Date post: | 23-Dec-2015 |
Category: |
Documents |
Upload: | gervais-long |
View: | 217 times |
Download: | 0 times |
2012 Advisory PanelElectromechanical System Solutions
Joe BenoCenter for Electromechanics
The University of Texas at Austin12/4/2012
Introduction
• Electromechanical System Solutions– Synergistic combination of electromechanical
hardware (actuators, motors, generators); controls and related software; sensors and related software; communication and related software; transducers; power electronics; processors; materials science; and all interconnections.
• Key applications– Almost any electrically powered device or system that
moves itself or something else under its own power.– This talk focuses on motion control systems,
actuation systems, robotic systems and anything else not covered by other talks.
Key Challenges – Get Ahead of the Wave (or at least ride it!)
1. Exploit advances in all related fields, especially computation, analysis and power electronics.
2. Improve Integration and Systems Engineering.3. Identify commercially viable products and
commercially viable new science.
Source: Lyshevski textbookon Mechatronics
Mechatronics: New engineering discipline that emerged in ~2000.CEM vision also includes material science and systems engineering.At Universities the disciplines of Electrical Engineering, Computer Science, Mechanical Engineering and Material Sciences are still largely represented by separate departments – after 40 years CEM still needed to focus on cross discipline applications.
Significant Recent Programs
Hobby Eberly Telescope• 20 ton robot to move
optical package along trajectories to
within ~5
microns in real
time.
Significant Recent Programs
Giant Magellan Telescope Azimuth and Elevation Drives Design Study
• New class of super large telescopes• Operational in ~2020 in Atacama Desert, Chile• 7 Large mirrors, viewing area 80 ft in diameter• Long circular track (~60 m); permanent magnet
direct drive solution• 4 forcer heads per track, ~6,700 lbf total• Integrate with GMT control system• Less than 2% force ripple (desire close to 0.1%)• Must stay with 2o C of ambient• Minimize size and weight
Significant Recent Programs
Oshkosh 90,000 lb Airport Rescue and Firefighting (ARFF) Active Suspension System
• 2.5x to 4x increase in vehicle per wheel mass compared to previous vehicles
• Required hybrid power train development: 10 Farad Cap storage, 200 kW peak power, 48 kW avg power
• 6 actuators, each with 17,300 lbf peak and 6,600 lbf continuous
• 3.5x force and 2x speed (7 m/s wheel vertical speed) of previous suspension actuators
• Result: 3x increase in cross country speed• Result: Greatly improved handling and
safety – eliminates roll on high g turns
Significant Recent Programs
NASA Vibration Isolation System• Isolates electronics racks on heavy lift
vehicle launch platforms (e.g., space shuttle mobile launch platform).
• Disturbance rejection up to 2 kHz (high bandwidth actuators)
• 2.75 ton payload• Vertical velocity primarily less than 1 m/s• Actuator stroke ~6 inches• Very low friction system• Developed new “voice-coil” actuator
Recent and Ongoing Smaller Scale EM System Examples
• High Temperature Superconducting Magnetic Bearings for Ultra Low Loss Flywheel Systems
• Aggregate Screen Actuator (sifts and separates gravel by size; 100 Hz, 3250 lbf, homopolar actuator with PM bias)
• Canfield Joint as Gimbal Replacement System for Satellite Reaction Wheels (~2 kg)
• Small programs with potential to expand CEM expertise and applications
Key CEM Strength – Balanced System Design
Geared Actuator Weight vs. Gear Ratio Active Suspension Alternator
System Design
Power Electronics
Mechanical Advantage
Power Source
Auxiliaries
~3 MW Flywheel Battery & Power Electronics
High Peak-to-AverageDual Motor Controller
Key CEM Strength – Multidisciplinary Analysis
Specifications X axis,140 turns @ 12 Amps per coil M19 Laminations 0.063 in, 1.5 deep Air gap 0.100 in @ 14 in diameter O.D. 20 in, I.D. 8 in 0 Hz Neumman Boundary Conditions
x x
EM FEA of Coil Circuit of Screen Actuator
Key CEM Strength – Effective Use of Energy Storage
Flywheel
Mechanical Springs
PM (Potential Energy)
Caps; Ultra-Caps
Batteries
How To Develop $3M to $5M New Annual Funding for EM Systems
Identify and Develop New Opportunities• CEM traditional customer’s budgets are declining. Their response: keep current staff and
reduce/eliminate external contracts (Army R&D centers/labs, NASA, ONR)– One exception: Small Business Innovative Research (SBIR) and Small Business
Technology Transfer (STTR) programs: established by Congress and must be externally contracted to small businesses
• Some military system procurements surviving– More focused on application of existing technology, more production oriented, less
research– More focused on OEM’s
• DOE: Doing energy research (a CEM strength), but has major cost share requirements• Impact:
– Must develop new customers (DARPA, industry)– Must team with industry more for military procurements– Must team with industry more for SBIR/STTR’s (small contracts with opportunities for
expanding CEM areas of expertise)– Must team with industry more for DOE opportunities– CEM program mangers must expand outreach to industry and new customers (travel)
How To Develop $3M to $5M New Annual Funding for EM Systems
Identify and Exploit New/Emerging Technology• CEM uniqueness is applied R&D through advanced prototype hardware
– Usually (but not always) exploits basic R&D or new products from other organizations• Example: Toray T1000G fiber critical to increased flywheel energy density that
was significant motivation for government sponsors to fund CEM flywheel research in the 1990’s and early 2000’s.
• Example: Emerging permanent magnet materials and improved processing/controls critical to development active magnetic bearings that was significant motivation for government sponsors to fund CEM flywheel research in the 1990’s and early 2000’s.
• Example: Emerging COTS motor generators, advanced analysis capabilities, new processing/controls technology critical to CEM active suspension program from 1993 to ~2005.
• Has been a major source of CEM innovation in the past.• Impact:
– CEM must expand outreach efforts to identify new/emerging technology– CEM must expand awareness of relevant R&D developments and their potential
before industry and other R&D organizations
How To Develop $3M to $5M New Annual Funding for EM Systems
Develop New Areas of CEM Expertise• Active funded areas of R&D grow old and funding wanes.
– Newness and excitement wears off.– Upcoming government and industry leaders want to make their own mark.– Sometimes, after sufficiently long lulls, R&D area re-emerges
• New technology expands possibilities• Other options don’t pay off and they wear out their welcome
• Impact:– CEM must continually develop new areas of expertise– Past examples: flywheel energy storage systems, active suspension systems, oil and
gas support areas (subject of later talk); telescope movement control systems– How to establish a new area of expertise?
• Get smart through equivalent of IR&D• Team with other experts• Establish a presence through papers, conferences, meetings, outreach.
How To Develop $3M to $5M New Annual Funding for EM Systems
Required Resources• One 3 day trip per month (~$1,800 average travel cost per trip)
– Cultivating new sponsors, joint planning/budgeting/proposing activities with industry members, visiting government agencies, attending meetings, and attending 2-3 conferences per year
– 0.5 days planning and arranging trip, preparing briefings, etc.– 1 day follow-up from trip
• 2 hrs per day when not on travel for white papers, responding to budget requests, maintaining contact and presence with sponsors and team members, searching for funding opportunities, etc.
• 3 major proposal efforts per year (4 PI man-days and 4 engineering support man-days each)
• Total: ~$9.5K / month• My current B&P budget: $1,670/month (not enough to cover one average trip
if I use vacation time to cover my labor cost).• If successful, UT will earn $1M to $1.6M in overhead and CEM will receive
$290K to $500K direct funding for admin, lab services, software, etc. per year after the building year.
Near Term Focus• Re-energize flywheel energy storage programs
– After having plateaued for ~20 years, Carbon Nanotubes (CNT) offer 30-50% improvement in energy density in near term to reinforce existing carbon fibers and 1 to 2 orders of magnitude in long term to replace existing carbon fibers
• Team with organizations with appropriate CNT expertise• Exploit SBIRs/STTRs to get started and build technology and “presence”• Will significantly outperform other forms of energy storage (e.g., Li batteries)• Cost will be an issue
– After having plateaued for ~20 years, magnetic bearings are poised to make major step in efficiency through use of High Temperature Superconducting (HTS) Trapped Field Magnets (TFM)
• Also exploits advancements in COTS cryo-cooling technology• Builds on CEM recognized expertise in HTS generators • Builds on past CEM STTR for HTSMBs for flywheels• Exploit SBIRs/STTRs to get started and build technology and “presence”
– Government is showing renewed interest in flywheel energy storage systems (Li batteries are showing initial signs of wearing out their welcome)
– NASA has major internal flywheel development program, needs CEM composite and HTSMB expertise, and want to team with CEM to go after DARPA money
• Favorable circumstance: new DARPA program manager, friend of NASA, and flywheel advocate– Flywheel Technology Status and Roadmap paper may help focus Government funding
Near Term Focus
• Exploit leading edge telescope motion control system expertise– Follow-on to Giant Magellan Telescope main axis drives system study– Several consortiums have new super large telescopes in various stages
of planning and design– Contracts often spread among consortium members and consortium
countries• Continue to pursue industry support for active suspension projects
– Builds on existing CEM customers and CEM active suspension reputation
– New Government interest in Semi-active suspension systems (subset of CEM technology
• Expand to new areas– Robotics
• U.S. lags in industrial robots but leads in compliant robots that physically interact with humans
• Have will continue to team with Professor Deshpande, U.T. Department of Mechanical Engineering