7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 1/30
RADWIN 2000Installation
V1.3Release 2.6.40 LA
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 2/30
Introduction
RADWIN Training Center 2
Easy and fast, self-installation
Ready for Installation, no pre-installation setting is required
Link alignment and synchronization without external means
Antenna alignment is based on buzzer (1 dB accuracy)
Four simple steps for the entire link configuration
Link Budget Calculator for network planning
Installation Rate 6.5 Mbps (BPSK) robust for all cases
Using a unique ID (SSID)
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 3/30
Between the sites» Line Of Sight (Azimuth)
»
Distance (<120 Km)» Potential Interference
On Site» Mounting procedure (Pole or Wall) ODU Grounding
» ODU-IDU Cable Routing (<100m)
» IDU Mounting and Power supply
Installation» Expected Results: “Link Budget Calculator”
» RADWIN Manager (NMS)
» Installation on PC Station
» Cable paving and IDU and ODU connection
» Power Up (AC/DC adaptor – IDU)
»
Antenna alignment (Buzzer) and Mounting» Run “Installation Wizard” via NMS
Site Survey
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 4/30
Installation Diagram
RADWIN Training Center 4
Dual Polarization
Antenna
Connectorized
ODU
Mounting
Pole
COAXCables
Grounding
Power feeds DC /
AC (via adapter)Dry Contact
To Network
CAT.5e ETH
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 5/30
Grounding
ODU Grounding
The system uses a Shielded CAT-5 cable to interconnect the ODU/IDU.
However, this shielding does not provide a good Lightning Discharge path, since it can not tolerate the high Lightning
Current surges.
In order to provide an alternate Lightning Discharge path, the ODU/Antenna Grounding posts should be connected to a
Ground Point by a 10 AWG short copper wire, as per NEC 810-21
IDU Grounding
The IDU’s grounding post should be connected to the internal Ground point, merely for Safety and ESD protection
reasons.
External Lightning Surge Suppressors
In order to minimize direct Lightning damages, an external well grounded CAT-5 Lightning Protector should be mounted
outside the building, located as near as possible to the entrance of the CAT-5 ODU-IDU interconnection cable.
3-rd party protectors may be used, e.g. Motorola’s 300SS, Hyperlink’s HGLN-CAT5 or Sixnet’s SP-ETH-2
Internal ESD Protection circuits
The system is designed to meet the ETSI / FCC /Aus/NZ / CSA EMC and Safety requirements
In order to fulfill these requirements, the system’s Telecom lines at the ODU/IDU are Transformer-isolated and include
internal ESD (Electro-Static-Discharge) Protection circuits
RADWIN Training Center 5
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 6/30
Proper lightning discharge path
Personnel safety guarantee
ESD (Electro-Static-Discharge) protection path
One of the major factors for RMAs is lack of grounding!
Grounding point
Grounding the ODU / IDU
Grounding point
RADWIN Training Center 6
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 7/30
Tower Collocation (ODUs are installed in crowded tower):
Use alternate/adjacent channels
At least 3 meters separation between co-located units
Use alternate polarization for adjacent channel units
Reduce Tx Power to the minimum based on LBC
Alternate frequency bands
Installation Guidelines
RADWIN Training Center 7
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 8/30
Antenna Alignment: Integrated / Bi-Polar
RADWIN Training Center 8
1. Set antenna (A) towards remote location (B) at 90°
Site A Site B
OFF
OFF
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 9/30
Antenna Alignment: Integrated / Bi-Polar
RADWIN Training Center 9
2. Power on Link and rotate antenna from 90° to 0°
Site A Site B
ONON
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 10/30
Antenna Alignment: Integrated / Bi-Polar
RADWIN Training Center 10
3. Rotate antenna from 0° to 180°
4. Scan back and listen to “buzzer” achieving
3 beeps – “best alignment”
Site A Site B
ONON
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 11/30
Antenna Alignment: Integrated / Bi-Polar
RADWIN Training Center 11
5. Mount the antenna in the “best alignment” position
6. Same for the elevation axis
7. Repeat for location B
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 12/30
Antenna Alignment: 2 External Mono-Polar
RADWIN Training Center 12
Using a coax cable with N-Type connectors, connect one antenna to the ANT 1 connector of the
ODU.
Align the first antenna following above slide
Unplug first antenna from ANT1 connector and connect it to ANT2 connector.
Using a coax cable with N-Type connectors, connect second antenna to the ANT 1 connector of the
ODU
Align the first antenna following above slide
* When working with one mono-polar antenna use ANT1 connector only!!
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 13/30
RADWIN Manager Default Parameters
Please note:
Only Installer mode allows for frequency band change, 5.3/5.4 GHz, and 2.5 GHz BRS configuration.
IP Address:» “Local Connection”- only used during day one
installation. Once link is configured, log in viaassigned IP address
Password:» Defined by which “User Type” is selected
User Type:» Operator- admin
» Installer- wireless
» Observer- admin
Read-Write Community: netman
RADWIN Training Center 13
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 14/30
Installation Wizard
RADWIN Training Center 14
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 15/30
Installation Wizard
RADWIN Training Center 15
After antenna alignment use
the installation wizard to
complete system
configuration
From this step and onward
you can examine the quality
and service availability of
the radio interface
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 16/30
Installation Wizard – Using the “Monitor Link”
RADWIN Training Center 16
When we launch the installation wizard, the ODUs fill in the Air Frame with Pilot Traffic to
evaluate the quality of the link, i.e. – what are the levels of existing interferences and
when do they exist
The Quality Bar shows the Service Availability According to the measured data
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 17/30
Installation Wizard – Link Attributes
RADWIN Training Center 17
Configure here:
Link ID
Link Name
Local Site Name
Remote Site Name
Link Password
Click “Next” to proceed
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 18/30
Installation Wizard – Changing Password
RADWIN Training Center 18
Click “Change” to change
the password
CLICK ME
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 19/30
Installation Wizard – Channel Selection (ACS)
RADWIN Training Center 19
Selecting all channels and
enabling ACS will allow the
Air Interface full flexibility
when determining the best
channel
You may narrow down the
number of channels that
participate in the process
You may also disable the
ACS process and select the
channels manually
Click “Next” to proceed
CLICK ME
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 20/30
Installation Wizard – Antenna Parameters
RADWIN Training Center 20
Click the “Configure”
button(s) to configure the
Antenna Parameters -
(see next slide)CLICK ME
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 21/30
Installation Wizard – Antenna Parameters
RADWIN Training Center 21
Antenna Parameters:
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 22/30
Installation Wizard - Service
RADWIN Training Center 22
Going back to the main menu
of the Installation Wizard,
here we can configure the
required Service:
ETH
ETH+TDM
Rate
You can initiate an “Evaluate”
check to re-examine the link
quality and availability
CLICK ME
CLICK ME
Next Slide
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 23/30
Installation Wizard – Configuring TDM Services
RADWIN Training Center 23
In this window you can select the
number of TDM ports
The total number of TDM ports
depend on the link quality and
availability
To select a port, simply click on the
RJ45 port icon(s)
CLICK ME
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 24/30
Installation Wizard – TDM Clock
RADWIN Training Center 24
To configure the clock
settings of TDM port(s),
simply right-click the port and
select the best scenario -
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 25/30
Installation Wizard
RADWIN Training Center 25
That’s it!
You have successfully
configured both sites of the
link
You’re ready to go….
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 26/30
Installing the Lightning Protection Kit
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 27/30
LP – Packing List
Item Quantity
LP Unit 1
Pole Mounting Band 1
Wall Mounting Unit 1
Shielded RJ45 Male Connector 2
CAT-5e Cable 50 cm 1
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 28/30
Installing the LP on the Tower (ODU End)
Before commencing with the installation, please read carefully the
following instructions:
Basic installation requires mounting and grounding 2 Lightening
Protection Units; One on the tower very close to the ODU and
another outside of the site/facility where the IDU is installed.
Instructions:
1. Mount the LP on the tower as close as possible to the ODU using the mounting ring
2. Ground the LP Unit using the GND screw
3. Connect the short CAT5e cable to the IDU connector on the ODU
4. Connect the other side of the cable to the LP Unit
5. Tighten the cable gland cap firmly
6. Connect the CAT-5e cable that goes to the IDU to the other side of the LP Unit.
7. Tighten the cable gland cap firmly8. Run the CAT-5e cable towards the IDU
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 29/30
Installing the LP next to the IDU/PoE
Instructions:
9. Mount the 2nd LP Unit as close as possible to the inlet hole of the site/facility where the IDU/PoE is installed10. Use the Wall Mounting Unit to firmly secure the LP Unit on the site/facility wall
11. Ground the LP Unit using the GND screw
12. Remove the cap of the cable gland that is facing the ODU, make sure you remove the rubber sealing tube as
well
13. Plug into the half open cable gland the CAT-5e cable coming from the ODU
14. Tighten the cable gland cap firmly
15. Connect the short CAT-5e cable (provided in kit) to the half open cable gland of the LP and the other end
16. Connect the other end of the short CAT-5e cable to the IDU/PoE
7/18/2019 2006 - RW2000 - Installation v1.3 Copy
http://slidepdf.com/reader/full/2006-rw2000-installation-v13-copy 30/30
Thank You!