2015 EROSION CONTROL TECHNICAL BULLETINS · 2016. 2. 25. · Thickness ASTM D6525 0.351 in Light...

2015 EROSION CONTROL

TECHNICAL BULLETINS

1600 Cornhusker Hwy~Lincoln, NE 68521 Phone: 402-438-1232 Fax: 402-438-1068

www.MillerSeed.com

http://www.MillerSeed.com

Miller Seed Company1600 Cornhusker HwyLincoln, NE 68521Phone (402) 438-1232Fax (402) 438-1068www.MillerSeed.com

ROLL SIZE NDOR CLASSEROSION CONTROL BLANKET

NORTH AMERICAN

GREEN

AMERICAN EXCELSIOR

8'x112' /16'x112' 1C S31 S75

8'x112' /16'x112' 1D S32 S150

8'x112' /16'x112' 1E SC32 SC150

8'x112' /16'x112' 1F C32 C125

8'x90' 1B Curlex Net Free

8'x 150' /16'x150' 1C Curlex I CL

8'x112' /16'x112' 1C Curlex I

8'x90' /16'x90' 1D, 1F Curlex II .98

8'x112' /16'x112' S31BD S75BN

8'x112' /16'x112' S32BD S150BN

8'x112' /16'x112' SC32BD SC150BN

8'x112' /16'x112' C32BD C125BN

8'x101'25' Curlex I

8'x101.25' Curlex IINatural Double Net Wood Excelsior .73 LB /SY

Shaded Items are Stocked by Miller Seed

Single Net Wood Excelsior .5 LB /SY

Single Net Wood Excelsior .73 LB /SY

Double Net Wood Excelsior .98 LB /SY

Single Net Straw

Double Net Straw

70% Straw 30% Coconut

EROSION CONTROL BLANKET COMPARISON

Rolled Erosion Control Blanket

Biodegradable Erosion Control Blanket

100% Coconut

Natural Single Net Wood Excelsior .73 LB /SY

DESCRIPTION

Single Net Straw

Double Net Straw

70% Straw 30% Coconut

100% Coconut

Wood Excelsior Net Free

http://www.millerseed.com/

Rev 0111

PHONE: (866) 317-3346 www.erosioncontrolblanket.com FAX: (204) 231-8134

S31 Specification Sheet

The ErosionControlBlanket S31 is a short-term straw fiber erosion control blanket designed for use on mild slope and channel applications requiring erosion control for up to 12 months depending on moisture, light, and environmental conditions. The blanket is sewn together on 1.5 inch (38.1 mm) centers. The S31 meets all requirements established in the FHWA FP-03 as a Type 2C erosion control blanket for use on slopes with gradients not exceeding 3:1 (h:v) and has been tested by the National Transportation Product Evaluation Program (NTPEP). The S31 comes packaged in clear shrink-wrap with a yellow band and includes installation instructions.

Product Nomenclature & Properties

S = 100% agricultural straw fiber matrix 3 = straw fiber matrix applied at a rate of 0.5 lbs/yd

2 (270 g/m

2)

1 = a single photodegradable top net with a mesh size of 0.588 x 0.5 in (1.49 x 1.3 cm) = photodegradable net and thread to ensure consistent functional longevity

Index & Bench Scale Testing

Test Description Test Method Test Results

Mass per Unit Area ASTM D6475 8.56 oz/yd2

Tensile Strength ASTM D6818 12.2 lbs/in @ 24.3% MD 3.9 lbs/in @ 25.6% TD

Thickness ASTM D6525 0.351 in

Light Penetration / Ground Cover ASTM D6567 11.7% / 88.3%

Water Absorption ASTM D 1117 &

ECTCTASC 00197 502%

Unvegetated Bench-Scale Rain Splash and Runoff (not to be used as a design value)

ASTM D7101 Soil Loss Ratio* = 8.57 Soil Loss Ratio* = 10.89 Soil Loss Ratio* = 13.83

Unvegetated Bench-Scale Shear Stress (not to be used as a design value)

ASTM D7207 1.5 lbs/ft2 @ ½ in. soil loss

Seed Germination and Plant Growth Under Bench-Scale Conditions

ASTM D7322 367% Improvement (increased biomass)

*Soil Loss Ratio = Soil Loss Bare Soil / Soil Loss with RECP = 1 / C-Factor (Note: Soil loss is based on regression analysis)

Design Values “C” factor = 0.03

Maximum Permissible Shear Stress = 1.5 lbs/ft2 (72 Pa)

Maximum Permissible Velocity = 5 ft./sec. (1.52 m/s)

Manning’s “n” = 0.027

Standard Roll Details Width 2.44m (8 ft) 4.88m (16 ft) Standard Length 34.3m (112.5 ft) 34.3m (112.5 ft) Area 83.61m

2 (100 yd

2) 167.23m

2 (200 yd

2)

Weight ±10% 24kg (52 lb) 48kg (104 lb)

“Big Daddy” Roll Details Width 2.44m (8 ft) 4.88m (16 ft) Standard Length 171.5m (562.5ft) 171.5m (562.5ft) Area 418m

2 (500 yd

2) 836.1m

2 (1000 yd

2)

Weight ±10% 117.93kg (260 lb) 235.87kg (520 lb)

Rev 0214

PHONE (866) 317-3346 www.erosioncontrolblanket.com FAX (204) 231-8134

S31 UVD

Specification Sheet The ErosionControlBlanket S31 UVD is an ultra short-term straw fiber erosion control blanket designed for use on mild slope and channel applications requiring erosion control for up to 3 months depending on moisture, light, and environmental conditions. The blanket is sewn together on 1.5 inch (38.1 mm) centers. The S31 UVD meets all requirements established in the FHWA FP-03 as a Type 1C erosion control blanket for use on slopes with gradients not exceeding 3:1 (h:v) and has been tested by the National Transportation Product Evaluation Program (NTPEP). The S31 UVD comes packaged in clear shrink-wrap with a red band and includes installation instructions.



2 (270 g/m

2)

1 = a single rapid photodegradable top net with a mesh size of 0.588 x 0.5 in (1.49 x 1.3 cm) UVD = rapid photodegradable net and thread to ensure consistent functional longevity

Index & Bench Scale Testing Test Description Test Method Test Results






ECTCTASC 00197 490%













2 (100 yd

2) 167.23m

2 (200 yd

2)

Weight ±10% 24kg (52 lb) 48kg (104 lb)

“Big Daddy” Roll Details Width 2.44m (8 ft) 4.88m (16 ft) Standard Length 171.49m (562.5ft) 171.49m (562.5ft) Area 418m

2 (500 yd

2) 836m

2 (1000 yd

2)

Weight ±10% 117.94kg (260 lb) 235.87kg (520 lb)

Rev 0111

PHONE: (866) 317-3346 • www.erosioncontrolblanket.com • FAX: (204) 231-8134

S32 Specification Sheet

The ErosionControlBlanket S32 is a short-term double net straw fiber erosion control blanket designed for use on moderate slope and channel applications requiring erosion control for up to 12 months depending on moisture, light, and environmental conditions. The blanket is sewn together on 1.5 inch (38.1 mm) centers. The S32 meets all requirements established in the FHWA FP-03 as a Type 2D erosion control blanket for use on slopes with gradients not exceeding 2:1 (h:v) and has been tested by the National Transportation Product Evaluation Program (NTPEP). The S32 comes packaged in clear shrink-wrap with a green band and includes installation instructions. Product Nomenclature & Properties

S = 100% agricultural straw fiber matrix 3 = straw fiber matrix applied at a rate of 0.5 lbs/yd2 (270 g/m2) 2 = top and bottom photodegradable nets with a mesh size of 0.588 x 0.5 in (1.49 x 1.3 cm) = photodegradable nets and thread to ensure consistent functional longevity


Test Description Test Method Test Results Mass per Unit Area ASTM D6475 9.43 oz/yd2

Tensile Strength ASTM D6818 11.4 lbs/in @ 22.3% MD10.1 lbs/in @ 20.3% TD

Thickness ASTM D6525 0.432 in Light Penetration / Ground Cover ASTM D6567 6.2% / 93.6%

Water Absorption ASTM D 1117 & ECTCTASC 00197 531%

Unvegetated Bench-Scale Rain Splash and Runoff (not to be used as a design value) ASTM D7101

Soil Loss Ratio* = 13.13 Soil Loss Ratio* = 16.77 Soil Loss Ratio* = 21.41

Unvegetated Bench-Scale Shear Stress (not to be used as design value) ASTM D7207 1.64 lbs/ft2 @ ½ in. soil loss

Seed Germination and Plant Growth Under Bench-Scale Conditions ASTM D7322 441% Improvement

(increased biomass) *Soil Loss Ratio = Soil Loss Bare Soil / Soil Loss with RECP = 1 / C-Factor (Note: Soil loss is based on regression analysis)

Design Values

• “C” factor = 0.005 • Maximum Permissible Shear Stress = 1.75 lbs/ft2 (84 Pa) • Maximum Permissible Velocity = 6 ft./sec. (1.83 m/s) • Manning’s “n” = 0.03

Standard Roll Details Width 2.44m (8 ft) 4.88m (16 ft) Standard Length 34.3m (112.5 ft) 34.3m (112.5 ft) Area 83.61m2 (100 yd2) 167.23m2 (200 yd2) Weight ±10% 25kg (54 lb) 50kg (108 lb) “Big Daddy” Roll Details Width 2.44m (8 ft) 4.88m (16 ft) Standard Length 137.2m (450 ft) 137.2m (450 ft) Area 334.4m2 (400 yd2) 668.8m2 (800 yd2) Weight ±10% 100kg (216 lb) 200kg (432 lb)

Rev 0214


S32 UVD

Specification Sheet The ErosionControlBlanket S32 UVD is an ultra short-term double net straw fiber erosion control blanket designed for use on moderate slope and channel applications requiring erosion control for up to 3 months depending on moisture, light, and environmental conditions. The blanket is sewn together on 1.5 inch (38.1 mm) centers. The S32 UVD meets all requirements established in the FHWA FP-03 as a Type 1D erosion control blanket for use on slopes with gradients not exceeding 2:1 (h:v) and has been tested by the National Transportation Product Evaluation Program (NTPEP). The S32 UVD comes packaged in clear shrink-wrap with a blue band and includes installation instructions.



2 (270 g/m

2)

2 = top and bottom rapid photodegradable nets with a mesh size of 0.588 x 0.5 in (1.49 x 1.3 cm) UVD = rapid photodegradable nets and thread to ensure consistent functional longevity







ECTCTASC 00197 496%









Maximum Permissible Shear Stress = 84 Pa (1.75 lbs/ft2)




2 (100 yd

2) 167.23m

2 (200 yd

2)

Weight ±10% 25kg (54 lb) 50kg (108 lb)

“Big Daddy” Roll Details Width 2.44m (8 ft) 4.88m (16 ft) Standard Length 171.49m (562.5 ft) 171.49m (562.5 ft) Area 418m

2 (500 yd

2) 836m

2 (1000 yd

2)

Weight ±10% 122.5kg (270 lb) 244.94kg (540 lb)

Rev 0111


SC32

Specification Sheet The ErosionControlBlanket SC32 is an extended-term double net straw/coconut fiber erosion control blanket designed for use on severe slope and channel applications requiring erosion control for up to 24 months depending on moisture, light, and environmental conditions. The blanket is sewn together on 1.5 inch (38.1 mm) centers. The SC32 meets all requirements established in the FHWA FP-03 as a Type 3B erosion control blanket for use on slopes with gradients not exceeding 1.5:1 (h:v) and has been tested by the National Transportation Product Evaluation Program (NTPEP). The SC32 comes packaged in clear shrink-wrap with a tan band and includes installation instructions.


SC = 70% agricultural straw and 30% coconut fiber matrix 3 = straw/coconut fiber matrix applied at a rate of 0.5 lbs/yd

2 (270 g/m

2)

2 = top UV stabilized photodegradable black net with a mesh size of 0.626 x 0.626 in (1.59 x 1.59 cm) = bottom photodegradable net with a mesh size of 0.588 x 0.5 in (1.49 x 1.3 cm)

= UV stabilized photodegradable thread to ensure consistent functional longevity



Tensile Strength ASTM D6818 21.2 lb/in @ 20.5% MD 8.4 lb/in @ 21.2% TD


Light Penetration / Ground Cover ASTM D6567 6% / 94%


ECTCTASC 00197 398%










Maximum Permissible Velocity = 8 ft/sec (2.44 m/s)



2 (100 yd

2) 167.23m

2 (200 yd

2)

Weight ±10% 25kg (54lb) 50kg (108lb)

“Big Daddy” Roll Details Width 2.44m (8 ft) 4.88m (16 ft) Standard Length 171.5m (562.5 ft) 171.5m (562.5 ft) Area 418m

2 (500 yd

2) 836.1m

2 (1000 yd

2)

Weight ±10% 125kg (270lb) 250kg (540lb)

Rev 0514


C32 Specification Sheet

The ErosionControlBlanket C32 is a long-term double net 100% coconut fiber erosion control blanket designed for use on extreme slope and channel applications requiring erosion control for up to 36 months depending on moisture, light, and environmental conditions. The blanket is sewn together on 1.5 inch (38.1 mm) centers. The C32 meets all requirements established in the FHWA FP-03 as a Type 4 erosion control blanket for use on slopes with gradients not exceeding 1:1 (h:v) and has been tested by the National Transportation Product Evaluation Program (NTPEP). The C32 comes packaged in clear shrink-wrap and includes installation instructions. Product Nomenclature & Properties

C = 100% coconut fiber matrix 3 = coconut fiber matrix applied at a rate of 0.5 lbs/yd2 (270 g/m2) 2 = top & bottom stabilized photodegradable black net with a mesh size of 0.626 x 0.626 in (1.59 x 1.59 cm) = UV stabilized photodegradable thread to ensure consistent functional longevity







Soil Loss Ratio* = 13.54 Soil Loss Ratio*= 18.69 Soil Loss Ratio*= 25.80

Unvegetated Bench-Scale Shear Stress (not to be used as a design value) ASTM D7207 2.75 lbs/ft2 @ ½ in. soil loss



Design Values

• “C” factor = 0.002 • Maximum Permissible Shear Stress = 2.25 lbs/ft2 (108 Pa) • Maximum Permissible Velocity = 10 ft/sec (3.05 m/s) • Manning’s “n” = 0.03

Standard Roll Details Width 2.44m (8ft) 4.88m (16ft) Standard Length 34.3m (112.5ft) 34.3m (112.5ft) Area 83.61m2 (100yd2) 167.2m2 (200yd2)

Weight ±10% 26.3kg (58lb) 51.7kg (114lb) “Big Daddy” Roll Details Width 2.44m (8ft) 4.88m (16ft) Standard Length 171.5m (562.5ft) 171.5m (562.5ft) Area 418m2 (500yd2) 836.1m2 (1000yd2)

Weight ±10% 127kg (279lb) 254kg (558lb)

MATERIAL SPECIFICATIONS

CURLEX® I CL Materials:

Great Lakes Aspen (naturally seed free) Polypropylene Netting Stitching Thread QuickGRASS® (green excelsior – optional) Typical Roll Sizes:

Width: 4.0 ft (1.2 m) 8.0 ft (2.4 m) 16.0 ft (4.9 m) Length: 150.0 ft (45.7 m) 150.0 ft (45.7 m) 150.0 ft (45.7 m) Area: 66.7 yd2 (55.7 m2) 133.3 yd2 (111.5 m2) 266.7 yd2 (223.0 m2) Weight: 36.7 lb (16.6 kg) 73.3 lb (33.3 kg) 146.7 lb (66.5 kg)

Description:

Curlex I CL erosion control blanket (ECB) is a natural, stitched excelsior blanket that provides a temporary organic cover to reduce erosion, protect seeds, enhance germination, and hasten re-vegetation. Curlex I CL is furnished in rolls with polyethylene wrapping to protect against the elements prior to installation, and may be ordered in Master-Paks of fifteen rolls banded together to minimize material handling requirements. Curlex I CL is also available as QuickGRASS (Dyed Green). Curlex I CL shall be manufactured in the U.S.A. Curlex I CL has a design soil loss ratio (event-based RUSLE C factor) of .039 and is typically suitable for slopes up to 2.5H:1V. Curlex I CL is rated for channel flows up to 5.0 ft/s (1.5 m/s) and 1.60 lb/ft2 (77 Pa) shear stress.

Physical Properties: Fiber: Great Lakes Aspen (naturally seed free) Curled, interlocking fibers with barbed edges Fiber Size: 80% of fibers a minimum of 6 in (15.2 cm) long 0.038 in ± 0.008 in wide x 0.018 in ± 0.003 in thick (0.97 mm ± 0.20 mm wide x 0.46 mm ± 0.08 mm thick)

Weight1: 0.55 lb/yd2 (0.30 kg/m2) ± 10% @ 22% Moisture Thread Pattern: No more than 4.0 in (10.2 cm) transverse stitch spacing Net Material: Polypropylene (green with oxo-biodegrader and UV degrader

additives or white with UV degrader additive) Net Openings: 1.0 in wide x 2.0 in long (25.4 mm wide x 50.8 mm long) Net Configuration: Top side only

1 Weight is based on a dry fiber weight basis at time of manufacture. Baseline moisture content of Great Lakes Aspen excelsior is 22%.

850 Avenue H East | Arlington, Texas 76011 Phone 1-800-777-SOIL | Fax 817-385-3585 | www.Curlex.com

W0115R0315

http://www.curlex.com/


CURLEX® II (.98) Materials:

Great Lakes Aspen (naturally seed free) Polypropylene Netting Stitching Thread QuickGRASS® (green excelsior – optional) Typical Roll Sizes:

Width: 4.0 ft (1.2 m) 8.0 ft (2.4 m) 16.0 ft (4.9 m) Length: 90.0 ft (27.4 m) 90.0 ft (27.4 m) 90.0 ft (27.4 m) Area: 40.0 yd2 (33.4 m2) 80.0 yd2 (66.9 m2) 160.0 yd2 (133.8 m2) Weight: 39.2 lb (17.8 kg) 78.4 lb (35.6 kg) 156.8 lb (71.2 kg)

Description:

Curlex II .98 erosion control blanket (ECB) is a natural, stitched excelsior blanket that provides a temporary organic cover to reduce erosion, protect seeds, enhance germination, and hasten re-vegetation. Curlex II .98 is furnished in rolls with polyethylene wrapping to protect against the elements prior to installation, and may be ordered in Master-Paks of fifteen rolls banded together to minimize material handling requirements. Curlex II .98 is also available as QuickGRASS (Dyed Green). Curlex II .98 shall be manufactured in the U.S.A. Curlex II .98 has a design soil loss ratio (event-based RUSLE C factor) of .022 and is typically suitable for slopes up to 1H:1V. Curlex II .98 is rated for channel flows up to 10.0 ft/s (3.1 m/s) and 2.5 lb/ft2 (120 Pa) shear stress.


Weight1: 0.98 lb/yd2 (0.53 kg/m2) ± 10% @ 22% Moisture Thread Pattern: No more than 4.0 in (10.2 cm) transverse stitch spacing Net Material: Polypropylene (green with oxo-biodegrader and UV degrader

additives or white with UV degrader additive) Net Openings: 1.0 in wide x 2.0 in long (25.4 mm wide x 50.8 mm long) Net Configuration: Top and bottom

1 Weight is based on a dry fiber weight basis at time of manufacture. Baseline moisture content of Great Lakes Aspen excelsior is 22%

850 Avenue H East | Arlington, Texas 76011

Phone 1-800-777-SOIL | Fax 817-385-3585 | www.Curlex.com W0114R0315



CURLEX® III Materials:

Great Lakes Aspen (naturally seed free) Polypropylene Black Netting Stitching Thread QuickGRASS® (green excelsior – optional) Typical Roll Sizes:

Width: 4.0 ft (1.2 m) 8.0 ft (2.4 m) 16.0 ft (4.9 m) Length: 90.0 ft (27.4 m) 90.0 ft (27.4 m) 90.0 ft (27.4 m) Area: 40.0 yd2 (33.4 m2) 80.0 yd2 (66.9 m2) 160.0 yd² (133.8 m²) Weight: 39.2 lb (17.8 kg) 78.4 lb (35.6 kg) 156.8 lb (71.2 kg)

Description:

Curlex III erosion control blanket (ECB) is a natural, stitched excelsior blanket that provides a temporary organic cover to reduce erosion, protect seeds, enhance germination, and hasten re-vegetation. Curlex III is furnished in rolls with polyethylene wrapping to protect against the elements prior to installation, and may be ordered in Master-Paks of fifteen rolls banded together to minimize material handling requirements. Curlex III is also available as QuickGRASS (Dyed Green). Curlex III shall be manufactured in the U.S.A. Curlex III has a design soil loss ratio (event-based RUSLE C factor) of .022 and is typically suitable for slopes up to 1H:1V. Curlex III is rated for channel flows up to 10.0 ft/s (3.1 m/s) and 2.5 lb/ft2 (120 Pa) shear stress.


Weight1: 0.98 lb/yd2 (0.53 kg/m2) ± 10% @ 22% Moisture Thread Pattern: No more than 4.0 in (10.2 cm) transverse stitch spacing Net Material: Polypropylene (black with oxo-biodegrader and UV degrader

additives) Net Openings: 1.0 in wide x 2.0 in long (25.4 mm wide x 50.8 mm long)

Net Configuration: Top and bottom 1 Weight is based on a dry fiber weight basis at time of manufacture. Baseline moisture content of Great Lakes Aspen excelsior is 22%.


W0114R0315


Rev 0911


S31 BD Specification Sheet

The ErosionControlBlanket S31 BD is a short-term 100% biodegradable straw fiber erosion control blanket designed for use on mild slope and channel applications requiring erosion control for up to 12 months depending on moisture, light, and environmental conditions. The blanket is sewn together on 1.5 inch (38.1 mm) centers. The S31 BD meets all requirements established in the FHWA FP-03 as a Type 2C erosion control blanket for use on slopes with gradients not exceeding 3:1 (h:v) and has been tested by the National Transportation Product Evaluation Program (NTPEP). The S31 BD comes packaged in clear shrink-wrap with an orange band and includes installation instructions.



2 (270 g/m

2)

1 = a single biodegradable leno woven top net with a mesh size of 0.5 x 1.0 in (1.3 x 2.54 cm) BD = 100% biodegradable leno woven net, thread, and matrix to ensure consistent functional longevity







ECTCTASC 00197 417%












Standard Roll Details

Width 2.44m (8 ft) 4.88m (16 ft) Standard Length 34.3m (112.5 ft) 34.3m (112.5 ft) Area 83.61m

2 (100 yd

2) 167.22m

2 (200 yd

2)

Weight ± 10% 27.2 kg (60 lb) 54.4 kg (120 lb)

“Big Daddy” Roll Details Width 2.44m (8 ft) 4.88m (16 ft) Standard Length 120m (393.75ft) 120m (393.75 ft) Area 292.65m

2 (350yd

2) 585.3m

2 (700 yd

2)

Weight ± 10% 95.26kg (210 lb) 190.51kg (420 lb)

Rev 1011


S32 BD Specification Sheet

The ErosionControlBlanket S32 BD is a short-term 100% biodegradable double net straw fiber erosion control blanket designed for use on moderate slope and channel applications requiring erosion control for up to 12 months depending on moisture, light, and environmental conditions. The blanket is sewn together on 1.5 inch (38.1 mm) centers. The S32 BD meets all requirements established in the FHWA FP-03 as a Type 2D erosion control blanket for use on slopes with gradients not exceeding 2:1 (h:v) and has been tested by the National Transportation Product Evaluation Program (NTPEP). The S32 BD comes packaged in clear shrink-wrap with a brown band and includes installation instructions.



2 (270 g/m

2)

2 = top and bottom leno woven biodegradable nets with a mesh size of 0.5 x 1.0 in (1.3 x 2.54 cm) BD = 100% biodegradable leno woven net, thread, and matrix to ensure consistent functional longevity







ECTCTASC 00197 416%













2 (100 yd

2) 167.22m

2 (200 yd

2)

Weight ± 10% 30.8 kg (68 lb) 61.6 kg (136 lb)

“Big Daddy” Roll Details

Width 2.44m (8 ft) 4.88m (16 ft) Standard Length 120m (393.75ft) 120m (393.75ft) Area 292.6m

2 (350 yd

2) 585.3m

2 (700 yd

2)

Weight ± 10% 108kg (238 lb) 215.9kg (476 lb)

Rev 0911


SC32 BD Specification Sheet

The ErosionControlBlanket SC32 BD is an extended-term 100% biodegradable double net straw/coconut fiber erosion control blanket designed for use on severe slope and channel applications requiring erosion control for up to 24 months depending on moisture, light, and environmental conditions. The blanket is sewn together on 1.5 inch (38.1 mm) centers. The SC32 BD meets all requirements established in the FHWA FP-03 as a Type 3B erosion control blanket for use on slopes with gradients not exceeding 1.5:1 (h:v) and has been tested by the National Transportation Product Evaluation Program (NTPEP). The SC32 BD comes packaged in green shrink-wrap with a brown band and includes installation instructions. Product Nomenclature & Properties

SC = 70% agricultural straw and 30% coconut fiber matrix 3 = straw/coconut fiber matrix applied at a rate of 0.5 lbs/yd2 (270 g/m2) 2 = top and bottom leno woven biodegradable nets with a mesh size of 0.5 x 1.0 in (1.3 x 2.54 cm) BD = 100% biodegradable leno woven net, thread, and matrix to ensure consistent functional longevity







Soil Loss Ratio* = 14.01 Soil Loss Ratio* = 16.06 Soil Loss Ratio* = 18.40




Design Values

• “C” factor = 0.002 • Maximum Permissible Shear Stress = 2.00 lbs/ft2 (96 Pa) • Maximum Permissible Velocity = 8 ft/sec (2.44 m/s) • Manning’s “n” = 0.03

Standard Roll Details Width 2.44m (8 ft) 4.88m (16 ft) Standard Length 34.3m (112.5 ft) 34.3m (112.5 ft) Area 83.61m2 (100 yd2) 167.22m2 (200 yd2) Weight ± 10% 30.8 kg (68 lb) 61.6 kg (136 lb) “Big Daddy” Roll Details Width 2.44m (8 ft) 4.88m (16 ft) Standard Length 102.8m (337.5 ft) 102.8m (337.5 ft) Area 250.8m2 (300 yd2) 501.6m2 (600 yd2) Weight ± 10% 92.5 kg (204 lb) 185 kg (408 lb)

Rev 0111


C32 BD

Specification Sheet The ErosionControlBlanket C32 BD is a long-term 100% biodegradable double net 100% coconut fiber erosion control blanket designed for use on extreme slope and channel applications requiring erosion control for up to 36 months depending on moisture, light, and environmental conditions. The blanket is sewn together on 1.5 inch (38.1 mm) centers. The C32 BD meets all requirements established in the FHWA FP-03 as a Type 4 erosion control blanket for use on slopes with gradients not exceeding 1:1 (h:v) and has been tested by the National Transportation Product Evaluation Program (NTPEP). The C32 BD comes packaged in clear shrink-wrap with a purple band and includes installation instructions.


C = 100% coconut fiber matrix 3 = coconut fiber matrix applied at a rate of 0.5 lbs/yd

2 (270 g/m

2)

2 = top and bottom leno woven biodegradable nets with a mesh size of 0.5 x 1.0 in (1.3 x 2.54 cm) BD = 100% biodegradable leno woven net, thread, and matrix to ensure consistent functional longevity







ECTCTASC 00197 271%










Maximum Permissible Velocity = 10 ft/sec (3.05 m/s)



2 (100 yd

2) 167.22m

2 (200 yd

2)

Weight ± 10% 30.8 kg (68 lb) 61.6 kg (136 lb)

“Big Daddy” Roll Details Width 2.44m (8 ft) 4.88m (16 ft) Standard Length 137.2m (450ft) 137.2m (450ft) Area 334.5m

2 (400 yd

2) 669m

2 (800 yd

2)

Weight ± 10% 92.5 kg (272 lb) 246.76kg (544lb)

Rev 0508


Specification Sheet

9-Inch STENLOG (Straw Wattle)

The 9-inch (23 cm) Stenlog (Straw Wattle) is an elongated tube of compacted straw

and/or other fibers wrapped in UV stabilized degradable tubular polypropylene plastic netting. The 9-inch (23 cm) Stenlog is used for temporary erosion and sediment control applications and are commonly installed along the contours or at the base of a slope to help reduce soil erosion and retain sediment. The Stenlog is designed to allow runoff/water to penetrate through the fiber while reducing sediment migration. Stenlogs function as slope interruption devices and therefore shorten slope lengths reducing runoff velocity and the potential for sheet erosion and rill formation. Stenlogs work in conjunction with surface roughening, straw mulching, bonded fiber matrix, hydroseeding and erosion control blankets to further reduce erosion and sediment migration.

• The Stenlog provides a cost effective alternative to other sediment trapping devices.

• The Stenlog can be easily installed and removed.

• The straw matrix of the 9-inch Stenlog is biodegradable

• The functional longevity is approximately 6-18 months, depending on moisture, light, and environmental conditions.

Stenlog 9-inch Property Test Method

Metric Imperial

Mass/Unit Length Field Measure 3.29 kg/m ± 10% 2.2 lbs/ft ± 10%

Diameter Field Measure 20-23 cm 8-9 in

Length Field Measure 7.6 m 25 ft

Net Strand Thickness

Field Measure 0.041 cm 0.0165 in

Netting Weight Certified 25 g/m 0.81 oz/yd

Installed Free- Board Height

Field Measure 14-16.5 cm 5.5-6.5 in

Mesh Opening Certified 1.27 cm 0.5 in

Stretch Width Certified 31.75 cm 12.5 in

More information available upon request.

Specification Sheet

12-Inch STENLOG

(Straw Wattle)

The 12-inch (30.5 cm) Stenlog (Straw Wattle) is an elongated tube of compacted straw

and/or other fibers wrapped in UV stabilized degradable tubular polypropylene plastic netting. The 12-inch (30.5 cm) Stenlog is used for temporary erosion and sediment control applications and are commonly installed along the contours or at the base of a slope to help reduce soil erosion and retain sediment. The Stenlog is designed to allow runoff/water to penetrate through the fiber while reducing sediment migration. Stenlogs function as slope interruption devices and therefore shorten slope lengths reducing runoff velocity and the potential for sheet erosion and rill formation. Stenlogs work in conjunction with surface roughening, straw mulching, bonded fiber matrix, hydroseeding and erosion control blankets to further reduce erosion and sediment migration.

• The Stenlog provides a cost effective alternative to other sediment trapping

devices.

• The Stenlog can be easily installed and removed.

• The functional longevity is approximately 6-24 months, depending on moisture, light, and environmental conditions.

Rev 0314

Property

Test Method

Stenlog 12-inch

Metric

Imperial

Mass/Unit Length

Field Measure

5.24 kg/m ± 10%

3.5 lbs/ft ± 10%

Diameter

Field Measure

26.7-30.5 cm

10.5-12 in

Length

Field Measure

3M or 6M

10ft or 20ft

Net Strand Thickness

Field Measure

0.04 cm

0.016 in

Netting Weight

Certified

37.5 g/m

1.21 oz/yd

Installed Free- Board Height

Field Measure

20.3-22.9 cm

8-9 in

Mesh Opening

Certified

1.27 cm

0.5 in

Stretch Width

Certified

53.3 cm

21 in

More information available upon request.


http://www.erosioncontrolblanket.com/

MATERIAL SPECIFICATIONS CURLEX® SEDIMENT LOGS®

Materials: Great Lakes Aspen (naturally seed free) Durable Tubular Netting with Knotted Ends Typical Log Sizes:

Product

Name/Nominal Diameter

6.0 in 9.0 in 12.0 in 20.0 in

Minimum Diameter

5.5 in (14.0 cm)

8.0 in (20.3 cm)

11.0 in (27.9 cm)

18.0 in (45.7 cm)

Length (± 10%)

25.0 ft (7.6 m)

25.0 ft (7.6 m)

10.0 ft (3.1 m)

10.0 ft (3.1 m)

Weight1 (± 10%)

12.0 lb (5.4 kg)

25.0 lb (11.3 kg)

20.0 lb (9.1 kg)

30.0 lb (13.6 kg)

Density1 (± 10%)

2.44 lb/ft3 (39.15 kg/m3)

2.26 lb/ft3 (36.26 kg/m3)

2.54 lb/ft3 (40.80 kg/m3)

1.38 lb/ft3 (22.00 kg/m3)

Description:

Curlex Sediment Logs are designed to provide intimate contact with the soil, which prevents undermining and blowouts. Curlex Sediment Logs are porous. This property allows water to pass through the 100% excelsior matrix, which slows velocity and filters sediment as it passes through the log diameter. Curlex Sediment Logs may be installed over bare soil, over rolled erosion control products, on steep slopes, around inlets and outlets, or around jobsites for perimeter control. Curlex Sediment Logs are available palletized or master packed to minimize material handling requirements. Custom diameters, lengths, and densities are optional based upon material availability and sample approval. Curlex Sediment Logs shall be manufactured in the U.S.A. at company locations where QA/QC is implemented and managed by the manufacturer. Field fabricated products and products made by anyone other than the manufacturer (i.e. distributors, dealers, etc.) shall not be accepted.

Note: Curlex Sediment Logs may be compressed when packaged. The unique packaging can result in a less than symmetrical shape upon arrival to the jobsite. This will not affect the performance capability of Curlex Sediment Logs because unique Curlex fibers naturally expand upon wetting and return to a symmetrical tubular shape. All measurements are nominal.

Physical Properties:

Fiber: Great Lakes Aspen (naturally seed free) Curled, interlocking fibers with barbed edges Fiber Size: 80% of fibers a minimum of 6 in (15.2 cm) long 0.031 in ± 0.008 in wide x 0.027 in ± 0.006 in thick (0.79 mm ± 0.20 mm wide x 0.53 mm ± 0.15 mm thick)

Net Configuration: Totally encased

1 Weight and density are based on a dry fiber weight basis at time of manufacture. Baseline moisture content of Great Lakes Aspen excelsior is 22%.


W0314R0315


Rev 1007

Specification Sheet

PS42 The PS42 turf reinforcement matting from ErosionControlBlanket.com is manufactured from a composition of 67% polypropylene fiber and 33% agricultural straw stitched between a black UV stabilized polypropylene top net with a mesh size of 1.34 x 1.27 cm (0.53 x 0.5 in) and a black UV stabilized polypropylene bottom net with a mesh size of 1.59 x 1.59 cm (0.626 x 0.626 in). The “PS” and “4” represent the polypropylene and straw fiber applied at a minimum of 400 g/m

2 (0.75 lbs/yd

2) and the “2” represents that the mat is netted on the top and bottom sides.

The PS42 is a permanent turf reinforcement mat. The mat is sewn together on 38.1 mm (1.5 in) centers, with UV Stabilized polypropylene black thread. Each roll of PS42 is packaged in clear shrink-wrap with a teal band and includes installation instructions.

Index Test Results From Bench Scale Testing (TRI Environmental Labs or NTPEP)

Test Method – Description Parameters Test Result

ASTM D6566 – Mass per Unit Area Index Test 18.42 oz/sq. yd.

ASTM D4355 – UV Stability Index Test 90% at 500 hours

ASTM D6818 – Tensile Strength Machine Direction (MD) Transverse/Cross Direction (TD)

Index Test Index Test

24.8 lb/in @ 24.6% 11.2 lb/in @ 29.4%

ASTM D6525 – Thickness Index Test 0.711 in

ASTM D6567 – Ground Cover/Light Penetration Index Test 87.2%/12.8%

ECTC Method 3 – Determination of Unvegetated RECP Ability to Protect Soil from Hydraulically-Induced Shear

Stresses Under Bench-Scale Conditions - ASTM D7207

Regression (power curve) 3.2 psf @ ½ in soil loss

Standard Roll Details Width Standard Length

2.44m (8ft) 25.7m (84.3ft)

4.88m (16ft) 25.7m (84.3ft)

Area 62.7m2

(75yd2) 125.4m

2 (150yd

2)

Weight ±10% 28kg (61lb) 56kg (122lb) “Big Daddy” Roll Details

Width 2.44m (8ft) 4.88m (16ft)

Standard Length Area

102.8m (337.5ft)

250.8m2 (300yd

2)

102.8m (337.5ft)

500m2

(600yd2)

Weight ±10% 112kg (244 lb) 224kg (488 lb) More information available upon request.




CURLEX® ENFORCER® Materials:

Great Lakes Aspen (naturally seed free) Polypropylene Extra Heavy Duty Black Netting Stitching Thread QuickGRASS® (green excelsior – optional) Typical Roll Sizes:

Width: 8.0 ft (2.4 m) Length: 67.5 ft (20.6 m) Area: 60.0 yd2 (50.2 m2) Weight: 75.0 lb (34.1 kg)

Description:

Curlex Enforcer a biocomposite Turf Reinforcement Mat (TRM) is a natural, stitched cover material designed to enhance germination, reduce slope and/or channel erosion, and permanently reinforce vegetation. Curlex Enforcer is furnished in rolls with polyethylene wrapping to protect against the elements prior to installation, and may be ordered in Master-Paks of fifteen rolls banded together to minimize material handling requirements. Curlex Enforcer is also available as QuickGRASS (Dyed Green). Curlex Enforcer shall be manufactured in the U.S.A. Curlex Enforcer has a design soil loss ratio (event-based RUSLE C factor) of .022 and is typically suitable for slopes up to .5H:1V. Curlex Enforcer is rated for channel flows up to 11 ft/s (3.4 m/s); 3.25 lb/ft2 (156 Pa) shear stress unvegetated or 17 ft/s (5.2 m/s); 10.0 lb/ft2 (480 Pa) shear stress vegetated.


Weight1: 1.25 lb/yd2 (0.68 kg/m2) ± 10% @ 22% Moisture Thread Pattern: No more than 4.0 in (10.2 cm) transverse stitch spacing Net Material: Polypropylene extra heavy duty black Net Openings: 0.75 in wide x 1.0 in long (19.1 mm x 25.4 mm) Net Configuration: Top and bottom

1 Weight is based on a dry fiber weight basis at time of manufacture. Baseline moisture content of Great Lakes Aspen excelsior is 22%.


W0114R0315


Rev 1007

Specification Sheet

PC42 The PC42 turf reinforcement matting from ErosionControlBlanket.com is manufactured from a composition of 67% polypropylene fiber and 33% coconut fiber stitched between a black UV stabilized polypropylene top net with a mesh size of 1.34 x 1.27 cm (0.53 x 0.5 in) and a black UV stabilized polypropylene bottom net with a mesh size of 1.59 x 1.59 cm (0.626 x 0.626 in). The “PC” and “4” represent the polypropylene and coconut fiber applied at a minimum of 400 g/m

2 (0.75 lbs/yd

2) and the “2” represents that the mat is netted on the top and bottom sides.

The PC42 is a permanent turf reinforcement mat. The mat is sewn together on 38.1 mm (1.5 in) centers, with UV stabilized polypropylene black thread. Each roll of PC42 is packaged in clear shrink-wrap with a blue band and includes installation instructions.

Index Test Results From Bench Scale Testing (TRI Environmental Labs or NTPEP)

Test Method – Description Parameters Test Result

ASTM D6566 – Mass per Unit Area Index Test 10.8 oz/sq. yd.

ASTM D4355 – UV Stability Index Test 86% at 500 hours

ASTM D6818 – Tensile Strength Machine Direction (MD) Transverse/Cross Direction (TD)

Index Test Index Test

27.3 lb/in @ 38.6% 15.7 lb/in @ 27.4%

ASTM D6525 – Thickness Index Test 0.390 in

ASTM D6567 – Ground Cover/Light Penetration Index Test 79.7%/20.3%

ECTC Method 3 – Determination of Unvegetated RECP Ability to Protect Soil from Hydraulically-Induced Shear

Stresses Under Bench-Scale Conditions - ASTM D7207

Regression (power curve) 3.3 psf @ ½ in soil loss

Standard Roll Details

Width 2.44m (8ft) 4.88m (16ft) Standard Length Area

25.7m (84.3ft)

62.7m2

(75yd2)

25.7m (84.3ft)

125.4m2 (150yd

2)

Weight ±10% 28kg (61lb) 56kg (122lb)

“Big Daddy” Roll Details – Please contact ECB.Com for Confirmation of Roll Sizes Width 2.44m (8ft) 4.88m (16ft)

Standard Length Area

102.8m (337.5ft)

250.8m2 (300yd

2)

102.8m (337.5ft)

500m2

(600yd2)

Weight ±10% 112kg (244 lb) 224kg (488 lb) More information available upon request.




RECYCLEX® TRM Materials:

100% Recycled Post Consumer Polyester Fiber Polypropylene Netting Stitching Thread

Roll Sizes:

Width: 8.0 ft (2.4 m) 16.0 ft (4.9 m) Length: 90.0 ft (27.4 m) 90.0 ft (27.4 m) Area: 80.0 yd2 (66.9 m2) 160.0 yd2 (133.8 m2) Weight: 50.0 lb (22.7 kg) 100.0 lb (45.4 kg)

Description:

Recyclex TRM is a three dimensional Turf Reinforcement Mat (TRM) specifically designed to provide permanent structural support for vegetation root systems (root reinforcement) and/or surface support underneath vegetation (stem reinforcement). Recyclex TRM may be installed, soil filled, and seeded to allow the germination of reinforced vegetation above, and a permanent, structural root system to grow into its matrix below. In addition, Recyclex TRM may be installed as “stand alone” over top soil, seed, and fertilizer which allows vegetation to grow up through its permanent matrix. Recyclex TRM rolls are stretch wrapped to protect against the elements prior to installation, and may be ordered in Master-Paks of twenty and twenty-five rolls banded together to a pallet to minimize handling requirements. Recyclex TRM shall be manufactured in the U.S.A. and the fibers shall be made from 100% recycled post-consumer goods. Recyclex TRM has a design soil loss ratio (event-based RUSLE C factor) of .022 and is typically suitable for slopes up to .5H:1V. Recyclex TRM is rated for channel flows up to 17.0+ ft/s (5.2+ m/s) and shear stress up to 10.0+ lb/ft2 (480+ Pa) when vegetated.

Physical Properties: Fiber: 100% Recycled Post Consumer Polyester Fiber Size: 80% of fibers a minimum of 5 in (15.7 cm) long Fiber Weight: ≤ 400 Denier Polyester

Unit Weight: 0.625 lb/yd2 (0.34 kg/m2) ± 10% Thread Pattern: 1.5 in (3.8 cm) ± 0.50 in (1.3 cm) transverse stitch spacing Net Material: Polypropylene extra heavy duty black - top Polypropylene heavy duty black - bottom Net Openings: 0.75 in wide x 1.0 in long (19.1 mm x 25.4 mm) - top 0.75 in wide x 0.75 in long (19.1 mm x 19.1 mm) - bottom Net Configuration: Top and bottom

All measurements are based on product at time of manufacture.


W0114R0315


Rev 0610


P42 TRM Specification Sheet

The ErosionControlBlanket P42 is a turf reinforcement mat made of 100% polypropylene fiber (green or tan) designed for critical slope and channel applications requiring permanent erosion control and turf reinforcement. The matting is sewn together on 1.5 inch (38.1 mm) centers. The P42 meets all requirements established in the FHWA FP-03 as a Type 5 A, B, and C turf reinforcement matting for use on slopes with gradients up to 0.5:1 (h:v), channels, and shorelines. The P42 has been tested by the National Transportation Product Evaluation Program (NTPEP). The P42 comes packaged in clear shrink-wrap with a blue band and includes installation instructions. Product Nomenclature & Properties

P = 100% polypropylene fiber matrix (tan or green in color) 4 = polypropylene fiber matrix applied at a rate of 0.75 lbs/yd2 (400 g/m2) 2 = top permanent UV stabilized black net with a mesh size of 0.53 x 0.5 in (1.34 x 1.27 cm)

= bottom permanent UV stabilized black net with a mesh size of 0.626 x 0.626 in (1.59 x 1.59 cm) = permanent UV stabilized black thread


Mass per Unit Area ASTM D6475 12.7 oz/yd2 UV Stability at 500 hours ASTM D 4355 96%


Thickness ASTM D6525 0.446 in Light Penetration / Ground Cover ASTM D6567 20% / 80%


Soil Loss Ratio* = 6.29 Soil Loss Ratio*= 6.05 Soil Loss Ratio*= 5.81




Design Values

• “C” factor = 0.001 • Unvegetated Maximum Permissible Shear Stress = 3.30 lbs/ft2 (158.4 Pa) • Vegetated Maximum Permissible Shear Stress = 14.0 lbs/ft2 (665 Pa) • Maximum Flow Velocity Unvegetated = 12 ft/s (3.8 m/s) • Maximum Flow Velocity Vegetated = 21 ft/s (6.65 m/s) • Unvegetated Manning’s “n” = 0.03 (The hydraulic roughness coefficient will vary for vegetated conditions

based on vegetation stand height and density) Standard Roll Details Width 2.44m (8ft) 4.88m (16ft) Standard Length 25.7m (84.3ft) 25.7m (84.3ft) Area 62.7m2 (75yd2) 125.4m2 (150yd2) Weight ±10% 28kg (61lb) 56kg (122lb)z “Big Daddy” Roll Details Width 2.44m (8ft) 4.88m (16ft) Standard Length 102.8m (337.5ft) 102.8m (337.5ft) Area 250.8m2 (300yd2) 500m2 (600yd2) Weight ±10% 112kg (244 lb) 224kg (488 lb)

Propex Operating Company, LLC ⋅ 6025 Lee Highway, Suite 425 ⋅ PO Box 22788 ⋅ Chattanooga, TN 37422

ph 423 899 0444 ⋅ ph 800 621 1273 ⋅ fax 423 899 7619 Geotex®, Landlok®, Pyramat®, X3®, SuperGro®, Petromat® and Petrotac® are registered trademarks of Propex Operating Company, LLC. This publication should not be construed as engineering advice. While information contained in this publication is accurate to the best of our knowledge, Propex does not warrant its accuracy or completeness. The ultimate customer and user of the products

should assume sole responsibility for the final determination of the suitability of the information and the products for the contemplated and actual use. The only warranty made by Propex for its products is set forth in our product data sheets for the product, or such

other written warranty as may be agreed by Propex and individual customers. Propex specifically disclaims all other warranties, express or implied, including without limitation, warranties of merchantability or fitness for a particular purpose, or arising from

provision of samples, a course of dealing or usage of trade.

© 2011 Propex Operating Company, LLC

Product Data

TESTED. PROVEN. TRUSTED. www.geotextile.com

LANDLOK 300 ® turf reinforcement mat (TRM) is a three-dimensional, lofty, woven polypropylene geotextile that is available in green or tan which is specially designed for erosion control applications on steep slopes and vegetated waterways. The matrix is composed of polypropylene monofilament yarns f e a t u r i n g X 3 ® t e c h n o l o g y woven into a uniform configuration of resilient pyramid-like projections. The material exhibits very high interlock and reinforcement capacity with both soil and root systems, demonstrates superior UV resistance, and enhances seedling emergence. LANDLOK 300 ® conforms to the property values listed below1 and is manufactured at a Propex facility having achieved ISO 9001:2000 certification. Propex performs internal Manufacturing Quality Control (MQC) tests that have been accredited by the Geosynthetic Accreditation Institute – Laboratory Accreditation Program (GAI-LAP). This product is NTPEP approved for AASHTO standards. MARV2 PROPERTY TEST METHOD ENGLISH METRIC ORIGIN OF MATERIALS % U.S. Manufactured Inputs 100% 100% % U.S. Manufactured 100% 100% PHYSICAL Mass/Unit Area ASTM D-6566 7.5 oz/yd2 254.3 g/m2

Thickness ASTM D-6525 0.25 in 6.35 mm Light Penetration (% Passing) ASTM D-6567 50% (Max) 50% Color Visual Green or Tan MECHANICAL Tensile Strength (Grab) ASTM D-6818 2000 x 1800 lb/ft 29.2 x 26.3 kN/m Elongation ASTM D-6818 50% (max) 50% (max) Resiliency ASTM D-6524 70% 70% Flexibility ASTM D-6575 0.195 in-lb (avg) 225,000 mg-cm (avg) ENDURANCE UV Resistance % Retained 3000 hrs ASTM D-4355 90% 90%

PERFORMANCE Velocity3 (Vegetated) Large Scale 20 ft/sec 6.10 m/sec

Shear Stress3 (Vegetated) Large Scale 12 lb/ft2 575 Pa Manning's "n" 4 (Unvegetated) Calculated 0.030 0.030 Seedling Emergence4 ECTC Draft Method #4 - - ROLL SIZES 8.5 ft x 106 ft 2.6 m x 32.3 m NOTES: 1. The property values listed are effective 04/2011 and are subject to change without notice. 2. MARV indicates minimum average roll value calculated as the typical minus two standard deviations. Statistically, it yields a 97.7% degree of confidence that any sample taken

during quality assurance testing will exceed the value reported. 3. Maximum permissible velocity and shear stress has been obtained through vegetated testing programs featuring specific soil types, vegetation classes, flow conditions, and

failure criteria. These conditions may not be relevant to every project nor are they replicated by other manufacturers. Please contact Propex for further information. 4. Calculated as typical values from large-scale flexible channel lining test programs with a flow depth of 6 to 12 inches.

LANDLOK 300®


ph 423 899 0444 ⋅ ph 800 621 1273 ⋅ fax 423 899 7619 Geotex®, Landlok®, Pyramat®, X3®, SuperGro®, Petromat® and Petrotac® are registered trademarks of Propex Operating Company, LLC. This publication should not be construed as engineering advice. While information contained in this publication is accurate to the best of our knowledge, Propex does not warrant its accuracy or completeness. The ultimate customer and user of the products

should assume sole responsibility for the final determination of the suitability of the information and the products for the contemplated and actual use. The only warranty made by Propex for its products is set forth in our product data sheets for the product, or such

other written warranty as may be agreed by Propex and individual customers. Propex specifically disclaims all other warranties, express or implied, including without limitation, warranties of merchantability or fitness for a particular purpose, or arising from

provision of samples, a course of dealing or usage of trade.


Product Data


PYRAMAT ® high performance turf reinforcement mat (HPTRM) is a three-dimensional, lofty, woven polypropylene geotextile that is available in green or tan which is specially designed for erosion control applications on steep slopes and vegetated waterways. The matrix is composed of polypropylene monofilament yarns f e a t u r i n g X 3 ® t e c h n o l o g y woven into a uniform configuration of resilient pyramid-like projections. The material exhibits very high interlock and reinforcement capacity with both soil and root systems, demonstrates superior UV resistance, and enhances seedling emergence. PYRAMAT conforms to the property values listed below1 and is manufactured at a Propex facility having achieved ISO 9001:2000 certification. Propex performs internal Manufacturing Quality Control (MQC) tests that have been accredited by the Geosynthetic Accreditation Institute – Laboratory Accreditation Program (GAI-LAP). This product is NTPEP approved for AASHTO standards. MARV2 PROPERTY TEST METHOD ENGLISH METRIC

ORIGIN OF MATERIALS

% U.S. Manufactured Inputs 100% 100% % U.S. Manufactured 100% 100% PHYSICAL Mass/Unit Area ASTM D-6566 13.5 oz/yd2 457.7g/m2

Thickness ASTM D-6525 0.4 in 10.2 mm Light Penetration (% Passing) ASTM D-6567 15% (Max) 15% (Max) Color Visual Green or Tan MECHANICAL Tensile Strength (Grab) ASTM D-6818 4000 x 3000 lb/ft 58.4 x 43.8 kN/m Elongation ASTM D-6818 40 x 35% 40 x 35% Resiliency ASTM D-6524 80% 80% Flexibility ASTM D-6575 0.534 in-lb (avg) 615,000 mg-cm (avg) ENDURANCE UV Resistance % Retained 6000 hrs ASTM D-4355 90% 90%

UV Resistance % Retained 10000 hrs ASTM D-4355 85% 85%

PERFORMANCE Velocity3 (Fully Vegetated) Large Scale 25 ft/sec 7.6 m/sec

Shear Stress3 (Fully Vegetated) Large Scale 16lb/ft2 766 Pa Manning's "n" 4 (Unvegetated) Calculated 0.028 0.028

Seedling Emergence4 ECTC Draft Method #4 296% 296% ROLL SIZES 8.5 ft x 90 ft 2.6 m x 27.4 m NOTES: 1. The property values listed are effective 04/2011 and are subject to change without notice.

2. MARV indicates minimum average roll value calculated as the typical minus two standard deviations. Statistically, it yields a 97.7% degree of confidence that any sample taken during quality assurance testing will

exceed the value reported.

3. Maximum permissible velocity and shear stress has been obtained through vegetated testing programs featuring specific soil types, vegetation classes, flow conditions, and failure criteria. These conditions

may not be relevant to every project nor are they replicated by other manufacturers. Please contact Propex for further information.

4. Calculated as typical values from large-scale flexible channel lining test programs with a flow depth of 6 to 12 inches.

PYRAMAT®

ARMORMAX® Anchored Reinforced Vegetation System (ARVS) consists of a high performance Turf Reinforcement Mat (HPTRM) and percussion driven earth anchors that work together to lock soil in place and resist movement. This easy-to-install, permanent erosion protection can be used in vegetated or unvegetated applications. Anchors (type as specified by the engineer) act as a tie-down mechanism for additional safety and long-term design life.

APPLICATIONSFor use in extreme erosion control applications:• Green-friendly, synthetic armoring for earthen levees• Canal, stream, and river bank protection from erosion and scour• Arid and/or semi-arid storm water channels and slopes

For use in shallow plane slope failure applications:• Canal embankment stabilization• Slope stabilization

FEATURES & BENEFITSIn extreme erosion control applications:• Reduces erosion, reinforces vegetation• Withstands hydraulic stresses including high water flows and wave impact• Minimizes settlement/subsidence of poor quality soils and need for future soil lifts to maintain levee elevation• Allows for enlargement of levees for controlled overtopping• Withstands non-hydraulic stresses from debris flow, loading of tractors, etc.• Promotes infiltration of surface water• UV stabilized with 50 year design life

For use in shallow plane slope failure applications:• Minimizes lane closure times and construction hazards in highway applications• Provides erosion protection and stabilizes sloughing slopes• Earth percussion anchors secure the HPTRM to subgrade and tie soil mass together to provide stability• Engineered percent open area to provide both short-term and long-term protection• Environmentally-friendly solution for improving groundwater quality and protecting wildlife

SAVINGS & ADVANTAGESARMORMAX® offers a cost-effective alternative to rock slope protection and soil nailing with shotcrete. Easy to install, saving on labor costs.

simplifying complexity Saving You Time, Money, and Resources

Infrastructure Solutions

GEOSYNTHETICS

CONCRETEREINFORCEMENT

SOIL & EROSIONCONTROL

For questions about Armormax® and other products:Call our technical help hotline at 1-800-214-2737 or visit us online at

Propexglobal.com by scanning the QR code with your smart phone.

www.propexglobal.com

Product Data

KEY PHYSICAL PROPERTIES OF ARMORMAX®

• Material Composition: Patented ultraviolet protection package in HPTRM, stainless steel tendons and galvanized threaded rods provide long-term design assurance.• TensileStrength:HPTRMboasts4000x3000lb/ft(58.4x43.8kN/m)oftensilestrength,whichexceedstheU.S.EPA’sdefinitionof a High Performance Turf Reinforcement Mat.• Seedling Emergence: HPTRM features X3®fibertechnology,whichoffers40%morefibersurfaceareatocapturethecriticalsediment andmoistureneededtoincreaseseedgerminationwithinthefirst21days.• Flexibility: Allows the system to conform and maintain contact with the prepared subgrade.• Holding Strength: Based on anchor size, tendon rod length and on-site soil parameters, the anchor foot provides up to an ultimate of 500 to 5000 lbs. of pullout resistance per earth percussion anchor. Actual holding strengths depend upon soil characterisitcs, anchor type and installation techniques.

NOTES: 1. The property values listed are effective 12/2006 and are subject to change without notice. 2. MARV indicates minimum average roll value calculated as the typpical minus two standard deviations. Statistically, it yields a 97.7% degree of confidence that any sample taken during quality assurance testing will exceed the value reported. 3. Maximum tendon/wedge grip strength capacity is 2000 lbs. Threaded rods with bolted steel plates up to 5000 lbs.

ArmorMax® Anchor Reinforced Vegetation System (ARVS) Property TablesPYRAMAT® HPTRM PROPERTIES

MARV2

PROPERTY TEST METHOD ENGLISH METRICORIGIN OF MATERIALS%U.S.ManufacturedInputs 100% 100%%U.S.Manufactured 100% 100%PHYSICALMass/Unit Area ASTM D-6566 13.5oz/yd2 457.7 g/m2

Thickness ASTMD-6525 0.4 in 10.2mmLightPenetration(%Passing) ASTM D-6567 15%(Max) 15%(Max)Color Visual Green or TanMECHANICALTensile Strength ASTMD-6818 4000 x 3000 lb/ft 58.4 x 43.8 kN/mElongation ASTMD-6818 40x35% 40x35%Resiliency ASTMD-6524 80% 80%Flexibility ASTM D-6575 0.534 in-lb (avg) 615,000mg-cm(avg)ENDURANCEUVResistance%Retained6000hrs ASTM D-4355 90% 90%UVResistance%Retained10000hrs ASTM D-4355 85% 85%

PERFORMANCEVelocity3 (Fully Vegetated) Large Scale 25ft/sec 7.6 m/secShear Stress3 (Fully Vegetated) Large Scale 16lb/ft2 766 PaManning’s “n” 4 (Unvegetated) Calculated 0.028 0.028Seedling Emergence4 ECTC Draft Method #4 296% 296%ROLL SIZES 8.5 ft x 90 ft 2.6mx27.4m

ANCHOR PROPERTIES

Anchor Type Anchor Length Load Range Ultimate Strength

TypeB1Anchor 3 ft (0.9 m)5ft(1.5m) 0 – 500 lbs 1,100lbs

TypeB2Anchor 6ft(1.8m)9ft(2.7m) 0–1,000lbs 2,600lbs

TypeB2Anchor 6ft(1.8m)9ft(2.7m) 0–1,500lbs 2,800lbs

Packaged in 50 lb. (22.6 kg. ) Plastic or multi-wall kraft bagsAvailable in palletized 18 bag units. Product certification and MSDS available upon request.

Fine lawn and turf establishment on slopes. Where mulch performance is critical. Erosion control on slopes of 2.5:1 or flatter.

Lawn and fine turf applications. Erosion control on slopes of 4:1 or flatter. Worldwide applications.

Where to use Mat-Fiber Where to use Mat-Fiber Plus

Mat-Fi

berMa

t-Fiber

®

®

Mat-FiberMat-Fiber

Mat-FiberMat-Fiber

® ®

® ®

Mat-Fi

berMa

t-Fiber

®

®

Plus

Mat-FiberMat-Fiber

Mat-FiberMat-Fiber

® ®

® ®

Plus

98% Wood Fiber Mulch 95% Wood Fiber Mulchwith 3% added tackifier

Ingredients:Wood fiber content................................................................98%Basic green dye....................................................................<1%Trade secret..........................................................................<1%

Composition:Organic matter (min.).........................................................99.3%Inorganic matter (ash) (max.)..............................................0.7%Moisture content (total weight base).............................12% 3%pH at 3% consistency in water slurry (avg.)...........................4.9Water-holding capacity (min.)......................................1.2gal./lb.

Ingredients:Wood fiber content................................................................95%Tackifier content by weight.....................................................3%Basic green dye.....................................................................<1%Trade secret...........................................................................<1%

Composition:Organic matter (min.).........................................................99.3%Inorganic matter (ash) (max.)..............................................0.7%Moisture content (total weight base).............................12% 3%pH at 3% consistency in water slurry (avg.)............................4.7Water-holding capacity (min.)......................................1.2gal./lb.

+-

+-

Mat-Fiber Mat-Fiber Plus

For more information call Mat. Inc. Customer Service1-888-477-3028 or visit our website at: www.matinc.biz

888-477-3028

Fax: 218-476-2039

[email protected]

Mat Inc.

12402 Hwy 2

Floodwood, MN 55736

2.02 MATERIALS

Bonded Fiber Matrix: Soil Guard® as manufactured by Mat, Inc. and/or Mat-NuWood, LLC, shall conform to the following typical property values when applied at a rate of 3000 lb/ac (3400 kg/ha).

TEST METHOD ENGLISH SI

Physical

Mass Per Unit Area ASTM D-6566 12.9 oz/yd2 440 g/m2

% Ground Cover ASTM D-6567 96.9% 96.9%

Water Holding Capacity ASTM D-7367 1273% 1273%

Cure Time Observed 24-48 hr 24-48 hr

Color (fugitive dye) Observed Yellow Yellow

Endurance

Functional Longevity Observed Up to 12 months Up to 12 months

Performance

Cover Factor ASTM D-6459 0.001(min) 0.001 (min)

Germination ASTM D-7322 713% 713%

% Effectiveness ECTC Test Method #2 99.9% (min) 99.9% (min)

One minus Cover Factor multiplied by 100% equals % effectiveness.

2.0 COMPOSITION

All components of the BFM shall be pre-packaged by the Manufacturer to assure material performance and compliance with the following typical values. Under no circumstances will field mixing of additives or components be accepted.

Thermally Processed Wood Fibers (moisture content 12% ± 3%) . . . . . . . . . . . .88% Proprietary Crosslinked Hydro-Colloid Tackifiers and Activators . . . . . .12% ± 1% 2.04 PACKAGING

Bags: Net Weight - 50 lb—UVI weather-resistant plastic or Kraft paper bag (MN location only) Pallets: Weather-proofed—plastic capped and stretch-wrapped or heat shrunk 5 mil plastic shroud

PART 3 EXECUTION

3.01 SUBSTRATE AND SEEDBED PREPARATION

A. Examine substrates and conditions where materials will be applied. Apply product to geotechnically stable slopes that have been designed and constructed to divert runoff away from the face of the slope. Do not proceed with installation until satisfactory conditions are established. B. Depending upon project sequencing and intended application, prepare seedbed in compliance with: Section 01570 - Temporary Erosion and Sediment Control Section 02300 - Earthwork; Establishment of Subgrade Section 02370 - Erosion and Sedimentation Control Section 02920 - Lawns and Grasses

3.02 INSTALLATION

PART 1 GENERAL

1.01 SUMMARY

This section specifies a hydraulically-applied Bonded Fiber Matrix (BFM) composed of long strand, thermally processed wood fibers and proprietary crosslinked, hydro-colloid tackifiers and activators. The BFM may require a 24-48 hour curing period to achieve maximum performance. Once cured, the BFM forms an intimate bond with the soil surface to create a continuous, absorbent, flexible erosion resistant blanket that allows for rapid germination and accelerated plant growth.

1.02 SUBMITTALS

A. Product Data: Submit manufacturer’s product data and installation instructions. Include required substrate preparation, list of materials, and application rate.

B. Certifications: Manufacturer shall submit a letter of certification that the products meets or exceeds all physical property, endurance, performance and packaging requirements.

1.03 DELIVERY, STORAGE, AND HANDLING

Deliver materials and products in UVI weather resistant factory labeled packages. Store and handle in strict compliance with manufacturer’s instructions and recommendations. Protect from damage from weather, excessive temperatures, and construction operations.

PART 2 PRODUCTS

2.01 ACCEPTABLE MANUFACTURER

Mat, Inc.12402 Hwy 2, Floodwood, MN 55736Phone 888-477-3028Fax 218-476-2039

Mat-NuWood, LLC811 Price Place, Lenoir, NC 28645Phone 828-758-4463Fax 828-754-3964

www.matinc.biz

Bonded Fiber Matrix(BFM)Soil Guard® Specification

Made in the U.S.A.

A Strictly comply with manufacturer’s installation instructions and recommendations. For optimum pumping and application performance use approved mechanically agitated, hydraulic seeding/mulching machines with a fan-type nozzle (50-degree tip). Apply BFM from opposing directions and to achieve best soil coverage.

B Erosion Control and Revegetation:

For maximum performance, apply BFM in a two-step process:

Step One: Mix and apply seed and soil amendments with small amount of BFM for visual metering.

Step Two: Mix and apply BFM at a rate of 50 lb per 100 gallons of water over freshly prepared surfaces. Confirm loading rates with equipment manufacturer. Do not leave seeded surfaces unprotected, especially if precipitation is imminent.

Depending upon site conditions BFM may be applied in a one-step process where all components may be mixed together in single tank loads. Consult with manufacturer for further details.

Do not apply on saturated soils or substrates. Do not apply if precipitation is anticipated within 24-48 hours. Minimum curing temperature is 40°F (4°C). Best results and more rapid curing are achieved at temperatures exceeding 60°F (15°C). Curing times may be accelerated in high temperature, low humidity conditions with product applied on dry soils.

Over-application of product may inhibit germination and plant growth.

C. Mixing:

A mechanically agitated hydraulic-application machine is recommended:

i. Fill tank to middle of agitator shaft or tank about 1/3 full of water. Turn on pump to wet or purge lines. Begin agitating. Keep adding water slowly while adding the BFM at a steady rate.

ii. Consult application and loading charts to determine number of bags to be added. Mix at a rate of 50 lbs. of BFM per 100 gallons. Contact equipment manufacturer to confirm optimum BFM mixing rates.

iii. All BFM should be loaded when the tank is approximately 3/4 full.

iv. Fertilizer should be added once the tank is nearly full. v. Before applying, mix the slurry for at least 10 minutes after

adding the last amount of BFM. This is very important to fully activate the bonding additives and to attain proper viscosity.

vi. Turn off recirculation valve to minimize potential for air entrainment within the slurry.

vii. Conduct Free water test.viii. Refer to manufacturer Guide for more detailed information.

D. Application:

Use a fan-type nozzle (50-degree tip) whenever possible for best soil surface coverage. Apply BFM from opposing directions to soil surface, reducing the “shadow effect” and assuring a minimum of 95% of soil surface coverage. Slope interruption devices or water diversion techniques are recommended when slope lengths exceed 50 feet (15m). Install materials at the following minimum application rates:

Condition English SI<3H to 1V 3000 lb/ac 3400 kg/ha

>3H to 1V and <2H to 1V 3500 lb/ac 3900 kg/ha>2H to 1V and <1H to 1V 4000 lb/ac 4500 kg/ha

Below ECB or TRM 1500 lb/ac 1700 kg/haAs infill for TRM 3500 lb/ac 3900 kg/ha

Increase application rates on highly erosive soils or chiseled, disked, furrowed or tracked slopes.

Material should not be applied in channels, swales or other areas where concentrated flows are anticipated, unless installed in conjunction with a temporary erosion control blanket or non-degradable turf reinforcement mat.

After application, thoroughly flush the tank, pumps and hoses to remove all BFM material. Wash all material from the exterior of the machine and remove any slurry spills. Once dry, BFM will be more difficult to remove.

3.03 CLEANING AND PROTECTION

Clean spills promptly. Advise Owner of methods for protection of treated areas. Do not allow treated areas to be trafficked or subjected to grazing.

Made in the U.S.A.

Mat, Inc.12402 Hwy 2, Floodwood, MN 55736

Phone 888-477-3028Fax 218-476-2039www.matinc.biz

Made in the U.S.A.

2.02 MATERIALS

Fiber Reinforced Matrix (FRM): Flex Guard® as manufactured by Mat, Inc. and shall conform to the following typical property values when applied at a rate of 3500 lb/ac (3900 kg/ha).

TEST METHOD ENGLISH SI

Physical

Mass Per Unit Area ASTM D-6566 11.6 oz/yd2 329 g/m2

% Ground Cover ASTM D-6567 99% 99%

Water Holding Capacity ASTM D-7367 1264% 1264%

Cure Time Observed 3 hr 3 hr

Color (fugitive dye) Observed Green Green

Endurance

Functional Longevity Observed Up to 18 months Up to 18 months

Performance

Cover Factor (6hr in/hr event) ASTM D-6459 0.005(min) 0.005 (min)

% Effectiveness ECTC Test Method #2 99.5% (min) 99.5% (min)

One minus Cover Factor multiplied by 100% equals % effectiveness.

2.0 COMPOSITION

All components of the FRM shall be pre-packaged by the Manufacturer to assure material performance and compliance with the following typical values. Under no circumstances will field mixing of additives or components be accepted.

Thermally Processed Wood Fibers (moisture content 12% ± 1) . . . . . . . . . . . . .83% Synthetic Fibers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4% ± 1% Proprietary Crosslinked Hydro-Colloid Tackifiers and Activators . . . . . .13% ± 1% 2.04 PACKAGING

Bags: Net Weight - 50 lb—UVI weather-resistant plastic bag. Pallets: Weather-proofed - plastic capped and stretched-wrapped or heat shrunk 5 mil plastic shroud.

PART 3 EXECUTION

3.01 SUBSTRATE AND SEEDBED PREPARATION

A. Examine substrates and conditions where materials will be applied. Apply product to geotechnically stable slopes that have been designed and constructed to divert runoff away from the face of the slope. Do not proceed with installation until satisfactory conditions are established. B. Depending upon project sequencing and intended application, prepare seedbed in compliance with: Section 01570 - Temporary Erosion and Sediment Control Section 02300 - Earthwork; Establishment of Subgrade Section 02370 - Erosion and Sedimentation Control Section 02920 - Lawns and Grasses

PART 1 GENERAL

1.01 SUMMARY

A. This section specifies a hydraulically appliedFiber Reinforced Matrix (FRM) composed of long strand, thermally processed wood fibers, synthetic fibers, proprietary cross linked hydro-colloid tackifiers, and activators. The FRM requires3 hours to provide limited protection if applied prior to or during light rain, but a 24-48 hour curing period is needed to achieve maximum performance. Once cured, the FRM forms an intimate bond with the soil surface to create a continuous, absorbent, flexible erosion resistantblanket that allows for rapid germination and accelerated plant growth.

1.02 SUBMITTALS

A. Product Data: Submit manufacturer’s product data and installation instructions. Include required substrate preparation, list of materials, and application rate.

B. Certifications: Manufacturer shall submit a letter of certification that the products meets or exceeds all physical property, endurance, performance and packaging requirements.

1.03 DELIVERY, STORAGE, AND HANDLING

Deliver materials and products in UV and weather resistant factory labeled packages. Store and handle in strict compliance with manufacturer’s instructions and recommendations. Protect fromdamage from weather, excessive temperatures, and construction operations.

PART 2 PRODUCTS

2.01 ACCEPTABLE MANUFACTURER

Mat, Inc.12402 Hwy 2, Floodwood, MN 55736Phone 888-477-3028Fax 218-476-2039

Mat-NuWood, LLC811 Price Place, Lenoir, NC 28645Phone 828-758-4463Fax 828-754-3964

www.matinc.biz

Fiber reinForced Matrix(FrM)Flex Guard® SpeciFication

Made in the U.S.A.

3.02 INSTALLATION

A Strictly comply with manufacturer’s installation instructions and recommendations. For optimum pumping and application performance use approved mechanically agitated, hydraulic seeding/mulching machines with a fan-type nozzle (50-degree tip). Apply FRM from opposing directions and to achieve best soil coverage.

B Erosion Control and Revegetation:

For maximum performance, apply FRM in a two-step process:

Step One: Mix and apply seed and soil amendments with small amount of FRM for visual metering.

Step Two: Mix and apply FRM at a rate of 50 lb per 100 gallons of water over freshly prepared surfaces. Confirm loading rates with equipment manufacturer. Do not leave seeded surfaces unprotected, especially if precipitation is imminent.

Depending upon site conditions FRM may be applied in a one-step process where all components may be mixed together in single tank loads. Consult with manufacturer for further details.

Minimum curing temperature is 40°F (4°C). Best results and more rapid curing are achieved at temperatures exceeding 60°F (15°C). Curing times may be accelerated in high temperature, low humidity conditions with product applied on dry soils. Over-application of product may inhibit germination and plant growth.

Over-application of product may inhibit germination and plant growth.

C. Mixing:

A mechanically agitated hydraulic-application machine is recommended:

i. Fill tank to middle of agitator shaft or tank about 1/3 full of water. Turn on pump to wet or purge lines. Begin agitating. Keep adding water slowly while adding the FRM at a steady rate.

ii. Consult application and loading charts to determine number of bags to be added. Mix at a rate of 50 lbs. of FRM per 100 gallons. Contact equipment manufacturer to confirm optimum FRM mixing rates.

iii. All FRM should be loaded when the tank is approximately 3/4 full.

iv. Fertilizer should be added once the tank is nearly full. v. Before applying, mix the slurry for at least 10 minutes after

adding the last amount of FRM. This is very important to fully activate the bonding additives and to attain proper viscosity.

vi. Turn off recirculation valve to minimize potential for air entrainment within the slurry.

vii. Conduct Free water test.viii. Refer to manufacturer Guide for more detailed information.

D. Application:

Use a fan-type nozzle (50-degree tip) whenever possible for best soil surface coverage. Apply FRM from opposing directions to soil surface, reducing the “shadow effect” and assuring a minimum of 95% of soil surface coverage. Slope interruption devices or water diversion techniques are recommended when slope lengths exceed 50 feet (15m). Install materials at the following minimum application rates:

Condition English SI<3H to 1V 3000 lb/ac 3400 kg/ha

>3H to 1V and <2H to 1V 3500 lb/ac 3900 kg/ha>2H to 1V and <1H to 1V 4000 lb/ac 4500 kg/ha

Below ECB or TRM 1500 lb/ac 1700 kg/haAs infill for TRM 3500 lb/ac 3900 kg/ha

Increase application rates on highly erosive soils or chiseled, disked, furrowed or tracked slopes.

Material should not be applied in channels, swales or other areas where concentrated flows are anticipated, unless installed in conjunction with a temporary erosion control blanket or non-degradable turf reinforcement mat.

After application, thoroughly flush the tank, pumps and hoses to remove all FRM material. Wash all material from the exterior of the machine and remove any slurry spills. Once dry, FRM will be more difficult to remove.

3.03 CLEANING AND PROTECTION

Clean spills promptly. Advise Owner of methods for protection of treated areas. Do not allow treated areas to be trafficked or subjected to grazing.

Made in the U.S.A.

Mat, Inc.12402 Hwy 2, Floodwood, MN 55736

Phone 888-477-3028Fax 218-476-2039www.matinc.biz

Made in the U.S.A.

SOIL SOLUTIONS SOIL SOLUTIONSSPEC TACK SPEC TACK

SPSP SPSPSpectack is an organic tackifier (dispersable Polysaccharide) manufactured in the USA and is specifically designed for use as a hydraulically applied erosion control tackifier. Spectack is used as a standalone temporary erosion control product with wood, paper, or other native fiber mulches to provide superior bonding strength. Spectack is specially designed to develop optimal slurry viscosity to improve sprayability and pump performance. Spectack disperses in water creating a lump free slurry, saving time and money.

Recommended Application Rates:It is recommended that Spectack be applied at 10 to 25 lbs. per 1000 gallons of water depending on machines capacity. When used as an overspray for straw, use Spectack more concentrated at the rate of 40 lbs. to 1000 gallons of water per acre with the use of 150 to 300 lbs. of mulch as a marker.

SLOPE: Flat 4:1 3:1 2:1LBS/ACRE: 30-80 50-100 80-120 100-170

Safe Handling and Use:Precaution: Inhaling dust may irritate lungs and/or cause allergic responses in some individuals. Use caution as material will become slippery on wet deck surfaces. Store unused quantities in a cool, dry place. Not a plant food product.

Mixing Instructions:1. Add water to tank to cover blades of lower agitator.2. Add Spectack slowly while filling tank with agitator at high speed.3. After Spectack is thoroughly mixed, add mulch, seed and fertilizer.

For More Information call: 1-888-477-3028 Fax: 1-218-476-2039

Net. Wt. 40 lbs. (4-10 lbs. bags)

Spectack is an organic tackifier (dispersable Polysaccharide) manufactured in the USA and is specifically designed for use as a hydraulically applied erosion control tackifier. Spectack is used as a standalone temporary erosion control product with wood, paper, or other native fiber mulches to provide superior bonding strength. Spectack is specially designed to develop optimal slurry viscosity to improve sprayability and pump performance. Spectack disperses in water creating a lump free slurry, saving time and money.

Recommended Application Rates:It is recommended that Spectack be applied at 10 to 25 lbs. per 1000 gallons of water depending on machines capacity. When used as an overspray for straw, use Spectack more concentrated at the rate of 40 lbs. to 1000 gallons of water per acre with the use of 150 to 300 lbs. of mulch as a marker.

SLOPE: Flat 4:1 3:1 2:1LBS/ACRE: 30-80 50-100 80-120 100-170

Safe Handling and Use:Precaution: Inhaling dust may irritate lungs and/or cause allergic responses in some individuals. Use caution as material will become slippery on wet deck surfaces. Store unused quantities in a cool, dry place. Not a plant food product.

Mixing Instructions:1. Add water to tank to cover blades of lower agitator.2. Add Spectack slowly while filling tank with agitator at high speed.3. After Spectack is thoroughly mixed, add mulch, seed and fertilizer.

For More Information call: 1-888-477-3028 Fax: 1-218-476-2039

Net. Wt. 40 lbs. (4-10 lbs. bags)

Ver. 0213

www.bioticearth.com

PHONE: (866) 280-7327 FAX: (866) 757-7327

A subsidiary of ErosionControlBlanket

Biotic EarthTM Black HGM Hydraulic Growth Medium

Specification Sheet The Verdyol Biotic EarthTM Black HGM shall be an extremely biotic-active hydraulically applied mulch and

growth medium that includes a high concentration of soil builders and affords highly effective erosion control. The

Biotic EarthTM Black HGM shall be specifically designed to assist in building an effective plant growth medium

over poor topsoil or even subsoil. The Biotic EarthTM Black HGM shall be used for vegetation establishment, on

medium to extreme slopes for immediate erosion control, as a soil amendment with other erosion control measures,

and where vegetation establishment is expected to occur within 12 months or less.

The Biotic EarthTM Black HGM shall be manufactured from thermally and mechanically processed straw and

flexible flax fibers with sphagnum peat moss and other proprietary plant growth materials and erosion control

additives. The Verdyol Biotic EarthTM Black HGM comes packaged in white bags.

The Verdyol Biotic EarthTM Black HGM may be considered a Hydraulic Mulch (HM) as defined by the Erosion

Control Technology Council. The Verdyol Biotic EarthTM Black HGM may be considered a Stabilized Mulch

Matrix (SMM) when used in conjunction with EarthBound® 2000 and EarthBound® Scientific Soil Stabilizer &

Tackifier.

Material Composition 40% by volume of thermally and mechanically processed straw and flexible flax fibers (FFF)

57% by volume of professional grade sphagnum peat moss

1.26% by volume other valuable trace minerals, sugars, starches, proteins, fiber and 16 amino acids including folic

acid, vitamin A, triaconnatol and triacontanol growth stimulants/regulators.

<1% by volume fungal mycorrhizae and plant beneficial bacteria

Laboratory Analysis Total Organic Matter Content = >95%

Carbon:Nitrogen Ratio = 31:1

Moisture Content = 44.5% ± 5%

pH = 5.5 (Saturated Media Extract Method) These values are representative of Quality Control Analysis at time of manufacturing.

This data is for information purposes only and cannot be used as a warranty.

Packaging & Weights Bags = 50 lbs (23 kg) +/- 10%

Bag size = 2.2 ft3 (0.062 m3)

36 bags per pallet EarthBound® is a registered trademark of Terra Novo, Inc.

Willacoochee Industrial Fabrics, Inc. PO Box 599 • 769 West Main Street • Willacoochee, GA 31650 Ph: (912) 534-5757 • Fax: (912) 534-5533

WINFAB 1215DT is manufactured using high tenacity polypropylene yarns that are woven to form a dimensionally stable network, which allows the yarns to maintain their relative position. WINFAB 1215DT resists ultraviolet deterioration, rotting, and biological degradation and is inert to commonly encoun-tered soil chemicals.

PROPERTY TEST METHOD MARV English MARV MetricTensile Strength (Grab) ASTM D-4632 150 x 100 lbs 667.23 x 444.82 NElongation ASTM D-4632 8% 8%UV Resistance (500 hrs) ASTM D-4355 80% 80%Apparent Opening Size (AOS)* ASTM D-4751 30 US Std. Sieve 0.60 mmPermittivity ASTM D-4491 .5 sec ˉ¹ .5 sec ˉ¹

Water Flow Rate ASTM D-4491 50 gpm/ft² 2037 lpm/m2

Disclaimer: Willacoochee Industrial Fabrics assumes no liability for the completeness or accuracy of this information or the ultimate use of this information. Willacoochee Industrial Fab-rics disclaims any and all implied, expressed, or statutory standards, guarantees, or warranties. This includes without limitation any implied warranty as to merchantability or fitness for a particular purpose or arising from a course of dealing or usage of trade as to equipment, materials, or information furnished herewith. This document should not be construed as engineer-ing advice. Always consult the project engineer for project specific requirements. The end user assumes sole responsibility for the use of this information and product. The property values listed above are subject to change without notice. © 2013 Willacoochee Industrial Fabrics, Inc.

*Maximum Average Roll Valve Notes:• Mullen Burst ASTM D-3786 has been removed. It is not recognized by ASTM D-35 on Geosynthetics.• Puncture ASTM D-4833 has been removed. It is not recognized by AASHTO M288 and has been replaced with CBR Puncture ASTM D-6241

PROPERTY Typical English Typical MetricRoll Dimensions 36 in x 500 ft

36 in x 1000 ft36 in x 1500 ft

.914 x 152.4 m

.914 x 304.8 m

.914 x 457.2 m

WINFAB 1215DT

Enviro-USA’s Floating Turbidity Curtains (also known as Turbidity Barriers or Silt Curtains) create a barrier toprevent turbid (cloudy) water from entering clear water. Floating Turbidity Curtains should be used to isolateactive construction areas within or adjacent to a body of water to control and contain silt and sediment.

Enviro-USA Type 2 Impermeable Floating Turbidity BarrierProduct Data/Technical Information

FLOATATION: 8” Polystyrene float with a buoyancy of 61 lbs/ft2, sufficient to keep the barrierat a minimal elevation of 3 inches above the water line.

SKIRT DEPTH: Skirt depth will be based on project requirements.

FABRIC: 18 or 22 oz/yd2 reinforced Vinyl Fabric (PVC) yellow in color, with UVinhibitors and a minimum grab tensile strength of 500 lbs.

TOP TENSION CABLE: 5/16” galvanized top load carrying cable placed immediately above floatation.Cable is finished off at aluminum connectors in order to transfer anddistribute any load across other barriers. Breaking Strength is 10,000 lbs.

BOTTOM LOAD CHAIN: 5/16” galvanized ballast and bottom load carrying chain, placed at bottom edgeof skirt. Chain is finished off on both ends with 5/16” shackles, to allowsections to connect and transfer any load. Chain is enclosed in a pocket.Breaking Strength is 7,600 lbs, weight is 1 lb/ft.

CONNECTORS/ENDS: Top 18” consist of ASTM Marine Grade Aluminum Universal Slideconnectors and grommets for lacing from below the connector to the bottomedge of skirt. Extreme edges are reinforced with 5/8” poly rope.

SEAMS: All horizontal seams are 100% heat welded and all vertical seams are 100% RFwelded as recommended by fabric manufacturers.

Added Features: - Grab handle at every connector.(at no extra cost) - Anchor Point at connector for attaching anchor systems.

- Zip-Ties for tying skirts together.- Private Labeling on every section if desired.

APPLICATION: Type 2 Turbidity Curtains are ideal for moving water applications such as: rivers,inland waterways, harbors, protected ports and lakes with wind and or current.

DOT- COMPLIANT: Enviro-USA’s Type 2 Turbidity Curtains are compliant with mostD.O.T.’s Type 2 – Medium Duty and or Moving Water requirements.

Changes to this product can be made in order to comply with customer, D.O.T or project requirements.

Special Specification

Erosion EelsTM

1. Description. Furnish, install, maintain, and remove Erosion EelsTM as shownon plans or as directed.

2. Materials.

1. Core Material. Erosion EelsTM shall consist of core, internal filter materialscomprised of one of two mixtures:

I. Mixture Specification 1.0. A filter mixture comprised of 100% shreddedrubber that has been washed and processed to remove most, if not all,metal components. The material shall be derived from recycled tires andshall be shredded to produce a maximum particle size of +/- ¾ inch.

II. Mixture Specification 2.0. A filter mixture comprised of 100% shreddedrubber that has been washed and processed to remove most, if not all,metal components. The material shall be derived from recycled tires andshall be shredded to produce a maximum particle size of +/-2-inches.

2. Containment Material. The containment material for the filter core particlesshall be a woven, polypropylene geotextile with UV-stabilizers and inert tobiological decay and chemically resistant to naturally occurring chemicals, alkalis,and acids. Minimum fabric permeability shall be equal to or greater than 0.05cm/sec per ASTM D 4491. Minimum strength retained relative to UV exposureshall be 70% when tested per ASTM D 4355 for 500 hours.

3. Size. Erosion EelsTM shall be produced with a nominal diameter of +/-9.5 inchesand +/-20 inches and standard nominal lengths of +/-4.5 feet and +/-10 feet.

3. Construction. Install Erosion EelsTM near the downstream perimeter of a disturbedarea to intercept sediment from sheet flow. Incorporate the Erosion EelsTM into theerosion control measures used to the control sediment on construction sites. Install,align, and locate the Erosion EelsTM as specified below, as shown on the plans, asdirection.

A. Stabilizing/Securing. Secure Erosion EelsTM in a method adequate toprevent displacement as a result of normal rain events and such that flow isnot allowed under the bags.

B. Maintenance. Inspect and maintain the Erosion EelsTM in good condition.Maintain the integrity of the control, including keeping the bags free ofaccumulated silt, debris, etc., until permanent erosion control features are inplace, or the disturbed area has been adequately stabilized. Stabilize theareas damaged by the removal process using appropriate methods asapproved. Repair or replace damaged Erosion EelsTM as required and asdirected. Temporarily remove and replace Erosion EelsTM as required tofacilitate work. Remove sediment and debris when accumulation affects the

performance of the devices, after a rain, and when directed. Dispose of sediment and debris at an approved site in a manner that will not contribute to additional siltation.

C. Removal. Remove and reuse Erosion EelsTM when directed.

4. Measurement. This item will be measured by the linear foot along the centerline ofthe top of the control bags.

5. Payment. The work performed and materials furnished in accordance with this itemand measured as provided under “Measurement” will be paid for a the unit price bidfor “Erosion EelsTM” of the size specified. This price is full compensation forfurnishing, placing, maintaining, temporarily removing and replacing as required tofacilitate construction operations, and removing of the bags and for all othermaterials, labor, tools, equipment, and incidentals.

End-of Section

Note: Specifications are subject to revisions at the discretion of the Manufacturer.

© 2009, Denny Hastings and Friendly Environment

Miller Seed Company 1600 Cornhusker Hwy Lincoln, NE 68521 Phone (402) 438-1232 Fax (402) 438-1068 www.MillerSeed.com

PROPEX ROLL SIZE MIRAFI

351 12.5'x360'/15'x360' 135N401 12.5'x360'/15'x360' 140N451 15'x360' 150N

*601 12.5'x360'/15'x300' 160N**801 12.5'x360'/15'x300' 180N1001 15'x300' 1100N1601 15'x300' 1160N

200ST 12.5'x432'/17.5'x309' 500X315ST 12.5'x432'/17.5'x309' 600X

104F 6'x300'/12'x300' FW700111F 12.5'x300'117F 12'x300'

2x2HF 15'x300' HP2703x3HF 12.5'x360'/15'x300' HP3704x4HF 15'x300' HP570

Soil Reinforcement

Shaded Items are Stocked by Miller Seed*IDOT Rip Rap Fabric / **NDOR Rip Rap Fabric

GEOTEXTILE COMPARISON

NON-WOVEN FABRICDrainage, Seperation, Stabilization

WOVEN FABRIC

MONOFILAMENT FABRIC

HIGH-STRENGTH WOVEN FABRIC

Filtration

Seperation, Stabilization

http://www.millerseed.com/

AASHTO M-288 RECOMMENDED PRODUCTSAASHTO M-288 RECOMMENDED PRODUCTSAASHTO M-288 RECOMMENDED PRODUCTSAASHTO M-288 RECOMMENDED PRODUCTS

ApplicationApplicationApplicationApplication NonwovenNonwovenNonwovenNonwoven WovenWovenWovenWoven

≤15% in Situ Soil passing 0.075

mmGeotex 801 Geotex 2x2HF

15 to 50% in Situ Soil passing

0.075 mmGeotex 801 -

>50% in Situ Soil passing 0.075

mmGeotex 801 -


mmGeotex 601 -


0.075 mmGeotex 601 Geotex 104F


mmGeotex 601 Geotex 104F


mmGeotex 401 -




mmGeotex 401 -

Geotex 801 Geotex 315ST





mmGeotex 801 Geotex 2x2HF




mmGeotex 801 -


mmGeotex 601 Geotex 104F




mmGeotex 601 -

Geotex 351 -

- Geotex 2130

Paving Fabric Petromat 4598 -

Permanent Erosion

Control

Temporary Silt

Fence

Supported

Unsupported

-

Class 3

(Use Class 3 only if specified by

engineer – see note b of table 2 in

M288 spec)

Class 1

(Geotextiles other than woven

monofilaments)

Class 2

(Woven Monofilament Geotextiles

or other geotextiles as specified by

engineer - see note c of table 6 in

M288 specs)

Class 2 (Use class 2 only if specified by engineer – see note a of table

5 in M288 spec)

Class 3 (Use class 3 only if specified by engineer – see note a of table

5 in M288 spec)

Stabilization

Class 1



ClassClassClassClass

Subsurface

Drainage

Class 1

Class 2

Separation

Class 1

Class 2

Class 3

PropexGlobal.comPropex Operating Company, LLC

Propex Operating Company, LLC 1110 Market Street, Suite 300 Chattanooga, TN 37402 USA

PH: 800-621-1273 F: 423-899-5005 PropexGlobal.com Geotex®, Landlok®, Pyramat®, X3®, SuperGro®, Petromat® and Petrotac® are registered trademarks of Propex Operating Company, LLC. This publication should not be construed as engineering advice. While information contained in this publication is accurate to the best of our knowledge, Propex does not warrant its accuracy or completeness. The ultimate customer and user of the products should assume sole responsibility for the final determination of the suitability of the information and the products for the contemplated and actual use. The only warranty made by Propex for its products is set forth in our product data sheets for the product, or such other written warranty as may be agreed by Propex and individual customers. Propex specifically disclaims all other warranties, express or implied, including without limitation, warranties of merchantability or fitness for a particular purpose, or arising from provision of samples, a course of dealing or usage of trade.


PRODUCT DATA • GEOTEX 200ST


ph 423 899 0444 ⋅ ph 800 621 1273 ⋅ fax 423 899 7619 Geotex®, Landlok®, Pyramat®, X3®, SuperGro®, Petromat® and Petrotac® are registered trademarks of Propex Operating Company, LLC. This publication should not be construed as engineering advice. While information contained in this publication is accurate to the best of our knowledge, Propex does not warrant its accuracy or completeness. The ultimate customer and user of the products should

assume sole responsibility for the final determination of the suitability of the information and the products for the contemplated and actual use. The only warranty made by Propex for its products is set forth in our product data sheets for the product, or such other

written warranty as may be agreed by Propex and individual customers. Propex specifically disclaims all other warranties, express or implied, including without limitation, warranties of merchantability or fitness for a particular purpose, or arising from provision of

samples, a course of dealing or usage of trade.



Product Data

GEOTEX 200ST is a woven polypropylene geotextile containing heavy woven flat tape yarns produced by Propex, and will meet the following Minimum Average Roll Values (MARV) when tested in accordance with the methods listed below. These characteristics make GEOTEX 200ST ideal for the construction of embankments over soft soils, steepened slopes, and modular block and/or wrapped-face retaining walls. The geotextile is resistant to ultraviolet degradation and to biological and chemical environments normally found in soils. GEOTEX 200ST conforms to the property values listed below1 , as well as meets the requirements set forth by AASHTO M-288/NTPEP (Geotextile Specification for Highway Application). Propex performs internal Manufacturing Quality Control (MQC) tests that have been accredited by the Geosynthetic Accreditation Institute – Laboratory Accreditation Program (GAI-LAP). This product is NTPEP approved for AASHTO standards.

MARV2 PROPERTY TEST METHOD ENGLISH METRIC ORIGIN OF MATERIALS % U.S. Manufactured Inputs 100% 100% % U.S. Manufactured 100% 100% MECHANICAL Tensile Strength (Grab) ASTM D-4632 200 lbs 890 N Elongation ASTM D-4632 12% 12% CBR Puncture ASTM D-6241 700 lbs 3115 N Trapezoidal Tear ASTM D-4533 75 lbs 333.8 N ENDURANCE UV Resistance % Retained at 500 hrs ASTM D-4355 70% 70%

HYDRAULIC Apparent Opening Size (AOS)3 ASTM D-4751 40 US Std. Sieve 0.425 mm Permittivity ASTM D-4491 0.05 sec-1 0.05 sec-1 Water Flow Rate ASTM D-4491 4 gpm/ft2 163 lpm/m2

ROLL SIZES 12.5 ft x 432 ft 15.0 ft x 360 ft 17.5 ft x 309 ft

3.81 m x 131.7 m 4.57 m x 109.7 m 5.33 m x 94.2 m

NOTES: 1. The property values listed above are effective 04/2011 and are subject to change without notice. 2. Values shown are in weaker principal direction. Minimum average roll values (MARV) are calculated as the typical minus

two standard deviations. Statistically, it yields a 97.7% degree of confidence that any samples taken from quality assurance testing will exceed the value reported.

3. Maximum average roll value.

GEOTEX 200ST

15% 15%








Product Data

GEOTEX 315ST is a woven polypropylene geotextile containing heavy woven tape/fibrillated yarns produced by Propex, and will meet the following Minimum Average Roll Values (MARV) when tested in accordance with the methods listed below. These characteristics make GEOTEX 315ST ideal for the construction of embankments over soft soils, steepened slopes, and modular block and/or wrapped-face retaining walls. The geotextile is resistant to ultraviolet degradation and to biological and chemical environments normally found in soils. GEOTEX 315ST conforms to the property values listed below1, as well as meets the requirements set forth by AASHTO M-288/NTPEP (Geotextile Specification for Highway Application). Propex performs internal Manufacturing Quality Control (MQC) tests that have been accredited by the Geosynthetic Accreditation Institute – Laboratory Accreditation Program (GAI-LAP). This product is NTPEP approved for AASHTO standards.

MARV2 PROPERTY TEST METHOD ENGLISH METRIC ORIGIN OF MATERIALS % U.S. Manufactured Inputs 100% 100% % U.S. Manufactured 100% 100% MECHANICAL Tensile Strength (Grab) ASTM D-4632 315 lbs 1402 N Elongation ASTM D-4632 12% 12% CBR Puncture ASTM D-6241 900 lbs 4005 N Trapezoidal Tear ASTM D-4533 120 lbs 533 N ENDURANCE UV Resistance % Retained at 500 hrs ASTM D-4355 70% 70%


ROLL SIZES 12.5 ft x 360 ft 15.0 ft x 300 ft 17.5 ft x 258 ft

3.8 m x 109.8 m 4.6 m x 91.5 m 5.3 m x 78.6 m




GEOTEX 315ST








Product Data

GEOTEX 350ST is a woven polypropylene geotextile containing heavy woven tape/fibrillated yarns produced by Propex, and will meet the following Minimum Average Roll Values (MARV) when tested in accordance with the methods listed below. These characteristics make GEOTEX 350ST ideal for the construction of embankments over soft soils, steepened slopes, and modular block and/or wrapped-face retaining walls. The geotextile is resistant to ultraviolet degradation and to biological and chemical environments normally found in soils. GEOTEX 350ST conforms to the property values listed below1, as well as meets the requirements set forth by AASHTO M-288/NTPEP (Geotextile Specification for Highway Application). Propex performs internal Manufacturing Quality Control (MQC) tests that have been accredited by the Geosynthetic Accreditation Institute – Laboratory Accreditation Program (GAI-LAP).

MARV2 PROPERTY TEST METHOD ENGLISH METRIC ORIGIN OF MATERIALS % U.S. Manufactured Inputs 100% 100% % U.S. Manufactured 100% 100% MECHANICAL Tensile Strength (Grab) ASTM D-4632 450 x 350 lbs 2002 x 1557 N Elongation ASTM D-4632 15% 15 % Wide Width Tensile ASTM D-4595 3600 x 3240 lbs/ft 52.6 x 47.3 kN/m Wide Width Elongation ASTM D-4595 8% 8% Wide Width Tensile at 5% Strain ASTM D-4595 1356 lbs/ft 19.8 kN/m CBR Puncture ASTM D-6241 1200 lbs 5340 N Trapezoidal Tear ASTM D-4533 130 lbs 578.5 N ENDURANCE UV Resistance % Retained at 500 hrs ASTM D-4355 70% 70%


ROLL SIZES 15.0 ft x 300 ft 12.5 ft x 300 ft

4.6 m x 91.5 m 3.8 m x 91.5m




GEOTEX 350ST








Product Data

GEOTEX 2X2HF is a woven polypropylene geotextile containing heavy woven monofilament/fibrillated yarns produced by Propex, and will meet the following Minimum Average Roll Values (MARV) when tested in accordance with the methods listed below. These characteristics make GEOTEX 2X2HF ideal for the construction of embankments over soft soils, steepened slopes, and modular block and/or wrapped-face retaining walls. The geotextile is resistant to ultraviolet degradation and to biological and chemical environments normally found in soils. GEOTEX 2X2HF conforms to the property values listed below.1 Propex performs internal Manufacturing Quality Control (MQC) tests that have been accredited by the Geosynthetic Accreditation Institute – Laboratory Accreditation Program (GAI-LAP). This product is NTPEP approved for AASHTO standards.

MARV2 PROPERTY TEST METHOD ENGLISH METRIC ORIGIN OF MATERIALS % U.S. Manufactured Inputs 100% 100% % U.S. Manufactured 100% 100% MECHANICAL Tensile Strength (Grab) ASTM D-4632 315 x 315 lbs 1401.8 x 1401.8 N Elongation ASTM D-4632 15% 15% Wide Width Tensile ASTM D-4595 2400 x 2400 lbs/ft 35.0 x 35.0 kN/m Wide Width Elongation ASTM D-4595 12 x 8% 12 x 8% Wide Width Tensile at 2% Strain ASTM D-4595 240 x 240 lbs/ft 3.5 x 3.5 kN/m

Wide Width Tensile at 5% Strain ASTM D-4595 780 x 1404 lbs/ft 11.4 x 20.5 kN/m

Wide Width Tensile at 10% Strain ASTM D-4595 1800 x 2520 lbs/ft 26.2 x 36.8 kN/m

CBR Puncture ASTM D-6241 1400 lbs 6230 N Trapezoidal Tear ASTM D-4533 125 lbs 556 N ENDURANCE UV Resistance % Retained at 500 hrs ASTM D-4355 90% 90%

HYDRAULIC Apparent Opening Size (AOS)3 ASTM D-4751 40 US Std. Sieve 0.425 mm Permittivity ASTM D-4491 0.70 sec-1 0.70 sec-1 Water Flow Rate ASTM D-4491 50 gpm/ft2 2037 lpm/m2 ROLL SIZES 15.0 ft x 300 ft 4.6 m x 91.5 m NOTES: 1. The property values listed above are effective 04/2011 and are subject to change without notice. 2. Values shown are in weaker principal direction. Minimum average roll values (MARV) are calculated as the typical minus two standard deviations. Statistically, it yields a 97.7% degree of

confidence that any samples taken from quality assurance testing will exceed the value reported. 3. Maximum average roll value.

GEOTEX 2x2HF

product data • GEOTEX 3X3HF

MARV2 PROPERTY TEST METHOD ENGLISH METRIC

ORIGIN OF MATERIALS % U.S. Manufactured Inputs 100% 100% % U.S. Manufactured 100% 100% MECHANICAL Wide Width Tensile ASTM D-4595 3600 x 3600 lbs/ft 52.6 x 52.6 kN/m Wide Width Elongation ASTM D-4595 10 x 5% 10 x 5% Wide Width Tensile at 2% Strain

ASTM D-4595 480 x 420 lbs/ft 7.0 x 6.1 kN/m

Wide Width Tensile at 5% Strain




CBR Puncture ASTM D-6241 1600 lbs 7120 N Trapezoidal Tear ASTM D-4533 170 x 125 lbs 756 x 556 N ENDURANCE UV Resistance % Retained at 500 hrs

ASTM D-4355 80% 80%

HYDRAULIC Apparent Opening Size (AOS)3 ASTM D-4751 30 US Std. Sieve 0.600 mm Permittivity ASTM D-4491 0.52 sec-1 0.52 sec-1

Water Flow Rate ASTM D-4491 40 gpm/ft2 1629.8 lpm/m2

ROLL SIZES 12.5 ft x 360 ft 15.0 ft x 300 ft

3.81 m x 109.8 m 4.57 m x 91.5 m

GEOTEX 3X3HF is a woven polypropylene geotextile containing heavy monofilament/ fibrillated yarns produced by Propex, and will meet the following Minimum Average Roll Values (MARV) when tested in accordance with the methods listed below. These characteristics make GEOTEX 3X3HF ideal for the construction of embankments over soft soils, steepened slopes, and modular block and/or wrapped-face retaining walls. The geotextile is resistant to ultraviolet degradation and to biological and chemical environments normally found in soils.

GEOTEX 3X3HF conforms to the property values listed below.1 Propex performs internal Manufacturing Quality Control (MQC) tests that have been accredited by the Geosynthetic Accreditation Institute – Laboratory Accreditation Program (GAI-LAP). This product is NTPEP approved for AASHTO standards.

NOTES:1. The property values listed above are effective 04/2011 and are subject to change without notice.2. Values shown are in weaker principal direction. Minimum average roll values (MARV) are calculated as the typical minus two standard deviations. Statistically, it yields a 97.7% degree

of confidence that any samples taken from quality assurance testing will exceed the value reported.3. Maximum average roll value.

product data • GEOTEX 4X4HF

GEOTEX 4X4HF is a woven polypropylene geotextile containing heavy woven serrated/serrated yarns produced by Propex, and will meet the following Minimum Average Roll Values (MARV) when tested in accordance with the methods listed below. These characteristics make GEOTEX 4X4HF ideal for the construction of embankments over soft soils, steepened slopes, modular block and/or wrapped-face retaining walls and subgrade reinforcement/stabilization for road construction. The geotextile is resistant to ultraviolet degradation and to biological and chemical environments normally found in soils.

GEOTEX 4X4HF conforms to the property values listed below.1 Propex performs internal Manufacturing Quality Control (MQC) tests that have been accredited by the Geosynthetic Accreditation Institute – Laboratory Accreditation Program (GAI-LAP). This product is NTPEP approved for AASHTO standards.


ORIGIN OF MATERIALS % U.S. Manufactured Inputs 100% 100% % U.S. Manufactured 100% 100% MECHANICAL Wide Width Tensile ASTM D-4595 4800 x 4800 lbs/ft 70.1 x 70.1 kN/m Wide Width Tensile at 2% Strain






CBR Puncture ASTM D-6241 2000 lbs 8900 N Trapezoidal Tear ASTM D-4533 180 lbs 801N ENDURANCE UV Resistance % Retained at 500 hrs

ASTM D-4355 80% 80%

HYDRAULIC Apparent Opening Size (AOS)3 ASTM D-4751 30 US Std. Sieve 0.600 mm Permittivity ASTM D-4491 0.40 sec-1 0.40 sec-1 Water Flow Rate ASTM D-4491 30 gpm/ft2 1222 lpm/m2 ROLL SIZES 15.0 ft x 300 ft 4.6 m x 91.5 m

NOTES:1. The property values listed above are effective 04/2011 and are subject to change without notice.2. Values shown are in weaker principal direction. Minimum average roll values (MARV) are calculated as the typical minus two standard deviations. Statistically, it yields a 97.7% degree of

confidence that any samples taken from quality assurance testing will exceed the value reported.3. Maximum average roll value.








Product Data

GEOTEX 104F is a woven monofilament polypropylene geotextile produced by Propex, and will meet the following Minimum Average Roll Values (MARV) when tested in accordance with the methods listed below. The individual filaments are woven into a regular network and calendared such that filaments retain dimensional stability relative to each other. These characteristics make GEOTEX 104F ideal for filtration beneath hard armor systems. The geotextile is resistant to ultraviolet degradation and to biological and chemical environments normally found in soils. GEOTEX 104F conforms to the property values listed below.1 Propex performs internal Manufacturing Quality Control (MQC) tests that have been accredited by the Geosynthetic Accreditation Institute – Laboratory Accreditation Program (GAI-LAP). This product is NTPEP approved for AASHTO standards.

MARV2 PROPERTY TEST METHOD ENGLISH METRIC ORIGIN OF MATERIALS % U.S. Manufactured Inputs 100% 100% % U.S. Manufactured 100% 100% MECHANICAL Tensile Strength (Grab) ASTM D-4632 370 x 250 lbs 1,647 x 1113 N Elongation ASTM D-4632 15 x 15% 15 x 15% CBR Puncture ASTM D-6241 950 lbs 4228 N Trapezoidal Tear ASTM D-4533 100 x 60 lbs 445 x 267 N ENDURANCE UV Resistance % Retained at 500 hrs ASTM D-4355 90% 90%

HYDRAULIC Apparent Opening Size (AOS)3 ASTM D-4751 70 US Std. Sieve 0.212 mm Percent Open Area CW-02215 MOD. 4 4-6 % 4-6 % Permittivity ASTM D-4491 0.28 sec-1 0.28 sec-1 Water Flow Rate ASTM D-4491 18 gpm/ft2 733 lpm/m2

ROLL SIZES 6 ft x 300 ft 12 ft x 300 ft

1.83 m x 91.5 m 3.66 m x 91.5 m



3. Maximum average roll value. 4. Army Corp of Engineers test method correlated to light emitted through fabric. (Area of Openings/Total Area X 100%)

GEOTEX 104F

product data • GEOTEX 111F

GEOTEX 111F is a woven polypropylene geotextile produced by Propex, and will meet the following Minimum Average Roll Values (MARV) when tested in accordance with the methods listed below. The individual filaments are woven into a regular network such that filaments retain dimensional stability relative to each other. These characteristics make GEOTEX 111F ideal for filtration beneath hard armor systems and around leachate collection pipes. The geotextile is resistant to ultraviolet degradation and to biological and chemical environments normally found in soils.

GEOTEX 111F conforms to the property values listed below.1 Propex performs internal Manufacturing Quality Control (MQC) tests that have been accredited by the Geosynthetic Accreditation Institute – Laboratory Accreditation Program (GAI-LAP).


ORIGIN OF MATERIALS % U.S. Manufactured Inputs 100% 100% % U.S. Manufactured 100% 100% MECHANICAL Tensile Strength (Grab) ASTM D-4632 370 x 220 lbs 1646 x 979 N Elongation ASTM D-4632 20 x 15% 20 x 15% CBR Puncture ASTM D-6241 1250 lbs 5563 N Trapezoidal Tear ASTM D-4533 115 x 75 lbs 511 x 334 N ENDURANCE UV Resistance % Retained at 500 hrs

ASTM D-4355 90% 90%

HYDRAULIC Apparent Opening Size (AOS)3 ASTM D-4751 30 US Std. Sieve 0.600 mm

Percent Open Area CW-02215 MOD. 4

8% 8%

Permittivity ASTM D-4491 1.50 sec-1 1.50 sec-1 Water Flow Rate ASTM D-4491 115 gpm/ft2 4,685.6 lpm/m2 ROLL SIZES 12.5 ft x 300 ft 3.81 m x 91.5 m

NOTES:1. The property values listed above are effective 04/2011 and are subject to change without notice.2. Values shown are in weaker principal direction. Minimum average roll values (MARV) are calculated as the typical minus two

standard deviations. Statistically, it yields a 97.7% degree of confidence that any samples taken from quality assurance testing will exceed the value reported.

3. Maximum average e roll value.4. Army Corp of Engineers test method correlated to light emitted through fabric. (Area of Openings/Total Area X 100%)







TESTED. PROVEN. TRUSTED www.geotextile.com

Product Data

GEOTEX® 401 is a polypropylene, staple fiber, needlepunched nonwoven geotextile produced by Propex, and will meet the following Minimum Average Roll Values (MARV) when tested in accordance with the methods listed below. The fibers are needled to form a stable network that retains dimensional stability relative to each other. The geotextile is resistant to ultraviolet degradation and to biological and chemical environments normally found in soils. GEOTEX 401 conforms to the property values listed below1. Propex performs internal Manufacturing Quality Control (MQC) tests that have been accredited by the Geosynthetic Accreditation Institute – Laboratory Accreditation Program (GAI-LAP). This product is NTPEP approved for AASHTO standards.

MARV2

PROPERTY TEST METHOD ENGLISH METRIC ORIGIN OF MATERIALS % U.S. Manufactured Inputs 100% 100% % U.S. Manufactured 100% 100% MECHANICAL Tensile Strength (Grab) ASTM D-4632 120 lbs 534 N Elongation ASTM D-4632 50% 50% CBR Puncture ASTM D-6241 310 lbs 1380 N Trapezoidal Tear ASTM D-4533 50 lbs 222 N ENDURANCE UV Resistance % Retained at 500 hrs ASTM D-4355 70% 70%


Permittivity ASTM D-4491 1.7 sec-1 1.7 sec-1

Water Flow Rate ASTM D-4491 140 gpm/ft2 5704 l/min/m2

ROLL SIZES 12.5 ft x 360 ft 15 ft x 360 ft

3.81 m x 109.8 m 4.57 m x 109.8 m

NOTES: 1. The property values listed above are effective 04/2011 and are subject to change without notice. 2. Values shown are in weaker principal direction. Minimum average roll values (MARV) are calculated as the typical minus two standard deviations.

Statistically, it yields a 97.7% degree of confidence that any samples taken from quality assurance testing will exceed the value reported. 3. Maximum average roll value.

GEOTEX® 401







Product Data



MARV2






3.81 m x 109.8 m 4.57 m x 91.5 m



GEOTEX® 601

Propex Operating Company, LLC 6025 Lee Highway, Suite 425 PO Box 22788 Chattanooga, TN 37422

ph 423 899 0444 ph 800 621 1273 fax 423 899 7619

Geotex

®, Landlok

®, Pyramat

®, X3

®, SuperGro

®, Petromat

® and Petrotac

® are registered trademarks of Propex Operating Company, LLC.

This publication should not be construed as engineering advice. While information contained in this publication is accurate to the best of our knowledge, Propex does not warrant its accuracy or completeness. The ultimate customer and user of the products should





ENGINEERING EARTH

www.geotextile.com

GEOTEX® 801 is a polypropylene, staple fiber, needlepunched nonwoven geotextile produced by Propex,

and will meet the following Minimum Average Roll Values (MARV) when tested in accordance with the methods listed below. The fibers are needled to form a stable network that retains dimensional stability relative to each other. The geotextile is resistant to ultraviolet degradation and to biological and chemical environments normally found in soils. GEOTEX 801 conforms to the property values listed below

1. Propex performs internal Manufacturing

Quality Control (MQC) tests that have been accredited by the Geosynthetic Accreditation Institute –

Laboratory Accreditation Program (GAI-LAP). This product is NTPEP approved for AASHTO standards.

MARV2

PROPERTY TEST METHOD ENGLISH METRIC

ORIGIN OF MATERIALS

% U.S. Manufactured Inputs 100% 100%

% U.S. Manufactured 100% 100% MECHANICAL

Tensile Strength (Grab) ASTM D-4632 205 lbs 912 N

Elongation ASTM D-4632 50% 50%

CBR Puncture ASTM D-6241 525 lbs 2336 N

Trapezoidal Tear ASTM D-4533 80 lbs 356 N ENDURANCE

UV Resistance % Retained at 500 hrs

ASTM D-4355 70% 70%

HYDRAULIC

Apparent Opening Size (AOS)

3

ASTM D-4751 80 US Std. Sieve 0.180 mm

Permittivity ASTM D-4491 1.5 sec-1

1.5 sec-1

Water Flow Rate ASTM D-4491 110 gpm/ft2

4482 l/min/m2


3.81 m x 109.8 m 4.57 m x 91.5 m



GEOTEX® 801








Product Data


MARV2





ROLL SIZES 15 ft x 300 ft 4.57 m x 91.5 m NOTES: 1. The property values listed above are effective 04/2011 and are subject to change without notice. 2. Values shown are in weaker principal direction. Minimum average roll values (MARV) are calculated as the typical minus two standard deviations.


GEOTEX® 1001

PRODUCT DATA • GEOTEX® 1201

GEOTEX 1201 is a polypropylene, staple fiber, needlepunched nonwoven geotextile produced by Propex, and will meet the following Minimum Average Roll Values (MARV) when tested in accordance with the methods listed below. The fibers are needled to form a stable network that retains dimensional stability relative to each other. The geotextile is resistant to ultraviolet degradation and to biological and chemical environments normally found in soils.

GEOTEX 1201 conforms to the property values listed below1. Propex performs internal Manufacturing Quality Control (MQC) tests that have been accredited by the Geosynthetic Accreditation Institute – Laboratory Accreditation Program (GAI-LAP). This product is NTPEP approved for AASHTO standards.

NOTES:1. The property values listed above are effective 04/2011 and are subject to change without notice.2. Values shown are in weaker principal direction. Minimum average roll values (MARV) are calculated as the typical minus two standard deviations.

Statistically, it yields a 97.7% degree of confidence that any samples taken from quality assurance testing will exceed the value reported.3. Maximum average roll value.

MARV2

PROPERTY TEST METHOD ENGLISH METRIC ORIGIN OF MATERIALS % U.S. Manufactured Inputs 100% 100% % U.S. Manufactured 100% 100% MECHANICAL Tensile Strength (Grab) ASTM D-4632 305 lbs 1357 N Elongation ASTM D-4632 50% 50% CBR Puncture ASTM D-6241 825 lbs 3671 N Trapezoidal Tear ASTM D-4533 115 lbs 512 N ENDURANCE UV Resistance % Retained at 500 hrs

ASTM D-4355 70% 70%




ROLL SIZES 15 ft x 300 ft 4.57 m x 91.5 m








Product Data


MARV2





ROLL SIZES 15 ft x 300 ft 4.57 m x 91.5 m NOTES: 1. The property values listed above are effective 04/2011 and are subject to change without notice. 2. Values shown are in weaker principal direction. Minimum average roll values (MARV) are calculated as the typical minus two standard deviations.


GEOTEX® 1601


ph 423 899 0444 ⋅ ph 800 621 1273 ⋅ fax 423 899 7619 Geotex®, Landlok®, Pyramat®, X3®, SuperGro®, Petromat® and Petrotac® are registered trademarks of Propex Operating Company, LLC. This publication should not be construed as engineering advice. While information contained in this publication is accurate to the best of our knowledge, Propex does not warrant its accuracy or completeness. The ultimate customer and user of the products should assume sole responsibility for the final determination of the suitability of the information and the products for the contemplated and actual use. The only warranty made by Propex for its products is set forth in our product data sheets for the product, or such other written warranty as may be agreed by Propex and individual customers. Propex specifically disclaims all other warranties, express or implied, including without limitation, warranties of merchantability or fitness for a particular purpose, or arising from provision of samples, a course of dealing or usage of trade.



Product Data

GRIDPRO™ BXP11 is a punched and drawn geogrid containing polypropylene that is integrally formed into a biaxial geogrid. GRIDPRO BXP11 will meet the following Minimum Average Roll Values (MARV) when tested in accordance with the methods listed below. These characteristics make GRIDPRO BXP11 ideal for the construction of unpaved or asphalt paved roads, steepened slopes, and modular block and/or wrapped-face retaining walls. The geogrid is resistant to ultraviolet degradation and to biological and chemical environments normally found in soils.

NOTES: 1. Unless notified otherwise, values shown are minimum average roll values determined in accordance with ASTM D4759-02. Brief descriptions of test

procedures are given in the following notes. 2. Nominal dimensions. 3. True resistance to elongation when initially subjected to a load determined in accordance with ASTM D6637-01 without deforming test materials under load

before measuring such resistance or employing “secant” or “offset” tangent methods of measurement so as to overstate tensile properties. 4. Load transfer capability determined in accordance with GRI-GG2-05 and expressed as a percentage of ultimate tensile strength. 5. Resistance to bending force determined in accordance with ASTM D5732-01, using specimens of width two ribs wide, with transverse ribs cut flush with exterior

edges of longitudinal ribs (as a “ladder”), and of length sufficiently long to enable measurement of the overhang dimension. 6. Resistance to in-plane rotational movement measured by applying a 20 kg-cm (2 m-N) moment to the central junction of a 9 inch x 9 inch specimen restrained at

its perimeter in accordance with the U.S. Army Corps of Engineers Methodology for measurement of Torsional Rigidity. 7. Resistance to loss of load capacity or structural integrity when subjected to mechanical installation stress in clayey sand (SC), well graded sand (SW), and crushed

stone classified as poorly graded gravel (GP). The geogrid shall be sampled in accordance with ASTM D6637-01. 8. Resistance to loss of load capacity or structural integrity when subjected to chemically aggressive environments in accordance with EPA 9090 immersion testing. 9. Resistance to loss of load capacity or structural integrity when subjected to 500 hours of ultraviolet light and aggressive weathering in accordance with ASTM

D4355-05.

MARV PROPERTY Units MD Values1 XMD Values1 ORIGIN OF MATERIALS % U.S. Manufactured Inputs 100% 100% % U.S. Manufactured 100% 100% INDEX PROPERTIES Aperture Dimensions2 mm (in) 25 (1.0) 33 (1.3) Minimum Rib Thickness2 mm (in) 0.76 (0.03) 0.76 (0.03) Tensile Strength @ 2% Strain3 kN/m (lb/ft) 4.1 (280) 6.6 (450) Tensile Strength @ 5% Strain3 kN/m (lb/ft) 8.5 (580) 13.4 (920) Ultimate Tensile Strength3 kN/m (lb/ft) 12.4 (850) 19.0 (1,300) STRUCTURAL PROPERTIES Junction Efficiency4 % 93 93 Flexural Stiffness5 mg-cm 250,000 250,000 Aperture Stability6 m-N/deg 0.32 0.32 DURABILITY Resistance to Installation Damage7 %SC/%SW/%GP 95/93/90 95/93/90

Resistance to Long Term Degradation8 % 100 100

Resistance to UV Degradation9 % 100 100

ROLL SIZES m (ft) 3.0 x 75.0 (9.8 x 246) 4.0 x 75.0 (13.1 x 246)

GRIDPRO™ BXP11 TYPE 1

Propex Operating Company, LLC 6025 Lee Highway, Suite 425 PO Box 22788 Chattanooga, TN 37422

ph 423 899 0444 ph 800 621 1273 fax 423 899 7619

Geotex®, Landlok®, Pyramat®, X3®, SuperGro®, Petromat® and Petrotac® are registered trademarks of Propex Operating Company, LLC.

This publication should not be construed as engineering advice. While information contained in this publication is accurate to the best of our knowledge, Propex does not warrant its accuracy or completeness. The ultimate

customer and user of the products should assume sole responsibility for the final determination of the suitability of the information and the products for the contemplated and actual use. The only warranty made by Propex for

its products is set forth in our product data sheets for the product, or such other written warranty as may be agreed by Propex and individual customers. Propex specifically disclaims all other warranties, express or implied,

including without limitation, warranties of merchantability or fitness for a particular purpose, or arising from provision of samples, a course of dealing or usage of trade.


www.geotextile.com

GRIDPRO™ BXP12 is a punched and drawn geogrid containing polypropylene that is integrally formed into

a biaxial geogrid. GRIDPRO BXP12 will meet the following Minimum Average Roll Values (MARV) when

tested in accordance with the methods listed below. These characteristics make GRIDPRO BXP12 ideal

for the construction of unpaved or asphalt paved roads, steepened slopes, and modular block and/or

wrapped-face retaining walls. The geogrid is resistant to ultraviolet degradation and to biological and

chemical environments normally found in soils.

NOTES: 1. Unless notified otherwise, values shown are minimum average roll values determined in accordance with ASTM D4759-02. Brief descriptions of test

procedures are given in the following notes.

2. Nominal dimensions.

3. True resistance to elongation when initially subjected to a load determined in accordance with ASTM D6637-01 without deforming test materials under load

before measuring such resistance or employing “secant” or “offset” tangent methods of measurement so as to overstate tensile properties.

4. Load transfer capability determined in accordance with GRI-GG2-05 and expressed as a percentage of ultimate tensile strength.

5. Resistance to bending force determined in accordance with ASTM D5732-01, using specimens of width two ribs wide, with transverse ribs cut flush with exterior

edges of longitudinal ribs (as a “ladder”), and of length sufficiently long to enable measurement of the overhang dimension.

6. Resistance to in-plane rotational movement measured by applying a 20 kg-cm (2 m-N) moment to the central junction of a 9 inch x 9 inch specimen restrained at

its perimeter in accordance with the U.S. Army Corps of Engineers Methodology for measurement of Torsional Rigidity.

7. Resistance to loss of load capacity or structural integrity when subjected to mechanical installation stress in clayey sand (SC), well graded sand (SW), and crushed

stone classified as poorly graded gravel (GP). The geogrid shall be sampled in accordance with ASTM D6637-01.

8. Resistance to loss of load capacity or structural integrity when subjected to chemically aggressive environments in accordance with EPA 9090 immersion testing.

9. Resistance to loss of load capacity or structural integrity when subjected to 500 hours of ultraviolet light and aggressive weathering in accordance with ASTM

D4355-05.

MARV

PROPERTY Units MD Values1 XMD Values1

ORIGIN OF MATERIALS

% U.S. Manufactured Inputs 100% 100%

% U.S. Manufactured 100% 100%

INDEX PROPERTIES

Aperture Dimensions2 mm (in) 25 (1.0) 33 (1.3)

Minimum Rib Thickness2 mm (in) 1.27 (0.05) 1.27 (0.05)

Tensile Strength @ 2% Strain3 kN/m (lb/ft) 6.0 (410) 9.0 (620)

Tensile Strength @ 5% Strain3 kN/m (lb/ft) 11.8 (810) 19.6 (1,340)

Ultimate Tensile Strength3 kN/m (lb/ft) 19.2 (1,310) 28.8 (1,970)

STRUCTURAL PROPERTIES

Junction Efficiency4 % 93 93

Flexural Stiffness5 mg-cm 750,000 750,000

Aperture Stability6 m-N/deg 0.65 0.65

DURABILITY

Resistance to Installation

Damage7 %SC/%SW/%GP 95/93/90 95/93/90

Resistance to Long Term

Degradation8 % 100 100

Resistance to UV

Degradation9 % 100 100

ROLL SIZES m (ft) 3.0 x 50.0 (9.8 x 164)

4.0 x 50.0 (13.1 x 164)

Product Data

GRIDPRO™ BXP12 TYPE 2

Date post:	19-Apr-2021
Category:	Documents
Upload:	others
View:	4 times
Download:	0 times

2015 EROSION CONTROL TECHNICAL BULLETINS · 2016. 2. 25. · Thickness ASTM D6525 0.351 in Light...

Documents