BB BARREL BOLTC.O.S CHECK ON SITEIBW INSTANT BOILING WATER UNIT BY OTHERSLKC LOCK (CABINET/ DRAWER)PTD PAPER TOWEL DISPENSERMX MIXERS SINKSD SOAP DISPENSERST STONETM TIMBERLAM LAMNOM. NOMINALUNO UNLESS NOTED OTHERWISE
ABBREVIATED NOTES
JOINERY NOTES1. ALL DIMENSIONS ARE TO BE CHECKED ON SITE PRIOR TO CONSTRUCTION.2. THIS SECTION OF WORK SHALL BE READ IN CONJUNCTION WITH JOINERYFINISHES; WALL FINISHES; FIXTURES & FITTINGS SCHEDULES.
DESIGN NOTES- LABORATORY/ KITCHENETTE UNITSTYPICAL1. JOINERY / CABINET DOOR HANDLES - REFER TO JOINERY SCHEDULE.2. SINK/ TAPWARE/ SOAP & PAPER TOWEL DISPENSERS SHOWNINDICATIVELY. REFER TO FIXTURES AND FINISHES SCHEDULES.3. OVERHEAD CUPBOARDS TO HAVE A FIXED MID SHELF, WHITE MELAMINEFINISH UNO.4. LOWER CUPBOARDS TO HAVE ONE ADJUSTABLE SHELF, WHITE MELAMINEFINISH UNO.5. BENCHTOPS TO BE SOLID COMPACT LAMINATE, NOM. 18mm THICK.REFER SCHEDULE FOR COLOUR.6. TOP DRAWER FITTED WITH CUTLERY INSERT TO SUIT DRAWER WIDTH -KITCHENETTE ONLY7. CUPBOARDS TO HAVE HAFELE HINGES 90/170 DEGREE OPENING, ALLMETAL SPRUNG FULLY CONCEALED HINGES TO SUIT DOOR WEIGHT ANDCONFIGURATION.8. DRAWERS FITTED WITH HAFELE FULLY EXTENDABLE HEAVY DUTY SELFCLOSING RUNNERS, LENGTH TO SUIT CARCASS.9. LOCKABLE DRAWERS FITTED WITH HAFELE SYMO 3000 LOCKING SYSTEM TOSUIT DRAWER CONFIGURATION AS NOMINATED. KEY TO BE JOINERY MASTERKEY SYSTEM DISTINCT TO LOCK SYSTEM, UNO.10. KEY DRAWERS AND ADJACENT CABINET WITHIN THE SAME AREA ALIKE,AND ALL OTHER INDIVIDUAL COUNTER TO BE KEYED TO DIFFER. CONFIRMWITH CLIENT FOR LOCK/ KEY REQUIREMENTS.11. PROVIDE 3M BRAND RUBBER BUFFERS BETWEEN ALL CLOSINGSURFACES. ADHESIVE APPLIED.12. KICKBOARDS TO BE 50mm RECESSED FROM FINISHED FACE OFCUPBOARDS.13. CABINET DOORS/DRAWERS TO BE 20mm RECESSED FROM BENCHTOPFINISHED EDGE.14. SILICONE SEAL JUNCTION OF SPLASHBACK TO BENCH TOP, ANDSPLASHBACK TO WALL WITH APPROVED SEALANT .15. ALL SELECTED LAMINATES TO BE ON LAMINEX EO BOARD/ SUBSTRATES(OR EQUAL APPROVED) TO SUIT JOINERY LOCATION & APPLICATION.16. CUPBOARD DOORS AND DRAWER FRONTS TO HAVE ABS MATCHING EDGESTRIPS.
2066
1200
900
2100
EQEQ
EQEQ
350
E.Q528
E.Q528
E.Q528 TYPICAL 450
16
E.Q509 E.Q
509E.Q
509E.Q
509
16
16
2066
ONE LOCKABLE CUPBOARDAND ONE LOCKABLE DRAWERAS SHOWN
SPLASHBACK - COMPACT LAMINATE
BENCHTOP - COMPACT LAMINATE
GABLE SPACER TO EITHER SIDEOF END WALL ( WALLS NOTDRAWN FOR CLARITY) -TYPICAL
600
600
750
150
600
PTD
SD
S
MX
GABLE SPACER TO EITHER SIDEOF END WALL ( WALLS NOTDRAWN FOR CLARITY) -TYPICAL
IBW
900
600
600
2695
EXISTING BLOCK WALL
EXISTING COLUMN
GABLE SPACERTO END WALL (WALL NOTDRAWN FOR CLARITY)EXPOSED EDGE TO MATCHADJACENT FINISH ASSPECIFIED
END WALL NOT DRAWNFOR CLARITY
MX
IBW
PTD
SD
SCRIBE BENCH TOP ANDNEATLY AROUND COLUMN,SILICONE SEAL AT JUNCTIONWITH APPROVED SEALANT
NO LOCKS
EQ.
EQ.
EQ.
EQ.
EQ.
EQ2.
EQ2.
EQ2.CONFIRM ON SITE
1448
TILED SPLASHBACK
OVERHANG 50
900
500
OVERHANG 20
NOM.1364 COVED VINYL SKIRTING WITH 20mmPREFORMED COVE FILLET TOKICKBOARD
GABLE SPACER TO END WALL(WALL NOTDRAWN FOR CLARITY)EXPOSED EDGE TO MATCH ADJACENT FINISHAS SPECIFIED
CORNER CUPBOARD WITH PIANOHINGES
GABLE SPACER TO ENDWALL, EXPOSED EDGESTO MATCH ADJACENTFINISH
The location of existing walls and structure have been provided to AGArchitects by others.As such AG Architects cannot warrant or verify the accuracy of existinglayout and takes no responsibility for discrepancies in measurementsassociated with setout of new work joining into existing elements.Where setout dimensions of new work are critical in order to join intoexisting it is the responsibility of the builder to check and confirm location& nature of all existing elements prior to setting out; fabrication; andconstruction of new works.All discrepancies between site conditions & those shown on drawings areto be referred to the architect for further instructions.
As indicated (@ A1)
16/1
2/20
13 6
:29:
39 P
M
1
JOINERY DETAILS -LABS & KITCHENETTES
Issue Date
LA
1039-A-WD-84.10
CDPOM JACKSON'S INTERNATIONAL
AIRPORT ITB UPGRADEPORT MORESBY PNG
Issue Description Date By1 PRELIMINARY ISSUE FOR CLIENT FEEDBACK 13/12/13 NAS
SHUTTER & ASSOCIATEDACCESSORIES NOT SHOWN,REFER TO NOTES ON ELEVATIONS
550
350
STONE COUNTERTOP& SIDE GABLES.MITRED EDGES.
50
KWILA LEDGE
FINISH DADO ATFACE OF COUNTER-TOP SIDE GABLE TYPICAL
KWILA BOTTOM RAIL
RECESSEDKICKBOARD
JOINERY NOTES1. ALL DIMENSIONS ARE TO BE CHECKED ON SITE PRIOR TO CONSTRUCTION.2. THIS SECTION OF WORK SHALL BE READ IN CONJUNCTION WITH FIXTURES &FINISHES SCHEDULES
DESIGN NOTES- SERVICE/ RECEPTION COUNTERSTYPICAL1. JOINERY / CABINET DOOR HANDLES - REFER TO JOINERY SCHEDULE.2. PROVIDE ONE ADJUSTABLE SHELF TO EACH CUPBOARD, WHITE MELAMINEFINISH UNO.3. CUPBOARDS TO HAVE HAFELE HINGES 90/170 DEGREE OPENING, ALLMETAL SPRUNG FULLY CONCEALED HINGES TO SUIT DOOR WEIGHT ANDCONFIGURATION.4. TOP DRAWER FITTED WITH A PENCIL TRAY INSERT.5. DRAWERS FITTED WITH HAFELE FULLY EXTENDABLE HEAVY DUTY SELFCLOSING RUNNERS, LENGTH TO SUIT CARCASS.6. DRAWERS WITH GANG LOCK, HAFELE SYMO 3000 LOCKING SYSTEM TOSUIT DRAWER CONFIGURATION AS NOMINATED. KEY TO BE JOINERY MASTERKEY SYSTEM DISTINCT TO LOCK SYSTEM, UNO7. KEY DRAWERS AND ADJACENT CABINETS WITHIN THE SAME AREA ALIKE,AND ALL OTHER INDIVIDUAL COUNTERS TO BE KEYED TO DIFFER. CONFIRMWITH CLIENT LOCK/ KEY REQUIREMENTS.8. CABINETS FITTED WITH LAMINATE 3M BRAND RUBBER BUFFERS BETWEENALL CLOSING SURFACES. ADHESIVE APPLIED.9. CABINET DOOR/ DRAWERS TO BE RECESSED 20mm FROM THE BENCH TOPFINISHED EDGE.10. PROVIDE GABLE SPACERS TO CABINETS AT JUNCTION WITH WALLS. ALLEXPOSED EDGES FINISHED TO MATCH ADJACENT SURFACE.11. SILCONE SEAL JUNCTION OF BENCH TOP TO WALL WITH APPROVEDSEALANT12. ALL SELECTED LAMINATES TO BE ON LAMINEX EO BOARD/ SUBSTRATES(OR EQUAL APPROVED) TO SUIT JOINERY LOCATION & APPLICATION
RECESSED KICKBOARD
RETURN SKIRTING TOFACE OF KICKBOARD.
RETURN SKIRTINGTO FACE OF KICKBOARD
FACE OF KICKBOARDSETBACK 50mm FROMFACE OF WALL RETURN.
FINISH DADO ATFACE OF COUNTER-TOP RETURN
KWILA LEDGE
KWILA BOTTOM RAIL
SHUTTER & ASSOCIATEDACCESSORIES NOT SHOWN,REFER TO NOTES ON ELEVATIONS
84.11
1746 550 350
1904
1004
201
1757
50
50
VISA O.A.NEW
FOREXNEW
KWILA
LEDG
EKW
ILA LE
DGE
84.11
- FIT COUNTERS NEATLYBETWEEN WALLS- BENCHTOPS FIXED TOSUPPORTS FIXED TO FACEOF WALLS
CUT BENCHTOPNEATLY AROUNDCOLUMN BUILDOUT
3 2
ALLOW TO PROVIDE TWO GROMMETHOLES TO EACH COUNTER BENCHTOPWITH ADJUSTABLE COVERS, NOM.80mm DIAMETER, 40mm CLEAR OFALL EDGES. COLOUR TO MATCHBENCHTOP. CONFIRM EXACT LOCATIONWITH CLIENT.
350 550
150 300BENCHTOP
600
BENC
HTOP
& LE
DGE
750
300
COUN
TERT
OP11
00
10 100
BENCHTOP -LAMINATE FINISH
STONE COUNTERTOP
STONE PANEL FACINGKWILA LEDGE SUPPORTEDON ANGLES FIXED TOSUB-STRUCTURESTONE PANEL FACING
The location of existing walls and structure have been provided to AGArchitects by others.As such AG Architects cannot warrant or verify the accuracy of existinglayout and takes no responsibility for discrepancies in measurementsassociated with setout of new work joining into existing elements.Where setout dimensions of new work are critical in order to join intoexisting it is the responsibility of the builder to check and confirm location& nature of all existing elements prior to setting out; fabrication; andconstruction of new works.All discrepancies between site conditions & those shown on drawings areto be referred to the architect for further instructions.
As indicated (@ A1)
16/1
2/20
13 6
:29:
40 P
M
1
JOINERY DETAILS - VISAOA & FOREX
Issue Date
LA
1039-A-WD-84.11
CDPOM JACKSON'S INTERNATIONAL
AIRPORT ITB UPGRADEPORT MORESBY PNG
SCALE: (@ A1)5 LGB- FOREX COUNTER
Issue Description Date By1 PRELIMINARY ISSUE FOR CLIENT FEEDBACK 13/12/13 NAS
SCALE: (@ A1)6 LGB- VISA O.A. COUNTER
SCALE: 1 : 20 (@ A1)1 LGB- VISA OA_FOREX
SCALE: 1 : 20 (@ A1)4 TYPICAL COUNTER SECTION
SCALE: 1 : 20 (@ A1)2 LGB- VISA OA & FOREX
SCALE: 1 : 20 (@ A1)3 LGB- VISA OA & FOREX 2
STONE COUNTERTOP & GABLE ENDS
WORK TOP IN SINGLE PIECE - CLAM5
PROVIDE UNDER BENCH CABLE MANAGEMENT TRAY TOSUIT
ALLOW TWO GROMMET HOLES (TOTAL) WITH ADJUSTABLE COVERS,NOM. 80mm DIA. COLOUR TO MATCH, POSITION TO EITHER SIDE OFPIGEON HOLE UNITS
LOCKABLE UNDER BENCH DRAWERS IN LAMINATEFINISH AS SPECIFIED
STAINLESS STEEL LEG WITH ADJUSTABLE FOOT
RECESSED KICKBOARD - CLAM5
KWILA BOTTOM RAIL
FIT A4 (LANDSCAPE) UNDER BENCH PIGEON HOLE UNITJF2 FINISH.
S3
S3CLAM5
800
4096
015
0
NOM.
4300
1150
LOCK
FIT CABINET NEATLY AROUNDCOLUMN ( SHOW DASHED LINE) AND END WALL ( NOT DRAWN FOR CLARITY)
DRAWER FRONTS - JF5
GABLE SPACER, FINISH TOMATCH ADJACENT FINISH
HAFELE SYMO 3000JOINERY LOCK WITHBARREL BOLT AS SHOWN
CUPBOARDS FITTED WITH 2 (TWO) ADJUSTABLESHELVES, FINISH IN WHITE MELAMINEINTERNALLY, POSITION OF BRASS FERRULES TOSUIT A4 LEVER ARCH FOLDER HEIGHT
LKC
LKC
LKC
LKC
GANG LOCK DRAWERS
STONECOUNTERTOP- S3
JF2
CLAM5KICKBOARD
BB
BB
BB
END WALL ( NOT DRAWN FORCLARITY)
JF2
875 1700 900
3475
1300 850 1325
S3
COUNTERTOP - STONE (S3)
BENCH TOP IN SINGLE PIECELAMINATED BOTH SIDES,WITH SQUARE EDGE PROFILE
BUTT JOINT KWILA LEDGE TO LAMINATEDBENCH TOP
CLAM5
STAINLESS STEEL LEGS UNDER
KWILA LEDGE COMPLETED WITH COUNTERSUNKSUPPORT FIXING PLATES POWDER COATED IN BLACK,SECURELY FIXED TO SUB STRUCTURE
600
150
350
BB BARREL BOLTC.O.S CHECK ON SITEIBW INSTANT BOILING WATER UNIT BY OTHERSLKC LOCK (CABINET/ DRAWER)PTD PAPER TOWEL DISPENSERMX MIXERS SINKSD SOAP DISPENSERST STONETM TIMBERLAM LAMNOM. NOMINALUNO UNLESS NOTED OTHERWISE
ABBREVIATED NOTESJOINERY NOTES1. ALL DIMENSIONS ARE TO BE CHECKED ON SITE PRIOR TO CONSTRUCTION.2. THIS SECTION OF WORK SHALL BE READ IN CONJUNCTION WITH JOINERYFINISHES & FIXTURES SCHEDULES
DESIGN NOTES- SERVICE/ RECEPTION COUNTERSTYPICAL1. JOINERY / CABINET DOOR HANDLES - REFER TO JOINERY SCHEDULE.2. PROVIDE ONE ADJUSTABLE SHELF TO EACH CUPBOARD, WHITE MELAMINE FINISH UNO.3. CUPBOARDS TO HAVE HAFELE HINGES 90/170 DEGREE OPENING, ALL METAL SPRUNG FULLY CONCEALED HINGES TO SUIT DOOR WEIGHT AND CONFIGURATION.4. TOP DRAWER FITTED WITH A PENCIL TRAY INSERT.5. DRAWERS FITTED WITH HAFELE FULLY EXTENDABLE HEAVY DUTY SELF CLOSING RUNNERS, LENGTH TO SUIT CARCASS.6. DRAWERS WITH GANG LOCK, HAFELE SYMO 3000 LOCKING SYSTEM TO SUIT DRAWER CONFIGURATION AS NOMINATED. KEY TO BE JOINERY MASTER KEY SYSTEM DISTINCT TO LOCK SYSTEM, UNO7. KEY DRAWERS AND ADJACENT CABINETS WITHIN THE SAME AREA ALIKE, AND ALL OTHER INDIVIDUAL COUNTERS TO BE KEYED TO DIFFER. CONFIRM WITH CLIENT LOCK/ KEY REQUIREMENTS.8. CABINETS FITTED WITH LAMINATE 3M BRAND RUBBER BUFFERS BETWEEN ALL CLOSING SURFACES. ADHESIVE APPLIED.9. CABINET DOOR/ DRAWERS TO BE RECESSED 20mm FROM THE BENCH TOP FINISHED EDGE.10. PROVIDE GABLE SPACERS TO CABINETS AT JUNCTION WITH WALLS. ALL EXPOSED EDGES FINISHED TO MATCH ADJACENT SURFACE.11. SILCONE SEAL JUNCTION OF BENCH TOP TO WALL WITH APPROVED SEALANT12. ALL SELECTED LAMINATES TO BE ON LAMINEX EO BOARD/ SUBSTRATES (OR EQUAL APPROVED) TO SUIT JOINERY LOCATION & APPLICATION
350 500 100 10STAINLESSSTEEL LEG WITHADJUSTABLEFOOT
S3
STONE - S3
CLAM5
JF2
STONE COUNTERTOP- S3
BENCHTOP -CLAM5
350
750 KWILA BOTTOM RAIL
600 350 150
300
STAINLESS STEEL LEG WITHADJUSTABLE FOOT
STONE PANEL FACING, ARISSEDEDGES
S3S3
S3S3
S3S3
S3
S3
S3S3
OPEN UNDER
DRESSED KWILA LEDGE,FSC CERTIFIED
COUNTER TOP - STONE S3, FRONTEDGE 40mm THICK,
KICKBOARD - CLAM5
CLAM5
CLAM5
CLAM5
KWILA BOTTOM RAIL,DRESSED 38mm THICK.
OPEN UNDER
425425
425425
DESK
HEIG
HT75
0
350
Upper Ground Level www.agarchitects.net.au3/47 Anderson St [email protected] Valley Q 4006 ph. (07) 3852 1355
The location of existing walls and structure have been provided to AGArchitects by others.As such AG Architects cannot warrant or verify the accuracy of existinglayout and takes no responsibility for discrepancies in measurementsassociated with setout of new work joining into existing elements.Where setout dimensions of new work are critical in order to join intoexisting it is the responsibility of the builder to check and confirm location& nature of all existing elements prior to setting out; fabrication; andconstruction of new works.All discrepancies between site conditions & those shown on drawings areto be referred to the architect for further instructions.
As indicated (@ A1)
16/1
2/20
13 6
:29:
40 P
M
1
JOINERY DETAILS - NACINFORMATION COUNTER
OPTION AIssue Date
LA
1039-A-WD-84.12A
CDPOM JACKSON'S INTERNATIONAL
AIRPORT ITB UPGRADEPORT MORESBY PNG
SCALE: (@ A1)2 LGE- NAC INFORMATION DESK- VIEW 3- A
SCALE: (@ A1)5 LGE- NAC INFORMATION STORAGE
SCALE: (@ A1)4 LGE- NAC INFORMATION DESK- PLAN VIEW- A
SCALE: (@ A1)3 LGE- NAC INFORMATION DESK- END ELEVATION- ASCALE: (@ A1)1 LGE- NAC INFORMATION DESK- VIEW 1- A
Issue Description Date By1 PRELIMINARY ISSUE FOR CLIENT FEEDBACK 13/12/13 NAS
COUNTERTOP - STONE S3
BENCH TOP IN SINGLE PIECELAMINATED BOTH SIDE,WITH SQUARE EDGE PROFILE -COMPACT LAMINATE CLAM5
BUTT JOINT KWILA LEDGE TO COMPACTLAMINATE BENCH TOP
STAINLESS STEEL LEGS UNDER
KWILA LEDGE COMPLETED WITH COUNTERSUNKSUPPORT FIXING PLATES POWDER COATED INBLACK, SECURELY FIXED TO SUB STRUCTURE
960
600
150
350
350 3150
1235
STAINLESS STEEL LEG WITHADJUSTABLE FOOT
OPEN UNDER
KWILA LEDGE, DRESSED
COUNTERTOP - STONE S3
RECESSED KICKBOARD -CLAM5 LAMINATE
KWILA BOTTOM RAIL,DRESSED 38mm THICK
STONE PANEL FACING -S3 WITH ARISSED EDGES
520
520
520
520
520
2600
END WALLNOT DRAWNFOR CLARITY
STAINLESS STEEL LEG UNDER
FIT A4 (LANDSCAPE ) UNDER BENCHPIGEON HOLE UNIT
LOCKABLE UNDER BENCH DRAWERSIN LAMINATE FINISH
BENCHTOP -CLAM 5 COMPACT LAMINATE
JOINERY NOTES1. ALL DIMENSIONS ARE TO BE CHECKED ON SITE PRIOR TO CONSTRUCTION.2. THIS SECTION OF WORK SHALL BE READ IN CONJUNCTION WITH JOINERYFINISHES & FIXTURES SCHEDULES
DESIGN NOTES- SERVICE/ RECEPTION COUNTERSTYPICAL1. JOINERY / CABINET DOOR HANDLES - REFER TO JOINERY SCHEDULE.2. PROVIDE ONE ADJUSTABLE SHELF TO EACH CUPBOARD, WHITE MELAMINE FINISH UNO.3. CUPBOARDS TO HAVE HAFELE HINGES 90/170 DEGREE OPENING, ALL METAL SPRUNG FULLY CONCEALED HINGES TO SUIT DOOR WEIGHT AND CONFIGURATION.4. TOP DRAWER FITTED WITH A PENCIL TRAY INSERT.5. DRAWERS FITTED WITH HAFELE FULLY EXTENDABLE HEAVY DUTY SELF CLOSING RUNNERS, LENGTH TO SUIT CARCASS.6. DRAWERS WITH GANG LOCK, HAFELE SYMO 3000 LOCKING SYSTEM TO SUIT DRAWER CONFIGURATION AS NOMINATED. KEY TO BE JOINERY MASTER KEY SYSTEM DISTINCT TO LOCK SYSTEM, UNO7. KEY DRAWERS AND ADJACENT CABINETS WITHIN THE SAME AREA ALIKE, AND ALL OTHER INDIVIDUAL COUNTERS TO BE KEYED TO DIFFER. CONFIRM WITH CLIENT LOCK/ KEY REQUIREMENTS.8. CABINETS FITTED WITH LAMINATE 3M BRAND RUBBER BUFFERS BETWEEN ALL CLOSING SURFACES. ADHESIVE APPLIED.9. CABINET DOOR/ DRAWERS TO BE RECESSED 20mm FROM THE BENCH TOP FINISHED EDGE.10. PROVIDE GABLE SPACERS TO CABINETS AT JUNCTION WITH WALLS. ALL EXPOSED EDGES FINISHED TO MATCH ADJACENT SURFACE.11. SILCONE SEAL JUNCTION OF BENCH TOP TO WALL WITH APPROVED SEALANT12. ALL SELECTED LAMINATES TO BE ON LAMINEX EO BOARD/ SUBSTRATES (OR EQUAL APPROVED) TO SUIT JOINERY LOCATION & APPLICATION
BB BARREL BOLTC.O.S CHECK ON SITEIBW INSTANT BOILING WATER UNIT BY OTHERSLKC LOCK (CABINET/ DRAWER)PTD PAPER TOWEL DISPENSERMX MIXERS SINKSD SOAP DISPENSERST STONETM TIMBERLAM LAMNOM. NOMINALUNO UNLESS NOTED OTHERWISE
The location of existing walls and structure have been provided to AGArchitects by others.As such AG Architects cannot warrant or verify the accuracy of existinglayout and takes no responsibility for discrepancies in measurementsassociated with setout of new work joining into existing elements.Where setout dimensions of new work are critical in order to join intoexisting it is the responsibility of the builder to check and confirm location& nature of all existing elements prior to setting out; fabrication; andconstruction of new works.All discrepancies between site conditions & those shown on drawings areto be referred to the architect for further instructions.
As indicated (@ A1)
16/1
2/20
13 6
:29:
40 P
M
1
JOINERY DETAIL - NACINFORMATION COUNTER
OPTION BIssue Date
Author
1039-A-WD-84.12B
CDPOM JACKSON'S INTERNATIONAL
AIRPORT ITB UPGRADEPORT MORESBY PNG
SCALE: (@ A1)1 LGE- NAC INFORMATION DESK- PLAN VIEW- B
SCALE: (@ A1)2 LGE- NAC INFORMATION DESK- VIEW 1- BSCALE: (@ A1)3 LGE- NAC INFORMATION DESK- VIEW 3- B
SCALE: (@ A1)4 LGE- NAC INFORMATION DESK- END ELEVATION- B
Issue Description Date By1 PRELIMINARY ISSUE FOR CLIENT FEEDBACK 13/12/13 NAS
STONE COUNTERTOP
STONE PANEL FACINGKWILA LEDGE
STONE PANEL FACING
KWILA BOTTOM RAIL38 THICK DRESSED
RECESSED KICKBOARD- LAMINATE FINISH
RETURN SKIRTINGTO FACE OF KICKBOARD
3838 STAINLESS STEEL SLIDING RAILS TO MATCH EXISTNG
KWILA EDGING92x38 DRESSED
4
84.13
Sim6
84.13
350
750
OPEN UNDER
120
120
340
150
FINISH DADO RAILAT FACE OF COUNTERTOPRETURN GABLE
STONE COUNTERTOP
DRAWERS - SELECTEDLAMINATE. TOP DRAWERKEY LOCKABLEFILE DRAWER
RECESSED KICKBOARD
BENCHTOP GABLESPACER AGAINST WALL
COUNTER CARCASS -LAMINATE FINISH
COUNTERTOP RETURNGABLE TAKEN DOWN TOTOP OF KWILA BOTTOM RAIL
ALLOW TO PROVIDE A GROMMETHOLE IN THE BENCHTOP WITHADJUSTABLE COVER, NOM. 80mmDIAMETER, 40mm CLEAR OF ALL EDGES.COLOUR TO MATCH BENCHTOP.CONFIRM EXACT LOCATION WITH CLIENT.
BENCHTOP -LAMINATE FINISH
STONE COUNTERTOP
STONE PANEL FACINGKWILA LEDGE SUPPORTEDON ANGLES FIXED TOSUB-STRUCTURESTONE PANEL FACING
The location of existing walls and structure have been provided to AGArchitects by others.As such AG Architects cannot warrant or verify the accuracy of existinglayout and takes no responsibility for discrepancies in measurementsassociated with setout of new work joining into existing elements.Where setout dimensions of new work are critical in order to join intoexisting it is the responsibility of the builder to check and confirm location& nature of all existing elements prior to setting out; fabrication; andconstruction of new works.All discrepancies between site conditions & those shown on drawings areto be referred to the architect for further instructions.
Issue Description Date By1 PRELIMINARY ISSUE FOR CLIENT FEEDBACK 13/12/13 NAS
5
84.14
84.14 2 84.143
350 550 2328
2269
KWILA
LEDG
E
- FIT COUNTERS NEATLYBETWEEN WALLS- BENCHTOPS FIXED TOSUPPORTS FIXED TO FACEOF WALLS
50ALLOW TO PROVIDE TWO GROMMETHOLES IN THE BENCHTOP WITHADJUSTABLE COVERS, NOM. 80mmDIAMETER, 40mm CLEAR OF ALL EDGES.COLOUR TO MATCH BENCHTOP.CONFIRM EXACT LOCATION WITH CLIENT.
5
84.14
40 EQ. EQ. EQ. EQ. 40
1200
4076
030
0
750
STONE COUNTERTOP
STONE PANEL FACINGKWILA LEDGE
STONE PANEL FACING
KWILA BOTTOM RAIL38 THICK DRESSED
LAMINATE KICKBOARD
RETURN SKIRTINGTO FACE OF KICKBOARD
ROLLER SHUTTER DRUMCONCEALED IN BULKHEAD
ROLLER SHUTTER GUIDECONCEALED IN STUD WALL
5
84.14
350
750
TAKE SKIRTING TOFACE OF CARCASS
BENCHTOP -SELECTED LAMINATE
STONE COUNTERTOP
BULKHEAD TOCONCEAL ROLLERSHUTTER DRUM
CARCASS -SELECTED LAMINATE
OPEN UNDER
RECESSED KICKBOARD
RETURN SKIRTING TOFACE OF KICKBOARD.
RETURN SKIRTINGTO FACE OF KICKBOARD
FACE OF KICKBOARDSETBACK 50mm FROMFACE OF WALL
FINISH DADO ATFACE OF COUNTER-TOP RETURN GABLE
KWILA LEDGE
KWILA BOTTOM RAIL
SHUTTER & ASSOCIATEDACCESSORIES NOT SHOWN,REFER TO NOTES ON ELEVATIONS
350 550
150 300 600
BENC
HTOP
& LE
DGE
750
300
COUN
TERT
OP11
00
10 100
BENCHTOP -LAMINATE FINISH
STONE COUNTERTOP
STONE PANEL FACINGKWILA LEDGE SUPPORTEDON ANGLES FIXED TOSUB-STRUCTURESTONE PANEL FACING
The location of existing walls and structure have been provided to AGArchitects by others.As such AG Architects cannot warrant or verify the accuracy of existinglayout and takes no responsibility for discrepancies in measurementsassociated with setout of new work joining into existing elements.Where setout dimensions of new work are critical in order to join intoexisting it is the responsibility of the builder to check and confirm location& nature of all existing elements prior to setting out; fabrication; andconstruction of new works.All discrepancies between site conditions & those shown on drawings areto be referred to the architect for further instructions.
Issue Description Date By1 PRELIMINARY ISSUE FOR CLIENT FEEDBACK 13/12/13 NAS
SELECTED STONE RAISED COUNTERTOP WITH 3 TO 4mm ARRISED EDGE
SELECTED LAMINATED FINISH TO INTERNALCARCASS OF RAISED COUNTER TOP
ALIGN JOINT WITH GABLE BELOW
LOCKABLE CABINET UNDER, TYPICAL WITH ONEADJUSTABLE SHELF IN WHITE MELAMINE
DRAWERS - JF1:- TOP DRAWER: PROVIDE A REMOVABLE PENCIL TRAY,- BOTTOM DRAWER: PROVIDE FILE SUSPENSION SYSTEMCAPABLE OF HOUSING A4 AND FOOLSCAP FILES
FRAMING SHOWN INDICATIVELY ONLY.PROVIDE INTERNAL SUPPORTS &PACKERS AS REQUIRED. 75
0
600
BENCHTOP - CLAM5
GABLE SPACER TO SUIT
C.O.S2900 NOM.
RECESSED KICKBOARD - JF2
PROVIDE UNDER BENCH CABLEMANAGEMENT TRAY TO SUIT
UNDER BENCH BOX IN DUCT FOR POWERAND DATA RETICULATIONTO AS 3000 ELECTRICAL INSTALLATION &AS3350 WIRING INSTALLATION
UNDER BENCH ACCESS FOR POWER ANDDATA - ALLOW TWO GROMMET HOLES (INTOTAL) WITH ADJUSTABLE COVERS, NOM.80mm DIA. , 40mm CLEAR OF ALL EDGES,COLOUR TO MATCH, CONFIRM CLIENT FOREXACT LOCATION.
PROVIDE COUNTERTOP SUPPORT FINS TO SUITCOUNTERTOP WEIGHT
PROVIDE ABOVE BENCH - 2 DOUBLE GPOs &1 DUAL DATA OUTLETS
PROVIDE UNDER BENCH SERVICES:2 DOUBLE GPOs AND 1 DUAL DATAOUTLETS
JOINERY NOTES1. ALL DIMENSIONS ARE TO BE CHECKED ON SITE PRIOR TO CONSTRUCTION.2. THIS SECTION OF WORK SHALL BE READ IN CONJUNCTION WITH FIXTURES &FINISHES SCHEDULES
DESIGN NOTES- SERVICE/ RECEPTION COUNTERSTYPICAL1. JOINERY / CABINET DOOR HANDLES - REFER TO JOINERY SCHEDULE.2. PROVIDE ONE ADJUSTABLE SHELF TO EACH CUPBOARD, WHITE MELAMINEFINISH UNO.3. CUPBOARDS TO HAVE HAFELE HINGES 90/170 DEGREE OPENING, ALLMETAL SPRUNG FULLY CONCEALED HINGES TO SUIT DOOR WEIGHT ANDCONFIGURATION.4. TOP DRAWER FITTED WITH A PENCIL TRAY INSERT.5. DRAWERS FITTED WITH HAFELE FULLY EXTENDABLE HEAVY DUTY SELFCLOSING RUNNERS, LENGTH TO SUIT CARCASS.6. DRAWERS WITH GANG LOCK, HAFELE SYMO 3000 LOCKING SYSTEM TOSUIT DRAWER CONFIGURATION AS NOMINATED. KEY TO BE JOINERY MASTERKEY SYSTEM DISTINCT TO LOCK SYSTEM, UNO7. KEY DRAWERS AND ADJACENT CABINETS WITHIN THE SAME AREA ALIKE,AND ALL OTHER INDIVIDUAL COUNTERS TO BE KEYED TO DIFFER. CONFIRMWITH CLIENT LOCK/ KEY REQUIREMENTS.8. CABINETS FITTED WITH LAMINATE 3M BRAND RUBBER BUFFERS BETWEENALL CLOSING SURFACES. ADHESIVE APPLIED.9. CABINET DOOR/ DRAWERS TO BE RECESSED 20mm FROM THE BENCH TOPFINISHED EDGE.10. PROVIDE GABLE SPACERS TO CABINETS AT JUNCTION WITH WALLS. ALLEXPOSED EDGES FINISHED TO MATCH ADJACENT SURFACE.11. SILCONE SEAL JUNCTION OF BENCH TOP TO WALL WITH APPROVEDSEALANT12. ALL SELECTED LAMINATES TO BE ON LAMINEX EO BOARD/ SUBSTRATES(OR EQUAL APPROVED) TO SUIT JOINERY LOCATION & APPLICATION
BB BARREL BOLTC.O.S CHECK ON SITEIBW INSTANT BOILING WATER UNIT BY OTHERSLKC LOCK (CABINET/ DRAWER)PTD PAPER TOWEL DISPENSERMX MIXERS SINKSD SOAP DISPENSERST STONETM TIMBERLAM LAMNOM. NOMINALUNO UNLESS NOTED OTHERWISE
ABBREVIATED NOTES
1100
750
WALL BEYOND
STONE COUNTER TOP WITH3 TO 4mm ARRISED EDGE
COUNTERTOP SUPPORT FINS- CLAM5 COMPACT LAMINATE
GROMMET HOLE
CABLE TRAY
BENCHTOP - CLAM5
JOINERY FRAMING SHOWNINDICATIVELY ONLY.PROVIDE SUPPORTS ANDPACKERS TO SUIT
BOX IN DUCT FOR POWER &DATA RETICULATION TOAS 3000
350 600
DRAWER CABINETS - JF1
950
350
KWILA SKIRTING IN SINGLEPIECE
1100
KWILA DADO RAIL
COUNTERTOP, FULL GABLEFRONT/ ENDS - STONE S4
WALLS NOT DRAWN FOR CLARITY
GABLE SPACER TO END WALLBENCHTOP - COMPACTLAMINATE CLAM5
Upper Ground Level www.agarchitects.net.au3/47 Anderson St [email protected] Valley Q 4006 ph. (07) 3852 1355
The location of existing walls and structure have been provided to AGArchitects by others.As such AG Architects cannot warrant or verify the accuracy of existinglayout and takes no responsibility for discrepancies in measurementsassociated with setout of new work joining into existing elements.Where setout dimensions of new work are critical in order to join intoexisting it is the responsibility of the builder to check and confirm location& nature of all existing elements prior to setting out; fabrication; andconstruction of new works.All discrepancies between site conditions & those shown on drawings areto be referred to the architect for further instructions.
HANDWASH BASIN.SOAP DISPENSER &PAPER TOWEL DISPENSEROVER NOT SHOWN.
SCULLERY SINK
RECESSED KICKBOARD -JF7 LAMINATE FINISH
700
20580
320
600
750
150
CUPBOARD DOORS -JF7 LAMINATE FINISH
OPEN
370 12001200
OVERHEAD OPENSHELVES - JF7 LAMINATE
FIRE EXTIGUISHER& FIRE BLANKET
JOINERY NOTES1. ALL DIMENSIONS ARE TO BE CHECKED ON SITE PRIOR TO CONSTRUCTION.2. THIS SECTION OF WORK SHALL BE READ IN CONJUNCTION WITH JOINERYFINISHES; WALL FINISHES; FIXTURES & FITTINGS SCHEDULES.
DESIGN NOTES- VIP KITCHEN & SERVERYTYPICAL1. JOINERY / CABINET DOOR HANDLES - REFER TO JOINERY SCHEDULE.2. SINK/ TAPWARE/ SOAP & PAPER TOWEL DISPENSERS SHOWN INDICATIVELY.REFER TO FIXTURES AND FINISHES SCHEDULES.3. LOWER CUPBOARDS TO HAVE ONE ADJUSTABLE SHELF, WHITE MELAMINEFINISH UNO.4. BENCHTOPS TO BE SOLID COMPACT LAMINATE, NOM. 18mm THICK. REFERSCHEDULE FOR COLOUR.5. CUPBOARDS TO HAVE HAFELE HINGES 90/170 DEGREE OPENING, ALL METALSPRUNG FULLY CONCEALED HINGES TO SUIT DOOR WEIGHT ANDCONFIGURATION.6. DRAWERS FITTED WITH HAFELE FULLY EXTENDABLE HEAVY DUTY SELFCLOSING RUNNERS, LENGTH TO SUIT CARCASS.7. LOCKABLE DRAWERS FITTED WITH HAFELE SYMO 3000 LOCKING SYSTEM TOSUIT DRAWER CONFIGURATION AS NOMINATED. KEY TO BE JOINERY MASTERKEY SYSTEM DISTINCT TO LOCK SYSTEM, UNO.8. KEY DRAWERS AND ADJACENT CABINET WITHIN THE SAME AREA ALIKE, ANDALL OTHER INDIVIDUAL COUNTER TO BE KEYED TO DIFFER. CONFIRM WITH CLIENTFOR LOCK/ KEY REQUIREMENTS.9. PROVIDE 3M BRAND RUBBER BUFFERS BETWEEN ALL CLOSING SURFACES.ADHESIVE APPLIED.10. KICKBOARDS TO BE 50mm RECESSED FROM FINISHED FACE OF CUPBOARDS.11. CABINET DOORS/DRAWERS TO BE 20mm RECESSED FROM BENCHTOPFINISHED EDGE.12. SILICONE SEAL JUNCTION OF SPLASHBACK TO BENCH TOP, ANDSPLASHBACK TO WALL WITH APPROVED SEALANT .13. ALL SELECTED LAMINATES TO BE ON LAMINEX EO BOARD/ SUBSTRATES (OREQUAL APPROVED) TO SUIT JOINERY LOCATION & APPLICATION.16. CUPBOARD DOORS AND DRAWER FRONTS TO HAVE ABS MATCHING EDGESTRIPS.
MN
TN
Upper Ground Level www.agarchitects.net.au3/47 Anderson St [email protected] Valley Q 4006 ph. (07) 3852 1355
The location of existing walls and structure have been provided to AGArchitects by others.As such AG Architects cannot warrant or verify the accuracy of existinglayout and takes no responsibility for discrepancies in measurementsassociated with setout of new work joining into existing elements.Where setout dimensions of new work are critical in order to join intoexisting it is the responsibility of the builder to check and confirm location& nature of all existing elements prior to setting out; fabrication; andconstruction of new works.All discrepancies between site conditions & those shown on drawings areto be referred to the architect for further instructions.
As indicated (@ A1)
16/1
2/20
13 6
:29:
46 P
M
1
JOINERY DETAILS - VIPKITCHEN SHEET 1
Issue Date
LA
1039-A-WD-84.17
CDPOM JACKSON'S INTERNATIONAL
AIRPORT ITB UPGRADEPORT MORESBY PNG
Issue Description Date By1 PRELIMINARY ISSUE FOR CLIENT FEEDBACK 13/12/13 NAS
SCALE: 1 : 20 (@ A1)1 L1F- VIP KITCHEN
SCALE: 1 : 20 (@ A1)2 L1F- VIP KITCHEN 1
SCALE: 1 : 20 (@ A1)3 L1F- VIP KITCHEN 2
STONE COUNTERTOP& FACING
955
145
1100
DADO RAIL FINISHEDAT FACE OF COUNTERTOPGABLE
KWILA SKIRTINGCONTINUES AROUNDFACE OF SERVERY
BULKHEAD
STONE COUNTERTOP& GABLE RETURN FACING
KWILA SKIRTINGCONTINUES AROUNDFACE OF SERVERY
BULKHEAD
STONE GABLE RETURN
900
4071
514
5
STONE BENCHTOP
350
120
LAMINATE FACING
145
955
STONE COUNTERTOP& FACING
KWILA SKIRTING
DRAWERS600
DRAWERS600
STONE BENCHTOP
860
4018
020
DRAWERS -LAMINATE
RECESSEDKICKBOARD- LAMINATE
GABLE SPACER
BULKHEAD
350 600
2050
FREEZER
BULKHEAD
STONE COUNTERTOP
STONE COUNTERTOPRETURN GABLE
FRIDGEFRIDGE
KWILA SKIRTING
LAMINATE FACING
STONE BENCHTOP
4086
0 1080
20
LAMINATE CARCASS
120
DRAWERS600
DRAWERS600
DRAWERS600
CUTLERY
PLATES
PLATES
Upper Ground Level www.agarchitects.net.au3/47 Anderson St [email protected] Valley Q 4006 ph. (07) 3852 1355
The location of existing walls and structure have been provided to AGArchitects by others.As such AG Architects cannot warrant or verify the accuracy of existinglayout and takes no responsibility for discrepancies in measurementsassociated with setout of new work joining into existing elements.Where setout dimensions of new work are critical in order to join intoexisting it is the responsibility of the builder to check and confirm location& nature of all existing elements prior to setting out; fabrication; andconstruction of new works.All discrepancies between site conditions & those shown on drawings areto be referred to the architect for further instructions.
Issue Description Date By1 PRELIMINARY ISSUE FOR CLIENT FEEDBACK 13/12/13 NAS
3
84.19
40 EQ. EQ. EQ. EQ. 40
300
1100
750
STONE COUNTERTOP
STONE PANEL FACINGKWILA LEDGE
STONE PANEL FACING
KWILA BOTTOM RAILLAMINATE KICKBOARD
RETURN SKIRTINGTO FACE OF KICKBOARD
DADO TO FINISHAT FACE OF GABLE
CLEAR OPENING
84.19 2
350 550 1122
2469
50 350
BUILD OUTWALL
KWILA
LEDG
E
84.194
ALLOW TO PROVIDE TWO GROMMETHOLES IN THE BENCHTOP WITHADJUSTABLE COVER, NOM. 80mmDIAMETER, 40mm CLEAR OF ALL EDGES.COLOUR TO MATCH BENCHTOP.CONFIRM EXACT LOCATION WITH CLIENT.
- FIT COUNTER & BENCHTOPNEATLY BETWEEN WALLS- BENCHTOPS FIXED TOSUPPORTS FIXED TO FACEOF WALLS
3
84.19
TAKE SKIRTING TOFACE OF CARCASS
BENCHTOP -SELECTED LAMINATE
STONE COUNTERTOP
CARCASS -SELECTED LAMINATE
OPEN UNDER
350
750
3
84.19
BENCHTOP -LAMINATE FINISH
STONE COUNTERTOP
STONE PANEL FACINGKWILA LEDGE SUPPORTEDON ANGLES FIXED TOSUB-STRUCTURESTONE PANEL FACING
KWILA BOTTOM RAIL38mm THICKLAMINATE KICKBOARD
CARCASS -LAMINATE FINISH
WALL BUILDOUTIN ELEVATION
COUN
TERT
OP11
00BE
NCHT
OP &
LEDG
E75
0
150 350 550
300 600
10 100
Upper Ground Level www.agarchitects.net.au3/47 Anderson St [email protected] Valley Q 4006 ph. (07) 3852 1355
The location of existing walls and structure have been provided to AGArchitects by others.As such AG Architects cannot warrant or verify the accuracy of existinglayout and takes no responsibility for discrepancies in measurementsassociated with setout of new work joining into existing elements.Where setout dimensions of new work are critical in order to join intoexisting it is the responsibility of the builder to check and confirm location& nature of all existing elements prior to setting out; fabrication; andconstruction of new works.All discrepancies between site conditions & those shown on drawings areto be referred to the architect for further instructions.
1 : 20 (@ A1)
16/1
2/20
13 6
:30:
17 P
M
1
JOINERY DETAILS -PASSPORT CHECK
COUNTERIssue Date
LA
1039-A-WD-84.19
CDPOM JACKSON'S INTERNATIONAL
AIRPORT ITB UPGRADEPORT MORESBY PNG
Issue Description Date By1 PRELIMINARY ISSUE FOR CLIENT FEEDBACK 13/12/13 NAS
ALLOW TO PROVIDE TWO GROMMETHOLES TO EACH BENCHTOPWITH ADJUSTABLE COVERS, NOM.80mm DIAMETER, 40mm CLEAR OFALL EDGES. COLOUR TO MATCHBENCHTOP. CONFIRM EXACT LOCATIONWITH CLIENT.
4
84.20
KWILA LEDGE KWILA LEDGE
300
750
1100
STONE COUNTERTOPSTONE PANEL FACING
KWILA LEDGE
KWILA BOTTOM RAIL38 THICK DRESSED
LAMINATEKICKBOARD
RETURN SKIRTINGTO FACE OF KICKBOARD
RETURN DADO RAILTO FACE OF COUNTERTOPGABLE
4
84.20
750
350
150
340
1201
20
40 80
10 100DRAWERS
450DRAWERS
450
300
BENCHTOP -SELECTED LAMINATE
STONE COUNTERTOP
CARCASS -SELECTED LAMINATE
OPEN UNDER
OPEN UNDER
DRAWERS -SELECTED LAMINATERECESSED KICKBOARD
GABLE SPACER
GABLES TOSUPPORT BENCHTOPAT EITHER SIDE OFJOINT
BENCHTOPGABLE
COUNTERTOPGABLE
KWILABOTTOM RAILKICKBOARD
COUNTERTOPSUPPORT FINS -LAMINATE FINISH
COUNTERTOPSUPPORT FINS -LAMINATE FINISH
BENCHTOP -LAMINATE FINISH
STONE COUNTERTOP
STONE PANEL FACINGKWILA LEDGE SUPPORTEDON ANGLES FIXED TOSUB-STRUCTURESTONE PANEL FACING
JOINERY NOTES1. ALL DIMENSIONS ARE TO BE CHECKED ON SITE PRIOR TO CONSTRUCTION.2. THIS SECTION OF WORK SHALL BE READ IN CONJUNCTION WITH FIXTURES &FINISHES SCHEDULES
DESIGN NOTES- SERVICE/ RECEPTION COUNTERSTYPICAL1. JOINERY / CABINET DOOR HANDLES - REFER TO JOINERY SCHEDULE.2. PROVIDE ONE ADJUSTABLE SHELF TO EACH CUPBOARD, WHITE MELAMINEFINISH UNO.3. CUPBOARDS TO HAVE HAFELE HINGES 90/170 DEGREE OPENING, ALLMETAL SPRUNG FULLY CONCEALED HINGES TO SUIT DOOR WEIGHT ANDCONFIGURATION.4. TOP DRAWER FITTED WITH A PENCIL TRAY INSERT.5. DRAWERS FITTED WITH HAFELE FULLY EXTENDABLE HEAVY DUTY SELFCLOSING RUNNERS, LENGTH TO SUIT CARCASS.6. DRAWERS WITH GANG LOCK, HAFELE SYMO 3000 LOCKING SYSTEM TOSUIT DRAWER CONFIGURATION AS NOMINATED. KEY TO BE JOINERY MASTERKEY SYSTEM DISTINCT TO LOCK SYSTEM, UNO7. KEY DRAWERS AND ADJACENT CABINETS WITHIN THE SAME AREA ALIKE,AND ALL OTHER INDIVIDUAL COUNTERS TO BE KEYED TO DIFFER. CONFIRMWITH CLIENT LOCK/ KEY REQUIREMENTS.8. CABINETS FITTED WITH LAMINATE 3M BRAND RUBBER BUFFERS BETWEENALL CLOSING SURFACES. ADHESIVE APPLIED.9. CABINET DOOR/ DRAWERS TO BE RECESSED 20mm FROM THE BENCH TOPFINISHED EDGE.10. PROVIDE GABLE SPACERS TO CABINETS AT JUNCTION WITH WALLS. ALLEXPOSED EDGES FINISHED TO MATCH ADJACENT SURFACE.11. SILCONE SEAL JUNCTION OF BENCH TOP TO WALL WITH APPROVEDSEALANT12. ALL SELECTED LAMINATES TO BE ON LAMINEX EO BOARD/ SUBSTRATES(OR EQUAL APPROVED) TO SUIT JOINERY LOCATION & APPLICATION
Upper Ground Level www.agarchitects.net.au3/47 Anderson St [email protected] Valley Q 4006 ph. (07) 3852 1355
The location of existing walls and structure have been provided to AGArchitects by others.As such AG Architects cannot warrant or verify the accuracy of existinglayout and takes no responsibility for discrepancies in measurementsassociated with setout of new work joining into existing elements.Where setout dimensions of new work are critical in order to join intoexisting it is the responsibility of the builder to check and confirm location& nature of all existing elements prior to setting out; fabrication; andconstruction of new works.All discrepancies between site conditions & those shown on drawings areto be referred to the architect for further instructions.
As indicated (@ A1)
16/1
2/20
13 6
:30:
18 P
M
1
JOINERY DETAILS -TRANSFER TICKETING
COUNTERIssue Date
LA
1039-A-WD-84.20
CDPOM JACKSON'S INTERNATIONAL
AIRPORT ITB UPGRADEPORT MORESBY PNG
SCALE: 1 : 20 (@ A1)1 L1B- TRANSFER TICKETING COUNTER
SCALE: 1 : 20 (@ A1)2 L1B- TRANSFER TICKETING COUNTERSCALE: 1 : 20 (@ A1)3 L1B- TRANSFER TICKETING COUNTER 2
SCALE: 1 : 20 (@ A1)4 L1B- TRANSFER TICKETING
SCALE: (@ A1)5 L1B- TRANSFER TICKETING COUNTER
SCALE: (@ A1)6 L1B- TRANSFER TICKETING COUNTER 2
Issue Description Date By1 PRELIMINARY ISSUE FOR CLIENT FEEDBACK 13/12/13 NAS
F
EQ. EQ. EQ. EQ.CONFIRM ON SITE
9890
JOINT SETOUT
400
DADO RAIL FINISHESAT FACE OF GABLE
DADO RAIL FINISHESAT FACE OF FASCIA
JOINT JOINT RETURN UPSTAND.END TO ALIGN WITHCOUNTERTOP EDGE.84.21
23
84.21
PB/PF WALL
STONE UPSTAND.RETURN ON SIDE WALLS
STONE COUNTERTOP& FASCIAVINYL FINISHTO WALL
SKIRTING
150
300
750
3
84.21
150
300
750
STONE UPSTAND.RETURN AT SIDE WALLS.STONE COUNTERTOP& FASCIA
SUPPORT STRUCTUREFIXED TO NOGGING INWALL
400
COUNTERTOPEND GABLEFINISH END OF DADO RAILAT FACE OF GABLE
CONTINUE SKIRTING& VINYL WALL FINISH
COUNTERTOP/FASCIA/UPSTAND JOINTS TOALIGN
FINISH END OF DADO RAILAT FACE OF FASCIA
20°
31°
50 50
1150
FRAMING TO SUIT, PROVIDEBOX IN DUCT FOR POWERAND DATA RETICULATION
150
500
150
100
GROMMET HOLE
200x 20mm REBATE IN FRONTOF CARCASS BASE FORVENTILATION
RECESS PENCIL TRAY
OPEN SHELF UNDERFOR AUDIO EQUIPMENTS BY OTHERS
FORM SLAB PENETRATIONFOR POWER AND DATA
COUNTER TOP IN NOM. 20 DEGREEANGLE
ALLOW UNDER BENCH POWER AND DATA OUTLETSCLIENT WITH CLIENT FOR EXACT REQUIREMENTS
AUDIO EQUIPMENTS BY OTHERS
500
900
150
150
900 11
50
50 50
900
OPEN UNDER
Upper Ground Level www.agarchitects.net.au3/47 Anderson St [email protected] Valley Q 4006 ph. (07) 3852 1355
The location of existing walls and structure have been provided to AGArchitects by others.As such AG Architects cannot warrant or verify the accuracy of existinglayout and takes no responsibility for discrepancies in measurementsassociated with setout of new work joining into existing elements.Where setout dimensions of new work are critical in order to join intoexisting it is the responsibility of the builder to check and confirm location& nature of all existing elements prior to setting out; fabrication; andconstruction of new works.All discrepancies between site conditions & those shown on drawings areto be referred to the architect for further instructions.
