pipe classes. The branches are reinforced with plate. See standard 13.02.09.

8.2 Calculation basis Material 1.4404 Temperature t = 20 C Corrosion allowance c o = 0 mm Tolerance allowance c = 10 % however at least ± 0.2 mm for diameters 21...1220 mm

Welding factor z = 1.0

Allowable pressures are presented in MPa

8.3 Tables

Allowable pressure tables for normal walls of pipe classes:

Table 1 6H reinforced-branch connection Table 2 10H reinforced-branch connection Table 3 16H reinforced-branch connection Table 4 25H reinforced-branch connection Table 5 40H reinforced-branch connection Table 6 63H reinforced-branch connection




Table 1 Allowable pressure (MPa) for reinforced-branch connection See standard 13.01.06, item 2.2 Pipe class 6H

Outside Outside diameter of connecting pipe (mm)

diameter

main 48,3 60,3 76,1 88,9 114,3 139,7 168,3 219,1 273,0 323,9 355,6 406,4 457,0 508,0 610,0 711,0 813,0 914,0 1016,0 1220,0

pipe Wall 1,6 1,6 1,6 2,0 2,0 2,0 2,0 2,0 2,0 2,6 2,6 3,2 3,2 4,0 4,0 4,0 4,0 4,0 5,0 6,3

48,3 1,6 5,23

60,3 1,6 4,57 3,89

76,1 1,6 3,94 3,38 2,85

88,9 2,0 4,56 3,92 3,31 3,24

114,3 2,0 3,84 3,33 2,84 2,78 2,31

139,7 2,0 3,33 2,91 2,50 2,44 2,04 1,76

168,3 2,0 2,91 2,56 2,21 2,16 1,81 1,57 1,36

219,1 2,0 2,39 2,12 1,84 1,80 1,52 1,33 1,16 0,95

273,0 2,0 2,02 1,80 1,58 1,54 1,31 1,15 1,00 0,83 0,70

323,9 2,6 2,35 2,12 1,87 1,79 1,53 1,34 1,18 0,97 0,82 0,79

355,6 2,6 2,19 1,97 1,75 1,67 1,44 1,26 1,11 0,92 0,78 0,75 0,70

406,4 3,2 2,48 2,25 2,01 1,91 1,65 1,46 1,28 1,06 0,90 0,85 0,79 0,77

457,0 3,2 2,25 2,05 1,84 1,75 1,52 1,34 1,19 0,99 0,84 0,79 0,74 0,72 0,66

508,0 4,0 2,65 2,43 2,20 2,08 1,82 1,62 1,44 1,20 1,02 0,95 0,88 0,84 0,77 0,77

610,0 4,0 2,28 2,10 1,91 1,81 1,60 1,42 1,27 1,07 0,91 0,85 0,79 0,75 0,69 0,69 0,60

711,0 4,0 2,00 1,85 1,69 1,61 1,42 1,28 1,14 0,97 0,83 0,77 0,72 0,68 0,63 0,63 0,54 0,48

813,0 4,0 1,78 1,66 1,52 1,45 1,29 1,16 1,04 0,88 0,76 0,70 0,66 0,63 0,58 0,57 0,50 0,45 0,40

914,0 4,0 1,61 1,50 1,38 1,32 1,18 1,06 0,96 0,82 0,70 0,65 0,61 0,58 0,53 0,53 0,46 0,41 0,37 0,34

1016,0 5,0 1,88 1,77 1,64 1,56 1,41 1,28 1,16 0,99 0,86 0,79 0,74 0,70 0,64 0,63 0,55 0,49 0,44 0,40 0,40

1220,0 6,3 2,06 1,95 1,83 1,75 1,59 1,46 1,34 1,16 1,02 0,93 0,88 0,82 0,75 0,72 0,63 0,56 0,51 0,46 0,45 0,43




Table 2 Allowable pressure (MPa) for reinforced-branch connection See standard 13.01.06, item 2.2

Pipe class 10H


diameter

main 48,3 60,3 76,1 88,9 114,3 139,7 168,3 219,1 273,0 323,9 355,6 406,4 457,0 508,0 610,0 711,0 813,0 914,0 1016,0 1220,0

pipe Wall 1,6 1,6 1,6 2,0 2,0 2,0 2,0 2,0 2,0 2,6 2,6 3,2 3,2 4,0 5,0 5,0 6,3 8,0 8,0 10,0

48,3 1,6 5,23

60,3 1,6 4,57 3,89

76,1 1,6 3,94 3,38 2,85

88,9 2,0 4,56 3,92 3,31 3,24

114,3 2,0 3,84 3,33 2,84 2,78 2,31

139,7 2,0 3,33 2,91 2,50 2,44 2,04 1,76

168,3 2,0 2,91 2,56 2,21 2,16 1,81 1,57 1,36

219,1 2,0 2,39 2,12 1,84 1,80 1,52 1,33 1,16 0,95

273,0 2,0 2,02 1,80 1,58 1,54 1,31 1,15 1,00 0,83 0,70

323,9 2,6 2,35 2,12 1,87 1,79 1,53 1,34 1,18 0,97 0,82 0,79

355,6 2,6 2,19 1,97 1,75 1,67 1,44 1,26 1,11 0,92 0,78 0,75 0,70

406,4 3,2 2,48 2,25 2,01 1,91 1,65 1,46 1,28 1,06 0,90 0,85 0,79 0,77

457,0 3,2 2,25 2,05 1,84 1,75 1,52 1,34 1,19 0,99 0,84 0,79 0,74 0,72 0,66

508,0 4,0 2,65 2,43 2,20 2,08 1,82 1,62 1,44 1,20 1,02 0,95 0,88 0,84 0,77 0,77

610,0 5,0 2,92 2,71 2,47 2,34 2,07 1,86 1,66 1,40 1,20 1,10 1,02 0,96 0,88 0,86 0,82

711,0 5,0 2,56 2,39 2,19 2,08 1,85 1,66 1,50 1,27 1,09 1,00 0,93 0,88 0,80 0,79 0,74 0,66

813,0 6,3 2,95 2,77 2,56 2,44 2,19 1,99 1,80 1,54 1,34 1,22 1,14 1,06 0,97 0,94 0,86 0,77 0,76

914,0 8,0 3,46 3,27 3,05 2,92 2,65 2,42 2,21 1,91 1,67 1,52 1,42 1,32 1,21 1,15 1,05 0,93 0,89 0,89

1016,0 8,0 3,15 2,99 2,79 2,67 2,43 2,23 2,04 1,77 1,56 1,42 1,33 1,23 1,13 1,08 0,98 0,87 0,84 0,84 0,77

1220,0 10,0 3,40 3,25 3,07 2,95 2,72 2,52 2,33 2,05 1,81 1,66 1,56 1,45 1,34 1,27 1,14 1,02 0,96 0,94 0,86 0,82





Pipe class 16H


diameter

main 26,9 33,7 42,4 48,3 60,3 76,1 88,9 114,3 139,7 168,3 219,1 273,0 323,9 355,6 406,4 457,0 508,0 610,0 711,0 813,0

pipe Wall 1,6 1,6 1,6 1,6 2,0 2,0 2,0 2,0 2,0 2,6 3,2 3,2 4,0 5,0 6,3 8,0 8,0 10,0 10,0 12,5

26,9 1,6 6,21

33,7 1,6 5,75 5,23

42,4 1,6 5,01 4,57 3,89

48,3 1,6 4,29 3,94 3,38 2,85

60,3 2,0 4,95 4,56 3,92 3,31 3,24

76,1 2,0 4,15 3,84 3,33 2,84 2,78 2,31

88,9 2,0 3,59 3,33 2,91 2,50 2,44 2,04 1,76

114,3 2,0 3,13 2,91 2,56 2,21 2,16 1,81 1,57 1,36

139,7 2,0 2,55 2,39 2,12 1,84 1,80 1,52 1,33 1,16 0,95

168,3 2,6 2,86 2,69 2,41 2,11 2,02 1,72 1,50 1,32 1,08 1,01

219,1 3,2 3,14 2,97 2,68 2,37 2,25 1,93 1,69 1,49 1,22 1,11 1,06

273,0 3,2 2,91 2,76 2,49 2,22 2,11 1,81 1,59 1,40 1,16 1,05 1,00 0,93

323,9 4,0 3,34 3,18 2,91 2,60 2,46 2,14 1,89 1,67 1,38 1,24 1,15 1,07 1,05

355,6 5,0 3,89 3,72 3,42 3,10 2,92 2,56 2,28 2,02 1,69 1,49 1,37 1,27 1,22 1,22

406,4 6,3 4,59 4,42 4,10 3,74 3,53 3,12 2,80 2,50 2,10 1,84 1,67 1,56 1,47 1,43 1,45

457,0 8,0 5,10 4,93 4,62 4,27 4,05 3,62 3,28 2,96 2,52 2,21 2,00 1,87 1,74 1,67 1,64 1,56

508,0 8,0 4,46 4,32 4,06 3,76 3,58 3,22 2,93 2,65 2,27 2,00 1,82 1,70 1,59 1,52 1,49 1,42 1,26

610,0 10,0 5,04 4,91 4,65 4,34 4,15 3,77 3,46 3,16 2,74 2,42 2,20 2,06 1,92 1,81 1,75 1,63 1,45 1,43

711,0 10,0 4,54 4,42 4,20 3,94 3,77 3,44 3,16 2,90 2,52 2,24 2,03 1,91 1,78 1,69 1,63 1,52 1,35 1,33 1,22

813,0 12,5 5,24 5,12 4,89 4,62 4,44 4,09 3,79 3,50 3,08 2,75 2,50 2,36 2,19 2,06 1,97 1,81 1,62 1,56 1,42 1,43





Pipe class 25H


diameter

main 10,2 17,2 21,3 26,9 33,7 42,4 48,3 60,3 76,1 88,9 114,3 139,7 168,3 219,1 273,0 323,9 355,6 406,4 457,0

pipe Wall 1,6 1,6 1,6 1,6 1,6 2,0 2,0 2,0 2,6 3,2 4,0 5,0 5,0 6,3 8,0 10,0 12,5 12,5 12,5

10,2 1,6 8,41

17,2 1,6 7,33 6,21

21,3 1,6 6,74 5,75 5,23

26,9 1,6 5,82 5,01 4,57 3,89

33,7 1,6 4,94 4,29 3,94 3,38 2,85

42,4 2,0 5,67 4,95 4,56 3,92 3,31 3,24

48,3 2,0 4,72 4,15 3,84 3,33 2,84 2,78 2,31

60,3 2,0 4,05 3,59 3,33 2,91 2,50 2,44 2,04 1,76

76,1 2,6 4,63 4,15 3,87 3,41 2,95 2,82 2,36 2,04 1,95

88,9 3,2 4,72 4,27 4,02 3,58 3,13 2,96 2,51 2,17 2,03 1,81

114,3 4,0 5,04 4,62 4,37 3,94 3,49 3,28 2,80 2,45 2,26 1,97 1,81

139,7 5,0 5,59 5,18 4,93 4,49 4,01 3,77 3,26 2,87 2,61 2,25 2,04 1,95

168,3 5,0 5,16 4,79 4,57 4,17 3,74 3,52 3,05 2,69 2,46 2,13 1,92 1,84 1,72

219,1 6,3 5,94 5,56 5,33 4,91 4,45 4,19 3,67 3,26 2,97 2,55 2,27 2,13 1,98 1,96

273,0 8,0 6,96 6,56 6,32 5,88 5,38 5,07 4,49 4,03 3,66 3,15 2,78 2,57 2,39 2,31 2,31

323,9 10,0 8,07 7,66 7,41 6,94 6,41 6,07 5,43 4,91 4,47 3,86 3,40 3,10 2,90 2,75 2,69 2,71

355,6 12,5 8,69 8,32 8,09 7,65 7,13 6,79 6,15 5,62 5,16 4,49 3,97 3,61 3,39 3,18 3,06 3,01 2,86

406,4 12,5 7,55 7,25 7,06 6,70 6,27 5,99 5,45 5,01 4,61 4,04 3,59 3,28 3,08 2,89 2,79 2,74 2,60 2,32

457,0 12,5 6,67 6,42 6,26 5,96 5,60 5,36 4,90 4,51 4,17 3,67 3,28 3,00 2,82 2,66 2,56 2,52 2,39 2,14 1,94





Pipe class 40H


diameter

main 10,2 17,2 21,3 26,9 33,7 42,4 48,3 60,3 76,1 88,9 114,3 139,7 168,3 219,1 273,0

pipe Wall 1,6 1,6 1,6 1,6 1,6 1,6 1,6 1,6 1,6 2,0 2,6 3,2 4,0 5,0 6,3

10,2 1,6 40,23

17,2 1,6 28,53 20,28

21,3 1,6 24,36 17,83 15,34

26,9 1,6 20,31 15,30 13,33 11,31

33,7 1,6 16,91 13,07 11,51 9,87 8,41

42,4 1,6 13,95 11,04 9,81 8,51 7,33 6,21

48,3 1,6 12,47 9,99 8,93 7,79 6,74 5,75 5,23

60,3 1,6 10,28 8,39 7,56 6,66 5,82 5,01 4,57 3,89

76,1 1,6 8,35 6,95 6,31 5,61 4,94 4,29 3,94 3,38 2,85

88,9 2,0 9,26 7,82 7,15 6,40 5,67 4,95 4,56 3,92 3,31 3,24

114,3 2,6 9,59 8,29 7,67 6,95 6,23 5,50 5,10 4,43 3,77 3,60 3,29

139,7 3,2 9,87 8,69 8,11 7,42 6,73 6,00 5,59 4,90 4,22 3,97 3,56 3,32

168,3 4,0 10,46 9,36 8,81 8,15 7,47 6,74 6,31 5,60 4,86 4,54 4,02 3,68 3,49

219,1 5,0 10,29 9,39 8,93 8,36 7,76 7,09 6,70 6,02 5,31 4,95 4,37 3,96 3,69 3,30

273,0 6,3 10,61 9,83 9,42 8,91 8,36 7,74 7,37 6,70 5,99 5,59 4,94 4,47 4,11 3,62 3,35





Pipe class 63H


diameter

main 10,2 17,2 21,3 26,9 33,7 42,4 48,3 60,3 76,1 88,9 114,3 139,7 168,3

pipe Wall 1,6 1,6 1,6 1,6 1,6 1,6 1,6 2,0 2,6 3,2 4,0 5,0 6,3

10,2 1,6 40,23

17,2 1,6 28,53 20,28

21,3 1,6 24,36 17,83 15,34

26,9 1,6 20,31 15,30 13,33 11,31

33,7 1,6 16,91 13,07 11,51 9,87 8,41

42,4 1,6 13,95 11,04 9,81 8,51 7,33 6,21

48,3 1,6 12,47 9,99 8,93 7,79 6,74 5,75 5,23

60,3 2,0 13,07 10,71 9,66 8,51 7,43 6,38 5,83 5,44

76,1 2,6 13,84 11,63 10,61 9,47 8,36 7,26 6,66 6,08 5,65

88,9 3,2 14,90 12,75 11,73 10,56 9,41 8,25 7,60 6,88 6,27 6,06

114,3 4,0 14,95 13,10 12,20 11,14 10,06 8,95 8,31 7,50 6,78 6,44 5,84

139,7 5,0 15,68 14,01 13,17 12,16 11,12 10,01 9,37 8,47 7,62 7,17 6,40 6,01

168,3 6,3 16,76 15,24 14,45 13,49 12,47 11,36 10,71 9,74 8,76 8,20 7,26 6,70 6,38

8.2 Designation

Name, Reinforced branch connection, Do1/ Do2, s1/ s2, material, standard No.

Example: Reinforced branch connection, 168.3/114.3, 5.0/4.0, 1.4404, 13.02.08




9 Reinforced branch connection with plate 9.1 Dimensions

DN1 lpl

40 50 (65) 80

15 15 15 15

100 (125) 150 200

15 16 17 20

250 300 350 400

22 27 29 31

(450) 500 600

700

800

900

1000

1200

36 43

47

50

54

57

67

83

The wall thickness of the reinforcing plate must be minimum the wall thickness of the main pipe (s).




9.2 Designation

Name DN 1/ DN 2, material, standard No.

Example: Reinforced - branch connection, 200/ 25, 1.4404, 13.02.09




10 Blank flange 0H...25H

10.1 Dimensions

2 1 Plate Ø D1, s = 2 1.4404

1 1 Blank flange EN 1092-1

PN 10… PN 25

Type 05

P265GH

Hot dip galvanized

Part Pcs Description Dimension Material

Note: PN 10 shall be used for pipe classes OH…10H.

D1 is equal to flange facing diameter.

10.2 Designation

Name, DN, pressure class of pipe class, material of the flange, material of lining plate, standard No.

Example: Blank flange, DN 250, PN 16, P265GH, 1.4404, 13.02.11




11 Spade blank

11.1 General

Spade blank according to this standard shall be used between flanges instead of shut valve.

If the plate thickness s1 < 8 mm, the plate material is 1.4404.

When s1 > 8 mm, the material is P265GH, which has been lined with 1.4404.




DN

D

Plate thickness (mm) s

L B

Pressure difference, MPa

mm 0.1 MPa 0.25 MPa 0.4 MPa 0.6 MPa 1.0 MPa mm mm

15 47

1.6 1.6

20

20 58 1.6

25 68 1.6

2

(32) 78 1.6 2

75

40 88

50 102

2 3 3

30

(65) 122 2

4

80 133 3

3 4 5

100 158

4 5 6

(125) 184 2 4

5 6

150 212 4

8

200 268 5 6 8 9+3=12 100

250 320 6 8 9+3=12 11+3=14

300 370 8

8 10+3=13 12+3=15 50

350 430 5 9+3=12 12+3=15 15+3=18

400 482 6 8 11+3=14 13+3=16 17+3=20

500 585 8 10+3=13 13+3=16 16+3=19 20+3=23 150

600 685 8 12+3=15 15+3=18 19+3=22 24+3=27 75

800 905 10+3=13 15+3=18 19+3=22 23+3=26 29+3=32 85

Notes: 1. Carbon steel surface must be painted according to painting instructions. 2. One hole in handle for closed plate (two for open plate).

11.2 Designation

Name, DN, pressure difference, standard No.

Example: Spade blank, 150, 0.6, 13.02.12




12 Open spade

12.1 General

Open spade according to this standard shall be used between flanges when blind disc according to standard 02-009 has been removed.

12.2 Dimensions

Dimensions are in Table 1.




Table 1

Plate thickness (mm) s

L B

Pressure difference, MPa

DN D1

mm

D

mm

0.1 MPa 0.25 MPa 0.4 MPa 0.6 MPa 1.0 MPa mm mm

15 21 47 1.6

1.6 1.6

20

20 27 58 1.6

25 34 68 2

2

(32) 42 78 1.6

75

40 48 88 2

50 60 102

3 3

30

(65) 76 122 2

4

80 89 133

3 4 5

100 114 158 2

3 4 5 6

(125) 140 184 4 5 8

150 168 212

6

200 219 268 4 5 6 8 9+3=12 100

250 273 320 6 8 9+3=12 11+3=14

300 324 370 5 8 8 10+3=13 12+3=15 50

350 356 430 9+3=12 12+3=15 15+3=18

400 406 482 6 8 11+3=14 13+3=16 17+3=20

500 508 585 8 10+3=13 13+3=16 16+3=19 20+3=23 150

600 610 685 8 12+3=15 15+3=18 19+3=22 24+3=27 75

12.3 Material

When s1 < 8 mm, material is 1.4404, and when s1 > 8 mm, material is P265GH, or equal with 1.4404 lining.

Notes: 1. Carbon steel surface must be painted according to painting instructions.

2. Two holes in handle indicates open spade (one for spade blank)

12.4 Designation Name, DN, pressure difference, standard No. Example: Open spade, 250, 0.25, 13.02.13




13 Plate valve

13.1 General

Plate valve shall be used between flanges instead of shut valve.

13.2 Dimensions

DN 0H2...10H2

A mm

B mm

C mm

D mm

E mm

R mm

S mm

MPa

50 56 102 102 125 18 15 5 1.0 (65) 72 122 70 145 18 15 5 1.0 80 85 133 80 160 18 15 5 1.0 100 110 158 90 180 18 15 5 0.6 (125) 135 184 90 210 18 15 6 0.7 150 164 212 90 240 23 15 8 1.0 200 214 268 90 295 23 15 8 0.6 250 263 320 140 350 23 15 10 0.6 300 320 370 140 400 23 15 10 0.6 350 350 430 140 460 23 15 16 1.0 400 400 482 140 515 27 15 16 0.6 500 500 585 150 620 27 15 16 0.6 600 602 685 150 725 30 15 16 0.4

MPa indicates the maximum pressure difference over the plate. 13.4 Material

1.4404 according to EN 10028-7




13.5 Designation Name, DN, standard No. Example: Plate valve, DN 250, 13.02.14




14 Drain and spooling connection DN 40 and DN 50

14.1 Dimensions

DN 50

6 2 Flat bar Thickness 4.0 mm 1.4404

5 1 Pipe 60.3 x 1.6 13.02.03

4 1 Reinforcement ring Thickness 2.0 mm 1.4404

3 1 Bend 60 60.3 x 2.0 13.02.05

2 1 Hose coupling R 2” external thread ALSi1Mg

1 1 Valve DN 50 TH/ WE see valve spec.

Part Pcs Description Standard No. Material

DN 40

6 2 Flat bar Thickness 4.0 mm 1.4404

5 1 Pipe 48.3 x 1.6 13.02.03

4 1 Reinforcement ring Thickness 4.0 mm 1.4404

3 1 Bend 60 48.3 x 2.0 13.02.05

2 1 Hose coupling R 1 1/4“ external thread ALSi1Mg

1 1 Valve DN 40 TH/ WE see valve spec.





14.2 Designation

Name, DN, type, material, standard No.

Example: Drain connection, DN 50, A, 1.4404, 13.02.15




15 Vent connection DN 25

15.1 Dimensions

4 2 Flat bar 4.0 mm 1.4404

3 1 Hex head plug DN 25 EN 10241 1.4404 or equal

2 1 Valve DN 25, TH/ WE see valve specification

1 1 Pipe 33.7 x 1.6 EN 10217-7 1.4404


15.2 Designation

Name, DN, type, material, standard No.

Example: Vent connection, DN 25, A, 1.4404, 13.02.16




16 Sample taking connection DN 40 16.1 Dimensions

DN 40

6 1 Reinforcement plate 2) 1.4404

5 2 Flat bar 30 x 2 1.4404

4 1 Hose coupling R 1 1/2” int. thread AlSi1Mg 3)

3 1 Elbow 90° 48.3 x 2.0 13.02.05 1)

2 1 Valve DN 40 WE see valve spec.

1 1 Screwed end R 1 1/2” EN 10241 1.4404


Note: 1. Material and pipe parts according to each pipe class. 2. Thickness of the reinforcement ring = the wall thickness of the main pipe, min. 2 mm 3. Material 1.4404 in chemical lines.

16.2 Designation Name, material, standard No. Example: Sample taking connection, DN 40, 1.4404, 13.02.17

Date post:	16-Oct-2021
Category:	Documents
Upload:	others
View:	14 times
Download:	4 times

13.02 Stainless Steel Piping

Documents