-
MAKE: STYLE:
45
WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED
TOWING CAPACITYFor more information log onto www.curtmfg.com &
for helpful towing tips log onto www.hitchinfo.com
WEIGHT CARRYING:
INSTALLATION TIPS:
INSTALLATION REQUIRES:
VEHICLE PHOTO:
HITCH ILLUSTRATION:
REPRESENTATIVE PHOTO
MAKE SURE YOUR HITCH MATCHES
LEVEL OF DIFFICULTY: MODERATE
MODERATE CHALLENGING
1. BEFORE YOU BEGIN INSTALLATION, READ ALL INSTRUCTIONS
THOROUGHLY. 2. TO EASE INSTALLATION, 2 PEOPLE MAY BE REQUIRED. 3.
USING PROPER TOOLS WILL GREATLY IMPROVE THE QUALITY OF THE INSTALL
AND REDUCE THE TIME REQUIRED. 4. NEED HELP OR HAVE SOME QUESTIONS?
CALL TECHNICAL SUPPORT AT 877.287.8634
Safety glasses should be worn at all times whileinstalling this
product.
YEARS: 2018-CURRENT ALFA ROMEO MODEL: STELVIO SUV
4,000600
TRAILER WEIGHT:TONGUE WEIGHT:
13391 INSTALLATION INSTRUCTIONS
LBS.LBS.
90 MIN.MIN. PRO INSTALL TIME:
NOVICE INSTALL TIME:
IF YOU ARE HESITANT TO UNDERTAKETHIS TASK ON YOUR OWN, CONTACT
AN AUTHORIZED
CURT INSTALLER FOR ADDITIONAL ASSISTANCE.
SCAN FORMORE INFO
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS
ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUNDCURT Manufacturing
LLC. warrants this product to be free of defects in material and/or
workmanship at the time of retail purchase by the original
purchaser. If the product is found to be defective,CURT
Manufacturing LLC. may repair or replace the product at their
option, when the product is returned, prepaid, with proof of
purchase. Alteration to, misuse of, or improper installation of
this productvoids the warranty. CURT Manufacturing LLC.'s liability
is limited to repair or replacement of products found to be
defective, and specifically excludes liability for incidental or
consequential loss or damage.For more information log onto
www.curtmfg.comThis product complies with safety specifications and
requirements for connecting devices and towing systems of the state
of New York, V.E.S.C.Regulation V-5 and SAE J684. 10/30/2020
EASYTORXBITSOCKET
T25T30 SOCKET
10mm3/4"
SOCKET
EXTENSION
6"
RATCHET ROTARY TOOLSAFETY
GLASSESPART REMOVAL
TEMPORARILY REMOVEUNDER BODY PANEL
TRIM UNDERBODY PANEL
FISHWIREHARDWARE
REVERSE FISHWIREHARDWARE
NO DRILL
-
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com
Parts List
DESCRIPTIONPART NUMBERQTYITEM
BOLT,CAR,1/2-13 UNC,1-1/2,GRD8,YZ10-1028761
.250 x 1.00 x 3.00" SQUARE HOLE SPACERCM-SP662
NUT,SER-FLANGE,1/2-13 UNC,GRD8,YZ20-0006263
1/2" FISHWIRE1_2 FISHWIRE64
1. Remove underbody panels from both sides of the vehicle.
PASSENGER SIDEFRAME RAIL
DRIVER SIDEFRAME RAIL
EXISTINGHOLE (ALL)
3
1
2
4 2. Fishwire (1) 1/2" carriage bolt and CM-SP6 spacer into the
rearward most hole in both frame rails. Reverse fishwire the
remaining hardware into the remaining holes in the bottom of the
frame rails. NOTE: Leave fishwires attached. To ease installation
leave the driver side bolts in the frame.
-
INSTALLATION WALKTHROUGH:
For more information log onto www.curtmfg.com
3. Raise hitch into position guiding fishwires through the holes
in the hitch. Remove fishwires and loosely secure hitch with hex
flange nuts.
4. Torque 1/2" hardware to 110 lb-ft.
5. Trim underbody panels using UNDERBODY TRIM DIAGRAM below for
reference and reinstall.
UNDERBODY TRIM DIAGRAM
11 in
5 in
-
GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS.
TRAILER WEIGHT & LBS. TONGUE WEIGHT.
WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED
TOWING CAPACITY ***FOR MORE INFORMATION LOG ONTO
WWW.CURTMFG.COM
HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT
1-877-287-8634
HITCH WEIGHT: LBS.
INSTALL TIME
PROFESSIONAL: MINUTES
NOVICE (DIY): MINUTES
INSTALL NOTES:
INSTALLATION STEPS
PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL
FASTENERSARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE
SOUND.
CURT Manufacturing LLC., warrants this product to be free of
defects in material and/or workmanship at the time of retail
purchase by the original purchaser. If the product is found to be
defective, CURT Manufacturing LLC., may repair or replace the
product, at their option, when the product is returned, prepaid,
with proof of purchase. Alteration to, misuse of, or improper
installation of this product voids the warranty. CURT Manufacturing
LLC.'s liability is limited to repair or replacement of products
found to be defective, and specifically excludes liability for
incidental or consequential loss or damage.This product complies
with safety specifications and requirements for connecting devices
and towing systems of the state of New York, V.E.S.C.Regulation V-5
and SAE J684.
4,000 600
34
45
ALFA ROMEO STELVIO10/30/202013391
90
Scanfor moreinformation
Parts ListDESCRIPTIONPART NUMBERQTYITEM
BOLT,CAR,1/2-13 UNC,1-1/2,GRD8,YZ10-1028761.250 x 1.00 x 3.00"
SQUARE HOLE SPACERCM-SP662NUT,SER-FLANGE,1/2-13
UNC,GRD8,YZ20-00062631/2" FISHWIRE1_2 FISHWIRE64
DRIVER SIDEFRAME RAIL
PASSENGER SIDEFRAME RAIL
EXISTINGHOLE (ALL)
2
1
3
4
1. Remove underbody panels from both sides of the vehicle.
2. Fishwire (1) 1/2" carriage bolt and (1) CM-SP6 spacer into
the rearward most hole in both frame rails. Reverse fishwire
remaining hardware into the remaining holes in the bottom of the
frame rails. NOTE: Leave fishwires attached. To ease installation
leave the driver side bolts in the frame.
3. Raise hitch into position guiding fishwires through the holes
in the hitch. Remove fishwires and loosely secure hitch with hex
flange nuts.
4. Torque 1/2" hardware to 110 lb-ft
5. Trim underbody panels using UNDERBODY TRIM DIAGRAM above for
reference and reinstall.
- Temporarily remove underbody panels- Trim underbody panels-
Fishwire- Reverse fishwire
5 in
11 in
UNDERBODY TRIM DIAGRAM
TOOLS REQUIREDT25 TORX DRIVERT30 TORX DRIVER
10mm SOCKET3/4" SOCKET
6" EXTENSIONRATCHET
ROTARY TOOLSAFETY GLASSES
