MAKE: STYLE:

45

WARNING: NEVER EXCEED YOUR VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITYFor more information log onto www.curtmfg.com & for helpful towing tips log onto www.hitchinfo.com

WEIGHT CARRYING:

INSTALLATION TIPS:

INSTALLATION REQUIRES:

VEHICLE PHOTO:

HITCH ILLUSTRATION:

REPRESENTATIVE PHOTO

MAKE SURE YOUR HITCH MATCHES

LEVEL OF DIFFICULTY: MODERATE

MODERATE CHALLENGING

1. BEFORE YOU BEGIN INSTALLATION, READ ALL INSTRUCTIONS THOROUGHLY. 2. TO EASE INSTALLATION, 2 PEOPLE MAY BE REQUIRED. 3. USING PROPER TOOLS WILL GREATLY IMPROVE THE QUALITY OF THE INSTALL AND REDUCE THE TIME REQUIRED. 4. NEED HELP OR HAVE SOME QUESTIONS? CALL TECHNICAL SUPPORT AT 800.798.0813

Safety glasses should be worn at all times whileinstalling this product.

YEARS: 2018-CURRENT ALFA ROMEO MODEL: STELVIO SUV

4,000600

TRAILER WEIGHT:TONGUE WEIGHT:

13391 INSTALLATION INSTRUCTIONS

LBS.LBS.

90 MIN.MIN. PRO INSTALL TIME:

NOVICE INSTALL TIME:

IF YOU ARE HESITANT TO UNDERTAKETHIS TASK ON YOUR OWN, CONTACT AN AUTHORIZED

CURT INSTALLER FOR ADDITIONAL ASSISTANCE.

SCAN FORMORE INFO

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE ALL FASTENERS ARE TIGHT AND ALL STRUCTURAL COMPONENTS ARE SOUNDCURT Manufacturing LLC. warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective,CURT Manufacturing LLC. may repair or replace the product at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this productvoids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.For more information log onto www.curtmfg.comThis product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684. 2/9/2018

EASYTORXBITSOCKET T25

T30 SOCKET

10mm3/4"

SOCKET

EXTENSION

6"

RATCHET ROTARY TOOLSAFETY

GLASSESPART REMOVAL

TEMPORARILY REMOVEUNDER BODY PANEL

TRIM UNDERBODY PANEL

FISHWIREHARDWARE

REVERSE FISHWIREHARDWARE

NO DRILL

INSTALLATION WALKTHROUGH:

For more information log onto www.curtmfg.com

Parts List

DESCRIPTIONPART NUMBERQTYITEM

CARRIAGE BOLT1/2-13 x 1 1/261

.250 x 1.00 x 3.00" SQUARE HOLE SPACERCM-SP662

HEX FLANGE NUTHFN 1213, GR863

1/2" FISHWIRE1_2 FISHWIRE64

1. Remove underbody panels from both sides of the vehicle.

PASSENGER SIDEFRAME RAIL

DRIVER SIDEFRAME RAIL

EXISTINGHOLE (ALL)

3

1

2

4 2. Fishwire (1) 1/2" carriage bolt and CM-SP6 spacer into the rearward most hole in both frame rails. Reverse fishwire the remaining hardware into the remaining holes in the bottom of the frame rails. NOTE: Leave fishwires attached. To ease installation leave the driver side bolts in the frame.

INSTALLATION WALKTHROUGH:

For more information log onto www.curtmfg.com

3. Raise hitch into position guiding fishwires through the holes in the hitch. Remove fishwires and loosely secure hitch with hex flange nuts.

4. Torque 1/2" hardware to 110 lb-ft.

5. Trim underbody panels using UNDERBODY TRIM DIAGRAM below for reference and reinstall.

UNDERBODY TRIM DIAGRAM

11 in

5 in

GROSS LOAD CAPACITY WHEN USED AS A WEIGHT CARRYING HITCH: LBS. TRAILER WEIGHT & LBS. TONGUE WEIGHT.

WARNING: *** DO NOT EXCEED VEHICLE MANUFACTURER'S RECOMMENDED TOWING CAPACITY ***FOR MORE INFORMATION LOG ONTO WWW.CURTMFG.COM

HAVING INSTALLATION QUESTIONS? CALL TECHNICAL SUPPORT AT 1-800-798-0813

HITCH WEIGHT: LBS.

INSTALL TIME

PROFESSIONAL: MINUTES

NOVICE (DIY): MINUTES

INSTALL NOTES:

INSTALLATION STEPS

PERIODICALLY CHECK THIS RECEIVER HITCH TO ENSURE THAT ALL FASTENERSARE TIGHT AND THAT ALL STRUCTURAL COMPONENTS ARE SOUND.

CURT Manufacturing LLC., warrants this product to be free of defects in material and/or workmanship at the time of retail purchase by the original purchaser. If the product is found to be defective, CURT Manufacturing LLC., may repair or replace the product, at their option, when the product is returned, prepaid, with proof of purchase. Alteration to, misuse of, or improper installation of this product voids the warranty. CURT Manufacturing LLC.'s liability is limited to repair or replacement of products found to be defective, and specifically excludes liability for incidental or consequential loss or damage.This product complies with safety specifications and requirements for connecting devices and towing systems of the state of New York, V.E.S.C.Regulation V-5 and SAE J684.

4,000 600

34

45

ALFA ROMEO STELVIO2/9/201813391

90

Scanfor moreinformation

Parts ListDESCRIPTIONPART NUMBERQTYITEM

CARRIAGE BOLT1/2-13 x 1 1/261.250 x 1.00 x 3.00" SQUARE HOLE SPACERCM-SP662HEX FLANGE NUTHFN 1213, GR8631/2" FISHWIRE1_2 FISHWIRE64

DRIVER SIDEFRAME RAIL

PASSENGER SIDEFRAME RAIL

EXISTINGHOLE (ALL)

2

1

3

4

1. Remove underbody panels from both sides of the vehicle.

2. Fishwire (1) 1/2" carriage bolt and (1) CM-SP6 spacer into the rearward most hole in both frame rails. Reverse fishwire remaining hardware into the remaining holes in the bottom of the frame rails. NOTE: Leave fishwires attached. To ease installation leave the driver side bolts in the frame.

3. Raise hitch into position guiding fishwires through the holes in the hitch. Remove fishwires and loosely secure hitch with hex flange nuts.

4. Torque 1/2" hardware to 110 lb-ft

5. Trim underbody panels using UNDERBODY TRIM DIAGRAM above for reference and reinstall.

- Temporarily remove underbody panels- Trim underbody panels- Fishwire- Reverse fishwire

5 in

11 in

UNDERBODY TRIM DIAGRAM

TOOLS REQUIREDT25 TORX DRIVERT30 TORX DRIVER

10mm SOCKET3/4" SOCKET

6" EXTENSIONRATCHET

ROTARY TOOLSAFETY GLASSES