BRUNDLE2 LEAF TELESCOPIC SLIDING GATE KIT

This kit is made of galvanized steel components ideal for installation on sliding gates. A steel wire is used to transfer the telescopic motion. A gate with this system can be motorized. The leaves move simultaneously sliding on ground rails and have the advantage of taking less space compared to a single ground track sliding gate when the gate is in the open position. This feature makes the product ideal for sites where space is limited.

DESCRIPTION

S2

S1

COMPONENT LIST

ACCESSORIES

TELESCOPIC TRANSMISSION SET

16mm ROUND GROOVED TRACK

Concrete-in

Code: 05GD616Z3

COUPLING

UPPER GUIDE ROLLER

Code: 05GD118

ADJUSTABLE ROLLER PLATE GUIDE

ROUND GROOVED WHEEL

For 16mm track

Code: 0515060

COVERFor telescopic transmission set

CONNECTION ROLLERS

Gate rollers and track are not included with this kit. See below for additional components.

Page 1 of 6

Ø 35mmM8

M8

M8

60mm

Min. 100mm53mm

23.5mm50mm

15mm99mm

NO

~25mm

~25mm

1 2

3 4

1

3

5

2

4

6

S1

S1

S1

S1

S1

Code: 39TK2004 / 008

Code: 39TK2114

Page 2 of 6

20mm

30mm

100mmS1 S2

1

2

3

C

D

7

9

11

8

10

12

S1

S1

Code: 39TK2004 / 008

Code: 39TK2004 / 008

1 x Code: 39TK2004 / 008

Code: 39TK2114

Code: 39TK2114

2 x Code: 39TK2114

S1

S1

Page 3 of 6

1

3

2

S1S2

100mm

S1S2

L

Safety screwsMax. 10mm

13

15

17

14

16

18

Code: 39TK2004 / 008

Code: 39TK2114

S1

S1

S2

S1

Page 4 of 6

DIMENSIONS TABLE

SECTION DIMENSIONS

B A

S2 S1

C

C

D

L

T

50+TL = [(A+B)/2]+C

(50) mm

Important

CodeA max

(m)C

(m)D min(mm)

S2 max(kg)

39TK2004 4.0 0.3 50 30039TK2008 8.0 0.3 50 30039TK2114 11.4 0.6 70 400

Opening(A) Code L (m)

with B = 0.08

3 39TK2004 1.844 39TK2004 2.345 39TK2008 2.846 39TK2008 3.347 39TK2008 3.848 39TK2008 4.349 39TK2114 5.1410 39TK2114 5.6411 39TK2114 6.14

A = 3.5mB = 0.06m (your choice)C = 0.3m (see table above)L = [(A+B)/2]+CL = [(3.5+0.06)/2]+0.3L = [(3,56)/2]+0.3L = 1.78+0.3L = 2.08

Example of dimensions not in table

Page 5 of 6

May 2019

www.fhbrundle.co.ukTel. 01708 25 35 45 sales@brundle.com

Whilst every effort has been made to ensure the accuracy of the information supplied. F.H.Brundle cannot be held responsible for any errors or omissions. This product must only be employed for its original intended use. Any other use is wrong and potentially dangerous. Installation must be carried out in full compliance with current regulations. F.H.Brundle cannot be held liable for any damages resulting from wrongful, erroneous or negligent use.

Attention: installations that do not comply with the illustrated procedure or failure to carry out correct maintenance operations can cause the gate to derail and endanger the safety of people and property.

To maintain the parts in good and safe working order it is necessary to follow these steps:

1. After gate assembly is completed, perform a few manual open/close cycles to make sure there are no loose parts. Ensure the cable is lubricated along its entire length with supplied oil (pic.10). Check the system every 3 months or after a maximum 8000 cycles to make sure there are no loose parts and that the system is properly lubricated

2. In case of loose cable check all clamps and follow the tensioning procedure3. In case of accidental impact caused by moving vehicles or other external factors, check parts for external damage. If there

is irreparable damage, replace with a new part. Always check the gate by manually performing a few open/close cycles. All maintenance procedures must be performed by trained technicians

4. If the gate has any difficulty of movement or shows abnormal oscillations, the gate must be checked for worn parts which must be replaced if necessary. Gates working in harsh ambient conditions, such as hight humidity, salt, acids, dust or temperatures above 120°C will require special attention and frequent maintenance

1. The installation of safety strikes and safety screws (pic.18) is compulsory2. To select the right automation, it is necessary to calculate the weight of the gate by adding 2 times the weight of the second

leaf S2 to 1 times the weight of the first leaf S1 • Calculate mass = Weight S1 + (2 x Weight S2)

3. Recommended automation: 24V DC4. The ideal traction is one that is just enough to keep the wire stretched. An excessive traction of the wire will shorten its

working life5. Maximum S2 closing speed = 0.18m/s

• Fast and hard start/stops will result in system failure • Accelerations, decelerations and high speed variations could cause an elastic effect between the leaves

MAINTENANCE

TECHNICAL SPECIFICATION

Page 6 of 6