1802-20200005 PA1 User Manual ETM770-8

1

ForSupportContact+468252875,[email protected]+61299567377,[email protected]

TopView

Features:• Cat M1 Connectivity

• NB-IoT Connectivity

• 2G (GSM/GPRS) Connectivity

• Standard RS232 9DF serial port

• 3V to 35V power input on RJ12 connector

• 7 x I/O’s on RJ45 connector

• FME M antenna connector

• Sleep Mode for super low power consumption

• User configurable via configuration tool and ETM Web Office

USER GUIDE

ETM770-8 CELLULAR NETWORK MONITORING TOOL

Cat M1/NB-IoT/2G

1802–20180005 Rev PA1, 2020-05-04

2


TABLE OF CONTENTS

Connecting the sim card ...................................................................................................................... 3

Get started scanning a signal with ETM770 ....................................................................................... 4

2G Mode ............................................................................................................................................. 5

3G Mode ............................................................................................................................................. 6

4G Mode ............................................................................................................................................. 6

Additional Settings ............................................................................................................................... 7

Select Radio Band .............................................................................................................................. 7

Select which operator to scan amongst available operators ............................................................... 7

View Current Network Data ................................................................................................................ 8

View last scan ................................................................................................................................... 13

Communication Test ......................................................................................................................... 14

Send Data to Server ......................................................................................................................... 15

Device Data ...................................................................................................................................... 16

Select APN ........................................................................................................................................ 17

Select User/Password for ISP ........................................................................................................... 17

Server Address ................................................................................................................................. 18

Restart Device .................................................................................................................................. 19

3


CONNECTING THE SIM CARD

4


GET STARTED SCANNING A SIGNAL WITH ETM770 1. Insert SIM card as shown in picture above. 2. Insert the charger into the mini USB connector. The battery is charged with 5V. 3. To turn the device on, press the power button for a minimum of 3 seconds. When

the device is turned on and the charger is successfully connected, the screen shall look as follows:

The battery is almost fully charged. The network connection is 8/10 bars. We are connected to a 4G network with the frequency 2600 MHz R means that the device is logged into the home network.

4. Put on chosen antenna. 5. The device will automatically scan the network signal once turning it on. If not,

find your way to the main menu by pressing the up- button several times. Once pressing "Signal Scanning" you will be redirected to the second menu. Press "Scan Signal".

6. Validate your result. The pictures below show a typical scan for a 2G, 3G and 4G connection.

7. By pressing the up button, you will jump to next menu. If you press the up button multiple times you will finial enter the main menu.

8. By pressing the down button multiple times, you will rotate back to the first row in the present menu.

9. By pressing the power button for more than 5 seconds, the device will go into sleep mode.

10. By pressing both the up and the down key for 5 second, the device will restart.

5


I. Scanned network.

II. The device is connected to a 2G band. The channel is 54 and the frequency is

900 MHz

III. Received Signal Strength Indicator (The signal strength including noise and

interference) measured in dBm. The corresponding value is in the parenthesis.

IV. Signal Strength Bar. Measured in dBm.

V. Signal Quality Min and Max values

VI. Empty space

VII. Signal Quality (Weak, Low, Medium, High or Strong)

VIII. Different data rolls in the bottom bar. CH, PLMN, the scanned network and RSSI.

2G Mode

Scan Menu 2G mode

6


I. Scanned network.

II. The device is connected to a 3G band. The channel is 10762 and the frequency is

2100 MHz.

III. Received Signal Code Power (RSCP) is -72 dBm.

IV. Signal Quality Bar.

V. Carrier to Noise Ratio (EC/n0) is -3.5 dB.

VI. Signal Quality Bar.

VII. Signal Quality (Weak, Low, Medium, High or Strong)


I. The device is connected to a NB band. The band is 20 and the frequency is 800 MHz.

II. Reference Signal Received Power (the signal strength without noise and interference)

measured in dBm. The signal is visualized in the signal bar below the data. Also

shows Signal Quality (Weak, Low, Medium, High or Strong)

III. Signal Quality Bar.

IV. Reference Signal Received Quality (how well the signal is coded) measured in dB.

The signal is visualized in the signal bar below the data.

V. Signal Quality Bar.

VI. Signal to Interference plus Noise Ratio (SINR) used to give theoretical upper bounds

on channel capacity (or rate of information transfer)

VII. Signal Quality Bar


Cat M1 Mode

NB-IoT Mode

Scan Menu Cat M1 mode

Scan Menu NB-IoT mode

7


ADDITIONAL SETTINGS With ETM770 it is possible to make several additional settings.

Select Radio Band

1. Starting at the main menu, press "Signal Scanning" 2. Press "Select Radio Band" 3. Select the radio band you want to scan and press OK. By pressing the down

button, more alternatives are visible.

Once the radio band is selected you will automatically be directed back to the Signal scan menu

Select which operator to scan amongst available operators

1. Starting at the main menu, press "Signal Scanning" 2. Press "Select Net Operators" 3. A list of operators is shown. To see which operators are available please see

the numbers on the right of the display. First letter means Operator status and the second letter means Radio Access Technology (RAT). Operator Status: 0: Unknown, 1: Operator available, 2: Current operator, 3: Operator forbidden

1.

2.

3.

1.

2.

3.

Signal Scan Menu Select Radio Band Menu

Main Menu

Signal Scan Menu

Main Menu

Net Operator Menu

8


View Current Network Data

1. Starting at the main menu, press "Signal Scanning" 2. At the Signal Scan menu, select "Current Network Data" 3. The first view will look similar to the following:

I. The channel is 2850 and the frequency is 2600 MHz. II. E-UTRA frequency band: Download bandwidth: Upload bandwidth III. Mobile Country Code (first part of the PLMN code): Mobile Network Code

(second part of the PLMN code) IV. FDD or TDD: Physical Cell ID V. Reference Signal Received Power (RSRP) is -91 dBm. VI. Reference Signal Received Quality (RSRQ) is -7 dB VII. Tracking Area Code: Global Cell ID VIII. The channel is 2850: Public Land Mobile Network (PLMN) is 240007

1.

3.

2.

Main Menu

Signal Scan Menu

Current Network Data

3.

9


4. If you press the down arrow once you will get a picture that looks similar to the

one below: Monitoring Neighbour Cells

I. Number of Neighbour Cells found II. Neighbour Cell 1 III. Neighbour Cell 2 IV. Neighbour Cell 3 V. Neighbour Cell 4 VI. Neighbour Cell 5 VII. Neighbour Cell 6 VIII. Different data rolls in the bottom bar. CH, PLMN, the scanned network and

RSSI. Syntax: 2G: ARFCN1,rs1,dBm1,MCC1,MNC1,NCC1,BCC1,C11,C21,LAC1,cell1 ARFCN2,rs2,dBm2,MCC2,MNC2,NCC2,BCC2,C12,C22,LAC2,cell2 ... ARFCNn,rsn,dBmn,MCCn,MNCn,NCCn,BCCn,C1n,C2n,LACn,celln 3G: UARFCN1,PSC1,EC/n01,RSCP1 UARFCN2,PSC2,EC/n02,RSCP2 ... UARFCNn,PSCn,EC/n0n,RSCPn 4G: EARFCN1,RSRQ1,RSRP1,PCI1 EARFCN2,RSRQ2,RSRP2,PCI2 ... EARFCNn,RSRQn,RSRPn,PCIn

10


5. If you press the down arrow once again you will get the following:

I. SIM status II. Registration status III. “Network provider(EONS):” (Info text string) IV. Network provider

6. Press the down button again and you will have gotten all the network information available:

I. “APN:” (Info text string) II. APN III. Local IP Address IV. Local IP Address 4G/LTE

11


7. Table below shows a brief explanation of the 3G network abbreviations.

ABBREVIATION FULL NAME FURTHER EXPLANATIONS

CHANN CHANNEL Shows the ARFCN (Absolute Frequency Channel Number) of the Radio Band Frequency.

PSC Primary Synchronization Code Describes start and stop time for the time slot that the device has been allocated.

MCC Mobile Country Code The first part of the PLMN code.

MNC Mobile Network Code The second part of the PLMN code.

EC/n0 Carrier to Noise Ratio

LAC Local Area Code

CELL CELL ID Cell identification number

APN Access Point Name This will only be useful information if you have set up an ISP connection.

LIP Local IP This will only be useful information if you have set up an ISP connection.

RSCP Received Signal Code Power Measured in dBm

SQ Signal Quality Quality value for base station selection in dBm

SRxL RX level value for base station selection indBm

12


8. Table below shows a brief explanation of the 4G network abbreviations. ABBREVIATION FULL NAME FURTHER EXPLANATIONS

EARFCN CHANNEL E-UTRA Absolute Radio Frequency Channel Number

Band Frequency Band E-UTRA frequency band

DL DL bandwidth DL bandwidth

UL UL bandwidth UL bandwidth

Mode Duplex Mode TimeDivisionDuplex (TDD) or FrequencyDivisionDuplex (FDD)

MCC Mobile Country Code The first part of the PLMN code.

MNC Mobile Network Code The second part of the PLMN code.

TAC Tracking Area Code

GCID Global Cell ID Global Cell ID

PhyC ID Physical Cell ID Physical Cell ID

SQ Signal Quality Quality value for base station selection in dBm

RSRP Reference Signal Received Power

RSRQ Reference Signal Received Quality

Note: A PLMN is identified by the Mobile Country Code (MCC) and the Mobile Network Code (MNC)

13


View last scan

1. Starting at the main menu, press "Signal Scanning" 2. At the Signal Scan menu, select "Last Scan"

I. Scanned network. II. Referenced Signal Received Power (RSRP) is -91 dBm. III. RSRP Min and Max values in -dBm IV. Referenced Signal Received Quality (RSRQ) is -7dB. V. RSRQ Min and Max values in -dBm VI. Tracking Area Code: Global Cell ID VII. Public Land Mobile Network (PLMN) is 240007: The channel is 2850 VIII. Scanned network.

1.

2.

3.

Signal Scan Menu

Main Menu Last Scan

3.

14


Communication Test

1. Starting at the main menu, press "Communication Test" 2. Press "PING: 8.8.8.8" This is the IP address to the Google server. 3. See PING Result. It shows success or fail. Ping round trip time in ms

(milliseconds) for three tests.

I. “PING Result:” (Info text string) II. PING Reply result III. No of packages Send: No of packages Received IV. 1st package sent to IP address, round trip time in ms V. 2nd package sent to IP address, round trip time in ms VI. 3rd package sent to IP address, round trip time in ms VII. Packet statistic: sent, received, lost, lost in Percent In order to change the PING address, send a SMS with following syntax to the device: ET-IP3=”IP Address”:”Port” Example: ET-IP3=8.8.8.8:80 This will set the PING address to the Google server.

1.

2.

3.

Main Menu

3.

15


Send Data to Server

1. Starting at the main menu, press "Send Data to Server" 2. Press "Send Last Scan" The IP address 54.77.219.177 is the address to ETM

WEB Office server. 3. Connecting ISP and Connecting Server.

I. Display header line 1 II. Display header line 2 III. ISP Connection process Info IV. ISP Connection result V. Server Connection process Info VI. Server Connection result VII. Server Connection process Info VIII. Empty space In order to change the server address, send a SMS with following syntax to the device: ET-IP1=”IP Address”:”Port” Example: ET-IP1=54.77.219.177:7162 This will set the server address to the EWO server.

1.

2.

3.

Main Menu

3.

16


Device Data

1. Starting at the main menu, press "System" 2. Select "Device Data" 3. Device Data

I. SIM card ID number (SCID) II. Device FW ID number III. Device HW number IV. IMEI number V. Empty space VI. Empty space VII. Empty space VIII. Different data rolls in the bottom bar. CH, PLMN, the scanned network and

RSSI

1.

2.

3.

Main Menu Device Data Menu

Device Data

3.

17


Select APN

1. Starting at the main menu, press "System" 2. Press "Select APN" 3. Choose alternative in the menu.

In order to change the APN list, send SMS with following syntax to the device: ETSAPN=“List position”, “APN name” Example: ++ETSAPN=1, m2m.tele2.com ETSAPN=2, maingate.telia.se This will result in the APN list shown figure “APN list” above.

Select User/Password for ISP

1. Starting at the main menu, press "System" 2. Press "Select User/PassW" in order to select username/password for the ISP 3. Select Username in the menu.

In order to change the user/password list, send SMS with following syntax to the device: ETSUP=“List position”, “Username”, “Password” Example: ETSUP=1,username1,internet1 ETSUP=2,username2,internet2

Main Menu

1.

Device Data Menu

2.

APN list

3.

1.

2.

3.


Username Menu

18


Server Address

1. Starting at the main menu, press "System" 2. Press "Server Address" 3. See Server Address

I. Remote IP address 1 II. Remote Port 1 III. Remote IP address 2 IV. Remote Port 2 V. Empty space VI. Empty space VII. Empty space VIII. Different data rolls in the bottom bar. CH, PLMN, the scanned network and

RSSI

1.

2.

3.


Server Address

3.

19


Restart Device

1. Starting at the main menu, press "System" 2. Press "´Restart Device" 3. The ETM770 will restart.

To turn off the device, press power button for 3 seconds.

Note: Pressing both the up and the down key for 5 second can also perform a restart of the device.

ETMMätteknikAB

Ekbacksvägen32,SE-16869Bromma,Sweden

Tel:+46(0)8252875 Fax:+46(0)8801110

Email:[email protected] Web:www.etm.se

ETMPacificPtyLtd

Suite6,273AlfredStreet,NorthSydneyNSW2060,Australia

Tel:+61(0)299567377 Fax:+61(0)299565791

Email:[email protected] Web:www.etmiot.com.au

Main Menu

1.

2.

Device Data Menu

Date post:	22-Nov-2021
Category:	Documents
Upload:	others
View:	1 times
Download:	0 times

1802-20200005 PA1 User Manual ETM770-8

Documents