116
2018 PRODUCT CATALOG
2018 PRODUCT CATALOG
GEISSELE TRIGGERSPERFORMANCE ADVANTAGES FOR THE SHOOTEROur triggers and hammers are made from quality S7 tool steel. The sear surfaces are precisely cut by a wire EDM machine. The non-directional
surface finish of this machine enables a smooth trigger pull without the associated grittiness of directional machining marks normally left by a
milling machine. The initial force needed to start the disengagement of the sear surfaces is low, and the force linearly increases at a low rate.
This helps the hammer to fall at the desired point of aim and builds shooter confidence in the weapon’s ability to place rounds on the point of
aim. A full force hammer spring is used for quick lock-time and positive ignition of all ammunition types. No lightened hammer spring is used.
The hammer itself is lighter than a standard AR15 hammer, further decreasing lock-time and increasing accuracy of the weapon. The net effect
is a greater accuracy and precision while shooting on the move, shooting with the weapon in movement, and during increased cadences of fire.
ADVANTAGES FOR THE ARMORERThe number of parts to a Geissele non-adjustable trigger is identical to a mil-spec trigger. There are no adjustment screws to come loose. All
springs are captive; they will not get lost during disassembly in the field. The entire trigger can be disassembled for cleaning (no rivets or staked
parts) .The trigger can be installed without removing the safety. Sear engagement is preset from the factory. Hammer and trigger pins are a
close slip fit into nominal receiver holes so the trigger can be installed and removed with rudimentary tools. Triggers come with a slave pin for
the trigger/disconnector assembly for easy installation.
SAFETY ADVANTAGESThe two-stage trigger has a generous overlap of the sear surfaces which contributes to safety and a low tendency of any inadvertent movement
of the trigger to discharge the weapon. Geissele’s non-adjustable triggers offer a patented pseudo-sear that is almost identical to the standard
AR-15 single stage sear. However, this secondary sear has surfaces that never touch during normal operation. This prevents the hammer from
falling unless the trigger is pulled. The secondary safety sear contributes to shooter confidence in dynamic/vehicle situations where a fellow
shooter’s muzzle may cover him. There is firm knowledge that even with the safety in the fire position the weapon can never discharge unless
the trigger is pulled. The trigger is designed to operate in dusty and abrasive environments.
GEISSELE
LOW
ER PARTSSUPER SEMI-AUTOMATIC (SSA®)The Geissele Super Semi-Automatic trigger is a semi-automatic only version of the
Geissele Automatics Super Select-Fire trigger. The SSA® is a 4.5 lb. non-adjustable
precision combat trigger that allows precise and accurate trigger control. The SSA’s
two-stage design allows the trigger to be light enough for accurate and precise shots,
but heavy and forgiving enough to be safe.
The Geissele SSA is safety certified by Crane Naval Surface Warfare Center. It is
recommended for demanding applications such as Law Enforcement, Close Quarters
Battle (CQB) and mid-range carbine work.
SUPER SEMI-AUTOMATIC (SSA®) SOPMOD $240
SUPER DYNAMIC-COMBAT (SD-C) $240
SUPER TRICON (SUPER T) $240
MSRP / SSA® VARIANT OPTIONS
MILITARY LAW ENFORCEMENT
HUNTING
INTENDED APPLICATION
SSA® SOPMOD CERTIFIED
SD - C
SUPER T
SOPMODCERTIFIED
GEISSELE
LOW
ER PARTSSUPER SEMI-AUTOMATIC ENHANCED (SSA-E)Built on the chassis of the Geissele SSA, the Super Semi-Automatic Enhanced provides
enhanced trigger control and weapon accuracy while maintaining the robustness and
reliability of our combat-proven two-stage trigger.
The SSA-E’s reduced first and second stage pull weights result in a trigger with a
smooth, light first stage take-up and a crisp, candy cane-like second stage break.
The SSA-E is ideal for use in precision squad designated marksman type rifles where
weapon accuracy and reliability are critical and a non-adjustable drop in trigger is
desired.
SOPMODCERTIFIED
SSA -E
SD -E
SUPER SEMI-AUTOMATIC (SSA-E) SOPMOD $240
SUPER DYNAMIC-COMBAT (SD-E) $240
MSRP / SSA-E VARIANT OPTIONS
INTENDED APPLICATION
TARGET PRECISIONHUNTING
SUPER 3 GUN (S3G) The Geissele Super 3 Gun (S3G) is a semi-automatic, hybrid cross between a
single-stage trigger and a traditional 2-stage trigger. Its robust feel and light pull
weight, combined with a lightning-quick reset, make this trigger ideal for any 3 Gun
competitor. The Super Dynamic 3 Gun (SD-3G), a flat bow version of the S3G is also
available.
RACE & COMPETITION
TARGET
INTENDED APPLICATION
SUPER 3 GUN (S3G) $240
SUPER DYNAMIC - 3 GUN (SD-3G) $240
MSRP / S3G VARIANT OPTIONS
S3G
SD -3G
GEISSELE
LOW
ER PARTS
SUPER SCAR The Geissele Super SCAR is built on the combat-proven chassis of the SSA which was
safety certified by Crane Naval Surface Warfare Center. The Super SCAR is a 4.5 lb.
two-stage, non-adjustable combat trigger which allows precise and accurate trigger
control. The Super SCAR is designed to work with the factory FN polymer housing that
is supplied with all SCAR16 and SCAR17 rifles.
A Select-Fire version of this trigger is available. Please contact Geissele for pricing and
information.
SUPER SCAR SOPMOD $325
SELECT-FIRE CALL FOR PRICING
MSRP
INTENDED APPLICATION
MILITARY LAW ENFORCEMENT
HUNTING PRECISION
SUPER SCAR
GEISSELE
LOW
ER PARTSSOPMODCERTIFIED
SUPER SELECT FIRE (SSF®) The Geissele Super Select-Fire Trigger is a select-fire combat trigger that Geissele
Automatics developed for the U.S. Special Operations Community. The SSF® is a
non-adjustable combat style two-stage trigger that is available in 4.5 lb. and 5.5 lb.
configurations. In semi-automatic mode, the SSF is a precision two-stage trigger that
allows precise and accurate trigger control. In fully-automatic mode, the SSF is a single-
stage trigger with a smooth, continuous trigger pull and abrupt hammer release.
The SSF is safety certified by Crane Naval Surface Warfare Center.
NSN# 1005-01-618-8104 (M4 Carbine)
SSF ®
INTENDED APPLICATION
MILITARY LAW ENFORCEMENT
SUPER SELECT FIRE (SSF®) M4 CARBINE $450
SUPER SELECT FIRE (SSF®) HK416 $450
SUPER SELECT FIRE (SSF®) HK417 $470
MSRP
GEISSELE
LOW
ER PARTSSOPMODCERTIFIED
INTENDED APPLICATION
GEISSELE 2 STAGE (G2S) The Geissele 2 Stage was designed to be a high quality, cost effective alternative to the
SSA. The G2S is a 4.5 lb. non-adjustable precision combat two-stage trigger and allows
precise and accurate trigger control. The G2S is manufactured from the same tool steel
as the SSA. Visually from the outside of the weapon there is no difference from the SSA
and the feel and reliability is the same. The G2S however has a different way of holding
the hammer pin in place, and there are no laser markings.
TARGET HUNTING
G2S
GEISSELE 2 STAGE (G2S) $165
MSRP
GEISSELE
LOW
ER PARTS
SUPER ACRThe Geissele Super ACR offers improved Bushmaster ACR weapon system performance
with a trigger similar in feel and operation to the Geissele Automatics Super
Semi-Automatic trigger. The Super ACR was designed to operate with the Bushmaster
Super ACR plastic safety selector. The Super ACR has a total pull weight of
approximately 4.5 lbs. with a first stage weight of approximately 2.5 lbs. and a second
stage weight of approximately 2.0 lbs. Users must follow all Bushmaster removal and
installation instructions when installing the Geissele Automatics Super ACR trigger.
MILITARY LAW ENFORCEMENT
HUNTING
INTENDED APPLICATION
GEISSELE SUPER ACR $240
MSRP
SUPER ACR G
EISSELE LO
WER PARTS
The Geissele Super Sabra is an advanced drop in replacement for the OEM IWI
Tavor / X95 trigger pack. The Super Sabra’s two-stage design allows the trigger to be
light enough for accurate and precise shots, but forgiving enough for Close Quarters
Battle (CQB). The Geissele Super Sabra also features an adjustable first stage, which will
allow the shooter the ability to fine tune the first and second stage weight distribution.
The Super Sabra’s housing is precision CNC machined from 6061-T6 Aluminum and
Type 3 hardcoat anodized for a long lasting and durable finish. Internal components
are constructed of shock and wear resistant S7 tool steel and a precision wire EDM
process produces razor sharp and polished sear surfaces. A nitride process finish on
the internal components gives further abrasion and corrosion resistance to this must
have upgrade to the industry leading Tavor and X95 bullpup rifles.
SUPER SABRA TRIGGER PACK
SUPER SABRA TRIGGER PACK $350
MSRP
INTENDED APPLICATION
TARGET PRECISIONHUNTING
SUPER SABRA TRIGGER PACK
GEISSELE
LOW
ER PARTS
SUPER SABRA LIGHTNING BOW®
The Super Sabra Lightning Bow® Trigger is precision machined from precipitation
hardening 17-4 stainless steel and is designed to replace the standard trigger in IWI
Tavor and X95 rifles. Once installed, the Sabra Lightning Bow is adjustable via a set
screw that removes the “slack” that is inherently found in the trigger mechanism of
those rifles. By removing the slack, the trigger pull is instantly transformed into a feel
that is much more similar to that of an M4 Carbine. Pairing the Sabra Lightning Bow
with a Super Sabra Trigger Pack will result in a pull that is truly two stage and has a
match grade feel.
INTENDED APPLICATION
TARGET PRECISIONHUNTING
SUPER SABRA LIGHTNING BOW® $99
MSRP
SUPER SABRA LIGHTNING BOW®
GEISSELE
LOW
ER PARTS
1st Stage 2nd Stage Total
1.5 - 2.5 lbs. 6.0 - 14 oz. 1.9 - 3.4 lbs.
MATCH RIFLE PULL WEIGHTS
1st Stage 2nd Stage Total
2.5 - 3.6 lbs. 0.5 - 1.5 lbs. 3.0 - 5.1 lbs.
DMR RIFLE PULL WEIGHTS
1st Stage 2nd Stage Total
3.2 - 5 lbs. 0.5 - 1.5 lbs. 4.5 lbs. Min.
SERVICE RIFLE PULL WEIGHTS
HI-SPEED NATIONAL MATCH The Geissele Hi-Speed Trigger is our premium competition trigger offering. These
adjustable triggers are specially designed for competition, hunting and tactical snipers
where the configuration of the trigger pull is essential to mission success. As an
adjustable trigger, the first and second stage weight distribution, as well as total pull
weight, over-travel, and sear engagement are all tunable to the shooter’s preference.
It features an industry leading 4ms lock time, balanced hammer for a smoother firing
pin strike, full power hammer spring and a forward placed trigger bow. The Hi-Speed
can be set up with the included accessory springs for Match, DMR or Service Rifle
configurations, and is approved for use in CMP High Power Service Rifle competition.
INTENDED APPLICATION
PRECISION
HI-SPEED NATIONAL MATCH $279
MSRP
TARGET HUNTING
NATIONAL MATCH
HI- SPEED NATIONAL MATCH G
EISSELE LO
WER PARTS
MARITIME BOLT CATCH The Geissele Maritime Bolt Catch is designed with the warfighter in mind and will work
with any lower receiver designed to accept a mil-spec M16/M4 Carbine bolt catch.
The increased surface area promotes ease of function when locking back the bolt or
releasing the bolt after a magazine change. In addition, the extended controls add
an increased functionality for left handed shooters who no longer have to break their
grip to manipulate the bolt catch. Left handed shooters can easily reach the controls
using the index finger of their left hand making magazine changes and locking the
bolt back much faster and efficient. Aggressive checkering covers the surface of the
levers giving the Geissele Maritime Bolt Catch a textured surface that enables positive
feedback to the shooter’s hand when being used with gloves or at night. Manufactured
from properly heat treated 8620 steel and manganese phosphate coated, the Geissele
Maritime Bolt Catch is intended to serve as an enhanced mil-spec replacement and
assist in giving our warfighters a more efficient manual of arms with the M16/M4
carbine platform.
MARITIME BOLT CATCH $29
MSRP
GEISSELE
LOW
ER PARTS
SUPER 42 BRAIDED WIRE BUFFER SPRING AND BUFFER COMBO The Geissele Super 42 Spring was designed to improve the function and reliability of
your AR-15 pattern rifle. Its unique spring design uses three independent strands of
wire, just like the German MG42 Machine Gun. This concept acts as a harmonic damper
and energy absorber by allowing the springs to flex separately from each other. This
flex helps displace excess energy which decreases the chance of spring failure and
assists with making your AR-15 more reliable.
Compared to the stock spring, The Geissele Super 42 Spring has a decreased tendency
to lose length and force over a given round count. As an added bonus, it removes
the annoying spring reverberations (twang) heard and felt by the shooter through
the buttstock. The Super 42 Spring has a 15% stronger average return force than the
standard buffer spring. This will assist in stripping rounds out of the magazine when
operating with a dirty weapon or when using steel-case ammo.
SUPER 42 BRAIDED WIRE BUFFER SPRING AND BUFFER COMBO $65
ADDITIONAL TUNGSTEN BUFFER WEIGHT $20 EACH
MSRP
GEISSELE
LOW
ER PARTS
SUPER MODULAR RAILSEach Super Modular Rail (SMR) adheres to a strict set of design guidelines that we have learned over the years of manufacturing superior battle
proven rail systems. Each SMR is designed to be ergonomic, modular and flexible. A rail must be comfortable for the shooter, it is vital that the
interface between shooter and the rail system feels natural. The level of comfort found in the SMR family of rails, promotes confidence and frees
the shooter’s mind of worry when faced with hitting a target. The rail set up must be able to be customizable by the shooter for the same reason.
The shooter must be able to place accessories, optics, grips, lights, lasers and other mission essential equipment needed for the task at hand.
While meeting the needs of the most demanding shooters, a rail must also be strong, rigid, light weight and free floating . To do this we utilize
a large proprietary 2 ¼” barrel nut made from 7075-T6 aircraft grade aluminum. This is the solid platform by which the rail interfaces with the
upper receiver. The length of the Geissele barrel nut design promotes extreme stiffness and will aid in minimizing bore and rail deflection as
much as possible, critical for use with IR laser aiming devices. This also allows the system to be easily removed and reinstalled for maintenance
and cleaning while maintaining zero of its attached accessories. The rail itself is machined from 6061-T6 aircraft grade aluminum. Every inch
of the SMR is touched with a tool, and is machined completely from a single piece of material. There are no glued or screwed together parts.
The SMR has an excellent performance to weight ratio. Balance is as important as weight, therefore the center of gravity of the rail is biased
toward the receiver for good weapon handling characteristics.
Most Geissele SMR’s also feature Magpul’s® M-LOKTM attachment technology. The M-LOK interface creates a very strong platform by which
accessories may be attached to the SMR. M-LOK stands for Modular Lock system. The M-LOK system retains an elongated slot appearance,
similar to MOE slots (with different dimensions). The new slot is larger, has squared sides, and the new system adds the following feature
set; direct mount capability, cammed steel t-nut design, recoil/impact mitigation sheer lugs, intermediate spacing option, multi-directional
mounting, and backwards MOE compatibility.
SUPER MODULAR RAIL MK4 M-LOK™ The Super Modular Rail (SMR) MK4 M-LOK™ is Geissele’s ultra-combat M-LOK option.
These rails are purpose-built and feature integrated M1913 picatinny rail sections at
the fore end of the rail in the 3, 6 and 9 o’clock positions. Maximum venting for heat
dissipation also dramatically reduces the rail’s overall weight, while maintaining its
same strong and rigid platform.
Utilizing Magpul’s M-LOK technology at the 3, 6, and 9 o’clock positions, as well as the
upper 45° quadrants, the SMR MK4 is both versatile and modular, allowing the user to
tailor their platform to his or her unique needs.
The SMR MK4 also features Geissele’s proprietary 2¼” long barrel nut. This increases
the surface contact where the rail interfaces with the receiver and creates a platform
that can be trusted to be straight and true the entire length of the free float rail. This
increases accuracy and zero repeatability during disassembly and reassembly when
performing maintenance.
7” MK4, BLACK $225 7” MK4, DDC $250
9.5” MK4, BLACK $250 9.5” MK4, DDC $275
13” MK4, BLACK $275 13” MK4, DDC $300
15” MK4, BLACK $300 15” MK4, DDC $325
MSRP
RAIL INCLUSIONS: STAINLESS STEEL GAS BLOCK ($59 VALUE) ;
BARREL NUT; BARREL NUT WRENCH; BARREL NUT BOLTS; HEX KEYS
GEISSELE
UPPER PARTS
SUPER MODULAR RAIL MK8 M-LOK™ The Super Modular Rail (SMR) MK8 M-LOK™ is Geissele’s ultra-modular model. The
SMR MK8 is one of the first rails available to utilize the Magpul M-LOK technology.
These rails are designed to give the user full modularity while maintaining a strong and
rigid platform. Maximum venting at the lower 45° quadrants create maximum heat
dissipation and also dramatically reduces the rail’s overall weight.
Utilizing Magpul’s M-LOK technology at the 3, 6, and 9 o’clock positions, as well as the
upper 45° quadrants, the SMR MK8 is both versatile and modular, allowing the user to
tailor their platform to his or her unique needs.
The SMR MK8 also features Geissele’s proprietary 2¼” long barrel nut. This increases
the surface contact where the rail interfaces with the receiver and creates a platform
that can be trusted to be straight and true the entire length of the free float rail. This
increases accuracy and zero repeatability during disassembly and reassembly when
performing maintenance.
7” MK8, BLACK $225 7” MK8, DDC $250
9.5” MK8, BLACK $250 9.5” MK8, DDC $275
13” MK8, BLACK $275 13” MK8, DDC $300
15” MK8, BLACK $300 15” MK8, DDC $325
MSRP
RAIL INCLUSIONS: STAINLESS STEEL GAS BLOCK ($59 VALUE) ;
BARREL NUT; BARREL NUT WRENCH; BARREL NUT BOLTS; HEX KEYS
GEISSELE
UPPER PARTS
SUPER MODULAR RAIL MK7 NATIONAL MATCH The Super Modular Rail MK7 is the first CMP-legal rail system that was designed
specifically for National Match High Power Competition. The MK7 features a full quad
rail, with the sling loop in its appropriate legal location for competition. The sling loop
is attached to a steel bar which is fastened directly to the rail using screws to increase
weight. Along with the rail system, lead weight bars can be purchased separately and
fastened in the 3 and 9 o’clock positions to add weight as needed to balance the rifle
per the shooter’s preference.
The weights and sling bar can also be modified per the user to have any undesired
excess weight trimmed off and reinstalled. The rail system is completely free floating
and is mounted to the weapon platform via Geissele’s rock solid 2 ¼” barrel nut design.
12.7” MK7, BLACK $375
12.7” MK7, DDC $400
LEAD SIDE WEIGHTS $25 EACH
MSRP
RAIL INCLUSIONS: BARREL NUT, BARREL NUT WRENCH,
BARREL NUT BOLTS, SLING BAR / SLING LOOP, SLING SCREWS, HEX KEYS
GEISSELE
UPPER PARTS
SUPER MODULAR RAIL MK13 M-LOK™ The MK13 is the latest entry to the Geissele line up of Super Modular Rails. The new
handguard design offers a smaller diameter and overall height to create a slimmer
package. Included with the MK13 Super Modular Rail is an updated version of the
proven Geissele Barrel Nut design, not only providing ease of installation but superior
rigidity. The long surface contact of the 2¼” barrel nut interfaces with the receiver
creating a platform that can be trusted to be straight and true the entire length of
the free float rail. The MK13 is precision machined using 6061-T6 aluminum due to its
strength, rigidity and lightweight properties.
Utilizing Magpul’s M-LOK technology in the 3, 6, and 9 o’clock positions and machined-
in Picatinny rails at the fore-end allow the end user to customize their rifle and securely
mount lights, bipods and other firearm accessories. The Geissele MK13 Super Modular
Rail is finished in a durable and long lasting Type 3 Hardcoat Anodize available in
either Black or Geissele’s DDC finish.
RAIL INCLUSIONS: STAINLESS STEEL GAS BLOCK ($59 VALUE) ;
BARREL NUT; BARREL NUT WRENCH; BARREL NUT BOLTS; HEX KEYS
7” MK13, BLACK $250 7” MK13, DDC $275
9.5” MK13, BLACK $250 9.5” MK13, DDC $275
13” MK13, BLACK $250 13” MK13, DDC $275
15” MK13, BLACK $300 15” MK13, DDC $325
MSRP
GEISSELE
UPPER PARTS
SUPER MODULAR RAIL MK14 M-LOK™ The MK14 is the latest entry to the Geissele line up of Super Modular Rails. The new
handguard design offers a smaller diameter and overall height to create a slimmer
package. Included with the MK14 Super Modular Rail is an updated version of the
proven Geissele Barrel Nut design, not only providing ease of installation but superior
rigidity. The long surface contact of the 2¼” barrel nut interfaces with the receiver
creating a platform that can be trusted to be straight and true the entire length of the
free float rail. The MK14 is 3D precision machined using 6061-T6 Aluminum due to its
strong, rigid and lightweight properties.
Utilizing Magpul’s M-LOK technology in the 3, 6, and 9 o’clock positions allow the end
user full customization and modularity of their rifle to securely mount lights, bipods
and other firearm accessories. The Geissele MK14 Super Modular Rail is finished
in a durable and long lasting Type 3 Hardcoat Anodize available in either Black or
Geissele’s DDC finish.
RAIL INCLUSIONS: STAINLESS STEEL GAS BLOCK ($59 VALUE) ;
BARREL NUT; BARREL NUT WRENCH; BARREL NUT BOLTS; HEX KEYS
7” MK14, BLACK $250 7” MK14, DDC $275
9.5” MK14, BLACK $250 9.5” MK14, DDC $275
13” MK14, BLACK $250 13” MK14, DDC $275
15” MK14, BLACK $300 15” MK14, DDC $325
MSRP
GEISSELE
UPPER PARTS
SUPER GAS BLOCK The Geissele Super Gas Block (SGB) is a low profile gas block designed to fit under most free float rails. It has the following features:• Precision investment cast from 17-4 Precipitation Hardening Stainless Steel.• Corrosion resistant to withstand corrosive powder residue• Lightweight at 1.6 oz.• The .750” diameter bore is precisely machined for a close slip fit onto the
barrel.• Set screws are used to secure the SGB to the rifle barrel. Additionally, the
Nitride SGB is pre-drilled for a 3/16” spiral coil pin so the SGB can be secured in a fool proof manner to the rifle barrel.
SUPER GAS BLOCK, STAINLESS STEEL $59
SUPER GAS BLOCK, NITRIDE $69
MSRP
GEISSELE
UPPER PARTS
SUPER PRECISION OPTIC MOUNTSA U.S. Special Operations customer asked Geissele to make them an ultra high quality, bomb proof scope
mounting system that met their mission critical return to zero requirements. The Geissele Super Precision Series
of optic mounts were designed to meet their requirement and become the finest military sniper scope mounts.
Machined from a single 4.5 lb. block of aircraft grade 7075 -T6 billet aluminum, the Super Precision Scope
Mount is milled down to an ultra light 7.2 ounces. Geissele Super Precision Scope Mounts feature four shear
lugs precision machined to the minimum tolerance of the MIL-STD-1913 Picatinny slot so that the optic stays in
place from recoil and bolt carrier counter recoil.
The individually serialized scope caps are line bored with the body and created in a single operation, creating
the best possible fit to the body of the optic so that the scope caps can be tightened without fear of crushing
the body of the optic. The Geissele mounts are locked in place utilizing the classic, battle proven nut and clamp
system which provides 1,400 lbs. of clamping force per nut. This system provides more clamping force than any
inferior lever system ever could.
SUPER PRECISION™ STANDARD LENGTH
SUPER PRECISION™ EXTENDED LENGTH
SUPER PRECISION, 30MM STANDARD LENGTH, BLACK $325
SUPER PRECISION, 30MM STANDARD LENGTH, DDC $350
SUPER PRECISION, 34MM STANDARD LENGTH, BLACK $325
SUPER PRECISION, 34MM STANDARD LENGTH, DDC $350
MSRP
STANDARD
EX TENDED
MSRPSUPER PRECISION, 30MM EXTENDED LENGTH, BLACK $325
SUPER PRECISION, 30MM EXTENDED LENGTH, DDC $350
SUPER PRECISION, 34MM EXTENDED LENGTH, BLACK $325
SUPER PRECISION, 34MM EXTENDED LENGTH, DDC $350
GEISSELE
UPPER PARTSSUPER PRECISION™ HYPER EXTENDED LENGTH
SUPER PRECISION™ 1.93” HEIGHT
HYPER EX TENDED
1.93” HEIGHT
GEISSELE
UPPER PARTS
MSRPSUPER PRECISION, 30MM HYPER EXTENDED LENGTH, BLACK $325
SUPER PRECISION, 30MM HYPER EXTENDED LENGTH, DDC $350
SUPER PRECISION, 34MM HYPER EXTENDED LENGTH, BLACK $325
SUPER PRECISION, 34MM HYPER EXTENDED LENGTH, DDC $350
SUPER PRECISION, 30MM 1.93” HEIGHT, BLACK $325
SUPER PRECISION, 30MM 1.93” HEIGHT, DDC $350
MSRP
SUPER PRECISION™ SOPMOD CERTIFIED LEUPOLD CQBSS OPTIC MOUNT
SUPER PRECISION™ SOPMOD CERTIFIED LEUPOLD MARK 6 OPTIC MOUNT
LEUPOLD CQBSS OPTIC MOUNT, 34MM FOR SR-25, BLACK $325
LEUPOLD CQBSS OPTIC MOUNT, 34MM FOR SR-25, DDC $350
MSRP
LEUPOLD MARK 6 OPTIC MOUNT, 34MM FOR SR-25, BLACK $325
LEUPOLD MARK 6 OPTIC MOUNT, 34MM FOR SR-25, DDC $350
MSRP
LEUPOLD CQBSS OPTIC MOUNT
LEUPOLD MARK 6 OPTIC MOUNT
SUPER PRECISION™ SOPMOD CERTIFIED VORTEX 1-6 OPTIC MOUNT
SUPER PRECISION™ SOPMOD CERTIFIED SCHMIDT & BENDER OPTIC MOUNT
SCHMIDT & BENDER OPTIC MOUNT, 34MM FOR SR-25, BLACK $325
SCHMIDT & BENDER OPTIC MOUNT, 34MM FOR SR-25, DDC $350
MSRP
VORTEX 1-6 OPTIC MOUNT, 30MM FOR AR-15, BLACK $325
VORTEX 1-6 OPTIC MOUNT, 30MM FOR AR-15, DDC $350
MSRP
SCHMIDT & BENDER OPTIC MOUNT
VORTEX 1-6OPTIC MOUNT
GEISSELE
UPPER PARTSSOPMODCERTIFIED
SUPER PRECISION™ T1 SERIES The Super Precision T1 Series was developed specifically to work with the Aimpoint T1
and similarly mounted red dot optics. These mounts are precision machined from a
single piece of 7075-T6 high strength aluminum and are available in absolute, lower
third co-witness and 1.93” height options.
Utilizing Geissele’s update of the classic nut and bolt method, this mount will attach
your red dot to your weapon with 1,400 lbs. of clamping force, and features 3 shear
lugs for maximum rigidity and return to zero.
T1 OPTIC MOUNT, ABSOLUTE CO-WITNESS, BLACK $95
T1 OPTIC MOUNT, ABSOLUTE CO-WITNESS, DDC $120
T1 OPTIC MOUNT, LOWER 1/3 CO-WITNESS, BLACK $95
T1 OPTIC MOUNT, LOWER 1/3 CO-WITNESS, DDC $120
T1 OPTIC MOUNT, 1.93” HEIGHT, BLACK $95
T1 OPTIC MOUNT, 1.93” HEIGHT, DDC $120
MSRP
GEISSELE
UPPER PARTS
SUPER PRECISION™ MRO SERIES The Super Precision MRO Series was developed specifically to work with the Trijicon
MRO and like mounted red dot optics. These mounts are precision machined from a
single piece of 7075-T6 high strength aluminum and are available in absolute, lower
third co-witness and 1.93” height options.
Utilizing Geissele’s update of the classic nut and bolt method, this mount will attach
your red dot to your weapon with 1,400 lbs. of clamping force, and features 3 shear
lugs for maximum rigidity and return to zero.
MRO OPTIC MOUNT, ABSOLUTE CO-WITNESS, BLACK $95
MRO OPTIC MOUNT, ABSOLUTE CO-WITNESS DDC $120
MRO OPTIC MOUNT, LOWER 1/3 CO-WITNESS, BLACK $95
MRO OPTIC MOUNT, LOWER 1/3 CO-WITNESS, DDC $120
MRO OPTIC MOUNT, 1.93” HEIGHT, BLACK $95
MRO OPTIC MOUNT, 1.93” HEIGHT, DDC $120
MSRP
GEISSELE
UPPER PARTS
SUPER PRECISION™ ACOG SERIES The Super Precision ACOG Series was developed specifically to work with the Trijicon 4x
power ACOG series of optics. These mounts are precision machined from a single piece
of 7075-T6 high strength aluminum.
They are available in black type 3 Hardcoat Anodize as well as our proprietary DDC
(Desert Dirt Color) type 3 Hardcoat Anodize. Utilizing Geissele’s update of the classic
nut and bolt method, this mount will attach your ACOG to your weapon with 2,800 lbs.
of clamping force, and features 4 shear lugs for maximum rigidity and return to zero.
ACOG OPTIC MOUNT, BLACK $125
ACOG OPTIC MOUNT, DDC $150
MSRP
GEISSELE
UPPER PARTS
GEISSELE CHARGING HANDLESThe Super Charging Handle (SCH®) is 3D machined from a solid block of aircraft grade 7075-T6 aluminum.
Its ambidextrous design allows for seamless operation from either side of the weapon. The levers are dual
contoured similar to that of the charging handle of an M14, where not only the x-axis but also the y-axis
receive radius cuts.
The handling surface of the lever is also checkered adding a textured grip to aid in use when operating with
gloves. The heightened rear lip of the SCH helps in mitigating gas blow back to the shooter when shooting
with short barreled and suppressed weapon systems.
All parts are Type 3 Hardcoat Anodized and are available in Black and DDC (Desert Dirt Color) .
5.56 SUPER CHARGING HANDLE (SCH®)
7.62 SUPER CHARGING HANDLE (SCH®)
HK417 SUPER CHARGING HANDLE (SCH®)
5.56 SUPER CHARGING HANDLE (SCH), BLACK $89
5.56 SUPER CHARGING HANDLE (SCH), DDC $99
7.62 SUPER CHARGING HANDLE (SCH), BLACK $125
7.62 SUPER CHARGING HANDLE (SCH), DDC $135
HK417 SUPER CHARGING HANDLE (SCH), BLACK $145
HK417 SUPER CHARGING HANDLE (SCH), DDC $155
MSRP
MSRP
MSRP
GEISSELE
UPPER PARTSAIRBORNE CHARGING HANDLE (ACH®)
MCX SUPER CHARGING HANDLE (SCH®)
MPX SUPER CHARGING HANDLE (SCH®)
AIRBORNE SUPER CHARGING HANDLE (ACH), BLACK $89
AIRBORNE SUPER CHARGING HANDLE (ACH), DDC $99
MCX SUPER CHARGING HANDLE (SCH), BLACK $119
MCX SUPER CHARGING HANDLE (SCH), DDC $129
MPX SUPER CHARGING HANDLE (SCH), BLACK $119
MPX SUPER CHARGING HANDLE (SCH), DDC $129
MSRP
MSRP
MSRP
ARMORER’S TOOLSGeissele prides itself on not just being a premier manufacturer of weapon components, but also a premier
manufacturer of armorer’s tools. Each one of our tools was developed and manufactured for a specific purpose,
driven from challenges encountered in daily life when routinely working on your AR-15. We are always looking
for new ways to increase ease and efficiency when building a new rifle, performing maintenance on or cleaning
an existing rifle, or simply installing that new product that will enhance your weapon’s capability. Our goal is to
provide top quality tools to everyone from the weekend warrior to the everyday armorer so that you can spend
more time behind the trigger than behind the work bench.
GAS BLOCK ACCESSORIES The Gas Block Roll Pin Tool is designed to securely hold a 0.078” diameter roll pin to start the pin installation in a gas block. The hole in the tip of the tool is sized so that the roll pin will need to be pressed into the tool first (the roll pin will not just slide in). Stand the roll pin on a hard surface and tap the tool onto the pin to seat it in the tool. When the hole in the gas block grabs the roll pin, the pin will collapse enough so the tool can be removed from the roll pin. All that is needed then is a tap with a punch to seat the roll pin in the gas block.
The Geissele Gas Block Pin Punches are specially made for removing and installing the 0.078” roll pin that secures the gas tube to the gas block on an M4 Carbine/AR10.The removal of a rusted-in gas block roll pin has always been a challenge since there are no commercial pin punches in 0.078” diameter. 1/16” (0.062”) punches have a tendency to bend and very few starter punches are available in 1/16” diameter.
The Geissele punches make gas block work a whole lot easier. The first punch to use when removing the roll pin is the Starter Punch. This is the punch with the long tapered end. The long taper is much more resistant to bending and buckling than the straight shank of the Pin Punch. Use the Starter Punch to just get the roll pin moving. Then use the Pin Punch to drive the roll pin fully out. The Geissele Gas Block punches are made from properly hardened and tempered O1 tool steel.
GEISSELE TO
OLS
MSRPROLL PIN TOOL $12.50
PIN PUNCH KIT $25
TRIGGER FITTING PIN The Geissele Trigger Fitting Pin is a tool designed to help with small pin hammer and
trigger installations. The tool is sized to match the size of the pins and may be slipped
into the receiver to act as a slave pin to help ease the installation of the new pins
supplied with every Geissele AR-15 trigger.
TRIGGER FITTING PIN $15
MSRP
GEISSELE TO
OLS
REACTION RODThe Geissele Reaction Rod is a tool that securely holds an upper receiver assembly
for maintenance and assembly work. It will make working on an AR15/M4 or AR10/
SR25 a dream. The removal and installation of barrels, flash hiders, gas blocks
and hand guards is made much easier. The Reaction Rod is designed to be gripped
in a bench vise so that the rod is either horizontal or vertical. The upper receiver is
then slid onto the rod and the rod’s integral splines enter the barrel extension and
secure the barrel extension from turning. This allows all of the torque from barrel
nut wrenches to go directly into the barrel extension. In contrast, receiver vise
blocks transmit the turning force into the aluminum receiver, a good part of which
passes through the small, easily distorted receiver index pin. With the Geissele
Reaction Rod, marring of an upper receiver’s finish by gripping and twisting inside
vise blocks is eliminated and so is the need to remove sights and mounts from the
receiver’s M1913 rail.
AR-15/M4 REACTION ROD $99
AR-10/SR-25 REACTION ROD $199
MSRP
SUPER REACTION RODGeissele’s Super Reaction Rod was designed with the advanced armorer in mind,
an armorer who frequently works on AR15/M4 platforms with over torqued, seized
or Loctited barrel nuts. The Super Reaction Rod works by pre-loading the barrel nut
extension to the lugs of the Super Reaction Rod to eliminate any movement before
adding torque to the barrel nut, while at the same time fixing the upper receiver into
place. Having the barrel nut extension mated to the Super Reaction Rod lugs and fixing
the upper receiver before torqueing will remove any potential stress that could be
placed on the index pin. This allows the armorer to place tremendous torque on the
barrel nut. The Super Reaction Rod’s pre-loading system can also be removed to allow
it to work just like a standard Reaction Rod, which allows upper work to be performed
in 360° both vertically and horizontally.
MSRPAR-15/M4 SUPER REACTION ROD $175
GEISSELE TO
OLS
REACTION BLOCK The Geissele Reaction Block is designed to aid in the assembly of lower receivers. Once
the armorer has installed the buffer tube, the lower receiver can then be slid into the
Reaction Block at the 12, 3, 6 and 9 o’clock positions. The block allows the armorer
to rotate the lower in 90° increments simply by loosening the provided nylon screws,
removing the lower and sliding it back in at its desired orientation. The Reaction Block
provides an ultra-stable platform for performing an array of lower receiver operations,
as well as making the installation of the buffer retainer nut quick and easy. All while
keeping both hands of the armorer free to work, saving both time and frustration.
REACTION BLOCK $99
MSRP
GEISSELE TO
OLS
SUPPRESSOR ALIGNMENT GAGE The Geissele Suppressor Alignment Gage (SAG) is a precision gage used to verify the
alignment of a suppressor to the bore of a firearm barrel.
It is important to understand that the length of the suppressor is usually much longer
than the length of the barrel / muzzle device / suppressor interface geometry. A small
deviation at the mounting interface means a much larger deviation of the suppressor
exit hole. The deviations from nominal can also be additive which compounds
suppressor misalignment. The Geissele SAG is manufactured from hardened steel that
has been ground 0.002” under nominal bore diameter. The outside diameter of the
SAG is finely finished and straight to 0.001” over its length.
Geissele hardens the SAG so that it will not wear by sliding exposure to abrasive powder
residue, pull burrs if it slides against misaligned baffles, nor allow abrasive particles
to embed into the surface of the gage. There can be a wide variation in barrel bore
diameters and bore straightness. 0.002” under nominal bore diameter has been found
to be the best size of the SAG that will fit most barrels. The long length of the SAG
aligns the gage to the bore; it is not necessary to have a very tight fitting gage with the
long length of the Geissele SAG.
15” 5.56MM SUPPRESSOR ALIGNMENT GAGE $75
17” 7.62MM SUPPRESSOR ALIGNMENT GAGE $75
MSRP
GEISSELE TO
OLS
ALG DEFENSE
QUALITY MIL-SPEC TRIGGER (QMS) The ALG Defense Quality Mil-Spec Trigger is designed to provide an affordable
improvement for the AR-15 rifles. The pull of the QMS is very similar to a standard
mil-spec trigger, however the majority of the associated grittiness of the stock trigger
pull has been removed while the well known reliability of a stock trigger remains. The
pull weight is not lower than the M4/M16 minimum weight specification of 5.5 lbs.
Generally, the pull weight is around 6.5 lbs.
QUALITY MIL-SPEC TRIGGER (QMS) $49
MSRP
ALG
LOW
ER PARTS
ADVANCED COMBAT TRIGGER (ACT)The ALG Defense Advanced Combat Trigger is very similar to a standard mil-spec
trigger. Just like the QMS, The ACT is sharper and the grittiness of the stock trigger
pull has been removed while the traditional reliability of a stock trigger remains.
The ACT is Nickel Teflon and Nickel Boron processed and the polished sears have
been hard lubed to create a permanent lubricated surface for a consistently
smooth pull.
The ALG purple hammer spring comes installed on the ACT hammer providing an
approximate pull weight of 4.5 lbs. This spring is perfect for individuals using their rifle
for recreational purposes or target shooting. Also, a tan hammer spring is included to
provide an approximate pull weight of 6.0 lbs. which meets the minimum pull weight of
5.5 lbs. in the M4 Carbine specifications.
ADVANCED COMBAT TRIGGER (ACT) $69
MSRP
ALG
LOW
ER PARTS
AK TRIGGERS The AKT-Enhanced with Lightning Bow (AKT-EL) features a smoother and shorter
trigger pull than the stock trigger and is ideal for combat and home defense use. It has
a Manganese Phosphate finish which is the same process used on stock AK triggers.
The AKT-Ultimate with Lightning Bow (AKT-UL) features a pull that is even lighter and
has a much crisper break which is ideal for precision and target shooting.
The AKT-EL and AKT-UL both feature a unique trigger bow known as the Lightning Bow,
which produces a very comfortable feel to the user over the stock trigger.
AKT-ENHANCED W/ LIGHTNING BOW (AKT-EL) $65
AKT-ULTIMATE W/ LIGHTNING BOW (AKT-UL) $90
MSRP
ALG
LOW
ER PARTS
GALIL TRIGGER AGT-UL The ALG Galil Trigger–Ultimate with Lightning Bow (AGT-UL) is a single stage trigger
based on the AKT-UL and designed for the IWI Galil Ace rifle and pistol platform.
The AGT-UL is machined from gun quality alloy steel and utilizes a Lightning Bow.
The AKT-UL features a smooth trigger that is shorter and crisper than the stock
two-stage trigger. This design is ideal for precision and target shooting. The
recommended pull weight of the AGT-UL is approximately 3.5 lbs.
ALG GALIL TRIGGER W/ LIGHNING BOW (AGT-UL) $95
MSRP
ALG
LOW
ER PARTS
ALG DEFENSE SPRINGS The AK Braided Main Spring is a replacement spring for the AK47/74
platform rifles. This replacement option is manufactured in the United
States from three strands of music wire braided together.
The AK High Energy Main Spring is a performance replacement spring for
the AK47/74 platform rifles. It is a chrome silicon single wire spring fabricated
per ASTM A401 specifications. The ALG High Energy Main Spring develops
25% more torque over a standard factory main spring, lowering lock time and
also increasing the consistency of primer ignition.
ALG’s AK Recoil Spring is a one of a kind design, it is manufactured from chrome
silicon steel which resists impact shock and relaxation. The 2 to 3 dead coils in the
center change the natural frequency of the spring, which prevents harmonics from
damaging the spring and reducing its free length.
AK Braided Main Spring $9
AK High Energy Main Spring $9.50
AK Recoil Spring $12
MSRP
ALG
LOW
ER PARTS
ALG UPPER PARTS
ERGONOMIC MODULAR RAIL EMR V2 M-LOKThe Ergonomic Modular Rail V2 with Magpul M-LOK support allows the user to mount
an array of third party accessories and customize their weapon platform to suit their
needs. M-LOK accessories can be attached along the length of the rail at 2, 4, 6, 8 and
10 o’clock positions. The EMR V2 M-LOK also features two integrated anti-rotational
QD slots at the base of the rail at the 2 and 10 o’clock positions.
The EMR V2 has a machined M1913 picatinny rail section at the muzzle end of the
rail at the 12 o’clock position. The machined M1913 section is ideal for attaching
front sights, lasers, IR illuminators, lights and any other optic or sling related M1913
compatible accessory.
10” BLACK EMR V2 HANDGUARD $145
13” BLACK EMR V2 HANDGUARD $155
15” BLACK EMR V2 HANDGUARD $165
DDC AVAILABLE ADD $15
MSRP
ALG
UPPER PARTS
ERGONOMIC MODULAR RAIL EMR V3 M-LOK Like the V2, the V3 M-LOK support allows the user to mount an array of third party
accessories and customize their weapon platform to suit their needs. Magpul M-LOK
accessories can be attached along the length of the rail at 2, 4, 6, 8 and 10 o’clock
positions.
The EMR V3 M-LOK also features two integrated anti-rotational QD slots at the base
of the rail at the 2 and 10 o’clock positions. The primary difference of the EMR V3 is
its full-length M1913 picatinny rail at the 12 o’clock position. The machined M1913
section is ideal for attaching front sights, lasers, IR illuminators, lights and any other
optic or sling related M1913 compatible accessory.
10” BLACK EMR V3 HANDGUARD $145
13” BLACK EMR V3 HANDGUARD $155
15” BLACK EMR V3 HANDGUARD $165
DDC AVAILABLE ADD $15
MSRP
ALG
UPPER PARTS
FORGED SLING SWIVEL (FSS) The ALG Forged QD Sling Swivel is a lightweight but heavy-duty sling swivel option.
The standard QD configuration makes it compatible with any device that accepts QD
accessories. The FSS weighs in at roughly 0.4 ounces and is about half the weight of
similar steel QD sling swivel assemblies. The FSS is forged from 7075-T6 aluminum,
which is the same aluminum typically used to make upper and lower receivers. This
process allows the FSS to be very strong and can withstand pull forces of up to 750 lbs.
FORGED SLING SWIVEL, BLACK $32
FORGED SLING SWIVEL, DDC $34
MSRP
ALG
UPPER PARTS
BOLT CARRIER GROUP (BCG)The ALG Mil-Spec Bolt Carrier Group (BCG) is a great replacement or backup for your
current AR, or a perfect starting point for your next build. The Bolt is CNC ground after
heat treat for true Mil Spec dimensions and fit. Made of case hardened 9310 steel,
shot peened, and ships with the Crane O-Ring installed. Our bolts are High Pressure
Tested (HPT) and Magnetic Particle Inspected (MPI).
The Carrier is made of 8620 steel, the gas key is 4130 steel and is attached with Grade
8 hardware and properly staked. The ALG Phosphate BCG is compatible with AR15
rifles chambered in .223/5.56, .300 Blackout, and 6.8 SPC.
BOLT CARRIER GROUP, PHOSPHATE $140
BOLT CARRIER GROUP, BLACK NITRIDE $160
MSRP
ALG
UPPER PARTS
ALG GLOCK ACCESSORIES
6-SECOND MOUNTS 6SM The ALG Defense 6-Second Mount was designed when a counter-terrorism unit
approached ALG with a strict set of criteria. When entering a linear environment,
such as an airplane or bus, the team’s primary weapon was their pistol and they
were looking for a fast sighting method that was rugged and robust. Red dot scopes
mounted directly to their pistol slides were showing a high failure rate due to extreme
acceleration and deceleration of the slide. The balance of the pistols was thrown
off from the rearward scope mounting position, and the slides were weakened from
machining a pocket for the scopes into the top of the slide. The name, 6-Second Mount,
comes from a description used by one of the operators: “The fight lasts 6 seconds...
Either they’re dead or you’re dead, and aggression saves the day.”
The ALG 6-Second Mount is available in two different models to accommodate the
Aimpoint T1 or the Trijicon RMR red dot optics. Mounting an optic to your weapon
decreases engagement time, allowing for faster and more accurate hits on target.
By separating the sight from the reciprocating slide it allows the pistol to function
properly without the added mass of the optic sight, and produces a favorable weight
distribution.
The ALG 6-Second Mount is machined from 6061-T6 aluminum and designed to fit Gen
3 and Gen 4 Glock 17, 22, 24, 31, 34 and 35.
6 SECOND MOUNT FOR T1 / RMR, BLACK $250
AVAILABLE IN DDC, GRAY AND PURPLE $265
MSRP
ALG
GLO
CK ACCESSO
RIES
ALG FLARED MAGWELL (AFM)The ALG Flared Magwells (AFM) are precision machined from billet 6061-T6 aluminum and designed to seamlessly fit Gen 3 and Gen 4 Glock 17, 22, 24, 31, 34 and 35 pistols without modification to the AFM or the frame itself. The Supersonic Gen 4 Magwell will accommodate Glocks without backstraps. The Supersonic Gen 4 Magwell with medium backstrap and Federal versions will accommodate Glocks which utilize medium backstraps. The AFM is finished using a Type 3 Hardcoat Anodize process which allows the AFM to be long lasting and durable.
The AFM allows for rapid reloading of magazines by decreasing the precision required to insert the magazine into the pistol. Additionally, the AFM is designed to allow magazines to freely drop without modification to the pistol or the AFM, which is one of the most common issues found when using aftermarket magwells. The flared design also allows the AFM to act as a ledge to spread the recoil impulse into the bottom of the gripping hand, allowing the user to retain more control of his or her pistol.
Note: Since the AFM is made from aircraft aluminum and hardcoat anodized it should be recognized that it will lightly scratch or scuff the pistol where it comes in contact with the plastic pistol frame.
GEN 3, BLACK $95
GEN 4 NO BACKSTRAP, BLACK $95
GEN 4 W/ MEDIUM BEAVERTRAIL, BLACK $95
GEN 4 FEDERAL W/ MEDIUM BEAVERTAIL, BLACK $95
AVAILABLE IN DDC, GRAY AND PURPLE $105
MSRP
ALG
GLO
CK ACCESSO
RIES
ALG LUBRICANTS
ALG GO-JUICE (GJTM) Engineered specifically for the total-loss, boundary lubrication system that is characteristic
of all firearms, ALG Go-Juice (GJ™) possesses unique properties that will keep your
weapon running in the most adverse conditions.
The most important property of a firearm lubricant is its lubricity or “slickness.” In
comparison to military grade CLP, Go-Juice is 500% more slick as determined by
laboratory tests. Other key characteristics of a good gun lube are corrosion resistance
and long term stability or resistance to breakdown that leads to gumminess and a gun
that won’t function. ALG Go-Juice is made up of highly oxidation resistant molecules that
perform exceptionally well in ALG Defense’s accelerated aging tests and salt spray tests.
As a biosynthetic oil, the fundamental building blocks of Go-Juice’s oil molecule is a GMO
oil seed that has been bred specifically for its lubrication properties. Being an engineered
bio-based oil, ALG Go-Juice needs none of the heavy metals and toxic additives that other
lubricants can use. Therefore, ALG Go-Juice needs no hazardous label and testing on
synthetic human tissue has shown no tendency to even irritate skin.
Perfect for automatic weapons and concealed carry guns, we think that you will find ALG
Go-Juice to be your ultimate “Go To Firearm Lubricant.”
GO-JUICE (GJTM) SAMPLE PACKS (10 PACKS) $10
GO-JUICE (GJTM) 4OZ. BOTTLE $11.50
GO-JUICE (GJTM) CARTON (12 4OZ. BOTTLES) $138
MSRP
ALG GO-JUICE OOOO VERY THIN GREASE ALG Defense’s 0000 VTG meets four important characteristics of a grease type firearm
lubricant: ultra high lubricity, ultra high staynacity*, non-gumming and rust resistance.
The 0000 (Zero, Zero, Zero, Zero) name originated from tests completed on the consistency
of the grease showing that 0000 VTG is thinner than the thinnest commercially available
000 NLGI grease. Ultra high lubricity which is a key characteristic in both Go-Juice and
0000 VTG will make your weapon run in the most adverse conditions without hesitation.
Ultra High Staynacity* means ALG 0000 VTG allows you to evenly apply grease across
the surface without run off. For example, after lubricating a holstered weapon, there will
be no drainage of oil in the bottom of your holster.
ALG 0000 Very Thin Grease is made of oxidation resistant molecules which will prevent
gumming allowing the gun to be stored without fear of it locking up. Also, B117 ASTM salt
spray testing was performed to ensure a corrosion resistant formula.The lubricant stays
in place and will not run off to keep your weapons running in tough conditions, 0000 Very
Thin Grease will be your “Go To Firearm Lubricant.”
*Staynacity Stāˈnasădē / Origin: 2015-2016; Middle Age German Definition: The ability of a lubricant to stay where it’s applied.
GO-JUICE 0000 VTG SAMPLE PACKS (10 PACKS) $12
GO-JUICE 0000 VTG $13.50
GO-JUICE 0000 VTG CARTON (12 4OZ. BOTTLES) $168
MSRP
ALG
LUBRICAN
TS
ABRAHAM & MOSES KNIVESAbraham & Moses Survival Equipment was founded on a young man’s dream. Bill Geissele was reading stories of backwoods adventures and
survival to his son, Abraham. The stories described the age old battle between man and the elements, focusing on the equipment which proved
invaluable to man’s survival. Abraham’s interest and imagination were piqued. “Dad, I want to make knives”, the young lad said; and a company
named for Bill Geissele’s sons, Abraham and Moses, was born.
The goal of Abraham & Moses Survival Equipment is to provide premium goods to soldiers, adventurers, hunters, and survivalists alike. By
combining methodic engineering, careful material selection, and state of the art manufacturing; A&M advances the design of hard-use tools for
the discerning customer.
A&M
KNIVES
GSOCKThe Lou Goodman Special Operations Combat Knife (GSOCK), by Abraham & Moses,
is a collaboration with master knife maker and veteran SOF soldier Lou Goodman.
Combining Lou’s extensive combat experience and the world class engineering team at
Abraham & Moses, the GSOCK is a tool that won’t let you down when your life depends
on it. This full tang knife is 10.625” and features a 5.655” blade made from Carpenter
Technologies PD1 steel. This alloy is able to be differentially heat-treated to create a
60 HRC cutting edge with a strong and ductile core. The G10 handle compliments a
lengthened ricasso that allows the knife to be used for a multitude of tasks beyond
cutting, from prying to small precision cuts. The lack of a choil to prevent snagging, and
the option to purchase “The Sheath of the Future,” machined out of 7075 Aluminum
and featuring active retainment, cements the GSOCK as true combat knife for a new
generation of warfighters.
10.625”
5.655”
A&M
KNIVES
AM-1The AM-1 knife, by Abraham & Moses, offers a modern interpretation of the timeless
drop point design. Crafted from D2 Steel, the AM-1 was designed for bushcraft,
survival and use as a camp knife. With an overall length of 9.5” and a blade measuring
4.6”, this full tang knife is ready for the most demanding tasks. The skeletonized body
helps the AM-1 maintain excellent balance, and the 3D machined G10 handles allow
the user excellent control with all types of grips and hand positions. The AM-1 is a work-
horse of a knife, ready to accompany you on your next backpacking or hunting trip.
9.5”
4.6”
A&M
KNIVES
AM-2The AM-2 knife, by Abraham & Moses, is the perfect knife for Law Enforcement and
EDC applications. It is perfect for situations where a large bladed knife is unwanted or
not necessary. The AM-2 is slim and light, making it comfortable for all day wear on a
chest-rig or a backpack. Made from D2 Steel, the AM-2 features an overall length of
8.5” and a blade measuring 3.6”. The precision machined G10 grip compliments the
sizeable handguard and allows the operator to use this knife to the full extent of its
abilities.
8.5”
3.6”
A&M
KNIVES
AM-3The AM-3 knife, by Abraham & Moses, was designed from the ground up to excel at
EDC, Fishing and Day Hiking scenarios. Its non-threatening overall size of 6.5” makes
the AM-3 optimal for belt-carry, or a crucial part of a Bug Out Bag. Made from D2
Steel, with a blade measuring 2.75”, the AM-3 does not compromise on durability or
quality, and its precision machined G10 handle will allow the user to perform tasks
usually reserved for much larger knives. The AM-3’s lightweight properties will excel
during a fishing trip or a day-hike, allowing the user to be prepared for cutting chores
without the bulk associated with much larger knives.
6.5”
2.75”
A&M
KNIVES
GEISSELE AUTOMATICSNORTH WALES, PA 19454
PHONE: 610.272.2060
EMAIL: [email protected]
ALG DEFENSENORTH WALES, PA 19454
PHONE: 610.635.8937
EMAIL: [email protected]
ABRAHAM & MOSES SURVIVAL EQUIPMENTNORTH WALES, PA 19454
PHONE: 267.652.7000
EMAIL: [email protected]
geissele.com | algdefense.com | abeandmoe.com
