24” Marvel Beer Dispensers (Built-in and Mobile) Model # ML24B***** • Dynamic Cooling Technology ™ delivers rapid cooldown and the industry’s best temperature stability • MARVEL Intuit™ Integrated Controls ensure precise temperature management from 34°F to 46°F • Integrated drain system keeps spillage under control and removable components make for easier cleaning • Low Boy coupler makes it easier to store, tap and swap out tall barrels • Secure CO 2 tank storage area and drain basin • Close Door Assist System ™ gently and automatically closes door • Panel overlay option features soft-close integrated hinge for a truly flush fit with cabinetry • Audible and visual alarms signal when door is left ajar to protect food integrity and energy use • Drain pan and hose, 5 lb. CO 2 tank, connectors, regulator and interior floor shield included • Height adjustment up to 1” with leveling legs • Built-in and mobile models available with single or twin tap • All models feature a double insulated stainless steel tower • 1-year warranty Storage Capacity Stores half kegs, tall quarter kegs, pony kegs, sixth barrels, Cornelius kegs, growlers, bottles or cans Product Dimensions 23⅞” W x 33¾” minimum H x 25 ⅝” D (including handle) Finish/Door Options Stainless Steel Wood Overlay (Panel Ready) Ordering Details SINGLE TAP, MOBILE Solid Black Door, Stainless Handle Single Tap, Right Hinge ML24BSSMRB TWIN TAP, MOBILE Solid Black Door, Stainless Handle, Twin Tap, Right Hinge ML24BTSMRB SINGLE TAP, BUILT-IN Solid Black Door, Right Hinge ML24BSS2RB Solid Black Door, Left Hinge ML24BSS2LB Solid Stainless Steel Door, Right Hinge ML24BSS2RS Solid Stainless Steel Door, Left Hinge ML24BSS2LS Solid Panel Overlay Ready Door, Integrated Right Hinge ML24BSP3RP Solid Panel Overlay Ready Door, Integrated Left Hinge ML24BSP3LP TWIN TAP, BUILT-IN Solid Stainless Steel Door, Right Hinge ML24BTS2RS Solid Stainless Steel Door, Left Hinge ML24BTS2LS Solid Panel Overlay Ready Door, Integrated Right Hinge ML24BTP3RP Solid Panel Overlay Ready Door, Integrated Left Hinge ML24BTP3LP No panel installation kit required. Black
Transcript
24” Marvel Beer Dispensers (Built-in and Mobile)Model # ML24B*****
• Dynamic Cooling Technology™ delivers rapid cooldown and the industry’s best temperature stability
• MARVEL Intuit™ Integrated Controls ensure precise temperature management from 34°F to 46°F
• Integrated drain system keeps spillage under control and removable components make for easier cleaning
• Low Boy coupler makes it easier to store, tap and swap out tall barrels
• Secure CO2 tank storage area and drain basin
• Close Door Assist System™ gently and automatically closes door
• Panel overlay option features soft-close integrated hinge for a truly flush fit with cabinetry
• Audible and visual alarms signal when door is left ajar to protect food integrity and energy use
• Drain pan and hose, 5 lb. CO2 tank, connectors, regulator and interior floor shield included
• Height adjustment up to 1” with leveling legs
• Built-in and mobile models available with single or twin tap
• All models feature a double insulated stainless steel tower
• 1-year warranty
Storage Capacity
Stores half kegs, tall quarter kegs, pony kegs, sixth barrels, Cornelius kegs, growlers, bottles or cans
Product Dimensions
23⅞” W x 33¾” minimum H x 25 ⅝” D(including handle)
Finish/Door Options
Stainless Steel Wood Overlay(Panel Ready)
Ordering Details
SINGLE TAP, MOBILESolid Black Door, Stainless Handle Single Tap, Right Hinge
ML24BSSMRB
TWIN TAP, MOBILESolid Black Door, Stainless Handle, Twin Tap, Right Hinge
ML24BTSMRB
SINGLE TAP, BUILT-INSolid Black Door, Right Hinge ML24BSS2RBSolid Black Door, Left Hinge ML24BSS2LBSolid Stainless Steel Door, Right Hinge ML24BSS2RS
Solid Stainless Steel Door, Left Hinge ML24BSS2LS
Solid Panel Overlay Ready Door, Integrated Right Hinge
ML24BSP3RP
Solid Panel Overlay Ready Door, Integrated Left Hinge
ML24BSP3LP
TWIN TAP, BUILT-INSolid Stainless Steel Door, Right Hinge ML24BTS2RS
Solid Stainless Steel Door, Left Hinge ML24BTS2LS
Solid Panel Overlay Ready Door, Integrated Right Hinge
ML24BTP3RP
Solid Panel Overlay Ready Door, Integrated Left Hinge
If necessary to gain clearance inside the rough-in opening a hole can be cut through the adjacent cabinet and the power cord routed through this hole to a power outlet. Another way to increase the available opening depth is to recess the power outlet into the rear wall 1" (2.5 cm) to gain the thickness of the power cord plug.
PRODUCT DATA
MODELELECTRICAL
REQUIREMENTS#PRODUCTWEIGHT
ML24BN(S) 115V/60Hz/15A 140 lbs(63.6 kg)
ML24BN(P) 115V/60Hz/15A 140 lbs(63.6 kg)
Figure 7
* Depth dimension of rough-in opening may vary depend-ing on each individual installation. To recess entire door "F" dimension plus 1" (2.5 cm) for thickness of power cord plug is required.
** Minimum rough-in opening required is to be larger than the adjusted height of the cabinet.
# A grounded 15 amp dedicated circuit is required. Follow all local building codes when installing electrical and appli-ance.
PRODUCT DIMENSIONS ML24BN
211⁄2"(54.6cm)Figure 8
Figure 7a
“G” “H” “J”
25 21 ⁄32”(65.2 cm)
46 13⁄32”(117.9 cm)
25 11 ⁄16”(65.2 cm)
Dynamic Cooling Technology™ delivers rapid cool down and the industry’s best temperature stabilityThe distinctive Marvel design features a thermal-efficient cabinet and door combined with Dynamic Cooling Technology™ for superior temperature stability, faster cooling times and speedy temperature recovery even with high frequency.
Front SideFront
ForcedAir Fan
Evaporator Plate
Return Air Intake
Front SideFront
ForcedAir Fan
Evaporator Plate
Return Air Intake
Cabinet Dimensions
"D" "E" "F"
23 7⁄8”(60.7 cm)
33 3⁄4” to 34 3⁄4”(85.7 to 88.3 cm)
23 23⁄32”(60.2 cm)
17
! CAUTION
Material Type #10 Wood Screw Hardwood 1⁄8" (3.2 mm) Diameter. Pilot HoleSoftwood 7⁄64 (2.8 mm) Diameter. Pilot Hole
Table B
Step 5: Install the doorCarefully open the top and bottom hinges on the door being careful as there are many pinch points. Place the hinges over the 4 screws in the cabinet, 2 at the top and 2 at the bottom and slide the door into position. Tighten the 4 hinge screws with a phillips screwdriver. (See Figures 13 and 13a). Place wire harness from the grille and mount to the bottom of the door with the screw and "P" clamp removed in step 1. (See Figure 13b). Reconnect the wire harness, (See Figure 14).
Step 4: Assemble the panel to the doorThe preferred method of attaching the panel to the door is to clamp the panel to the door so it cannot move while drilling the screw pilot holes. Use bar clamps or "C" clamps with pads on the clamping surfaces that will not mar the panel or the door. The custom overlay panel should be flush with the top of the door and centered along the width of the door. See Figure 15a. Drill holes through the gasket extrusion using the 10 holes as pilot holes. Use the drill size from the chart in Table "B", being careful not to drill through the front surface of the panel, drill no deeper than 1⁄2" (12.7 mm) deep. If the overlay panel is thinner than 5⁄8" (16 mm) thick shorter screws will have to be obtained. Fasten the panel to the door with the 10 screws provided in the literature pack. (See Figure 20). Remove the clamps and replace the gasket in the gasket extrusion channels of the door. Some force may be required to seat the gasket into the channels. Be sure the gasket corners are seated properly.
Figure 20
#10 x 1/2"screw
Weight of overlay door panel must not exceed 15 pounds (6.8 kg) for a solid door model.
OVERLAY DOOR PANEL INSTALLATION
17
! CAUTION
Material Type #10 Wood Screw Hardwood 1⁄8" (3.2 mm) Diameter. Pilot HoleSoftwood 7⁄64 (2.8 mm) Diameter. Pilot Hole
Table B
Step 5: Install the doorCarefully open the top and bottom hinges on the door being careful as there are many pinch points. Place the hinges over the 4 screws in the cabinet, 2 at the top and 2 at the bottom and slide the door into position. Tighten the 4 hinge screws with a phillips screwdriver. (See Figures 13 and 13a). Place wire harness from the grille and mount to the bottom of the door with the screw and "P" clamp removed in step 1. (See Figure 13b). Reconnect the wire harness, (See Figure 14).
Step 4: Assemble the panel to the doorThe preferred method of attaching the panel to the door is to clamp the panel to the door so it cannot move while drilling the screw pilot holes. Use bar clamps or "C" clamps with pads on the clamping surfaces that will not mar the panel or the door. The custom overlay panel should be flush with the top of the door and centered along the width of the door. See Figure 15a. Drill holes through the gasket extrusion using the 10 holes as pilot holes. Use the drill size from the chart in Table "B", being careful not to drill through the front surface of the panel, drill no deeper than 1⁄2" (12.7 mm) deep. If the overlay panel is thinner than 5⁄8" (16 mm) thick shorter screws will have to be obtained. Fasten the panel to the door with the 10 screws provided in the literature pack. (See Figure 20). Remove the clamps and replace the gasket in the gasket extrusion channels of the door. Some force may be required to seat the gasket into the channels. Be sure the gasket corners are seated properly.
Figure 20
#10 x 1/2"screw
Weight of overlay door panel must not exceed 15 pounds (6.8 kg) for a solid door model.
OVERLAY DOOR PANEL INSTALLATION
Overlay Panels
14
! CAUTION
15⁄32"(2.9 cm)
Figure 17Right Hand Hinged Door
24" (61 cm) wide appliance
Figure 18Right Hand Hinged Door
24" (61 cm) wide appliance
OVERLAY DOOR PANEL INSTALLATION
1" (2.5 cm) diameter x 1⁄4" (6 mm) deep
4 places
Clearance for hinge
at top and bottom
2"(5.1 cm)
311⁄16"(9.4 cm)
11⁄2"(3.8 cm)typical
1⁄4"(6 mm)Deep
Hin
ge s
ide
of d
oor
Clearance for screw head, 4 places
3011⁄32"(77.1 cm)
111⁄16"(4.3 cm)
233⁄4"(60.3 cm)
31⁄8"(7.9 cm)
Top of door
Step 4: Assemble the panel to the doorThe preferred method of attaching the panel to the door is to clamp the panel to the door so it cannot move while drilling the screw pilot holes. Use bar clamps or "C" clamps with pads on the clamping surfaces that will not mar the panel or the door. The custom overlay panel should be flush with the top of the door and centered along the width of the door. See Figure 10a. Drill holes through the gasket extrusion using the 10 holes as pilot holes. Use the drill size from the chart in Table "C", being careful not to drill through the front surface of the panel, drill no deeper than 1⁄2" (12.7 mm) deep. If the overlay panel is thinner than 5⁄8" (16 mm) thick shorter screws will have to be obtained. Fasten the panel to the door with the 10 screws provided in the literature pack. (See Figure 19a). Remove the clamps and replace the gasket in the gasket extrusion channels of the door. Some force may be required to seat the gasket into the channels. Be sure the gasket corners are seated properly.
Material Type #10 Wood Screw Hardwood 1⁄8" (3.2 mm) Diameter. Pilot HoleSoftwood 7⁄64 (2.8 mm) Diameter. Pilot Hole
Table C
Weight of overlay door panel must not exceed 15 pounds (6.8 kg) for a solid door model or 10 pounds (4.5 kg) for a glass door model.
31⁄8"(7.9 cm)
13⁄4"(4.4 cm)
41⁄8"(10.5 cm)
1⁄4" (6 mm)radius ispermissible
This sideto door
31⁄8"(7.9 cm)
327⁄32"(9.8 cm)
13⁄16"(3 cm)
14"(35.6 cm)
47⁄8"(12.4 cm)
For comprehensive installation instructions, please visit www.marvelrefrigeration.com
16
15⁄32"(2.9 cm)
15⁄32"(2.9 cm)
OVERLAY DOOR PANEL INSTALLATION
Clearance for hinge
at top and bottom
Clearance for hingeat top and bottomClearance for
screw head, 4 places Top of door
Hin
ge s
ide
of d
oor
Clearance for screw head, 4 places
Figure 18Right Hand Hinged Door
24" (61 cm) wide appliance
Figure 16Left Hand Hinged Door
24" (61 cm) wide applianceH
inge
sid
e of
doo
r
Top of door
233⁄4"(60.3 cm)
1⁄4"(6 mm)Deep
233⁄4"(60.3 cm)
1⁄4"(6 mm)Deep
Figure 17Left Hand Hinged Door
24" (61 cm) wide appliance
1" (2.5 cm) diameter x 1⁄4" (6 mm) deep4 places
11⁄2"(3.8 cm)typical
111⁄16"(4.3 cm)
2"(5.1 cm)
311⁄16"(9.4 cm)
Figure 19Right Hand Hinged Door
24" (61 cm) wide appliance
2"(5.1 cm)
311⁄16"(9.4 cm)
11⁄2"(3.8 cm)typical
111⁄16"(4.3 cm)
47⁄8"(12.4 cm)
14"(35.6 cm)
1" (2.5 cm) diameter x 1⁄4" (6 mm) deep
4 places
1⁄4" (6 mm)radius ispermissible
3011⁄32" (77.1 cm)
3011⁄32" (77.1 cm)
13⁄4"(4.4 cm)
31⁄8"(7.9 cm)
13⁄16"(3 cm)
1⁄4" (6 mm)radius ispermissible
47⁄8"(12.4 cm)
13⁄16"(3 cm)
31⁄8"(7.9 cm)
13⁄4"(4.4 cm)
14"(35.6 cm)
This sidefacing interior
This sidefacing interior
16
15⁄32"(2.9 cm)
15⁄32"(2.9 cm)
OVERLAY DOOR PANEL INSTALLATION
Clearance for hinge
at top and bottom
Clearance for hingeat top and bottomClearance for
screw head, 4 places Top of door
Hin
ge s
ide
of d
oor
Clearance for screw head, 4 places
Figure 18Right Hand Hinged Door
24" (61 cm) wide appliance
Figure 16Left Hand Hinged Door
24" (61 cm) wide applianceH
inge
sid
e of
doo
r
Top of door
233⁄4"(60.3 cm)
1⁄4"(6 mm)Deep
233⁄4"(60.3 cm)
1⁄4"(6 mm)Deep
Figure 17Left Hand Hinged Door
24" (61 cm) wide appliance
1" (2.5 cm) diameter x 1⁄4" (6 mm) deep4 places
11⁄2"(3.8 cm)typical
111⁄16"(4.3 cm)
2"(5.1 cm)
311⁄16"(9.4 cm)
Figure 19Right Hand Hinged Door
24" (61 cm) wide appliance
2"(5.1 cm)
311⁄16"(9.4 cm)
11⁄2"(3.8 cm)typical
111⁄16"(4.3 cm)
47⁄8"(12.4 cm)
14"(35.6 cm)
1" (2.5 cm) diameter x 1⁄4" (6 mm) deep
4 places
1⁄4" (6 mm)radius ispermissible
3011⁄32" (77.1 cm)
3011⁄32" (77.1 cm)
13⁄4"(4.4 cm)
31⁄8"(7.9 cm)
13⁄16"(3 cm)
1⁄4" (6 mm)radius ispermissible
47⁄8"(12.4 cm)
13⁄16"(3 cm)
31⁄8"(7.9 cm)
13⁄4"(4.4 cm)
14"(35.6 cm)
This sidefacing interior
This sidefacing interior
15
Magnetic Gasket remove starting at a corner, grasp and pull away from the door.
Step 3: Cut and drill the overlay panelDepending on your model cut the overlay door panel to the dimensions shown in Figures 16 and 17 for a left hand door model or Figures 18 and 19 for a right hand door model.
Overlay panel flush with top
of door.
Holes in gasket
retainer.
Overlay panel to be centered on width of door.
Figure 15
Figure 15a
Step 2: Remove the door gasketWith the door laying on a flat surface and starting at a corner of the door remove the magnetic door gasket from the interior side of the door, see Figure 15. Set the gasket aside on a flat surface.
There are 10 holes in the gasket retainer extrusions, (3 on each side and 2 at the top and bottom which are used to fasten the panel to the front of the door. The screws are provided in the literature pack.
Press and hold down this tab on the wire connector and pull the connector apart.
