1 2 6 5 7 4 3 11 13 14 10 13 14 9 8 8 13 14 12 NOTES: JOIN WALL MOUNT FLANGE TO PIPE W/ PLEXUS MA-300 THEN OVERLAY W. 1. 1/4" LAMINATE (M,WR,M,WR,MMM). LAMINATE SHALL EXTEND A MINIMUM OF 4" ONTO PIPE AND FLANGE. GEL COAT EXTERIOR OF FINISHED ASSEMBLY GRAY WITH SURFACING AGENT. 2. RESIN FOR HAND LAY-UPS: MCWHORTER 712-3765. 3. ATTACH NEOPRENE GASKET TO FLAP PLATE W/ 3M PR54 ADHESIVE. 4. FLAP HINGE IS WELDED FORMED T-304 S/S. 5. ALL HARDWARE IS T-304 S/S. 6. REVISIONS REV. DESCRIPTION NCR/ECO NO. REVISED BY DATE A FOR APPROVAL C. BARTCH 5/23/2013 B REVISED BOLT HOLE SIZE C. BARTCH 6/17/2013 BOM TABLE ITEM NO. QTY. PARTNAME MATERIAL 1 1 WALL MOUNT FLANGE PLATE FRP (HLU, POLYESTER) 2 1 2'-0" ID PIPE FRP (HLU, POLYESTER) 3 1 FLAP SEAL, 2'-3" X 1/4" THK NEOPRENE (55- 65 DURO) 4 1 FLAP PLATE, 2'-3" X 1" THK. FRP (HLU, POLYESTER) 5 1 HINGE ARM CHANNEL WELDMENT T-304 S/S 6 2 HINGE FLANGE MOUNT ANGLE T-304 S/S 7 2 HINGE FLANGE MOUNT ANGLE T-304 S/S 8 4 FLANGED SLEEVE BEARING, FOR 1/2" SHAFT (5/8" OD) X 1/2" LG. (SAE 841) BRONZE 9 2 HHCS, 1/2-13UNC X 10" LG., S/S T-304 S/S 10 4 ELEVATOR BOLT, C'SINK, SQ NECK 1/2-13UNC X 2 1/4" LG T-304 S/S 11 4 FHSCS, 1/2-13UNC X 2" LG T-304 S/S 12 1 HHCS, 1/2-13UNC X 1 1/2" T-304 S/S 13 12 FLAT WASHER, 1/2" T-304 S/S 14 10 HEX NUT, 1/2-13UNC T-304 S/S PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF PLASTI-FAB. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTEN PERMISSIONOF PLASTI-FAB IS PROHIBITED. D SIZE REV. B SCALE: CHECKED BY: DRAWING NO.: REP: P.O. NO: PROJECT: CUSTOMER: DATE: DRAWN BY: 131221-1A-01 BURGH SCHOENENBERGER B130514 1:2 WEIGHT: 103.82 SHEET: 1 OF 2 5/23/2013 NAME: SPECIAL FINISH REQUIREMENT: MATERIAL INFORMATION: PLASTI-FAB PART NUMBER: - TITLE: UNLESS OTHERWISE SPECIFIED. DIMENSIONS ARE IN FEET/INCHES TOLERANCES UNLESS OTHERWISE SPECIFIED. < 6'-0" > 25'-0" 1/16" 1/8" 1/2" > 6'-0" AND < 25'-0" C. BARTCH TUALATIN, OR. EVERGREEN LANDING EAST AMHERST, NY USA BURGH SCHOENENBERGER 24" FLAP GATE, FLANGE MOUNT
Transcript
1
2
6
5
7
4 3
11 13 14
10 13 14
9 8 8 13 14
12
NOTES:JOIN WALL MOUNT FLANGE TO PIPE W/ PLEXUS MA-300 THEN OVERLAY W. 1.1/4" LAMINATE (M,WR,M,WR,MMM). LAMINATE SHALL EXTEND A MINIMUM OF 4" ONTO PIPE AND FLANGE.GEL COAT EXTERIOR OF FINISHED ASSEMBLY GRAY WITH SURFACING AGENT.2.RESIN FOR HAND LAY-UPS: MCWHORTER 712-3765.3.ATTACH NEOPRENE GASKET TO FLAP PLATE W/ 3M PR54 ADHESIVE.4.FLAP HINGE IS WELDED FORMED T-304 S/S.5.ALL HARDWARE IS T-304 S/S.6.
8 4 FLANGED SLEEVE BEARING, FOR 1/2" SHAFT (5/8" OD) X 1/2" LG. (SAE 841) BRONZE
9 2 HHCS, 1/2-13UNC X 10" LG., S/S T-304 S/S
10 4 ELEVATOR BOLT, C'SINK, SQ NECK 1/2-13UNC X 2 1/4" LG T-304 S/S
11 4 FHSCS, 1/2-13UNC X 2" LG T-304 S/S
12 1 HHCS, 1/2-13UNC X 1 1/2" T-304 S/S
13 12 FLAT WASHER, 1/2" T-304 S/S
14 10 HEX NUT, 1/2-13UNC T-304 S/S
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF PLASTI-FAB. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSIONOF PLASTI-FAB IS PROHIBITED.
DSIZE REV.
BSCALE: CHECKED BY:
DRAWING NO.:
REP:
P.O. NO:
PROJECT:
CUSTOMER:
DATE:DRAWN BY: 131221-1A-01
BURGH SCHOENENBERGER
B130514
1:2WEIGHT: 103.82 SHEET: 1 OF 2
5/23/2013
NAME:
SPECIAL FINISH REQUIREMENT:
MATERIAL INFORMATION:
PLASTI-FAB PART NUMBER:
-
TITLE:
UNLESS OTHERWISE SPECIFIED.DIMENSIONS ARE IN FEET/INCHES
TOLERANCES UNLESS OTHERWISE SPECIFIED.< 6'-0"
> 25'-0"
1/16"
1/8"
1/2"
> 6'-0" AND < 25'-0" C. BARTCH
TUALATIN, OR.
EVERGREEN LANDINGEAST AMHERST, NY USA
BURGH SCHOENENBERGER
24" FLAP GATE, FLANGE MOUNT
3'-2
"
1'-1
0"
1'-4"
R1'-4"
20X 138" THRU ALL
EQ. SP. ON2'-5 1/2" B.C.
A
A
B B
1 2"
3"
91116"
11116"
14" NEOPRENE
SEAL
1" FRPPLATE
1"
2'
-0"
15°
SECTION A-A
2
1
6
5
7
3
4
12
SECTION B-B
9 13 138 8 14
7
7
5
12
NOTES:SEE SHEET 1 FOR BALLOON REFERENCES.1.JOIN WALL MOUNT FLANGE TO PIPE W/ PLEXUS MA-300 THEN OVERLAY W. 2.1/4" LAMINATE (M,WR,M,WR,MMM). LAMINATE SHALL EXTEND A MINIMUM OF 4" ONTO PIPE AND FLANGE.GEL COAT EXTERIOR OF FINISHED ASSEMBLY GRAY WITH SURFACING AGENT.3.RESIN FOR HAND LAY-UPS: MCWHORTER 712-3765.4.ATTACH NEOPRENE GASKET TO FLAP PLATE W/ 3M PR54 ADHESIVE.5.FLAP HINGE IS WELDED FORMED T-304 S/S.6.ALL HARDWARE IS T-304 S/S.7.
B
REVISIONS
REV. DESCRIPTION NCR/ECO NO. REVISED BY DATE
A FOR APPROVAL C. BARTCH 5/23/2013
B REVISED BOLT HOLT SIZE C. BARTCH 6/17/2013
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF PLASTI-FAB. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSIONOF PLASTI-FAB IS PROHIBITED.
DSIZE REV.
BSCALE: CHECKED BY:
DRAWING NO.:
REP:
P.O. NO:
PROJECT:
CUSTOMER:
DATE:DRAWN BY: 131221-1A-02
BURGH SCHOENENBERGER
B130514
1:3WEIGHT: 103.82 SHEET: 2 OF 2
5/23/2013
NAME:
SPECIAL FINISH REQUIREMENT:
MATERIAL INFORMATION:
PLASTI-FAB PART NUMBER:
-
TITLE:
UNLESS OTHERWISE SPECIFIED.DIMENSIONS ARE IN FEET/INCHES
TOLERANCES UNLESS OTHERWISE SPECIFIED.< 6'-0"
> 25'-0"
1/16"
1/8"
1/2"
> 6'-0" AND < 25'-0" C. BARTCH
TUALATIN, OR.
EVERGREEN LANDINGEAST AMHERST, NY USA
BURGH SCHOENENBERGER
24" FLAP GATE, FLANGE MOUNT
11131312
2 3
14 12 13
1
1
2
5
4
6
13121311
3
7151516
8
9
10
"D" SEAL BOM LENGTH IS APPROX.& SHOULD BE SIZED TO PIPE AS REQUIRED
NOTES:JOIN WALL MOUNT FLANGE TO PIPE W/ PLEXUS MA-300 THEN OVERLAY W. 1/4" LAMINATE (M,WR,M,WR,MMM). 1.LAMINATE SHALL EXTEND A MINIMUM OF 4" ONTO PIPE AND FLANGE.GEL COAT EXTERIOR OF FINISHED ASSEMBLY GRAY WITH SURFACING AGENT. DO NO GEL COAT SEATING SURFACES.2.RESIN FOR HAND LAY-UPS: MCWHORTER 712-3765.3.ATTACH NEOPRENE GASKET TO END OF PIPE W/ 3M PR54 ADHESIVE.4.FLAP HINGE IS WELDED FORMED T-304L S/S.5.ALL HARDWARE IS T-304 S/S.6.ANCHORS ARE T-304 S/S.7.
REVISIONS
REV. DESCRIPTION NCR/ECO NO. REVISED BY DATE
A FOR APPROVAL A. PATTERSON 7/14/2014
BOM TABLE
ITEM NO. QTY. DESCRIPTION MATERIAL LENGTH PART NUMBER
1 1 WALL PLATE AND PIPE ASSEMBLY FGWM048-2-01
2 1 DOME FLAP 4'-0" FRP (HLU, POLYESTER) 1000-0683
3 1 1/2" HOLLOW "D" GASKET NEOPRENE (50 DURO) -
4 1 FLAP ANGLE T-304L S/S FGWM048-2-02
5 2 DOUBLE ANGLE WITH UHMW FGWM048-2-03
6 2 HINGE BRACKET T-304L S/S FGWM048-2-04
7 2 3/4-10UNC THREADED ROD T-304L S/S 6 1/4" 446-0010
8 4 BUSHING, 1/2" ID X 5/8" OD BRASS 1 1/8" 660-0013
14 4 FHSCS, 1/2-13UNC X 2 1/4" LG T-304 S/S 661-0155
15 4 HEX NUT, 3/4-10UNC T-304 S/S 663-0055
16 2 WASHER, FLAT 3/4" T-304 S/S 664-0054
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF PLASTI-FAB. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSIONOF PLASTI-FAB IS PROHIBITED.
DSIZE REV.
ASCALE: CHECKED BY:
DRAWING NO.:
REP:
P.O. NO:
PROJECT:
CUSTOMER:
DATE:DRAWN BY: FGWM048-2
FLOYD JOHNSTON CONSTRUCTION
LOI
1:5WEIGHT: 325 SHEET: 1 OF 7
7/14/14
NAME:
SPECIAL FINISH REQUIREMENT:
MATERIAL INFORMATION:
PLASTI-FAB PART NUMBER:FGWM048-2
TITLE:
UNLESS OTHERWISE SPECIFIED.DIMENSIONS ARE IN FEET/INCHES
TOLERANCES UNLESS OTHERWISE SPECIFIED.< 6'-0"
> 25'-0"
1/16"
1/8"
1/2"
> 6'-0" AND < 25'-0" A. PATTERSON
TUALATIN, OR.
SALINAS INDUSTRIAL WW CONVEYANCE, USA
MISCO-NW
48" FLAP GATE, WALL MOUNT
6112"
14X 58" THRU
EQUALLY SPACED
12"
26° TYP
5714" B.C.
A
A
1"
1 2"
1" GROUT BY OTHERS
48"
15°
19516"
1" GROUTBY OTHERS
B
E
E
SECTION A-A
12" DETAIL B
SCALE 1 : 1
"D" GASKETBONDED IN PLACE
14" 14"
12"
.02 TYP UHMW
SECTION E-E SCALE 1 : 1.5
BUSHING, 1/2" ID X 5/8" OD
REVISIONS
REV. DESCRIPTION NCR/ECO NO. REVISED BY DATE
A FOR APPROVAL A. PATTERSON 7/14/2014
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF PLASTI-FAB. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSIONOF PLASTI-FAB IS PROHIBITED.
DSIZE REV.
ASCALE: CHECKED BY:
DRAWING NO.:
REP:
P.O. NO:
PROJECT:
CUSTOMER:
DATE:DRAWN BY: FGWM048-880-2
FLOYD JOHNSTON CONSTRUCTION
LOI
1:6WEIGHT: 325 SHEET: 2 OF 7
7/14/14
NAME:
SPECIAL FINISH REQUIREMENT:
MATERIAL INFORMATION:
PLASTI-FAB PART NUMBER:FGWM048-2
TITLE:
UNLESS OTHERWISE SPECIFIED.DIMENSIONS ARE IN FEET/INCHES
TOLERANCES UNLESS OTHERWISE SPECIFIED.< 6'-0"
> 25'-0"
1/16"
1/8"
1/2"
> 6'-0" AND < 25'-0" A. PATTERSON
TUALATIN, OR.
SALINAS INDUSTRIAL WW CONVEYANCE, USA
MISCO-NW
48" FLAP GATE, WALL MOUNT
151413
1223
1223
????
12
4
5
6
7
8
9
10
11
4
NOTES:JOIN WALL MOUNT FLANGE TO PIPE W/ PLEXUS MA-300 THEN OVERLAY W. 1.1/4" LAMINATE (M,WR,M,WR,MMM). LAMINATE SHALL EXTEND A MINIMUM OF 4" ONTO PIPE AND FLANGE.GEL COAT EXTERIOR OF FINISHED ASSEMBLY GRAY WITH SURFACING AGENT. 2.DO NO GEL COAT SEATING SURFACES.RESIN FOR HAND LAY-UPS: MCWHORTER 712-3765.3.ATTACH RUBBER GASKET TO END OF PIPE W/ 3M PR54 ADHESIVE.4.FLAP HINGE IS WELDED FORMED T-304 S/S.5.ALL HARDWARE IS T-304 S/S.6.ANCHORS ARE T-304 S/S.7.
5 1 2 WALL MOUNT FLANGE PLATE FRP (HLU, POLYESTER)
6 1 2 5'-0" ID PIPE FRP (HLU, POLYESTER)
7 1 2 DOME FLAP, 5'-0" FRP (HLU, POLYESTER)
8 1 2 FLAP ANGLE T-304 S/S
9 2 4 HINGE ARM T-304 S/S
10 2 4 HINGE BRACKET T-304 S/S
11 1 2 1/2" HOLLOW "D" GASKET NEOPRENE (50 DURO)
12 4 8 1/2"x1 1/8" BUSHING BRASS
13 2 4 HEX NUT 3/4-10UNC W/ WASHER T-304 S/S
14 2 4 HEX NUT 3/4-10UNC T-304 S/S
15 2 4 3/4-10UNC X 6 1/4" THREADED ROD T-304 S/S
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF PLASTI-FAB. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSIONOF PLASTI-FAB IS PROHIBITED.
DSIZE REV.
ASCALE: CHECKED BY:
DRAWING NO.:
REP:
P.O. NO:
PROJECT:
CUSTOMER:
DATE:DRAWN BY: 121498-1A-01
DAVE HEINER ASSOCIATES
9929
1:5WEIGHT: 478.44 SHEET: 1 OF 2
11/16/2012
NAME:
SPECIAL FINISH REQUIREMENT:
MATERIAL INFORMATION:
PLASTI-FAB PART NUMBER:
-
TITLE:
UNLESS OTHERWISE SPECIFIED.DIMENSIONS ARE IN FEET/INCHES
TOLERANCES UNLESS OTHERWISE SPECIFIED.< 6'-0"
> 25'-0"
1/16"
1/8"
1/2"
> 6'-0" AND < 25'-0" J.LAUGHLIN
TUALATIN, OR.
WALKER DIVINGHAMMONTON, NJ USA
DAVE HEINER & ASSOCIATES
60" FLAP GATE, WALL MOUNT
14X 58"
EQ. SP. ON5'-9 1/4" B.C.
6'-112"
1'-0
"
A
A
1"
1 2"
34"
238" MIN.
EMBEDMENT
1" GROUT BY OTHERS
5'-0
"
15°
1'-101116"
SECTION A-A
REVISIONS
REV. DESCRIPTION NCR/ECO NO. REVISED BY DATE
A FOR APPROVAL J.LAUGHLIN 11/16/2012
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF PLASTI-FAB. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSIONOF PLASTI-FAB IS PROHIBITED.
DSIZE REV.
ASCALE: CHECKED BY:
DRAWING NO.:
REP:
P.O. NO:
PROJECT:
CUSTOMER:
DATE:DRAWN BY: 121498-1A-02
DAVE HEINER ASSOCIATES
9929
1:6WEIGHT: 478.44 SHEET: 2 OF 2
11/16/2012
NAME:
SPECIAL FINISH REQUIREMENT:
MATERIAL INFORMATION:
PLASTI-FAB PART NUMBER:
-
TITLE:
UNLESS OTHERWISE SPECIFIED.DIMENSIONS ARE IN FEET/INCHES
TOLERANCES UNLESS OTHERWISE SPECIFIED.< 6'-0"
> 25'-0"
1/16"
1/8"
1/2"
> 6'-0" AND < 25'-0" J.LAUGHLIN
TUALATIN, OR.
WALKER DIVINGHAMMONTON, NJ USA
DAVE HEINER & ASSOCIATES
60" FLAP GATE, WALL MOUNT
8109
12131314
12131314
11
1
2
4
7
6
5
3
16
15 13 14
16
NOTES:JOIN WALL MOUNT FLANGE TO PIPE W/ PLEXUS MA-300 THEN OVERLAY W. 1.1/4" LAMINATE (M,WR,M,WR,MMM). LAMINATE SHALL EXTEND A MINIMUM OF 4" ONTO PIPE AND FLANGE.GEL COAT EXTERIOR OF FINISHED ASSEMBLY GRAY WITH SURFACING AGENT. 2.DO NOT GEL COAT SEATING SURFACES.RESIN FOR HAND LAY-UPS: MCWHORTER 712-3765.3.ATTACH RUBBER GASKET TO END OF PIPE W/ 3M PR54 ADHESIVE.4.FLAP HINGE IS WELDED FORMED T-304 S/S.5.ALL HARDWARE IS T-304 S/S.6.ANCHORS ARE T-304 S/S.7.
REVISIONS
REV. DESCRIPTION NCR/ECO NO. REVISED BY DATE
A FOR APPROVAL Z.MENLE 04/10/2013
BOM TABLE
ITEM NO. QTY. DESCRIPTION MATERIAL
1 1 WALL MOUNT FLANGE PLATE FRP (HLU, POLYESTER)
2 1 6'-0" ID PIPE FRP (HLU, POLYESTER)
3 1 1/2" HOLLOW "D" GASKET NEOPRENE (55-65 DURO)
4 1 DOME FLAP, 5'-0" FRP (HLU, POLYESTER)
5 2 HINGE BRACKET T-304L S/S
6 2 HINGE ARM T-304L S/S
7 1 FLAP ANGLE T-304L S/S
8 2 3/4-10UNC X 6 1/4" THREADED ROD T-304 S/S
9 2 HEX NUT 3/4-10UNC W/ WASHER T-304 S/S
10 2 HEX NUT, 3/4-10UNC T-304 S/S
11 4 BUSHING, 1/2" ID X 5/8" OD X 1 1/8" LG. BRASS
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF PLASTI-FAB. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSIONOF PLASTI-FAB IS PROHIBITED.
DSIZE REV.
ASCALE: CHECKED BY:
DRAWING NO.:
REP:
P.O. NO:
PROJECT:
CUSTOMER:
DATE:DRAWN BY: 131155-1A-01
MELLEN & ASSOCIATES
10983
1:5WEIGHT: 531.78 SHEET: 1 OF 2
04/10/2013
NAME:
SPECIAL FINISH REQUIREMENT:
MATERIAL INFORMATION:
PLASTI-FAB PART NUMBER:
-
TITLE:
UNLESS OTHERWISE SPECIFIED.DIMENSIONS ARE IN FEET/INCHES
TOLERANCES UNLESS OTHERWISE SPECIFIED.< 6'-0"
> 25'-0"
1/16"
1/8"
1/2"
> 6'-0" AND < 25'-0" Z.MENLE
TUALATIN, OR.
PAWNEE BRIDGEWICHITA, KS USA
MELLEN & ASSOCIATES
72" FLAP GATE, WALL MOUNT
7'-112"
14X 58"
EQ. SP. ON6'-8 1/4" B.C.
7'-8
3 4"
1'-2
"
A
A
1"
1 2"
34"
1"
2"
2"
1"
238" MIN.
EMBEDMENT
1" GROUT BY OTHERS
6'-0
"
14°
2'-38"
SECTION A-A
REVISIONS
REV. DESCRIPTION NCR/ECO NO. REVISED BY DATE
A FOR APPROVAL Z.MENLE 04/10/2013
PROPRIETARY AND CONFIDENTIALTHE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF PLASTI-FAB. ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE
WRITTEN PERMISSIONOF PLASTI-FAB IS PROHIBITED.
DSIZE REV.
ASCALE: CHECKED BY:
DRAWING NO.:
REP:
P.O. NO:
PROJECT:
CUSTOMER:
DATE:DRAWN BY: 131155-1A-02
MELLEN & ASSOCIATES
10983
1:7WEIGHT: 531.78 SHEET: 2 OF 2
04/10/2013
NAME:
SPECIAL FINISH REQUIREMENT:
MATERIAL INFORMATION:
PLASTI-FAB PART NUMBER:
-
TITLE:
UNLESS OTHERWISE SPECIFIED.DIMENSIONS ARE IN FEET/INCHES
