2016 Cable Splicing Courses The electrical training ALLIANCE will be offering medium voltage (2,001-35,000 volts) cable splicing classes at several different locations in 2016. Module I, of the cable splicing courses, covers basic cable preparation and other fundamental topics pertinent to cable splicing. After successfully completing Module I, subsequent Modules may be taken in any order. The National Cable Splicers Certification Board inc. has been conducting both the written and practical certification examinations following the Module IV classes. Both Modules I and IV are perfect preparation courses for the written and practical NCSCB inc. examinations. If you are interested in taking the NCSCB inc. certification examinations, you must register separately for these exams at the NCSCB inc. website at www.ncscbinc.org. See cable splicing course information below. Watch the electrical training ALLIANCE website for additional classes. Contact Steve Anderson at 301.715.2340 with any questions. Cable Splicing Module I Prerequisites: None Length: 36 hours Overview: This is the first module of the electrical training ALLIANCE’s (NJATC) six-module, hands-on cable splicing series. This module covers hand-taped splices and terminations. The course presents information on several types of cable splices (different specifications are examined). Different cable types, tools used in splicing, different insulation types and the various types of insulation shielding are covered. The importance of proper cable preparation is covered in detail. This module reviews many theory areas that will benefit all those doing medium voltage work and preparing those that will be taking the NCSCB written examination. All students attending the module I course will also receive a cable splicing tool kit worth $120. Dates and Locations: February 22 – 26, 2016 Riverside/ San Bernardino JATC - San Bernardino, CA March 7 – 11, 2016 ALBAT Training Facility, Medway, OH August 22 – 26, 2016 ALBAT Training Facility, Medway, OH Course #: X011 Course Session #: See electrical training ALLIANCE website for session # and registration form. Course: Minimum: 8 students Maximum: 10 students Cost: $1,300.00 Cable Splicing Module II Prerequisites: Module I or Previous Hand-Taping Cable Splicing Experience Length: 36 hours Overview: Module II covers several methods of terminating cable, Tee splices, and protective grounds. Knot tying and the splicing of rope are also covered. The hands-on exercises include the construction of 5 kV and 15 kV terminations, 5 and 15 kV Tee splices, tying various knots and splicing rope. This module is also great preparation for the National Cable Splicing Certification Board’s Hand Taped splicing certification practical examination.
Transcript
2016 Cable Splicing Courses The electrical training ALLIANCE will be offering medium voltage (2,001-35,000 volts) cable splicing classes at several different locations in 2016. Module I, of the cable splicing courses, covers basic cable preparation and other fundamental topics pertinent to cable splicing. After successfully completing Module I, subsequent Modules may be taken in any order. The National Cable Splicers Certification Board inc. has been conducting both the written and practical certification examinations following the Module IV classes. Both Modules I and IV are perfect preparation courses for the written and practical NCSCB inc. examinations. If you are interested in taking the NCSCB inc. certification examinations, you must register separately for these exams at the NCSCB inc. website at www.ncscbinc.org. See cable splicing course information below. Watch the electrical training ALLIANCE website for additional classes. Contact Steve Anderson at 301.715.2340 with any questions.
Cable Splicing Module I Prerequisites: None
Length: 36 hours
Overview: This is the first module of the electrical training ALLIANCE’s (NJATC) six-module, hands-on cable splicing series. This module covers hand-taped splices and terminations. The course presents information on several types of cable splices (different specifications are examined). Different cable types, tools used in splicing, different insulation types and the various types of insulation shielding are covered. The importance of proper cable preparation is covered in detail. This module reviews many theory areas that will benefit all those doing medium voltage work and preparing those that will be taking the NCSCB written examination. All students attending the module I course will also receive a cable splicing tool kit worth $120.
Dates and Locations:
February 22 – 26, 2016 Riverside/ San Bernardino JATC - San Bernardino, CA
March 7 – 11, 2016 ALBAT Training Facility, Medway, OH
August 22 – 26, 2016 ALBAT Training Facility, Medway, OH
Course #: X011
Course Session #: See electrical training ALLIANCE website for session # and registration form.
Course: Minimum: 8 students Maximum: 10 students
Cost: $1,300.00
Cable Splicing Module II Prerequisites: Module I or Previous Hand-Taping Cable Splicing Experience
Length: 36 hours
Overview: Module II covers several methods of terminating cable, Tee splices, and protective grounds. Knot tying and the splicing of rope are also covered. The hands-on exercises include the construction of 5 kV and 15 kV terminations, 5 and 15 kV Tee splices, tying various knots and splicing rope. This module is also great preparation for the National Cable Splicing Certification Board’s Hand Taped splicing certification practical examination.
Dates and Locations: April 4 – 8 , 2016 ALBAT Training Facility, Medway, OH
June 6 – 10, 2016 Riverside/ San Bernardino JATC - San Bernardino, CA
Course #: X012
Course Session #: See electrical training ALLIANCE website for session # and registration form.
Course: Minimum: 8 students Maximum: 10 students
Cost: $1,125.00
Cable Splicing Module III Prerequisites: Module I or Previous Cable Splicing Experience
Length: 36 hours
Overview: Module III covers cable insulation testing and cable fault locating. Besides covering different test instruments and uses, several taping methods and rule-of-thumb dimensions will be used during the hands-on cable splicing exercises.
Dates and Locations:
May 2 – 6, 2016 ALBAT Training Facility, Medway, OH
Course #: X013 Course Session #: See electrical training ALLIANCE website for session # and registration form.
Course: Minimum: 8 students Maximum: 10 students
Cost: $1,085.00
Cable Splicing Module IV Prerequisites: Module I or Previous Cable Splicing Experience
Length: 36 hours
Overview: Module IV covers termination and splice kits. The course presents information on 12 different types of cable splices and termination kits used in the field today. Heat shrink, cold shrink, and molded products are used and studied. The students will become familiar with 3M cold shrink and molded products, Inertia/Repl heat shrink products and Prysmian cold shrink and cable products. This class uses not only a qualified Electrical Training ALLIANCE instructor, but technical experts from each manufacturer to help the students have a thorough understanding of the proper installation procedures and understand how important it is to follow these procedures.
Dates and Locations:
March 7 – 10, 2016 Riverside/ San Bernardino JATC - San Bernardino, CA
May 16 – 20, 2016 ALBAT Training Facility, Medway, OH October 10 – 14, 2016 ALBAT Training Facility, Medway, OH
Course #: X014
Course Session #: See electrical training ALLIANCE website for session # and registration form.
Course: Minimum: 8 students Maximum: 12 students
Cost: $1,925.00
Cable Splicing Module V - Lead Cable Splicing Prerequisites: Module I or Previous Cable Splicing Experience
Length: 64 hours
Overview: Students will learn to hand wipe a 3-conductor lead-to-lead splice. Safety will be discussed thoroughly. Students will be working with pots of molten lead and will learn proper sealing and insulating techniques. They will also learn pulling techniques, what materials and equipment are needed for splicing lead cable, and fireproofing procedures. 90% of the course time will be spent on hands-on activities. This class will be conducted over 7 consecutive days working up to 10 hours per day.
Date and Location:
April 23 – 30, 2016 ALBAT Training Facility, Medway, OH
Course #: X015
Course Session #: See electrical training ALLIANCE website for session # and registration form.
Course: Minimum: 10 students Maximum: 15 students
Cost: $2,875.00
Cable Splicing Module VI – Splicing and Terminating Cables on Wind Farms Prerequisites: None - But, Previous Cable Splicing Experience is Helpful
Length: 32 hours
Overview: This cable splicing course focuses on cable splicing and terminating 35 kV solid dielectric cables used on wind farm projects. This particular course session is for those who will be teaching this module VI course at their local programs or for their contractors. All students registering for this class should have taken prior cable splicing courses or have cable splicing experience. In classroom sessions and hands-on exercises, this course will show proper cable preparation practices for 35 kV, JCN cables using specialized tools. Students will be instructed in the proper use and care of these tools. The lessons and hands-on exercises will also cover both cold shrink and heat shrink 35 kV terminations and splices. Safety requirements and necessary certifications required for working on wind farm projects will be discussed. This will be an intensive 36 hour course with most of the time spent on hands-on exercises.
Dates and Locations:
April 18 – 22, 2016 Riverside/ San Bernardino JATC - San Bernardino, CA
June 20 – 24, 2016 ALBAT Training Facility, Medway, OH
Course #: X185
Course Session #: See electrical training ALLIANCE website for session # and registration form.
Course: Minimum: 8 students Maximum: 12 students
Cost: $2,750.00 See next page for order information from
GraybaR for all your Module Kits 1 - IV
IN COLLABORATION WITH:
These kits contain expendable materials which are needed for each student in the Electrical Training ALLIANCE Cable Splicing Module 1, 2, 3, and 4 courses.
• Stocked in Regional zones to ensure prompt delivery• Consistent pricing for all JATCs (ask your Graybar representative for details) • Each module kit contains all required parts for simplicity and convenience
For more information, visit graybar.com/jatc/3M-cable-splicing
Cable Splicing Module Kits AvailableTO ORDER CALL (800) 330-8249 OR YOUR LOCAL GRAYBAR SALES REPRESENTATIVE.
Scotch® Linerless Electrical Splicing Tape 130C; 3/4'' x 30' 9
Scotch® Super 33+™ Vinyl Electrical Tape 3/4"X 66' 6
Scotch® Electrical Grounding Braid 25, 15' Coil 1
Scotch® Rubber Splicing Tape 23; 3/4'' x 30' 9
Scotch® Vinyl Color Coding Electrical Tape 35; Red 1/2" x 20' 1
Scotch® Electrical Shielding Tape 24; 1'' x 15' 5
Scotch® Semi-Conducting Tape 13; 3/4'' X 15' 3
IN COLLABORATION WITH:
These kits contain expendable materials which are needed for each student in the Electrical Training ALLIANCE Cable Splicing Module 1, 2, 3, and 4 courses.
• Stocked in Regional zones to ensure prompt delivery• Consistent pricing for all JATCs (ask your Graybar representative for details) • Each module kit contains all required parts for simplicity and convenience
For more information, visit graybar.com/jatc/3M-cable-splicing
Cable Splicing Module Kits AvailableTO ORDER CALL (800) 330-8249 OR YOUR LOCAL GRAYBAR SALES REPRESENTATIVE.
