1305-R08050026-AA Page 1 of 7 1-800-59-ROUSH

2005-06 Mustang Billet Aluminum Pedal Cover Kit P/N R08050020 (Manual) and R08050021 (Automatic)

Installation Instructions

1305-R08050026-AA Page 2 of 7 1-800-59-ROUSH

Before installing this Roush Performance Product, read through the entire Installation procedure and check to make sure all the items are present. Packaging List for Pedal Cover Kit #R08050020 (Manual) Item Part # Qty Accelerator pedal cover R08050022 1 Brake/clutch pedal cover SM91-5303-BC 2 Hardware kit R08050024 1 Self-tapping screw, #6 x 1/2” 4 Flathead machine screw, #8-32 x 5/8” 6 Lock nut, #8-32 6 Installation Instructions R08050026 1 Packaging List for Pedal Cover Kit #R08050021 (Automatic) Item Part # Qty Accelerator pedal cover R08050022 1 Brake pedal cover SM91-5303-AB 1 Hardware kit R08050025 1 Self-tapping screw, #6 x 1/2” 4 Flathead machine screw, #8-32 x 1/2” 4 Lock nut, #8-32 4 Installation Instructions R08050026 1 Equipment Required Drill motor Center punch 1/16” drill bit 1/8” drill bit 3/16” drill bit Scribe Phillips head screwdriver 3/32” Allen wrench 11/32” wrench Small file

1305-R08050026-AA Page 3 of 7 1-800-59-ROUSH

LIMIT OF LIABILITY STATEMENT The information contained in this publication was accurate and in effect at the time the publication was approved for printing and is subject to change without notice or liability. Roush Performance Products (RPP) reserves the right to revise the information presented herein or to discontinue the production of parts described at any time. STOP! READ IMPORTANT SAFETY PRECAUTIONS AND WARNINGS BEFORE PROCEEDING. IMPORTANT SAFETY NOTICE Appropriate disassembly, assembly methods and procedures are essential to ensure the personal safety of the individual performing the kit installation. Improper installation due to the failure to correctly follow these instructions could cause personal injury or death. Read each step of the installation instructions carefully before starting the actual installation. • Always wear safety glasses for eye protection. • Place the ignition switch in the OFF position. • Always apply the parking brake when working on the vehicle. • Block the front and rear tire surfaces to prevent unexpected vehicle movement. • Operate the engine only in well-ventilated areas to avoid exposure to carbon monoxide. • Do not smoke or use flammable items near or around the fuel system. • Use chemicals and cleaners only in well-ventilated areas. • Batteries can produce explosive hydrogen gas, which can cause personal injury. Therefore do not allow flames, sparks or flammable substances to come near the battery. • Keep hands and any other objects away from the radiator fan blades. • Keep yourself and your clothing away from moving parts when the engine is running. • Do not wear loose clothing or jewelry that can be caught in rotating or moving parts.

1305-R08050026-AA Page 4 of 7 1-800-59-ROUSH

Brake and Clutch Cover Installation (Manual)

Remove the rubber pedal pads from the brake and clutch pedals.

Place the Roush clutch pedal cover centered over top of the metal pedal surface. Scribe the location of the (3)

attaching holes. Center punch the hole locations. Using the 1/8” drill bit, drill a pilot hole in each of the (3)

locations. Repeat this procedure for the brake pedal. Drill the attaching holes to finished size using the 3/16” drill

bit. Deburr any sharp edges with either a larger drill bit or a file.

Attach the Roush pedal covers using (6) black flat head machine screws and (6) lock nuts for each cover. Torque nuts to 40 in-lbs.

1305-R08050026-AA Page 5 of 7 1-800-59-ROUSH

Brake Cover Installation (Automatic)

Remove the factory rubber pedal pad from the brake pedal.

Align the Roush pedal cover with the right edge of the pedal cover flush with the right side of the metal pedal surface. Scribe the location of the (4) attaching holes.

Center punch the hole locations. Using the 1/8” drill bit, drill a pilot hole in each of the (4) locations. Drill the

attaching holes to finished size using the 3/16” drill bit. Deburr any sharp edges with either a larger drill bit or a

file.

Attach the Roush pedal cover using the (4) flat head machine screws and (4) lock nuts. Torque nuts to 40 in-lbs.

1305-R08050026-AA Page 6 of 7 1-800-59-ROUSH

Accelerator Cover Installation

Locate the Roush pedal cover centered over the accelerator pedal and scribe the location of the (4) attaching holes. Using the 1/16” drill bit, drill a pilot hole in each of the (4) locations.

Use the (4) self-tapping screws to secure the cover onto the accelerator pedal. Because these are self-tapping fasteners, use caution not to overtighten.

After installation is complete, double-check that all nuts and screws are installed securely. If you are missing any items or have any questions regarding the installation, please call us toll free at 1-800-59-ROUSH.

1305-R08050026-AA Page 7 of 7 1-800-59-ROUSH

Warranty All retail parts carry a 90-day warranty from the date of purchase. This warranty covers defects in materials or workmanship, and does not include (I) normal wear and tear, environmental conditions, improper installation; (II) road hazards, misuse, abuse, neglect, accidents, collision, fire, theft, freezing, vandalism, riot, explosion, or objects striking the vehicle; (III) misusing the vehicle, such as driving over curbs, overloading, racing, or using the vehicle as a stationary power source; (iv) altering, disassembling or modifying the parts; (v) defects caused or induced by failures, breakdowns, or damage by other parts, components or the vehicle; (vi) subjecting the parts to excessive moisture or water or any motor vehicle fluids (e.g.: oil, anti-freeze, battery acid, brake fluid, etc.); (vii) acts of God, natural disasters and other similar causes beyond the reasonable control of Roush; or (viii) application of chemicals that affect the parts. This Limited Warranty does not cover surface deterioration of paint, trim, and appearance items that result from use and/or exposure to the elements, such as stone chips, scratches, bird droppings, lightning, hail, windstorm, dings, dents, earthquake, road salt, tree sap, water or flood. ROUSH SHALL NOT BE LIABLE TO REIMBURSE CUSTOMER/DEALER FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM THE INSTALLATION OR USE OF ANY PRODUCT SOLD THROUGH THIS CATALOG OR ARISING OUT OF ANY BREACH OF WARRANTY. EXCEPT AS MAY BE STATED IN THIS CATALOG, ROUSH DISCLAIMS ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL ROUSH’S LIABILITY EXCEED THE PRICE PAID BY CUSTOMER/DEALER FOR PRODUCTS SOLD REGARDLESS IF ROUSH HAS BEEN ADVISED IN ADVANCE OF ANY POTENTIAL PROBLEM OR IF A CLAIM IS BASED ON CONTRACT, TORT, STRICT LIABILITY, PRODUCT LIABILITY OR OTHERWISE. SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF IMPLIED WARRANTIES OR THEIR DURATION, OR LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE EXCLUSIONS OR LIMITATIONS MAY NOT APPLY.