20-1703

Doc. 20-1703 Rev H (12/20/2005) Y Series Elevator Operation Procedure Manual

Y Series Elevator Operating Procedure Manual


1

TABLE OF CONTENTS

Section Page

1 - Introduction 2 1.1 General Information 1.2 Description

2 - Operation 3-4 2.1 Installation 2.2 Operation

3 - Maintenance 5 3.1 Inspection 3.2 Lubricants

4 - Shop Repairs 6-7 4.1 Changing Inserts 4.2 Slip Insertion and Removal 4.3 Elevator Disassembly

Critical Drawing Areas 8

Assembly, Parts Breakdown and Replacement Parts 9-20

Certificate of Warranty and Guarantee to Quality 21


2

1. INTRODUCTION

1.1 GENERAL INFORMATION

This technical manual contains operation and maintenance instructions for Access Oil Tools, Inc. Y Series slip type manual elevators with assembly drawings and complete parts breakdown. It provides for proper field use, disassembly and repair.

1.2 DESCRIPTION

The Y series consists of six models of center latch, slip type elevators featuring a four-slip design. The types HYT, YT, MYT, LYT and HYC handle tubing and drill collars with any type of upset and wall thickness with the simple installation of the proper size sips and slip setting ring. The type YC is a similar elevator for handling either external upset of API collar type casing. In addition, slips can be provided that enables the YC to handle dual string of tubing. All models have a spring loaded latch and latch lock to protect against the possibility of the elevator opening under load.

The Y series includes heavy-duty capacity ratings of the 200-Ton HYC, 150-Ton HYT and the 75-Ton YC and YT. The MYT and LYT are lightweight elevators covering medium depth wells. The LYT is designed to handle macaroni type and other small size tubing from 1.050 to 2-1/16 OD. The model and size range is shown in the following table.

Model Short Ton Metric Ton Range LYT 20 18.14 1.050 2-1/16 MYT 40 36.20 1.315 - 2-7/8 YT 75 68.10 1.315 3-1/2 YC 75 68.10 3-1/2 7 HYT 150 136.20 2-3/8 3-1/2 HYC 200 18.16 3-1/2 7-5/8

Any overloading of the recommended rating or misuse of this equipment can cause serious injury or death.


3

2. OPERATION

2.1 PREPARATION

In order for the slip type elevator to operate, it is necessary to install the slip setting ring, slip body and inserts corresponding to the size of the tubing being run. To change slip bodies, slip setting rings and inserts, follow the procedures described in section 4, shop repairs - slip insertion and removal and changing inserts.

2.2 INSTALLATION

As with any manual elevator, the slip type elevator is easily installed on the links. After using a tugger line or catline to lift the elevator onto the rig floor and position it next to the rotary table, perform the following procedure:

Remove cotter pin and nut from link block bolt and remove link block bolt.

Lift the bottom of the link block and hook the small end to the link through the link block and link arm.

Lower the link block and re-install the link block bolt, nut and cotter pin.

Repeat this procedure on the other link block.

To remove, simply reverse the installation process.

2.3 OPERATION

The latch and safety latch lock of the slip type elevator locks automatically when the elevator is closed around the pipe. The slips set when the elevator is raised against the tool joint, which pushes down on the slip setting ring. To open the elevator, ensure that there is no load on the elevator and that the slips are not under any load, then simply pull the latch lock handle out and swing the elevator halves apart.

When using a Y series elevator to make-up or break-out a connection, the load on the elevator needs to be released to unset the slips around the tubular. Once the connection is torque up (made-up) or unscrewed (broken-out), the load can be reapplied to the slips so the tubular can be run in the hole or set back as desired.

Pipe Should Not Be Rotated In The Elevator When The Slips Are Set.


4

Caution:

Elevators are manufactured to operate at rated capacity in a vertical direction. When used to pick or lay down a SINGLE JOINT of pipe in a non-vertical position, the operator MUST ensure that the latch, safety latch & latch springs are in good working order. Prior to hoisting with the elevator from any position, it is necessary to ensure that the elevator is completely installed around the pipe and that the latches are properly engaged. Failure to do this could result in serious injury.

If there is any question as to the safe operation condition of an elevator, it must be removed from service until a review can be completed.

Be sure to use the handles provided for opening, closing, and handling the elevator. Keep hands away from all other areas when the elevator is in use.

Make sure all slip segments are free and in the up position when latching the elevator. If any of the segments are stuck in the down position, the elevator may not close properly.

Check the latch lock for full engagement when closed around the pipe. Elevator should only be used on pipe in which the elevator is dressed with the correct

inserts and setting plate, not on any other pipe size. Make sure cotter pins are inserted in the link block bolt. Make sure the elevator and slip bodies are used with the correct size tubular (per API

specification). Oversized pipe could result in the elevator latching partially or not at all. Undersized or oversized pipe could cause uneven stress distribution, inadequate load-bearing area, and possible wedging in the slip setting ring or falling through the elevator.


5

3. MAINTENANCE

Practice safety at all times when servicing the equipment and use approved safety methods, material and tools. Always wear protective gear for eyes, head and hands.

3.1 INSPECTION

To insure optimum performance from the Y series slip type elevators, the following checks should be performed once a week:

Check for worn hinge pin, latch pin, latch lock pin, slips and slip pins and their mating parts. These may hinder proper opening and closing of the door, latch and latch lock.

Check slip springs, rubber bushings, inserts and setting plate for wear. Check for proper operation of latch stop mechanism. Latch should not stop against

the body when engaged. Check slip setting ring for spreading and wear in the setting area. Check to make sure that link block bolts are retained w/ nuts and cotter pins.

It is recommended that elevators undergo factory magnetic particle inspection a minimum of once every six months and load test once a year.

3.2 LUBRICANTS

Lubricate the elevator regularly during the usage and storage to prevent corrosion. Use an extreme pressure, multi-purpose, lithium base grease of no. 1 or no. 2 consistency and multi-weight motor oil. When the elevator is in use, lubricate the elevator according to the following schedule:

Daily

Grease hinge pins Lubricate latch pin and latch lock pin Grease underside of lifting arm Grease seating face of slip setting ring Grease back of slips Make sure link bolts have nuts and cotter pins

Weekly

Brush grease on springs Grease link retainer fasteners


6

4. SHOP REPAIRS

4.1 CHANGING INSERTS

Always wear eye protection when removing or replacing inserts to protect against chip fragments.

To replace worn inserts or change sizes:

Remove guide plate, slip setting ring and bushing, and insert retainer plate. Using a brass punch and hammer, drive out the inserts. Clean and grease the insert slots before installing new inserts.

Important: Install the correct size inserts for the tubular used and make sure the teeth are pointing in the up position.

4.2 SLIP INSERTION AND REMOVAL

To insert slip bodies into the elevator, use the following procedure:

1. Open the elevator fully and clean the slip taper and spring pockets. 2. Clean the slips if necessary and grease the taper portion of the slip body. 3. Insert the slip springs into the spring pocket leaving the inner edge of the spring exposed. 4. Starting on the left side of the elevator and proceeding counter clockwise, insert assembled

slip bodies into the elevator one at a time. Compress the edge of the lip spring with the bottom of the upper pocket.

5. For LYT, insert the slip retaining pin, or (HYC, HYT, YT, MYT, YC) insert the slip retaining bolt through the top of the elevator, slip body lug and into the slip spring. Do not insert the pin or bolt completely through the spring until both pins retain their respective slip body and slip spring.

6. Once both slip pins are in place, (LYT) insert the slip retaining pin into position, or (HYC, HYT, YT, MYT, YC) screw retaining bolts into place.

7. Place an insert retainer plate into each slip. 8. Place the slip setting ring over the slips on the left hand side of the elevator. Attach the setting

ring to the slip segments with rubber bushings, lock-washers and cap screws. (Note: the setting ring must be placed on the left side of the elevator to avoid obstructing the tubing entering the elevator).

9. Secure the insert retainer plates with the short cap screws on the right side of the elevator. 10. Tighten all cap screws. There must be approximately 1/16 inch play between the slip setting

ring and its corresponding insert retainer plate as provided by the bushing. (Important: each set of cap screws retaining the slip setting ring and insert retainer must be secured with lock wire to keep them from backing out. Stainless Steel 3/32 lock wire is recommended).

o To prevent jamming, check each pair of slip bodies for the following: Free movement of slip body guide pin. No interface of slip guide pin lug in spring recess slots. A gap between the slips when they are set and fully compressed.

For slip removal, the top guide plate, slip setting ring, and slip retaining bolt must be removed from the elevator.


7

4.3 Elevator Disassembly

(HYC, YT, YC, MYT, LYT) latch pins are retained by dowel pins that must be removed before driving out latch pin. Drive out latch pin from bottom of elevator.

To remove the latch lock pin on (MYT, HYT, YT), remove dowel pins and drive out latch lock pin. For (YC, YT) remove cotter key and drive out the latch lock pin. On the HYC simply remove the cotter and nut.

Hinge pins on the LYT, MYT, YT, YC, and HYC are pressed fit. To remove, simply drive the hinge pin out from the bottom of the elevator. The hinge and latch pin on the HYT elevator are retained by expansion plugs and lock bar. To remove, drive the pins out from the bottom of the elevator which will knockout the expansion plug and shearing lock bar.

To remove the link block, remove cotter keys from the link block bolts and unscrew link block bolts.

After inspecting all parts for cracks and wear, replace defected parts and reassemble in reverse order of disassembly.

Because HYC, YT, YC, MYT, and LYT hinge pins are pressed fit, they must be replaced with new ones once they are removed from the elevator. Failure to replace the original hinge pin once it is removed may cause it to walkout or fallout of the elevator during use and cause severe injury.

4.4 ACCESS OIL TOOLS, INC. FACTORY TOOL REPAIR.

Worn elevators are returned to high quality condition with precision factory repair procedures. When tools are received for repairs, they are dismantled and checked for dimensional accuracy and undergo magnetic particle inspection. Worn areas are repaired by welding or replacing with new parts and the components are reheat-treated to original hardness specifications. After a second magnetic particle inspection, the tools are reassembled and carefully checked.

Caution Do not use any elevator if the latch and latch lock do not function properly. Use only parts manufactured and sold by Access Oil Tools, Inc. or authorized agents. Re-machining and re-heat treating should be performed only at Access Oil Tools, Inc.

manufacturing facility or by an authorized repair agent. Improper machining could result in increased stress (decreased load carrying capability) or improper alignment of component parts. Either condition could be hazardous to personnel and equipment.

Due to the complex metallurgy found in Access Oil Tools, Inc. materials, welding should be performed only at access oil tools, inc. manufacturing facility or by an authorized repair agent.

Bodies and doors are specifically matched by trained Access Oil Tools, Inc. professionals. For this reason, a body or door from one elevator should never be exchanged with a body or door from another elevator.

Pins retained by riveting or peen must be well secured by upsetting a substantial amount of material on the pin or mating parts.

Always wear gloves and eye protection when grinding, striking or handling parts. Do not use any elevator with wear in hinge pin, latch pin, and latch lock pin areas. Wear in

these areas will cause latch and latch lock to function improperly. Make sure that cotter pins are used on link block bolts.


8

Y SERIES ELEVATOR CRITICAL AREAS


9

REPLACEMENT PARTS FOR LYT SLIP TYPE ELEVATOR

AOT # Item No. Description No. Req. Wt. (lbs.) E28786 1 Insert Retainer Plate 4 .13

E28787 2 Insert Retainer Screw 2 .13 E28785 3 Setting Plate Bolt w/ Washer 2 .25 E339369-13 4 Setting Plate Washer 2 .06 E28760 5 Slip Bolt 4 .25 E28761 6 Slip Spring 4 .15

SETTING PLATES AOT # Item No. Description No. Req. Wt. (lbs.) E28782 7 2-1/16 Setting Plate 1 2.25 E28737 7 2 Setting Plate 1 2.35 E28783 7 1-1/2 (1.900) Setting Plate 1 3.00 E28784 7 1-1/4 (1.660) Setting Plate 1 3.10 E28736 7 1 (1.315) Setting Plate 1 3.15 E28735 7 3/4 (1.050) Setting Plate 1 3.20

INSERTS AOT # Item No. Description No. Req. Wt. (lbs.) E28772 8 2-1/16 & 2 LYT Insert 8 .25 E28775 8 1-1/2 (1.900) LYT Insert 8 .25 E28778 8 1-1/4 (1.660) LYT Insert 8 .25 E28749 8 1 (1.315) LYT Insert 8 .25 E29370 8 3/4 (1.050) LYT Insert 8 .25


10

AOT 40 TON MYT SLIP TYPE ELEVATOR

AOT # Description Size of Links Wt

E29328 MYT Elevator Complete Less Slip Assembly 1-1/4 2-3/4 148

MYT SLIP ASSEMBLIES

AOT # Description Wt (lbs.) E29343-1 2-7/8 x 2-7/8 MYT Slip Assembly 44.00 E29343-2 2-7/8 x 2-3/8 MYT Slip Assembly 46.00 E29343-3 2-7/8 x 2-1/16 MYT Slip Assembly 47.25 E29343-4 2-7/8 x 2 MYT Slip Assembly 47.50 E29343-5 2-7/8 x 1-1/2 (1.900) MYT Slip Assembly 48.75 E29343-6 2-7/8 x 1-1/4 (1.660) MYT Slip Assembly 49.75 E29343-7 2-7/8 x 1 (1.315) MYT Slip Assembly 49.75 E29343-8 2-7/8 x 3/4 (1.050) MYT Slip Assembly 51.00 E29343-10-S 2-7/8 MYT Slip Segments Only (Matched Set of 4) 31.00


11

MYT REPLACEMENT PARTS

AOT # Item No. Description No. Req. Wt. (lbs.) E29333 3 Hinge Pin 1 4.00 E30652 4 Latch 1 10.00 E29334 5 Latch Pin 1 4.00 E29338 6 Latch Spring 1 .50 E30653 7 Latch Lock 1 2.00 E29335 8 Latch Lock Pin 1 .50 E29349 9 Latch Lock Spring 1 .25 E30841 10 Latch Lock Door Pin 1 .50 E947128-120 11 Latch Pin Retainer 1 1.50 E947128-172 12 Latch Lock Pin Retainer 1 .50 E940308-1 13 Grease Fitting 1 .10 E30708 N/P Latch & Latch Lock Assembly 1 12.88 E29337 14 Link Block 2 1.00 E939009-65 16 Upper and Lower Link Block Bolts 4 .45 E939484-7 17 Link Block Nut 4 .20 E939672-18 18 Cotter Pin 4 .01 E29336 19 Slip Bolt 4 .75 E29340 20 Slip Spring 4 .25 E29347 21 Setting Ring Screw 2 .25 E939370-13 22 Setting Plate Washer 2 .06 E939098-15 23 Insert Retainer Screw 2 .13 E29344 25 Insert Retainer Plate 4 .50

INSERTS AOT # Item No. Description No. Req. Wt. (lbs.) E24773 24 2-7/8 x 2-7/8 Insert 8 .75 E29255 24 2-7/8 x 2-3/8 Insert 8 1.00 E29256 24 2-7/8 x 2-1/16 & 2 Insert 8 1.13 E29257 24 2-7/8 x 1-1/2 (1.900) Insert 8 1.25 E29258 24 2-7/8 x 1-1/4 (1.660) Insert 8 1.38 E29259 24 2-7/8 x 1 (1.315) Insert 8 1.44 E29259-1 24 2-7/8 x 3/4 (1.050) Insert 8 1.50

RECOMMENDED SPARES INCLUDE 1 SET OF INSERTS FOR EACH PIPE SIZE TO BE RUN

MYT SETTING RINGS AOT # Item No. Description Wt. (lbs.) E29348 28 2-7/8 MYT Setting Ring 6.50 E29345 28 2-3/8 MYT Setting Ring 6.63 E29350 28 2-1/16 MYT Setting Ring 7.00 E29351 28 2 MYT Setting Ring 7.10 E29352 28 1-1/2 (1.900) MYT Setting Ring 7.35 E29353 28 1-1/4 (1.660) MYT Setting Ring 7.50 E29354 28 1 (1.315) MYT Setting Ring 7.90 E29354-1 28 3/4 (1.050) MYT Setting Ring 8.05

RECOMMENDED SPARES INCLUDE 2 SETTING RINGS FOR EACH PIPE SIZE TO BE RUN


12

AOT 75 TON YT SLIP TYPE ELEVATOR


E23105 YT Elevator Less Slip Assembly 2-1/4 2-3/4 355

YT SLIP ASSEBLIES

AOT # Description Wt (lbs.) E23108-5 3-1/2 x 3-1/2 YT Slip Assembly 64.00 E23108-3 3-1/2 x 2-7/8 YT Slip Assembly 76.00 E23108-4 2-7/8 x 2-7/8 YT Slip Assembly 76.00 E23108-6 2-7/8 x 2-3/8 YT Slip Assembly 79.00 E23108-7 2-7/8 x 2-1/6 YT Slip Assembly 81.00 E23108-8 2-7/8 x 2 YT Slip Assembly 82.00 E23108-9 2-7/8 x 1-1/2 (1.900) YT Slip Assembly 83.50 E23108-10 2-7/8 x 1-1/4 (1.660) YT Slip Assembly 85.50 E23108-11 2-7/8 x 1 (1.315) YT Slip Assembly 86.50 E23108 3-1/2 YT Slip Segments Only (Matched Set of 4) 51.00 E23108-2 2-7/8 YT Slip Segments Only (Matched Set of 4) 51.00


13

YT REPLACEMENT PARTS

AOT # Item No. Description No. Req. Wt. (lbs.) E23116-1 3 Hinge Pin 1 4.13 E15348 4 Latch 1 27.00 E24182 5 Latch Pin 1 5.00 E12978 6 Latch Spring 1 .63 E12946 7 Latch Cam 1 1.50 E12972 8 Latch Lock 1 3.50 E13530 9 Latch Lock Pin 1 .63 E12529 10 Door Lug Pin 1 .65 E29464 11 Latch Pin Retainer 1 .20 E940308-1 12 Grease Fitting 1 .05 E940308-8 13 Grease Fitting 1 .05 E9519 14 Link Block 2 5.50 P8B .875 x 3 15 Upper Link Block Bolt 2 1.00 P8B .75 x 3 16 Lower Link Block Bolt 2 1.00 PSN .75 17 3/4 Slotted Nut 2 .25 PC .156 x 1.5 18 Link Block Cotter Pin 4 .05 E23115 19 Slip Bolt 4 1.25 E23113 20 Slip Spring 4 .25 E23630 21 Guide Plate 1 4.00 E939098-75 22 Guide Plate Screw 2 .25 E939098-64 23 Guide Plate Lock washer 2 .15 E27697 24 Setting Plate Bolt 4 .25 E27532 25 Insert Retainer Screw 4 .06 E27546 26 Setting Ring Retainer (3-1/2) 2 .13 E27507 26 Setting Ring Retainer (2-7/8) 2 .13 E27696 27 Rubber Bushing 4 .06 E24507 28 Insert Spacer (3-1/2) 8 .13 E24508 28 Insert Spacer (2-7/8) 4 .25 PSN .875 29 7/8 Slotted Nut 2 .25 E27530 31 Insert Retainer (3-1/2) 4 .13 E27541 31 Insert Retainer (2-7/8) 4 .25

YT INSERTS AOT # Item No. Description No. Req. Wt. (lbs.) E24774 30 3-1/2 x 3-1/2 Insert 24 .50 E30358 30 3-1/2 x 2-7/8 Insert 24 .75 E24773 30 2-7/8 x 2-7/8 Insert 12 .75 E29255 30 2-7/8 x 2-3/8 Insert 12 .75 E29256 30 2-7/8 x 2-1/16 & 2 Insert 12 1.00 E29257 30 2-7/8 x 1-1/2 (1.900) Insert 12 1.20 E29258 30 2-7/8 x 1-1/4 (1.660) Insert 12 1.38 E29259 30 2-7/8 x 1 (1.315) Insert 12 1.45


YT SETTING RINGS AOT # Item No. Description Wt. (lbs.) E27813 33 3-1/2 YT Setting Ring 3.13 E27695 33 2-7/8 YT Setting Ring 3.56 E27694 33 2-3/8 YT Setting Ring 4.00 E27812 33 2-1/16 YT Setting Ring 4.25 E28821 33 2 YT Setting Ring 4.25 E27811 33 1-1/2 (1.900) YT Setting Ring 4.31 E27810 33 1-1/4 (1.660) YT Setting Ring 4.38 E29001 33 1 (1.315) YT Setting Ring 4.75



14

AOT 75 TON YC SLIP TYPE ELEVATOR


E24140 YC Elevator Less Slip Assembly 3-1/2 7

YC SLIP ASSEMBLIES

AOT # Description Wt (lbs.) E24077-1 7 x 7 YC Slip Assembly E24077-1 7 x 6-5/8 YC Slip Assembly E24072-2 5-1/2 x 5-1/2 YC Slip Assembly E24072-7 5-1/2 x 5 YC Slip Assembly E24072-5 4-1/2 x 4-1/2 YC Slip Assembly E26830 4-1/2 x 4 YC Slip Assembly E34931 4-1/2 x 3-1/2 YC Slip Assembly E24072-4 4-1/2 Slip Segment Only (Matched Set of 4) E24072 5-1/2 Slip Segment Only (Matched Set of 4) E24077 7 Slip Segment Only (Matched Set of 4)


15

YC REPLACEMENT PARTS AOT # Item No. Description No. Req. Wt. (lbs.) E24181 3 Hinge Pin 1 4.13 E15348 4 Latch 1 27.00 E24182 5 Latch Pin 1 5.00 E12978 6 Latch Spring 1 .63 E12946 7 Latch Cam 1 1.50 E12972 8 Latch Lock 1 3.50 E13530 9 Latch Lock Pin 1 .63 E12529 10 Door Lug Pin 1 .65 E29464 11 Latch Pin Retainer 1 .20 E940308-1 12 Grease Fitting 1 .05 E940308-8 13 Grease Fitting 1 .05 E9519 14 Link Block 2 5.50 P8B .875 x 3 15 Upper Link Block Bolt 2 .50 P8B .75 x 3 16 Lower Link Block Bolt 2 .50 PSN .75 17 Lower Link Block Nut (3/4 Slotted Nut) 2 .25 PC .156 x 1.5 18 Link Block Cotter Pin 4 .05 E23115 19 Slip Bolt 4 1.25 E939354-6 20 Lock washer 4 E24049 21 Slip Spring 4 .25 E24075 22 Guide Plate Screw 4 .25 E939484-5 23 Guide Plate Nut 4 .15 E939672-17 24 Cotter Pin 4 .01 E30216 25 Retainer (3-1/2 7) 2 E30211 26 Shoulder Screw 4 E20213 27 Rubber Bushing 4 E941286-73 28 Insert Retainer Screw 4 PSN .875 29 Upper Link Block Nut (7/8 Slotted Nut) 2 E24056 32 Spacer 8

YC INSERTS AOT # Item No. Description No. Req. Wt. (lbs.) E16407 31 7 x 7 YC Insert 24 E24748 31 7 x 6-5/8 YC Insert 24 E16407 31 5-1/2 x 5-1/2 YC Insert 16 E24783 31 5-1/2 x 5 YC Insert 16 E16408 31 4-1/2 x 4-1/2 YC Insert 16 E24781 31 4-1/2 x 4 YC Insert 16 E24779 31 4-1/2 x 3-1/2 YC Insert 16

Recommended Spares Include 1 Set Of Inserts For Each Pipe Size To Be Run YC SETTING RINGS

AOT # Item No. Description No. Req. Wt. (lbs.) E30229 34 7 Setting Ring 1 E30226 34 6-5/8 Setting Ring 1 E30223 34 5-1/2 Setting Ring 1 E30220 34 5 Setting Ring 1 E30219 34 4-1/2 Setting Ring 1 E30209 34 4 Setting Ring 1 E34932 34 3-1/2 Setting Ring 1

Recommended Spares Include 2 Setting Rings For Each Pipe Size To Be Run YC RETAINERS

AOT # Item No. Description No. Req. Wt. (lbs.) E30214 33 3-1/2 4-1/2 Insert Retainer 4 2.75 E30221 33 5 Insert Retainer E30224 33 5-1/2 Insert Retainer 4 2.13 E30227 33 6-5/8 Insert Retainer 4 2.73 E30230 33 7 Insert Retainer

YC GUIDES PLATES AOT# Item No. Description No. Req. Wt. (lbs.) E24071-2 35 7 Guide Plate 2 3.75 E24071-3 35 6-5/8 Guide Plate 2 4.50 E24071-1 35 5-1/2 Guide Plate 2 5.50 E24071 35 5 Guide Plate 2 7.75 E24071-4 35 4-1/2 Guide Plate 2 8.50 E26827 35 4 Guide Plate 2 8.50 E26827-1 35 3-1/2 Guide Plate 2 8.00


16

AOT HYT 150 TON SLIP TYPE ELEVATOR

AOT # Description Range Size of Links Wt

E39284 HYT Elevator Complete Less Slips 2-3/8 3-1/2 2-1/4 3-1/2 740

HYT SLIP ASSEMBLIES

AOT # Description Wt (lbs.) E39258-2 3-1/2 x 3-1/2 HYT Slip Assembly 170 E39258-4 3-1/2 x 2-7/8 HYT Slip Assembly 170 E39259-2 2-7/8 x 2-7/8 HYT Slip Assembly 170 E39259-4 2-7/8 x 2-3/8 HYT Slip Assembly 170 E39174 3-1/2 HYT Slip Segments Only ( Matched Set of 4) 150 E39175 2-7/8 HYT Slip Segments Only (Matched Set of 4) 150


17

HYT REPLACEMENT PARTS

AOT # Item No. Description No. Req. Wt. (lbs.) E39239 3 Hinge Pin 1 12.40 E39162 4 Latch 1 22.00 E39238 5 Latch Pin 1 6.00 E39240 6 Latch Spring 1 .70 E39161 7 Latch Lock 1 8.00 E39251 8 Latch Lock Pin 1 .80 E39241 9 Latch Lock Spring 1 .70 E39253 10 Hinge Pin Retainer 1 .40 E39254 11 Latch Pin Retainer 1 .40 E940308-1 12 Grease Fitting 1 .10 E9519 13 Link Block 2 5.50 P8B .875 x 3 14 Upper Link Block Bolt 2 .50 P8B .75 x 3 15 Lower Link Block Bolt 2 .50 PSN .75 16 Lower Link Block Nut (3/4 Slotted Nut) 2 .15 PC .156 x 1.5 17 Link Block Cotter Pin 4 .05 E52321 18 Slip Bolt 4 1.00 E52539-1 19 Slip Spring 4 .80 E51090 20 Guide Plate 1 8.60 E939098-65 21 Guide Plate Screw 2 .10 E939352-64 22 Guide Plate Lock washer 2 .10 PSN .875 23 Upper Link Block Nut (7/8 Slotted Nut) 2 .15 E939098-96 24 Hex Head Cap Screw 2 .65 E939352-6 25 Lock washer 4 .10 E51089 26 Setting Ring Bushing 2 .15 E939098-36 27 Hex Head Cap Screw 2 .20 E39247 30 3-1/2 & 3-1/2 x 2-7/8 Insert Retainer 4 .25 E39246 30 2-7/8 & 2-7/8 x 2-3/8 Insert Retainer 4 .25

HYT INSERTS AOT # Item No. Description No. Req. Wt. (lbs.) E24774 29 3-1/2 x 3-1/2 Insert 32 .50 E30358 29 3-1/2 x 2-7/8 Insert 32 .75 E24773 29 2-7/8 x 2-7/8 Insert 16 .75 E29255 29 2-7/8 x 2-3/8 Insert 16 1.00


HYT SETTING RINGS AOT # Item No. Description No. Req. Wt. (lbs.) E39214-3 31 3-1/2 HYT Setting Ring 1 11.00 E39214-2 31 2-7/8 HYT Setting Ring 1 11.00 E39214-1 31 2-3/8 HYT Setting Ring



18

AOT HYC 200 TON SLIP TYPE ELEVATOR

AOT # Description Range Size of Links Wt

E55310 HYC Elevator complete less slips & bottom guides 3-1/2 7-5/8 2-1/4 3-1/2 978

HYC SLIP ASSEMBLIES

AOT # Description Wt (lbs.) E70009 7-5/8 x 7-5/8 HYC Slip Assembly 216 E55515 7 x 7 HYC Slip Assembly 224 E55514 7 x 6-5/8 HYC Slip Assembly 227 E55513 5-1/2 x 5-1/2 HYC Slip Assembly 243 E55512 5-1/2 x 5 HYC Slip Assembly 253 E55511 4-1/2 x 4-1/2 HYC Assembly 265 E55510 4-1/2 x 4 HYC Assembly 268 E55509 4-1/2 x 3-1/2 HYC Assembly 274 E55305-1 7-5/8 HYC Slip Segments Only (Matched Set of 4) 176 E55305 7 HYC Slip Segments Only (Matched Set of 4) 184 E55304 5-1/2 HYC Slip Segments Only (Matched Set of 4) 200 E55303 4-1/2 HYC Slip Segments Only (Matched Set of 4) 212


19

HYC REPLACEMENT PARTS

AOT # Item No. Description No. Req. Wt. (lbs.) E55311 1 Hinge Pin 1 25.00 E55503 2 Latch 1 47.00 E55312 3 Latch Pin 1 9.00 E34909 4 Latch Spring 1 1.50 E13185 5 Latch Spring Stop 1 .25 E13152 6 Latch Lock 1 4.00 E15101 7 Latch Lock Bolt 1 .75 E13188 8 Latch Lock Spring 1 .25 E8150 9 Latch Lock Bolt Nut 1 .25 E939672-19 10 Cotter Pin 1 .05 E13190 11 Door Lug Pin 1 .65 E55504 12 Hinge Pin Retainer 1 .35 E55505 13 Latch Pin Retainer 1 .20 E940308-1 14 Grease Fitting 1 .10 E9519 15 Link Block 2 5.50 P8B .875 x 3.00 16 Upper Link Block Bolt 2 .50 P8B .75 x 3.00 17 Lower Link Block Bolt 2 .50 PSN .75 18 Lower Link Block Nut (3/4 Slotted Nut) 2 .25 PC .156 x 1.50 19 Link Block Cotter Pin 4 .05 E24076 20 Slip Bolt 4 1.00 E939354-6 21 Lock Washer 4 .25 E945044-2 22 Slip Spring 4 .35 E55508 23 Guide Plate Screw 4 .25 E939484-5 24 Guide Plate Nut 4 .03 E939672-17 25 Cotter Pin 4 .05 E30216 26 Setting Ring Retainer (3-1/2 7) 2 .25 E70147 26 Setting Ring Retainer (7-5/8) 2 .30 E55501 27 Shoulder Screw 4 .41 E55502 28 Rubber Bushing 4 .04 E941286-73 29 Insert Retainer Screw 4 .08 PSN .875 30 Upper Link Block Nut (7/8 Slotted Nut) 2 .25 E70011 31 7-5/8 Insert Retainer 4 1.85 E30230 31 7 Insert Retainer 4 2.00 E30227 31 6-5/8 Insert Retainer 4 2.00 E30224 31 5-1/2 Insert Retainer 4 2.50 E30221 31 5 Insert Retainer 4 2.25 E30214 31 4-1/2 3-1/2 Insert Retainer 4 2.50 PSN .875 35 Upper Link Block Nut (7/8 Slotted Nut) 2 .25

HYC INSERTS AOT # Item No. Description No. Req. Wt. (lbs.) E70010 32 7-5/8 x 7-5/8 Insert 48 .50 E16407 32 7 x 7 Insert 48 .50 E24748 32 7 x 6-5/8 Insert 48 .75 E16407 32 5-1/2 x 5-1/2 Insert 36 .50 E24783 32 5-1/2 x 5 Insert 36 .80 E16408 32 4-1/2 x 4-1/2 Insert 24 .50 E24781 32 4-1/2 x 4 Insert 24 .80 E24779 32 4-1/2 x 3-1/2 Insert 24 1.00



20

HYC SETTING RINGS

AOT # Item No. Description No. Req. Wt. (lbs.) E70012 33 7-5/8 HYC Setting Ring 1 11.00 E55522 33 7 HYC Setting Ring 1 11.50 E55521 33 6-5/8 HYC Setting Ring 1 12.00 E55520 33 5-1/2 HYC Setting Ring 1 13.00 E55519 33 5 HYC Setting Ring 1 14.50 E55518 33 4-1/2 HYC Setting Ring 1 15.00 E55517 33 4 HYC Setting Ring 1 16.50 E55516 33 3-1/2 HYC Setting Ring 1 18.00


HYC BOTTOM GUIDE PLATE AOT # Item No. Description No. Req. Wt. (lbs.) E24071-6 34 7-5/8 HYC Bottom Guide Plate (Set) 1 5.00 E24071-2 34 7 HYC Bottom Guide Plate (Set) 1 7.50 E24071-3 34 6-5/8 HYC Bottom Guide Plate (Set) 1 9.00 E24071-1 34 5-1/2 HYC Bottom Guide Plate (Set) 1 11.00 E24071 34 5 HYC Bottom Guide Plate (Set0 1 15.50 E24071-4 34 4-1/2 HYC Bottom Guide Plate (Set) 1 17.00 E26827 34 4 HYC Bottom Guide Plate (Set) 1 17.00 E26827-1 34 3-1/2 HYC Bottom Guide Plate (Set) 1 16.00

RECOMMENDED SPARES INCLUDE 1 SET OF BOTTOM GUIDES FOR EACH PIPE SIZE TO BE RUN


21

CERTIFICATE OF WARRANTY AND GUARANTEE TO QUALITY

Seller warrants all materials, products and supplies manufactured or furnished by it to be free from defects in material and workmanship, under normal use and service, when installed, used and serviced in the manner provided and intended by seller for a period of twelve (12) months after installation or delivery, whichever shall occur first. Sellers obligations under this warranty are expressly limited to repair or replacement, at its option, of any materials, products or supplies returned to sellers plant, New Iberia, Louisiana, and which are determined by seller to be defective. All freight charges for return and reshipment shall be paid by customer. A new warranty period shall not be established for repaired or replaced materials, products or supplies; such items shall remain under warranty only for the remainder of the warranty period on the original materials, products or supplies. This is the sole warranty of seller and no other warranty is applicable, either expresses or implied, in fact or by law, including any warranty as to merchantability or fitness for a particular use or purpose.

In case of goods or parts not wholly of sellers manufacture, seller shall make available to the customer whatever warranty or guaranty is extended to seller for such goods or parts by the supplier or manufacturer thereof.

Seller will not assume responsibility or liability for any repairs, rebuilding, welding or heat treating done to its material, products or supplies outside of sellers plants, such work shall void any all warranties. All parts used in the manufacture and/or final assembly of sellers materials, products and supplies are necessary for both safety and operational performance. Omission of any part or failure to replace any part may result in a malfunction and a consequent safety hazard for which seller disclaims any responsibility or liability for injuries or damage as a result thereof.

Buyers sole and only remedy in regard to any defective materials, products or supplies shall be the repair or replacement thereof as herein provided, and seller shall not be liable for any consequential, special, incidental or punitive damages resulting from or caused by any defective materials, products or supplies.

Date post:	28-Sep-2015
Category:	Documents
Upload:	juan-jose-vesga-rueda
View:	4 times
Download:	0 times

20-1703

Documents