1473-1-8298 17.12.2012 Operating Instructions Busch-Timer ... · 12/17/2012 · Operating...

1473-1-8298 │ Rev. 01 │ 17.12.2012

Operating Instructions Busch-Timer®

Pos: 2 /#N eus truktur #/Online-Dokumentation (+KN X)/Titelbl ät ter/Ti mer/Titelbl att 6456 @ 26\mod_1343747512852_15.docx @ 226266 @ @ 1

Standard timer control element 6456-500

=== Ende der Liste für Textmar ke Cover ===

Operating Instructions

Busch-Timer®

Operating Instructions | 1473-1-8298 — 2 —

Pos: 4 /#N eus truktur #/Online-Dokumentation (+KN X)/Inhaltsverzeichnis (--> Für alle D okumente <--)/Inhaltsverzeichnis @ 19\mod_1320649044386_15.docx @ 109653 @ @ 1

1 Safety ....................................................................................................................................................................... 3 2 Intended use ............................................................................................................................................................ 3 3 Environment ............................................................................................................................................................. 3 4 Setup and function ................................................................................................................................................... 4

4.1 Modules .................................................................................................................................................. 4 4.1.1 Blind control ............................................................................................................................................ 4 4.2 Features of function and equipment ........................................................................................................ 4

5 Operation ................................................................................................................................................................. 5 5.1 Hints on operation ................................................................................................................................... 5 5.2 Key assignment ...................................................................................................................................... 6 5.3 Manual operation .................................................................................................................................... 6 5.4 Display and icons .................................................................................................................................... 7 5.5 Overview of the menu structure .............................................................................................................. 8 5.6 Adjusting the device ................................................................................................................................ 9 5.6.1 Selecting languages ................................................................................................................................ 9 5.6.2 Setting date and time ............................................................................................................................ 10 5.6.3 RESET (resetting the device) ................................................................................................................ 11 5.7 Operating modes................................................................................................................................... 12 5.7.1 Deleting switching times ........................................................................................................................ 13 5.8 Setting switching times .......................................................................................................................... 14 5.8.1 BLOCK programming ............................................................................................................................ 14 5.8.2 ASTRO function .................................................................................................................................... 16 5.8.3 Individual switching times ...................................................................................................................... 18 5.9 Calling up special functions ................................................................................................................... 19 5.9.1 ASTRO blocking time ............................................................................................................................ 19

6 Technical data ........................................................................................................................................................ 20 7 Mounting / Installation ............................................................................................................................................ 21 === Ende der Liste für Textmar ke TOC ===


Busch-Timer® Safety


Pos: 6 /#N eus truktur #/Online-Dokumentation (+KN X)/Ü berschriften (--> Für alle Dokumente <--)/1. Ebene/S - T/Sicherheit @ 18\mod_1302612791790_15.docx @ 103357 @ 1 @ 1

1 Safety Pos: 7 /#N eus truktur #/Online-Dokumentation (+KN X)/Sicherheitshinweise und Hi nweise (--> Für all e D okumente <--)/Warnhinweise/Sicherheit - 230 V @ 18\mod_1302606816750_15.docx @ 103308 @ @ 1

Warning Electric voltage! Risk of death and fire due to electrical voltage of 230 V. – Work on the 230V supply system may only be performed by authorised electricians! – Disconnect the mains power supply prior to installation and/or disassembly!

Pos: 8 /#N eus truktur #/Online-Dokumentation (+KN X)/Ü berschriften (--> Für alle Dokumente <--)/1. Ebene/A - F/Bes timmungsgemäßer Gebrauch @ 18\mod_1302763321316_15.docx @ 103483 @ 1 @ 1

2 Intended use Pos: 9 /#N eus truktur #/Online-Dokumentation (+KN X)/Bes timmungsgemäßer Gebrauch (--> Für alle Dokumente <--)/Busch-Di mmer /Besti mmungsgemäßer Gebr auch @ 23\mod_1335350449857_15.docx @ 208763 @ @ 1

The device is to be used exclusively with the components that are supplied and licensed as described in chapter "Setup and function". Pos: 10 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/1. Ebene/U - Z/U mwelt @ 18\mod_1302614158967_15.docx @ 103383 @ 1 @ 1

3 Environment Pos: 11 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Sicherheitshinweise und Hinweise (--> Für alle Dokumente <--)/Hinweise - U mwelt/Hi nweis - U mwelt - Hi nweis El ektr ogeräte @ 18\mod_1302763973434_15.docx @ 103500 @ @ 1

Consider the protection of the environment! Used electric and electronic devices must not be disposed of with domestic waste. – The device contains valuable raw materials which can be recycled. Therefore, dispose of the

device at the appropriate collecting depot. Pos: 12 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Sicherheitshinweise und Hinweise (--> Für alle Dokumente <--)/Hinweise - U mwelt/Hi nweis - U mwelt - Entsorgung Elektroger äte @ 20\mod_1325760695972_15.docx @ 136583 @ @ 1

All packaging materials and devices bear the markings and test seals for proper disposal. Always dispose of the packaging material and electric devices and their components via the authorized collecting depots and disposal companies. The products meet the legal requirements, in particular the laws governing electronic and electrical devices and the REACH ordinance. (EU Directive 2002/96/EC WEEE and 2002/95/EC RoHS) (EU REACH ordinance and law for the implementation of the ordinance (EC) No.1907/2006) Pos: 13 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Steuer modul e - Online-Dokumentation (--> Für alle Dokumente <--)/++++++++++++ Seitenumbruch ++++++++++++ @ 9\mod_1268898668093_0.docx @ 52149 @ @ 1


Busch-Timer® Setup and function


Pos: 14 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/1. Ebene/A - F /Aufbau und Funkti on @ 11\mod_1279185435352_15.docx @ 83027 @ 111 @ 1

4 Setup and function Pos: 15 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Aufbau und Funkti on/Ti mer/Verwendung 6456 @ 26\mod_1343813539814_15.docx @ 226375 @ 2 @ 1

The timer control element serves for the manual and time-controlled switching of roller shutters and blinds. Pos: 16 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Steuer modul e - Online-Dokumentation (--> Für alle Dokumente <--)/++++++++++++ 1 Leerzeil e Abs tand ++++++++++++ @ 24\mod_1337929289045_0.docx @ 213673 @ 2 @ 1

Pos: 17 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/2. Ebene/M - O/M odul e @ 26\mod_1343044917069_15.docx @ 224737 @ 32 @ 1

4.1 Modules Pos : 18 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Bedi enung Modul e - 6456 @ 26\mod_1343801880407_15.docx @ 226297 @ 2222 @ 1

Note The device can only be operated with a central cover plate 6435-....

4.1.1 Blind control

6418 U 6435-… 6456 Fig. 1: Module for blind control The timer is used for blind control in connection with flush-mounted insert 6418 U. Pos: 19 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/2. Ebene/A - F /Funkti ons- und Ausstattungsmer kmal e @ 23\mod_1336557630140_15.docx @ 209136 @ 3222 @ 1

4.2 Features of function and equipment Pos : 20 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Aufbau und Funkti on/Ti mer/Funkti onen 6456 @ 26\mod_1343813599999_15.docx @ 226389 @ 2 @ 1

• With astro program • Individual astro displacement and astro blocking time • The shades can be manually operated at any time • Easy adjustment using menu and text-based display • Factory-set switching times can be individually adjusted • Automatic summer/wintertime switch-over • Switching times/programs are safely stored in the event of a mains power failure • 14 hours power reserve for time and date (maintenance-free as a capacitor) • Simple toggling between manual / automatic / holiday mode • Control element is adjustable without flush-mounted insert • 2 switching times per day can be freely adjusted for each day of the week • Astro switching times and switching times can be combined Pos: 21 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Steuer modul e - Online-Dokumentation (--> Für alle Dokumente <--)/++++++++++++ Seitenumbruch ++++++++++++ @ 9\mod_1268898668093_0.docx @ 52149 @ 1 @ 1


Busch-Timer® Operation


Pos: 22 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/1. Ebene/A - F /Bedi enung @ 11\mod_1279185541649_15.docx @ 83043 @ 21 @ 1

5 Operation Pos: 23 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/2. Ebene/G - L/Hi nweise zur Bedienung @ 28\mod_1347261113115_15.docx @ 232443 @ 22 @ 1

5.1 Hints on operation Pos : 24 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Hi nweise zum Betrieb und zur Bedi enung - 6456 @ 26\mod_1343801687122_15.docx @ 226283 @ @ 1

In the event of a power failure, the internal clock continues to operate for about 14 hours. After this the time and date have to be reprogrammed. All other data remain saved. The operating element can be removed from the flush-mounting insert for approximately 20 minutes and adjusted separately. A total of 2 switching times per day can be set: Preset block switching times – Mon–Fri open: 07:00 – Mon–Fri close: 20:00 – Sat–Sun open: 08:00 – Sat–Sun close: 21:00 The system changes automatically between winter and summer time. If the display is on --:-- , this can mean the following: – no time has been set – the memory is not occupied – the function is not active Flashing numbers / values can be changed. If no entry is made, the display switches back to the operating mode after 1 minute. The times of the menus BLOCK, ASTRO, INDIVIDUAL can be combined with one another. Pos: 25 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Steuer modul e - Online-Dokumentation (--> Für alle Dokumente <--)/++++++++++++ Seitenumbruch ++++++++++++ @ 9\mod_1268898668093_0.docx @ 52149 @ 2 @ 1




Pos: 26 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/2. Ebene/S - T /Tastenbel egung @ 23\mod_1336978335991_15.docx @ 209274 @ 22 @ 1

5.2 Key assignment Pos : 27 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Tas tenbel egung - 6455_6456 Jal ousie @ 26\mod_1343374210951_15.docx @ 225663 @ 2 @ 1

Fig. 2: Button assignment of cover pate Button Function In setting mode Adjusting values Deleting switching times

Calling up menu level and switching to setting mode

Return to operating mode

Press all buttons of the rocker switch simultaneously for approx. 5 seconds

Blind UP (bright) Select menu item Adjust values

Blind DOWN (dark)

Confirmation Select menu Accept value

Pos: 28 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/2. Ebene/M - O/M anuelle Bedi enung @ 28\mod_1346940429935_15.docx @ 230994 @ 232 @ 1

5.3 Manual operation Pos : 29 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/M anuelle Bedi enung 6455_6456 Jalousie @ 28\mod_1346940513035_15.docx @ 231007 @ 3 @ 1

Manual operation is always possible. You can control the blind manually as follows: Button Function Actuation

Blind UP (bright) Brief press of the button: - The blind travels to the top end position - A renewed brief press of the button stops the blind immediately. Long button press: - The blind travels up as long as the button is pressed.

Blind DOWN (dark) Brief press of the button: - The blind travels to the bottom end position - A renewed brief press of the button stops the blind immediately. Long button press: - The blind travels down as long as the button is pressed.

Pos: 30 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Steuer modul e - Online-Dokumentation (--> Für alle Dokumente <--)/++++++++++++ Seitenumbruch ++++++++++++ @ 9\mod_1268898668093_0.docx @ 52149 @ 322 @ 1




Pos: 31 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/2. Ebene/A - F /Displ ay und Symbol e @ 25\mod_1340698574878_15.docx @ 220111 @ 2222 @ 1

5.4 Display and icons Pos : 32 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Displ ay - 6456 Jalousi e @ 26\mod_1343803719301_15.docx @ 226311 @ 3 @ 1

Fig. 3: Symbols No. Function 1 “Automatic” operating mode

2 “Manual” operating mode

3 Operating mode “holiday”

4 Mains power failure

5 Info line / date

6 Venetian blind control UP/DOWN

7 Current weekday

8 Time

Note If the text is too long for the info line, it will run through the info line.





Pos: 34 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/2. Ebene/U - Z/Ü bersicht der M enüstr uktur @ 28\mod_1346940971928_15.docx @ 231074 @ 2222 @ 1

5.5 Overview of the menu structure Pos : 35 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/M enüs truktur 6456 Jal ousi e @ 33\mod_1359470885183_15.docx @ 264507 @ 333 @ 1

Menu Menu items Indicators Setting (function)

Language

Country

Select country (language setting).

Switching times

Block

Set switching times for moving the blind up or down. The same times are taken over for the days from Monday to Friday.

Mon-Fri UP

Mon–Fri Down

Set switching times for moving the blind up or down. The same times are taken over for Saturday and Sunday.

Sat-Sun Up

Sat-Sun Down

Astro

Set a time shift of ±90 minutes. The astro switching times are pre-programmed; however, with the shift the switching time can be adapted to the regional conditions.

Mon-Fri UP

Time shift

Mon–Fri Down

Time shift

Sat-Sun Up

Time shift

Sat-Sun Down

Time shift

Individual

Set the switching times for moving the blind up or down for each weekday independent of each other.

Mon UP

Mon Down Tue Up Tue Down : Date / Time

Day / Month / Year

Set date.

Hours / Minutes Set time.

Special

functions

Set blocking time, to limit the set astro times. Astro blocking time UP: "not rather UP than ...". Astro blocking time DOWN: "not rather DOWN than ...".

Astro --:--





Pos: 37 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/2. Ebene/G - L/Ger äteei nstellungen @ 18\mod_1302768847744_15.docx @ 103548 @ 33222 @ 1

5.6 Adjusting the device Pos : 38 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Geräteeins tellungen Hi nweis 6455_6456_1098 @ 26\mod_1343377008365_15.docx @ 225691 @ 333 @ 1

All settings of the device are carried out supported by text-controlled operator prompting. The language, time and date have to be set first during initial commissioning..

Note Values which need to be changed flash and are displayed in grey in the following illustrated examples.

Pos: 39 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Steuer modul e - Online-Dokumentation (--> Für alle Dokumente <--)/++++++++++++ 1 Leerzeil e Abs tand ++++++++++++ @ 24\mod_1337929289045_0.docx @ 213673 @ 33 @ 1

Pos: 40 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/3. Ebene/S - T /Sprache auswählen @ 28\mod_1346941238305_15.docx @ 231187 @ 3333 @ 1

5.6.1 Selecting languages Pos : 41 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Einstellungen Sprache - 6455_6456 @ 26\mod_1343377850120_15.docx @ 225705 @ 332 @ 1

The language is set via the country selection and the astro time is automatically assigned. The current location (country) of the timer must be selected because of the different time zones.

Note The astro function daily adjusts the switching times automatically to the yearly process of sunrise and sunset.

Fig. 4: Country / language selection

Button Indication Entry / Comments

Germany Selecting languages - Select the country via the arrow buttons.

- Confirm your selection with the OK button. You simultaneously switch to the next menu item. This is followed by setting the year,

month, day, hour and minute. See section 5.6.2.

Note To change the language at a later point in time the device settings must be reset via the reset function. See section 5.6.3.





Pos: 43 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/3. Ebene/A - F /Datum und Uhrzeit ei nstellen @ 28\mod_1347000521439_15.docx @ 231876 @ 333333 @ 1

5.6.2 Setting date and time Pos : 44 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Einstellungen Datum/Uhrzeit - 6455_6456 @ 26\mod_1343378823018_15.docx @ 225719 @ 2 @ 1

Fig. 5: Setting the date and time Sequence of operating steps The first two steps need only be carried out if the date and time are to be changed later. During initial commissioning you will be asked to enter the year directly after selecting the language.

Button Indication Entry / Comments

Switching times - Press the menu button to switch to the setting mode.

Date-Time - Select menu "Date - Time" via the arrow buttons.

Year / --:-- - Confirm your selection with the OK button. The preset year flashes.

2011 – Set the year via the arrow buttons.

Month / --:--

- Confirm your entry with the "OK" button. You simultaneously switch to the next menu item "Month". The preset month flashes.

6.01 - Set the month via the arrow buttons.

Day / --:--

- Confirm your entry with the "OK" button. You simultaneously switch to the next menu item "Day". The preset day flashes.

6.01 - Set the day via the arrow buttons.

Hour / --:--

- Confirm your entry with the "OK" button. You simultaneously switch to the next menu item "Hour". The preset hour flashes.

10:31 - Set the hour via the arrow buttons.

Minute / --:--

- Confirm your entry with the "OK" button. You simultaneously switch to the next menu item "Minute". The preset minute flashes.

10:31 - Set the minutes via the arrow buttons.

- Confirm your entry with the "OK" button. The timer changes into the operating mode.

Note Pressing the menu button switches from setting mode to operating mode. All entries that were confirmed previously with the OK button are taken over.





Pos: 46 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/R ücksetzen des Ger ätes - 6455_6456 @ 26\mod_1343199854442_15.docx @ 225333 @ 222 @ 1

5.6.3 RESET (resetting the device) Pos : 36 /#Neustr uktur#/Online-Dokumentati on/Bedienung/Temperaturregl er/Rücksetzen des Ger ätes - 1098_6455 @ 26\mod_1343199854442_1.docx @ 225331 @ 111111111111111111111111111111111111111111111111111111111111111112221212212221112212211111121221112212222121111222112111222221132121112212221221111111122222222222222222222222222222221 @ 4

Fig. 6: Reset 1. Remove the cover and press the reset button. 2. Replace the cover. 3. Then, again set the language, the date and the time, see section 5.6.

Note After a reset the settings of the language, date and time are deleted. The set switching times remain saved.





Pos: 48 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/2. Ebene/A - F /Betriebsarten @ 13\mod_1286276050737_15.docx @ 91535 @ 333 @ 1

5.7 Operating modes Pos : 49 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Betriebsarten - 6456 @ 26\mod_1343812903649_15.docx @ 226333 @ 2 @ 1

AUTO MANUAL HOLIDAY Fig. 7: Display views of operating modes Icon Operation mode

MANUAL MODE Control is executed only manually. For operation compare operating manual for 6418 U. The user can always switch to manual mode and back. Automatic switching times, as well as brightness and twilight functions are not carried out.

General actuation You can control the blind as follows: UP / : - Touching the top surface The blind travels to the top end position or - Hold the top surface The blind travels up as long as the button is pressed. DOWN / : - Touch the bottom surface - The blind travels to the bottom end position or - Hold the bottom surface The blind travels down as long as the button is pressed. A brief actuation while the blind travels will stop it immediately.

AUTOMATIC MODE The programmed switching times will be executed automatically.

HOLIDAY MODE Control is executed as in automatic mode. A random generator shifts the switching times by up to 30 minutes.

• Press the OK button to change the operating mode. Manual operation is always possible. Pos: 50 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Steuer modul e - Online-Dokumentation (--> Für alle Dokumente <--)/++++++++++++ Seitenumbruch ++++++++++++ @ 9\mod_1268898668093_0.docx @ 52149 @ 123 @ 1




Pos: 51 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/3. Ebene/S - T /Schaltzeiten l öschen @ 26\mod_1343388128693_15.docx @ 225775 @ 211121 @ 1

5.7.1 Deleting switching times Pos : 52 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Schal tzei ten l öschen - 6455_6456 @ 26\mod_1343388058618_15.docx @ 225761 @ 31 @ 1

To be able to delete the switching times during an incorrect entry, the procedure is described here first. For setting the switching times, please continue reading on the next page. Deleting all switching times

Fig. 8: Delete function 1. Press all 4 buttons simultaneously, or the entire operating surface for more than 5 seconds. 2. Confirm the enquiry with the OK button. All set switching times will now be deleted. The date, time and language settings remain saved. Deleting the current switching time in the setting mode

Fig. 9: Delete function of current value Individual values can be deleted if "Setting mode / switching times" has been selected and the time display flashes. 1. Briefly press both arrow buttons. 2. Confirm the enquiry with the OK button. Only the current value is deleted. The display shows -: - - . Pos: 53 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Steuer modul e - Online-Dokumentation (--> Für alle Dokumente <--)/++++++++++++ Seitenumbruch ++++++++++++ @ 9\mod_1268898668093_0.docx @ 52149 @ 12 @ 1




Pos: 54 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/2. Ebene/S - T /Schaltzeiten einstellen @ 26\mod_1343392865770_15.docx @ 225802 @ 3121 @ 1

5.8 Setting switching times Pos : 55 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Schal tzei ten eins tell en (Ei nleitung) @ 28\mod_1346999135048_15.docx @ 231603 @ 213 @ 1

The settings of the switching times that are available and how the menu items are called up is described here. A detailed description of the individual functions is contained in the following sub-sections. Pos: 56 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/3. Ebene/A - F /Bl ock-Pr ogrammier ung @ 28\mod_1346999398767_15.docx @ 231616 @ 3222122 @ 1

5.8.1 BLOCK programming Pos : 57 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Block-Pr ogrammi erung (Allgemein) - 6455_6456 @ 26\mod_1343393105543_15.docx @ 225816 @ 322 @ 1

So that the switching times need not be entered again for each individual day, the BLOCK programming function is available. This means that the switching times are entered once for block (Mon - Fri) and once more for block (Sat - Sun).

Note Within each block the same switching times apply to each day. If the switching times for each day are to be set independent from each other, see section "Setting individual switching times".

Pos: 58 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Vorei ngestellte Bl ock- Schaltzeiten - 6455_6456 Jalousie @ 28\mod_1346999467735_15.docx @ 231659 @ 12 @ 1

Preset block switching times:

Mon–Fri OPEN: 07:00 Mon–Fri CLOSE: 20:00 Sat–Sun OPEN: 08:00 Sat–Sun CLOSE: 21:00

If the display is on -:--, this can mean the following: – no time has been set – the memory is not occupied – the function is not active





Pos: 60 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Einstellungen Bl ock- Programmier ung - 6455_6456 Jal ousie @ 28\mod_1346999606310_15.docx @ 231672 @ 11 @ 1

Fig. 10: Menu item – Block Sequence of operating steps

Button Display Entry / Comments


BLOCK - Press the OK button to select menu item "Block".

The weekdays flash. - Press the OK button again.

MON--FRI UP / 7:00 The preset up-time flashes.

7:30 - Set the desired up-time via the arrow buttons. In this example the up-time has been set at 7:30.

MON--FRI down / 20:00

- Confirm your entry with the "OK" button. You simultaneously switch to the next menu item "Mon - Fri DOWN". The preset down-time flashes.

20:30 - Set the desired down-time via the arrow buttons. In this example the down-time has been set at 20:30.

Sat--Sun UP / 08:00 - Press the OK button again. The preset up-time flashes.

08:30 - Set the desired up-time via the arrow buttons. In this example the up-time has been set at 8:30.

Sat--Sun down / 21:00

- Confirm your entry with the "OK" button. You simultaneously switch to the next menu item "Sat - Sun DOWN". The preset down-time flashes.

21:30 - Set the desired down-time time via the arrow buttons. In this example the down-time has been set at 21:30.

Switching times - Confirm your entry with the "OK" button. The switching times have been set.

- Press the menu button to switch to the operating mode.





Pos: 62 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/3. Ebene/A - F /As tro-Funktion @ 28\mod_1346999843259_15.docx @ 231685 @ 2221111111 @ 1

5.8.2 ASTRO function Pos : 63 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Astr o-Funktion (Ei nleitung) - 6455 @ 28\mod_1346999920136_15.docx @ 231698 @ 12122 @ 1

By activating the astro function the switching times are automatically adjusted each day to the yearly process of sunrise and sunset. The astro switching times are designed as blocks for Mon-Fri and Sat-Sun. Also the entry of a time shift (±90 minutes) is possible in addition to the astro time. With the time shift the astro time can be adapted to the regional conditions. Pos: 64 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Einstellungen Astro-Funktion - 6455_6456 Jal ousie @ 28\mod_1347000021333_15.docx @ 231791 @ 2221 @ 1

Fig. 11: Menu item – Astro Sequence of operating steps



BLOCK - Press the OK button. Menu item "Block" is displayed.

Astro - Select menu item "Astro" via the arrow buttons.

MON--FRI UP / --:--

- Press the OK button. You simultaneously switch to the next menu item "Mon - Fri UP". The display flashes.

MON--FRI UP / 8:24 - Press one of the arrow buttons. The up-time flashes. The astro time for sunrise is fixed and cannot be changed.

Time shift - Confirm the time with the "OK" button. You simultaneously switch to the next menu item "Time shift".




Continuation: Sequence of operating steps Button Display Entry / Comments

0:20

- Set the time shift for the specified astro time via the arrow buttons, so that the switching time is adapted to the regional conditions.

In this example the up-time has been pushed back 20 minutes. No shift will be set if a flashing display -:-- is confirmed.

MON--FRI Down / --:--

- Confirm your entry with the "OK" button. You simultaneously switch to the next menu item "Mon - Fri DOWN". The display flashes.

MO--FR AB / 16:28 - Press one of the arrow buttons. The down-time flashes. The astro time for sundown is fixed and cannot be changed.


0:20


In this example the down-time has been pushed back 20 minutes. No shift will be set if a flashing display -:-- is confirmed.

0:20 - Confirm your entry with the "OK" button. You simultaneously switch to the next menu item "Sat - Sun UP".

Sat--Sun UP / 8:24 - Press one of the arrow buttons. The up-time flashes. The astro time for sunrise is fixed and cannot be changed.


0:20


In this example the up-time has been pushed back 20 minutes. No shift will be set if a flashing display -:-- is confirmed.

0:20 - Confirm your entry with the "OK" button. You simultaneously switch to the next menu item "Sat - Sun DOWN".

Sat--Sun Down / --:-- The display flashes.

Sat--Sun DOWN / 16:28 - Press one of the arrow buttons. The down-time flashes. The astro time for sundown is fixed and cannot be changed.


0:20


In this example the down-time has been pushed back 20 minutes. No shift will be set if a flashing display -:-- is confirmed.







Pos: 66 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/3. Ebene/G - L/Indi viduell e Schaltzeiten @ 28\mod_1347000174088_15.docx @ 231804 @ 2122222222 @ 1

5.8.3 Individual switching times Pos : 67 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Einstellungen Indi vi duelle Schaltzeiten - 6455_6456 Jal ousie @ 28\mod_1347000228517_15.docx @ 231817 @ 22 @ 1

The times for moving up and down for each day can be set independent of each other via menu item "Individual".

Fig. 12: Menu item – Individual Sequence of operating steps



BLOCK - Press the OK button. Menu item "Block" is displayed.

Individual - Select menu item "Individual" via the arrow buttons.

MONday UP / -:--

- Press the OK button. You simultaneously switch to the next menu item "Monday UP". The display flashes.

MONday UP / 7:00 - Press one of the arrow buttons. The suggested up-time flashes.

7:20

- Change the time via the arrow buttons. In this example the up-time has been set at 7:20. No switching time will be set if the flashing display -:-- is confirmed.

MONday Down / -:--

- Confirm your entry with the "OK" button. You simultaneously switch to the next menu item "Monday DOWN". The display flashes.

MONday Down / 20:00 - Press one of the arrow buttons. The suggested down-time flashes.

20:20

- Change the time via the arrow buttons. In this example the down-time has been set at 20:20. No switching time will be set if the flashing display -:-- is confirmed.

Tuesday UP / 7:00

- Confirm your entry with the "OK" button. You simultaneously switch to the next weekday. If desired, use the same procedure for

every further weekday.







Pos: 69 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/2. Ebene/S - T /Sonderfunktionen aufrufen @ 28\mod_1347000678094_15.docx @ 231952 @ 22222 @ 1

5.9 Calling up special functions Pos : 70 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Sonderfunkti onen aufrufen (Ei nleitung) - 6455-1098 @ 28\mod_1347000761227_15.docx @ 231965 @ @ 1

The settings of the special functions that are available and how the menu items are called up is described here. A detailed description of the individual functions is contained in the following sub-sections. Pos: 71 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Steuer modul e - Online-Dokumentation (--> Für alle Dokumente <--)/++++++++++++ 1 Leerzeil e Abs tand ++++++++++++ @ 24\mod_1337929289045_0.docx @ 213673 @ 3 @ 1

Pos: 72 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/3. Ebene/A - F /As tro-Sperrzeit @ 28\mod_1347002725649_15.docx @ 232164 @ 3 @ 1

5.9.1 ASTRO blocking time Pos : 73 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Bedi enung/Ti mer/Einstellungen - Sonderfunktionen - As tro-Sperrzeit - 6455_6456 Jal ousie @ 26\mod_1343816103336_15.docx @ 226470 @ 1 @ 1

The set switching times of the astro function can be limited with the "Astro blockage time" function.

ASTRO blocking time Meaning UP Not earlier UP than ... o'clock

DOWN Not earlier DOWN than ... o'clock

Fig. 13: Menu item – Astro blocking time Sequence of operating steps



Special functions - Select menu "Special functions" via the arrow buttons.

Additional switching

times

- Press the OK button. Menu item "Additional switching times" is displayed.

Astro - Select menu "Astro" via the arrow buttons.

Astro

Blocking time Up

-:--

- Confirm your selection with the OK button. You simultaneously switch to the next menu item "Astro blocking time UP". The display flashes.

6:00 - Set the earliest time via the arrow buttons from which the blind is to be moved up. In this example the preset time of 6:00 has been taken over.

Astro

Blocking time Down

-:--

- Confirm your selection with the OK button. You simultaneously switch to the next menu item "Astro blocking time DOWN". The display flashes.

21:00 - Set the earliest time via the arrow buttons from which the blind is to be moved down. In this example the preset time of 21:00 has been taken over.

Special functions - Confirm your entry with the "OK" button. You simultaneously switch to menu "Special functions".




Busch-Timer® Technical data


Pos: 75 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/1. Ebene/S - T /Technische Daten @ 11\mod_1279185386320_15.docx @ 83019 @ 1 @ 1

6 Technical data Pos: 76 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Technische Daten/Ti mer/Technische Daten 6455_6456 @ 26\mod_1343660576925_15.docx @ 226154 @ 21 @ 1

General Power reserve 4 h

Protection type IP 20

Ambient temperature 0 ... 35°C



Busch-Timer® Mounting / Installation


Pos: 78 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Überschriften (--> Für all e D okumente <--)/1. Ebene/M - O/M ontage /M ontage / Installation @ 18\mod_1302613966111_15.docx @ 103373 @ 12211 @ 1

7 Mounting / Installation Pos: 79 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Sicherheitshinweise und Hinweise (--> Für alle Dokumente <--)/Warnhinweise/Sicherheit - 230 V @ 18\mod_1302606816750_15.docx @ 103308 @ 2222 @ 1

Warning Electric voltage! Risk of death and fire due to electrical voltage of 230 V. – Work on the 230V supply system may only be performed by authorised electricians! – Disconnect the mains power supply prior to installation and/or disassembly!

Pos: 80 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Sicherheitshinweise und Hinweise (--> Für alle Dokumente <--)/Hinweise - Allgemei n/Hi nweis zum el ektrischen Anschluss (Bedi enel ement) @ 28\mod_1347265033624_15.docx @ 232456 @ 12222 @ 1

Notes on electrical connection Prerequisite for mounting or attaching the control element is that the flush-mounted insert has been installed and electrically connected beforehand. The electrical connection is described in the separate instructions of the flush-mounted insert.

Pos: 81 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Montage/Ti mer/M ontage 6455_6456 @ 26\mod_1343717080218_15.docx @ 226218 @ 1 @ 1

1. Pull the attachment off. – If the device is already mounted or assembled, pull off

the attachment from the flush-mounted insert with the aid of the frame.

Fig. 14: Wall mounting: Pulling the attachment off

– If the state of the device is at the point of delivery, pull

off the attachment from the flush-mounted insert with your hands.

– Pull the attachment off only with your hands. Do not lever parts off with screwdrivers or similar hard

objects. This damages the device. – When pulling off, first the resistance of the plastic

clamps must be overcome.

Fig. 15: State of the device at the point of delivery:

pulling off the attachment 2. Plug the attachment together with the frame onto the

flush-mounted insert. – Make sure that the plug-in connection on the rear side

does not get jammed. – If mounting is difficult, check whether a burr has

formed at the lock-in opening of the flush-mounted insert and remove it.

The device is now mounted.

Fig. 16: Plug-on of attachment

=== Ende der Liste für Textmar ke Content ===


Busch-Timer®

1473

-1-8

298

| R

ev. 0

1 |

17.

12.2

012

Pos : 83 /#Neustr uktur#/Online-Dokumentati on (+KN X)/Rücksei ten (--> Für alle Dokumente <--)/Rückseite - Busch-Jaeger - Allgemei n (2013- 01- 03 09:23:43) @ 28\mod_1347009779995_15.docx @ 232282 @ @ 1

A member of the ABB Group Busch-Jaeger Elektro GmbH PO box 58505 Lüdenscheid Freisenbergstraße 2 58513 Lüdenscheid Germany www.BUSCH-JAEGER.com [email protected] Central sales service: Phone: +49 (0) 2351 956-1600 Fax: +49 (0) 2351 956-1700

Notice

We reserve the right to at all times make

technical changes as well as changes to the

contents of this document without prior notice.

The detailed specifications agreed to at the time

of ordering apply to all orders. ABB accepts no

responsibility for possible errors or

incompleteness in this document.

We reserve all rights to this document and the

topics and illustrations contained therein. The

document and its contents, or extracts thereof,

must not be reproduced, transmitted or reused by

third parties without prior written consent by ABB.

Copyright© 2012 Busch-Jaeger Elektro GmbH

All rights reserved

=== Ende der Liste für Textmar ke Backcover ===

Date post:	10-Aug-2020
Category:	Documents
Upload:	others
View:	8 times
Download:	0 times

1473-1-8298 17.12.2012 Operating Instructions Busch-Timer ... · 12/17/2012 · Operating...

Documents