Point-to-PointMicrowave RadioEquipment forData and VoiceCommunicaon

Produced in Europe

SAF Tehnika is among the world’s top microwave carrier-class point-to-point radio manufacturers, publicly traded in NASDAQ, ISO certified, with R&D and complete production in Europe, covering spectrum 1.4-38 GHz and licence-free 24 GHz with capacities up to 720 Mbps full-duplex.

The company offers 2 main product lines: CFIP series – the latest 1.4 GHz Marathon FIDU (long-haul), 366 Mbps Lumina FODU (Optical&Electrical Gigabit Ethernet), CFIP-108 FODU (Fast Ethernet) and 366 Mbps CFIP PhoeniX Hybrid Split Mount System;SAF FreeMile – 100Mbps full duplex licence-free FODU.

SAF Tehnika

CFIP FODU Technical Specification

Radio & Modem Full outdoor system with built-in radio, modem and traffic interfaces

Product name CFIP - 108 FODU CFIP Lumina FODUFrequency Bands 6, 7, 8, 10, 11, 13, 15, 18, 23, 24, 26, 38 GHzCapacity Up to 108 Mbps Up to 366 Mbps

Channel bandwidth 7/14/28 MHz 28/40/56 MHz

Modulation QPSK, 16APSK, 32APSK, 64QAM; for 14MHz bw only: 128QAM

QPSK, 16APSK, 32APSK, 64QAM, 128QAM, 256QAM (for all bw)

Protection Switching 1+0 Ring/Mesh (with STP)

1+0, Ring/Mesh (with RSTP), 2+0 (Ethernet Aggregation)

ACM switching Hitless

InterfacesEthernet port 1xRJ-45 (electrical) 1 or 2 RJ-45 (electrical)

or 1 or 2 ODC (fiber optical)E1 4xE1 (18-pin connector) nonePower PoE+ (not IEEE standard) Outdoor power connectorRSSI port BNCSerial Port Dual-BNCConnection to antenna Standard flange according to frequency

CFIP Lumina FODUCFIP - 108 FODU

CFIP-108 is primarily designed for IP networks and provides Fast Ethernet interface with capacities from 8 Mbps up to full duplex 100 Mbps Fast Ethernet. In addition to that, CFIP-108 has a 4xE1 port for legacy equipment connectivity and for use in hybrid TDM/IP networks.

CFIP Lumina systems are intended for Gigabit Ethernet backbone applications delivering up to 366 Mbps per radio. 2+0 aggregation is available for higher bandwidth users. Both single or dual, electrical and fibre optical interface versions are available.

ManagementManagement ports RJ-45 (same as traffic port) RJ-45 (electrical) or ODC (optical)Management In-band In-band (traffic port) or VLAN port seperatedSNMP SNMP traps, MIB, SNMP v1/v2cEMS Web based HTTP, Telnet, FTP, TerminalPerformance graphs Uptime, Rx level, Tx level, System temperature, Radial MSE, LDPC decoder stress,

constellation diagram, equalizer graphEthernet performance Per port Ethernet counters, Enhanced radio Ethernet statisticsLoopbacks E1, modem, IF loopback

CFIP FODU Ports

CFIP-108- RJ-45- 18-pin (balanced E1)- BNC (RSSI)- Twin BNC (Serial)

CFIP Lumina Optical- 1 or 2 optical ODC (Eth)- 48V DC (Power)- BNC (RSSI)- Twin BNC (Serial)

CFIP Lumina Electrical- 1 or 2 electrical RJ-45 (Eth)- 48V DC (Power)- BNC (RSSI)- Twin BNC (Serial)

Modulation

Channel bandwidths (MHz)

CFIP-108 FODU CFIP Lumina FODU

7 14 28 28 40 56

QPSK 8 - 9 17 - 19 35 - 40 35 - 40 49 - 58 72 - 85

16APSK 16 -19 34 - 40 69 - 82 69 - 82 98 - 114 135 - 160

32APSK 21 - 24 43 - 50 100 - 108 88 - 103 127 - 146 186 - 214

64QAM 28 - 30 57 - 62 - 115 - 128 163 - 179 241 - 267

128QAM - 68 - 74 - 138 - 151 196 - 212 289 - 315

256QAM - - - 161 - 174 229 - 245 337 - 366

CFIP-108 and CFIP Lumina FODU total payload capacity (Mbps)

EthernetSwitch Type Managed Fast Ethernet Layer 2 Managed Gigabit Ethernet Layer 2

Max frame size 1916 bytes 9728 bytes

MAC table 1K entries; automatic learning and aging 4K entries; automatic learning and aging

Packet buffer 32KB; non-blocking store&forward 128KB; non-blocking store&forwardFlow Control 802.3x

QinQ (Double Tagging) Yes

QoS 64 level DiffServ (DSCP) or 8 level 802.1p mapped in 4 prioritization queues with VLAN support

QoS queuing Yes Fixed or weighted (configurable ratio)

VLAN support 802.1Q (up to 15 concurrent traffic VLANs) 802.1Q (up to 4K VLAN entries)

Spanning Tree Protocol 802.1D-1998 STP 802.1D-2004 RSTP, 802.1Q-2005 MSTP

Mechanical & ElectricalPower consumption 19 - 26 W 25 - 33 W (SP) / 29 - 41 W (HP)

Weight 3.5 kg 3.9 kg

Temperature Range -33°C to +55°C

Dimmensions: HxWxD, mm 288x288x80

Radio & ModemProduct name CFIP PhoeniX Split Mount CFIP PhoeniX M Split MountFrequency Bands 6, 7, 8, 10, 11, 13, 15, 18, 23, 26, 38 GHzCapacity IDU: up to 366 Mbps

ODU Unified Band: 8 - 366 Mbps ODU Wide Band: 34 - 366 Mbps

IDU: up to 348 Mbps, up to 63E1, up to 2xSTM-1 per every 1+0 link ODU Unified Band: 8 - 348 Mbps

Channel bandwidth IDU: 3.5/7/14/28/40/56 MHzODU Unified Band: 3.5/7/14/28/40/56 MHz

IDU: 7/14/28/40/56 MHzODU Unified Band: 7/14/28/40/56 MHz

Modulation QPSK, 16QAM, 32QAM, 128QAM, 256QAMProtection Switching 1+0, 1+1 (HSB, SD, FD), Ring/Mesh (with RSTP),

2+0, 3+0, 4+0 (Ethernet Aggregation)1+0, 1+1 (HSB, SD, FD), Ring/Mesh (with RSTP),

E1 ring protection, STM-1 Add/Drop, 2+0, 3+0, 4+0 (Ethernet Aggregation)

ACM switching Hitless Yes

ManagementManagement ports RJ-45, DB-9 2xRJ-45, DB-15Management In-band Out-band managamentSNMP SNMP traps, MIB, SNMP v1/v2c SNMP traps, MIB, SNMP v1/v2/v3EMS Web based HTTP, Telnet, FTP, TerminalPerformance graphs Uptime, Rx level, Tx level, System temperature, Radial

MSE, LDPC decoder stress, constellation diagram, equalizer graph

Rx level, Tx level, System temperature, Signal/Noise (SNR) level, System performance, constellation diagram,

equalizer graphEthernet performance Per port Ethernet counters, Enhanced radio Ethernet

statisticsEthernet switch statistics

Loopbacks E1, modem, IF loopback Modem, radio, E1 (local, tremote) loopbacks

EthernetSwitch Type Managed Gigabit Ethernet Layer 2

Max frame size 9728 bytes

MAC table 4K entries; automatic learning and aging

Flow Control 802.3x

QinQ (Double Tagging) Yes

QoS 64 level DiffServ (DSCP) or 8 level 802.1p mapped in 4 prioritization queues with VLAN support

64 level Diffserv (DSCP) or 802.1Q VLAN Tag Priority, IPv4 TOS priority, Port priority

QoS queuing Fixed or weighted (configurable ratio) Weighted

VLAN support 802.1Q (up to 4K VLAN entries)

Spanning Tree Protocol 802.1D-2004 RSTP, 802.1Q-2005 MSTP 802.1D-1998 STP, 802.1D-2004 RSTP

Mechanical & ElectricalPower consumption IDU: 20 - 30W ODU: 13 - 18W IDU: 30 - 40W

ODU: 13 - 18WWeight IDU: 3.1 kg

ODU: 3.5kgIDU: 3.4 kg ODU: 3.5kg

Temperature Range IDU: -5°C to +45°C ODU: -33°C to +55°C

IDU: -5°C to +55°C ODU: -33°C to +55°C

Dimmensions: HxWxD, mm IDU: 1U rack (45x430x240) ODU: 288x288x80

IDU: 1U rack (44.5x445x238.5) ODU: 288x288x80

CFIP PhoeniX Split Mount CFIP PhoeniX M (Modular) Split Mount

CFIP PhoeniX split mount system is designed to fit in classical telecom architecture with a radio located outdoors and a sheltered indoor unit. CFIP PhoeniX also enables transition from TDM networks to hybrid TDM/IP networks providing up to 20E1 + GigE. Total maximum capacity is up to 366 Mbps full duplex.

CFIP PhoeniX M split mount system consists of PhoeniX M IDU and PhoeniX ODU (also with XPIC functionality). PhoeniX M IDU provides up to 63E1 and 2xSTM-1. Total maximum capacity is up to 348 Mbps full duplex.

CFIP Split Mount Technical Specification

CFIP PhoeniX ODU Ports - N-type (data + power)- BNC ( RSSI)

Modulation

Channel bandwidths (MHz)CFIP PhoeniX IDU CFIP PhoeniX M IDU*

7 14 28 40 56 7 14 28 40 56

QPSK 8 - 10 17 - 21 35 - 40 49 - 58 72 - 85 8 17 36 52 74

16APSK 17 - 19 34 - 41 69 - 82 98 - 114 135 - 160 16 36 74 108 144 - 152

32APSK 21 - 24 45 - 52 88 - 103 127 - 146 186 - 214 21 46 94 132 192

64QAM 28 - 31 57 - 64 115 - 128 163 - 179 241 - 267 ** 55 112 164 232

128QAM 34 - 36 68 - 75 138 - 151 196 - 212 289 - 315 - ** 128 - 136 188 264

256QAM - 79 - 86 161 - 174 229 - 245 337 - 366 - - 144 - 160 - 312 - 348

CFIP PhoeniX M Split Mount IDU Interfaces

CFIP PhoeniX M IDU Interfaces

CFIP PhoeniX and CFIP PhoeniX M IDU total payload capacity (Mbps)

Ethernet port 4xRJ-45 (electrical)

E1 20E1 (RJ-45)

Power IDU power connector

RSSI port ODU: BNC

Serial Port DE9 (RS-232)

EOW 2x 3.5mm headset ports (Mic&Speaker)

Alarm port DB26HD

1+1 Port RJ-45

IDU-ODU connection N-Type

Connection to antenna Standard flange according to frequency

Bas

e M

odul

es

Standard Base - Link capacity: 50 / 100 / 155Mbps A standard module provides connectivity up to 155Mbps. By adding an expansion module – up to

37 x E1. Interfaces: • 14 x E1, high-density Molex connector; • 2 x E1, RJ-48C connector; • Voice, Data ORW RJ-48C connectors; • 100BaseTX, 25-100 Mbps, two RJ-45 ports

Enhanced Base - supports ADM up to 63E1 via STM-1

42E1 Base Provides 63E1 capacity with 21E1 expansion module. Interfaces: • 42 x E1, 3x high-density Molex connector; • Voice, Data ORW RJ-48C connectors; • 100BaseTX, 25-100 Mbps, two RJ-45 ports

GigE Base Provides connectivity for Gigabit Ethernet. Interfaces:4x10/100/1000Base-T ports with RJ-45 connector; Ethernet SFP port; • 2 x E1, RJ-48C connector; • Voice, Data ORW RJ-48C connectors

Enhanced GigE Base with jumbo frames up to 9000 bytes packet

Enhanced GigE Base - supports ADM up to 63E1 via STM-1

Opt

iona

l Mod

ules

16E1 Expansion module • 14 x E1, high-density Molex connector; • 2 x E1, RJ-48C connector

21E1 Expansion module 21 x E1, 2x high-density Molex connector

STM-1 Optical mini module STM-1, Single mode 1310 nm, SC Duplex Transceiver. Unconditionally eyesafe laser IEC 825/CDRH Class 1 Compliant

STM-1 Electrical mini module STM-1, 2xBNC, ITU-T Rec. G.703, 75 Ω

2xSTM-1 Optical expansion module 2xSTM-1, Single mode 1310 nm, SC Duplex Transceiver. Unconditionally eyesafe laser IEC 825/CDRH Class 1 Compliant

2xSTM-1 Electrical expansion module2xSTM-1, 2xBNC, ITU-T Rec. G.703, 75 Ω

2xSTM-1 SFP module2 SFP ports for connection various optical or electrical adapters corresponding to STM-1 standards

* Capacities are subject to change ** Under development

nHigh capacity system with up to 20E1 and up to 366 Mbps Gigabit Ethernet - ideal for building hybrid networks to facilitate transition from TDM to IP;

nIndustrial grade fanless design increases reliability and enables low power consumption;

nLeading edge technology utilizing 256QAM modulation and 56MHz channel bandwidth allows high capacity throughput up to 366 Mbps;

nExcellent upgrade for existing PDH split mount systems;

nUp to 4094 concurrent VLAN traffic allows building many port-to-port networks paths for specific client services;

nJumbo frame size support (up to 9728 bytes), allows using longer header info (VLAN, MPLS) and transmitting more useful content and less headers, thus gaining on total throughput.

CFIP PhoeniX Highlights

nExcellent system gain allows to efficiently upgrade PDH radios to 108 Mbps capacity without increasing antenna sizes;

nLow power consumption enables Power over Ethernet and use of solar/wind energy;

nACM and ATPC for high availability and high density deployments;

nVery high flexibility allows to configure the system to various channel bandwidths, modulation schemes and capacity settings.

nSNMP support for remote network monitoring and mana-gement.

CFIP-108 FODU Highlights

nLeading edge technology with up to 256QAM modu-lation and 56MHz channel bandwidth allows high capacity throughput up to 366 Mbps;

nOptical Ethernet connections provide excellent protec-tion against lightning strikes and allow long distances between user equipment and the radio;

n2 Gigabit Ethernet ports provide the convenience of having separate ports for management (both basic and advanced) and user traffic;

nUp to 4094 concurrent VLAN traffic allows building many port-to-port networks paths for specific client services;

nJumbo frame size supports up to 9728 bytes, which allows using longer header info (VLAN, MPLS) and transmitting more useful content and less headers, thus gaining on total throughput;

nACM and ATPC for high availability and high density deployments.

CFIP Lumina Highlights

nRing configuration with built-in add-drop functionality for up to 63E1;

n348Mbps radio (56MHz) for capacities of up to 933 Mbps per link in 3+0 configuration;

n63E1 + 25-30Mbps Ethernet with a single ODU (28 MHz);nEasy upgrade of existing set-up to 1+1 or 2+0, 3+0, 4+0

configurations with GigE.

CFIP PhoeniX M Highlights

SAF CFIP-108, CFIP Lumina and CFIP PhoeniX ODU max Tx Power

Application diagram of CFIP Products

Application diagram of CFIP PhoeniX M

Modulation Standard/High Tx Power, dBm6, 7, 8 GHz 10, 11, 13, 15 GHz 18, 23, 26 GHz 24 GHz 38 GHz

QPSK +19 / +27 +19 / +25 +19 -20 to 0 +1216APSK +18 / +26 +18 / +24 +18 -20 to -1 +1132APSK +17 / +25 +17 / +23 +17 -20 to -2 +1064QAM +15 / +23 +15 / +21 +15 -20 to -4 +8128QAM +15 / +23 +15 / +21 +15 -20 to -4 +8256QAM +12 / +20 +12 / +17 +12 -20 to -7 +5