The information contained in this publication was correct at the time of going to print. In the interest ofcontinuous development, we reserve the right to change specifications, design or equipment at any timewithout notice or obligation. No part of this publication may be reproduced, transmitted, stored in aretrieval system or translated into any language in any form by any means without our written permission.Errors and omissions excepted.© Ford Motor Company 2011
All rights reserved.Part Number: AB39120609AA (CG3575en) 08/2011 20110902084522
IntroductionAbout This Manual...........................................7Symbols Glossary.............................................7Parts and Accessories....................................8
At a GlanceAt a Glance..........................................................9
Child SafetyChild Seats.........................................................16Child Seat Positioning....................................17ISOFIX Anchor Points....................................19Booster Seats..................................................20Child Safety Locks...........................................21
Occupant protectionPrinciple of Operation...................................22Fastening the seat belts..............................24Seat belt height adjustment......................24Seat belt reminder.........................................25Using seat belts during pregnancy..........25Disabling the passenger airbag................25
Keys and Remote ControlsGeneral Information on Radio
Frequencies..................................................27Programming the remote control............27Changing the remote control
battery............................................................28
LocksLocking and Unlocking.................................29Global Opening and Closing.......................31
Engine immobiliserPrinciple of Operation...................................33Coded keys........................................................33Arming the engine immobiliser.................33Disarming the engine immobiliser...........33
AlarmPrinciple of Operation..................................34Arming the alarm...........................................35Disarming the alarm.....................................35
Steering WheelAdjusting the Steering Wheel...................36Audio Control...................................................36Voice Control....................................................37
Wipers and WashersWindscreen Wipers.......................................38Autowipers.......................................................38Windscreen Washers....................................39Checking the Wiper Blades........................39Changing the Wiper Blades.......................39
LightingLighting Control...............................................41Autolamps........................................................42Front Fog Lamps............................................42Rear Fog Lamps..............................................43Headlamp Levelling......................................44Hazard Warning Flashers............................44Direction Indicators.......................................45Interior Lamps.................................................45Changing a Bulb.............................................45Bulb Specification Chart..............................51
Windows and MirrorsPower Windows..............................................52Exterior Mirrors................................................54Electric exterior mirrors................................54Sliding Windows.............................................55
Instrument ClusterGauges...............................................................56Warning Lamps and Indicators................56Audible Warnings and Indicators............60
1
Table of Contents
Information DisplaysGeneral Information......................................62Trip Computer.................................................62Personalised Settings..................................65
Climate ControlPrinciple of Operation..................................66Air Vents............................................................66Manual Climate Control..............................66Automatic Climate Control........................69Heated Windows and Mirrors.....................71
SeatsSitting in the Correct Position....................72Front Seats........................................................72Head Restraints..............................................76Rear Seats.........................................................76Heated Seats....................................................77
Convenience featuresClock....................................................................79Instrument Lighting Dimmer......................79Cigar Lighter.....................................................79Ashtray...............................................................79Auxiliary Power Points.................................80Cup Holders.....................................................80Glasses Holder.................................................81Storage compartments................................81Auxiliary input (AUX IN) socket................82USB port............................................................82Cool Box............................................................82Floor Mats.........................................................83
Starting and Stopping theEngine
General Information.....................................84Ignition Switch................................................84Steering Wheel Lock.....................................84Starting a Petrol Engine..............................84
Starting a Diesel Engine..............................85Diesel Particulate Filter................................85Switching Off the Engine............................86
Fuel and RefuellingSafety Precautions........................................87Fuel Quality - Petrol......................................87Fuel Quality - Diesel......................................87Catalytic Converter........................................87Fuel filler flap..................................................88Refuelling..........................................................90Fuel Consumption.........................................90Technical Specifications.............................90
TransmissionManual Transmission...................................92Four-Wheel Drive...........................................92Electronic Locking Differential..................93Automatic Transmission.............................94
BrakesPrinciple of Operation...................................97Hints on Driving With Anti-Lock
Brakes.............................................................97Parking Brake...................................................97
Hill descent control (HDC)Principle of Operation..................................98Using Hill Descent Control.........................98
Stability ControlPrinciple of Operation................................100Using Stability Control...............................100
Hill Start AssistPrinciple of Operation.................................102Using hill start assist...................................102
2
Table of Contents
Parking AidsPrinciple of Operation................................104Using the Parking Aid - Vehicles With:
Rear Parking Aid.......................................104
Rear view cameraPrinciple of Operation.................................107Using the Rear View Camera...................107
Cruise ControlPrinciple of Operation................................109Using Cruise Control...................................109
Load CarryingGeneral Information......................................111Tailgate...............................................................111Load Retaining Fixtures................................111Roof Racks and Load Carriers..................114
TowingTowing a Trailer..............................................116Tow Ball............................................................118
Driving HintsGeneral Driving Points................................120Running-In.......................................................120Cold Weather Precautions........................120Reduced Engine Performance.................120Driving Through Water.................................121
Roadside EmergenciesFirst Aid Kit......................................................122Warning Triangle...........................................122
FusesFuse Box Locations......................................124Changing a Fuse............................................125Fuse Specification Chart...........................126
Vehicle recoveryTowing Points.................................................134Towing the Vehicle on Four Wheels......134
MaintenanceGeneral Information....................................135Opening and Closing the Bonnet...........135Under Bonnet Overview - 2.5L
Duratec-HE (122kW/165PS) -MI4..................................................................137
Under Bonnet Overview - 2.2LDuratorq-TDCi (Puma) Diesel............139
Under Bonnet Overview - 3.2LDuratorq-TDCi (Puma) Diesel.............141
Engine Oil Dipstick - 2.5L Duratec-HE(122kW/165PS) - MI4.............................143
Engine Oil Dipstick - 2.2L Duratorq-TDCi(Puma) Diesel/3.2L Duratorq-TDCi(Puma) Diesel...........................................143
Engine Oil Check...........................................143Engine Coolant Check................................144Power Steering Fluid Check......................145Brake and Clutch Fluid Check..................145Draining the Fuel Filter Water Trap........145Washer Fluid Check.....................................146Technical Specifications...........................146
Vehicle CareCleaning the Exterior...................................150Cleaning the Interior....................................150Repairing Minor Paint Damage.................151
Vehicle batteryJump-Starting the Vehicle........................152Battery connection points.........................153Battery warning symbols...........................153
Wheels and TyresGeneral Information....................................154Changing a Road Wheel............................154Tyre Care.........................................................160
3
Table of Contents
Using Winter Tyres.......................................160Using Snow Chains.......................................161Technical Specifications.............................161
Vehicle identificationVehicle Identification Plate.......................162Vehicle Identification Number.................162
Capacities and Specific-ations
Technical Specifications............................163
Navigation introductionGeneral Information......................................171Road Safety......................................................171
Navigation Quick startNavigation Quick start.................................173
Navigation unit overviewNavigation unit overview............................174Loading the navigation data.....................176
System settingsSystem settings.............................................177
Navigation systemRoute options menu...................................180Route displays................................................181
Traffic Message ChannelPrinciple of Operation.................................182Using TMC.......................................................182
Map updatesMap updates..................................................183
Audio introductionImportant audio information...................184
Audio unit overviewAudio unit overview.....................................185
Audio system securitySecurity code.................................................192
Audio unit clock and datedisplays
Setting the clock on the audio unit........193
Audio unit operationOn/off control................................................195Sound button.................................................195Waveband button........................................195Station tuning control.................................195Station preset buttons...............................196Autostore control.........................................196Traffic information control.......................196
Audio unit menusAutomatic volume control........................198Digital signal processing (DSP)..............198News broadcasts.........................................198Alternative frequencies..............................198Regional mode (REG)................................199
Compact disc playerCompact disc playback............................200Track selection.............................................200Fast forward/reverse.................................200Shuffle/random...........................................200Repeat compact disc tracks...................200Compact disc track scanning..................201MP3 file playback.........................................201MP3 display options...................................203Ending compact disc playback..............204
4
Table of Contents
Auxiliary input (AUX IN)socket
Auxiliary input (AUX IN) socket.............205
Audio system careAntenna..........................................................206
Audio troubleshootingAudio troubleshooting...............................207
TelephoneGeneral Information...................................208Telephone setup..........................................208Bluetooth setup...........................................209Telephone controls......................................210Using the telephone....................................210
Voice controlPrinciple of Operation.................................213Using voice control.......................................213Audio unit commands................................214Telephone commands...............................222Climate control commands.....................227
ConnectivityGeneral Information...................................229Connecting an external device...............230Connecting an external device - Vehicles
With: Bluetooth........................................230Using a USB device......................................231Using an iPod.................................................233
AppendicesType approvals.............................................235Type approvals.............................................235Type approvals.............................................235Electromagnetic compatibility...............235
5
Table of Contents
ABOUT THIS MANUALThank you for choosing Ford. Werecommend that you take some time toget to know your vehicle by reading thismanual. The more that you know about it,the greater the safety and pleasure youwill get from driving it.
WARNINGAlways drive with due care andattention when using and operatingthe controls and features on your
vehicle.
Note: This manual describes productfeatures and options available throughoutthe range, sometimes even before they aregenerally available. It may describe optionsnot fitted to your vehicle.Note: Some of the illustrations in thismanual may be used for different models,so may appear different to your vehicle.However, the essential information in theillustrations is always correct.Note: Always use and operate your vehiclein line with all applicable laws andregulations.Note: Pass on this manual when sellingyour vehicle. It is an integral part of thevehicle.This vehicle has received the endorsementof TÜV, the accredited international testingorganisation, for its allergy-friendlyproperties.All materials used in the manufacture ofthe interior of this vehicle meet strictrequirements of the TÜV TOXPROOFCriteria Catalogue for Vehicle Interiors byTÜV Produkt and Umwelt GmbH and aredesigned to minimize the risk of allergicreactions.
Additionally an efficient pollen filterprotects the passengers against allergenparticles in the outdoor air.For more information, contact TÜV atwww.tuv.com.
SYMBOLS GLOSSARYSymbols in this handbook
WARNINGYou risk death or serious injury toyourself and others if you do notfollow the instructions highlighted
by the warning symbol.
CAUTIONYou risk damaging your vehicle if youdo not follow the instructionshighlighted by the caution symbol.
Symbols on your vehicle
When you see these symbols, read andfollow the relevant instructions in thishandbook before touching or attemptingadjustment of any kind.
7
Introduction
PARTS AND ACCESSORIESGenuine Ford parts and accessories havebeen designed specifically for your vehicle.Unless we have specifically stated, wehave not tested non-Ford parts andaccessories and, therefore, we will notguarantee that they are suitable for yourvehicle. We recommend that you ask yourFord Dealer for advice on parts andaccessories suitable for your vehicle.
8
Introduction
Instrument panel overview - Left-hand drive
CA BGFEDHIJ
N MPOLK X QRVTS U SWE131277
Door lock button. See Lockingand Unlocking (page 29).
A
Audio unit. See Audio unitoverview (page 185).
B
Multi-functional display.C
Multi-function lever: Directionindicators. See DirectionIndicators (page 45). MainBeam. See Lighting Control(page 41). or Wiper lever. SeeWipers and Washers (page38).
D
Audio control. See AudioControl (page 36).
E
10
At a Glance
Instrument cluster. See Gauges(page 56). See Warning Lampsand Indicators (page 56).
F
Multi-function lever: Directionindicators. See DirectionIndicators (page 45). MainBeam. See Lighting Control(page 41). or Wiper lever. SeeWipers and Washers (page38).
G
Exterior mirror control. SeeElectric exterior mirrors (page54).
H
Headlamp levelling switch. SeeHeadlamp Levelling (page 44).
I
Air vents. See Air Vents (page66).
J
Bonnet release lever. SeeOpening and Closing theBonnet (page 135).
K
Driver side storagecompartment. See Storagecompartments (page 81).
L
Cruise control. See CruiseControl (page 109).
M
Ignition switch. See IgnitionSwitch (page 84).
N
Horn.ODriver knee airbag. See Principleof Operation (page 22).
P
Stability control (ESP) switch.See Using Stability Control(page 100).
Q
Passenger airbag deactivationwarning lamp. See Disablingthe passenger airbag (page25).
R
Auxiliary power sockets. SeeAuxiliary Power Points (page80).
S
Climate controls. See ManualClimate Control (page 66).
T
Auxiliary input and USB. SeeAuxiliary input (AUX IN)socket (page 82). See USBport (page 82).
U
Hazard warning flasher switch.See Hazard Warning Flashers(page 44).
V
Electronic Locking Differential(ELD) button. See Four-WheelDrive (page 92).
W
Hill descent control. See Hilldescent control (HDC) (page98).
X
Locking and unlockingUnlocking the vehicle
A
B
C
E131278
Key fold/unfold buttonAUnlockBLockC
Press the unlock button once to unlock thevehicle.
11
At a Glance
Press the lock button once to activatecentral locking.Press the lock button twice within threeseconds to double lock the doors.
Adjusting the steering wheelWARNING
Never adjust the steering wheelwhen the vehicle is moving.
2
1
E131279
WARNINGMake sure that you fully engage thelocking lever when returning it to itsoriginal position.
3E131280
See Adjusting the Steering Wheel (page36).
Manual climate controlRecommended settings for cooling
01 2 3
4
E131281
Select the outside air.Open the centre and side air vents.Direct the centre air vents upwards and theside air vents toward the side windows.
12
At a Glance
Recommended settings for heating
01 2 3
4
E131282
Select the outside air.Close the centre air vents and open theside air vents.Direct the side air vents toward the sidewindows.See Manual Climate Control (page 66).
Automatic climate controlRecommended settings for cooling
E131283
Select the outside air.Set the temperature to 22°C (72°F).Open the centre and side air vents.Direct the centre air vents upwards and theside air vents toward the side windows.
Recommended settings for heating
E131284
Select the outside air.Set the temperature to 22°C (72°F).Open the centre and side air vents.Direct the centre air vents upwards and theside air vents toward the side windows.
Direction indicators
B
A
E131285
If the lever is tapped up or down, thedirection indicators will flash three time.See Direction Indicators (page 45).
13
At a Glance
Airbag
E131289
WARNINGTo avoid the risk of death or seriousinjury, never use a rearward facingchild restraint in the front, unless the
air bag is OFF.
See Child Seat Positioning (page 17).
Manual transmissionSelecting reverse gear - 6 speed
E131287
It is necessary to raise the collar whilstselecting reverse gear in 6-speed vehicles.
See Manual Transmission (page 92).
RefuellingWARNING
Take care when refuelling to avoidspilling any residual fuel from the fuelpipe nozzle.
E135239
Insert the fuel pipe nozzle up to the firstnotch on the nozzle, and keep it in positionon the fuel filler opening.
WARNINGWe recommend that you wait atleast 10 seconds before removing thefuel nozzle to allow any residual fuel
to drain into the fuel tank.
E135240
Slightly raise the fuel nozzle to remove it.
14
At a Glance
CHILD SEATS
E133140
E68916
WARNINGSSecure children that are less than150 centimetres (59 inches) tall in asuitable, approved child restraint, in
the rear seat.Extreme Hazard! Do not use arearward facing child restraint on aseat protected by an air bag in front
of it!Read and follow the manufacturer’sinstructions when you are fitting achild restraint.Do not modify child restraints in anyway.Do not hold a child on your lap whenthe vehicle is moving.
WARNINGSDo not leave unattended children inyour vehicle.If your vehicle has been involved inan accident, have the child restraintschecked by properly trained
technicians.
Note: Mandatory use of child restraintsvaries from country to country.Only child restraints certified toECE-R44.03 (or later) have been testedand approved for use in your vehicle. Achoice of these are available from yourDealer.
Child restraints for different massgroupsUse the correct child restraint as follows:
Baby safety seat
E68918
Secure children that weigh less than 13kilograms (29 pounds) in a rearward facingbaby safety seat (Group 0+) in the rearseat.
16
Child Safety
Child safety seat
E68920
Secure children that weigh between 13 and18 kilograms (29 and 40 pounds) in a childsafety seat (Group 1) in the rear seat.
CHILD SEAT POSITIONING
WARNINGSPlease consult your Dealer for thelatest details relating to Fordrecommended child seats.
WARNINGSExtreme Hazard! Do not use arearward facing child restraint on aseat protected by an air bag in front
of it!When using a child seat with asupport leg, the support leg mustrest securely on the floor.When using a child seat with a seatbelt, make sure that the seat belt isnot slack or twisted.
CAUTIONThe child seat must rest tightlyagainst the vehicle seat. It may benecessary to lift or remove the head
restraint. See Head Restraints (page 76).
Note: When using a child seat on a frontseat, always adjust the front passenger seatto its fully rearwards position. If it provesdifficult to tighten the lap section of the seatbelt without slack remaining, adjust theseatback to the fully upright position andraise the height of the seat. See Seats(page 72).
Mass group categories
Seating positions 3210+0
22 - 36 kg15 - 25 kg9 - 18 kgUp to 13 kgUp to 10 kg
UF¹UF¹UF¹XXFront outboardpassenger seat withairbag ON
U¹U¹U¹U¹U¹Front outboardpassenger seat withairbag OFF
UUUUURear seats
XXXXXSingle cab center seat
X Not suitable for children in this mass group.
17
Child Safety
U Suitable for universal category child seats approved for use in this mass group.U¹ Suitable for universal category child seats approved for use in this mass group. However,we recommend that you secure children in a government approved child seat, in the rearseat.UF¹ Suitable for universal category forward facing child seats approved for use in thismass group. However, we recommend that you secure children in a government approvedchild seat, in the rear seat.
ISOFIX child seats - Double cab
Mass group categories
Seating positions10+
Forward facingRear facing
9 - 18 kgUp to 13 kg
Not ISOFIX equippedSize classFront seat
Seat type
A, B, B1, C, D*E, D, C*Size classRear outboard seat ISOFIX
IL, IUF***IL**Seat type
Not ISOFIX equippedSize classRear centre seat
Seat type
IL Suitable for particular ISOFIX child restraints systems of the semi-universal category.Please consult child restraints systems suppliers' vehicle recommendation lists.IUF Suitable for ISOFIX forward facing child restraints systems of universal categoryapproved for use in this mass group and ISOFIX size class.*The ISOFIX size class for both universal and semi-universal child restraints systemsis defined by the capital letters A to G. These identification letters are displayed on ISOFIXchild restraints.**At time of publishing the recommended Group O+ ISOFIX baby safety seat is the BritaxRoemer Baby Safe. Please consult your Dealer for the latest details relating to Fordrecommended child seats.***At time of publishing the recommended Group 1 ISOFIX child seat is the Britax RoemerSafefix PLUS. Please consult your Dealer for the latest details relating to Fordrecommended child seats.
18
Child Safety
ISOFIX ANCHOR POINTS
WARNINGUse an anti-rotation device whenusing the ISOFIX system. Werecommend that you use a top tether
or a support leg.
Note: When you are purchasing an ISOFIXrestraint, make sure that you know thecorrect mass group and ISOFIX size classfor the intended seating locations. SeeChild Seat Positioning (page 17).Your vehicle is fitted with ISOFIX anchorpoints that accommodate universallyapproved ISOFIX child restraints.The ISOFIX system comprises two rigidattachment arms on the child restraint thatattach to anchor points on the 2nd rowseats, where the cushion and backrestmeet. Tether anchor points are fitted tothe back panel trim for child restraints witha top tether.
Attaching a child restraint with atop tether
WARNINGDo not attach a tether strap toanything other than the correcttether anchor point.
Double cab
E136844
E132631
1. Remove the head restraint. See HeadRestraints (page 76).
2. Place the child seat on the back seatcushion and fold the relevant seatbackforward. See Rear Seats (page 76).
3. Route the tether strap to the anchorpoint.
WARNINGMake sure the top tether strap is notslack or twisted and is properlylocated on the anchor point.
19
Child Safety
4. Push the seatback to the uprightposition.
WARNINGSMake sure that the seatback issecure and fully engaged in thecatch.Make sure the safety seat is fittedcorrectly. There is a risk of injury.
5. Push the child seat back firmly toengage the ISOFIX lower anchor points.
6. Tighten the tether strap in line with thechild seat manufacturers instructions.
We recommend that you use a tether strapwhere fitted.
BOOSTER SEATS
WARNINGSDo not install a booster seat or abooster cushion with only the lapstrap of the seat belt.Do not install a booster seat or abooster cushion with a seat belt thatis slack or twisted.Do not put the seat belt under yourchild’s arm or behind its back.Do not use pillows, books or towelsto boost your child’s height.Make sure that your children sit in anupright position.Secure children that weigh morethan 15 kilograms (33 pounds) butare less than 150 centimetres (59
inches) tall in a booster seat or a boostercushion.
CAUTIONWhen using a child seat on a rear seat,make sure that the child seat reststightly against the vehicle seat. It may
be necessary to lift or remove the headrestraint. See Head Restraints (page 76).
Booster seat (Group 2)
E70710
We recommend that you use a boosterseat that combines a cushion with abackrest instead of a booster cushion only.The raised seating position will allow youto position the shoulder strap of the adultseat belt over the centre of your child’sshoulder and the lap strap tightly acrossits hips.
20
Child Safety
Booster cushion (Group 3)
E68924
CHILD SAFETY LOCKS
E132612
WARNINGYou cannot open the doors frominside if you have put the child safetylocks on.
Left-hand sideTurn anti-clockwise to lock and clockwiseto unlock.
Right-hand sideTurn clockwise to lock and anti-clockwiseto unlock.
21
Child Safety
PRINCIPLE OF OPERATIONAirbags
WARNINGSDo not modify the front of yourvehicle in any way. This couldadversely affect deployment of the
airbags.Original text according to ECER94.01: Extreme Hazard! Do not usea rearward facing child restraint on
a seat protected by an airbag in front of it!Wear a seat belt and keep sufficientdistance between yourself and thesteering wheel. Only when you use
the seat belt properly, can it hold you in aposition that allows the airbag to achieveits optimum effect. See Sitting in theCorrect Position (page 72).
Have repairs to the steering wheel,steering column, seats, airbags andseat belts carried out by a properly
trained technician.Keep the areas in front of the airbagsfree from obstruction. Do not affixanything to or over the airbag covers.Do not poke sharp objects into areaswhere airbags are fitted. This coulddamage and adversely affect
deployment of the airbags.Use seat covers designed for seatswith side airbags. Have these fittedby a properly trained technician.
Note: You will hear a loud bang and see acloud of harmless powdery residue if anairbag deploys. This is normal.Note: Only wipe airbag covers with a dampcloth.
Driver and front passenger airbags
E74302
The driver and front passenger airbags willdeploy during significant frontal collisionsor collisions that are up to 30 degrees fromthe left or the right. The airbags will inflatewithin a few thousandths of a second anddeflate on contact with the occupants,thus cushioning forward body movement.During minor frontal collisions, overturns,rear collisions and side collisions, the driverand front passenger airbags will notdeploy.
Driver knee airbag
CAUTIONDo not attempt to open the driverknee airbag cover.
The driver knee airbag will deploy duringfrontal collisions or collisions that are upto 30 degrees from the left or the right. Theairbag will inflate within a few thousandthsof a second and deflate on contact withthe occupants, thus providing a cushionbetween the driver’s knees and the steeringcolumn. During overturns, rear collisionsand side collisions, the knee airbag will notdeploy.For item location: See At a Glance (page9).
22
Occupant protection
Note: The knee airbag has a lowerdeployment threshold than the frontairbags. During a minor collision, it ispossible that only the knee airbag deploys.
Side airbags
E72658
Side airbags are fitted inside the seatbackof the front seats. A label indicates thatside airbags are fitted to your vehicle.The side airbags will deploy duringsignificant lateral collisions. The airbagswill inflate within a few thousandths of asecond and deflate on contact with theoccupants, thus providing protection forthe chest and shoulder areas. During minorlateral collisions, overturns, front collisionsand rear collisions, the side airbags will notdeploy.
Curtain airbags
E75004
Curtain airbags are fitted inside the trimpanels over the front and rear sidewindows. Moulded badges in the B-pillartrim panels indicate that curtain airbagsare fitted to your vehicle.The curtain airbags will deploy duringsignificant lateral collisions. The airbag willinflate within a few thousandths of asecond and deflate on contact with theoccupants, thus providing protection forthe head. During minor lateral collisions,front collisions, rear collisions, or overturnsthe curtain airbags will not deploy.
Seat beltsWARNINGS
Wear a seat belt and keep sufficientdistance between yourself and thesteering wheel. Only when you use
the seat belt properly, can it hold you in aposition to achieve its optimum effect. SeeSitting in the Correct Position (page72).
Never use a seat belt for more thanone person.Use the correct buckle for each seatbelt.Do not use a seat belt that is slackor twisted.Do not wear thick clothing. The seatbelt must fit tightly around your bodyto achieve its optimum effect.Position the shoulder strap of theseat belt over the centre of yourshoulder and position the lap strap
tightly across your hips.
23
Occupant protection
The driver and front passenger seat beltretractors are fitted with a seat beltpretensioner. Seat belt pretensioners havea lower deployment threshold than theairbags. During minor collisions, it ispossible that only the seat beltpretensioners will deploy.
Status after a collision
WARNINGSeat belts subjected to strain, as aresult of an accident, should berenewed and the anchorages
checked by a properly trained technician.
FASTENING THE SEAT BELTS
WARNINGInsert the tongue into the buckle untilyou hear a distinct click. You havenot fastened the seat belt properly
if you do not hear a click.
E74124
E85817
Pull the belt out steadily. It may lock if youpull it sharply or if the vehicle is on a slope.Press the red button on the buckle torelease the belt. Let it retract completelyand smoothly.
SEAT BELT HEIGHTADJUSTMENT
E131388
To raise or lower, pull the locking buttonon the adjuster and move as necessary.
24
Occupant protection
SEAT BELT REMINDER
WARNINGThe occupant protection system willonly provide optimum protectionwhen you use the seat belt properly.
Type 1: The seat belt warning lamp will beilluminated for 6 seconds when the ignitionis turned on to remind the driver to fastenthe seatbelt.Type 2: The seat belt warning lamp willbe illuminated at any time when the driversseat belt is not fastened.Type 3: The seat belt reminder warninglamp illuminates and an audible warningwill sound if the driver or front passengerseat belt has not been fastened and thevehicle exceeds a relatively low speed. Itwill also illuminate if either of the seat beltis unfastened when the vehicle is moving.The audible warning will go off after fiveminutes but the seat belt reminder warninglamp will remain on until the seat belt isfastened.
Deactivating the seat beltreminderSee your dealer.
USING SEAT BELTS DURINGPREGNANCY
E68587
WARNINGPosition the seat belt correctly foryour safety and that of your unbornchild. Do not use only the lap strap
or the shoulder strap.
Position the lap strap comfortably acrossyour hips and low beneath your pregnantabdomen. Position the shoulder strapbetween your breasts, above and to theside of your pregnant abdomen.
DISABLING THE PASSENGERAIRBAG
WARNINGMake sure that the passenger airbagis disabled when using a rearwardfacing child restraint on the front
passenger seat.
25
Occupant protection
E131289
Fitting the passenger airbagdeactivation switch
WARNINGIf you need to fit a child restraint ona seat protected by an operationalairbag in front of it and the vehicle is
not equipped with a passenger airbagdeactivation switch, have one fitted. Askyour dealer for further information.
Note: The key switch is located in the glovecompartment with an airbag deactivationlamp in the instrument panel.If the airbag warning lamp illuminates orflashes when you are driving, this indicatesa malfunction. Remove the child restraintand have the system checked immediately.
Disabling the passenger airbagNote: The passenger airbag ON and OFFwarning lamps will come on briefly whenthe ignition is switched on to confirm thatthe system is operational.
A B
PASS
ENGER AIRBAG
E136174
DisabledAEnabledB
Turn the switch to position A.
E137972
When you switch the ignition on,the passenger airbag OFFwarning lamp illuminates
indicating that the passenger airbag isdisabled. For item location: See At aGlance (page 9).
Enabling the passenger airbagWARNING
Make sure that the passenger airbagis enabled when you are not using achild restraint on the front passenger
seat.
Turn the switch to position B.
E137973
When you switch the ignition on,the passenger airbag ONwarning lamp illuminates for 60
seconds indicating that the passengerairbag is enabled. For item location: SeeAt a Glance (page 9).
26
Occupant protection
GENERAL INFORMATION ONRADIO FREQUENCIES
CAUTIONSThe radio frequency used by yourremote control can also be used byother short distance radio
transmissions (e.g. amateur radios,medical equipment, wireless headphones,remote controls and alarm systems). If thefrequencies are jammed, you will not beable to use your remote control. You canlock and unlock the doors with the key.
Check your vehicle is locked beforeleaving it unattended. This willsafeguard against any potential
malicious frequency blocking.
Note: You could unlock the doors if youpress the buttons on the remote controlunintentionally.The operating range between your remotecontrol and your vehicle varies dependingon the environment.
PROGRAMMING THE REMOTECONTROLNote: Additional remote controls can beprogrammed only if the vehicle is suppliedwith atleast one remote control.A maximum of eight remote controls(including the one supplied with yourvehicle) can be programmed. The remotecontrols must remain inside the vehicleduring the programming procedure. Fastenthe front seat belts and close all doors toensure that conflicting chimes do notsound during programming.
Programming a new remotecontrol1. To programme new remote controls
turn the ignition key to position II fourtimes within six seconds.
2. Turn the ignition to position 0. A tonesounds to indicate that it is nowpossible to programme the remotecontrols for ten seconds.
3. Press any button on a new remotecontrol. A tone will sound asconfirmation.
4. Repeat this last step for all your remotecontrols, including your original. Do notremove the key from the ignition whenpressing the button on this remotecontrol.
5. Switch the ignition back on (positionII) or wait for ten seconds withoutprogramming another remote controlto end the key programming. Only theremote controls which you have justprogrammed are now able to lock andunlock the vehicle.
Reprogramming the unlockingfunctionNote: When you press the unlock buttoneither all the doors are unlocked or only thedriver’s door is unlocked. Pressing the unlockbutton again unlocks all the doors.Press and hold the unlock and lock buttonson the remote key simultaneously for atleast four seconds with the ignition off. Thedirection indicators will flash twice toconfirm the change.To return to the original unlocking function,repeat the process.
Programming the additional keyNote: The additional keys can beprogrammed only if you already have twoprogrammed keys.
27
Keys and Remote Controls
1. Insert the first key and switch on theignition.
2. Remove the key within 10 seconds.3. Insert the second key within 10 seconds
and switch on the ignition.4. Remove the key within 10 seconds.5. Insert the additional key within 10
seconds which need to beprogrammed.
CHANGING THE REMOTECONTROL BATTERY
E107998
Make sure that you dispose ofold batteries in anenvironmentally friendly way.
Seek advice from your local authorityregarding recycling.
E1288092
1
1. Insert a screwdriver in the position shownand gently push the clip.2. Press the clip down to release thebattery cover.
E128810
3. Carefully remove the cover.
E128811
4. Turn the remote control over to removethe battery.5. Install a new battery (3V CR 2032) withthe + facing upwards.6. Replace the battery cover.
28
Keys and Remote Controls
LOCKING AND UNLOCKINGNote: Do not leave your keys in the vehicle.Note: All the doors will lock automaticallywhen the vehicle is driven at or above 7Km/h (4.3 mph). This function can beenabled or disabled, see driverconfiguration mode later in this procedure.
Locking and unlocking the doorswith the key
A
B
A
B
A
B
E131447
UnlockALockB
Note: To double lock the doors, turn thekey to the lock position twice within threeseconds.
Locking and unlocking the doorswith the remote controlAutomatic relocking: The doors willrelock automatically if you do not open adoor within 45 seconds of unlocking thedoors with the remote control. The doorlocks and the alarm will return to theirprevious state.Note: This option can be switched off byyour Ford dealer.
A
B
C
E131278
Key fold/unfold buttonAUnlockBLockC
Press the button B once to unlock thevehicle.Press the button C once to activate centrallocking.Note: Central locking is activated only whenall the passenger doors are closed.Press the button C twice within fourseconds to double lock the doors.
29
Locks
Note: Double locking is activated only whenall the passenger doors are closed and thebonnet is closed in the vehicle fitted withalarm.
WARNINGDo not activate double locking whenpersons or animals are inside thevehicle. You will not be able to
unlock the doors from inside if you havedouble locked them.
Note: If the ignition is switched on with thedouble locking function activated, the lockwill automatically return to single lock stage.Double locking is a theft protection featurethat prevents someone from opening thedoors from the inside.Note: The driver’s door can be unlockedwith the key. This needs to be used if theremote control is not functioning.Note: If the vehicle remains locked forseveral weeks, the remote control will bedisabled. The vehicle must be unlocked andthe engine started using the key. Unlockingand starting the vehicle once will enable theremote control.
Reprogramming the unlocking functionThe unlocking function may bereprogrammed so that only the driver’sdoor is unlocked. See Programming theremote control (page 27).
Locking and unlocking confirmationNote: When you lock the doors, thedirection indicators will flash once.When you double lock the doors, thedirection indicators will flash twice.When you unlock the doors the directionindicators will flash one long flash.
Child play protection functionIf the remote control buttons are pressedcontinuously several times, the locking andunlocking function will be blocked for awhile to avoid door latches fromoverheating.
Locking and unlocking the doorsfrom inside
E131288
Press the button. For itemlocation. See At a Glance (page9).
Driver configuration modeNote: This operation has to be done within30 seconds.1. Ignition OFF to ON position.2. Press central lock/unlock button 3
times.3. Ignition ON to OFF position.4. Press central lock/unlock button 3
times.5. Ignition OFF to ON position.The system will chirp to indicate that thedriver configuration mode is enabled.
Automatic locking by speedPress the central lock/unlock button twicewithin three seconds to toggle theautomatic locking by speed function. Thesystem will chirp when toggling.
Automatic unlockingNote: Automatic unlock is default enabled.Press the button three time within threeseconds to toggle the automatic unlockingfunction.If the automatic unlocking function isenabled:
30
Locks
• All doors will be unlocked whileopening the driver door or frontpassenger door (vehicles not deliveredwith remote control) from inside, withthe key in ignition.
If the automatic unlocking function isdisabled:• Only the respective door will be
unlocked while opening from inside.Note: Opening the rear doors will neverunlock the other doors, when opened frominside.
Locking the doors individually withthe keyNote: If the central locking function fails tooperate, the doors can be individually lockedusing the key in the position shown.
E131448
Left-hand sideTurn clockwise to lock.
Right-hand sideTurn anti-clockwise to lock.
UnlockingNote: If the child safety locks have alsobeen activated, pulling the internal lever willonly deactivate the emergency locking andnot the child safety lock. The doors can onlybe opened using the external door handle.Note: If the doors have been unlocked, theyhave to be locked individually using thismethod until the central locking functionhas been repaired.Unlock the driver's door using the key. Theother doors can be unlocked individually bypulling the interior door handles on thosedoors.
GLOBAL OPENING ANDCLOSINGNote: You can operate the windows for upto one minute after you switch off theignition. They will be deactivated as soonas a door is opened.Note: Global closing will only operate if youhave set the memory correctly for eachwindow. See Power Windows (page 52).
Global opening
E134622
31
Locks
To open all the windows, press and holdthe remote control unlock button for atleast three seconds. Press any remotecontrol button again to stop the openingfunction.
Global closingWARNING
Take care when using global closing.In an emergency, press a buttonimmediately to stop the windows.
E134623
To close all the windows, press and holdthe remote control lock button for at leasttwo seconds. Press any remote controlbutton again to stop the closing function.The anti-trap function is also active duringglobal closing.
32
Locks
PRINCIPLE OF OPERATIONThe engine immobiliser is a theft protectionsystem that prevents someone fromstarting the engine with an incorrectlycoded key.
CODED KEYSNote: Do not shield your keys with metalobjects. This may prevent the receiver fromrecognising your key as a valid one.Note: Have all of your remaining keyserased and recoded if you lose a key. Askyour dealer for further information. Havereplacement keys recoded together withyour existing keys.If you lose a key, you can obtain areplacement from your Ford Dealer. Ifpossible, provide them with the keynumber from the tag provided with theoriginal keys. You can also obtainadditional keys from your Ford Dealer.
ARMING THE ENGINEIMMOBILISERThe engine immobiliser is armedautomatically a short time after you haveswitched the ignition off.The indicator in the instrument cluster willflash to confirm that the system isoperating.
DISARMING THE ENGINEIMMOBILISERThe engine immobiliser is disarmedautomatically when you switch the ignitionon with a correctly coded key.
The indicator in the instrument cluster willcome on for approximately three secondsand then go out. If the indicator stays onfor one minute or flashes for approximatelyone minute and then repeatedly at irregularintervals, your key has not been recognised.Remove the key and try again.If you are unable to start the engine with acorrectly coded key, this indicates amalfunction. Have the immobiliser checkedimmediately.
33
Engine immobiliser
PRINCIPLE OF OPERATIONAlarm systemYour vehicle may be equipped with one ofthe following alarm systems:• Perimeter alarm with interior sensors.• Perimeter alarm with interior sensors
and battery back-up sounder.
Interior sensors
E133698
The interior sensors are activated whenyou arm the alarm. See Arming the alarm(page 35).
WARNINGSThe sensors in the interior lamp unitmust not be covered up. Do notactivate the alarm if any persons,
animals or other moving objects are insidethe vehicle.
The interior sensors may not detectmovement with in the cab correctlyif the rear seat base in the double
cab is left in the upright position.Do not leave the glasses holder open.
Note: This may result in false alarms ifanimals or moving objects are inside thevehicle.Note: False alarms can also be triggeredby the fuel fired heater. If you are using thefuel fired heater, direct the air flow towardsthe footwell.
The sensors act as a deterrent againstunauthorised intrusion by sensing anymovement within the vehicle.
Alarm HornThe alarm horn will sound a siren when thealarm is triggered. It is armed when youlock the vehicle. This will not sound ifsomeone disconnects the vehicle batteryor the alarm horn itself.
Battery back-up sounderThe battery back-up sounder is an extraalarm system which will sound a sirenwhen the alarm is triggered. It is armedwhen you lock the vehicle. The sounderhas its own battery and will sound analarm siren even if someone disconnectsthe vehicle battery or the battery back-upsounder itself.
Triggering the alarmOnce armed, the alarm is triggered in anyof the following ways:• If someone opens a door or the bonnet
without a valid key or remote control.• If someone removes the multi function
display.• If the ignition is turned to position I, II
or III without a valid key.• If the interior sensors detect movement
within the vehicle.• On vehicles with a battery back-up
sounder, if someone disconnects thevehicle battery or the battery back-upsounder itself.
If the alarm is triggered, the alarm horn willsound for 30 seconds and the hazardwarning flasher will flash for five minutes.Any further attempts to perform one of theabove will trigger the alarm again.
34
Alarm
ARMING THE ALARMTo arm the alarm, lock the vehicle. SeeLocks (page 29).
DISARMING THE ALARMDisarm and silence the alarm by unlockingthe doors with the key and inserting thekey into the ignition switch with a correctlycoded key within 12 seconds, or unlockingthe doors with the remote control.
35
Alarm
ADJUSTING THE STEERINGWHEEL
WARNINGNever adjust the steering wheelwhen the vehicle is moving.
Note: Make sure that you are sitting in thecorrect position. See Sitting in the CorrectPosition (page 72).
2
1
E131279
3E131280
WARNINGMake sure that you fully engage thelocking lever when returning it to itsoriginal position.
AUDIO CONTROL
E72288
A
C
BD
E
Volume upASeek upBVolume downCSeek downDModeE
ModePress and hold the mode button to selectthe audio source.Press the mode button to:• tune the radio to the next preset
station• accept an incoming telephone call• end a telephone call.
SeekPress the seek button to:• tune the radio to the next station up or
down the frequency band• play the next or the previous CD track.
36
Steering Wheel
Press and hold the seek button to:• tune the radio up or down the
frequency band• seek through a CD track.
VOICE CONTROL
A
E136223
Voice controlA
E136747
Press the voice control buttonto select or deselect voicecontrol.
For further information: See Voice control(page 213).
37
Steering Wheel
WINDSCREEN WIPERS
CAUTIONOperating this function with theengine off will drain the battery.
CD
B
A
E131452
Single wipeAIntermittent wipe or autowipersBNormal wipeCHigh speed wipeD
Intermittent wipe
B
C
A
E131453
Long wipe intervalAIntermittent wipeBShort wipe intervalC
AUTOWIPERS
CAUTIONSDo not switch autowipers on in dryweather conditions. The rain sensoris very sensitive and the wipers may
operate if dirt, mist or flies hit thewindscreen.
Replace the wiper blades as soon asthey begin to leave bands of waterand smears. If you do not replace
them, the rain sensor will continue todetect water on the windscreen and thewipers will operate, even though themajority of the windscreen is dry.
Fully defrost the windscreen in icyconditions before you switchautowipers on.Switch autowipers off before youenter a car wash.
B
C
A
E131453
High sensitivityAOnBLow sensitivityC
If you switch autowipers on, the wipers willnot cycle until water is detected on thewindscreen. The rain sensor will thencontinuously measure the amount of wateron the windscreen and adjust the speedof the wipers automatically.
38
Wipers and Washers
Adjust the sensitivity of the rain sensorusing the rotary control. With lowsensitivity, the wipers will operate whenthe sensor detects a lot of water on thewindscreen. With high sensitivity, thewipers will operate if the sensor detects asmall amount of water on the windscreen.
WINDSCREEN WASHERS
CAUTIONOperating this function with theengine off will drain the battery.
E131460
WARNINGDo not operate the windscreenwashers for more than 10 secondsor when the reservoir is empty.
CHECKING THE WIPERBLADES
E66644
Run the tip of your fingers over the edge ofthe blade to check for roughness.Clean the wiper blade lips with waterapplied with a soft sponge.
CHANGING THE WIPERBLADESWindscreen wiper blades
CAUTIONSSet the windscreen wipers in theservice position to change the wiperblades.You can use the service position inwinter to provide easier access to thewiper blades for freeing them from
snow and ice. The windscreen wipers willreturn to their normal position as soon asyou switch on the ignition so make surethat the outside of the windscreen is freefrom snow and ice before you switch onthe ignition.
39
Wipers and Washers
Service position1. Turn the ignition key to position 0 from
position II.2. Pull the washer lever towards the
steering wheel within three seconds.
E93783
1
2
E93784
3
5
4
E93785
6
E93786
Note: Make sure that the wiper blade locksinto place.Install in the reverse order.
40
Wipers and Washers
LIGHTING CONTROLLighting control positions
A
BC
D
E133582
OffAAuto-light controlBHeadlampsCSide and tail lampsD
Parking lampsCAUTION
Prolonged use of the parking lampswill discharge the battery.
Switch off the ignition.
Both sidesSet the lighting control to position D.
One sideNote: The parking lamp has to be switchedon within 10 minutes from the key out. Ifexceeded, the key has to reinserted.
B
A
E131285
Right-hand sideALeft-hand sideB
Main and dipped beam
E133583
Push the lever forward to switch betweenmain and dipped beam.
Headlamp flasherPull the lever towards the steering wheel.
Home safe lightingSwitch the ignition off and pull thedirection indicator lever towards thesteering wheel or if you have switchedautolamps on, turn the key from positionII to I or 0 to switch the headlamps on.
41
Lighting
You will hear a short tone. The headlampswill go off automatically after threeminutes with any door open, or 30 secondsafter the last door has been closed.With all doors closed, but within the 30second delay, opening any door will resultin the three minute timer starting again.The home safe lights can be cancelled byeither pulling the direction indicator levertowards the steering wheel again or byturning the ignition switch on.
Approach lampsThe side repeaters and the puddle lampswill come on when the vehicle is unlockedwith the remote control.
Emergency stop lightsHazard warning flashers or fog lights willcome on when the brake is appliedsuddenly at a speed above 50 km/h (30mph).
AUTOLAMPS
WARNINGIn severe weather conditions, it maybe necessary to switch yourheadlamps on manually.
E133599
Note: If you have switched autolamps on,you can only switch the main beam on whenautolamps has switched the headlamps on.The headlamps will come on and go offautomatically depending on the ambientlight.
FRONT FOG LAMPSControl lever
E133585
WARNINGOnly use the front fog lamps whenvisibility is considerably restricted byfog, snow or rain.
Note: You cannot switch the front foglamps on unless you have switched theheadlamps on.
AdjustmentYou can adjust the front fog lamp aimingslightly for driving comfort.Note: Fog lamp adjustment must meet thelocal regulation requirements.
42
Lighting
X
E136853
E136854
1. Position the unloaded vehicle on a flat,level surface.
2. Seat one person in the driver’s seat.3. Start the engine so that the battery
remains charged.
4. Turn the front fog lamp on.5. Adjust the fog lamp aiming such that
the cut off line is not more than X: 20m (65.6 ft).
REAR FOG LAMPS
E136254
WARNINGSOnly use the rear fog lamps whenvisibility is restricted to less than 50metres (164 feet).Do not use the rear fog lamps whenit is raining or snowing and visibilityis more than 50 metres (164 feet).
Note: You cannot switch the rear fog lampson unless you have switched the headlampsand front fog lamp on.
43
Lighting
HEADLAMP LEVELLING
E78244
Without headlamp levellingAWith headlamp levellingB
You can adjust the level of the headlampbeams according to the vehicle load.
1
0
A
BE133544
Raised headlamp beamsALowered headlamp beamsB
Set the headlamp levelling control to zerowhen your vehicle is unloaded. Set it toprovide illumination between 35 and 100metres (114 and 328 feet) when yourvehicle is partially or fully loaded.
HAZARD WARNING FLASHERS
E71943
For item location: See At a Glance (page9).
44
Lighting
DIRECTION INDICATORS
B
A
E131285
Right-hand sideALeft-hand sideB
INTERIOR LAMPSCourtesy lamp
E112207
B CA
OffADoor contactBOnC
If you set the switch to position B, thecourtesy lamp will come on when youunlock or open a door. If you leave a dooropen with the ignition switch off, thecourtesy lamp will go off automaticallyafter some time to prevent the vehiclebattery from discharging. To switch it backon, switch on the ignition for a short time.
The courtesy lamp will also come on whenyou switch off the ignition. It will go offautomatically after a short time or whenyou start or restart the engine.If you set the switch to position C with theignition switch off, the courtesy lamp willcome on. It will go off automatically aftera short time to prevent the vehicle batteryfrom discharging. To switch it back on,switch on the ignition for a short time.
Reading lamps
E112208
If you switch off the ignition, the readinglamps will go off automatically after sometime to prevent the vehicle battery fromdischarging. To switch them back on,switch on the ignition for a short time.
CHANGING A BULB
WARNINGSSwitch the lights and the ignition off.
Let the engine compartment and thebulb cool down before removing it.
CAUTIONOnly fit bulbs of the correctspecification. See BulbSpecification Chart (page 51).
Note: The following instructions describehow to remove the bulbs. Fit replacementsin the reverse order unless otherwise stated.
45
Lighting
You may notice fogging or small waterdroplets in the lamp units from time totime. This does not affect the function ofthe lamp, and will clear when the lampsare turned on and the vehicle is driven.Note: If in any doubt about any of thefollowing bulb replacement procedures,please have the bulb replaced by yourAuthorised Ford Dealer.
Headlamp main and dipped beamCAUTIONS
Do not touch the glass of the bulb.
Ensure bulb is correctly seated beforereplacing the spring clip. Checking thebulb location through the front of the
headlamp lens can be a useful aid toensuring the bulb is correctly aligned.
4 3
2
E133679
1. Open the bonnet. See Opening andClosing the Bonnet (page 135).
2. Disconnect the electrical connector bypressing in the spring releases on bothsides of the connector.
3. Remove the rubber boot.4. Release the bulb retaining spring clip
and remove the bulb.5. Insert the replacement bulb and retain
it using the spring clip.
Note: Ensure that the rubber boot sealscorrectly against the bulb and headlighthousing and that it is not out of shape whileinstalling.
Side lamps and front directionindicators
2
A
B 1
E133680
Direction indicatorASide lampB
1. Remove the bulb holder from theheadlamp assembly.
2. Remove the bulb.
46
Lighting
Front fog lamps
E133681
1
23
Note: You cannot separate the bulb fromthe bulb holder.1. Disconnect the electrical connector.2. Turn the bulb holder anti-clockwise
and remove it.
Side repeaters
1
2
E133682
1. Slide the lens to the rear and removeit.
2. Disconnect the electrical connector.
Exterior mirror lamps
AB
E133683
Side repeater lampAPuddle lampB
Note: These are not serviceable items,please consult your dealer if they fail.
Rear lampsType 1
23
E133757
47
Lighting
A
B
C
D
45
E133684
Tail and brake lampADirection indicatorBReversing lampCFog lamp (left-hand side forLHD)
D
1. Open the tailgate.2. Remove the screws.3. Remove the rear lamp.4. Turn the bulb holder anti-clockwise
and remove it.5. Remove the bulb.
Type 2
CBA
1E133685
Direction indicatorATail and brake lampBReversing lampC
1. Remove the screws.2. Remove the lens.3. Remove the bulb.
Number plate lampType 1
1
2
3
E133686
1. Slide the unit away from the connectorand remove it.
48
Lighting
2. Remove the connector with bulb.3. Remove the bulb.
Type 2
123
E133687
1. Remove the screws.2. Remove the lens.3. Remove the bulb.
Interior lampStretch and double cab
E99452
2
3
1
1. Carefully prise out the lamp.2. Turn the bulb holder anti-clockwise
and remove it.3. Remove the bulb.
Front reading lamps
E99453
2
3
1
1. Carefully prise out the lamp.2. Turn the bulb holder anti-clockwise
and remove it.3. Remove the bulb.
Centre high mount stop lampType 1
1
2
E133689
49
Lighting
3
E133756
5 64
E133755
1. Remove the cover.2. Remove the screws.3. Carefully prise out the lamp.4. Disconnect the electrical connector.5. Remove the bulb holder by turning it
to 45 degree anticlockwise.6. Remove the bulbs.
Type 2
123E134135
4
56
E134136
1. Remove the cover.2. Remove the screws.3. Carefully prise out the lamp.4. Disconnect the electrical connector.5. Pull out the bulb holder.6. Remove the bulbs.
50
Lighting
BULB SPECIFICATION CHART
Power (watts)SpecificationBulb
55/60H4Headlamp main and dippedbeam
21P21WFront direction indicator
5W5WSide lamp
55H11Front fog lamp
5-Side repeater*
21WY21WRear direction indicator
21/5W21/5WTail and brake lamp
21W21WReversing lamp
21W21WRear fog lamp
5W5WNumber plate lamp
5W5WInterior lamp
5W5WReading lamp
5W5WCentre high mount stoplamp
5W5WRoof bar lamp
* Bulb replacement is not possible as thebulb is an integral part of the unit. The siderepeater lamp unit has to be changed.
51
Lighting
POWER WINDOWS
WARNINGDo not operate the electric windowsunless they are free from obstruction.
Note: If you operate the switches oftenduring a short period of time, the systemmight become inoperable for a certain timeto prevent damage due to overheating.Note: If you operate both the switch on therelevant door and the switch for thatwindow on the driver’s door at the sametime, the window will stop moving.Switch on the ignition to operate theelectric windows.
Driver’s door switches (Doublecab)You can operate all the windows with theswitches on the door trim panel of thedriver’s door.
A
B
E131466
OpenACloseB
Driver’s door switches (Single andStretch cab)
A
B
E131469
OpenACloseB
Front and rear passengers’ doorswitches
A
B
E131467
OpenACloseB
Opening and closing the windowsautomaticallyPress or lift the switch to the second actionpoint and release it. Press or lift it again tostop the window.
52
Windows and Mirrors
Safety switch for the rear windowsNote: You can always operate the rearwindows and front passenger window fromthe driver’s door if global opening andclosing is fitted.Note: Only vehicles with global openingand closing will have a light on the switchto indicate that it is active.
E131468
A switch in the driver’s door disables therear and front passenger electric windowswitches.The light in the safety switch comes on andthe lights in the rear window switches gooff when the rear windows are disabled.
Resetting the memory of theelectric windows
WARNINGThe anti-trap function is deactivateduntil you have reset the memory.
After the battery has been disconnectedfrom the vehicle you must reset thememory separately for each window:1. Lift the switch until the window is fully
closed. Hold the switch lifted for onemore second.
2. Release the switch and lift it again,until a click is heard from the relay, forone more second.
3. Open the window and try to close itautomatically.
4. Repeat the procedure if the windowdoes not close automatically.
Safety modeWARNING
The anti-trap function is not activeduring this procedure.
If the system detects a malfunction, itenters a safety mode. The windows willmove for only about 0.5 seconds at a timeand then stop again. Close the windowsby pressing the switch again when thewindows stop moving. Have this checkedimmediately.
Global opening and global closing(GO/GC) (If fitted)You can also operate the electric windowsfor one minute with the ignition off via theglobal opening and global closing function.See Global Opening and Closing (page31).Note: Global opening and global closingwill open or close the windowsautomatically only on vehicles equippedwith this feature.Note: Global closing will only operate if youhave set the memory correctly for eachwindow. Memory is set by default, you haveto reset it only if there is a problem.
Anti-trap function (vehicles withGO/GC only)
WARNINGCareless closing of the windows canoverride the protection function andcause injuries.
The electric windows will stopautomatically while closing (auto-up) andreverse some distance if there is anobstacle in the way.
53
Windows and Mirrors
Overriding the anti-trap function
CAUTIONWhile you close the window (auto-up)for the third time with the obstacle inthe way, the anti-trap function is
disabled. Make sure there are no obstaclesin the way of the closing window.
To override this protection function whenthere is a resistance, for example, in thewinter, proceed as follows:1. Close the window twice until it reaches
the resistance and let it reverse.2. Close the window a third time to the
resistance. The anti-trap function isdisabled and you cannot close thewindow automatically. The windowwill override the resistance and you canfully close it manually.
3. If the window does not close after thethird attempt, have it checked by aproperly trained technician.
EXTERIOR MIRRORS
WARNINGDo not overestimate the distance ofthe objects that you see in theconvex mirror. Objects seen in
convex mirrors will appear smaller andfurther away than they actually are.
Manual folding mirrorsFoldingPush the mirror towards the door windowglass.
UnfoldingMake sure that you fully engage the mirrorin its support when returning it to itsoriginal position.
ELECTRIC EXTERIORMIRRORS
WARNINGDo not overestimate the distance ofthe objects that you see in theconvex mirror. Objects seen in
convex mirrors will appear smaller andfurther away than they actually are.
A CB
E131480
Left-hand mirrorAOffBRight-hand mirrorC
E131481
54
Windows and Mirrors
The electric exterior mirrors are fitted witha heating element that will defrost ordemist the mirror glass. See HeatedWindows and Mirrors (page 71).
Electric folding mirrors
E131482
To fold and unfold the mirrors, briefly pressthe switch. If the switch is pressed againwhile the mirrors are moving, they will stopand reverse the direction of movement.
SLIDING WINDOWS
1
2
E133600
55
Windows and Mirrors
GAUGES
A B C D
F EGE131495
TachometerAFuel gaugeBEngine coolant temperaturegauge
C
SpeedometerDIllumination dimming buttonEInformation displayFTrip computer display select andreset button
G
Engine coolant temperature gaugeShows the temperature of the enginecoolant. At normal operating temperature,the needle will remain in the centre section.
CAUTIONDo not restart the engine until thecause of overheating has beenresolved.
If the needle enters the red section, theengine is overheating. Stop the engine,switch the ignition off and determine thecause once the engine has cooled down.See Engine Coolant Check (page 144).
Fuel gaugeThe arrow adjacent to the fuel pumpsymbol tells you on which side of yourvehicle the fuel filler cap is located.
WARNING LAMPS ANDINDICATORSThe following warning lamps andindicators will come on briefly when youswitch the ignition on to confirm that thesystem is operational:• ABS warning lamp• Vehicle immobiliser indicator• Brake system warning lamp• Ignition warning lamp• Airbag warning lamp• Low fuel level warning lamp• Stability control (ESP) indicator• Oil pressure warning lamp• Oil Change Reminder Indicator (Diesel
only)• Engine warning lamps• Four-wheel drive indicator• Four-wheel drive low (4L) indicator• Electronic locking differential (ELD)
indicator• Water-in-fuel indicator• Washer fluid level indicator• DPF (Diesel Particulate Filter)• Ice/Frost warning indicator
ABS warning lampIf it illuminates when you aredriving, this indicates amalfunction. You will continue
to have normal braking (without ABS).Have the system checked by a properlytrained technician as soon as possible.
56
Instrument Cluster
Vehicle immobiliser indicator
E131559
The immobiliser indicator willblink if the key is removed fromthe ignition or a wrong key is
inserted.
Brake system warning lampIt illuminates when the parkingbrake is engaged.
WARNINGReduce your speed gradually andstop your vehicle as soon as it is safeto do so. Use your brakes with care.
If it illuminates when you are driving, checkthat the parking brake is not engaged. Ifthe parking brake is not engaged, thisindicates a malfunction. Have the systemchecked by a properly trained technicianimmediately.
Ignition warning lampIf the ignition warning lampcomes on when you are driving,switch off all unnecessary
electrical equipment and have thischecked immediately Have this checkedby an expert.
Airbag warning lampIf it illuminates while driving, thisindicates a malfunction. Havethis checked as soon as possible.
Low fuel level warning lampIf the low fuel level warning lampcomes on, refuel as soon aspossible.
The arrow adjacent to the fuel pumpsymbol tells you on which side of yourvehicle the fuel filler cap is located.
Stability control (ESP) indicatorWhile driving, it flashes duringactivation of the system. Afterswitching on the ignition, if it
does not illuminate or illuminatescontinuously while driving, this indicates amalfunction. During a malfunction, thesystem switches off. Have the systemchecked by a properly trained technicianas soon as possible.
E131561
If you switch ESP off, thewarning lamp will flash twiceand remain illuminated. The
lamp will go out when you switch thesystem back on or when you switch theignition off.
Oil pressure warning lampCAUTION
Do not resume your journey if the oilpressure warning lamp comes ondespite the oil level being correct.
Have this checked immediately.
If the oil pressure warning lampcomes on when you are driving,this indicates a malfunction.
Stop, and switch the engine off and checkthe engine oil level. See Engine Oil Check(page 143).
Oil Change Reminder Indicator(Diesel only)
E131563
The oil change reminderindicator informs that the enginerequires an engine oil change
due to excessive build up of soot within theengine oil.
57
Instrument Cluster
Engine warning lampsMalfunction indicator lamp
Powertrain warning lamp
All vehiclesIf either lamp illuminates when the engineis running, this indicates a fault. The enginewill continue to run but it may have limitedpower. If it flashes when you are driving,reduce the speed of your vehicleimmediately. If it continues to flash, avoidheavy acceleration or deceleration. Havethe system checked by a properly trainedtechnician immediately.
WARNINGHave this checked immediately.
If both lamps illuminate together, stop yourvehicle as soon as it is safe to do so(continued use may cause reduced powerand cause the engine to stop). Turn theignition off and attempt to restart theengine. If the engine restarts have thesystem checked by a properly trainedtechnician immediately. If the engine doesnot restart the vehicle must be checkedbefore continuing your journey.
Four-wheel drive indicator
E131555
The four-wheel drive indicatorlamp will come on when thetransfer shift switch is in the 4H
or 4L position. This will flash whileengaging to 4H or 4L. See ElectronicLocking Differential (page 93).
Four-wheel drive low (4L)indicator
E92386
The four-wheel drive low (4L)indicator lamp will come onwhen the transfer shift switch is
in 4L position. It will flash while engagingto 4L position. See Electronic LockingDifferential (page 93).
Electronic locking differential(ELD) indicator
E131556
The ELD indicator lamp willcome on when the reardifferential is locked. The lamp
will flash if an error has been detected orif the engage or disengage request cannotbe completed. See Electronic LockingDifferential (page 93).
Water-in-fuel indicatorThe water-in-fuel indicator lampwill come on if there is excesswater in the fuel filter. Drain off
the water immediately. See Draining theFuel Filter Water Trap (page 145).
Washer fluid level indicator
E131557
It illuminates when thewindshield washer fluid levelgoes below the minimum mark.
See Washer Fluid Check (page 146).
DPF (Diesel Particulate Filter)
E95449
If this illuminates, have thesystem checked by a properlytrained technician as soon as
possible.
58
Instrument Cluster
Ice/Frost warning indicatorWARNING
Even if the temperature rises toabove +4°C (39°F) there is noguarantee that the road is free of
hazards caused by inclement weather.
E131558
It will illuminate and glow orangewhen the outside airtemperature is between 4°C and
0°C (39°F and 32°F). It will glow red whenthe temperature is below 0°C (32°F).
Door open warning lampThe door open warning lamp willcome on when you switch theignition on and if you have not
closed the doors properly.
Glow plug indicator - For Dieselvehicles
See Starting a Diesel Engine(page 85).
Direction indicatorsRight side turn indicator
Left side turn indicator
The direction indicator will flash when youuse the direction indicators. A suddenincrease in the rate of flashing warns of afailed bulb.
Headlamp indicatorThe headlamp indicator willcome on when you switch theside and tail lamps on.
Main beam indicatorThe main beam indicator willcome on when you switch theheadlamp main beam on. It will
flash when you use the headlamp flasher.
Front fog lamp indicatorThe front fog lamp indicator willcome on when you switch thefront fog lamps on.
Rear fog lamp indicatorThe rear fog lamp indicator lampwill come on when you switchthe rear fog lamps on.
Seat belt indicator
E131560
See Seat belt reminder (page25).
Gear shift indicator lamp (Manualonly)
It will illuminate to inform youthat shifting to a higher gear maygive better fuel economy and
lower CO2 emissions.
Cruise control
E71340
It will illuminate when you haveset a speed using the cruisecontrol system.
59
Instrument Cluster
AUDIBLE WARNINGS ANDINDICATORSDoor open warningThe door open warning chime will soundif the vehicle speed exceeds approximately10km/h (6.2 mph) and you have not closedthe doors.
Lights on warningThe lights on warning chime will sound ifyou the key is not in position II or III andopen any door before switching off thelights.
Not in park warningThe not in park warning chime will soundif the automatic transmission lever is notin park position and you open the driver'sdoor.
Parking brake warningThe parking brake warning chime willsound if the parking brake is left engagedand the vehicle speed exceedsapproximately 5 km/h (3 mph).
Restraints back-up warningThe restraints back-up warning chime willsound if there is a malfunction in therestraints warning lamp. 5 sets of 5 tonebursts will be heard every 30 minutes.
Low fuel level warningLow fuel level warning chime will soundwhen the low fuel level warning lamp isactivated and/or the information displayis showing 80, 40, 20, 0 km (50, 25, 10, 0miles) remaining.
Turn indicatorThe turn indicator chime will sound whenthe left or right turn indicator is activated.
Direction indicators warningThe direction indicator warning chime willsound if the left or right direction indicatoris left on and driven for more thanapproximately 3.2 km (1.98 miles).
One side park lightOne side park light chime will sound whenthe one side park light is activated.
Home safeHome safe warning chime will sound whenthe home safe lighting is activated.
Seat belt reminderThe seat belt warning chime will sound ifthe driver's and/or passenger's seat beltis unbuckled and the vehicle speedexceeds approximately 25 km/h (15.5mph).
Alarm warningThe alarm warning chime will sound if thevehicle is unlocked with the mechanicalkey and not the remote key. The chime willsound for up to 12 seconds until the unlockbutton is pressed on the remote key or acorrectly coded key is inserted into theignition and turned to position II or III. If 12second elapses before this occurs, thevehicle alarm will sound.
Key in ignition warningThe key in ignition warning chime willsound if the key is inserted into the ignition(but not turned to position II or III) and thedriver's door is opened.
Over speed warningOver speed warning chime will sound if thevehicle speed exceeds approximately 120km/h (74.5 mph) indicated.
60
Instrument Cluster
Low washer fluid warningLow washer fluid warning chime will soundif the washer fluid level in the washerbottle is low.
Missed lock warningMissed lock warning chime will sound ifthe door is not locked after pressing thelock button.Note: This feature is default off. To activateit, contact your Ford dealer.
61
Instrument Cluster
GENERAL INFORMATION
WARNINGDo not operate the informationdisplay controls when the vehicle ismoving.
Note: The information display will remainon for several minutes after you switch offthe ignition.
A B
C
E136109
Gear display (auto transmissiononly)
A
Trip computer displayBOdometer displayC
OdometerRegisters the total mileage of the vehicle.
TRIP COMPUTERControls
E136103
For item location: See Gauges (page 56).Press the SET/RESET button less than 2seconds to:• Select between the trip computer
displaysPress and hold the SET/RESET buttonfor more than two seconds to:• Reset trip A• Reset trip B• Reset average fuel consumption• Reset average speed
The trip computer display includes thefollowing information displays:
62
Information Displays
E136110
Tripmeter (A and B)
E138112
E138113
Registers the mileage of individualjourneys.
Distance to empty
E138114
Indicates the approximate distance thevehicle will travel on the fuel remaining inthe tank. Changes in driving pattern maycause the value to vary.
Average fuel consumption
E138117
63
Information Displays
E138118
Indicates the average fuel consumptionsince the function was last reset.
Instantaneous fuel consumption
E138115
E138116
Indicates the current average fuelconsumption.
Average speed
E138119
Indicates the average speed calculatedsince the function was last reset.
Outside air temperature
E138120
Shows the outside air temperature.
Note: The position of the trip computerdisplay may vary depending on theinformation shown in the display.
64
Information Displays
PERSONALISED SETTINGSLanguage setting
A
B
E138129
Language set menu activeALanguage title displayB
A choice of eleven languages are availablefrom 01 to 11 in the order shown below:01: English - GB02: Swedish - S03: German - D04: Dutch - NL05: French - F06: Italian - I07: Spanish - E08: Portuguese - P09: Turkish - TR10: Russian - RUS11: Polish - PLTo enter the language set menu:1. With ignition off, press and hold the
light dimming button. For item location:See Gauges (page 56). and switchignition to on.
2. The display will show the language setmenu active.
3. Press the SET/RESET to selectbetween the different languages.
4. Press and hold the SET/RESETbutton to set the currently displayedlanguage.
5. A chime will be heard to confirm theselection.
6. The display will then return to normaloperation.
Units of measureTo select metric or imperial units foroutside temperature display:1. Change display mode to "Outside
Temperature."2. Press and hold the SET/RESET
button for more than two seconds andthe units will change.
Toggling the units of measure using thisdisplay will affect the following displays:• Outside air temperature.• The temperature display in the
automatic climate control.• The set temperature in the
multi-function display.
65
Information Displays
PRINCIPLE OF OPERATIONOutside airKeep the air intakes forward of thewindscreen free from obstruction (snow,leaves etc.) to allow the climate controlsystem to function effectively.
Recirculated airCAUTION
Prolonged use of recirculated air maycause the windows to mist up. If thewindows mist up, follow the settings
for defrosting and demisting thewindscreen.
The air currently in the passengercompartment will be recirculated. Outsideair will not enter the vehicle.
HeatingHeating performance depends on thetemperature of the engine coolant.
Air conditioningNote: The air conditioning operates onlywhen the temperature is above 4°C (39°F).Note: If you use the air conditioning, thefuel consumption of your vehicle will behigher.Air is directed through the evaporatorwhere it is cooled. Humidity is extractedfrom the air to help keep the windows freeof mist. The resulting condensation isdirected to the outside of the vehicle andit is therefore normal if you see a smallpool of water under your vehicle.
General information on controllingthe interior climateFully close all the windows.
Warming the interiorDirect the air towards your feet. In cold orhumid weather conditions, direct some ofthe air towards the windscreen and thedoor windows.
Cooling the interiorDirect the air towards your face.
AIR VENTS
E132643
MANUAL CLIMATE CONTROLAir distribution control
AB C D
E
E132661
Face levelAFace level and footwellB
66
Climate Control
FootwellCFootwell and windscreenDWindscreenE
You can set the air distribution control toany of the indicated positions. A smallamount of air is directed towards thewindscreen in positions B and C.
Blower
01 2 3
4
A
E132663
OffA
Temperature control
E132662
ColdBlueWarmRedMaximun coolingA/C
MAX
Recirculated air
Press the recirculated air button to togglebetween outside air and recirculated air.
System settingsNote: Set all controls to the positionsshown.
Heating the interior quickly
01 2 3
4
E132666
Select the outside air.
67
Climate Control
Ventilation
BA
01 2 3
4
E132667
Face level and footwellAFace levelB
Set the air distribution control to positionA or position B. Set the blower andtemperature to any position and select theoutside air. Open the air vents to suitindividual requirements.
Switching the air conditioning on andoff
E91393
Press the A/C button to switch the airconditioning on and off.
Cooling with outside air
01 2 3
4
E132668
Switch the air conditioning on and selectthe outside air.
Cooling the interior quickly
01 2 3
4
E132669
Selecting the A/C MAX will providemaximum occupant cooling. To switch theA/C MAX off deselect the A/C orrecirculated air.
Defrosting and demisting thewindscreen quickly
01 2 3
4
E132665
Selecting air to windscreen willautomatically switch the A/C on and selectthe outside air.
Reducing interior air humidity
01 2 3
4
E132670
68
Climate Control
Selecting air to windscreen willautomatically switch the A/C on and selectthe outside air.
AUTOMATIC CLIMATECONTROLThe system controls the temperature,amount and distribution of the air flowautomatically and adjusts them accordingto the driving and weather conditions. Ashort press of the AUTO button onceswitches on the auto mode.Note: When in AUTO, ensure that thetemperature is set to the desired level.Note: If the climate control is operated,information relating to this system isdisplayed in the information display. SeeInformation Displays (page 62).Note: Avoid adjusting the settings whenthe vehicle interior is extremely hot or cold.The automatic climate control adjusts tothe current circumstances automatically.For the system to function properly, the sideand centre vents should be fully open.Note: The sunload sensor is located on topof the instrument panel. Do not cover thesensor with any objects.Note: The in car temperature sensor islocated behind the grill below the airdistribution control. Do not cover the grillwith any objects.Note: At low outside temperatures, whenthe system is in auto mode, the air flow willbe low and the air stream will be directedto the windscreen and the side windows aslong as the engine is cold.
Air distribution control
A
B
C
E132685
WindscreenAFace levelBFootwellC
To adjust air distribution, press the desiredbutton. The combination of settings thatcan be selected are A, B, C, A and C andB and C.
Blower
E132686
69
Climate Control
Note: When the blower is in AUTO mode,no blower setting indicators will beilluminated.When the blower speed is controlledmanually by operationg the blower dial,the blower setting is indicated in thedisplay above the air distribution controls.To return to auto mode, short press theAUTO button.
Temperature control
E132687
You can set the temperature between 16°C(61°F) and 28°C (82°F) in steps of 0.5°C(1°F). In position LO (below 16°C (61°F))the system will switch to permanentcooling, in HI (above 28°C (82°F)) topermanent heating, and not regulate astable temperature.
Mono ModeIn Mono mode the temperature settingsfor both the driver’s and passenger’s sideare linked. If you adjust the temperatureusing the rotary control on the driver’s side,the settings will be adjusted to the samesetting on the passenger’s side.
To switch dual mode onNote: Adjusting the blower speed will putthe system into DUAL mode.Select a temperature for the passenger’sside with the rotary control on thepassenger’s side. The temperature for thedriver’s side will remain unchanged. Youcan now adjust the driver and passengerside temperatures independently. Thetemperature settings for each side areshown in the display. You can set atemperature difference of up to 4°C (8°F).Note: If you set a temperature differenceof greater than 4°C (8°F), the temperatureon the other side will be adjusted so thatthe difference remains 4°C (8°F).
To switch dual mode offPress the AUTO button for three secondsor select HI or LO on the driver's side. Thepassenger’s side temperature will beadjusted to the driver’s side temperature.
Recirculated air
Press the recirculated air button to togglebetween fresh air and recirculated air.Note: When the system is in auto mode andthe interior and exterior temperatures arequite hot, the system selects recirculatedair automatically to maximise cooling of theinterior. Once the selected temperature isreached, the system will reselect outside airautomatically.
Cooling the interior quickly
E132664
70
Climate Control
Selecting the A/C MAX will providemaximum occupant cooling. A secondpress of the A/C MAX button will switchthe A/C MAX off.
Windscreen defrosting anddemisting
E132688
Press the MAX defrost button for quickdemisting of the windscreen.Fresh air will flow into the vehicle and A/Cis automatically selected. The blowerspeed, temperature control and fresh airoperate automatically and cannot beadjusted in this mode. The blower is set tomaximum speed and the temperature toHI.When you select MAX defrost, the heatedwindows switch on automatically andswitch off after a preset time.A second press of the MAX defrost buttonwill return the system to the previoussettings.To return to auto mode, short press theAUTO button.
Switching the air conditioning onand off
E91393
Press the A/C button to switch the airconditioning on and off. The light in thebutton indicates the status of the A/C.Note: The A/C operates only when theengine is running.
Switching off the automaticclimate control
E132690
Press the power button to switch thesystem on and off. When switched off,recirculated air is selected but it is alsopossible to manually select the fresh air.
HEATED WINDOWS ANDMIRRORSHeated windowsUse the heated windows to defrost ordemist the windscreen or rear window.Note: The heated windows operate onlywhen the engine is running.Note: The heated windows willautomatically switch off after a preset time.
Heated windscreen
E103392
Press the heated windscreen button toswitch the heated windscreen on and off.
Heated rear window
E72507
Press the heated rear window button toswitch the heated rear window on and off.
Heated exterior mirrorsHeated exterior mirrors are fitted with aheating element that will defrost or demistthe mirror glass. They will switch onautomatically when you switch the heatedwindscreen on.
71
Climate Control
SITTING IN THE CORRECTPOSITION
E68595
WARNINGSDo not adjust the seats when thevehicle is moving.Only when you use the seat beltproperly, can it hold you in a positionthat allows the airbag to achieve its
optimum effect.
When you use them properly, the seat,head restraint, seat belt and airbags willprovide optimum protection in the eventof a collision. We recommend that you:• sit in an upright position with the base
of your spine as far back as possible.• do not recline the seatback more than
30 degrees.• adjust the head restraint so that the
top of it is level with the top of yourhead and as far forwards as possible,remaining comfortable.
• keep sufficient distance betweenyourself and the steering wheel. Werecommend a minimum of 250millimetres (10 inches) between yourbreastbone and the airbag cover.
• hold the steering wheel with your armsslightly bent.
• bend your legs slightly so that you canpress the pedals fully.
• position the shoulder strap of the seatbelt over the centre of your shoulderand position the lap strap tightly acrossyour hips.
Make sure that your driving position iscomfortable and that you can maintain fullcontrol of your vehicle.
FRONT SEATS
WARNINGSDo not use any accessory seat coversthat are not specifically designed forseats with side airbags. These seat
covers must be fitted by properly trainedtechnicians.
Do not adjust the seats when thevehicle is moving.
Adjusting the lumbar support
E131595
72
Seats
Moving the seats backwards andforwards (Manual seats)
E131590
WARNINGRock the seat backwards andforwards after releasing the lever tomake sure that it is fully engaged in
its catch.
CAUTIONDo not move the front seats too closeto the instrument panel.
Adjusting the height of the driver’sseat (Manual seats)
E131593
Each pull or press on the lever will raise orlower the height by a small amount.
Adjusting the angle of theseatback (Manual seats)
E131592
73
Seats
WARNINGSRock the seatback backwards andforwards after releasing the lever tomake sure that it is fully engaged in
its catch.If the front passenger seat has beenmoved forwards, rock the seatbackwards and forwards after
releasing the lever to make sure that it isfully engaged in its catch.
Front seat - Stretch cab
E136219
Note: On stretch cab vehicles the frontpassenger seat can be adjusted to allow therear passenger to gain easier access.
Folding the seat backrest (Benchseat - Single cab)
E135862
Moving the seats backwards andforwards (Electric seats)
E131591
74
Seats
CAUTIONDo not move the front seats too closeto the instrument panel.
Adjusting the height of the driver’sseat (Electric seats)
E131594
Adjusting the angle of theseatback (Electric seats)
E131596
Tilting the seat (Electric seats)
E131607
75
Seats
HEAD RESTRAINTSAdjusting the head restraint
WARNINGSRaise the rear head restraint whenthe rear seat is occupied by apassenger.When using a forward facing childrestraint on a rear seat, alwaysremove the head restraint from that
seat.
E135814
Adjust the head restraint so that the topof it is level with the top of your head.
Removing the head restraintPress the locking button using a suitabletool and remove the head restraint.
E135815
REAR SEATSFolding the rear seat cushionStretch cab
2
2
1
E131743
Double cab
1
2
3
E133361
76
Seats
CAUTIONWhen the cushion is folded down, thecushion tether strap must be stowedin the pocket provided.
Folding the rear seatback - Doublecab
WARNINGWhen folding the seatbacks down,take care not to get your fingerscaught between the seatback and
seat frame.
CAUTIONSDo not use the rear surface of the rearseat back as a load floor.Do not de-latch and fold the seatback when the seat cushion is foldedup.
1
2
E131744
To fold the seatback down1. Pull the release strap upwards.2. Push the seatback forwards.
To return the seatback to its uprightposition:1. Push the seatback to the upright
position.WARNINGS
When folding the seatbacks up,make sure that the belts are visibleto an occupant and not caught
behind the seat.Make sure that the rear seatback issecure and fully engaged in itscatches
Rear seat arm rest
E131745
HEATED SEATS
CAUTIONOperating this function with theengine off will drain the battery.
77
Seats
E131536
The seat heating will operate only whenthe ignition is switched on.The maximum temperature is reachedafter five or six minutes. It is regulatedthermostatically.The seat heating will remain on until eitherthe heated seat switch or the ignition isturned off.
78
Seats
CLOCKFor detailed instructions on how to adjustthe clock. See Setting the clock on theaudio unit (page 193).
INSTRUMENT LIGHTINGDIMMERNote: Adjusting the illumination dimmerswitch will alter the illlumination level of theinterior displays and switches.
E133586
For item location: See Gauges (page 56).Press the dimming button to step theillumination dimming level in large steps.Press and hold the dimming button toadjust the illumination dimming levelsmoothly in fine adjustment levels.
CIGAR LIGHTER
CAUTIONSIf you use the socket when the engineis not running, the battery maydischarge.Do not hold the cigar lighter elementpressed in.
Note: You can use the socket to power 12volt appliances that have a maximumcurrent rating of 10 Amperes. Use only Fordaccessory connectors or connectorsspecified for use with SAE standard sockets.
E136788
Press the element in to use the cigarlighter. It will pop out automatically.For item location: See At a Glance (page9).
ASHTRAYNote: The removable ashtray can be placedin any of the front or rear cup holders.
E136222
79
Convenience features
AUXILIARY POWER POINTS
E133428
CAUTIONIf you use the auxiliary power socketwhen the engine is not running, thebattery may discharge.
Note: Switch the ignition on to use theauxiliary power socket.You can use the auxiliary power socket topower 12 volt appliances that have amaximum current rating of 10 Amperes.Use only Ford accessory connectors orconnectors specified for use with SAEstandard sockets. For item location: SeeAt a Glance (page 9).
CUP HOLDERS
WARNINGSDo not place hot drinks in the cupholders when the vehicle is moving.Do not place glass objects in the cupholders.
Front cup holdersType 1
E132722
Type 2
E132723
80
Convenience features
Rear cup holdersType 2
E132724
GLASSES HOLDER
E133675
STORAGE COMPARTMENTSDriver side
E133607
Passenger side
E136461
81
Convenience features
Centre console
E136462
E136463
AUXILIARY INPUT (AUX IN)SOCKET
E133606
For item location see: See At a Glance(page 9).
See Auxiliary input (AUX IN) socket(page 205).
USB PORT
E133603
For item location: See At a Glance (page9).See Connectivity (page 229).
COOL BOX
A
B
E132725
OpenACloseB
The cold air flow inside the cool box canbe adjusted using the control lever.
82
Convenience features
FLOOR MATS
WARNINGSWhen using the floor mats, alwaysmake sure the floor mat is properlysecured using the appropriate fixings
and positioned so that it does not interferewith the operation of the pedals.
Do not install additional floor matson top of the factory installed floormats.
E136481
83
Convenience features
GENERAL INFORMATIONGeneral points on startingIf the battery has been disconnected thevehicle may exhibit some unusual drivingcharacteristics for approx. 8 kilometres (5miles) after reconnecting the battery.This is because the engine managementsystem must realign itself with the engine.Any unusual driving characteristics duringthis period may be disregarded.
Starting the engine by towing orpushing
WARNINGTo prevent damage you must notpush or tow start your vehicle. Usebooster cables and a booster battery.
See Jump-Starting the Vehicle (page152).
IGNITION SWITCH
WARNINGNever return the key to position 0 orI when the vehicle is in motion.
E72128
0 The ignition is off.I The ignition and all main electrical circuitsare disabled.Note: Do not leave the ignition key in thisposition for too long to avoid dischargingthe battery.
II The ignition is switched on. All electricalcircuits are operational. Warning lampsand indicators illuminate. This is the keyposition when driving. You must also selectit when being towed.III The starter motor is activated. Releasethe key as soon as the engine starts.
STEERING WHEEL LOCKWhen you remove the key from the ignitionswitch, the steering column lock isactivated as soon as you turn the steeringwheel.The steering will be unlocked when the keyis moved to position ACC.
STARTING A PETROL ENGINENote: You can only operate the starter fora maximum of 30 seconds at a time.
Cold or hot engineAll vehicles
CAUTIONWhen the temperature is below -20°C(-4°F), switch the ignition on for atleast one second before starting the
engine. This will make sure that themaximum fuel pressure is established forstarting the engine.
Vehicles with manual transmissionNote: Do not touch the accelerator pedal.1. Fully depress the clutch pedal.2. Start the engine.
Vehicles with automatic transmissionNote: Do not touch the accelerator pedal.1. Select park or neutral.2. Fully depress the brake pedal.
84
Starting and Stopping the Engine
3. Start the engine.
All vehiclesIf the engine does not start within 15seconds, wait for a short period and tryagain.If the engine does not start after threeattempts, wait 10 seconds and follow theFlooded engine procedure.If you have difficulty starting the enginewhen the temperature is below -25°C(-13°F), press the accelerator pedalbetween ¼ to ½ of its travel and try again.
Flooded engineVehicles with manual transmission1. Fully depress the clutch pedal.2. Fully depress the accelerator pedal and
hold it there.3. Start the engine.
Vehicles with automatic transmission1. Select park or neutral.2. Fully depress the accelerator pedal and
hold it there.3. Fully depress the brake pedal.4. Start the engine.
All vehiclesIf the engine does not start, repeat theCold or hot engine procedure.
Engine idle speed after startingThe speed at which the engine idlesimmediately after starting will varydepending on the engine temperature.If the engine is cold then the idle speed willautomatically be increased in order to heatthe catalytic converter as quickly aspossible. This makes sure that vehicleemissions are kept to an absoluteminimum.
The idle speed will slowly decrease to thenormal level as the catalytic converterwarms up.
STARTING A DIESEL ENGINECold or hot engineAll vehiclesNote: When the temperature is below -15°C(5°F), you may need to crank the engine forup to 25 seconds.Note: Continue cranking the engine until itstarts.Note: You can only operate the starter fora maximum of 30 seconds at a time.
Switch the ignition on and waituntil the glow plug indicator goesoff.
Vehicles with manual transmissionNote: Do not touch the accelerator pedal.1. Fully depress the clutch pedal.2. Start the engine.
Vehicles with automatic transmission1. Select park or neutral.2. Fully depress the brake pedal.3. Start the engine.
DIESEL PARTICULATE FILTERThe DPF forms part of the emissionsreduction systems fitted to your vehicle. Itfilters harmful diesel particulates (soot)from the exhaust gas.
85
Starting and Stopping the Engine
RegenerationWARNING
Do not park or idle your vehicle overdry leaves, dry grass or othercombustible materials. The DPF
regeneration process creates very highexhaust gas temperatures and the exhaustwill radiate a considerable amount of heatduring and after DPF regeneration, andafter you have switched the engine off.This is a potential fire hazard.
CAUTIONAvoid running out of fuel.
Unlike a normal filter which requiresperiodic replacement, the DPF has beendesigned to regenerate, or clean itself tomaintain operating efficiency. Theregeneration process takes placeautomatically. However, some drivingconditions mean that you may need tosupport the regeneration process.If you drive only short distances or yourjourneys contain frequent stopping andstarting, where there is increasedacceleration and deceleration, occasionaltrips with the following conditions willassist the regeneration process:• Drive your vehicle at a constant speed,
preferably on a main road or motorway,for up to 20 minutes.
• Avoid prolonged idling and alwaysobserve speed limits and roadconditions.
• Do not switch off the ignition.• Use a lower gear than normal to
maintain a higher engine speed duringthis journey, where appropriate.
SWITCHING OFF THE ENGINEVehicles with a turbocharger
CAUTIONDo not switch the engine off when itis running at high speed orimmediately after heavy towing. If you
do, the turbocharger will continue runningafter the engine oil pressure has droppedto zero. This will lead to prematureturbocharger bearing wear.
Release the accelerator pedal. Wait untilthe engine has reached idle speed and thenswitch it off.
86
Starting and Stopping the Engine
SAFETY PRECAUTIONS
WARNINGSStop refuelling after the fuel nozzlestops the second time. Additionalfuel will fill the expansion space in
the fuel tank which could lead to fueloverflowing. Fuel spillage could behazardous to other road users.
Do not use any kind of flames or heatnear the fuel system. The fuel systemis under pressure. There is a risk of
injury if the fuel system is leaking.
FUEL QUALITY - PETROL
CAUTIONDo not use leaded petrol or petrol withadditives containing other metalliccompounds (e.g. manganese-based).
They could damage the emission system.
Note: We recommend that you use onlyhigh quality fuel.Note: The use of additives or other enginetreatments not approved by Ford is notrecommended.Note: Ethanol blended fuels up to 10%(E10) is acceptable to be used in thisvehicle.Use minimum 91 octane unleaded petrolthat meets the relevant nationalspecification.
FUEL QUALITY - DIESEL
WARNINGDo not mix diesel with oil, petrol orother liquids. This could cause achemical reaction.
CAUTIONSDo not add kerosene, paraffin orpetrol to diesel. This could causedamage to the fuel system.Use diesel that meets the relevantnational specification.
Note: We recommend that you use onlyhigh quality fuel.Note: The use of additives or other enginetreatments not approved by Ford is notrecommended.Note: Bio-diesel blended fuels up to 10%(B10) is acceptable to be used in thisvehicle.
Long-term storageMost diesel fuels contain bio-diesel, it isrecommended to fill the tank with purelymineral diesel (where available) or add ananti-oxidant prior to long-term storage ofyour vehicle exceeding two months. Yourdealer can help you with a suitableanti-oxidant.
CATALYTIC CONVERTER
WARNINGDo not park or idle your vehicle overdry leaves, dry grass or othercombustible materials. The exhaust
will radiate a considerable amount of heatduring use, and after you have switchedthe engine off. This is a potential firehazard.
Driving with a catalytic converterCAUTIONS
Avoid running out of fuel.
Do not crank the engine for longperiods.
87
Fuel and Refuelling
CAUTIONSDo not push-start or tow-start yourvehicle. Use booster cables. SeeJump-Starting the Vehicle (page
152).Do not switch the ignition off whendriving.
FUEL FILLER FLAP
WARNINGSTake care when refuelling to avoidspilling any residual fuel from the fuelnozzle.Do not use any kind of flames or heatnear the fuel system. The fuel systemis under pressure. There is a risk of
injury if the fuel system is leaking.
CAUTIONIf you use a high pressure spray towash your vehicle, only spray the fuelfiller flap briefly from a distance not
less than 20 centimetres (8 inches).
Note: Central locking also locks andunlocks the fuel filler flap. See Locking andUnlocking (page 29).
Vehicles equipped with capsystem
E136220
E131286
1. Press the flap to open it.2. Open the flap fully until it engages.
Turn the fuel filler cap anti-clockwise.3. When the filler cap is removed , a
hissing noise may be heard. This isnormal and should be disregarded.
4. To close, turn the fuel filler capclockwise until it clicks.
5. Close and push the fuel filler flap tolock it.
88
Fuel and Refuelling
Vehicle equipped with caplesssystem
E136220
E135241
1. Press the flap to open it.2. Close and push the fuel filler flap to
lock it.When you insert the fuel nozzle, a springloaded inhibitor will open if the correct sizenozzle is detected. This helps to avoidfilling up with the wrong fuel.Note: A funnel is located in the glove box.Use this when refilling with a fuel can.
FillingWARNING
Stop refuelling after the fuel nozzlestops the second time. Additionalfuel will fill the expansion space in
the fuel tank which could lead to fueloverflowing. Fuel spillage could behazardous to other road users.
E135239
Fully insert the fuel nozzle. Lower thenozzle so that it locks in place on the fuelpipe opening. Keep it resting at thisposition and initiate refuelling by pullingthe trigger.
WARNINGWe recommend that you wait atleast 10 seconds before removing thefuel nozzle to allow any residual fuel
to drain into the fuel tank.
89
Fuel and Refuelling
E135240
Slightly raise the fuel nozzle to remove it.
REFUELLING
CAUTIONDo not attempt to start the engine ifyou have filled the fuel tank with theincorrect fuel. This could damage the
engine. Have the system checked by aproperly trained technician immediately.
FUEL CONSUMPTIONThe CO2 and fuel consumption figures arederived from laboratory tests according toEEC Directive 80/1268/EEC andsubsequent amendments and are carriedout by all vehicle manufacturers.They are intended as a comparisonbetween makes and models of vehicles.They are not intended to represent the realworld fuel consumption you may get fromyour vehicle. Real world fuel consumptionis governed by many factors including;driving style, high speed driving, stop/startdriving, air conditioning usage, theaccessories fitted and towing etc.Your Ford dealer can give you advice onimproving your fuel consumption.
TECHNICAL SPECIFICATIONSFuel Consumption Figures
CO2 Emis-sionsCombinedExtra-UrbanUrban
Variantg/kml/100 km
(mpg)l/100 km
(mpg)l/100 km
(mpg)
24410.2 (27.7)8.2 (34.4)13.6 (20.7)Vehicles with a 2.5LDuratec-HE engine - 2-wheel drive
25910.8 (26.1)8.9 (31.7)14.1 (20.0)Vehicles with a 2.5LDuratec-HE engine - 4-wheel drive
2037.6 (37.2)6.8 (41.5)9.0 (31.4)Vehicles with a 2.2LDuratorq-TDCi engine - 2-wheel drive (manual trans-mission - MT82)
90
Fuel and Refuelling
CO2 Emis-sionsCombinedExtra-UrbanUrban
Variantg/kml/100 km
(mpg)l/100 km
(mpg)l/100 km
(mpg)
2178.1 (34.9)7.1 (39.8)9.9 (28.5)Vehicles with a 2.2LDuratorq-TDCi engine - 4-wheel drive (manual trans-mission - MT82)
2388.9 (31.7)7.6 (37.2)11.1 (25.4)Vehicles with a 2.2LDuratorq-TDCi engine - 2-wheel drive (automatictransmission)
2519.4 (30.0)7.9 (35.7)12.1 (23.3)Vehicles with a 2.2LDuratorq-TDCi engine - 4-wheel drive (automatictransmission)
2228.4 (33.6)7.0 (40.3)10.8 (26.1)Vehicles with a 3.2LDuratorq-TDCi engine - 2-wheel drive (manual trans-mission - MT82)
2419.1 (31.0)7.6 (37.1)11.8 (23.9)Vehicles with a 3.2LDuratorq-TDCi engine - 4-wheel drive (manual trans-mission - MT82)
2398.9 (31.7)7.4 (38.2)11.6 (24.3)Vehicles with a 3.2LDuratorq-TDCi engine - 2-wheel drive (automatictransmission)
2519.4 (30.0)7.9 (35.7)12 (23.5)Vehicles with a 3.2LDuratorq-TDCi engine - 4-wheel drive (automatictransmission)
91
Fuel and Refuelling
MANUAL TRANSMISSIONSelecting reverse gear
CAUTIONDo not engage reverse gear when thevehicle is moving. This can causedamage to the transmission.
Note: Fully depress the clutch pedal andwait for three seconds before you selectreverse gear.
E131287
On some vehicles it is necessary to raisethe collar whilst selecting reverse gear.
FOUR-WHEEL DRIVENote: A clicking sound from the drivelinemay be heard while shifting between ranges,which is normal.
E132692
Two-wheel drive, high range (2H)Use for all normal road driving and also foroff-road driving across dry, level terrain.
Four-wheel drive, high range (4H)WARNING
Do not use four-wheel drive 4H fornormal road driving.
Note: The four-wheel drive indicator lampwill come on when the transfer shift switchis in the 4H position. See Warning Lampsand Indicators (page 56).Use for off-road driving.
Four-wheel drive, low range (4L)WARNING
Do not use four-wheel drive 4L fornormal road driving.
Note: The four-wheel drive low range 4Land four-wheel drive indicator lamps willcome on when the transfer shift switch is inthe 4L position. See Warning Lamps andIndicators (page 56).
92
Transmission
Use for more extreme off-road conditions,such as steep ascents and descents.Also use when low speed manoeuvring isnecessary, such as reversing a trailer ornegotiating a boulder-strewn river bed.
Shifting between 2H and 4HNote: When shifting to 2H, all the stabilitycontrol (ESP) functions are reactivated.This can be done with the vehicle movingup to 120km/h (74 mph), but only with theaccelerator pedal released. During the shiftthe indicator lamp will flash. If it does notflash, reverse the vehicle for a shortdistance with the steering wheel turned.
Shifting between 2H and 4LNote: When shifting to 4L the EngineTraction Control and Trailer Stability Controlare deactivated. Hill Descent Control, HillStart Assist and Brake Traction Controlremain active.Note: When shifting to 2H, all the stabilitycontrol (ESP) functions are reactivated.1. Stop the vehicle when it is safe to do
so.2. Depress the clutch pedal (manual
transmission).3. Move the transmission selector lever
to the neutral (N) position (automatictransmission).
4. Turn the transfer shift switch from 2Hto 4L or 4L to 2H.
During the shift the indicator lamp willflash. If it does not flash, reverse the vehiclefor a short distance with the steering wheelturned.
Shifting between 4H and 4LNote: When shifting to 4L the EngineTraction Control and Trailer Stability Controlare deactivated. Hill Descent Control, HillStart Assist and Brake Traction Controlremain active.1. Stop the vehicle when it is safe to do
so.2. Depress the clutch pedal (manual
transmission).3. Move the transmission selector lever
to the neutral (N) position (automatictransmission).
4. Turn the transfer shift switch from 4Hto 4L or from 4L to 4H.
During the shift the indicator lamp willflash.
ELECTRONIC LOCKINGDIFFERENTIAL
WARNINGThe vehicle should not be operatedon sealed roads with the systemengaged. Doing so may lead to
excessive tyre noise and wear. The systemis intended for use on consistently slipperyor loose surfaces.
The system locks the left and right portionsof the rear axle together to form a soliddriving axle, resulting in increased rearwheel traction in certain conditions.Note: The system will only activate if thevehicle speed is less than 30 km/h (20mph) and the accelerator pedal is released.Press the Electronic Locking Differential(ELD) button to activate the system. Foritem location: See At a Glance (page 9).
93
Transmission
The rear axle will lock and unlock onlywhen the internal gears are aligned andthere is no torque load on the differential.To aid alignment, drive the vehicle in astraight line with the accelerator pedalreleased. Alternatively, drive slowlyforwards and backwards while moving thesteering wheel from side to side to allowthe internal differential gears to align.Note: The system can be used in anytransmission drive range (2H, 4H or 4L).The system will:• Automatically disengage when a speed
of 40 km/h (25 mph) is exceeded.• Automatically re-engage when the
speed drops below 30 km/h (20 mph).• Automatically disengage when the
ignition is turned off.If the system is selected when drivingabove 40 km/h (25 mph), the request isstored and will be engaged when thevehicle speed reduces to 30 km/h (20mph). The ELD indicator lamp will flashuntil either the vehicle speed reduces andthe differential lock is engaged or the driverdeselects the ELD button.Note: When the system is engaged, theElectronic Stability Program (ESP) functionssuch as Stability Control, Traction Control,Hill Descent Control, Hill Start Assist andTrailer Stability Control will be deactivated.Note: When the ABS is operating, thesystem will be disengaged.
AUTOMATIC TRANSMISSIONSelector lever positions
PRNDS -+
1
2
E132720
ParkPReverseRNeutralNDriveDSport mode and manual shiftingSManual shift upS+Manual shift downS-
WARNINGApply the brakes before moving theselector lever and keep them applieduntil you are ready to move off.
Note: A cold engine has a higher idle speed.This will increase the tendency for yourvehicle to creep when you have selected adrive gear.Press the button on the selector lever toselect reverse and park.
94
Transmission
The selector lever position will be shownin the information display.
Park
WARNINGSSelect park only when your vehicleis stationary.Apply the parking brake and selectpark before leaving your vehicle.Make sure that the selector lever is
latched in position.
Note: To move the selector lever from parkposition, apply the footbrake and ignitionkey in position II.Note: An audible warning will sound if youopen the drivers door and you have notselected park.Note: The battery saver will deactivate thewarning chime after a period of time.In this position, power is not transmittedto the drive wheels and the transmissionis locked. You can start the engine with theselector lever in this position.
Reverse
WARNINGSelect reverse only when your vehicleis stationary and the engine is at idlespeed.
NeutralIn this position, power is not transmittedto the drive wheels but the transmission isnot locked. You can start the engine withthe selector lever in this position.
DriveSelect drive to shift automatically throughthe forward gears.
Sport modeNote: Sport mode is to shift automaticallythrough the forward gears in a more sportymanner.Note: When towing heavy loads, or in hillyterrain, it is recommended that sport modeis selected. This will result in coolertransmission temperatures and additionalengine braking.Activate sport mode by moving theselector lever from drive position towardsthe driver. This is indicated in theinstrument cluster by displaying 'S'. SeeGeneral Information (page 62).Sport mode will remain active until youshift manually up or down the gears.Note: When you select position S, a gearchange may occur depending on theaccelerator pedal position in relation toactual vehicle speed.
Manual shifting
PRND S-+
E136209
Note: A shift will occur only when thevehicle speed and the engine speed areappropriate.
95
Transmission
Manual shifting can be done only when theselector lever is in position S. Move theselector lever forward to downshift andbackward to upshift.
WARNINGDo not hold the selector leverpermanently in – or +.
When the vehicle is stationary, only the 1stand 2nd gears can be selected.Manual shifting is sequential, thereforegears cannot be skipped.The transmission will remain in theselected gear. When the engine speed istoo low or idle, it will downshift to 2nd gear.The selected gear is indicated in theinstrument cluster. See GeneralInformation (page 62).
Drive modesThe transmission will select theappropriate gear for optimum performancebased on ambient temperature, roadgradient, vehicle load and driver input.
Hints on driving with an automatictransmissionMoving off
WARNINGIt is not possible to tow-start orpush-start a vehicle fitted with anautomatic transmission. See
Jump-Starting the Vehicle (page 152).
1. Release the parking brake.2. Release the brake pedal and press the
accelerator pedal.
Stopping1. Release the accelerator pedal and
press the brake pedal.
2. Apply the parking brake.
KickdownPress the accelerator pedal fully with theselector lever in the drive position to selectthe next highest gear for optimumperformance. Release the acceleratorpedal when you no longer requirekickdown.
Emergency park position releasebutton
E132721
Use the button to move the selector leverfrom the park position in the event of anelectrical malfunction or if your vehicle hasa flat battery.
CAUTIONTake care when opening the cover.
Lift up the cover in the centre console nextto the selector lever with a suitable tool.Push down the locking button in the slotand simultaneously move the selectorlever out of the P position.Note: If position P is selected again, thisprocedure must be repeated.
96
Transmission
PRINCIPLE OF OPERATIONDisc brakesWet brake discs result in reduced brakingefficiency. Dab the brake pedal whendriving from a car wash to remove the filmof water.
ABSWARNING
The ABS does not relieve you of yourresponsibility to drive with due careand attention.
The ABS helps you to maintain full steeringand directional stability when you brakeheavily in an emergency, by preventing theroad wheels from locking.
Brake overrideIn the event that the accelerator pedalbecomes stuck or entrapped, applyingsteady and firm pressure to the brakepedal will both slow the vehicle and reduceengine power.If you experience this condition:1. Apply the brakes and bring your vehicle
to a safe stop.2. Turn the engine off.3. Select park (automatic transmission
only).4. Apply the parking brake.Inspect the accelerator pedal for anyinterferences. If none are found and thecondition persists, have your vehicle towedto a dealer.
HINTS ON DRIVING WITHANTI-LOCK BRAKESNote: When the system is operating, thebrake pedal will pulse and may travelfurther. Maintain pressure on the brakepedal. You may also hear a noise from thesystem. This is normal.The ABS will not eliminate the risks when:• you drive too close to the vehicle in
front of you• the vehicle is aquaplaning• you take corners too fast• the road surface is poor.
PARKING BRAKE
WARNINGVehicles with an automatictransmission should always be leftwith the selector lever in position P
(Park).
• Press the foot brake pedal firmly.• Pull the parking brake lever up smartly
to its fullest extent.• Do not press the release button while
pulling the lever up.• If your vehicle is parked on a hill and
facing uphill, select first gear or P(Park) and turn the steering wheelaway from the kerb.
• If your vehicle is parked on a hill andfacing downhill, select reverse gear orP (Park) and turn the steering wheeltowards the kerb.
To release the parking brake, press thebrake pedal firmly, pull the lever up slightly,depress the release button and push thelever down.
97
Brakes
PRINCIPLE OF OPERATIONHDC operates in conjunction with ABS toprovide greater control when off-road,particularly when descending steep slopes.HDC operation is fully automatic whenengaged.During a hill descent when driving off-road,engine braking is used to control the speedof descent. If engine braking alone isinsufficient to control the vehicle's speed,HDC will slow the vehicle using the brakingsystem.If the vehicle is fitted with a manualtransmission, HDC should only be used infirst, or reverse gears. If the vehicle is fittedwith an automatic transmission, HDCshould only be used in D, R, or Sport mode1. When in D the vehicle will select themost appropriate gear.
Before driving off-roadWARNING
Before driving off-road it isabsolutely essential thatin-experienced drivers become fully
familiar with the vehicle's controls. Inparticular, Sport mode, Hill DescentControl (HDC).
USING HILL DESCENTCONTROLNote: When the rear differential lock isengaged, the HDC will not be available.
Selecting HDCHDC can be selected at speeds below 60km/h (35 mph). To select HDC, press andrelease the HDC on/off switch. For itemlocation: See At a Glance (page 9).
The HDC switch will illuminatecontinuously at speeds below40 km/h (25 mph) to indicate
that HDC is fully active.
If the vehicle speed exceeds 60 km/h (35mph) HDC will disengage, and the HDCswitch illumination will go off.
HDC operation
E102680
With HDC engaged, the speed of descentcan be altered using the cruise controlsteering wheel switches. SET + increasesthe speed, and SET - decreases the speed.To increase speed press, and hold, the SET+ switch until the desired speed isachieved. When the switch is released, thespeed will be maintained.To decrease speed press, and hold, theSET - switch until the desired speed isachieved. When the switch is released, thespeed will be maintained.To increase or decrease speed gradually,tap the SET + or SET - switch as required.Each tap of the switch will increase, ordecrease the speed in increments of 0.5km/h (0.3 mph). The speed can also beincreased or decreased by pressing theaccelerator pedal or brake pedalrespectively.Note: Each gear has a pre-determinedminimum speed.
98
Hill descent control (HDC)
Note: Descent speed will only increase ona slope steep enough to provide additionalmomentum. Therefore, use of the + switchon a gentle slope may not increase thespeed.Note: If the brake pedal is depressed, HDCwill be overridden and the brakes willoperate as normal. When the brake pedalis released, HDC will resume control of thedescent.Note: If HDC is switched off during adescent, HDC assistance will fade outgradually. This is to prevent loss of controlif HDC is switched off in error. HDC willresume control when switched back on ifassistance is still required, but at the speedthe vehicle is travelling when the pedal isreleased.When driving off-road HDC can bepermanently selected, but it will onlyprovide assistance when the speedparameters are met.
99
Hill descent control (HDC)
PRINCIPLE OF OPERATIONElectronic stability programme(ESP)
WARNINGESP does not relieve you of yourresponsibility to drive with due careand attention.
E72903
A A
AB
B
B
B
without ESPAwith ESPB
The ESP supports stability when thevehicle starts to slide away from yourintended path. This is performed by brakingindividual wheels and reducing enginetorque as needed.The system also provides an enhancedtraction control function by reducingengine torque and braking if the wheelsspin when you accelerate. This improvesyour ability to pull away on slippery roadsor loose surfaces, and improves comfortby limiting wheel spin in hairpin bends.
Stability control (ESP) warning lampThe ESP warning lamp will flash when thesystem is operating. See Warning Lampsand Indicators (page 56).
Emergency brake assistWARNING
Emergency brake assist does notrelieve you of your responsibility todrive with due care and attention.
Emergency brake assist will detect whenyou brake heavily by measuring the rate atwhich you press the brake pedal. It willprovide maximum braking efficiency aslong as you press the pedal. Emergencybrake assist can reduce stopping distancesin critical situations.
Trailer stability controlWARNINGS
Trailer stability control does notrelieve you of your responsibility totow with due care and attention.Disabling ESP will turn off thesystem.
Trailer stability control is an enhancedfeature of ESP, and automatically detectswhen an attached trailer starts to sway.If this situation occurs, the system willautomatically brake individual wheels tostabilise the trailer and vehicle. In case avery severe sway is detected, the enginetorque will be reduced and the vehicle willbe slowed automatically.
USING STABILITY CONTROLNote: The system will be switched onautomatically every time you switch theignition on.
100
Stability Control
Note: When the system is deactivated, thelamp will flash twice and remainsilluminated. Press the switch again toenable the system. For item location: SeeAt a Glance (page 9).
2-wheel drive vehiclesPress and hold the switch for one secondto deactivate Engine Traction Control,Trailer Stability Control and Brake TractionControl. Hill Start Assist remains active.
4-wheel drive vehiclesNote: All the stability control (ESP)functions are reactivated when 2H positionis selected.Transfer shift switch in 4H position:• Press and hold the switch for one
second to deactivate Engine TractionControl and Trailer Stability Control.Hill Descent Control, Hill Start Assistand Brake Traction Control remainactive.
Transfer shift switch in 4H or 4L position:• Press and hold the switch for five
seconds to deactivate Engine TractionControl, Trailer Stability Control andBrake Traction Control. Hill DescentControl and Hill Start Assist remainactive.
Transfer shift switch in 2H position:• Press and hold the switch for one
second to deactivate Engine TractionControl, Brake Traction Control andStability Control including TrailerStability Control. Hill Descent Controland Hill Start Assist remain active.
101
Stability Control
PRINCIPLE OF OPERATIONThe hill start assist system makes it easierto pull away when the vehicle is on a slopewithout the need to use the parking brake.When the system is active, the vehicle willremain stationary on the slope for a shorttime after you release the brake pedal.During this time, you have time to moveyour foot from the brake to the acceleratorpedal and pull away. The brakes arereleased automatically once the enginehas developed sufficient drive torque toprevent the vehicle from rolling down theslope. This is an advantage when pullingaway on a slope, for example from a carpark ramp, traffic lights or when reversinguphill into a parking space.
WARNINGThe system does not replace theparking brake. When you leave thevehicle, always apply the parking
brake and select first or reverse gear.
Note: Hill start assist is available in vehiclesequipped with electronic stabilityprogramme (ESP).
USING HILL START ASSISTThe system is activated automaticallywhen the vehicle is stopped on a slopegreater than 7% for automatictransmission vehicles and greater than 4%for manual transmission vehicles. Thesystem operates with the vehicle facingdownhill if reverse gear is selected andwith the vehicle facing uphill if any forwardgear is selected.
Activating the systemWARNINGS
You must remain in the vehicle onceyou have activated the system.
WARNINGSIn vehicles with automatictransmission, there is a short delayof up to two seconds after shifting
the lever to Drive or Reverse before the hillstart assist is activated. To avoid rollingdown in the slope, the foot brake shouldnot be released for up to two seconds.
The sytem is active unless ESPwarning lamp is turned off. At alltimes you are responsible for
controlling the vehicle, supervising thesystem and intervening, if required.
You can activate the system only if thefollowing conditions have been met:• The engine is running.• All doors are fully closed.• The parking brake is fully disengaged.• No failure mode is present.• Accelerator pedal is not depressed.• Vehicle is completely stopped.• Uphill: Gear shift lever should be in
position D for Automatic transmissionand in any position other than R(reverse) for manual transmission.
• Downhill: Gear shift lever should bein position R (reverse).
To activate the system:1. Press the brake and clutch pedals
(Manual transmission) to bring thevehicle to a complete standstill. Keepthe brake and clutch pedals (Manualtransmission) depressed.
2. If the sensors detect that the vehicle ison a slope the system will be activatedautomatically.
102
Hill Start Assist
3. When you remove your foot from thebrake pedal, the vehicle will remain onthe slope without rolling away for ashort time. This hold time willautomatically be extended if you arein the process of driving off.
4. Drive off in the normal manner. Thebrakes will be released automatically.
WARNINGIf the engine is revved excessively, orif a malfunction is detected when thesystem is active, the system will be
deactivated and ESP warning lamp willturn on.
Deactivating the systemTo deactivate the system, perform one ofthe following:• Apply the parking brake.• Open any door.• Drive off uphill without re-applying the
brake.• Wait for one to two seconds after you
remove your foot from the brake pedal.• If the system is active in a forward gear,
select reverse gear.• If the system is active in neutral,
release the clutch pedal (Manualtransmission).
• If the system is active in reverse gear,select neutral.
103
Hill Start Assist
PRINCIPLE OF OPERATION
WARNINGThe parking aid does not relieve youof your responsibility to drive withdue care and attention.
CAUTIONSVehicles fitted with a trailer towmodule not approved by us may notcorrectly detect obstacles.The sensors may not detect objectsin heavy rain or other conditions thatcause disruptive reflections.The sensors may not detect objectswith surfaces that absorb ultrasonicwaves.The parking aid does not detectobstacles moving away from thevehicle. They will only be detected
shortly after they start to move towardsthe vehicle again.
If you use a high pressure spray towash your vehicle, only spray thesensors briefly from a distance not
less than 20 centimetres (8 inches).Parking aid sends tones via the audiosystem fitted and approved by us. Ifthis is not working the parking aid
system will not work.
Note: On vehicles fitted with a tow ballarm, the rear parking aid is deactivatedautomatically when any trailer lamps (orlighting boards) are connected to the socketvia a trailer tow module we have approved.Note: Keep the sensors free from dirt, iceand snow. Do not clean with sharp objects.Note: The parking aid may emit false tonesif it detects a signal using the samefrequency as the sensors or if the vehicle isfully laden.
Note: The outer sensors may detect theside walls of a garage. If the distancebetween the outer sensor and the side wallremains constant for three seconds, thetone will switch off. As you continue, theinner sensors will detect rearward objects.
USING THE PARKING AID -VEHICLES WITH: REARPARKING AID
WARNINGThe parking aid does not relieve youof your responsibility to drive withdue care and attention.
E134605
The parking aid is automatically activatedwhen you select reverse gear with theignition switched on.Note: It will chime once to indicate that theparking aid is activated.Note: The indicator lamps will be displayedin the multi-function display. For itemlocation: See At a Glance (page 9).
104
Parking Aids
You will hear an intermittent tone at adistance of approximately 180 centimetres(71 inches) between the obstacle and rearbumper and approximately 50 centimetres(20 inches) to the side. Decreasing thedistance accelerates the intermittent tone.
A
E134606
Distance Indicator.A
As the distance decreases the indicatormoves towards the vehicle.A continuous tone will start at a distanceof less than 40 centimetres (15 inches) tothe rear bumper.
A
E134607
Malfunction indicator.ANote: If a malfunction is indicated thesystem will be disabled and a unique tonewill be heard. Have the system checked bya properly trained technician.
105
Parking Aids
E134608
A trailer symbol indicates there is a trailerattached and the system is disabled.
106
Parking Aids
PRINCIPLE OF OPERATIONThe camera is a visual aid for use whenreversing.
WARNINGThe system does not relieve you ofyour responsibility to drive with duecare and attention.
CAUTIONSIf you use a high pressure spray towash your vehicle, only spray thecamera briefly from a distance not
less than 20 centimetres (8 inches).Do not apply pressure to the camera.
Note: Keep the camera free from dirt, iceand snow. Do not clean with sharp objects,degreaser, wax or organic products. Use onlya soft cloth.During operation, guide lines appear in thedisplay which represent your vehicle's pathand approximate distance from rearwardobjects.
USING THE REAR VIEWCAMERA
WARNINGSThe operation of the camera mayvary depending on the ambienttemperature, vehicle and road
conditions.The distances shown in the displaymay differ from the actual distance.Do not place objects in front of thecamera.
The camera is located on the tail gatebelow the badge.
E133364
Activating the rear view cameraCAUTION
The camera may not detect objectsthat are close to the vehicle.
With the ignition unit switched on, engagereverse gear. The image is displayed on therear view mirror screen.The camera may not operate correctly inthe following conditions:• Dark areas.• Intense light.• If the ambient temperature increases
or decreases rapidly.• If the camera is wet, for example in rain
or high humidity.• If the camera's view is obstructed, for
example by mud.
Using the displayCAUTIONS
Obstacles above the camera positionwill not be shown. Inspect the areabehind your vehicle if necessary.Marks are for general guidance only,and are calculated for vehicles inmaximum load conditions on an even
road surface.
107
Rear view camera
A A
B
C
DE
E133365
Exterior mirror clearance - 0.1metre (4 inches)
A
Red - 0.3 metre (12 inches)BAmber - 1 metre (39 inches)C
Green - 2 metres (79 inches)DBlack - centre line of theprojected vehicle path
E
Note: When reversing with a trailer, the lineson the screen show the vehicle direction andnot the trailer.
Deactivating the rear view cameraNote: Disengage reverse gear. The displaywill stay on for a short period beforeswitching off.Note: The system will automatically switchoff once the vehicle speed has reachedapproximately 15 km/h (9 mph).
108
Rear view camera
PRINCIPLE OF OPERATION
WARNINGThe system does not relieve you ofyour responsibility to drive with duecare and attention.
Cruise control allows you to control yourspeed using the switches on the steeringwheel. You can use cruise control whenyou exceed approximately 40 km/h (25mph).
USING CRUISE CONTROL
WARNINGDo not use cruise control in heavytraffic, on twisty roads or when theroad surface is slippery.
Switching cruise control on
E102679
Note: The system is ready for you to set aspeed.
Setting a speed
E102680
Press to store and maintain your currentspeed. The cruise control indicator willilluminate. See Warning Lamps andIndicators (page 56).
Changing the set speedWARNING
When you are going downhill, yourspeed may increase above the setspeed. The system will not apply the
brakes. Change down a gear and press theSET- switch to assist the system inmaintaining the set speed.
Note: If you accelerate by pressing theaccelerator pedal, the set speed will notchange. When you release the acceleratorpedal, you will return to the speed that youpreviously set.
109
Cruise Control
E102681B
A
AccelerateADecelerateB
Cancelling the set speed
E102682
Press the brake pedal or the CAN RESswitch.Note: The system will no longer controlyour speed. The cruise control indicator willnot illuminate but the system will retain thespeed that you previously set.
Resuming the set speed
E102682
The cruise control indicator will illuminateand the system will attempt to resume thespeed that you previously set.
Switching cruise control off
E102683
The system will not retain the speed thatyou previously set. The cruise controlindicator will not illuminate.
110
Cruise Control
GENERAL INFORMATION
WARNINGSUse load securing straps to anapproved standard, e.g. DIN.Make sure that you secure all looseitems properly.Place luggage and other loads as lowand as far forward as possible withinthe luggage or loadspace.Do not exceed the maximum frontand rear axle loads for your vehicle.See Vehicle identification (page
162).Do not exceed the maximum grossvehicle weight stated on the vehicleidentification plate. See Vehicle
identification (page 162).
CAUTIONDo not allow items to contact the rearwindow.
TAILGATENote: The tailgate can be lowered forincreased access.
CAUTIONSAvoid placing excessive weight on thetailgate.Do not lower the tailgate completelyif a tow ball or a bumper is fitted.Make sure that you keep a firm grip ofthe tailgate to prevent it fromdropping down.
Lowering the tailgate
1
2
3E135868
Raise the tailgate slightly.1Pull the support cable rearwards.2Release the support cable fromtailgate.
3
Repeat steps 1 to 3 to pull outthe support cable on the otherside.
4
LOAD RETAINING FIXTURESRope hooksNote: The number of rope hooks may varydepending on your vehicle model.
Type 1
E131643
111
Load Carrying
Type 2
E133894
Type 3
CAUTIONThe maximum load per rope hook isstamped on the hook, do not exceedthis load.
E133896
Tie down points
A
B
CD
E134098
CleatABezelBSpringCPinD
WARNINGSTie down points are only to be usedfor restraining the loads within theloadspace. Using tie down points for
any other purpose may lead to seriousinjury or vehicle damage. Tie down pointsshould never be used for towing purposes.
Each tie down point has a maximumload rating. Exceeding this force maylead to serious injury and/or vehicle
damage.Always inspect the tie down pointsbefore use. Do not use the tie downpoints under the following
conditions:
• Tie down points show any sign of wearor damage.
• Rail channels supporting the tie downpoints show any sign of wear, damageor distortion.
112
Load Carrying
• Tie down point locking bezel isdamaged or broken or will not lock intoplace.
• Tie down point is not seated correctlywithin the support rail.
Fitting the tie down point
WARNINGBezel must be fully engage into therail to secure the tie down point forsafe use. The tie down is not
correctly installed even if the word underthe bezel “Not Locked” is partially visible.
1
2
E134099
1. Engage the base of the tie down pointinto the rail channel while holding thecleat vertically.
2. Slide along the rail until the pin on thebase of the tie down engages in adesired hole on the rail.
3. Push the tie down in and rotate aquarter turn clockwise until the tiedown cleat is horizontal and the lockingbezel “snaps” into place.
Removing the tie down point
A
BCE134100
1. Grasp the locking bezel between thethumb and fingers using the fingerrecess.
2. Pull the bezel away from the rail untilthe base of the tie down point is fullydisengaged from the rail channel.
3. Turn the tie down point a quarter turnanticlockwise until it snaps out of therail.
Load restWARNING
A loaded load rest alters the vehicle'scentre of gravity and aerodynamics.Take care when cornering, driving in
crosswinds and at high speeds.
113
Load Carrying
CAUTIONDo not exceed the permissible grossweight. See Vehicle IdentificationPlate (page 162).
E131682
Note: Secure luggage or cargo placed onthe load rest with the load rest stoppers.
ROOF RACKS AND LOADCARRIERSRoof rack
WARNINGSIf you use a roof rack, the fuelconsumption of your vehicle will behigher and you may experience
different driving characteristics.Read and follow the manufacturer’sinstructions when you are fitting aroof rack.
CAUTIONDo not exceed the maximumpermissible roof rail load of 75kilograms (165 pounds), including the
roof rack.
Check the security of the roof rack load asfollows:• before starting• after driving 50 kilometres (30 miles)• at 1000 kilometres (600 miles)
intervals.Note: To reduce fuel consumption, crossrails should be removed when not in use.
114
Load Carrying
A B C
E131684
Roof railASports barBBox railC
CAUTIONSDo not sit or stand on items B or C.
Do not use item C to secure loads.
115
Load Carrying
TOWING A TRAILER
WARNINGDo not exceed the maximum grosstrain weight stated on the vehicleidentification plate. See Vehicle
Identification Plate (page 162).
CAUTIONSMaximum permissible axle loads arenot to be exceeded while towing andtransporting.Do not exceed a speed of 100 km/h(62 mph) when towing with a ladenweight greater than 3000 kg (6613
lbs).
Note: Vehicles equipped with electronicstability programme (ESP) has trailerstability control. See Stability Control(page 100).Place loads as low and central to theaxle(s) of the trailer as possible. If you aretowing with an unladen vehicle, the loadin the trailer should be placed toward thenose, within the maximum nose load, asthis gives the best stability.The stability of the vehicle to trailercombination is very much dependant onthe quality of the trailer.The maximum vehicle and trailer payloadsrepresent technically binding values forgradients up to 12% and at an altitude of1000 meters (3281 feet) above sea level.In high altitude regions, thinner atmospherecan reduce performance so the followingrestrictions will apply:
In high altitude regions above 1000 meters(3281 feet), the stipulated maximumpermitted gross train weight must bereduced by 10% for every additional 1000meters (3281 feet).
Steep gradientsWARNING
The overrun brake on a trailer is notcontrolled by the anti-lock brakingsystem.
Change down a gear before you reach asteep downhill gradient.
Trailer tow moduleNote: Ensure that the indicator and brakelamps do not flicker with engine runningwhile using a trailer with low power LEDlamps.To overcome flickering and to ensure thecorrect operation of the rear parking aid, atrailer patch harness should be connectedbetween the trailer and the vehicle.
CAUTIONDo not connect the trailer patchharness to the vehicle when the traileris not connected.
Note: The trailer patch harness is availablewith the Ford authorised dealers.
116
Towing
Technical specificationsTowing capacities
Trailer noseweight kg
(lbs)
With trailerbrake kg
(lbs)
Withouttrailer brake
kg (lbs)
TransmissionDriveVariant
165 (364)2200 (4850)750 (1653.5)Manual4X22.5L Petrol
225 (496)1700 (3748)750 (1653.5)Manual4x2*
225 (496)1100 (2425)750 (1653.5)Manual4x4
165 (364)2200 (4850)750 (1653.5)Manual4X22.2L Diesel88kW &
92kW 225 (496)1600 (3527)750 (1653.5)Manual4x2*
225 (496)1600 (3527)750 (1653.5)Manual4x4
165 (364)2500 (5511)750 (1653.5)Manual4x22.2L Diesel110kW
225 (496)1800 (3968)750 (1653.5)Manual4x2 *Drive ratio
3.31
225 (496)3350 (7385)750 (1653.5)Manual4x2 *Drive ratio
3.55
225 (496)3350 (7385)750 (1653.5)Auto4x2 *
225 (496)3350 (7385)750 (1653.5)Manual andAuto
4x4
225 (496)1800 (3968)750 (1653.5)Manual4x2 * and4x4
3.2L Diesel
Drive ratio3.31
225 (496)3350 (7385)750 (1653.5)Manual4x2* and 4x4Drive ratio
3.55
225 (496)3350 (7385)750 (1653.5)Auto4x2*
225 (496)3350 (7385)750 (1653.5)Auto4x4*Vehicles with increased ride height
117
Towing
TOW BALL
WARNINGSNever leave the detached tow ballarm unsecured inside the vehicle.This would increase the risk of injury
in an accident.When not in use, always transportthe tow ball arm securely fastenedin the luggage compartment.Take special care when fitting thetow ball arm as the safety of thevehicle and the trailer depends on
this.Do not modify the trailer coupling.
Do not disassemble or repair the towball arm.
A trailer socket and the tow ball arm seatare provided underneath the rear bumper.Turn the trailer socket down through 90degrees until it engages in the correctposition.
4x2Inserting the tow ball arm
E137325
1. Insert the tow ball arm in to the seat.
WARNINGMake sure that the tow ball arm isfully engaged in the seat.
Driving with a trailer
E138394
WARNINGIf any of the following conditionscannot be met, do not use the towbar and have it inspected by properly
trained technicians.
Before starting your journey, make surethat:• The tow ball is correctly locked.• The tow ball arm is fully engaged in its
seat.
118
Towing
Removing the tow ball arm
1
2
3E137326
1. Push the lever towards the centre ofthe vehicle.
2. Turn the lever anti-clockwise to unlockthe tow ball arm.
3. Remove the tow ball arm.
4x2 (vehicles with increased rideheight) and 4x4
E139242
Tighten the bolts to 218 ± 42 Nm.
Driving without a trailer1. Remove the tow ball arm.2. Install the plug into its seat.
WARNINGSTo avoid risk of injury, never unlockthe tow ball arm with the trailerattached.Remove the tow ball when drivingwithout a trailer.
MaintenanceKeep the system clean.Periodically lubricate the tow ballmechanism with resin-free grease or oiland the lock with graphite.
119
Towing
GENERAL DRIVING POINTSVehicles with a diesel engineIf the low fuel level warning lamp comeson, refuel as soon as possible. If youcontinue driving without refuelling, theengine will start to run unevenly. Thisindicates that you are about to run out offuel. Refuel immediately.
RUNNING-INTyres
WARNINGNew tyres need to be run-in forapproximately 500 kilometres (300miles). During this time, you may
experience different driving characteristics.
Brakes and clutchWARNING
Avoid heavy use of the brakes andclutch if possible for the first 150kilometres (100 miles) in town and
for the first 1500 kilometres (1000 miles)on motorways.
EngineCAUTION
Avoid driving too fast during the first1500 kilometres (1000 miles). Varyyour speed frequently and change up
through the gears early. Do not labour theengine.
COLD WEATHERPRECAUTIONSThe functional operation of somecomponents and systems can be affectedat temperatures below -30°C (-22°F).
REDUCED ENGINEPERFORMANCEYour vehicle can be driven briefly if theengine overheats, without damage to theengine. The engine will continue to operatewith limited power. The distance you cantravel depends on ambient temperature,vehicle load, and terrain.If the needle moves to the upper limitposition, the engine is overheating. SeeGauges (page 56).If the temperature continues to rise, thefuel supply to the engine will be reduced.The air conditioning (if fitted) will also beturned off and the engine cooling fan willoperate.
CAUTIONContinued operation will increase theengine temperature, and cause theengine to shut down completely.
• Stop your vehicle as soon as possible.• Immediately turn off the engine to
prevent severe engine damage.• Wait for the engine to cool down.• Check the coolant level. See Engine
Coolant Check (page 144).• Have the vehicle checked by an expert
immediately.
120
Driving Hints
DRIVING THROUGH WATERDriving through water
WARNINGNever cross fast-flowing deepstreams, as your vehicle could beswept away.
CAUTIONSDrive through water in an emergencyonly, and not as part of normal driving.Engine damage can occur if waterenters the air filter.Always try to determine the depth ofa crossing before driving the vehiclethrough.
In an emergency, the vehicle can be driventhrough water to a maximum depth asshown and at a maximum speed of 7 km/h(4 mph). Extra caution should be exercisedwhen driving through flowing water.4X2
X
E137140
600 mm (23.6 inches)X
4x2 (vehicles with increased rideheight) and 4x4
Y
E137139
800 mm (31.5 inches)Y
When driving in water, engage first gearand low range (if available), maintain asteady walking pace speed keeping thebow wave in front of the vehicle and donot stop. After driving through water, andas soon as it is safe to do so:• Depress the brake pedal lightly and
check that full brake function isachieved.
• Check that the horn works.• Check that the vehicle's lights are fully
operational.• Check the power assistance of the
steering system.
121
Driving Hints
FIRST AID KITNote: First aid kit is secured in thepassenger side storage compartment.
E131836
WARNING TRIANGLESingle cabA retaining strap behind the passenger seatcan be used to secure a warning triangle.
E131837
Fold the seatback forward.1
Stretch cabNote: The warning triangle can be securedin the tool bin below the rear seats.
E131838
Remove the rear seat cushion.1Remove the cover.2
122
Roadside Emergencies
FUSE BOX LOCATIONSLeft-hand drive
B
A
E132740
Right-hand drive
B
A
E132741
Passenger compartment fusebox
A
Engine compartment fuse boxB
Passenger compartment fuse boxFully open the driver's side storagecompartment.
1
2
E133080
E134659
124
Fuses
Engine compartment fuse box
E133079
Release the catches and remove the cover.
CHANGING A FUSE
WARNINGSDo not modify the electrical systemof your vehicle in any way. Haverepairs to the electrical system and
the replacement of relays and high currentfuses carried out by properly trainedtechnicians.
Switch the ignition and all electricalequipment off before touching orattempting to change a fuse.
CAUTIONFit a replacement fuse with the samerating as the one you have removed.
Note: You can identify a blown fuse by abreak in the filament.Note: All fuses, except high current fuses,are a push fit.
125
Fuses
FUSE SPECIFICATION CHARTEngine compartment fuse box
E133601
Circuits protectedAmpereratingFuse
Passenger compartment fuse box supply (battery)601
Passenger compartment fuse box supply (Ignition)602
Engine cooling fan503 (Petrol)
Glow plug control module603 (Diesel)
ABS module404
Electric windows (front and rear)305
126
Fuses
Circuits protectedAmpereratingFuse
Four wheel drive (4WD) motor ground256
Not used-7
Not used-8
Electric seat209
Electric windows (front)3010
Blower motor3011
Four wheel drive (4WD) motor power2512
Starter solenoid2013
Heated rear window2014
Flex-fuel pump1015 (Petrol)
Vapouriser glow plug1515 (Diesel)
A/C Clutch1016
Electric windows (front)2517
Windscreen wiper motor2018
Windscreen wiper motor ground2019
Cigar lighter2020
Horn1521
Fuel injectors or flex-fuel valve1522
Differential lock solenoid1023
Auxillary power socket2024
Ignition coils, Temperature and Mass Air Flow sensor, Glowplug module, Vacuum Control Valve (VCV), ElectronicVacuum Regulator Valve (EVRV)
1525
Electronic control module (ECM)7.526
Transmission control module (TCM)1027
Heated exhaust gas oxygen, Universal Heated ExhaustGas Oxygen-sensor, Relay coils, Fuel cut off switch1028
127
Fuses
Circuits protectedAmpereratingFuse
Electronic control module (ECM)1529
Battery monitoring sensor1530
Auxillary power socket (rear console)2031
A/C pressure switch532
Transmission control module (TCM)1033
Not used-34
Passenger compartment fuse box supply (Ignition)2035
ABS module536
Headlamp levelling1037
Heated seat2038
Power mirrors1039
Vapouriser pump1040
Heated mirrors1041
Alarm horn1042
Heated windscreen (right)3043
Heated windscreen (left)3044
ABS module2545
Auxillary power socket (bedliner)2046
Trailer tow module4047
Not used-48
Not used-49
Ignition relay, Relay coils550
Electric windows (rear)3051 (Brazilonly)
Trailer tow (12 or 13 pin battery feed, Permanent live)2051
128
Fuses
Circuits switchedRelay
Key interlockR1
Wiper on or offR2
HornR3
A/C clutchR4
Differential lockR5
Wiper Hi or LoR6
Engine cooling fan lowR7
Engine cooling fan highR8
Flex-fuel pump, Vapouriser glow plugR9
Heated rear windowR10
Heated windscreenR11
Not usedR12
Electronic control module (ECM) powerhold
R13
IgnitionR14
4WD motor 2 (Clockwise)R15
4WD motor 1 (Counter clockwise)R16
4WD motorR17
Security hornR18
Starter motorR19
Not usedR20
Not usedR21
Not usedR22
Not usedR23
Not usedR24
Not usedR25
Blower motorR26
129
Fuses
Circuits protectedAmpere ratingFuse
Fuel pump2056
Not used-57
Not used-58
Passive anti-theft system(PATS)559
Interior lamp, driver's doorswitch pack, mood lights,puddle lights, Automaticshifter, footwell lamp
1060
Not used-61
Rain sensor module562
Tachograph563
Not used-64
Not used-65
Driver's door lock, centraldouble locking2066
Stop lamp switch567
Not used-68
Instrument cluster, Integ-rated control module (ICP),Tracking and blockingmodule
569
Central locking2070
Air conditioning571
Alarm horn7.572
On-board diagnostics II573
Main beam2074
Front fog lamps1575
Reversing lamp, rear viewmirror1076
132
Fuses
Circuits protectedAmpere ratingFuse
Washer pump2077
Ignition switch578
Radio1579
Multi-function display, Hiaudio, Brake Valve Closing(BVC) module
2080
Interior motion sensor581
Washer pump ground2082
Central locking ground2083
Driver's door lock, centraldouble locking ground2084
Instrument cluster, Parkingaid module, Rear viewcamera, Manual air condi-tioning, Rear view mirror
7.585
Restraint system, Passengerair-bag deactivation switch1086
Tachograph587
Not used-88
Not used-89
133
Fuses
TOWING POINTSNote: The second front towing eye isoptional.Note: If the rear towing eye is not fitted, therecommended towing point is the left orright hand side rear suspension shackle.
B
A
E131731
Front towing eyeARear towing eyeB
TOWING THE VEHICLE ONFOUR WHEELSAll vehicles
WARNINGSSwitch the ignition on when yourvehicle is being towed. The steeringlock will engage and the direction
indicators and brake lamps will not workif you do not.
WARNINGSThe brake servo and the powersteering pump do not operate unlessthe engine is running. Press the brake
pedal harder and allow for increasedstopping distances and heavier steering.
CAUTIONSToo much tension in the tow ropecould cause damage to your vehicleor the vehicle that is towing.2WD: Select neutral when yourvehicle is being towed.4WD: In the event of a breakdown ora mechanical failure of thetransmission your vehicle must be
recovered with either ALL wheels off theground or transported with ALL wheels onthe ground while the vehicle is in 2WDmode. Under no circumstances should thevehicle be towed with ALL wheels on theground when in 4WD mode.
Drive off slowly and smoothly withoutjerking the vehicle that is being towed.
Vehicles with automatictransmission
CAUTIONSIt is recommended not to tow with thedrive wheels on the ground. However,if it is required to move the vehicle
from a dangerous location, do not tow yourvehicle faster than 80 km/h (50 mph) orfurther than 80 kilometers (50 miles).
In the event of a mechanical failure ofthe transmission the drive wheelsmust be lifted clear of the ground.
134
Vehicle recovery
GENERAL INFORMATIONHave your vehicle serviced regularly to helpmaintain its roadworthiness and resalevalue. There is a large network of FordAuthorised Repairers that are there to helpyou with their professional servicingexpertise. We believe that their speciallytrained technicians are best qualified toservice your vehicle properly and expertly.They are supported by a wide range ofhighly specialised tools developedspecifically for servicing your vehicle.In addition to regular servicing, werecommend that you carry out thefollowing additional checks.
WARNINGSSwitch the ignition off beforetouching or attempting adjustmentof any kind.Do not touch the electronic ignitionsystem parts after you have switchedthe ignition on or when the engine is
running. The system operates at highvoltage.
Keep your hands and clothing clearof the engine cooling fan. Undercertain conditions, the fan may
continue to run for several minutes afteryou have switched the engine off.
CAUTIONWhen carrying out maintenancechecks, make sure that filler caps arefitted securely.
Daily checks• Exterior lamps.• Interior lamps.• Warning lamps and indicators.
Check when refuelling• Engine oil level. See Engine Oil Check
(page 143).• Brake fluid level. See Brake and
Clutch Fluid Check (page 145).• Washer fluid level. See Washer Fluid
Check (page 146).• Tyre pressures (when cold). See
Technical Specifications (page 161).• Tyre condition. See Tyre Care (page
160).
Monthly checks• Engine coolant level (engine cold). See
Engine Coolant Check (page 144).• Pipes, hoses and reservoirs for leaks.• Power steering fluid level. See Power
Steering Fluid Check (page 145).• Air conditioning operation.• Parking brake operation.• Horn operation.• Tightness of wheel nuts. See
Technical Specifications (page 161).
OPENING AND CLOSING THEBONNETOpening the bonnet
1
E131809
135
Maintenance
1. Pull the lever under the instrumentpanel. For item location: See At aGlance (page 9).
3
2
4
E131810
2. Raise the bonnet slightly.3. Move the catch towards the left-hand
side of the vehicle.4. Open the bonnet.
E131811
5. Support it with the strut.
Closing the bonnetNote: Make sure that the bonnet is closedproperly.Lower the bonnet and allow it to drop fromunder its own weight for the last 20 – 30centimetres (8 - 11 inches).
136
Maintenance
UNDER BONNET OVERVIEW - 2.5L DURATEC-HE (122KW/165PS)- MI4RHD
I H G
FA EB C D
JE131919
137
Maintenance
LHD
H G
FA EBC D
IJE131920
Engine coolant reservoir cap. See Engine Coolant Check (page 144).ABrake and clutch fluid reservoir cap. See Brake and Clutch Fluid Check (page145).
B
Engine oil filler cap1. See Engine Oil Check (page 143).CEngine oil dipstick1. See Engine Oil Check (page 143).DEngine junction box. See Fuses (page 124).EVehicle Identificaton Plate. See Vehicle identification (page 162).FBattery. See Vehicle battery (page 152).GPower steering fluid reservoir cap. See Power Steering Fluid Check (page145).
H
Air Cleaner.IWasher fluid reservoir cap. See Washer Fluid Check (page 146).J
1 The filler caps and the engine oil dipstick are coloured for easy identification.
138
Maintenance
UNDER BONNET OVERVIEW - 2.2L DURATORQ-TDCI (PUMA)DIESELRHD
H
F GA EB C D
K IJE131930
139
Maintenance
LHD
H
F GA E BC D
K IJE131931
Engine coolant reservoir cap. See Engine Coolant Check (page 144).ABrake and clutch fluid reservoir cap. See Brake and Clutch Fluid Check (page145).
B
Engine oil dipstick1. See Engine Oil Dipstick (page 143).CEngine oil filler cap1. See Engine Oil Check (page 143).DFuel filter water trap. See Draining the Fuel Filter Water Trap (page 145).EEngine junction box. See Fuses (page 124).FVehicle Identificaton Plate. See Vehicle identification (page 162).GBattery. See Vehicle battery (page 152).HPower steering fluid reservoir cap. See Power Steering Fluid Check (page145).
I
140
Maintenance
Washer fluid reservoir cap. See Washer Fluid Check (page 146).JAir Cleaner.K
1 The filler caps and the engine oil dipstick are coloured for easy identification.
UNDER BONNET OVERVIEW - 3.2L DURATORQ-TDCI (PUMA)DIESELRHD
H
F GA EB C D
K IJE131967
141
Maintenance
LHD
H
F GA E BC D
K IJE131968
Engine coolant reservoir cap. See Engine Coolant Check (page 144).ABrake and clutch fluid reservoir cap. See Brake and Clutch Fluid Check (page145).
B
Engine oil dipstick1. See Engine Oil Dipstick (page 143).CEngine oil filler cap1. See Engine Oil Check (page 143).DFuel filter water trap. See Draining the Fuel Filter Water Trap (page 145).EEngine junction box. See Fuses (page 124).FVehicle Identificaton Plate. See Vehicle identification (page 162).GBattery. See Vehicle battery (page 152).HPower steering fluid reservoir cap. See Power Steering Fluid Check (page145).
I
142
Maintenance
Washer fluid reservoir cap. See Washer Fluid Check (page 146).JAir Cleaner.K
1 The filler caps and the engine oil dipstick are coloured for easy identification.
ENGINE OIL DIPSTICK - 2.5LDURATEC-HE (122KW/165PS)- MI4
E92036
A B
MINAMAXB
ENGINE OIL DIPSTICK - 2.2LDURATORQ-TDCI (PUMA)DIESEL/3.2L DURATORQ-TDCI(PUMA) DIESEL
E71362
A B
MINAMAXB
ENGINE OIL CHECK
CAUTIONDo not use oil additives or otherengine treatments. Under certainconditions, they could damage the
engine.
Note: The oil consumption of new enginesreaches its normal level after approximately5000 kilometres (3000 miles).
Checking the oil levelCAUTION
Make sure that the level is betweenthe MIN and the MAX marks.
Note: Check the level before starting theengine.Note: Make sure that your vehicle is on levelground.Note: Oil expands when it is hot. The levelmay therefore extend a few millimetresbeyond the MAX mark.Remove the dipstick and wipe it with aclean, lint free cloth. Replace the dipstickand remove it again to check the oil level.If the level is at the MIN mark, top upimmediately.
Topping upWARNINGS
Only top up when the engine is cold.If the engine is hot, wait 10 minutesfor the engine to cool down.
143
Maintenance
WARNINGSDo not remove the filler cap whenthe engine is running.
Remove the filler cap.WARNING
Do not top up further than the MAXmark.
Note: Soak up any spillage with anabsorbent cloth immediately.Top up with fluid that meets the Fordspecification. See TechnicalSpecifications (page 146).Replace the filler cap. Turn it until you feela strong resistance.
ENGINE COOLANT CHECKChecking the coolant level
WARNINGDo not allow the fluid to touch yourskin or eyes. If this happens, rinse theaffected areas immediately with
plenty of water and contact your doctor.
CAUTIONMake sure that the level is betweenthe MIN and the MAX marks.
Note: Coolant expands when it is hot. Thelevel may therefore extend beyond the MAXmark.If the level is at the MIN mark, top upimmediately.
Topping upWARNINGS
Only top up when the engine is cold.If the engine is hot, wait 10 minutesfor the engine to cool down.Do not remove the filler cap whenthe engine is running.Do not remove the filler cap whenthe engine is hot. Wait for the engineto cool down.Undiluted coolant is flammable andmay ignite if spilt on a hot exhaust.
CAUTIONSIn an emergency, you can add justwater to the cooling system to reacha vehicle service station. Have the
system checked by a properly trainedtechnician as soon as possible.
Prolonged use of incorrect dilution ofthe coolant can cause engine damagefrom corrosion, overheating or
freezing.
Unscrew the cap slowly. Any pressure willescape slowly as you unscrew the cap.
CAUTIONDo not top up further than the MAXmark.
Top up with a 50/50 mixture of coolantand water using fluid that meets the Fordspecification. See TechnicalSpecifications (page 146).
144
Maintenance
POWER STEERING FLUIDCHECK
WARNINGDo not allow the fluid to touch yourskin or eyes. If this happens, rinse theaffected areas immediately with
plenty of water and contact your doctor.
CAUTIONMake sure that the level is betweenthe MIN and the MAX marks.
If the level is at the MIN mark, top upimmediately.
Topping upRemove the filler cap.
CAUTIONDo not top up further than the MAXmark.
Top up with fluid that meets the Fordspecification. See TechnicalSpecifications (page 146).
BRAKE AND CLUTCH FLUIDCHECK
WARNINGSUse of any fluid other than therecommended brake fluid mayreduce brake efficiency and not meet
Ford's performance standards.Do not allow the fluid to touch yourskin or eyes. If this happens, rinse theaffected areas immediately with
plenty of water and contact your doctor.
WARNINGSIf the level is at the MIN mark, havethe system checked by a properlytrained technician as soon as
possible.
Note: Keep brake fluid clean and dry.Contamination with dirt, water, petroleumproducts or other materials may result inbrake system damage and possible failure.Note: The brake and the clutch systems aresupplied from the same reservoir.Top up with fluid that meets the Fordspecification. See TechnicalSpecifications (page 146).
DRAINING THE FUEL FILTERWATER TRAP
WARNINGDo not dispose of diesel in householdrefuse or the public sewage system.Use your local authorised waste
disposal facilities.
Note: Only add fuel that meets the Fordspecification. See Fuel Quality (page 87).Note: The in-tank pump will turn offautomatically after approximately 40seconds.
145
Maintenance
E131831
For item location: See Under BonnetOverview (page 139). See Under BonnetOverview (page 141).1. Switch the ignition off.2. Connect and secure a suitable hose on
the filter drain plug.3. Route the other end of the hose to the
suitable container.
4. Loosen the drain plug by approximately1.5 turns.
5. Switch the ignition on to activate thein-tank pump.
6. Drain the water till it is replaced by aclean diesel fuel.
7. Switch the ignition off.8. Tighten the drain plug and remove the
hose.9. Start the engine and check for leaks.Note: The water-in-fuel indicator lamp willgo out after approximately 2 seconds, withthe engine running.
WASHER FLUID CHECKTop up the washer fluid reservoir when thewasher fluid level indicator is on. SeeWarning Lamps and Indicators (page56).When topping up, use a mixture of washerfluid and water to help prevent freezing incold weather and improve the cleaningcapability. We recommend that you useonly high quality washer fluid.
TECHNICAL SPECIFICATIONSVehicle fluids
SpecificationRecommended fluidPart
WSS-M2C-913-CCastrol Engine Oil*Engine oil - Diesel (formarkets with low sulphur
contentless than 350 ppm)
WSS-M2C-921-ACastrol Engine Oil**Engine oil - Diesel (formarkets with high sulphur
contentgreater than 350 ppm)
WSS M2C913-CCastrol Engine Oil ***Engine oil - PetrolWSS-M2C929-A
146
Maintenance
SpecificationRecommended fluidPart
WSS M2C930-AWSS M2C946-AWSS M2C945-A
WSD-M2C200-CCastrol - BOT130-MTransmission oil - Manual(MT-75)
WSS-M2C200-D2Castrol - BOT350-M3Transmission oil - Manual(MT-82)
WSS-M2C938-A (XT-10QLV)
Motorcraft MERCON® LVTransmission oil - Auto-matic
WSS-M6C65-A2 SuperDot4-14M
Clutch/Brake
WSS-M2C938-A (XT-10QLV)
Motorcraft MERCON® LVPower assisted steering
WSS-M97B44-D (XLC-0F02)
Chevron / ArtecoCoolant
WSP-M2C197-AFront Axles
WSL-M2C192-ACastrolRear Axles
WSS-M2C938-A (XT-10QLV)
Motorcraft MERCON® LVTransfer Case
WSH-M17B19-AR134ARefrigerant
WSH-M1C231-BPOLYALKYLENE GLYCOLAC Compressor lubricant* Initial fill is European oil WSS-M2C-913-C in all plants. For high sulphur markets changeengine oil at first service interval to WSS-M2C-921-A.Your engine has been designed to be used with Castrol and Ford Engine Oil, which givesa fuel economy benefit whilst maintaining the durability of your engine.Engine oil - Diesel (for markets with low sulphur content less than 350 ppm): Ifyou are unable to find an oil that meets the specification defined by WSS-M2C913-C,you must use SAE 5W-30 (preferred), SAE 5W-40 or SAE 10W-40 that meets thespecification defined by either ACEA A5/B5 (preferred) or ACEA A3/B3.**Engine oil - Diesel (for markets with high sulphur content greater than 350 ppm):If you are unable to find an oil that meets the specification defined by WSS-M2C921-A,you must use SAE 10W-30 (preferred), SAE 5W-40 or SAE 10W-40 that meets thespecification defined by either ACEA E5-99 or API CH-4 or higher.
147
Maintenance
***For petrol engines only, If you are unable to find an oil that meets the specificationdefined in the vehicle fluids table, you must use SAE 5W-20 or SAE 5W-30 that meetsthe specification defined by either ACEA A5-B5, API SM or API SN.Using topping up oils other than the one specified can result in longer engine crankingperiods, reduced engine performance, reduced fuel economy and increased emissionlevels.Castrol engine oil recommended.
E115472
Capacities
Capacity in Litres (gallons)ItemVariant
1.2 (0.26)Power assisted steeringfluidAll
5.5 (1.2)Windscreen washer systemAll
80 (17.60)Fuel tankAll
10.5 (2.31)Transmission fluidAutomatic transmission(dry)
9 (1.97)Transmission fluidAutomatic transmission(wet)
1.7 (0.37)Transmission fluidManual transmission(MT75)
2.7 (0.59)Transmission fluidManual transmission(MT82)
8.6 (1.89)Engine oil - with filter2.2L DuraTorq-TDCi
11.5 (2.53)Cooling system2.2L DuraTorq-TDCi (MT75& MT82)
Information not availableCooling system2.2L DuraTorq-TDCi (AT)
9.75 (2.14)Engine oil - with filter3.2L DuraTorq-TDCi
12.9 (2.84)Cooling system3.2L DuraTorq-TDCi (MT82)
13.5 (2.97)Cooling system3.2L DuraTorq-TDCi (AT)
6.7 (1.47)Engine oil - with filter2.5L Duratec-HE
148
Maintenance
CLEANING THE EXTERIOR
WARNINGIf you use a car wash with a waxingcycle, make sure that you remove thewax from the windscreen.
CAUTIONSPrior to using a car wash facility checkthe suitability of it for your vehicle.Some car wash installations usewater at high pressure. This coulddamage certain parts of your vehicle.Remove the aerial before using anautomatic car wash.Switch the heater blower off toprevent contamination of the fresh airfilter.
We recommend that you wash your vehiclewith a sponge and lukewarm watercontaining a car shampoo.
Cleaning the headlampsCAUTIONS
Do not scrape the headlamp lensesor use abrasives, alcoholic solvents orchemical solvents to clean them.Do not wipe the headlamps whenthey are dry.
Cleaning the rear windowCAUTION
Do not scrape the inside of the rearwindow or use abrasives or chemicalsolvents to clean it.
Use a clean, lint free cloth or a dampchamois leather to clean the inside of therear window.
Cleaning the chrome trimCAUTION
Do not use abrasives or chemicalsolvents. Use soapy water.
Body paintwork preservationCAUTIONS
Do not polish your vehicle in strongsunshine.Do not allow polish to touch plasticsurfaces. It could be difficult toremove.Do not apply polish to the windscreenor rear window. This could cause thewipers to become noisy and they may
not clear the window properly.
We recommend that you wax thepaintwork once or twice a year.
CLEANING THE INTERIORSeat belts
WARNINGSDo not use abrasives, or chemicalsolvents to clean them.Do not allow moisture to penetratethe seat belt retractor mechanism.
Clean the seat belts with interior cleaneror water applied with a soft sponge. Letthe seat belts dry naturally, away fromartificial heat.
150
Vehicle Care
Instrument cluster screens, LCDscreens, radio screens
WARNINGDo not use abrasives, alcoholicsolvents or chemical solvents toclean them.
Rear windowsCAUTIONS
Do not use any abrasive materials toclean the interior of the rear windows.Do not install stickers or labels to theinterior of the rear windows.
REPAIRING MINOR PAINTDAMAGE
CAUTIONRemove apparently harmless lookingsubstances from the paintworkimmediately (e.g. bird droppings, tree
resins, insect remains, tar spots, road saltand industrial fall out).
You should repair paintwork damagecaused by stones from the road or minorscratches as soon as possible. A choice ofproducts is available from your FordDealer. Read and follow themanufacturer’s instructions.
151
Vehicle Care
JUMP-STARTING THE VEHICLE
CAUTIONSConnect batteries with only the samenominal voltage.Always use booster cables withinsulated clamps and adequate sizecable.Do not disconnect the battery fromthe vehicle’s electrical system.
To connect the booster cables
A
C
D
B
E131788
Flat battery vehicleABooster battery vehicleBPositive connection cableCNegative connection cableD
1. Position the vehicles so that they donot touch one another.
2. Switch off the engine and any electricalequipment.
3. Connect the positive (+) terminal ofvehicle B with the positive (+) terminalof vehicle A (cable C).
4. Connect the negative (-) terminal ofvehicle B to the ground connection ofvehicle A (cable D). See Batteryconnection points (page 153).
CAUTIONSDo not connect to the negative (–)terminal of the flat battery.Make sure that the cables are clear ofany moving parts.
To start the engine1. Run the engine of vehicle B at
moderately high speed.2. Start the engine of vehicle A.3. Run both vehicles for a minimum of
three minutes before disconnecting thecables.
CAUTIONDo not switch on the headlamps whendisconnecting the cables. The peakvoltage could blow the bulbs.
Disconnect the cables in the reverse order.
152
Vehicle battery
BATTERY CONNECTIONPOINTS
E133362
CAUTIONDo not connect to the negative (–)terminal of the flat battery.
BATTERY WARNING SYMBOLSBattery lables
E135613
No smoking, no naked flames,no sparks.
E135614
Shield the eyes.
E135615
Keep away from children.
E135616
Corrosive.
i
E135617
Note operating instructions.
E135618
Explosive gas.
153
Vehicle battery
GENERAL INFORMATION
CAUTIONSUse only approved wheel and tyresizes. Using other sizes could damagethe vehicle and will make the National
Type Approval invalid.If you change the diameter of the tyresfrom that fitted at the factory, thespeedometer may not display the
correct speed. Take the vehicle to yourdealer to have the engine managementsystem reprogrammed.
If you intend to change the size of thewheels from that fitted at the factory,check the suitability with your dealer.
Note: Check your tyre pressures regularlyto optimise fuel economy.A decal with tyre pressure data is locatedin the driver’s door opening at the B-pillar.Check and set the tyre pressure at theambient temperature in which you areintending to drive the vehicle and when thetyres are cold.
CHANGING A ROAD WHEELLocking wheel nutsYou can obtain a replacement lockingwheel nut key and replacement lockingwheel nuts from your dealer using thereference number certificate.
Vehicle jackWARNINGS
The vehicle jack supplied with yourvehicle should only be used whenchanging a wheel in emergency
situations.
WARNINGSBefore using the vehicle jack, checkthat it is not damaged or deformedand that the thread is lubricated and
free from foreign matter.Never place anything between thejack and the ground, or the jack andthe vehicle.
It is recommended to use a workshop typehydraulic jack for changing betweensummer and winter tyres.Note: Use a jack with a minimum liftingcapacity of one tonne (one ton) and a liftingplate with a minimum diameter of 80millimetres (3.1 inches).The jack, wheel brace, and jack handle arelocated in the cab.
Single cab
E133591
154
Wheels and Tyres
E135841
1. Fold the LH seatback forward.2. Remove the locking strap and remove
the tools.3. Fold the RH seatback forward.4. Loosen the jack, remove the bolt and
remove the jack.
Stretch cab
E134701
E131838
4
5
E133592
1. Pull the release strap.2. Remove the rear seats.3. Remove the cover and loosen the jack.4. Remove the bolt.5. Remove the jack.6. Remove the tools.
155
Wheels and Tyres
Double cab
1
2
E133593
1. Lift the release strap.2. Lower the seatback.3. Remove the locking strap.4. Loosen the jack and remove the bolt.5. Remove the jack.
Spare wheelNote: Your vehicle may exhibit someunusual driving characteristics.The spare wheel is located underneath therear of the vehicle.
1 2
3
E79153
E133589
E133590
1. Assemble the handle.2. Fully insert the jack handle into the
guide hole. Turn anti-clockwise untilthe wheel rests on the ground, andthere is slack in the cable.
3. Pass the bracket and cable through thewheel opening.
156
Wheels and Tyres
Jacking and lifting points CAUTIONUse only the specified jacking points.If you use other positions, you maydamage the body, steering,
suspension, engine, braking system or thefuel lines.
B
A
E133594
Emergency use onlyAMaintenanceB
157
Wheels and Tyres
E134692
Removing a road wheelWARNINGS
Park your vehicle in such a positionthat neither the traffic nor you arehindered or endangered.Turn on the hazard warning flasher.
Set up a warning triangle.
Make sure that the vehicle is on firm,level ground with the wheels pointingstraight ahead.Switch off the ignition and apply theparking brake.If your vehicle has a manualtransmission, select first or reversegear. If it has an automatic
transmission, select park.Have the passengers leave thevehicle.Always secure the diagonallyopposite wheel with an appropriateblock or wheel chock when changing
a wheel.
WARNINGSOnly use the vehicle jack to changea wheel. Never work underneath thevehicle when it is supported only by
the jack.Make sure that the jack is vertical tothe jacking point and the base is flaton the ground.
CAUTIONDo not lay alloy wheels face down onthe ground, this will damage the paint.
1 2
3
E79153
Note: Three handles need to be assembledwhen jacking the rear of the vehicle.1. Assemble the jack handle.2. Slacken the wheel nuts.3. Jack up the vehicle until the tyre is clear
of the ground.
158
Wheels and Tyres
E134693
4. Unscrew and remove the wheel nutsand take off the wheel.
Installing a road wheelWARNINGS
Use only approved wheel and tyresizes. Using other sizes coulddamage the vehicle and will void the
warranty. See Technical Specifications(page 161).
Do not fit run flat tyres on vehiclesthat were not originally fitted withthem. Please contact your dealer for
more details regarding compatibility.Make sure that there is no lubrication(grease or oil) on the threads or theinterface between wheel studs and
nuts.Have the tightening torque of thewheel nuts and the tyre pressurechecked as soon as possible.
CAUTIONDo not install alloy wheels usingwheel nuts designed for use with steelwheels.
Note: The wheel nuts of alloy wheels andspoked steel wheels can also be used forthe steel spare wheel for a short time(maximum two weeks).1. Install the wheel.2. Install the wheel nuts finger tight.3. Install the locking wheel nut key.
E79156
1
2
65
4
3
4. Partially tighten the wheel nuts in thesequence shown.
5. Lower the vehicle and remove the jack.6. Fully tighten the wheel nuts in the
sequence shown. See TechnicalSpecifications (page 161).
7. Make sure that the projection of thecap is positioned on the same positionas the projection of the hub.
WARNINGHave the wheel nuts checked fortightness and the tyre pressurechecked as soon as possible.
Note: If the spare wheel is different in sizeor construction to the road wheels, have thisreplaced as soon as possible.
159
Wheels and Tyres
Stowing the wheelCAUTION
Do not raise the spare wheel carrierwithout the wheel attached. Damagecan occur to the winch mechanism if
lowered without a wheel attached.
1. Place the wheel flat on the ground, sothe outside of the wheel faces down.Tilt the bracket, and pass it and thecable through the centre opening in thewheel.
2. Fully insert the flat end of the wheelbrace into the guide hole and turnclockwise.
3. Stow the wheel brace, jack, and jackhandle away.
TYRE CAREAlloy Wheels
E136542
Steel Wheels
E136543
To make sure the front and rear tyres ofyour vehicle wear evenly and last longer,we recommend that you swap the tyresas per the graphic at regular intervals of 10000 km (6 000 miles).
CAUTIONDo not scrub the sidewalls of the tyreswhen you are parking.
If you have to mount a kerb, do so slowlyand approach it with the wheels atright-angles to the kerb.Examine the tyres regularly for cuts, foreignobjects and uneven wear of the tread.Uneven wear could mean that the wheelalignment is outside specification.
USING WINTER TYRES
CAUTIONMake sure that you use the correctwheel nuts for the type of wheel thewinter tyres are fitted to.
If winter tyres are used, make sure that thetyre pressures are correct. See TechnicalSpecifications (page 161).
160
Wheels and Tyres
USING SNOW CHAINS
WARNINGSDo not exceed 50 km/h (30 mph).
Do not use snow chains on snow-freeroads.
CAUTIONIf your vehicle is fitted with wheeltrims, remove them before fittingsnow chains.
Note: The ABS will continue to operatenormally.Note: Tighten the snow chains after 1 km(0.5 miles).Only use small link snow chains.Only use snow chains on the rear wheels.On 4-wheel drive vehicles, inflate the reartyres to the maximum pressurepermissible. See TechnicalSpecifications (page 161).
TECHNICAL SPECIFICATIONSWheel nut torque
Nm (Ib-ft)Wheel type
87.5 - 118.5 (65 - 87)All
Tyre pressures (cold tyres)
Full loadEconomyNormal load
Tyre sizeVariant RearFrontRearFrontRearFront
bar (psi)bar (psi)bar (psi)bar (psi)bar (psi)bar (psi)
3.8 (54)2.6 (38)2.6 (38)2.6 (38)2.4 (35)2.4 (35)215/70 R
16*4x2
3.0 (44)2.6 (38)2.6 (38)2.6 (38)2.4 (35)2.4 (35)255/70 R
16*All
3.0 (44)2.6 (38)2.6 (38)2.6 (38)2.4 (35)2.4 (35)265/65 R
17*All
3.0 (44)2.6 (38)2.6 (38)2.6 (38)2.4 (35)2.4 (35)265/60
R 18*All
*Only fit snow chains to specified tyres.
161
Wheels and Tyres
VEHICLE IDENTIFICATIONPLATE
E85610C
B
E D
A
Vehicle identification numberAGross vehicle weightBGross train weightCMaximum front axle weightDMaximum rear axle weightE
The vehicle identification number andmaximum weights are shown on a platelocated on the bottom of the passengerdoor aperture.
VEHICLE IDENTIFICATIONNUMBERDepending on the build location of yourvehicle, the stamped vehicle identificationnumber can be found in the followinglocations.
A
B
E133363
Left-hand side of the instrumentpanel.
A
Right-hand side beneath thefront door on the chassis.
B
162
Vehicle identification
Dimension in mm(inches)
Dimension DescriptionItem
5274 (207.6)Maximum length - excluding rear bumperA
5351 (210.7)Maximum length - including rear bumperA
1850 (72.8)Overall width - excluding exterior mirrorsB
1703 (67.0)Overall height (4x2)C
1800 (70.9)Overall height (4x2* or 4x4)C
3220 (126.8)WheelbaseD
1590 (62.6)Track - front and rear (4x2)E
1560 (61.4)Track - front and rear (4x4)E*Vehicles with increased ride height
4-door stretch cab
E131994
164
Capacities and Specifications
E131996
Dimension in mm(inches)
Dimension DescriptionItem
5274 (207.6)Maximum length - excluding rear bumperA
5351 (210.7)Maximum length - including rear bumperA
1850 (72.8)Overall width - excluding exterior mirrorsB
1706 (67.2)Overall height (4x2)C
1804-1810 (71.0 - 71.2)1Overall height (4x2* or 4x4)C
3220 (126.8)WheelbaseD
1590 (62.6)Track - front and rear (4x2)E
1560 (61.4)Track - front and rear (4x4)E1Depending on tyre size*Vehicles with increased ride height
165
Capacities and Specifications
Dimension in mm(inches)
Dimension DescriptionItem
5274 (207.6)Maximum length - excluding rear bumperA
5351 (210.7)Maximum length - including rear bumperA
1850 (72.8)Overall width - excluding exterior mirrorsB
1716 (67.5)Overall height (4x2)C
1815-1821 (71.4 - 71.7)1Overall height (4x2* or 4x4)C
3220 (126.8)WheelbaseD
1590 (62.6)Track - front and rear (4x2)E
1560 (61.4)Track - front and rear (4x4)E1 Depending on tyre size*Vehicles with increased ride height
167
Capacities and Specifications
4x2 (vehicles with increased ride height) and 4x4
D
A
E
GF
B
C
JH
E139245
Dimension in mm(inches)
Dimension DescriptionItem
124 ± 5 (4.8 ± 0.2)Attachment point - centre of tow ball (4x2)A
221.5 ± 5 (8.7 ± 0.2)Attachment point - centre of tow ball (4x2* or 4x4)A
169
Capacities and Specifications
Dimension in mm(inches)
Dimension DescriptionItem
588 (23.1)Centre of tow ball - side memberB
1176 (46.3)Outside of side memberC
419 ± 5 (16.5 ± 0.2)Centre of tow ball - centre of 1st attachment point(4x2)
D
363 ± 5 (14.3 ± 0.2)Centre of tow ball - centre of 1st attachment point(4x2* or 4x4)
D
442 ± 5 (17.4 ± 0.2)Centre of tow ball - centre of 2nd attachment point(4x2)
E
386 ± 5 (15.2 ± 0.2)Centre of tow ball - centre of 2nd attachment point(4x2* or 4x4)
E
542 ± 5 (21.3 ± 0.2)Centre of tow ball - centre of 3rd attachment point(4x2)
F
486 ± 5 (19.1 ± 0.2)Centre of tow ball - centre of 3rd attachment point(4x2* or 4x4)
F
785 ± 5 (30.9 ± 0.2)Center of tow ball - centre of 4th attachment point(4x2)
G
728 ± 5 (28.7 ± 0.2)Center of tow ball - centre of 4th attachment point(4x2* or 4x4)
G
429 ± 5 (16.8 ± 0.2)Center of tow ball - centre of 5th attachment point(4x2)
H
373 ± 5 (14.7 ± 0.2)Center of tow ball - centre of 5th attachment point(4x2* or 4x4)
H
504 ± 5 (19.8 ± 0.2)Center of tow ball - centre of 6th attachment point(4x2)
J
448 ± 5 (17.6 ± 0.2)Center of tow ball - centre of 6th attachment point(4x2* or 4x4)
J
*Vehicles with increased ride height
170
Capacities and Specifications
GENERAL INFORMATIONPress the relevant button on the unit bezelto access the system functions. This willtake you into the selected mode.
One hour modeTo conserve battery power, the system canbe operated in one hour mode. If theignition is off, press the ON/OFF button toswitch the system on. The system willautomatically switch off after one hour.
System notesWARNINGS
The front glass on the liquid crystaldisplay may break if hit with a hardobject. If the glass breaks, do not
touch the liquid crystalline material. In caseof contact with the skin, wash immediatelywith soap and water.
The unit is a highgrade laser productwhich uses an invisible laser beam.If this is handled incorrectly it can
emit dangerous rays. Do not attempt tolook through any openings in the unit.
CAUTIONSIrregular shaped CDs and CDs with ascratch protection film or selfadhesive labels attached should not
be used. Warranty claims, where this typeof disc is found to be inside an audio unitreturned for repair, will not be accepted.
Do not clean the unit with solvents oraerosol cleaning agents. Use only adamp cloth.Do not insert foreign objects into anyof the unit disc drives or media cardslots.Do not insert more than one disc intothe unit disc drive.
CAUTIONSUse only 12 cm (4.7 inches) discs or 8cm (3.1 inches) discs with a suitableadaptor.Do not attempt to open the unit. If theunit malfunctions consult your dealer.Improper use of settings andconnections, other than thoseexplained in this handbook, can
damage the unit.Do not turn the ignition key or attemptto start the engine while the softwareis updating.
The system is recommended for use whenthe ignition key is turned to the accessoryposition or when the engine is running. Ifthe system is used extensively when theengine is not running, care needs to betaken to avoid draining the battery.
ROAD SAFETY
WARNINGSThe system provides you withinformation designed to help youreach your destination quickly and
safely.For reasons of safety, the drivershould only program the systemwhen the vehicle is stationary.The system provides no assistancewith respect to stop signs, trafficlights, areas under construction or
other important safety information.Do not use the system until you havefamiliarised yourself with itsoperation.Only view the system display whendriving conditions permit.
171
Navigation introduction
Safety informationRead and follow all stated safetyprecautions. Failure to do so may increaseyour risk of collision and personal injury.Ford Motor Company shall not be liablefor any damages of any type arising fromfailure to follow these guidelines.If detailed viewing of route instructions isnecessary, pull off the road when it is safeto do so and park your vehicle.Do not use the navigation system to locateemergency services.To use the system as effectively and safelyas possible, always use the latestnavigation information. Your dealer will beable to assist with this.
172
Navigation introduction
Vehicles with SD navigationsystemThe system has a large range of features,yet is easy and intuitive to use. Routeguidance is shown on the display screen.The screen provides full information foroperating the system through the use ofmenus, text screens and map displays.Screen selections are made by scrollingthrough the menus using the up, down, leftand right arrow buttons and pressing theOK button to activate the desired setting.
Basic operation1. Press either the NAV or MENU button
to enter the menu structure.2. Use the up, down, left and right arrow
buttons and scroll through the variousselection lists.
3. Press the OK button to activate yourselection.
Selection listsVarious screens are presented which offera selection list of available options.1. Select the option you require, or if it is
not shown on the screen use the upand down arrow buttons to view theremainder of the selection list.
2. Press the OK button to confirm yourselection.
Alphanumeric keypad entryWhen it is necessary to enter an address,a keypad will appear prompting you toenter a postcode, city, or street.1. Use the up, down, left and right arrow
buttons to select the letter or numberthat you require.
Note: As you spell the entry the results willappear in the display.
Note: The system will limit your entries toonly those characters which spell a validentry.2. Press the OK button to activate your
selection.
Route setting exampleNavigation main screen• To select the navigation system, press
the NAV button. The road safetycaution will be displayed. To use thesystem, read the caution and press theOK button.
Destination input screen• Use the up and down arrow buttons
and scroll to Destination input.• Press the OK button to activate your
selection.Note: A list with several options is shown.• Starting from the top, select the
country followed by either thepostcode if available or city and streetname.
• Use the alphanumeric keypad andselection lists to select your addressdetails.
• Once sufficient information has beenentered, scroll to Start guidance andpress the OK button to activate yourselection.
Note: If you only need to navigate to a citycentre for example, full address details arenot required.• The route is now calculated and the
screen returns to the main navigationscreen with instructions on how toproceed.
• Follow the screen information andvoice prompts to reach yourdestination.
173
Navigation Quick start
E104157 A
1 2 3 4
Descriptions for function buttons1-4
A
Function buttons 1 to 4 are contextdependent, and change according to thecurrent unit mode. Descriptions for thefunctions are shown at the bottom of thescreen display.
174
Navigation unit overview
Vehicles with SD navigation system
1
+0
2
4 5 6
7 8 9
3
A C D E F G
I
N MOPQRS
T
U
V
WX H
B
L
JK
E135352
Function 1.AFunction 2.BSeek down. CD track selection.See Station tuning control(page 195). See Track selection(page 200).
C
On/off and volume control.D
Seek up. CD track selection. SeeStation tuning control (page195). See Track selection (page200).
E
Function 3.FFunction 4.GOK.H
175
Navigation unit overview
Telephone keypad, stationpresets and navigation keypad.See Using the telephone (page210). See Station presetbuttons (page 196). SeeNavigation Quick start (page173).
I
Clock.JTraffic announcement. SeeTraffic information control(page 196).
K
Navigation arrows.LMap.MInformation.NDoor lock indicator.OHazard warning flasher switch.See Hazard Warning Flashers(page 44).
P
Door lock button. See Lockingand Unlocking (page 29).
Q
Navigation.RMenu select.SPhone menu. See Telephone(page 208).
T
Auxiliary, USB and iPod select.See Auxiliary input (AUX IN)socket (page 82). SeeAuxiliary input (AUX IN)socket (page 205). SeeConnectivity (page 229).
U
Radio and waveband select. SeeAudio unit operation (page195).
V
CD eject. See Compact discplayer (page 200).
W
CD select. See Compact discplayer (page 200).
X
LOADING THE NAVIGATIONDATALoading the navigation data
E136622
1. Load the navigation SD card into theaperture.
2. Press the NAV button. The road safetywarning will be shown in the display.
3. Use the up and down arrow buttons toselect the required feature.
4. Press the OK button to confirm yourselection.
For map updates and system upgradesplease refer to your dealer.
176
Navigation unit overview
Most of the important settings for yournavigation unit can be accessed via theMENU or NAV button. The followingsection describes the various options andhow to use them.For menu structures: See InformationDisplays (page 62).
Menu structure - Information andentertainment display - Vehicleswith navigation systemRouteThis feature allows you to customise theroute to your specific journey requirements(for example continue route guidance,block specific sections of your route orselect specific sections of a route).
Destination inputThis feature allows you to enter yourdestination details (for example enter citynames, enter street names or pick a placefrom a map).
TrafficThis feature allows you to customise howyou receive traffic information (forexample review and sort traffic messages,review your route or block parts of yourroute).
Home addressThis feature allows you to start the routeguidance to your home address or changethe details of your home address.
Last destinationsThis feature allows quick access to ahistory of previous destinations entered inthe system. A detailed display will showthe complete stored information includingan overview map. Select the requiredrepeat destination from the list.
FavouritesThis feature allows you to customize apersonal destination address book andassign user defined names to addressesand locations. A detailed display will showthe complete stored information includingan overview map. Select the requiredrepeat destination from the list.
Points of interestThis feature allows you to customise theroute to your specific journey requirements(for example select a museum on route ora specific point of interest near yourdestination).
Tour planningThis feature allows you to enter a numberof different destinations and select theorder in which you wish to visit them. Youcan also modify an existing tour or recall aprevious tour. The system willautomatically calculate and display yourchosen journey.
Store positionThis feature allows you to store and nameyour current position.
Route optionsThis feature allows you to customise theroute to your specific journey requirements(for example select the fastest or mosteconomical route or select a route that willavoid tunnels, seasonal roads and tollroads).
Special functionsThis feature allows you to select GPS andsystem information or a demonstration ofthe system functionality.
177
System settings
Map displayThis feature allows you to change the waythe map screen is displayed (for exampleclean 2D and clean 3D view) and tocustomise display information for yourjourney (for example time to arrival andlane guidance).
Assistance optionsThis feature allows you to customisedisplay information for your journey (forexample signs, lanes and speed limits).
Personal dataThis feature allows you to edit and deletepersonal data (for example your homeaddress).
Reset all settingsThis feature allows you to reset thenavigation settings.
Menu structure - Information andentertainment display - AllvehiclesAudio settingsAdaptive volumeThis feature allows you to adjust thevolume level to compensate for engine androad speed noise. You can turn this on andoff. See Automatic volume control(page 198).
SoundThis feature allows you to adjust the soundsettings (for example bass and treble.
Nav audio mixingThis feature allows you to adjust thevolume mix between the navigation voiceoutput and audio source.
DSP settingsThis feature allows you to customisespeaker output relevant to seat positions.See Digital signal processing (DSP)(page 198).
DSP equaliserThis feature allows you to select the musiccategory that most suits your listeningpreference. The audio output will changeto enhance the particular style of musicchosen. See Digital signal processing(DSP) (page 198).
NewsThis feature allows you to receive newsbulletins from stations on the FMwaveband or radio data system (RDS) andenhanced other network (EON) linkedstations, in the same way as trafficinformation is provided. You can turn thison and off. See News broadcasts (page198).
Alternative frequenciesThis feature will search for and switch tothe strongest station signal when movingfrom one transmission area to another.See Alternative frequencies (page 198).
RDS regionalThis feature controls the behaviour of AFswitching between regionally relatednetworks of a parent broadcaster. SeeRegional mode (REG) (page 199).
BluetoothThis feature allows you to switchBluetooth on or off.
Clock settingsSet timeThis feature allows you to manually adjustthe time.
178
System settings
Set dateThis feature allows you to manually adjustthe date, month and year.
GPS timeThis feature allows you to, if in a suitablecoverage area, automatically adjust thedate and time using GPS.
Set time zoneThis feature allows you select a specifictime zone.
SummertimeThis feature allows you set the system toadjust for seasonal time differences.Note: GPS time must be selected.
24-hour modeThis feature allows you to adjust thesystem between 12 and 24-hour mode.
179
System settings
ROUTE OPTIONS MENUYou can set a number of options whichalter the way a route is planned.Using the up, down, left and right arrowbuttons, you can select from the list whichroad features are to be avoided or includedin the route by turning the feature on or off.
RouteEcoThis option will prioritise the mosteconomical route to the destination.
FastThis option will prioritise the fastest routeto the destination.
ShortThis option will prioritise the shortest routeto the destination..
Always askUse this feature to make sure that you arealways given the choice of route typeselection for your journey.
DriverLeisurelyThis option will prioritise the route for aleisurely driver to the destination.
NormalThis option will prioritise the route for anormal driver to the destination.
FastThis option will prioritise the route for afast driver to the destination.
Eco settingsTrailerUse this feature to change the economysettings of your journey relating to whetheror not you are towing a trailer and if so thesize of trailer being towed.
Roof boxUse this feature to change the economysettings of your journey relating to the useof a roof box.
DynamicWhen switched on, and if the unit isreceiving a valid traffic message channel(TMC) signal, the route will beautomatically updated to take intoaccount real time traffic incidents orcongestion.Note: This feature can be useful in avoidingdelays or hold ups on journeys.
MotorwayWhen switched on the system will look formotorways on your route andautomatically update your route distanceand timings.Note: This feature can be useful in avoidingdelays or hold ups on journeys.
Ferry/motorailWhen switched on the system will look forferry crossings and motorail facilities onyour route and automatically update yourroute distance and timings.
TollWhen switched on the system will look fortoll roads on your route and automaticallyupdate your route distance and timings.
180
Navigation system
Seasonal roadsWhen switched on the system will look forseasonal roads on your route andautomatically update your route distanceand timings.Note: This feature can be useful in avoidingdelays or hold ups on journeys.
Toll stickerWhen switched on the system willautomatically select toll roads and updateyour route distance and timings.
ROUTE DISPLAYSMap displayPress the MAP button for a map view.This view will show your current locationwith your vehicle in the centre shown asan arrow surrounded by a circle. The arrowwill face in the direction of travel.The information on the top line gives thename of the current road, or the next roadto take if a turn is approaching.You can change the way the map isdisplayed by altering the zoom andorientation settings. Press the relevantfunction buttons to change the map scaleand using the left and right arrow buttonszoom in or out. The current map scale isshown on the display.Map scale settings may be set between50 metres to 500 kilometres or 0.05 milesto 500 miles, with an auto setting to thefar left. The auto setting continuouslychanges the map scale according to theroad type being driven.
Junction zoomThis feature will automatically increasethe zoom on the map display at timeswhen you are required to make a turn, orperform more complex manoeuvres.Shortly after the zoom scale will return tothe previous level.Select AUTO to activate junction zoom.
Navigation displayAfter commencing a navigation route, thedefault screen is the main navigationscreen:Once an active route is underway, guidancewill be given by on-screen information andvoice prompts. Whichever audio sourceyou wish to leave the unit in, basic turn byturn and distance information will remainon the screen in the form of a graphic inset.You do not need to leave the unit on themain navigation screen when you arenavigating a route. Slightly more detailedinformation on your route may be availablevia the main navigation screen if required.
WARNINGDo not rely on the screen promptswhen navigating. Always listen to thenavigation voice and take care not
be distracted from the road ahead.
181
Navigation system
PRINCIPLE OF OPERATIONTraffic message channel (TMC) stationsare broadcast on the FM waveband. TMCis a feature that receives traffic alertswhich can be used to plan alternativeroutes and avoid hold ups.
USING TMCPress the TA or TRAFFIC button to showthe traffic menu page.
Traffic announcementTraffic announcement (TA) can be turnedon or off via this menu. If switched on a TAindicator is shown in the informationborder of the status bar.Stations which broadcast on the FMwaveband and carry traffic programme(TP) information are identified by TPshown in the screen display. With TAswitched on the unit will respond to theseannouncements and interrupt musicplayback. After the announcement hasended music playback will resume.
Ending traffic announcementsThe unit will return to normal operation atthe end of each traffic announcement. Toend the announcement prematurely, pressthe TA, TRAFFIC, RADIO or CD buttonduring the announcement.
Using TMC messagesSelect the required item to display a list ofTMC messages. See GeneralInformation (page 62). This is only anoverview display which gives very basicinformation. Select the message yourequire further information on and anotherscreen will be displayed giving full messagedetails on incident location etc.
You may either select a view which showsmessages only affecting your programmedroute, or a view which shows all messagesreceived. Press function button 1 to changethe view.
182
Traffic Message Channel
The road network is constantly changingdue to new roads, changes in roadclassification, etc. Therefore, it is notalways possible to exactly match the mapdata in the system to the current roadnetwork.Map information is regularly updated, butall areas are not necessarily covered to thesame level of detail. Some roads, inparticular private roads, may not beincluded on the database. To help withaccuracy, always use the latest versionnavigation disc. Your dealer will be able toprovide this.
183
Map updates
IMPORTANT AUDIOINFORMATION
WARNINGSDue to technical incompatibility,recordable (CD-R) and rewritable(CD-RW) discs may not function
correctly.These CD radio units will playcompact discs that conform to theInternational Red Book standard
audio specification. Copy protected CDsfrom some manufacturers do not conformto this standard and playback cannot beguaranteed.
Dual format, dual sided discs (DVDPlus, CD-DVD format), adopted bythe music industry, are thicker than
normal CDs and consequently playbackcannot be guaranteed, and jamming couldoccur. Irregular shaped CDs and CDs witha scratch protection film or self adhesivelabels attached should not be used.Warranty claims, where this type of disc isfound to be inside an audio unit returnedfor repair, will not be accepted.
All CD units are designed to playcommercially pressed 12 cm audiocompact discs only.The audio unit may be damaged ifunsuitable items like credit cards orcoins are pushed inside the CD
aperture.
Audio unit labels
E66256
E66257
Disc labelsAudio CD
E66254
MP3
E66255
184
Audio introduction
Note: Units have an integrated multifunction display situated above the CDaperture. This shows important informationregarding control of your audio unit.Additionally, there are various icons placedaround the display screen which light upwhen a function is active (for example CD,Radio or Aux.)Type of audio unit and relevant multifunction display:Type 1: Base audioType 2: Base displayType 3: Large displayType 4: 4.2 inch colour displayType 5: 5 inch NAV colour displayType 1
A B C
NOPQ
D FE G
M K J I HLE136953
CD eject. See Compact discplayer (page 200).
A
Volume/menu control.BCD Aperture.CLCD display.DSeek down. CD trackselect/Fast-rewind. SeeStation tuning control (page195). See Track selection (page200).
E
Display time/date and RDSinformation.
F
On/off and mute.GSeek up. CD trackselect/Fast-forward. SeeStation tuning control (page195). See Track selection (page200).
H
Radio and waveband select. SeeAudio unit operation (page195).
I
Scan and auto store.JStation preset 6. Shuffle. SeeStation preset buttons (page196).
K
Station preset 5. Repeat. SeeStation preset buttons (page196).
L
Station preset 4. Next folder.See Station preset buttons(page 196).
M
Station preset 3. Previous folder.See Station preset buttons(page 196).
N
Station preset 2. Scroll display.See Station preset buttons(page 196).
O
Station preset 1. Menu back. SeeStation preset buttons (page196).
P
Select CD/Auxiliary. SeeCompact disc player (page200). See Auxiliary input (AUXIN) socket (page 82). SeeAuxiliary input (AUX IN)socket (page 205).
Q
185
Audio unit overview
Type 2
1 2
3
5
4
6
A B C D E F
G
H
K JLMN
O
P
Q
I
E135350
CD eject. See Compact discplayer (page 200).
A
CD select. See Compact discplayer (page 200).
B
Seek down. CD track selection.See Station tuning control(page 195). See Track selection(page 200).
C
On/off and volume control.DSeek up. CD track selection. SeeStation tuning control (page195). See Track selection (page200).
E
Station presets. See Stationpreset buttons (page 196).
F
Menu select.G
186
Audio unit overview
Information.HNavigation arrows.ITraffic announcement. SeeTraffic information control(page 196).
J
Door lock indicator.KHazard warning flasher switch.See Hazard Warning Flashers(page 44).
L
Door lock button. See Lockingand Unlocking (page 29).
M
Menu entry/exit.NSound button. See Soundbutton (page 195).
O
Auxiliary select. See Auxiliaryinput (AUX IN) socket (page82). See Auxiliary input (AUXIN) socket (page 205).
P
Radio and waveband select. SeeAudio unit operation (page195).
Q
Type 3 and Type 4
E104157 A
1 2 3 4
Descriptions for function buttons1-4
A
187
Audio unit overview
1
+0
2
4 5
7 8 9
3
A C D E F G
I
L KMNOPQ
R
S
T
UV H
B
J
E135351
Function 1.AFunction 2.BSeek down. CD track selection.See Station tuning control(page 195). See Track selection(page 200).
C
On/off and volume control.D
Seek up. CD track selection. SeeStation tuning control (page195). See Track selection (page200).
E
Function 3.FFunction 4.GMenu select.H
188
Audio unit overview
Telephone keypad and stationpresets. See Using thetelephone (page 210). SeeStation preset buttons (page196).
I
Navigation arrows.JTraffic announcement. SeeTraffic information control(page 196).
K
Information.LDoor lock indicator.MHazard warning flasher switch.See Hazard Warning Flashers(page 44).
N
Door lock button. See Lockingand Unlocking (page 29).
O
Sound button. See Soundbutton (page 195).
P
Menu entry/exit.QPhone menu. See Telephone(page 208).
R
Auxiliary, USB and iPod select.See Auxiliary input (AUX IN)socket (page 82). SeeAuxiliary input (AUX IN)socket (page 205). SeeConnectivity (page 229).
S
Radio and waveband select. SeeAudio unit operation (page195).
T
CD eject. See Compact discplayer (page 200).
U
CD select. See Compact discplayer (page 200).
V
Function buttons 1 to 4 are contextdependent, and change according to thecurrent unit mode. Descriptions for thefunctions are shown at the bottom of thescreen display.Type 5
E104157 A
1 2 3 4
Descriptions for function buttons1-4
A
189
Audio unit overview
1
+0
2
4 5 6
7 8 9
3
A C D E F G
I
N MOPQRS
T
U
V
WX H
B
L
JK
E135352
Function 1.AFunction 2.BSeek down. CD track selection.See Station tuning control(page 195). See Track selection(page 200).
C
On/off and volume control.D
Seek up. CD track selection. SeeStation tuning control (page195). See Track selection (page200).
E
Function 3.FFunction 4.GMenu select.H
190
Audio unit overview
Telephone keypad, stationpresets and navigation keypad.See Using the telephone (page210). See Station presetbuttons (page 196). SeeNavigation Quick start (page173).
I
Clock.JTraffic announcement. SeeTraffic information control(page 196).
K
Navigation arrows.LMap.MInformation.NDoor lock indicator.OHazard warning flasher switch.See Hazard Warning Flashers(page 44).
P
Door lock button. See Lockingand Unlocking (page 29).
Q
Navigation.RMenu entry/exit.SPhone menu. See Telephone(page 208).
T
Auxiliary, USB and iPod select.See Auxiliary input (AUX IN)socket (page 82). SeeAuxiliary input (AUX IN)socket (page 205). SeeConnectivity (page 229).
U
Radio and waveband select. SeeAudio unit operation (page195).
V
CD eject. See Compact discplayer (page 200).
W
CD select. See Compact discplayer (page 200).
X
Function buttons 1 to 4 are contextdependent, and change according to thecurrent unit mode. Descriptions for thefunctions are shown at the bottom of thescreen display.
191
Audio unit overview
SECURITY CODEEach unit incorporates a unique code thatis needed to activate the audio systemwhen the vehicle battery has beendisconnected and reconnected. The 4 digitcode is included in the owner informationpack.If the security code is not available, pleasesee your dealer.
192
Audio system security
SETTING THE CLOCK ON THEAUDIO UNITChanging the timeThe clock can be set at any time when thesystem is in the one hour mode or theignition switch is in the ACC or ON position.Note: Type 2 and 3: The time can beadjusted using the hour and minute buttonson the screen.To advance the hours, press the HOUR SETbutton. To advance the minutes, press theMINUTE SET button while the time isflashing.Note: Type 5: The time can be adjustedusing the clock button on the audio controlpanel. See Audio unit overview (page 185).Note: The time can be adjusted using thenavigation arrow buttons on the audiocontrol panel.Type 1• Press the MENU button.• Rotate the MENU CONTROL to select
the date/time.• Short press the MENU button to enter
date/time.• Rotate the MENU CONTROL to select
the hour set and enter.• Rotate the MENU CONTROL to adjust
the hours.• Press BACK button to return to
previous menu.• Rotate the MENU CONTROL to select
minute set and enter.• Rotate the MENU CONTROL to adjust
minutes.• Press MENU button to save the new
settings.
Type 2, 4 and 5• Press the MENU button.• Use the UP and DOWN arrow buttons
to select the clock settings.• Press OK or RIGHT arrow button to
enter clock settings.• Use UP and DOWN arrow button to
select the set time.• Use UP and DOWN arrow buttons to
adjust hours.• Use RIGHT and LEFT arrow buttons to
scroll to the minutes.• Use UP and DOWN arrow buttons to
adjust minutes.• Press OK button to save the new
settingsType 3• Press the MENU button.• Use the UP and DOWN arrow buttons
to select the clock.• Press OK or RIGHT arrow button to
enter clock menu.• Use UP and DOWN arrow button to
select the set time.• Use UP and DOWN arrow buttons to
adjust hours.• Use RIGHT and LEFT arrow buttons to
scroll to the minutes.• Use UP and DOWN arrow buttons to
adjust minutes.• Press OK button to save the new
settings
Exact hour adjustmentYou can set the time to the beginning ofan hour using this feature.• Press the CLOCK button for about two
seconds until a beep is heard. Theclock's current time will flash.
• Press the CLOCK button again and thetime will be adjusted as follows:
193
Audio unit clock and date displays
Example• current set time between 12:01 and
12:29 will change to 12:00 exactly• current set time between 12:30 and
12:59 will change to 1:00 exactly.
Note: If the power supply to the unit isinterrupted (if the fuse blows or the vehicle'sbattery is disconnected), the clock will needto be reset.
194
Audio unit clock and date displays
ON/OFF CONTROLPress the on/off control. This will alsooperate the unit for up to one hour with theignition turned off.The radio will switch off automaticallyafter one hour.
SOUND BUTTONThis will allow you to adjust the soundsettings (for example bass and treble).1. Press the sound button.2. Use the up and down arrow buttons to
select the required setting.3. Use the left and right arrow buttons to
make the necessary adjustment. Thedisplay indicates the level selected.
4. Press the OK button to confirm thenew settings.
WAVEBAND BUTTONPress the RADIO button to select from thewavebands available.The selector can also be used to return toradio reception when you have beenlistening to another source.Alternatively, press the left arrow buttonto display the available wavebands. Scrollto the required waveband and press OK.
STATION TUNING CONTROLSeek tuningSelect a waveband and briefly press oneof the seek buttons. The unit will stop atthe first station it finds in the direction youhave chosen.
Manual tuningType 11. Press the FM/AM button and then
MANUAL TUNE.2. Use the left and right arrow buttons to
tune down or up the waveband in smallincrements or press and hold toincrement quickly, until you find astation you want to listen to.
Type 21. Press the MENU button.2. Select RADIO mode and then MANUAL
TUNE.3. Use the left and right arrow buttons to
tune down or up the waveband in smallincrements or press and hold toincrement quickly, until you find astation you want to listen to.
4. Press OK to continue listening to astation.
Type 3, 4 and 51. Press function button 2.2. Use the left and right arrow buttons to
tune down or up the waveband in smallincrements or press and hold toincrement quickly, until you find astation you want to listen to.
3. Press OK to continue listening to astation.
Scan tuningScan allows you to listen to 8 seconds ofeach station detected.
Type 11. Press the FM/AM button.2. Short press the SCAN/AS button, the
radio will automatically scan up theselected waveband.
195
Audio unit operation
3. Short press the SCAN/AS button againto continue listening to a station.
Type 21. Press the MENU button.2. Select RADIO mode and then SCAN.3. Use the seek buttons to scan up or
down the selected waveband.4. Press OK to continue listening to a
station.
Type 3, 4 and 51. Press function button 3.2. Use the seek buttons to scan up or
down the selected waveband.3. Press function button 3 again or OK to
continue listening to a station.
STATION PRESET BUTTONSThis feature allows you to store yourfavourite stations so that they can berecalled by selecting the appropriatewaveband and pressing one of the presetbuttons.1. Select a waveband.2. Tune to the station required.3. Press and hold one of the preset
buttons. A progress bar and messagewill appear. When the progress barcompletes the station has been stored.The audio unit will also mutemomentarily as confirmation.
This can be repeated on each wavebandand for each preset button.Note: When you drive to another part of thecountry, FM stations that broadcast onalternative frequencies, and are stored onpreset buttons, may be updated with thecorrect frequency and station name for thatarea.
AUTOSTORE CONTROLNote: This will store the strongest signalsavailable, either from the AM or the FMwaveband, and overwrite the previouslystored stations. It can also be used to storestations manually in the same way as otherwavebands.
Type 11. In RADIO mode, long press the
SCAN/AS button.2. When the search is complete, sound is
restored and the strongest 6 stationsare stored on the Autostore presets.
Type 2, 3, 4 and 51. Press and hold function button 1 or the
RADIO button.2. When the search is complete, sound is
restored and the strongest 10 stationsare stored on the Autostore presets.
TRAFFIC INFORMATIONCONTROLMany stations that broadcast on the FMwaveband have a TP code to signify thatthey carry traffic programme information.
Activating traffic announcementsBefore you can receive trafficannouncements, you must press either theTA or TRAFFIC button. A ‘TA’ display willappear to show the feature is switched on.If you are already tuned to a station thatbroadcasts traffic information, ‘TP’ willalso be displayed. Otherwise the unit willsearch for a traffic programme.When traffic information is broadcast, itwill automatically interrupt normal radioor CD playback and ‘Traffic announcement(TA)’ will appear in the display.
196
Audio unit operation
If a non-traffic station is selected orrecalled using a preset button, the audiounit will remain on that station unless TAor TRAFFIC is turned off, then on again.Note: If TA is on and you select a preset ormanual tune to a non TA station no trafficannouncement will be heard.Note: When you are listening to a non TAstation and turn TA off and on again a TPseek will occur.
Traffic announcement volumeTraffic announcements interrupt normalbroadcasts at a preset minimum level thatis usually louder than normal listeningvolumes.To adjust the preset volume:• Use the volume control to make the
necessary adjustment during anincoming TA broadcast. The displaywill show the level selected.
Ending traffic announcementsThe audio unit will return to normaloperation at the end of each trafficannouncement. To end the announcementprematurely, press TA or TRAFFIC duringthe announcement.Note: If you press TA or TRAFFIC at anyother time it will switch all announcementsoff.
197
Audio unit operation
AUTOMATIC VOLUMECONTROLWhen available, automatic volume control(AVC) adjusts the volume level tocompensate for engine noise and roadspeed noise.1. Press the MENU button and select
AUDIO.2. Select AVC LEVEL or ADAPTIVE VOL.3. Use the left or right arrow button to
adjust the setting.4. Press the OK button to confirm your
selection.5. Press the MENU button to return.
DIGITAL SIGNAL PROCESSING(DSP)DSP occupancyThis feature takes into account thedifferences in distance from the variousspeakers in the vehicle to each seat. Selectthe sitting position for which the audio isto be correctly enhanced.
DSP equaliserSelect the music category that most suitsyour listening preference. The audio outputwill change to enhance the particular styleof music chosen.
Changing the DSP settings1. Press the MENU button.2. Select AUDIO or AUDIO SETTINGS.3. Scroll to the required DSP function.4. Use the up and down arrow buttons to
select the required setting.5. Press the OK button to confirm your
selection.6. Press the MENU button to return.
NEWS BROADCASTSSome audio units interrupt normalreception to broadcast news bulletins fromstations on the FM waveband or radio datasystem (RDS) and enhanced othernetwork (EON) linked stations, in the sameway as traffic information is provided.During news broadcasts, the display willindicate there is an incomingannouncement. News interrupts arebroadcast at the same preset volume levelas traffic announcements.1. Press the MENU button.2. Select AUDIO or AUDIO SETTINGS.3. Scroll to NEWS and turn on or off with
the OK button.4. Press the MENU button to return.
ALTERNATIVE FREQUENCIESMany programmes that broadcast on theFM waveband have a programmeidentification (PI) code, which can berecognised by audio units.If your radio has alternative frequencies(AF) tuning switched on and you movefrom one transmission area to another, thisfacility will search for and switch to astronger station signal, if one can be found.Under certain conditions, however, AFtuning may temporarily disrupt normalreception.When selected, the unit continuallyevaluates signal strength and, if a bettersignal becomes available, the unit willswitch to that alternative. It mutes whileit checks a list of alternative frequenciesand, if necessary, it will search once acrossthe selected waveband for a genuinealternative frequency.
198
Audio unit menus
It will restore radio reception when it findsone or, if one is not found, the unit willreturn to the original stored frequency.When selected, ‘AF’ will be shown in thedisplay.1. Press the MENU button.2. Select AUDIO or AUDIO MENU.3. Scroll to ALTERNAT FREQ. or
ALTERNATIVE FREQ. and turn on or offwith the OK button.
4. Press the MENU button to return.
REGIONAL MODE (REG)Regional mode (REG) controls thebehaviour of AF switching betweenregionally related networks of a parentbroadcaster. A broadcaster may run a fairlylarge network across a large part of thecountry. At various times of the day thislarge network may be broken down into anumber of smaller regional networks,typically centred on major towns or cities.When the network is not split into regionalvariants, the whole network caries thesame programming.Regional mode ON: This prevents 'random'AF switches when neighbouring regionalnetworks are not carrying the sameprogramming.Regional mode OFF: This allows a largercoverage area if neighbouring regionalnetworks are carrying the sameprogramming, but can cause 'random' AFswitches if they are not.1. Press the MENU button.2. Select AUDIO or AUDIO SETTINGS.3. Scroll to RDS REGIONAL and turn on
or off with the OK button.4. Press the MENU button to return.
199
Audio unit menus
COMPACT DISC PLAYBACKNote: During playback, the display indicatesthe disc, track and time that has elapsedsince the start of the track.During radio reception, press the CD buttononce to start CD playback.Playback will start immediately after a discis loaded.
TRACK SELECTION• Press the seek up button once to move
to the next track or press it repeatedlyto access later tracks.
• Press the seek down button once toreplay the current track. If pressedwithin two seconds of the start of atrack, the previous track will beselected.
• Press the seek down button repeatedlyto select previous tracks.
Type 2, 3, 4 and 5• Press the up or down arrow buttons,
and using the OK button, select therequired track.
Type 3, 4 and 5The desired track number may be enteredusing the numeric keypad. Dial the requiredtrack number until complete (for example1 then 2 for track 12), or dial the numberand directly press OK.
FAST FORWARD/REVERSEPress and hold the seek down or upbuttons to search backwards or forwardswithin the tracks on the disc.
SHUFFLE/RANDOMRandom track playback, also known asshuffle, plays all tracks on the CD inrandom order.
Type 11. Press the SHUFFLE button in CD mode.When an MP3 CD is playing, optionsinclude SHUFFLE for the whole CD, or toplay all the tracks in the folder in a randomorder.
Type 21. Press the MENU button and select CD
MODE.2. Select SHUFFLE, which then enables
the function to be selected on or off.When an MP3 CD is playing, optionsinclude SHUFFLE for the whole CD, or toplay all the tracks in the folder in a randomorder.
Type 3, 4 and 5Press function button 2.Note: When an MP3 CD is playing, optionsinclude SHUFFLE for the whole CD, or toplay all the tracks in the folder in a randomorder. Repeat presses of function button 2will toggle these options.Use the seek up or down button to selectthe next track to shuffle if required.
REPEAT COMPACT DISCTRACKSType 11. Press REPEAT button in CD mode.When an MP3 CD is playing, optionsinclude REPEAT for the track, or to repeatall the tracks in the folder.
200
Compact disc player
Type 21. Press the MENU button and select CD
MODE.2. Select REPEAT, which then enables
the function to be selected on or off.The track will replay once ended.
When an MP3 CD is playing, optionsinclude REPEAT for the track, or to repeatall the tracks in the folder.
Type 3, 4 and 5Press function button 1.When an MP3 CD is playing, optionsinclude REPEAT for the track, or to repeatall the tracks in the folder. Repeat pressesof function button 1 will toggle theseoptions.
COMPACT DISC TRACKSCANNINGThe SCAN function allows you to previeweach track for approximately 8 seconds.
Type 11. Press CD/AUX to select CD MODE.2. Short press SCAN/AS button to
activate CD scanning.3. Short press the SCAN/AS button again
to continue listening to a track.
Type 2Various scan modes are possible,according to the type of CD currentlyplaying.1. Press the MENU button and select CD
MODE.2. Select SCAN, which then enables the
function to be selected on or off.
Note: When an MP3 CD is playing, optionsinclude SCAN for the CD, or just the tracksin the folder.3. Press the OK button to stop the scan
mode.
Type 3, 4 and 51. Press function button 3.Note: When an MP3 CD is playing, optionsinclude SCAN for the CD, or just the tracksin the folder. Repeat presses of functionbutton 3 will toggle these options.2. Press function button 3 again to stop
the scan mode.
MP3 FILE PLAYBACKMP3 (MPEG 1 Audio Layer-3) is a standardtechnology and format for compressingaudio data. This allows a more efficientuse of the media.You can play MP3 files recorded onCD-ROMs, CD-Rs, and CD-RWs. The discmust be in the ISO 9660 level 1 or level 2format, or Joliet or Romeo in the expansionformat. You can also use a disc recordedin Multi Session.
ISO 9660 formatThis is the most common internationalstandard for the logical format of files andfolders on a CD-ROM.There are several specification levels. InLevel 1, file names must be in the 8.3format (no more than 8 characters in thename, no more than 3 characters in theextension “.MP3”) and in capital letters.Folder names can be no longer than 8characters. There can be no more than 8folder levels (trees). Level 2 specificationsallow file names up to 31 characters long.Each folder can have up to 8 trees.
201
Compact disc player
For Joliet or Romeo in the expansionformat, please consider these restrictionswhen configuring your CD writing software.
Multi sessionThis is a recording method that enablesadding of data using the Track-At-Oncemethod.Conventional CDs begin at a CD controlarea called the Lead-in and end at an areacalled Lead-out. A Multi Session CD is aCD having multiple sessions, with eachsegment from Lead-in to Lead-outregarded as a single session.• CD-Extra: The format that records
audio (audio CD data) as tracks onsession 1, and records data as trackson session 2.
• Mixed CD: In this format, data isrecorded as track 1, and audio (audioCD data) is recorded as track 2.
File formats• With formats other than ISO 9660
level 1 and level 2, folder names or filenames may not be displayed correctly.
• When naming, be sure to add the fileextension “.MP3” to the file name.
• If you put the extension “.MP3” to a fileother than MP3, the unit cannotrecognize the file properly and willgenerate random noise that coulddamage your speakers.
• The following discs take a longer timeto start playback.• a disc recorded with complicated
tree structure.• a disc recorded in Multi Session.• a non-finalised disc to which data
can be added.
Playing a multi session discWhen the first track of the first sessionis audio CD dataOnly audio CD data of the first session isplayed back. Non-audio CD data/MP3 fileinformation (track number, time, etc.) isdisplayed with no sound.When the first track of the first sessionis not audio CD data• If an MP3 file is in the disc, only MP3
file(s) play back and other data isskipped. (Audio CD data is notrecognised.)
• If no MP3 file is in the disc, nothing isplayed back. (Audio CD data is notrecognised.)
MP3 files playback orderThe playback order of the folders and filesis as shown.Note: A folder that does not include an MP3file is skipped.Playback tip: To specify a desiredplayback order, before the folder or filename, input the order by number (e.g., “01,”“02”), then record contents onto a disc.(The order differs depending on the writingsoftware.)
202
Compact disc player
E104206
ID3 Tag Version 2The following occurs when an MP3 filecontaining ID3 tag ver.2 is played:• When skipping a portion of ID3 tag ver.2
(at the beginning of the track), soundis not output. Skip time changesdepending ID3 tag ver.2 capacity.Example: At 64 kbytes, it is about 2seconds (with RealJukebox).
• The displayed elapsed playing timewhen skipping a portion of ID3 tag ver.2is inaccurate. For MP3 files of a bit rateother than 128 kbps, time is notdisplayed accurately during playback.
• When an MP3 file is created with MP3conversion software (e.g. RealJukebox- a registered trademark ofRealNetworks Inc), ID3 ver.2 willautomatically be written.
MP3 navigationMP3 tracks may be recorded on the CD inseveral ways. They can all be placed in theroot directory like a conventional audio CD,or they can be placed in folders that mayrepresent, for example, an album, an artist,or a genre.The normal playing sequence on CDs withmultiple folders is to play the tracks withinthe root (top level) first, then the tracks inany folder(s) within the root, then moveonto the second folder, and so forth.• Press the up or down arrow buttons to
enter the track list.• Navigate the hierarchy using the arrow
buttons to select another folder ortrack (file).
• Press OK to select a highlighted track.
MP3 DISPLAY OPTIONSNote: Type 1 units may require repeatedbutton presses of the INFO button to displayall the available track information.When an MP3 disc is playing, certaininformation encoded in each track can bedisplayed. Such information will normallyinclude:• The file name• The folder name• ID3 information which might be the
album or artist’s nameThe unit will normally show the file namethat is playing. To select one of the otheritems of information:• Press the INFO button.
CD text display optionsWhen an audio disc with CD text is playing,limited information encoded in each trackcan be displayed. Such information willnormally include:
203
Compact disc player
• The disc name• The artist name• The track nameThese display options are selected in thesame way as MP3 displays.
ENDING COMPACT DISCPLAYBACKTo restore radio reception on all units:• Press the RADIO button.Note: This will not eject the CD; the discwill merely pause at the point where radioreception was restored.To resume CD playback, press the CDbutton again.
204
Compact disc player
Note: For optimum performance whenusing any auxiliary device set the volume onthe device high. This will reduce audiointerference when charging the device viathe vehicle power supply socket.When fitted the Auxiliary input (AUX IN)socket permits an auxiliary device, such asan MP3 player, to be linked into the vehicleaudio system. Output can be playedthrough the vehicle speakers.To connect an auxiliary device, plug it intothe AUX IN socket using a 3.5 mmconventional audio jack connector.Select the auxiliary input via the AUXbutton and playback will be heard throughthe vehicle speakers. LINE IN or LINE INACTIVE will appear in the vehicle audiounit display. Volume, treble and bass canbe adjusted on the vehicle audio unit asnormal.The vehicle audio unit buttons can also beused to restore playback from the vehicleaudio unit, while the auxiliary deviceremains connected.
205
Auxiliary input (AUX IN) socket
ANTENNAThe radio aerial is mounted on the roof ofthe vehicle above the interior rear viewmirror. It is fixed and cannot be raised andlowered, however the assembly can beremoved by unscrewing from the base.
CAUTIONTo prevent damage to the aerial,remove it before entering a car washor passing beneath a low overhead
clearance.
206
Audio system care
RectificationAudio unit display
General error message for CD fault conditions, such ascannot read the CD, data-CD inserted, etc. Ensure discis loaded correct way up. Clean and re-try, or replace
disc with known music disc. If error persists contact yourdealer.
PLEASE CHECK CD
General error message for CD fault conditions such aspossible mechanism fault.
CD DRIVE MALFUNCTION
Ambient temperature too hot – unit will not work untilit has cooled down.
CD DRIVE HIGH TEMP
General error message for iPod fault conditions, suchas cannot read the data. Ensure iPod is inserted
correctly. If error persists contact your dealer.
IPOD ERROR READING DEVICE
207
Audio troubleshooting
GENERAL INFORMATION
CAUTIONUsing the system with the engine offwill drain the battery.
This section describes the functions andfeatures of the Bluetooth mobile phonehands free system.The Bluetooth mobile phone part of thesystem provides interaction with the audioor navigation system and your mobilephone. It allows you to use the audio ornavigation system to make and receivecalls without having to hold your mobilephone.
Compatibility of phonesCAUTION
As no common agreement exists,mobile phone manufacturers are ableto implement a variety of profiles in
their Bluetooth devices. Because of this,an incompatibility can occur between thephone and hands-free system, which insome cases may significantly degrade thesystem performance. To avoid thissituation, only recommended phonesshould be used.
Please visit the website www.ford-mobile-connectivity.com for full details.
TELEPHONE SETUPPhonebookAfter start up access to the phonebook listcan be delayed for several minutes,depending upon the size.
Phonebook categoriesDepending on your phonebook entry,different categories can be displayed inthe audio unit.For example:
MobileM
OfficeO
HomeH
FaxF
Note: Entries may be displayed without acategory attachment.The category can also be indicated as anicon:
E87990
Phone
E87991
Mobile
E87992
Home
E87993
Office
E87994
Fax
Making a phone an active phoneWhen using the system for the first time,no phone is connected to the system.
Bluetooth phoneAfter bonding a Bluetooth phone to thesystem, this becomes the active phone.For further information refer to the phonemenu.
208
Telephone
Select the phone from the active phonemenu.Turning the ignition and radio or navigationunit back on again, the last active phoneis picked up by the system.Note: In some cases the Bluetoothconnection must also be confirmed on thephone.
Bond another Bluetooth phoneBond a new Bluetooth phone as describedin the requirements for a Bluetoothconnection.Phones stored in the system are accessibleby using the phone list on the audio unit.Note: A maximum of six devices may bebonded. If six Bluetooth devices havealready been bonded, one of these has tobe debonded in order to bond a new device.
BLUETOOTH SETUPBefore you can use your telephone withyour vehicle it must be bonded to thevehicle telephone system.
Handling of phonesUp to six Bluetooth devices can be bondedto the vehicle system.Note: If there is an ongoing call when thephone in use is selected as the new activephone, the call is transferred to the vehicleaudio system.Note: Even if connected to the car system,your phone can still be used in the usualway.
Requirements for BluetoothconnectionThe following are required before aBluetooth phone connection can be made.
1. The Bluetooth feature must beactivated on the phone and on theaudio unit. Make sure the Bluetoothmenu option in the audio unit is set toON. For information on phone settings,refer to your phone user guide.
2. In the Bluetooth menu on your phone,search for Ford Audio and select it.
3. Enter the code number shown on thevehicle display using the phone keypad.If no code number is shown on thedisplay, enter the Bluetooth PINnumber 0000 using the phone keypad.Now enter the Bluetooth PIN numbershown on the vehicle display.
4. If your mobile phone asks you toauthorize the automatic connection,select YES.
Note: A phone call will be disconnected ifthe audio unit is switched off. If the ignitionkey is turned to the off position the phonecall will remain in progress.
209
Telephone
TELEPHONE CONTROLSRemote controlAccept and reject call button
B A
E138709
Reject callAAccept callB
Incoming calls can be accepted by pressingthe answer call button once. Press thereject call button to end the call or to rejectthe incoming call.
USING THE TELEPHONENote: You can exit the phone menu bypressing any source button CD, RADIO orAUX.Note: When referred to, the use of the seekup and seek down buttons can be used oneither the steering wheel or the audio unit.This chapter describes the phone functionsof the audio unit.An active phone must be present.Even if connected to the audio unit, yourphone can still be used in the usual way.
Making a callDialling a number using voice controlPhone numbers can be dialled using voicecontrol. See Telephone commands(page 222).
Dialling a number using the addressbookYou can access your phone address bookvia Bluetooth. The entries will appear inthe unit display.1. Press the PHONE button.2. Press the up/down arrow buttons until
PHONEBOOK is shown.3. Press the OK button.Note: You can also use the telephonekeypad to select the first letter of the entryyou are looking for. Press the relevantnumber that corresponds to the letterrepeatedly until the required letter isdisplayed.4. Press the up/down arrow buttons to
select the desired phone number.Note: Press and hold the up/down arrowbuttons to search forwards or backwardswithin the phonebook.5. Press the OK button to dial the
selected phone number.
Dialling a number using the telephonekeypadIf you have an audio unit with a telephonekeypad (buttons 0-9, * and #):1. Press the PHONE button.2. Press the up/down arrow buttons until
DIAL NUMBER is shown.3. Press the OK button.4. Dial the number using the telephone
keypad on the audio unit.5. Press the OK button.
210
Telephone
Note: If you enter an incorrect digit whilstentering a phone number, press functionbutton 3 to erase the last digit. A long presswill erase the complete string of digits.Press and hold 0 to enter a + digit.
Ending a callCalls can be ended by:• Pressing the reject call button.• Pressing the OK button.• Pressing function button 4.
Redialling a number1. Press the PHONE or the answer call
button.2. Press the up/down arrow buttons until
CALL LISTS is displayed.3. Press the OK button.Note: If the active phone does not providea call out list, the last outgoing callnumber/entry can be redialled.4. Press the up/down buttons to select
the desired call list.5. Press the OK button.6. Press the up/down buttons to select
the desired phone number.7. Press the OK button.
Redialling the last dialled number1. Press the PHONE or the answer call
button.2. Press the up/down arrow buttons until
REDIAL is displayed.3. Press the OK button.
Receiving an incoming callAccepting an incoming callIncoming calls can be accepted by pressingthe answer call button, or by pressing theOK button.
Rejecting an incoming callIncoming calls can be rejected by:• Pressing the reject call button, or• Pressing the arrow down button to
highlight REJECT and then pressingthe OK button.
Receiving a second incoming callNote: The second incoming call functionmust be activated in your phone.If there is an incoming call whilst there isan ongoing call, a beep will be heard andyou will have the option to end the activecall and to accept the incoming call.
Accepting a second incoming callNote: The first incoming call will bedisconnected and replaced by the secondincoming call.Second incoming calls can be acceptedby pressing the answer call button on thesteering wheel, the PHONE button, or bypressing the OK button on the audio unit.
Rejecting a second incoming callSecond incoming calls can be rejected by:• Pressing the reject call button.• Pressing the arrow down button to
highlight REJECT and then pressingthe OK button.
• Pressing function button 4.
Muting the microphoneNote: During a call, it is possible to mutethe microphone. Whilst muted, confirmationwill appear in the display.Press function button 1. Press the buttononce again to turn this function off.
Changing the active phoneNote: Phones must be bonded to thesystem before they can be made active.
211
Telephone
Note: After bonding a phone to the system,this becomes the active phone.1. Press the PHONE button.2. Press the up/down buttons until
SELECT PHONE is shown.3. Press the OK button.4. Scroll through the different stored
phones by using the up/down buttonsto display the bonded phones.
5. Press the OK button to select thephone which is to be the active phone.
Debonding a bonded phoneA bonded phone can be deleted from thesystem at any time, unless a phone call isin progress.1. Press the PHONE button.2. Press the up/down buttons until
SELECT PHONE is shown.3. Press the OK button.4. Press the up/down buttons to highlight
the required phone.5. Press function button 1.
212
Telephone
PRINCIPLE OF OPERATION
CAUTIONUsing the system with the engine offwill drain the battery.
Voice recognition enables operation of thesystem without the need to divert yourattention from the road ahead in order tochange settings, or receive feedback fromthe system.Whenever you issue one of the definedcommands with the system active, thevoice recognition system converts yourcommand into a control signal for thesystem. Your inputs take the form ofdialogues or commands. You are guidedthrough these dialogues byannouncements or questions.Please familiarise yourself with thefunctions of the system before using voicerecognition.
Supported commandsThe voice control system allows you tocontrol the following vehicle functions:• Bluetooth phone• radio• CD Player• external device (USB)• external device (iPod)• external device (Line in)• external device (Bluetooth)• automatic climate control
System responseAs you work through a voice session thesystem will prompt you with a beep toneeach time the system is ready to proceed.
Do not try to give any commands until thebeep tone has been heard. The voicecontrol system will repeat each spokencommand back to you.If you are not sure how to continue say"HELP" for assistance or "CANCEL" if youdo not wish to continue.The "HELP" function provides only asubset of the available voice commands.Detailed explanations of all possible voicecommands can be found on the followingpages.
Voice commandsAll voice commands should be given usinga natural speaking voice, as if speaking toa passenger or on the phone. Your voicelevel should be dependant on thesurrounding noise level inside or outsidethe vehicle but do not shout.
USING VOICE CONTROLSystem operationThe order and content of the voice controlsare given in the following lists. The tablesshow the sequence of user voicecommands and system responses for eachavailable function.<> indicates a number or stored name tagto be inserted by the user.
Short cutsThere are a number of voice commandshort cuts available, which allow you tocontrol some vehicle features withouthaving to follow the complete commandmenu. These are:• phone: "MOBILE NAME", "DIAL
NUMBER", "DIAL NAME", and "REDIAL"• CD player/CD changer: "DISC" and
"TRACK"
213
Voice control
• automatic climate control:"TEMPERATURE", "AUTO MODE","DEFROSTING/DEMISTING ON" and"DEFROSTING/DEMISTING OFF"
• radio: "TUNE NAME"• external device (USB): "TRACK"• external device (iPod): "TRACK"
Start communicating with the systemBefore you can start talking to the systemyou first have to press the VOICE buttonfor each operation and wait until thesystem answers with a beep. See VoiceControl (page 37).Press the button again to cancel the voicesession.
Name tagThe name tag functionality can supportthe phone, audio and navigation featuresby using the "STORE NAME" function. Youcan assign name tags to items such asfavourite radio stations and personalphone contacts. See Audio unitcommands (page 214). See Telephonecommands (page 222).
• Store up to 20 name tags per function.• The average recording time for each
name tag is approximately 2-3seconds.
AUDIO UNIT COMMANDSCD PlayerYou can control playback directly by voicecontrol.
OverviewThe overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
"CD PLAYER"
"HELP"
"PLAY"
"TRACK"*
"SHUFFLE ALL"
"SHUFFLE FOLDER"**
"SHUFFLE OFF"
"REPEAT FOLDER"**
"REPEAT TRACK"
214
Voice control
"CD PLAYER"
"REPEAT OFF"
* Can be used as a shortcut.** Only available if the CD contains audio data files like MP3 or WMA.
TrackYou can choose a track on your CD directly.
System answerUser saysSteps
"CD PLAYER""CD PLAYER"1
"TRACK NUMBER PLEASE""TRACK"*2
"TRACK <number>""<a number between 1 and 99>"**3
* Can be used as a shortcut.** Additionally, numbers can be spoken as up to four single digits (for example "2", "4","5" for track 245)
Shuffle allTo set random playback.
System answerUser saysSteps
"CD PLAYER""CD PLAYER"1
"SHUFFLE ALL"2
RadioThe radio voice commands support thefunctionality of the radio and allow you totune radio stations by voice control.
OverviewThe overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu.
"RADIO"
"HELP"
"AM"
215
Voice control
"RADIO"
"FM"
"TUNE NAME"*
"DELETE NAME"
"DELETE DIRECTORY"
"PLAY DIRECTORY"
"STORE NAME"
"PLAY"
* Can be used as a shortcut.
Tune frequencyThis function allows you to tune your radioby voice commands.
System answerUser saysSteps
"RADIO""RADIO"1
"AM FREQUENCY PLEASE""AM"2
"FM FREQUENCY PLEASE""FM"
"TUNE <frequency>""<frequency>"*3
* The frequency may be entered in a variety of ways. Refer below for representativeexamples.
FM band: 87.5 - 108.0 in increments of 0.1• "Eighty nine point nine" (89.9)• "Ninety" (90.0)• "One hundred point five" (100.5)• "One zero one point one" (101.1)• "One zero eight" (108.0)AM/MW band: 531 - 1602 in increments of9AM/LW band: 153 - 281 in increments of 1
• "Five thirty one" (531)• "Nine hundred" (900)• "Fourteen forty" (1440)• "Fifteen zero three" (1503)• "Ten eighty" (1080)
Store nameIf you have tuned a radio station, you canstore it with a name in the directory.
216
Voice control
System answerUser saysSteps
"RADIO""RADIO"1
"STORE NAME""STORE NAME"2"NAME PLEASE"
"REPEAT NAME PLEASE""<name>"3
"STORING NAME""<name>"4"<name> STORED"
Tune nameThis function allows you to call up a storedradio station.
System answerUser saysSteps
"RADIO""RADIO"1
"NAME PLEASE""TUNE NAME"*2
"TUNE <name>""<name>"3
* Can be used as a shortcut.
Delete nameThis function allows you to delete a storedradio station.
System answerUser saysSteps
"RADIO""RADIO"1
"NAME PLEASE""DELETE NAME"2
"DELETE <name>""<name>"3"CONFIRM YES OR NO"
"DELETED""YES"4
"COMMAND CANCELLED""NO"
217
Voice control
Play directory This function allows you to let the systemtell you all of the stored radio stations.
System answerUser saysSteps
"RADIO""RADIO"1
"PLAY <DIRECTORY>""PLAY DIRECTORY"2
Delete directoryThis function allows you to delete allstored radio stations at once.
System answerUser saysSteps
"RADIO""RADIO"1
"DELETE DIRECTORY""DELETE DIRECTORY"2"CONFIRM YES OR NO"
"RADIO DIRECTORY DELETED""YES"3
"COMMAND CANCELLED""NO"
PlayThis function switches the audio source tothe radio mode.
System answerUser saysSteps
"RADIO""RADIO"1
"PLAY"2
Auxiliary inputThis function allows you to switch theaudio source to the attached auxiliary inputdevice.
System answerUser saysSteps
"EXTERNAL DEVICE""EXTERNAL DEVICE"1
"LINE IN""LINE IN"2
218
Voice control
External devices - USBThese voice commands support thefunctionality of an external USB devicewhich may be connected to the audio unit.
OverviewThe overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
"EXTERNAL DEVICE", "USB"
"HELP"
"PLAY"
"TRACK"*
"PLAYLIST"**
"FOLDER"**
"SHUFFLE ALL"
"SHUFFLE FOLDER"
"SHUFFLE PLAYLIST"
"SHUFFLE OFF"
"REPEAT TRACK"
"REPEAT FOLDER"
"REPEAT OFF"
* Can be used as a shortcut.** Playlists and folders activated by voice control must be assigned special filenames.
USB playThis function allows you to switch theaudio source to the attached USB device.
System answerUser saysSteps
"EXTERNAL DEVICE""EXTERNAL DEVICE"1
"USB""USB"2
"PLAY"3
219
Voice control
USB Track You can choose a track on your USB devicedirectly.
System answerUser saysSteps
"EXTERNAL DEVICE""EXTERNAL DEVICE"1
"USB""USB"2
"TRACK NUMBER PLEASE""TRACK"3
"TRACK <number>""<a number between 1 and 99>"*4
* Additionally, numbers can be spoken as up to four single digits (for example "2", "4","5" for track 245)
External devices - iPodThese voice commands support thefunctionality of an iPod which may beconnected to the audio unit.
OverviewThe overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
"EXTERNAL DEVICE", "IPOD"
"HELP"
"PLAY"
"TRACK"*
"PLAYLIST"**
"SHUFFLE ALL"
"SHUFFLE PLAYLIST"
"SHUFFLE OFF"
"REPEAT TRACK"
"REPEAT OFF"
* Can be used as a shortcut.** Playlists activated by voice control must be assigned special filenames.
220
Voice control
iPod Track You can choose a track off the all titles listof your iPod directly.
System answerUser saysSteps
"EXTERNAL DEVICE""EXTERNALDEVICE"
1
"IPOD""IPOD"2
"TRACK NUMBERPLEASE""TRACK"*3
"TRACK <number>""<a numberbetween 1 and
99>"**
4
* Can be used as a shortcut.** Additionally, numbers can be spoken as up to five single digits (for example "5", "2","4", "5", "3" for track 52453), to a limit of 65535.
iPod playlistYou can choose a playlist from your iPoddirectly.
System answerUser saysSteps
"EXTERNAL DEVICE""EXTERNALDEVICE"
1
"IPOD""IPOD"2
"PLAYLIST NUMBERPLEASE""PLAYLIST"*3
"PLAYLIST <number>""<a numberbetween 1 and 10>"
4
* Playlists activated by voice control must be assigned special filenames.
External devices - BluetoothThese voice commands support thefunctionality of Bluetooth® which may beconnected to the audio unit.
OverviewThe overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
221
Voice control
"EXTERNAL DEVICE", "BLUETOOTH"
"HELP"
"PLAY"
"SHUFFLE ALL"
"SHUFFLE OFF"
"REPEAT TRACK"
"REPEAT OFF"
TELEPHONE COMMANDSPhoneYour phone system allows you to createan additional phonebook. The storedentries can be dialled by voice control.Phone numbers stored by using voicecontrol are stored on the vehicle systemand not in your phone.
OverviewThe overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
"PHONE"
"HELP"
"MOBILE NAME"*
"DIAL NUMBER"*
"DIAL NAME"*
"DELETE NAME"
"DELETE DIRECTORY"
"PLAY DIRECTORY"
"STORE NAME"
"REDIAL"*
"ACCEPT CALLS"
222
Voice control
"PHONE"
"REJECT CALLS"
* Can be used as a shortcut.
Phone functionsDial numberPhone numbers can be dialled after givingthe name tag voice command.
System answerUser saysSteps
"PHONE""PHONE"1
"NUMBER PLEASE""DIAL NUMBER"*2
"<phone number>"<phone number>"3CONTINUE?"
"DIALLING""DIAL"4
"<repeat last part of number>"CORRECTION"CONTINUE?"
* Can be used as a shortcut.
Dial namePhone numbers can be dialled after givingthe name tag voice command.
System answerUser saysSteps
"PHONE""PHONE"1
"NAME PLEASE""DIAL NAME"*2
"DIAL <name>""<name>"3"CONFIRM YES OR NO"
"DIALLING""YES"4
"COMMAND CANCELLED""NO"
* Can be used as a shortcut.
223
Voice control
Redial This function allows you to redial the lastdialled phone number.
System answerUser saysSteps
"PHONE""PHONE"1
"REDIAL""REDIAL"*2"CONFIRM YES OR NO"
"DIALLING""YES"3
"COMMAND CANCELLED""NO"
* Can be used as a shortcut.
Mobile nameThis function allows you to access phonenumbers stored with a name tag in yourmobile phone.
System answerUser saysSteps
"PHONE""PHONE"1
"MOBILE NAME" "<phonedependent dialogue>""MOBILE NAME"*2
* Can be used as a shortcut.
DTMF (Tone dialling)This function transfers spoken numbersinto DTMF tones. For example, to make aremote enquiry to your home answeringmachine or to enter a PIN number etc.
Note: DTMF can only be used during anongoing call. Operate the VOICE button andwait for the system prompt.Can only be used with vehicles installed witha dedicated VOICE button.
System answerUser saysSteps
"NUMBER PLEASE"1
"<numbers 1 to 9, zero, hash, star>"2
224
Voice control
Create a phonebookStore name
New entries can be stored with the"STORE NAME" command. This featurecan be used to dial a number by calling upthe name instead of the full phone number.
System answerUser saysSteps
"PHONE""PHONE"1
"STORE NAME""STORE NAME"2"NAME PLEASE"
"REPEAT NAME PLEASE""<name>"3
"STORING NAME""<name>"4"<name> STORED""NUMBER PLEASE"
"<phone number>""<phone number>"5
"STORING NUMBER""STORE"6"<phone number>""NUMBER STORED"
Delete nameStored names can also be deleted fromthe directory.
System answerUser saysSteps
"PHONE""PHONE"1
"NAME PLEASE""DELETE NAME"2
"DELETE <name>""<name>"3"CONFIRM YES OR NO"
"<name> DELETED""YES"4
"COMMAND CANCELLED""NO"
Play directoryUse this function to let the system tell youall stored entries.
225
Voice control
System answerUser saysSteps
"PHONE""PHONE"1
"PLAY DIRECTORY""PLAY DIRECTORY"2
Delete directoryThis function allows you to delete allentries in one go.
System answerUser saysSteps
"PHONE""PHONE"1
"DELETE DIRECTORY""DELETE DIRECTORY"2"CONFIRM YES OR NO"
"DIRECTORY DELETED""YES"3
"COMMAND CANCELLED""NO"
Main settingsReject callsCalls can be set to be automaticallyrejected using voice control.
System answerUser saysSteps
"PHONE""PHONE"1
"REJECT CALLS""REJECT CALLS"2
"ACCEPT CALLS""ACCEPT CALLS"*
* use this command to turn the reject mode off
226
Voice control
CLIMATE CONTROLCOMMANDSClimateThe climate voice commands supports thefunctionality of the fan speed, temperatureand mode settings. Not all functions areavailable on all vehicles.
OverviewThe overview below shows the availablevoice commands. The following lists willgive further information about thecomplete command menu in selectedexamples.
"CLIMATE"
"HELP"
"FAN"*
"DEFROSTING/DEMISTING ON"*
"DEFROSTING/DEMISTING OFF"*
"TEMPERATURE"*
"AUTO MODE"*
* Can be used as a shortcut.
FanThis function allows you to adjust the fanspeed.
System answerUser saysSteps
"CLIMATE""CLIMATE"1
"FAN SPEED PLEASE""‘FAN"*2
"FAN MINIMUM""MINIMUM"
3 "FAN <number>""<a number between 1 and 7>"
"FAN MAXIMUM""MAXIMUM"
* Can be used as a shortcut.
227
Voice control
Defrosting/Demisting
System answerUser saysSteps
"CLIMATE""CLIMATE"1
"DEFROSTING ON/DEMISTING ON""DEFROSTING ON/DEMISTING
ON"*
2"DEFROSTING OFF/DEMISTING
OFF""DEFROSTING OFF/DEMISTING
OFF"*
* Can be used as a shortcut.
TemperatureThis function allows you to adjust thetemperature.
System answerUser saysSteps
"CLIMATE""CLIMATE"1
"TEMPERATURE PLEASE""TEMPERATURE"*2
"TEMPERATURE MINIMUM""MINIMUM"
3 "TEMPERATURE <number>""<a number between 15 and 29 °C
with 0.5 increments>" or "<anumber between 59 and 84 °F>"
"TEMPERATURE MAXIMUM""MAXIMUM"
* Can be used as a shortcut.
Auto mode
System answerUser saysSteps
"CLIMATE""CLIMATE"1
"AUTO MODE""AUTO MODE"*2
* Can be used as a shortcut. Can be deactivated by selecting a different temperature orfan speed.
228
Voice control
GENERAL INFORMATION
CAUTIONSTake care when handling externaldevices with exposed electricalconnectors (such as the USB plug).
Always replace the protective cap/shieldwhen possible. There may be a risk ofelectrostatic discharge causing damageto the device.
Do not touch or handle the USBsocket in the vehicle. Cover the socketwhen not in use.Only use USB Mass-Storage devicecompliant devices.Always switch your audio unit to adifferent source (for example theradio) before unplugging the USB
device.Do not install or connect USB hubs orsplitters.
Note: The system is only designed torecognize and read suitable audio files froma USB device that conforms to the USBMass-Storage device class or an iPod. Notall available USB devices can be guaranteedto function with the system.Note: It is possible to connect compatibledevices with a trailing USB lead as well asthose that plug into the vehicle USB socketdirectly (for example USB memory sticksand pen drives).Note: Some USB devices with a higherpower consumption may not be compatible(for example some larger hard drives).Note: Access time to read the files on theexternal device will vary depending uponfactors such as the file structure, size anddevice content.
The system supports a range of externaldevices, to fully integrate with your audiounit via the USB and auxiliary inputsockets. Once connected, control of theexternal device is possible via the audiounit.A list of typical compatible devices areshown below:• USB memory sticks• USB portable hard drives• Some MP3 players with USB
connection• iPod media players (refer to
www.ford-mobile-connectivity.com for latestcompatibility list).
The system is USB 2.0 full speedcompatible, USB 1.1 host compliant andsupports FAT 16/32 file systems.
Information on audio filestructures for external devicesUSBCreate only a single partition on the USBdevice.If playlists are created, they must containcorrect file paths referenced to the USBdevice. It is recommended to create theplaylist after the audio files have beentransferred to the USB device.Playlists must be created in .m3u format.Audio files must be in .mp3 format.Do not exceed the following limits:• 1000 items per folder (files, folders and
playlists)• 5000 folders per USB device (including
playlists)• 8 subfolder levels.
229
Connectivity
To enable voice control for customplaylists and folders, follow the procedurebelow:• Create folders named with the
structure "Ford<*>" where <*> is anumber 1-10. For example "Ford3"without an extension.
• Create playlists named with thestructure "Ford<*>.m3u" where <*>is a number 1-10. For example"Ford5.m3u" without any spacebetween "Ford" and the number.
Thereafter, custom folders and playlistswill be selectable with voice control. SeeAudio unit commands (page 214).
iPodTo enable voice control for customplaylists, create playlists named with thestructure "Ford<*>" where <*> is anumber 1-10. For example "Ford7" withoutany space between "Ford" and thenumber.Thereafter, playlists will be selectable withvoice control. See Audio unit commands(page 214).
CONNECTING AN EXTERNALDEVICE
WARNINGMake sure the external device issecurely mounted within the vehicle,and that trailing connections do not
obstruct any of the driving controls.
External devices may be connected usingthe auxiliary input socket and the USB port.See Auxiliary input (AUX IN) socket(page 82). See USB port (page 82).
ConnectionPlug in the device, and if necessary secureit to prevent movement within the vehicle.
Connecting an iPodConnect the USB cable from the iPod tothe vehicle USB socket.
CONNECTING AN EXTERNALDEVICE - VEHICLES WITH:BLUETOOTHConnecting a Bluetooth audiodevice
CAUTIONAs various standards exist,manufacturers are able to implementa variety of profiles in their Bluetooth
devices. Because of this, an incompatibilitycan occur between the Bluetooth deviceand the system, which in some cases maylimit system functionality. To avoid thissituation, only recommended devicesshould be used.
Please visit the websitewww.ford-mobile-connectivity.comfor full details.
Bonding the deviceNote: Some audio and navigation unitshave a separate Bluetooth audio menu. Usethis to access setup and control.To connect the device to the system followthe same procedure as for Bluetooth handsfree phones. See Bluetooth setup (page209).
Operating the deviceSelect Bluetooth audio as the activesource.
230
Connectivity
Tracks can be accessed by skippingforwards and backwards using the steeringwheel controls, or directly from the audiounit controls.
USING A USB DEVICEVarious icons are used to identify types ofaudio file, folders etc.
E100029
USB device is the active source
E100022
Folder
E100023
Playlist
E100024
Album
E100025
Artist
E100026
Filename
E100027
Track title
E100028
Information not available
USBOperationSelect the USB device as the audio sourceby repeatedly pressing the CD/AUXbutton until USB appears in the display.After first connecting the USB device, thefirst track within the first folder will startto play automatically. Subsequently,following audio source switching, theposition of playback on the USB device isremembered.To browse the device contents, press theup/down arrow key or the OK button once.The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of
the display shows the current positionof the folder view.
• ">" after an entry indicates a furtherlevel down is readable (for example afolder named after an album, withindividual album tracks within thatfolder).
• "<" before the list indicates that afurther level up is readable.
• Icons to the left of track/folder textindicate the type of file/folder. Referto the list for an explanation of theseicons.
To navigate the USB device contents, usethe up/down arrow keys to scroll throughlists, and the left/right keys to move up ordown within the folder hierarchy. Once yourdesired track, playlist or folder ishighlighted, press the OK button to selectplayback.Note: If you wish to jump to the top levelof the USB device contents, press and holdthe left arrow key.
231
Connectivity
Audio controlPress the left and right arrow keys to skipbackwards and forwards through tracks.Press and hold the left/right arrow keys toenable fast rewind/fast forward throughtrack content.Press the up/down arrow key or the OKbutton to browse the device contents.Press the MENU key to enter the USBmenu. It is possible to enable shuffle andrepeat functions here with respect tofolders and playlists.Press the SCAN button to scan the wholedevice, current folder or a playlist if it is inoperation.Press the INFO button to display thefollowing:• filename• title• artist• album• track number and playing time.Repeated button presses will scrollthrough these displays.
SD Navigation unitsOperationSelect the USB device as the audio sourceby pressing the CD/AUX button until theUSB button appears to the left of thedisplay. Select USB from the availabledevice list.Note: Some devices may be shown but notselectable, depending if the device isconnected or not.After first connecting the USB device, thefirst track within the first folder will startto play automatically. Subsequently,following audio source switching, theposition of playback on the USB device isremembered.
To browse the device contents, press thescroll up or down arrow button.The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of
the display shows the current positionof the folder view.
• ">" after an entry indicates a furtherlevel down is readable (for example afolder named after an album, withindividual album tracks within thatfolder).
• "<" to the left hand side of the displayindicates that a further level up isreadable.
• Icons to the left of track/folder textindicate the type of file/folder. Referto the list for an explanation of theseicons.
To navigate the USB device contents, usethe scroll buttons to browse through lists.Push the button to expand the contentswithin the highlighted playlist or folder, orto commence playback of a particulartrack. Press the left arrow key to go up onelevel.
Audio controlPress the SEEK up and down keys to skipbackwards and forwards through tracks.Press and hold the SEEK keys to enablefast rewind/fast forward through trackcontent.Press the scroll bar arrow keys to browsethe device contents.Press SHUFFLE or REPEAT buttons toenable shuffle and repeat functions withrespect to folders and playlists.Press the SCAN button to scan the currentplaylist if it is in operation, or the completeUSB device or folder.
232
Connectivity
Press the INFO button to display thefollowing:• filename• title• artist• album• track number and playing time.
USING AN IPODVarious icons are used to identify types ofaudio file, folders etc.
E100030
iPod is the active source
E100031
iPod playlist
E100032
iPod artist
E100033
iPod album
E100034
iPod genre
E100035
iPod song
E100036
iPod generic category
E100037
iPod generic media file
RadioOperationConnect the iPod. See Connecting anexternal device (page 230).
Select the iPod as the audio source byrepeatedly pressing the CD/AUX buttonuntil iPod appears in the display.The iPod menu list for browsing contentswill be available through the radio display.Navigation of the contents follows thesame principles as for iPod standalone use(for example search by artist, title, etc.).To browse the iPod contents, press theup/down arrow key or the OK button once.The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of
the display shows the current positionof the list view.
• ">" after an entry indicates a furtherlevel down is readable (for example allalbums by a particular artist).
• "<" before the list indicates that afurther level up is readable.
• An icon on the left side indicates thetype of the currently displayed list (forexample list of albums). Refer to thelist for an explanation of these icons.
To navigate the iPod contents, use theup/down arrow keys to scroll through lists,and the left/right keys to move up or downwithin the hierarchy. Once your desiredtrack, playlist, album, artist or genre ishighlighted, press the OK button to selectplayback.Note: If you wish to jump to the top levelof the iPod contents, press and hold the leftarrow key.
Audio controlPress the left and right arrow keys to skipbackwards and forwards through tracks.Press and hold the left/right arrow keys toenable fast rewind/fast forward throughtrack content.
233
Connectivity
Press the up/down arrow key or the OKbutton to browse the iPod contents.Press the MENU key to enter the iPodmenu. It is possible to enable shuffle andrepeat functions here. It is also possible toenable the iPod "Shuffle songs" optiondirectly from the top level.Press the SCAN button to scan thecurrently selected tracks.Press the INFO button to display thefollowing:• title• artist• track number and playing time.Repeated button presses will scrollthrough these displays.
SD Navigation unitsOperationConnect the iPod. See Connecting anexternal device (page 230).Select the iPod as the audio source bypressing the CD/AUX button until the iPodbutton appears to the left of the display.Select iPod from the available device list.Note: Some devices may be shown but notselectable, depending if the device isconnected or not.The iPod menu list for browsing contentswill be available through the display.Navigation of the contents follows thesame principles as for iPod standalone use(for example search by artist, title, etc.).To browse the iPod contents, press thescroll up or down arrow button.
The display will show the trackinformation, together with other importantinformation described below:• A vertical scroll bar on the right side of
the display shows the current positionof the list view.
• ">" after an entry indicates a furtherlevel down is readable (for example allalbums by a particular artist).
• "<" before the list indicates that afurther level up is readable.
• An icon on the left side indicates thetype of the currently displayed list (forexample list of albums). Refer to thelist for an explanation of these icons.
To navigate the iPod contents, use thescroll buttons to browse through lists. Pushthe button to expand the contents withinthe highlighted playlist, album, artist, genreor to commence playback of a particulartrack. Press the left arrow key to go up onelevel.
Audio controlPress the SEEK up and down keys to skipbackwards and forwards through tracks.Press and hold the SEEK keys to enablefast rewind/fast forward through trackcontent.Press the scroll bar arrow keys to browsethe iPod contents.Press the MENU key to enter the iPodmenu. It is possible to enable shuffle andrepeat functions here. It is also possible toenable the iPod "Shuffle songs" optiondirectly from the top level.Press the SCAN button to scan thecurrently selected tracks.Press the INFO button to display thefollowing:• title• artist• track number and playing time.
234
Connectivity
TYPE APPROVALSFCC/INDUSTRY CANADA NOTICEThis device complies with Part 15 of theFCC Rules. Operation is subject to thefollowing two conditions: (1) this devicemay not cause harmful interference, and(2) this device must accept anyinterference received, includinginterference that may cause undesiredoperation.FCC ID: WJLRX-42IC: 7847A-RX42Changes or modifications to your devicenot expressly approved by the partyresponsible for compliance can void theuser's authority to operate the equipment.
RX-42 - declaration of conformityWe, the party responsible for compliance,declare under our sole responsibility thatthe Handset Integration product RX-42 isin conformity with the provisions of thefollowing Council Directive: 1999/5/EC. Acopy of the Declaration of Conformity canbe found at:www.novero.com/declaration_of_conformityThe Bluetooth word mark and logos areowned by the Bluetooth SIG, Inc. and anyuse of such marks by Ford Motor Companyis under license. Other trademarks andtrade names are those of their respectiveowners.
TYPE APPROVALSiPod is a trademark of Apple Inc.
TYPE APPROVALS
E97713
E97714
SD Logo is a trademark.
ELECTROMAGNETICCOMPATIBILITY
WARNINGSYour vehicle has been tested andcertified to legislations relating toelectromagnetic compatibility
(72/245/EEC, UN ECE Regulation 10 orother applicable local requirements). It isyour responsibility to ensure that anyequipment you have fitted complies withapplicable local legislations. Have anyequipment fitted by properly trainedtechnicians.
The RF (radio frequency) transmitterequipment (e.g. cellular telephones,amateur radio transmitters etc.) may
only be fitted to your vehicle if they complywith the parameters shown in the tablebelow. There are no special provisions orconditions for installations or use.
Do not mount any transceiver,microphones, speakers, or any otheritem in the deployment path of the
airbag system.Do not fasten antenna cables tooriginal vehicle wiring, fuel pipes andbrake pipes.
235
Appendices
WARNINGSKeep antenna and power cables atleast 10 centimetres (4 inches) from
WARNINGSany electronic modules and airbags.
3 8
4
57
6
E139668
Antenna PositionsMaximum output power Watt (PeakRMS)
Frequency BandMHz
8100 W1 - 30
3, 4, 5100 W50 - 54
3, 4, 550 W68 – 87.5
3, 4, 550 W142 – 176
3, 4, 550 W220 - 225
3, 4, 550 W380 – 512
3, 4, 5, 6*, 7*10 W806 – 870
3, 4, 5, 6*, 7*10 W870 - 940
3, 4, 510 W1200 – 1400
3, 4, 5, 6*, 7*10 W1710 – 1885
3, 4, 5, 6*, 7*10 W1885 – 2025
*Only for GSM/3G cellular phones, with a patch antenna installed inside of the frontwindscreen.
236
Appendices
Note: Position 6 & 7 are patch antennas, 8is the towbar.Note: After the installation of RFtransmitters, check for disturbances fromand to all electrical equipment in thevehicle, both in the standby and transmitmodes.Check all electrical equipment:• with the ignition ON• with the engine running• during a road test at various speeds.Check that electromagnetic fieldsgenerated inside the vehicle cabin by thetransmitter installed do not exceedapplicable human exposure requirements.
237
Appendices
44WD
See: Four-Wheel Drive.......................................92
AA/C
See: Climate Control..........................................66About This Manual...........................................7ABS
See: Brakes.............................................................97ABS driving hints
See: Hints on Driving With Anti-LockBrakes..................................................................97
AccessoriesSee: Parts and Accessories.................................8
Adjusting the Steering Wheel...................36Air Conditioning
See: Climate Control..........................................66Air Vents............................................................66Alarm..................................................................34
Principle of Operation........................................34Alternative frequencies..............................198Antenna..........................................................206Appendices....................................................235Arming the alarm...........................................35Arming the engine immobiliser.................33Ashtray...............................................................79At a Glance..........................................................9
Adjusting the steering wheel............................12Airbag.........................................................................14Automatic climate control.................................13Direction indicators...............................................13Instrument panel overview - Left-hand
drive.......................................................................10Instrument panel overview - Right-hand
drive........................................................................9Locking and unlocking..........................................11Manual climate control.......................................12Manual transmission...........................................14Refuelling.................................................................14
Audible Warnings and Indicators............60Alarm warning......................................................60Direction indicators warning............................60Door open warning.............................................60Home safe..............................................................60Key in ignition warning.......................................60Lights on warning................................................60Low fuel level warning.......................................60Low washer fluid warning..................................61Missed lock warning.............................................61Not in park warning.............................................60One side park light..............................................60Over speed warning............................................60Parking brake warning.......................................60Restraints back-up warning............................60Seat belt reminder..............................................60Turn indicator........................................................60
Audio Control...................................................36Mode.........................................................................36Seek...........................................................................36
Audio introduction.......................................184Audio system care......................................206Audio system security.................................192Audio troubleshooting...............................207Audio unit clock and date displays........193Audio unit commands................................214
Auxiliary input......................................................218CD Player...............................................................214External devices - Bluetooth..........................221External devices - iPod....................................220External devices - USB.....................................219Radio........................................................................215
Audio unit menus.........................................198Audio unit operation....................................195Audio unit overview.....................................185Autolamps........................................................42Automatic Climate Control........................69
Air distribution control.......................................69Blower......................................................................69Cooling the interior quickly...............................70Recirculated air.....................................................70Switching off the automatic climate
control...................................................................71Switching the air conditioning on and
off...........................................................................71Temperature control...........................................70Windscreen defrosting and demisting..........71
239
Index
Automatic Transmission.............................94Drive modes...........................................................96Emergency park position release
button..................................................................96Hints on driving with an automatic
transmission.....................................................96Selector lever positions.....................................94
Automatic volume control........................198Autostore control.........................................196
Type 1......................................................................196Type 2, 3, 4 and 5................................................196
Autowipers.......................................................38Auxiliary input (AUX IN) socket................82Auxiliary Power Points.................................80
BBattery connection points.........................153Battery warning symbols...........................153
Battery lables.......................................................153Bluetooth setup...........................................209
Handling of phones..........................................209Requirements for Bluetooth
connection......................................................209Bonnet Lock
See: Opening and Closing the Bonnet........135Booster cables
See: Jump-Starting the Vehicle.....................152Booster Seats..................................................20
Booster cushion (Group 3)................................21Booster seat (Group 2)......................................20
Brake and Clutch Fluid Check..................145Brakes.................................................................97
Principle of Operation.........................................97Bulb changing
See: Changing a Bulb.........................................45Bulb Specification Chart..............................51
CCapacities and Specifications.................163
Technical Specifications..................................163Car Wash
See: Cleaning the Exterior...............................150Catalytic Converter........................................87
Driving with a catalytic converter...................87
Changing a Bulb.............................................45Centre high mount stop lamp.........................49Exterior mirror lamps...........................................47Front fog lamps.....................................................47Front reading lamps............................................49Headlamp main and dipped beam...............46Interior lamp..........................................................49Number plate lamp.............................................48Rear lamps..............................................................47Side lamps and front direction
indicators............................................................46Side repeaters........................................................47
Changing a Fuse............................................125Changing a Road Wheel............................154
Installing a road wheel.....................................159Jacking and lifting points..................................157Locking wheel nuts............................................154Removing a road wheel...................................158Spare wheel.........................................................156Stowing the wheel.............................................160Vehicle jack...........................................................154
Changing the remote controlbattery.............................................................28
Changing the Wiper Blades.......................39Service position....................................................40Windscreen wiper blades.................................39
Checking the Wiper Blades........................39Child Safety.......................................................16Child Safety Locks...........................................21
Left-hand side........................................................21Right-hand side......................................................21
Child Seat Positioning....................................17Child Seats.........................................................16
Child restraints for different massgroups...................................................................16
Cigar Lighter.....................................................79Cleaning the Exterior...................................150
Body paintwork preservation........................150Cleaning the chrome trim...............................150Cleaning the headlamps.................................150Cleaning the rear window...............................150
Cleaning the Interior....................................150Instrument cluster screens, LCD screens,
radio screens....................................................151Rear windows........................................................151Seat belts..............................................................150
Climate Control..............................................66Principle of Operation........................................66
240
Index
Climate control commands.....................227Climate...................................................................227
Clock....................................................................79Coded keys........................................................33Cold Weather Precautions........................120Compact disc playback............................200Compact disc player..................................200Compact disc track scanning..................201
Type 1.......................................................................201Type 2......................................................................201Type 3, 4 and 5....................................................201
Connecting an external device...............230Connection...........................................................230
Connecting an external device - VehiclesWith: Bluetooth.........................................230Connecting a Bluetooth audio
device................................................................230Connectivity...................................................229
General Information.........................................229Convenience features...................................79Coolant Check
See: Engine Coolant Check............................144Cool Box............................................................82Cruise Control................................................109
Principle of Operation......................................109Cruise control
See: Using Cruise Control...............................109Cup Holders.....................................................80
Front cup holders.................................................80Rear cup holders....................................................81
DDiesel Particulate Filter................................85
Regeneration.........................................................86Digital signal processing (DSP)..............198
Changing the DSP settings............................198DSP equaliser......................................................198DSP occupancy...................................................198
Direction Indicators.......................................45Disabling the passenger airbag................25
Disabling the passenger airbag......................26Enabling the passenger airbag.......................26Fitting the passenger airbag deactivation
switch..................................................................26Disarming the alarm.....................................35Disarming the engine immobiliser...........33
DPFSee: Diesel Particulate Filter............................85
Draining the Fuel Filter Water Trap........145Driving Hints...................................................120Driving Through Water.................................121
Driving through water ........................................121
EElectric exterior mirrors................................54
Electric folding mirrors.......................................55Electromagnetic compatibility...............235Electronic Locking Differential..................93Ending compact disc playback..............204Engine Coolant Check................................144
Checking the coolant level..............................144Topping up............................................................144
Engine immobiliser........................................33Principle of Operation.........................................33
Engine Oil Check...........................................143Checking the oil level........................................143Topping up.............................................................143
Engine Oil Dipstick - 2.2L Duratorq-TDCi(Puma) Diesel/3.2L Duratorq-TDCi(Puma) Diesel.............................................143
Engine Oil Dipstick - 2.5L Duratec-HE(122kW/165PS) - MI4...............................143
Exterior Mirrors................................................54Manual folding mirrors.......................................54
FFastening the seat belts..............................24Fast forward/reverse.................................200First Aid Kit......................................................122Floor Mats.........................................................83Fog Lamps - Front
See: Front Fog Lamps........................................42Fog Lamps - Rear
See: Rear Fog Lamps..........................................43Four-Wheel Drive...........................................92
Four-wheel drive, high range (4H).................92Four-wheel drive, low range (4L)...................92Shifting between 2H and 4H...........................93Shifting between 2H and 4L............................93Shifting between 4H and 4L............................93Two-wheel drive, high range (2H).................92
241
Index
Front Fog Lamps............................................42Adjustment.............................................................42Control lever...........................................................42
Front Seats........................................................72Adjusting the angle of the seatback
(Electric seats).................................................75Adjusting the angle of the seatback
(Manual seats).................................................73Adjusting the height of the driver’s seat
(Electric seats).................................................75Adjusting the height of the driver’s seat
(Manual seats).................................................73Adjusting the lumbar support..........................72Folding the seat backrest (Bench seat -
Single cab).........................................................74Moving the seats backwards and forwards
(Electric seats).................................................74Moving the seats backwards and forwards
(Manual seats).................................................73Tilting the seat (Electric seats).......................75
Fuel and Refuelling........................................87Technical Specifications...................................90
Fuel Consumption.........................................90Fuel Consumption
See: Technical Specifications.........................90Fuel filler flap..................................................88
Filling........................................................................89Vehicle equipped with capless
system.................................................................89Vehicles equipped with cap system.............88
Fuel Quality - Diesel......................................87Long-term storage...............................................87
Fuel Quality - Petrol......................................87Fuse Box Locations......................................124
Engine compartment fuse box......................125Passenger compartment fuse box..............124
Fuses.................................................................124Fuse Specification Chart...........................126
Engine compartment fuse box......................126Passenger compartment fuse box................131
GGauges...............................................................56
Engine coolant temperature gauge..............56Fuel gauge..............................................................56
GearboxSee: Transmission................................................92
General Driving Points................................120Vehicles with a diesel engine.........................120
General Information on RadioFrequencies....................................................27
Glasses Holder.................................................81Global Opening and Closing.......................31
Global closing........................................................32Global opening.......................................................31
HHandbrake
See: Parking Brake...............................................97Hazard Warning Flashers............................44HDC
See: Hill descent control (HDC).....................98See: Using Hill Descent Control.....................98
Headlamp Levelling......................................44Head Restraints..............................................76
Adjusting the head restraint.............................76Removing the head restraint............................76
Heated Seats....................................................77Heated Windows and Mirrors.....................71
Heated exterior mirrors........................................71Heated windows....................................................71
HeatingSee: Climate Control..........................................66
Hill descent control (HDC)........................98Principle of Operation........................................98
Hill descent control (HDC)See: Using Hill Descent Control.....................98
Hill launch assist (HLA)See: Using hill start assist...............................102
Hill Start Assist..............................................102Principle of Operation.......................................102
Hints on Driving With Anti-LockBrakes..............................................................97
HLASee: Hill Start Assist..........................................102See: Using hill start assist...............................102
IIgnition Switch................................................84Immobiliser
See: Engine immobiliser....................................33
242
Index
Important audio information...................184Audio unit labels.................................................184Disc labels.............................................................184
Information Displays.....................................62General Information............................................62
Instrument Cluster........................................56Instrument Lighting Dimmer......................79Interior Lamps.................................................45
Courtesy lamp.......................................................45Reading lamps......................................................45
Introduction.........................................................7iPod connection
See: Connecting an external device...........230See: Connecting an external device - Vehicles
With: Bluetooth.............................................230iPod
See: Using an iPod.............................................233ISOFIX Anchor Points....................................19
Attaching a child restraint with a toptether....................................................................19
JJump starting
See: Jump-Starting the Vehicle.....................152Jump-Starting the Vehicle........................152
To connect the booster cables......................152To start the engine.............................................152
KKeys and Remote Controls.........................27
LLighting Control...............................................41
Approach lamps...................................................42Emergency stop lights........................................42Headlamp flasher.................................................41Home safe lighting................................................41Lighting control positions..................................41Main and dipped beam.......................................41Parking lamps.........................................................41
Lighting...............................................................41Load Carriers
See: Roof Racks and Load Carriers...............114Load Carrying...................................................111
General Information............................................111
Loading the navigation data.....................176Loading the navigation data...........................176
Load Retaining Fixtures................................111Load rest.................................................................113Rope hooks.............................................................111Tie down points....................................................112
Locking and Unlocking.................................29Child play protection function........................30Driver configuration mode................................30Locking and unlocking the doors from
inside....................................................................30Locking and unlocking the doors with the
key.........................................................................29Locking and unlocking the doors with the
remote control..................................................29Locking the doors individually with the
key..........................................................................31Locks...................................................................29
MMaintenance...................................................135
General Information..........................................135Technical Specifications..................................146
Manual Climate Control..............................66Air distribution control.......................................66Blower.......................................................................67Recirculated air......................................................67System settings.....................................................67Temperature control...........................................67
Manual Transmission...................................92Selecting reverse gear........................................92
Map updates..................................................183Message Centre
See: Information Displays.................................62Mirrors
See: Heated Windows and Mirrors..................71See: Windows and Mirrors................................52
MP3 connectionSee: Connecting an external device...........230See: Connecting an external device - Vehicles
With: Bluetooth.............................................230MP3 display options...................................203
CD text display options...................................203
243
Index
MP3 file playback.........................................201File formats..........................................................202ID3 Tag Version 2...............................................203ISO 9660 format................................................201MP3 files playback order................................202MP3 navigation..................................................203Multi session........................................................202Playing a multi session disc...........................202
NNavigation introduction...............................171
General Information............................................171Navigation Quick start.................................173
Vehicles with SD navigation system............173Navigation system.......................................180Navigation unit overview............................174
Vehicles with SD navigation system............175News broadcasts.........................................198
OOccupant protection.....................................22
Principle of Operation.........................................22Oil Check
See: Engine Oil Check.......................................143On/off control................................................195Opening and Closing the Bonnet...........135
Closing the bonnet.............................................136Opening the bonnet...........................................135
PParking Aids...................................................104
Principle of Operation......................................104Parking Brake...................................................97Parts and Accessories....................................8Personalised Settings..................................65
Language setting.................................................65Units of measure..................................................65
Power Door LocksSee: Locking and Unlocking.............................29
Power Steering Fluid Check......................145Topping up............................................................145
Power Windows..............................................52Anti-trap function (vehicles with GO/GC
only).....................................................................53Driver’s door switches (Double cab)............52Driver’s door switches (Single and Stretch
cab).......................................................................52Front and rear passengers’ door
switches..............................................................52Global opening and global closing (GO/GC)
(If fitted).............................................................53Opening and closing the windows
automatically....................................................52Resetting the memory of the electric
windows..............................................................53Safety mode...........................................................53Safety switch for the rear windows...............53
Programming the remote control............27Programming a new remote control.............27Programming the additional key....................27Reprogramming the unlocking
function...............................................................27
RRear Fog Lamps..............................................43Rear Seats.........................................................76
Folding the rear seatback - Doublecab.........................................................................77
Folding the rear seat cushion...........................76Rear seat arm rest.................................................77
Rear view camera.........................................107Principle of Operation.......................................107
Reduced Engine Performance.................120Refuelling..........................................................90Regional mode (REG)................................199Remote control battery
See: Changing the remote controlbattery.................................................................28
Remote control programmingSee: Programming the remote control.........27
Repairing Minor Paint Damage.................151Repeat compact disc tracks...................200
Type 1.....................................................................200Type 2......................................................................201Type 3, 4 and 5....................................................201
Road Safety......................................................171Safety information..............................................172
Roadside Emergencies...............................122
244
Index
Roof Racks and Load Carriers..................114Roof rack.................................................................114
Route displays................................................181Junction zoom.......................................................181Map display............................................................181Navigation display...............................................181
Route options menu...................................180Driver.......................................................................180Dynamic.................................................................180Eco settings..........................................................180Ferry/motorail......................................................180Motorway..............................................................180Route......................................................................180Seasonal roads.....................................................181Toll...........................................................................180Toll sticker..............................................................181
Running-In.......................................................120Brakes and clutch...............................................120Engine.....................................................................120Tyres........................................................................120
SSafety Precautions........................................87Seat belt height adjustment......................24Seat belt reminder.........................................25
Deactivating the seat belt reminder..............25Seat belts
See: Fastening the seat belts...........................24Seats....................................................................72Security code.................................................192Setting the clock on the audio unit........193
...................................................................................194Changing the time..............................................193Exact hour adjustment.....................................193
Shuffle/random...........................................200Type 1.....................................................................200Type 2....................................................................200Type 3, 4 and 5...................................................200
Sitting in the Correct Position....................72Sliding Windows.............................................55Snow Chains
See: Using Snow Chains...................................161Sound button.................................................195Speed Control
See: Cruise Control............................................109Stability Control...........................................100
Principle of Operation......................................100
Starter SwitchSee: Ignition Switch............................................84
Starting a Diesel Engine..............................85Cold or hot engine...............................................85
Starting and Stopping the Engine...........84General Information...........................................84
Starting a Petrol Engine..............................84Cold or hot engine...............................................84Engine idle speed after starting......................85Flooded engine.....................................................85
Station preset buttons...............................196Station tuning control.................................195
Manual tuning......................................................195Scan tuning...........................................................195Seek tuning...........................................................195
Steering Wheel Lock.....................................84Steering Wheel...............................................36Storage compartments................................81Switching Off the Engine............................86
Vehicles with a turbocharger..........................86Symbols Glossary.............................................7
Symbols in this handbook...................................7Symbols on your vehicle.......................................7
System settings..............................................177Audio settings......................................................178Clock settings.......................................................178Menu structure - Information and
entertainment display - Allvehicles..............................................................178
Menu structure - Information andentertainment display - Vehicles withnavigation system..........................................177
TTailgate...............................................................111Technical Specifications
See: Capacities and Specifications.............163Telephone commands...............................222
Create a phonebook.........................................225Main settings.......................................................226Phone.....................................................................222Phone functions.................................................223
Telephone controls......................................210Remote control...................................................210
245
Index
Telephone setup..........................................208Bond another Bluetooth phone..................209Making a phone an active phone................208Phonebook..........................................................208Phonebook categories....................................208
Telephone......................................................208General Information.........................................208
TelephoneSee: Using the telephone................................210
Tow Ball............................................................1184x2.............................................................................1184x2 (vehicles with increased ride height)
and 4x4..............................................................119Driving without a trailer.....................................119Maintenance.........................................................119
Towing a Trailer..............................................116Steep gradients....................................................116Technical specifications....................................117Trailer tow module..............................................116
Towing Points.................................................134...................................................................................134
Towing the Vehicle on FourWheels...........................................................134All vehicles............................................................134Vehicles with automatic
transmission....................................................134Towing...............................................................116Track selection.............................................200
Type 2, 3, 4 and 5..............................................200Type 3, 4 and 5...................................................200
Traffic information control.......................196Activating traffic announcements...............196Ending traffic announcements......................197Traffic announcement volume......................197
Traffic Message Channel...........................182Principle of Operation.......................................182
Transmission....................................................92Trip Computer.................................................62
.....................................................................................62Controls...................................................................62
Type approvals.............................................235FCC/INDUSTRY CANADA NOTICE.............235RX-42 - declaration of conformity..............235
Tyre Care.........................................................160Alloy Wheels........................................................160Steel Wheels........................................................160
Tyre PressuresSee: Technical Specifications.........................161
TyresSee: Wheels and Tyres.....................................154
UUnder Bonnet Overview - 2.2L
Duratorq-TDCi (Puma) Diesel..............139Under Bonnet Overview - 2.5L
Duratec-HE (122kW/165PS) -MI4...................................................................137
Under Bonnet Overview - 3.2LDuratorq-TDCi (Puma) Diesel...............141
USB port............................................................82USB
See: Using a USB device..................................231Using an iPod.................................................233
Radio.......................................................................233SD Navigation units..........................................234
Using a USB device......................................231SD Navigation units...........................................232USB..........................................................................231
Using Cruise Control...................................109Cancelling the set speed..................................110Changing the set speed...................................109Resuming the set speed...................................110Setting a speed...................................................109Switching cruise control off............................110Switching cruise control on............................109
Using Hill Descent Control.........................98HDC operation......................................................98Selecting HDC.......................................................98
Using hill start assist...................................102Activating the system.......................................102Deactivating the system..................................103
Using seat belts during pregnancy..........25Using Snow Chains.......................................161Using Stability Control...............................100
2-wheel drive vehicles.......................................1014-wheel drive vehicles.......................................101
Using the Parking Aid - Vehicles With:Rear Parking Aid........................................104
Using the Rear View Camera...................107Activating the rear view camera...................107Deactivating the rear view camera.............108Using the display.................................................107
246
Index
Using the telephone....................................210Changing the active phone..............................211Debonding a bonded phone...........................212Making a call........................................................210Muting the microphone.....................................211Receiving an incoming call...............................211Receiving a second incoming call..................211
Using TMC.......................................................182Ending traffic announcements......................182Traffic announcement......................................182Using TMC messages.......................................182
Using voice control.......................................213Name tag...............................................................214System operation................................................213
Using Winter Tyres.......................................160
VVehicle battery...............................................152Vehicle Care....................................................150Vehicle Identification Number.................162Vehicle Identification Plate.......................162Vehicle identification...................................162Vehicle recovery............................................134Ventilation
See: Climate Control..........................................66Vents
See: Air Vents........................................................66VIN
See: Vehicle Identification Number.............162Voice control...................................................213
Principle of Operation.......................................213Voice Control....................................................37
WWarning Lamps and Indicators................56
ABS warning lamp...............................................56Airbag warning lamp...........................................57Brake system warning lamp.............................57Cruise control........................................................59Direction indicators.............................................59Door open warning lamp..................................59DPF (Diesel Particulate Filter)........................58Electronic locking differential (ELD)
indicator..............................................................58Engine warning lamps........................................58Four-wheel drive indicator...............................58Four-wheel drive low (4L) indicator ............58Front fog lamp indicator....................................59Gear shift indicator lamp (Manual
only).....................................................................59Glow plug indicator - For Diesel
vehicles...............................................................59Headlamp indicator............................................59Ice/Frost warning indicator..............................59Ignition warning lamp.........................................57Low fuel level warning lamp.............................57Main beam indicator...........................................59Oil Change Reminder Indicator (Diesel
only)......................................................................57Oil pressure warning lamp................................57Rear fog lamp indicator.....................................59Seat belt indicator...............................................59Stability control (ESP) indicator.....................57Vehicle immobiliser indicator...........................57Washer fluid level indicator..............................58Water-in-fuel indicator......................................58
Warning Triangle...........................................122Double cab............................................................123Single cab..............................................................122Stretch cab............................................................122
Washer Fluid Check.....................................146Washers
See: Wipers and Washers.................................38Washing
See: Cleaning the Exterior...............................150Waveband button........................................195Wheels and Tyres.........................................154
General Information..........................................154Technical Specifications...................................161
Windows and Mirrors....................................52
247
Index
Windscreen Washers....................................39Windscreen Wipers.......................................38
Intermittent wipe.................................................38Winter Tyres
See: Using Winter Tyres...................................160Wipers and Washers.....................................38
248
Index