CEILING PLAN VIEW SCALE 1 / 50 INSTALLATION DETAIL SCALE 1 / 10 INSTALLATION DETAIL SH-0016-1 BILL OF MATERIALS DESCRIPTION STOCK NUMBER QTY ITEM Angle Molding 7800 16 1 12' ID/HD Suprafine Main Beam 7500/7501 76 2 2' Suprafine Cross Tee XL7520 180 3 Suprafine 60 Deg. Cross Tee - 48in MBS XM756048 160 4 Suprafine Perimeter Cross Tee - 48in MBS XM7548 40 5 Suprafine 60 Deg. Right Corner Bracket 75CB60R 342 6 2" Beam End Retaining Clip BERC2 38 7 Cross Tee Adapter Clip XTAC 38 8 Perimeter Angle Clip PAC 76 9 Lyra 9/16" Square Tegular - 60 Deg. 48 in Base Right Rt. Triangle 100007 400 10 12 Gauge Hanger Wire (Qty. = number of min. hanging point locations) 7891 209 11 These drawings show typical conditions which the Armstrong products depicted are installed. They are not a substitute for an architect's or engineer's plan and do not reflect the unique requirements of local building codes, laws, statutes, ordinances, rules and regulations (Legal Requirements) that may be applicable for a particular installation. Armstrong does not warrant, and assumes no liability for the accuracy or completeness of the drawings for a particular installation or their fitness for a particular purpose. The user is advised to consult with a duly licensed architect or engineer in the particular locale of the installation to assure compliance with all legal requirements. Armstrong is not licensed to provide professional architecture or engineering design services. DATE: 10/2/2018 PD DRAWN BY: NJF DESIGNFLEX SH-0016-1 481.000 ( 40' 1" ) 462.000 ( 38' 6" ) EXAMPLE LAYOUT AND BOM SHOWN WITH LYRA PANELS AND SUPRAFINE SUSPENSION SYSTEM PANEL PRODUCT FAMILIES COMPATIBLE WITH THIS LAYOUT: LYRA, CALLA, OPTIMA, AND ULTIMA SUSPENSION SYSTEMS COMPATABLE WITH THIS LAYOUT: SUPRAFINE ID/HD NOTES: THE EXAMPLE LAYOUT AND CORRESPONDING BOM SHOWN ARE MEANT TO BE USED AS REFERENCE POINTS WHEN SPECIFYING A DESIGNFLEX SYSTEM. IF YOU PLAN TO USE THE EXACT LAYOUT SHOWN, OR ANY VARIATION THEREOF, CONSIDER THE FOLLOWING NOTES: 1) DRAWING DETAILS SHOW A CEILING PLAN VIEW WHICH IS FROM A PLENUM POSITION LOOKING DOWN ONTO THE BACKSIDE OF THE CEILING SYSTEM. BOM LISTS DESCRIPTIONS THAT COORDINATE WITH THE DATA PAGES, AND THESE ITEM DESCRIPTIONS ARE BASED ON VIEWING THE FACE OF THE PRODUCTS. 2) ANGLE BRACKETS AND CORNER BRACKETS ARE INSTALLED AT STANDARD 6" OC ROUTE HOLE INCREMENTS ALONG THE MAIN BEAMS - ALL MAIN BEAMS ARE INSTALLED WITH ALIGNED ROUTE HOLES. 3) ANGLE BRACKETS USED WITHIN LAYOUTS HAVE SCREWS, WASHERS, AND NUTS INCLUDED WITH THEM FOR FASTENING TO MAIN BEAMS. IF CORNER BRACKETS ARE USED IN THE SYSTEM THEY WILL REQUIRE SCREWS THAT ARE NOT INCLUDED AND NEED TO BE SUPPLIED BY OTHERS. 4) SCREWS, RIVETS, AND OTHER GENERAL FASTENERS THAT ARE NOT INCLUDED IN BOM OR IN DETAILS BELOW, NEED TO BE SUPPLIED BY OTHERS. REFER TO INSTALLATION INSTRUCTIONS FOR DETAILS ON REQUIRED FASTENERS. 5) HANGER WIRE LOCATIONS SHOWN BELOW ARE ONLY SUGGESTIONS BASED ON EXAMPLE LAYOUT AND CAN BE MOVED IN ACCORDANCE WITH FOLLOWING REQUIREMENT - HANGER WIRES ARE REQUIRED ALONG MAINS WITHIN 24" OF THE WALL AND NO MORE THAN 48" O.C THEREAFTER. 6) CONDITIONS SHOWN ARE FOR NON-SEISMIC INSTALLATIONS (SEISMIC DESIGN CATEGORY A,B) - REFERENCE INSTALLATION INSTRUCTIONS FOR CONSIDERATIONS AND REQUIREMENTS FOR SEISMIC INSTALLATIONS. 7) DETAILS BELOW AND BOM ARE SUBJECT TO CHANGES AT THE PERIMETER BASED ON THE LAYOUT (LINEAR FEET OF PERIMETER, FULL SIZE VS. CUT PANELS, BORDER PANEL INSTALLATION METHOD). 8) 7800 WALL ANGLE PERIMETER SHOWN BELOW. REFERENCE INSTALLATION INSTRUCTIONS FOR DETAILS ON ALTERNATIVE PERIMETER SOLUTIONS. 9) BOM DOES NOT ACCOUNT FOR THE USE OF SCRAP OR EXCESS MATERIAL CUT FROM OTHER ITEMS. 10) REFER TO MASTER PARTS SHEET, PANEL SHEET, AND INSTALLATION INSTRUCTIONS ILLUSTRATIONS SHEET FOR SPECIFIC DETAIL VIEWS AND DIAGRAMS OF ALL PARTS AND PIECES LISTED IN BOM. SIDE A - REPRESENTS A BORDER CONDITION UTILIZING A SINGLE GRID MEMBER CONNECTION TO THE PERIMETER SIDE B - REPRESENTS A BORDER CONDITION UTILIZING A SINGLE GRID MEMBER CONNECTION OR MULTIPLE GRID MEMBER CONNECTIONS TO THE PERIMETER REFERENCE INSTALLATION INSTRUCTIONS FOR FURTHER DETAILS ON HOW THESE BORDER CONDITIONS ARE INSTALLED 48.594 48.000 15.000 24.000 MAIN BEAMS O.C 48.000 HANGER WIRE O.C 24.000 HANGER WIRE O.C 1 2 9 8 5 3 6 4 7 10 11 PERIMETER CUT PANELS AND CROSS TEES SIDE A SIDE B
Transcript
CEILING PLAN VIEW
SCALE 1 / 50
INSTALLATION DETAIL
SCALE 1 / 10
INSTALLATION DETAIL
SH-0016-1 BILL OF MATERIALS
DESCRIPTIONSTOCK NUMBERQTYITEM
Angle Molding7800161
12' ID/HD Suprafine Main Beam7500/7501762
2' Suprafine Cross TeeXL75201803
Suprafine 60 Deg. Cross Tee - 48in MBSXM7560481604
Suprafine Perimeter Cross Tee - 48in MBSXM7548405
Suprafine 60 Deg. Right Corner Bracket75CB60R3426
2" Beam End Retaining ClipBERC2387
Cross Tee Adapter ClipXTAC388
Perimeter Angle ClipPAC769
Lyra 9/16" Square Tegular - 60 Deg. 48 in Base Right Rt. Triangle10000740010
12 Gauge Hanger Wire (Qty. = number of min. hanging point locations)789120911
These drawings show typical conditions which the Armstrong products depicted are installed. They are not a substitute for an architect's or engineer's plan and do not reflect the unique requirements of local building codes, laws, statutes, ordinances, rules and
regulations (Legal Requirements) that may be applicable for a particular installation. Armstrong does not warrant, and assumes no liability for the accuracy or completeness of the drawings for a particular installation or their fitness for a particular purpose. The user
is advised to consult with a duly licensed architect or engineer in the particular locale of the installation to assure compliance with all legal requirements. Armstrong is not licensed to provide professional architecture or engineering design services.
DATE: 10/2/2018PDDRAWN BY: NJF
DESIGNFLEX SH-0016-1
481.000(
40' 1"
)
462.000(
38' 6"
)
EXAMPLE LAYOUT AND BOM SHOWN WITH LYRA PANELS AND SUPRAFINE SUSPENSION SYSTEM PANEL PRODUCT FAMILIES COMPATIBLE WITH THIS LAYOUT: LYRA, CALLA, OPTIMA, AND ULTIMA SUSPENSION SYSTEMS COMPATABLE WITH THIS LAYOUT: SUPRAFINE ID/HD
NOTES:THE EXAMPLE LAYOUT AND CORRESPONDING BOM SHOWN ARE MEANT TO BE USED AS REFERENCE POINTS WHEN SPECIFYING A DESIGNFLEX SYSTEM. IF YOU PLAN TO USE THE EXACT LAYOUT SHOWN, OR ANY VARIATION THEREOF, CONSIDER THE FOLLOWING NOTES: 1) DRAWING DETAILS SHOW A CEILING PLAN VIEW WHICH IS FROM A PLENUM POSITION LOOKING DOWN ONTO THE BACKSIDE OF THE CEILING SYSTEM. BOM LISTS DESCRIPTIONS THAT COORDINATE WITH THE DATA PAGES, AND THESE ITEM DESCRIPTIONS ARE BASED ON VIEWING THE FACE OF THE PRODUCTS. 2) ANGLE BRACKETS AND CORNER BRACKETS ARE INSTALLED AT STANDARD 6" OC ROUTE HOLE INCREMENTS ALONG THE MAIN BEAMS - ALL MAIN BEAMS ARE INSTALLED WITH ALIGNED ROUTE HOLES. 3) ANGLE BRACKETS USED WITHIN LAYOUTS HAVE SCREWS, WASHERS, AND NUTS INCLUDED WITH THEM FOR FASTENING TO MAIN BEAMS. IF CORNER BRACKETS ARE USED IN THE SYSTEM THEY WILL REQUIRE SCREWS THAT ARE NOT INCLUDED AND NEED TO BE SUPPLIED BY OTHERS. 4) SCREWS, RIVETS, AND OTHER GENERAL FASTENERS THAT ARE NOT INCLUDED IN BOM OR IN DETAILS BELOW, NEED TO BE SUPPLIED BY OTHERS. REFER TO INSTALLATION INSTRUCTIONS FOR DETAILS ON REQUIRED FASTENERS. 5) HANGER WIRE LOCATIONS SHOWN BELOW ARE ONLY SUGGESTIONS BASED ON EXAMPLE LAYOUT AND CAN BE MOVED IN ACCORDANCE WITH FOLLOWING REQUIREMENT - HANGER WIRES ARE REQUIRED ALONG MAINS WITHIN 24" OF THE WALL AND NO MORE THAN 48" O.C THEREAFTER. 6) CONDITIONS SHOWN ARE FOR NON-SEISMIC INSTALLATIONS (SEISMIC DESIGN CATEGORY A,B) - REFERENCE INSTALLATION INSTRUCTIONS FOR CONSIDERATIONS AND REQUIREMENTS FOR SEISMIC INSTALLATIONS. 7) DETAILS BELOW AND BOM ARE SUBJECT TO CHANGES AT THE PERIMETER BASED ON THE LAYOUT (LINEAR FEET OF PERIMETER, FULL SIZE VS. CUT PANELS, BORDER PANEL INSTALLATION METHOD). 8) 7800 WALL ANGLE PERIMETER SHOWN BELOW. REFERENCE INSTALLATION INSTRUCTIONS FOR DETAILS ON ALTERNATIVE PERIMETER SOLUTIONS. 9) BOM DOES NOT ACCOUNT FOR THE USE OF SCRAP OR EXCESS MATERIAL CUT FROM OTHER ITEMS. 10) REFER TO MASTER PARTS SHEET, PANEL SHEET, AND INSTALLATION INSTRUCTIONS ILLUSTRATIONS SHEET FOR SPECIFIC DETAIL VIEWS AND DIAGRAMS OF ALL PARTS AND PIECES LISTED IN BOM.
SIDE A - REPRESENTS A BORDER CONDITION UTILIZING A SINGLE
GRID MEMBER CONNECTION TO THE PERIMETER
SIDE B - REPRESENTS A BORDER CONDITION UTILIZING A SINGLE
GRID MEMBER CONNECTION OR MULTIPLE GRID MEMBER
CONNECTIONS TO THE PERIMETER
REFERENCE INSTALLATION INSTRUCTIONS FOR FURTHER DETAILS
ON HOW THESE BORDER CONDITIONS ARE INSTALLED
48.59448.000
15.000
24.000
MAIN BEAMS
O.C
48.000HANGER WIRE O.C
24.000
HANGER WIRE
O.C
1
2
9
8
5
3
6
47
10
11
PERIMETER CUT PANELS
AND CROSS TEES
SIDE A
SIDE B
BP73AB45L Prelude
BP75AB45L Suprafine
45° Left Angle Bracket
BP73AB45R Prelude
BP75AB45R Suprafine
45° Right Angle Bracket
BP73AB60L Prelude
BP75AB60L Suprafine
60° Left Angle Bracket
BP73AB75L Prelude
BP75AB75L Suprafine
75° Left Angle Bracket
BP73AB45D Prelude
BP75AB45D Suprafine
45° Double Angle Bracket
BP73AB60D Prelude
BP75AB60D Suprafine
60° Double Angle Bracket
BP73AB60R Prelude
BP75AB60R Suprafine
60° Right Angle Bracket
BP73AB75D Prelude
BP75AB75D Suprafine
75° Double Angle Bracket
BP73AB75R Prelude
BP75AB75R Suprafine
75° Right Angle Bracket
BP73CB45 Prelude
BP75CB45 Suprafine
45° Corner Bracket
BP73CB60L Prelude
BP75CB60L Suprafine
60° Left Corner Bracket
BP73CB60R Prelude
BP75CB60R Suprafine
60° Right Corner Bracket
BPXM734524 Prelude
BPXM754524 Suprafine
45° Cross Tee - 24" MBS
SCALE 1 / 4
BPXM736024 Prelude
BPXM756024 Suprafine
60° Cross Tee - 24" MBS
SCALE 1 / 4
BPXM737524 Prelude
BPXM757524 Suprafine
75° Cross Tee - 24" MBS
SCALE 1 / 4
BPXM734548 Prelude
BPXM754548 Suprafine
45° Cross Tee - 48" MBS
SCALE 1 / 4
BPXM736048 Prelude
BPXM756048 Suprafine
60° Cross Tee - 48" MBS
SCALE 1 / 4
BPXM737548 Prelude
BPXM757548 Suprafine
75° Cross Tee - 48" MBS
SCALE 1 / 4
BPXM7324 Prelude
BPXM7524 Suprafine
Perimeter Cross Tee - 24" MBS
SCALE 1 / 4
BPXM7348 Prelude
BPXM7548 Suprafine
Perimeter Cross Tee - 48" MBS
SCALE 1 / 4
BPPCC
Axiom Perimeter Corner Clip
SCALE 1 / 2
BPPAC
Perimeter Angle Clip
SCALE 1 / 2
DATE:
SCALE:
DRAW
N BY:
PRO
JECT:
These draw
ings show
typical conditions w
hich the A
rm
strong products depicted are installed. T
hey are not a substitute for an architect's or engineer's plan and
do not reflect the unique requirem
ents of local building codes, law
s, statutes, ordinances, rules and regulations (Legal R
equirem
ents) that m
ay be applicable for
a particular installation. A
rm
strong does not w
arrant, and assum
es no liability for the accuracy or com
pleteness of the draw
ings for a particular installation or
their fitness for a particular purpose. T
he user is advised to consult w
ith a duly licensed architect or engineer in the particular locale of the installation to assure
com
pliance w
ith all legal requirem
ents. A
rm
strong is not licensed to provide professional architecture or engineering design services.
10/2/2018
KAPlace
PD
30.425
22.677
16.923
64.366
49.510
41.661
34.000
68.000
DesignFlex Shapes Com
ponents
-
NJFriez
Highlight
NJFriez
Highlight
NJFriez
Highlight
NJFriez
Highlight
Lyra 9/16" Square Tegular - 75 Deg. 12 in Base Right Parallelogram
100020
Lyra 9/16" Square Tegular - 75 Deg. 12 in Base Left Parallelogram
100021
Lyra 9/16" Square Tegular - 75 Deg. 24 in Base Trapezoid
100012
Lyra 9/16" Square Tegular - 45 Deg. 24 in Base Rt. Triangle
100008
Lyra 9/16" Square Tegular - 60 Deg. 48 in Base Right Rt. Triangle
100007
Lyra 9/16" Square Tegular - 60 Deg. 48 in Base Left Rt. Triangle
100006
Lyra 9/16" Square Tegular - 75 Deg. 24 in Base Triangle
100005
Lyra 9/16" Square Tegular - 60 Deg. 24 in Base Triangle
100002
Lyra 9/16" Square Tegular - 60 Deg. 48 in Base Triangle
100003
Lyra 9/16" Square Tegular - 45 Deg. 48 in Base Triangle
100001
Lyra 9/16" Square Tegular - 75 Deg. 12 in Base Triangle
100004
Lyra 9/16" Square Tegular - 75 Deg. 24 in Base Right Parallelogram
100022
Lyra 9/16" Square Tegular - 60 Deg. 24 in Base Right Parallelogram
100016
Lyra 9/16" Square Tegular - 60 Deg. 48 in Base Right Parallelogram
100018
Lyra 9/16" Square Tegular - 45 Deg. 48 in Base Right Parallelogram
100014
Lyra 9/16" Square Tegular - 75 Deg. 24 in Base Left Parallelogram
100023
Lyra 9/16" Square Tegular - 60 Deg. 24 in Base Left Parallelogram
100017
Lyra 9/16" Square Tegular - 45 Deg. 48 in Base Left Parallelogram
100015
Lyra 9/16" Square Tegular - 60 Deg. 48 in Base Left Parallelogram
100019
Lyra 9/16" Square Tegular - 75 Deg. 48 in Base Trapezoid
100013
Lyra 9/16" Square Tegular - 45 Deg. 96 in Base Trapezoid
100010
Lyra 9/16" Square Tegular - 60 Deg. 48 in Base Trapezoid
100011
Lyra 9/16" Square Tegular - 45 Deg. 48 in Base Rt. Triangle
100009
These drawings show typical conditions which the Armstrong products depicted are installed. They are not a substitute for an architect's or engineer's plan and do not reflect the unique requirements of local building codes, laws, statutes, ordinances, rules and
regulations (Legal Requirements) that may be applicable for a particular installation. Armstrong does not warrant, and assumes no liability for the accuracy or completeness of the drawings for a particular installation or their fitness for a particular purpose. The user
is advised to consult with a duly licensed architect or engineer in the particular locale of the installation to assure compliance with all legal requirements. Armstrong is not licensed to provide professional architecture or engineering design services.
DATE: 4/19/2018PDDRAWN BY: KAP
DesignFlex - Panels Lyra Shapes
24
12
48
24
24
24
48
48
24
48
12
24 24
1224
24
48
4848
24
48
24
24
24
24
24
48
24
48
48
48
48
24
48
24
48
24
96
24
24
24
48
48
24
48
48
NOTES:
1. Views are from the face of the panel, and descriptions are based on these views
2. Dimensions are nominal and reflect grid spacings
3. Scale 1:15
NJFriez
Highlight
Calla 9/16" Square Tegular - 75 Deg. 12 in Base Right Parallelogram
100116
Calla 9/16" Square Tegular - 75 Deg. 12 in Base Left Parallelogram
100117
Calla 9/16" Square Tegular - 75 Deg. 24 in Base Trapezoid
100110
Calla 9/16" Square Tegular - 45 Deg. 24 in Base Rt. Triangle
100107
Calla 9/16" Square Tegular - 60 Deg. 48 in Base Right Rt. Triangle
100106
Calla 9/16" Square Tegular - 60 Deg. 48 in Base Left Rt. Triangle
100105
Calla 9/16" Square Tegular - 75 Deg. 24 in Base Triangle
100104
Calla 9/16" Square Tegular - 60 Deg. 24 in Base Triangle
100101
Calla 9/16" Square Tegular - 60 Deg. 48 in Base Triangle
100102
Calla 9/16" Square Tegular - 45 Deg. 48 in Base Triangle
100100
Calla 9/16" Square Tegular - 75 Deg. 12 in Base Triangle
100103
Calla 9/16" Square Tegular - 75 Deg. 24 in Base Right Parallelogram
100118
Calla 9/16" Square Tegular - 60 Deg. 24 in Base Right Parallelogram
100114
Calla 9/16" Square Tegular - 45 Deg. 48 in Base Right Parallelogram
100112
Calla 9/16" Square Tegular - 75 Deg. 24 in Base Left Parallelogram
100119
Calla 9/16" Square Tegular - 60 Deg. 24 in Base Left Parallelogram
100115
Calla 9/16" Square Tegular - 45 Deg. 48 in Base Left Parallelogram
100113
Calla 9/16" Square Tegular - 75 Deg. 48 in Base Trapezoid
100111
Calla 9/16" Square Tegular - 60 Deg. 48 in Base Trapezoid
100109
Calla 9/16" Square Tegular - 45 Deg. 48 in Base Rt. Triangle
100108
These drawings show typical conditions which the Armstrong products depicted are installed. They are not a substitute for an architect's or engineer's plan and do not reflect the unique requirements of local building codes, laws, statutes, ordinances, rules and
regulations (Legal Requirements) that may be applicable for a particular installation. Armstrong does not warrant, and assumes no liability for the accuracy or completeness of the drawings for a particular installation or their fitness for a particular purpose. The user
is advised to consult with a duly licensed architect or engineer in the particular locale of the installation to assure compliance with all legal requirements. Armstrong is not licensed to provide professional architecture or engineering design services.
DATE: 4/19/2018PDDRAWN BY: KAP
DesignFlex - Panels Calla Shapes
24
12
48
24
24
24
48
48
24
48
12
24
12
24 24
24
24
48 48
24
48
48
NOTES:
1. Views are from the face of the panel, and descriptions are based on these views
2. Dimensions are nominal and reflect grid spacings
3. Scale 1:15
24
24
24
24
24
48
24
48
24
48
48
48
24
24
48
24
24
48
NJFriez
Highlight
Optima 9/16" Square Tegular - 75 Deg. 12 in Base Right Parallelogram
100219
Optima 9/16" Square Tegular - 75 Deg. 12 in Base Left Parallelogram
100220
Optima 9/16" Square Tegular - 75 Deg. 24 in Base Trapezoid
100211
Optima 9/16" Square Tegular - 45 Deg. 24 in Base Rt. Triangle
100207
Optima 9/16" Square Tegular - 60 Deg. 48 in Base Right Rt. Triangle
100206
Optima 9/16" Square Tegular - 60 Deg. 48 in Base Left Rt. Triangle
100205
Optima 9/16" Square Tegular - 75 Deg. 24 in Base Triangle
100204
Optima 15/16" Lay-In - 75 Deg. 24 in Base Triangle
100227
Optima 9/16" Square Tegular - 60 Deg. 24 in Base Triangle
100201
Optima 9/16" Square Tegular - 60 Deg. 48 in Base Triangle
100202
Optima 15/16" Lay-In - 60 Deg. 48 in Base Triangle
100225
Optima 9/16" Square Tegular - 45 Deg. 48 in Base Triangle
100200
Optima 9/16" Square Tegular - 75 Deg. 12 in Base Triangle
100203
Optima 9/16" Square Tegular - 75 Deg. 24 in Base Right Parallelogram
100221
Optima 15/16" Lay-In - 75 Deg. 24 in Base Right Parallelogram
100244
Optima 9/16" Square Tegular - 60 Deg. 24 in Base Right Parallelogram
100215
Optima 9/16" Square Tegular - 60 Deg. 48 in Base Right Parallelogram
100217
Optima 15/16" Lay-In - 60 Deg. 48 in Base Right Parallelogram
100240
Optima 9/16" Square Tegular - 45 Deg. 48 in Base Right Parallelogram
100213
Optima 9/16" Square Tegular - 75 Deg. 24 in Base Left Parallelogram
100222
Optima 15/16" Lay-In - 75 Deg. 24 in Base Left Parallelogram
100245
Optima 9/16" Square Tegular - 60 Deg. 24 in Base Left Parallelogram
100216
Optima 9/16" Square Tegular - 45 Deg. 48 in Base Left Parallelogram
100214
Optima 9/16" Square Tegular - 60 Deg. 48 in Base Left Parallelogram
100218
Optima 15/16" Lay-In - 60 Deg. 48 in Base Left Parallelogram
100241
Optima 9/16" Square Tegular - 75 Deg. 48 in Base Trapezoid
100212
Optima 15/16" Lay-In - 75 Deg. 48 in Base Trapezoid
100235
Optima 9/16" Square Tegular - 45 Deg. 96 in Base Trapezoid
100209
Optima 9/16" Square Tegular - 60 Deg. 48 in Base Trapezoid
100210
Optima 9/16" Square Tegular - 45 Deg. 48 in Base Rt. Triangle
100208
Optima 15/16" Lay-in - 45 Deg. 48 in Base Rt. Triangle
100231
These drawings show typical conditions which the Armstrong products depicted are installed. They are not a substitute for an architect's or engineer's plan and do not reflect the unique requirements of local building codes, laws, statutes, ordinances, rules and
regulations (Legal Requirements) that may be applicable for a particular installation. Armstrong does not warrant, and assumes no liability for the accuracy or completeness of the drawings for a particular installation or their fitness for a particular purpose. The user
is advised to consult with a duly licensed architect or engineer in the particular locale of the installation to assure compliance with all legal requirements. Armstrong is not licensed to provide professional architecture or engineering design services.
DATE: 4/19/2018PDDRAWN BY: KAP
DesignFlex - Panels Optima Shapes
24
12
48
24
24
24
48
48
24
48
12
24 24
1224
24
48
4848
24
48
24
24
24
24
24
48
24
48
48
48
48
24
48
24
48
24
96
24
24
24
48
48
24
48
48
NOTES:
1. Views are from the face of the panel, and descriptions are based on these views
2. Dimensions are nominal and reflect grid spacings
3. Scale 1:15
NJFriez
Highlight
Ultima 9/16" Beveled Tegular - 75 Deg. 12 in Base Right Parallelogram
100315
Ultima 9/16" Beveled Tegular - 75 Deg. 12 in Base Left Parallelogram
100316
Ultima 9/16" Beveled Tegular - 75 Deg. 24 in Base Trapezoid
100310
Ultima 9/16" Beveled Tegular - 45 Deg. 24 in Base Rt. Triangle
100307
Ultima 9/16" Beveled Tegular - 60 Deg. 48 in Base Right Rt. Triangle
100306
Ultima 9/16" Beveled Tegular - 60 Deg. 48 in Base Left Rt. Triangle
100305
Ultima 9/16" Beveled Tegular - 75 Deg. 24 in Base Triangle
100304
Ultima 9/16" Beveled Tegular - 60 Deg. 24 in Base Triangle
100301
Ultima 9/16" Beveled Tegular - 45 Deg. 48 in Base Triangle
100300
Ultima 9/16" Beveled Tegular - 75 Deg. 12 in Base Triangle
100303
Ultima 9/16" Beveled Tegular - 60 Deg. 24 in Base Right Parallelogram
100313
Ultima 9/16" Beveled Tegular - 60 Deg. 24 in Base Left Parallelogram
100314
Ultima 9/16" Beveled Tegular - 60 Deg. 48 in Base Trapezoid
100309
These drawings show typical conditions which the Armstrong products depicted are installed. They are not a substitute for an architect's or engineer's plan and do not reflect the unique requirements of local building codes, laws, statutes, ordinances, rules and
regulations (Legal Requirements) that may be applicable for a particular installation. Armstrong does not warrant, and assumes no liability for the accuracy or completeness of the drawings for a particular installation or their fitness for a particular purpose. The user
is advised to consult with a duly licensed architect or engineer in the particular locale of the installation to assure compliance with all legal requirements. Armstrong is not licensed to provide professional architecture or engineering design services.
DATE: 4/19/2018PDDRAWN BY: KAP
DesignFlex - Panels Ultima Shapes
24
12
48
24
24
24
24
48
12
24 24
12
24
24
24 24
48
24
24
24
24
48
48
24
NOTES:
1. Views are from the face of the panel, and descriptions are based on these views
2. Dimensions are nominal and reflect grid spacings
