Engine Isuzu AI-4HK1X Tier 3 turbocharged diesel engine with electronic fuel control, 4-cylinder, water-cooled, EGR with cooler, Air-to-air intercooler, Fuel cooler, Auto idle start, Neutral safety start, Glow plugs, Auto warm-up, EPF engine protection, Dual stage fuel filtration, Remote oil filter, Green plug oil drain.

SAE net horsepower .............. 177 HP (132 kW) @ 2,000 rpmDisplacement ................................................................... 5.2 LMaximum torque.................. 469 lbf-ft (636 N-m) @ 1,500 rpmStarter ..................................................................... 24V-5.0kWAlternator ...................................................................... 50 ampBattery .......................................................... 92 x 2 amp hours

Cab and Controls Oregon OSHA certified side-entry forestry cab, KAB® 855 air-suspension seat with belt, Control panel with illuminated soft-touch switches, LCD monitor, Low-effort controls pre-wired for auxiliary hydraulics, Sliding 4-position tilting control consoles, Climate control, Sky roof, (2) Intermittent windshield wipers with washer, Single pedal travel, Travel alarm, Footrests, Cup holder, 12-volt outlet, Digital clock, 24-volt cigarette lighter, Ashtray, Dome lights, Coat hook, Adjustable horn, Mirror, Handrails with deflector, Floor mat, Emergency exit.

Selectable working modes, Anti-theft password protection system, On-board self-diagnostic system with memory, Auto-idling system, One-touch decelerator, Gate lock safety shutoff.

A/C output..........................................................18,100 BTU/hrHeater output .....................................................20,150 BTU/hr

Hydraulic System Open-center system, (2) variable displacement axial piston pumps, (1) gear pump for pilot controls, (1) gear pump/valve for processor rotate, Main control valve with one 4-spool valve and one 5-spool valve with auxiliary spool, Combination double-pump flow to processor, Auxiliary pump for rotate, Processor return line fitting, Oil cooler, O-ring face seals, High-performance 6-micron return filter, Firewall.Hydraulic PumpsMaximum flow .............................. 2 x 61.8 gpm (2 x 234 l/min)Pilot pump maximum flow ........................... 5.3 gpm (20 l/min)Auxiliary pump maximum flow .................. 9.7 gpm (36.8 l/min)Relief Valve SettingsBoom up/arm/tool ....................................... 4,970 psi (343 bar)Swing circuit ............................................... 4,260 psi (294 bar)Travel .......................................................... 4,970 psi (343 bar)

Hydraulic Oil FiltrationReturn filter ................................................................. 6 micronPilot filter ..................................................................... 8 micronSuction screen....................................................... 105 micron

Swing Planetary reduction powered by axial piston motor. Internal ring gear with grease cavity for swing pinion. Swing bearing is single-row shear type ball bearing. Mechanical disc swing brake. Auto power swing.

Swing speed ........................................................... 0 - 8.7 rpmTail swing ........................................................... 9´ 8˝ (2.94 m)Swing torque ................................... 68,200 lbf-ft. (92.5 kN•m)

Undercarriage High-Wide or High-Narrow track gauge options with x-pattern carbody, Full-length track guards, Sealed and strutted track chain, Sealed rollers and idlers, Idler mount reinforcement, Two-speed independent hydrostatic travel with compact planetary final drive, HD travel motor covers, Disc type brakes, Adjustable track tension, HD swivel guard – hinged.Carrier rollers ............................................................ 2 per sideTrack rollers .............................................................. 8 per sideTrack link pitch ................................................. 8.50˝ (216 mm)Shoes ..................................................................... 47 per sideShoe width ....................................................... 27.5˝ (700 mm)Ground Pressure (High-Wide) Side-entry cab, 9˝ riser ........................... 8.15 psi (.562 bar)

Lubricant and Coolant Capacity Fuel tank ................................................. 108.3 gal. (410 liters)Hydraulic tank ........................................... 38.8 gal. (147 liters)Hydraulic system ...................................... 66.0 gal. (250 liters)Final drive (per side) .................................... 2.5 gal. (9.5 liters)Swing drive .................................................. 1.6 gal. (6.0 liters)Engine oil ................................................. 6.10 gal. (23.1 liters)Cooling system ........................................ 6.65 gal. (25.2 liters)

Travel System Two-speed independent hydrostatic travel with compact axial piston motors. Hydraulic motor powered output shaft coupled to a planetary reduction unit and track sprocket. All hydraulic components mounted within the width of side frame. Automatic downshift. Single pedal travel. Spring applied, hydraulically released disc parking brake built into each motor. Each travel motor equipped with counterbalance valve to prevent overspeeding down an incline.

Max. travel speed .......................... 1.6 - 2.7 mph (2.6 - 4.3 km/h)Drawbar pull ................................................. 60,300 lbf (268 kN)Gradeability ................................................................ 70% (35°)Attachment Equipped with High-Lift boom relocation bracketBoom ............................................................... 19´ 2˝ (5.85 m)Arm .................................................................... 9´ 10˝ (3.0 m)

Operating Weights Working weight with OROSHA side-entry forestry cab, 9˝ (229 mm) cab riser, high-wide undercarriage, 27.5˝ (700 mm) 2-bar shoes ............... 62,390 lbs (28 300 kg)

(no processing tool)

For 15˝ (384 mm) cab riser ...................... Add 148 lbs (67 kg)For high-narrow undercarriage ........ Subtract 147 lbs (67 Kg)

240 X2 DHP SpecificationsStandard Equipment

● Oregon-OSHA certified side-entry forestry cab with sky roof and escape hatch

● (8) HID high-intensity exterior lights with remote machine light-up; (5) cab, (1) RH corner guard, (2) boom

● Key fob with remote light● KAB 855 air-suspension seat, sliding/reclining,

adjustable armrests, lumbar support, retractable seat belt and foot rests

● 4-position tilting consoles with memory position and hydraulic lock-out

● Auto climate control a/c and heat, defrost● Sirius® Satellite and iPod® ready sound system

with AM/FM, MP3 interface, dual speakers and mute button

● Job ticket slot, cup holder, 12-volt accessory outlet, digital clock, 24-volt cigarette lighter, ashtray, dome lights, coat hook, adjustable horn, mirror, floor mat

● Illuminated LCD monitor and control panel with soft-touch switches

● Anti-theft device● (2) Intermittent windshield wipers with washer● Single pedal travel● Travel alarm with cancellation switch● CB radio antenna mounting provision● EPA Tier III Isuzu diesel engine● Common rail fuel injection● Turbocharger with intercooler● Neutral safety start● Idle start● Glow plug pre-heat● Auto engine warm-up● Auto idling system● One-touch idle● Dual remote fuel filters with water separation● Double element air filter with in-cab restriction indicator● External fuel gauge● Forestry-style debris screened house doors

● Remote, full-flow engine oil filter● Green plug engine oil drain● EPF Engine Protection● Emergency engine stop● Open-center hydraulic system● Selectable work modes● Auto swing priority● Combination double-pump flow to processor● Auxiliary pump for rotate● Processor return line connection● Sealed and lubricated track chain● Forestry-style upper roller brackets● Two-speed with auto shift and straight travel● Planetary drive● Spring-applied, hydraulic release brake● Hydraulic track adjust● Full-length track guides● HD swivel guard belly pan● HD upper belly pans● HD reinforced frame● HD pump and radiator doors with adjustable

shimming system● HD tank skin● HD catwalks - welded● HD turntable bearing and swing motor● HD travel motor covers● RH corner guard with light● Upper deck handrails● Vandal locks with common key● Non-skid surface pads● Attachment cushion valve● Arm and boom regeneration● Boom holding valve● Cylinder cushion - integral● Centralized lube banks● On-board diagnostic system● 12,790 lb (5 800 kg) forestry counterweight

● Cab risers for side-entry OROSHA certified forestry cab

15-in (381 mm) 9-in (229 mm)● High-Wide undercarriage 11´-11´´ (3.64 m)● High-Narrow undercarriage 11´-5´´ (3.50 m)● Tracks 27.5-in (700 mm) 2-bar grouser

Options

LBX Company is the proud maker of quality Link-Belt excavators and is located in Lexington, KY. www.lbxco.comLitho in USA 2/12 #LBX2200® LBX and ® Link-Belt are registered trademarks. Copyright 2012. All rights reserved. We are constantly improving our products and therefore reserve the right to change designs and specifications.

For Use in Harvester Processing Applications

240 X2 DHP Specifications 240 X2 DHP Specifications

Travel Dimensions (with 9˝ cab riser)

15´ 11˝ (4.87 m)

12´ 10˝ (3.91 m)

11´ 1˝ (3.37 m)

5´ 5˝(1.66 m)

5´ 8˝(1.72 m)9´ 8˝ (2.94 m)

2´ 4˝(705 mm)

32´ 2˝ (9.80 m)

1.5˝

(38.

1 m

m)

4´ 7

˝(1

.40

m)

2´ 4˝(700 mm)

22´ 6˝ (6.86 m)

10´

3˝ (

3.13

m)

12´

2˝ (

3.70

m)

10´

11˝

(3.3

3 m

)

High Wide Transport DimensionsHigh Narrow Transport Dimensions

9´ 8˝(2.94 m)

9´ 2˝(2.79 m)

11´ 11˝(3.64 m)

11´ 5˝(3.50 m)

1. Lifting capacities shown should not be exceeded. Weight of all lifting accessories must be deducted from the above lifting capacities.

2. Lifting capacities are based on machine standing on firm, uniform supporting surface. User must make allowances for job conditions such as soft or uneven ground.

3. Lifting capacities shown do not exceed 75% of minimum tipping loads or 87% of hydraulic capacities. Capacities marked with an asterisk (*) are limited by hydraulic capacities.

4. Least stable position is over the side.

5. Operator should be fully acquainted with the Operator’s Manual & Operating Safety Booklet, furnished by LBX before operating the machine.

6. Capacities apply only to the machine as originally manufactured and normally equipped by LBX Company LLC.

Notes: Lifting capacities

9´ 10˝ (3.0 m) Arm with 19´ 2˝ (5.85 m) Boom in High Lift Position and High Narrow Lower

9´ 10˝ (3.0 m) Arm with 19´ 2˝ (5.85 m) Boom in High Lift Position and High Wide Lower

Radius of Load5´ 0˝ (1.52 m) 10´ 0˝ (3.05 m) 15´ 0˝ (4.57 m) 20´ 0˝ (6.10 m) 25´ 0˝ (7.62 m) 30´ 0˝ (9.14 m) Cap at Max Reach

End Side End Side End Side End Side End Side End Side End Side +30´0˝ lbs 9.14 m (kg)

10,600* 10,600* 7,100* 7,100*4 808* 4 808* 3 221* 3 221*

+25´0˝ lbs 7.62 m (kg)

12,000* 12,000* 10,300* 10,300* 6,550* 6,550*5 443* 5 443* 4 672* 4 672* 2 971* 2 971*

+20´0˝ lbs 6.10 m (kg)

15,600* 15,600* 14,750* 14,750* 12,050* 12,050* 6,950* 6,950* 6,350* 6,350*7 076* 7 076* 6 690* 6 690* 5 466* 5 466* 3 152* 3 152* 2 880* 2 880*

+15´0˝ lbs 4.57 m (kg)

25,450* 25,450* 21,050* 21,050* 17,450* 17,450* 14,100* 14,100* 10,600* 10,600* 6,350* 6,350*11 544* 11 544* 9 548* 9 548* 7 915* 7 915* 6 396* 6 396* 4 808* 4 808* 2 880* 2 880*

+10´0˝ lbs 3.05 m (kg)

36,500* 36,500* 25,400* 25,400* 19,500* 19,500* 16,200* 15,500 12,500* 12,000 6,500* 6,500*16 556* 16 556* 11 521* 11 521* 8 845* 8 845* 7 348* 7 031 5 670* 5 443 2 948* 2 948*

+5´0˝ lbs 1.52 m (kg)

20,900* 20,900* 28,250* 28,250* 20,950* 20,400 16,850* 15,050 13,550* 11,750 6,800* 6,800*9 480* 9 480* 12 814* 12 814* 9 503* 9 253 7 643* 6 827 6 146* 5 330 3 084* 3 084*

Ground lbs Line (kg)

11,400* 11,400* 22,150* 22,150* 28,650* 28,650* 21,300* 19,800 16,900* 14,750 12,350* 11,600 7,350* 7,350*5 171* 5 171* 10 047* 10 047* 12 995* 12 995* 9 662* 8 981 7 666* 6 690 5 602* 5 262 3 334* 3 334*

-5´0˝ lbs -1.52 m (kg)

18,550* 18,550* 28,200* 28,200* 27,700* 27,700* 20,800* 19,500 16,250* 14,550 8,300* 8,300*8 414* 8 414* 12 791* 12 791* 12 565* 12 565* 9 435* 8 845 7 371* 6 600 3 765* 3 765*

-10´0˝ lbs 3.05 m (kg)

33,350* 33,350* 24,500* 24,500* 18,600* 18,600* 13,700* 13,700* 10,250* 10,250*15 127* 15 127* 11 113* 11 113* 8 437* 8 437* 6 214* 6 214* 4 649* 4 649*

Radius of Load5´ 0˝ (1.52 m) 10´ 0˝ (3.05 m) 15´ 0˝ (4.57 m) 20´ 0˝ (6.10 m) 25´ 0˝ (7.62 m) 30´ 0˝ (9.14 m) Cap at Max Reach

End Side End Side End Side End Side End Side End Side End Side +30´0˝ lbs 9.14 m (kg)

10,600* 10,600* 7,100* 7,100*4 808* 4 808* 3 221* 3 221*

+25´0˝ lbs 7.62 m (kg)

12,000* 12,000* 10,300* 10,300* 6,550* 6,550*5 443* 5 443* 4 672* 4 672* 2 971* 2 971*

+20´0˝ lbs 6.10 m (kg)

15,600* 15,600* 14,750* 14,750* 12,050* 12,050* 6,950* 6,950* 6,350* 6,350*7 076* 7 076* 6 690* 6 690* 5 466* 5 466* 3 152* 3 152* 2 880* 2 880*

+15´0˝ lbs 4.57 m (kg)

25,450* 25,450* 21,050* 21,050* 17,450* 17,450* 14,100* 14,100* 10,600* 10,600* 6,350* 6,350*11 544* 11 544* 9 548* 9 548* 7 915* 7 915* 6 396* 6 396* 4 808* 4 808* 2 880* 2 880*

+10´0˝ lbs 3.05 m (kg)

36,500* 36,500* 25,400* 25,400* 19,500* 19,500* 16,200* 16,200* 12,500* 12,500* 6,500* 6,500*16 556* 16 556* 11 521* 11 521* 8 845* 8 845* 7 348* 7 348* 5 670* 5 670* 2 948* 2 948*

+5´0˝ lbs 1.52 m (kg)

20,900* 20,900* 28,250* 28,250* 20,950* 20,950* 16,850* 15,950 13,550* 12,450 6,800* 6,800*9 480* 9 480* 12 814* 12 814* 9 503* 9 503* 7 643* 7 235 6 146* 5 647 3 084* 3 084*

Ground lbs Line (kg)

11,400* 11,400* 22,150* 22,150* 28,650* 28,650* 21,300* 21,050 16,900* 15,600 12,350* 12,250 7,350* 7,350*5 171* 5 171* 10 047* 10 047* 12 995* 12 995* 9 662* 9 548 7 666* 7 076 5 602* 5 557 3 334* 3 334*

-5´0˝ lbs -1.52 m (kg)

18,550* 18,550* 28,200* 28,200* 27,700* 27,700* 20,800* 20,700 16,250* 15,400 8,300* 8,300*8 414* 8 414* 12 791* 12 791* 12 565* 12 565* 9 435* 9 389 7 371* 6 985 3 765* 3 765*

-10´0˝ lbs 3.05 m (kg)

33,350* 33,350* 24,500* 24,500* 18,600* 18,600* 13,700* 13,700* 10,250* 10,250*15 127* 15 127* 11 113* 11 113* 8 437* 8 437* 6 214* 6 214* 4 649* 4 649*

Lifting CapacitiesWorking Ranges

50

-5

-10

-15 ft.

5

10

15

20

25

30

35

40 ft.

1015202530

A

C

D

E

B

22022

Machine equipped with processor attachment

A. Maximum reach 28´ 7˝ (8.7 m)

B. Maximum reach 27´ 8˝ @ ground level (8.4 m)

C. Maximum depth 11´ 11˝ (3.6 m)

D. Maximum height 33´ 1˝ (10.1 m)

E. Maximum height @ 23´ 8˝ log level - 30˝ (.76 m) log (7.2 m)

240 X2 DHP Specifications 240 X2 DHP Specifications

Travel Dimensions (with 9˝ cab riser)

15´ 11˝ (4.87 m)

12´ 10˝ (3.91 m)

11´ 1˝ (3.37 m)

5´ 5˝(1.66 m)

5´ 8˝(1.72 m)9´ 8˝ (2.94 m)

2´ 4˝(705 mm)

32´ 2˝ (9.80 m)

1.5˝

(38.

1 m

m)

4´ 7

˝(1

.40

m)

2´ 4˝(700 mm)

22´ 6˝ (6.86 m)

10´

3˝ (

3.13

m)

12´

2˝ (

3.70

m)

10´

11˝

(3.3

3 m

)

High Wide Transport DimensionsHigh Narrow Transport Dimensions

9´ 8˝(2.94 m)

9´ 2˝(2.79 m)

11´ 11˝(3.64 m)

11´ 5˝(3.50 m)

1. Lifting capacities shown should not be exceeded. Weight of all lifting accessories must be deducted from the above lifting capacities.

2. Lifting capacities are based on machine standing on firm, uniform supporting surface. User must make allowances for job conditions such as soft or uneven ground.

3. Lifting capacities shown do not exceed 75% of minimum tipping loads or 87% of hydraulic capacities. Capacities marked with an asterisk (*) are limited by hydraulic capacities.

4. Least stable position is over the side.

5. Operator should be fully acquainted with the Operator’s Manual & Operating Safety Booklet, furnished by LBX before operating the machine.

6. Capacities apply only to the machine as originally manufactured and normally equipped by LBX Company LLC.

Notes: Lifting capacities

9´ 10˝ (3.0 m) Arm with 19´ 2˝ (5.85 m) Boom in High Lift Position and High Narrow Lower

9´ 10˝ (3.0 m) Arm with 19´ 2˝ (5.85 m) Boom in High Lift Position and High Wide Lower

Radius of Load5´ 0˝ (1.52 m) 10´ 0˝ (3.05 m) 15´ 0˝ (4.57 m) 20´ 0˝ (6.10 m) 25´ 0˝ (7.62 m) 30´ 0˝ (9.14 m) Cap at Max Reach

End Side End Side End Side End Side End Side End Side End Side +30´0˝ lbs 9.14 m (kg)

10,600* 10,600* 7,100* 7,100*4 808* 4 808* 3 221* 3 221*

+25´0˝ lbs 7.62 m (kg)

12,000* 12,000* 10,300* 10,300* 6,550* 6,550*5 443* 5 443* 4 672* 4 672* 2 971* 2 971*

+20´0˝ lbs 6.10 m (kg)

15,600* 15,600* 14,750* 14,750* 12,050* 12,050* 6,950* 6,950* 6,350* 6,350*7 076* 7 076* 6 690* 6 690* 5 466* 5 466* 3 152* 3 152* 2 880* 2 880*

+15´0˝ lbs 4.57 m (kg)

25,450* 25,450* 21,050* 21,050* 17,450* 17,450* 14,100* 14,100* 10,600* 10,600* 6,350* 6,350*11 544* 11 544* 9 548* 9 548* 7 915* 7 915* 6 396* 6 396* 4 808* 4 808* 2 880* 2 880*

+10´0˝ lbs 3.05 m (kg)

36,500* 36,500* 25,400* 25,400* 19,500* 19,500* 16,200* 15,500 12,500* 12,000 6,500* 6,500*16 556* 16 556* 11 521* 11 521* 8 845* 8 845* 7 348* 7 031 5 670* 5 443 2 948* 2 948*

+5´0˝ lbs 1.52 m (kg)

20,900* 20,900* 28,250* 28,250* 20,950* 20,400 16,850* 15,050 13,550* 11,750 6,800* 6,800*9 480* 9 480* 12 814* 12 814* 9 503* 9 253 7 643* 6 827 6 146* 5 330 3 084* 3 084*

Ground lbs Line (kg)

11,400* 11,400* 22,150* 22,150* 28,650* 28,650* 21,300* 19,800 16,900* 14,750 12,350* 11,600 7,350* 7,350*5 171* 5 171* 10 047* 10 047* 12 995* 12 995* 9 662* 8 981 7 666* 6 690 5 602* 5 262 3 334* 3 334*

-5´0˝ lbs -1.52 m (kg)

18,550* 18,550* 28,200* 28,200* 27,700* 27,700* 20,800* 19,500 16,250* 14,550 8,300* 8,300*8 414* 8 414* 12 791* 12 791* 12 565* 12 565* 9 435* 8 845 7 371* 6 600 3 765* 3 765*

-10´0˝ lbs 3.05 m (kg)

33,350* 33,350* 24,500* 24,500* 18,600* 18,600* 13,700* 13,700* 10,250* 10,250*15 127* 15 127* 11 113* 11 113* 8 437* 8 437* 6 214* 6 214* 4 649* 4 649*

Radius of Load5´ 0˝ (1.52 m) 10´ 0˝ (3.05 m) 15´ 0˝ (4.57 m) 20´ 0˝ (6.10 m) 25´ 0˝ (7.62 m) 30´ 0˝ (9.14 m) Cap at Max Reach

End Side End Side End Side End Side End Side End Side End Side +30´0˝ lbs 9.14 m (kg)

10,600* 10,600* 7,100* 7,100*4 808* 4 808* 3 221* 3 221*

+25´0˝ lbs 7.62 m (kg)

12,000* 12,000* 10,300* 10,300* 6,550* 6,550*5 443* 5 443* 4 672* 4 672* 2 971* 2 971*

+20´0˝ lbs 6.10 m (kg)

15,600* 15,600* 14,750* 14,750* 12,050* 12,050* 6,950* 6,950* 6,350* 6,350*7 076* 7 076* 6 690* 6 690* 5 466* 5 466* 3 152* 3 152* 2 880* 2 880*

+15´0˝ lbs 4.57 m (kg)

25,450* 25,450* 21,050* 21,050* 17,450* 17,450* 14,100* 14,100* 10,600* 10,600* 6,350* 6,350*11 544* 11 544* 9 548* 9 548* 7 915* 7 915* 6 396* 6 396* 4 808* 4 808* 2 880* 2 880*

+10´0˝ lbs 3.05 m (kg)

36,500* 36,500* 25,400* 25,400* 19,500* 19,500* 16,200* 16,200* 12,500* 12,500* 6,500* 6,500*16 556* 16 556* 11 521* 11 521* 8 845* 8 845* 7 348* 7 348* 5 670* 5 670* 2 948* 2 948*

+5´0˝ lbs 1.52 m (kg)

20,900* 20,900* 28,250* 28,250* 20,950* 20,950* 16,850* 15,950 13,550* 12,450 6,800* 6,800*9 480* 9 480* 12 814* 12 814* 9 503* 9 503* 7 643* 7 235 6 146* 5 647 3 084* 3 084*

Ground lbs Line (kg)

11,400* 11,400* 22,150* 22,150* 28,650* 28,650* 21,300* 21,050 16,900* 15,600 12,350* 12,250 7,350* 7,350*5 171* 5 171* 10 047* 10 047* 12 995* 12 995* 9 662* 9 548 7 666* 7 076 5 602* 5 557 3 334* 3 334*

-5´0˝ lbs -1.52 m (kg)

18,550* 18,550* 28,200* 28,200* 27,700* 27,700* 20,800* 20,700 16,250* 15,400 8,300* 8,300*8 414* 8 414* 12 791* 12 791* 12 565* 12 565* 9 435* 9 389 7 371* 6 985 3 765* 3 765*

-10´0˝ lbs 3.05 m (kg)

33,350* 33,350* 24,500* 24,500* 18,600* 18,600* 13,700* 13,700* 10,250* 10,250*15 127* 15 127* 11 113* 11 113* 8 437* 8 437* 6 214* 6 214* 4 649* 4 649*

Lifting CapacitiesWorking Ranges

50

-5

-10

-15 ft.

5

10

15

20

25

30

35

40 ft.

1015202530

A

C

D

E

B

22022

Machine equipped with processor attachment

A. Maximum reach 28´ 7˝ (8.7 m)

B. Maximum reach 27´ 8˝ @ ground level (8.4 m)

C. Maximum depth 11´ 11˝ (3.6 m)

D. Maximum height 33´ 1˝ (10.1 m)

E. Maximum height @ 23´ 8˝ log level - 30˝ (.76 m) log (7.2 m)

Engine Isuzu AI-4HK1X Tier 3 turbocharged diesel engine with electronic fuel control, 4-cylinder, water-cooled, EGR with cooler, Air-to-air intercooler, Fuel cooler, Auto idle start, Neutral safety start, Glow plugs, Auto warm-up, EPF engine protection, Dual stage fuel filtration, Remote oil filter, Green plug oil drain.

SAE net horsepower .............. 177 HP (132 kW) @ 2,000 rpmDisplacement ................................................................... 5.2 LMaximum torque.................. 469 lbf-ft (636 N-m) @ 1,500 rpmStarter ..................................................................... 24V-5.0kWAlternator ...................................................................... 50 ampBattery .......................................................... 92 x 2 amp hours

Cab and Controls Oregon OSHA certified side-entry forestry cab, KAB® 855 air-suspension seat with belt, Control panel with illuminated soft-touch switches, LCD monitor, Low-effort controls pre-wired for auxiliary hydraulics, Sliding 4-position tilting control consoles, Climate control, Sky roof, (2) Intermittent windshield wipers with washer, Single pedal travel, Travel alarm, Footrests, Cup holder, 12-volt outlet, Digital clock, 24-volt cigarette lighter, Ashtray, Dome lights, Coat hook, Adjustable horn, Mirror, Handrails with deflector, Floor mat, Emergency exit.

Selectable working modes, Anti-theft password protection system, On-board self-diagnostic system with memory, Auto-idling system, One-touch decelerator, Gate lock safety shutoff.

A/C output..........................................................18,100 BTU/hrHeater output .....................................................20,150 BTU/hr

Hydraulic System Open-center system, (2) variable displacement axial piston pumps, (1) gear pump for pilot controls, (1) gear pump/valve for processor rotate, Main control valve with one 4-spool valve and one 5-spool valve with auxiliary spool, Combination double-pump flow to processor, Auxiliary pump for rotate, Processor return line fitting, Oil cooler, O-ring face seals, High-performance 6-micron return filter, Firewall.Hydraulic PumpsMaximum flow .............................. 2 x 61.8 gpm (2 x 234 l/min)Pilot pump maximum flow ........................... 5.3 gpm (20 l/min)Auxiliary pump maximum flow .................. 9.7 gpm (36.8 l/min)Relief Valve SettingsBoom up/arm/tool ....................................... 4,970 psi (343 bar)Swing circuit ............................................... 4,260 psi (294 bar)Travel .......................................................... 4,970 psi (343 bar)

Hydraulic Oil FiltrationReturn filter ................................................................. 6 micronPilot filter ..................................................................... 8 micronSuction screen....................................................... 105 micron

Swing Planetary reduction powered by axial piston motor. Internal ring gear with grease cavity for swing pinion. Swing bearing is single-row shear type ball bearing. Mechanical disc swing brake. Auto power swing.

Swing speed ........................................................... 0 - 8.7 rpmTail swing ........................................................... 9´ 8˝ (2.94 m)Swing torque ................................... 68,200 lbf-ft. (92.5 kN•m)

Undercarriage High-Wide or High-Narrow track gauge options with x-pattern carbody, Full-length track guards, Sealed and strutted track chain, Sealed rollers and idlers, Idler mount reinforcement, Two-speed independent hydrostatic travel with compact planetary final drive, HD travel motor covers, Disc type brakes, Adjustable track tension, HD swivel guard – hinged.Carrier rollers ............................................................ 2 per sideTrack rollers .............................................................. 8 per sideTrack link pitch ................................................. 8.50˝ (216 mm)Shoes ..................................................................... 47 per sideShoe width ....................................................... 27.5˝ (700 mm)Ground Pressure (High-Wide) Side-entry cab, 9˝ riser ........................... 8.15 psi (.562 bar)

Lubricant and Coolant Capacity Fuel tank ................................................. 108.3 gal. (410 liters)Hydraulic tank ........................................... 38.8 gal. (147 liters)Hydraulic system ...................................... 66.0 gal. (250 liters)Final drive (per side) .................................... 2.5 gal. (9.5 liters)Swing drive .................................................. 1.6 gal. (6.0 liters)Engine oil ................................................. 6.10 gal. (23.1 liters)Cooling system ........................................ 6.65 gal. (25.2 liters)

Travel System Two-speed independent hydrostatic travel with compact axial piston motors. Hydraulic motor powered output shaft coupled to a planetary reduction unit and track sprocket. All hydraulic components mounted within the width of side frame. Automatic downshift. Single pedal travel. Spring applied, hydraulically released disc parking brake built into each motor. Each travel motor equipped with counterbalance valve to prevent overspeeding down an incline.

Max. travel speed .......................... 1.6 - 2.7 mph (2.6 - 4.3 km/h)Drawbar pull ................................................. 60,300 lbf (268 kN)Gradeability ................................................................ 70% (35°)Attachment Equipped with High-Lift boom relocation bracketBoom ............................................................... 19´ 2˝ (5.85 m)Arm .................................................................... 9´ 10˝ (3.0 m)

Operating Weights Working weight with OROSHA side-entry forestry cab, 9˝ (229 mm) cab riser, high-wide undercarriage, 27.5˝ (700 mm) 2-bar shoes ............... 62,390 lbs (28 300 kg)

(no processing tool)

For 15˝ (384 mm) cab riser ...................... Add 148 lbs (67 kg)For high-narrow undercarriage ........ Subtract 147 lbs (67 Kg)

240 X2 DHP SpecificationsStandard Equipment

● Oregon-OSHA certified side-entry forestry cab with sky roof and escape hatch

● (8) HID high-intensity exterior lights with remote machine light-up; (5) cab, (1) RH corner guard, (2) boom

● Key fob with remote light● KAB 855 air-suspension seat, sliding/reclining,

adjustable armrests, lumbar support, retractable seat belt and foot rests

● 4-position tilting consoles with memory position and hydraulic lock-out

● Auto climate control a/c and heat, defrost● Sirius® Satellite and iPod® ready sound system

with AM/FM, MP3 interface, dual speakers and mute button

● Job ticket slot, cup holder, 12-volt accessory outlet, digital clock, 24-volt cigarette lighter, ashtray, dome lights, coat hook, adjustable horn, mirror, floor mat

● Illuminated LCD monitor and control panel with soft-touch switches

● Anti-theft device● (2) Intermittent windshield wipers with washer● Single pedal travel● Travel alarm with cancellation switch● CB radio antenna mounting provision● EPA Tier III Isuzu diesel engine● Common rail fuel injection● Turbocharger with intercooler● Neutral safety start● Idle start● Glow plug pre-heat● Auto engine warm-up● Auto idling system● One-touch idle● Dual remote fuel filters with water separation● Double element air filter with in-cab restriction indicator● External fuel gauge● Forestry-style debris screened house doors

● Remote, full-flow engine oil filter● Green plug engine oil drain● EPF Engine Protection● Emergency engine stop● Open-center hydraulic system● Selectable work modes● Auto swing priority● Combination double-pump flow to processor● Auxiliary pump for rotate● Processor return line connection● Sealed and lubricated track chain● Forestry-style upper roller brackets● Two-speed with auto shift and straight travel● Planetary drive● Spring-applied, hydraulic release brake● Hydraulic track adjust● Full-length track guides● HD swivel guard belly pan● HD upper belly pans● HD reinforced frame● HD pump and radiator doors with adjustable

shimming system● HD tank skin● HD catwalks - welded● HD turntable bearing and swing motor● HD travel motor covers● RH corner guard with light● Upper deck handrails● Vandal locks with common key● Non-skid surface pads● Attachment cushion valve● Arm and boom regeneration● Boom holding valve● Cylinder cushion - integral● Centralized lube banks● On-board diagnostic system● 12,790 lb (5 800 kg) forestry counterweight

● Cab risers for side-entry OROSHA certified forestry cab

15-in (381 mm) 9-in (229 mm)● High-Wide undercarriage 11´-11´´ (3.64 m)● High-Narrow undercarriage 11´-5´´ (3.50 m)● Tracks 27.5-in (700 mm) 2-bar grouser

Options

LBX Company is the proud maker of quality Link-Belt excavators and is located in Lexington, KY. www.lbxco.comLitho in USA 2/12 #LBX2200® LBX and ® Link-Belt are registered trademarks. Copyright 2012. All rights reserved. We are constantly improving our products and therefore reserve the right to change designs and specifications.

For Use in Harvester Processing Applications