QC Industries 513.753.6000
250 Series End Drive Conveyors
92
6.191.89 * 1.81
FRAME
W - .25 = BELT WIDTH
4.44
.42
39.38
W + .31 = FRAME WIDTH
L
DA = (L - D)
1.38 SHAFTLENGTH
.62 DIA.3/16 KEY
W + 4.95
.82
Specifications
Note: As in allindustries, technicalspecifications willchange withtechnology updates.Please contactfactory or seewww.qcindustries.comfor the most up-to-date drawings.
Width 2” to 24”Length 3’ to 15’Profile 1.89” highDrive Pulley 2.5” DiameterLoad Carrying Capacity to 630 lbs.*Speed Range up to 360 fpmBelt is the highest point on the conveyor
Overview Dimensions
*See Technical Data on page 94
•••••••
*Dimension reflects use of MAA belt. See page 100. Note: Conveyors 120” and under are built using a single piece frame
QC Industries 513.753.6000 93
Features & Benefits
Tail Assembly Drive Assembly
Conveyor
• Low profile design provides tight product transfers and the ability to fit into space-constrainedareas
• Single piece 10-gauge steel framework is laser cut and formed to create a single-body frameconstruction, ensuring frame integrity
• Tight tolerance belting and our unique snap-out sealed tail assembly provide for a quick beltchange (less than 5 minutes) that is normally achieved without having to remove the drivepackages or side rails
• High tensile strength belts offer superior strength-to-weight ratio and are available in over 50various types
• All components in our conveyors are produced on state-of-the-art manufacturingequipment
• Multi-point belt tension is achieved through a snap-in eccentric tailassembly designed to pull through the natural elongation characteristics ofthe belt and provide quick and easy belt change capacity
• Crowned sealed tail assembly isdesigned to promote excellent belttracking and is equipped withsuperior needle bearings withseals that are filled with highperformance grease
• Thrust washers designed into thetail assembly provide axial float,which allows the assembly to move with the natural camber of the belt andprotect bearings against off-center load conditions
• Grease fitting design in the tail assembly allows for lubrication of bearingswhile the conveyor is running, resulting in zero down time duringlubrication
• Precision bearing alignment is guaranteed within the pressed tail assembly,providing optimal conditions to move the heaviest loads in low profile conveyors
• Eccentric tracking bushing allows for single point tracking control at theidler ends of the conveyor
• Straight knurl design used to prevent premature wear on the carcassof the belt and still provide superior grip to overcome start-up inertia
• Crowned sealed drive assembly is designed to promote superior belttracking, and is equipped withsuperior sealed ball bearingsthat are filled with highperformance grease
• Thrust washers designed into thedrive assembly back-flexing idlersprovide axial float, allowing theassembly to move with the naturalcamber of the belt and protectbearings against off-center loadconditions
• Grease fitting design in each bearing housing allows for lubrication ofbearings while the conveyor is running, resulting in zero down timeduring lubrication
• Precision bearing alignment is guaranteed within the drive assemblythough self-aligning bearings, providing optimal conditions to move theheaviest loads in low profile conveyors
• Threaded tracking adjustment points provide simple responsive belttracking that retain settings, even during belt removal
250 Series End Drive Conveyors
94 QC Industries 513.753.6000
Load Carrying Capacity - Figure 94-A
Incline/Decline Load Factors - Figure 94-B
Conveyor Friction - Figure 94-C
700
600
500
400
300
200
100
0
Above load carrying capacities are for both drive pushing and pulling applications.Note: for drive pushing applications, decrease load capacity of conveyor by 1/2(except on the 24” conveyor).
2 3 4 6 8 10 12 18 24
3570 52.5
105 10570140
210140
210175
280350
420
630
175175
315
Pushing (Drive Location C&D)Pulling (Drive Location A&B)
Lbs.
Conveyor Belt Width (in.)
Equ
ival
nt L
oad
Con
stan
t
Angle
2.0
1.5
1.0
0.5
0.0
Factor 0.3 0.6 0.8 1.1 1.4 1.65 10 15 20 25 30
0.3
0.6
0.8
1.1
1.4
1.6
Conveyor Width
Frictional Load
Equ
ival
ent L
oad
300
250
200
150
100
50
02 3 4 6 8 10 12 18 24
96 104 112 128 144 160 176 224 272
96
224
272
Technical Data
Each of the myriad of applications that exist requires certain performancecharacteristics from the conveyor. QC Industries has developed a sizingsystem that condenses all of these parameters into a common factor, namelyequivalent load.
A conveyor application that is accumulating a 50 pound load, for example,demands the conveyor to carry more than 50 pounds. As such, we havedeveloped certain factors to add to the load that the conveyor needs to carry.
Follow the five steps below to determine the equivalent load your applicationrequires. The result will then be used to help choose the gear motorarrangement that will provide the correct torque.
Write down the equivalent load on your application data sheet (found inthe back of the catalog). The equivalent load will be needed to properlysize a gear motor for the conveyor.
Next, proceed to the next page to construct the conveyor part number.
1. Nominal Load
Equivalent Load (lbs) SUM (1-4)
Enter the total load in pounds the conveyor must carry. For example, (12)cartons weighing 10 pounds each would have a total nominal load of 120 lbs.Use Figure 94-A to cross-reference the width conveyor you desire with thenominal load you need to carry. Each conveyor width listed shows a total loadcarrying capacity for pushing and pulling applications. The 250 conveyor cancarry 35 pounds per inch of width (with the exception of a 24” wide conveyor,which can carry only 175 lbs.) Enter nominal load (in pounds) on Line One.
If the application does not have an accumulating load, enter zero on LineTwo. Otherwise, multiply the nominal load times an accumulation factor. (0.2for accumulation belts listed on page 100 and 0.3 for MAA standardurethane). Enter Accumulation Factor on Line Two.
Some applications require an incline or decline. If the application does notrequire an incline or decline enter zero on Line Three. For inclining ordeclining applications choose a factor from Figure 94-B based upon theangle of incline, then multiply that factor by the total nominal load fromLine One. The angle limit is 30 degrees. Enter result on Line Three.
**Verify Load Capacity:After adding lines one through four together, please referenceFigure 94-A to ensure that the conveyor width you desire willcarry the sum of Lines One through Three. If the sum isgreater than the load capacity listed for the width you havechosen, please choose a wider conveyor or consult factory.
All conveyors have a certain amount of friction that must be added to thenominal load. To determine how much additional load must be factoredin, add 4 to the conveyor width in inches, then multiply by 6, or simplychoose the value from Figure 94-C. Enter result on Line Four.
lbs.
1.
2. Accumulation 2.
3. Incline/Decline [Factor] x [Load] = 3.
4. Conveyor Friction 4.
104 112 128144
160176
Note: See page 95
STOPSTOP
QC Industries 513.753.6000 95
Step 4
Choose three-digit belt code on page 100.
Example: 2ESBH10-SPF120-ALQ-MAA250 Series End Drive conveyor with standard construction and 1.81” powdercoated frame. Conveyor measures 10” wide by 120” long with solid outputdrive pulley and standard tail pulley. The drive output shaft is in the Aposition. The conveyor has a standard urethane belt.
Step 1
Step 2
Step 3
- - -2 E S H
SeriesD
rive TypeC
onstructionFram
eFram
e StyleW
idthW
idth
LengthLengthLength
Drive LocationD
rive PulleyTail Pulley
Belt
Belt
Belt
2 = 250 E = End Drive S = StandardB = 1.81” Powder Coat (Beige)E = 1.81” Stainless Steel H = Straight Frame
Widths Lengths*2”3”4”6”8”
10”12”18”24”
Drive Location Drive Pulley Type Tail Pulley TypeD
BA
C
*.625” Dia.Cap
Solid Output ShaftL QStandard
Step 1 Step 2 Step 3 Step 4
*Contact factory for special lengths. Lengths 120” and under area single piece frame design.
Frame Frame StyleConstructionDrive TypeSeries
How to Order
A&B are drive pullingC&D are drive pushing
Standa
rd
Standa
rd
As standard, we assemble the conveyor,track the pre-tensioned belt and qualitycheck every conveyor before we ship tothe customer. Conveyors longer than120” ship unassembled. Accessoriessuch as Motors, Stands, Mounts, andGuides are packaged separately andare shipped unassembled with theconveyor to prevent damage duringshipment. Complete assembly can beprovided upon request; please contactour factory for details.
LengthLengthLength
020304060810121824
36”48”60”72”96”
120”132”156”180”
Order CodeSSSSSS011
PPPPPP924
346792333
680260666
FFFFFF604
000001000
---------
Y*.625” Dia.*.625” Dia.
Dual Output
Order Code
Custom colors available - Contact factory
*3/16 square key included
QC Industries 513.753.6000
250 Series Center Drive Conveyors
96
W - .25 = BELT WIDTH
.42
1.89 *1.81
FRAME
4.446.19
54.75
D
W + .31 =FRAME WIDTH
.82
.62 DIA.3/16 KEY 1.38 SHAFT
LENGTH
W + 4.95
L
(L - D) /2 (L - D) /2
Specifications
Note: As in allindustries, technicalspecifications willchange withtechnology updates.Please contactfactory or seewww.qcindustries.comfor the most up-to-date drawings.
• Width 2” to 24”• Length 4’ to 28’• Profile 1.89” high• Drive Pulley 2.5” Diameter• Load Carrying Capacity to 630 lbs.*• Speed Range up to 360 fpm• Belt is highest point on conveyor
Overview Dimensions
*See Technical Data on page 98
Note: Conveyors 120” and under are built using a single piece frame*Dimension reflects use of MAA belt. See page 100.
QC Industries 513.753.6000
FeaturesFeatures & Benefits
97
Tail Assembly Drive Assembly
Conveyor
• Low profile design provides tight product transfers and the ability to fit into space-constrainedareas
• Single piece 10-gauge steel framework is laser cut and formed to create a single-body frameconstruction, ensuring frame integrity
• Tight tolerance belting and our unique snap-out sealed tail assembly provide for a quick beltchange (less than 5 minutes) that is normally achieved without having to remove the drivepackages or side rails
• High tensile strength belts offer superior strength-to-weight ratio and are available in over 50various types
• All components in our conveyors are produced on state-of-the-art manufacturingequipment
• Multi-point belt tension is achieved through a snap-in eccentric tailassembly designed to pull through the natural elongation characteristics ofthe belt and provide quick and easy belt change capacity
• Crowned sealed tail assembly isdesigned to promote excellent belttracking and is equipped withsuperior needle bearings withseals that are filled with highperformance grease
• Thrust washers designed into thetail assembly provide axial float,which allows the assembly to move with the natural camber of the belt andprotect bearings against off-center load conditions
• Grease fitting design in the tail assembly allows for lubrication of bearingswhile the conveyor is running, resulting in zero down time duringlubrication
• Precision bearing alignment is guaranteed within the pressed tail assembly,providing optimal conditions to move the heaviest loads in low profile conveyors
• Eccentric tracking bushing allows for single point tracking control at theidler ends of the conveyor
• Straight knurl design used to prevent premature wear on the carcassof the belt and still provide superior grip to overcome start-up inertia
• Crowned sealed drive assembly is designed to promote superior belttracking, and is equipped withsuperior sealed ball bearingsthat are filled with highperformance grease
• Thrust washers designed into thedrive assembly back-flexing idlersprovide axial float, allowing theassembly to move with the naturalcamber of the belt and protectbearings against off-center loadconditions
• Grease fitting design in each bearing housing allows for lubrication ofbearings while the conveyor is running, resulting in zero down timeduring lubrication
• Precision bearing alignment is guaranteed within the drive assemblythough self-aligning bearings, providing optimal conditions to move theheaviest loads in low profile conveyors
• Threaded tracking adjustment points provide simple responsive belttracking that retain settings, even during belt removal
QC Industries 513.753.6000
250 Series Center Drive Conveyors
98
Technical Data
Load Carrying Capacity - Figure 98-A
Incline/Decline Load Factors - Figure 98-B
Conveyor Friction - Figure 98-C
700
600
500
400
300
200
100
0 2 3 4 6 8 10 12 18 24
70 105 140210
280350
420
630
175
Lbs.
Conveyor Belt Width (in.)
Equ
ival
nt L
oad
Con
stan
t
Angle
2.0
1.5
1.0
0.5
0.0
Factor0
0.0 0.3 0.6 0.8 1.1 1.4 1.65 10 15 20 25 30
0.0
0.3
0.6
0.8
1.1
1.4
1.6
Conveyor Width
Frictional Load
Equ
ival
ent L
oad
300
250
200
150
100
50
02 3 4 6 8 10 12 18 24
96 104 112 128 144 160 176 224 272
96
224
272
Each of the myriad of applications that exist requires certain performancecharacteristics from the conveyor. QC Industries has developed a sizingsystem that condenses all of these parameters into a common factor, namelyequivalent load.
A conveyor application that is accumulating a 50 pound load, for example,demands the conveyor to carry more than 50 pounds. As such, we havedeveloped certain factors to add to the load that the conveyor needs to carry.
Follow the five steps below to determine the equivalent load your applicationrequires. The result will then be used to help choose the gear motorarrangement that will provide the correct torque.
Write down the equivalent load on your application data sheet (found inthe back of the catalog). The equivalent load will be needed to properlysize a gear motor for the conveyor.
Next, proceed to the next page to construct the conveyor part number.
1. Nominal Load
Equivalent Load (lbs) SUM (1-4)
Enter the total load in pounds the conveyor must carry. For example, (12)cartons weighing 10 pounds each would have a total nominal load of 120 lbs.Use Figure 98-A to cross-reference the width conveyor you desire with thenominal load you need to carry. Each conveyor width listed shows a total loadcarrying capacity for pushing and pulling applications. The 250 conveyor cancarry 35 pounds per inch of width (with the exception of a 24” wide conveyor,which can carry only 175 lbs.) Enter nominal load (in pounds) on Line One.
If the application does not have an accumulating load, enter zero on LineTwo. Otherwise, multiply the nominal load times an accumulation factor. (0.2for accumulation belts listed on page 100 and 0.3 for MAA standardurethane). Enter Accumulation Factor on Line Two.
Some applications require an incline or decline. If the application does notrequire an incline or decline enter zero on Line Three. For inclining ordeclining applications choose a factor from Figure 98-B based upon theangle of incline, then multiply that factor by the total nominal load fromLine One. The angle limit is 30 degrees. Enter result on Line Three.
**Verify Load Capacity:After adding lines one through four together, please referenceFigure 98-A to ensure that the conveyor width you desire willcarry the sum of Lines One through Three. If the sum isgreater than the load capacity listed for the width you havechosen, please choose a wider conveyor.
All conveyors have a certain amount of friction that must be added to thenominal load. To determine how much additional load must be factoredin, add (width x 8) + 80, or simply choose the value from Figure 98-C.Enter result on Line Four.
lbs.
1.
2. Accumulation 2.
3. Incline/Decline [Factor] x [Load] = 3.
4. Conveyor Friction 4.
104 112 128144
160176
STOPSTOP
QC Industries 513.753.6000 99
How to Order
Step 4
Choose three-digit belt ordering code on page 100.
Example: 2CSBH18-096D096-ALQ-MAA250 Series Center Drive conveyor with standard construction and 1.81”powder coated frame. Conveyor measures 18” wide by 240” long with solidoutput drive pulley and standard tail pulley. The drive output shaft is in the Aposition. The conveyor has a standard urethane belt.
Step 1
Step 2
Step 3
- - -2 C S H
SeriesD
rive TypeC
onstructionFram
eFram
e StyleW
idthW
idth
Length
LengthLength
Drive LocationD
rive PulleyTail Pulley
Belt
Belt
Belt
2 = 250 C = Center Drive S = StandardB = 1.81” Powder Coat (Beige)E = 1.81” Stainless Steel H = Straight Frame
WidthsLengths*
2”3”4”6”8”
10”12”18”24”
Drive Location Drive Pulley Type Tail Pulley Type
BA*.625” Dia.Cap
Solid Output ShaftL QStandard
Step 1 Step 2 Step 3 Step 4
*Contact factory for special lengths. Lengths 120” and under are a single piece frame design
Frame Frame StyleConstructionDrive TypeSeries
Standa
rd
Standa
rd
As standard, we assemble the conveyor,track the pre-tensioned belt and qualitycheck every conveyor before we ship tothe customer. Conveyors longer than120” ship unassembled. Accessoriessuch as Motor, Stands, Mounts, andGuides are packaged separately andare shipped unassembled with theconveyor to prevent damage duringshipment. Complete assembly can beprovided upon request; please contactour factory for details.
LengthLengthLength
020304060810121824
48”60”72”96”
120”144”168”192”240”288”336”
Order CodeSSSSS000011
PPPPP467924
46792467924
80260802604
FFFFF802604
00001000011
-----------
DDDDDDDDDDD
Length
Y*.625” Dia.*.625” Dia.
Dual Output
Order Code
*3/16 square key included
Custom colors available - contact factory
QC Industries 513.753.6000
250 Series Conveyors
100
High Friction BeltsA. Grey Diamond Top High AdhesionB. Green High Tack PVCC. Black Lateral Grooved High AdhesionD. Black Rough Top High Adhesion
Accumulation Belts (Low Friction)A. White FDA Fabric AccumulatorC. Black Tight Weave AccumulatorD. Grey Textured Urethane AccumulatorE. Green FDA Fabric Accumulator
Heat-Resistant BeltsA. White Silicone Heat ResistorB. White Silicone Translucent ResistorC. Blue Nitrile Heat ResistorD. White Nitrile Heat Resistor
Cut Resistant BeltsA. Standard UrethaneB. Black Dimple Top Cut ResistorC. Rugged Poly Cut Resistor
FDA BeltsA. Standard UrethaneB. Sealed Edge Standard UrethaneC. Pure White FDAD. Woven White FDAE. White FDA Urethane High AdhesionStatic Conductive BeltsA. Textured Carbon ImpregnatedB. Accumulation Static ConductiveC. Low Friction Static ConductiveD. Structured Static ConductiveTranslucent Belts
A. Green Translucent AccumulatorB. FDA Fabric Translucent AccumulatorC. Silicone Translucent Accumulator
Non-Marking BeltsA. Felt Topped Product ProtectorB. Fabric Topped Product ProtectorC. Cotton Topped Product ProtectorD. Black Elastomer Product Protector
Color Contrasting BeltsA. Gray Textured ContrasterB. Smooth Green Urethane ContrasterC. Dark Green PVC ContrasterD. Light Blue Urethane ContrasterE. Smooth Black PVC Contraster
Release Properties BeltsA. Beige Silicone Product ReleaseB. White PVC Product ReleaseC. Textured Silicone Product ReleaseD. Smooth Habilene Product ReleaseE. Smooth Silicone Product ReleaseSpecialty/Profile BeltsA. Negative Pyramid Profile
Chemical Resistant BeltsDue to the broad spectrum of chemicals and percentages of chemical mixtures, QC Industries offers belt selection assistance in chemical application circumstances. Ourapplication specialists will help determine which belt is best suited to withstand the chemicals present as well as the entire scope of the application parameters. This approachdelivers the best possible product for the application.
FAAFABFADFAF
AAAAACAADAAE
HAAHABHADHAE
IABIACIAD
EAAEABEACEAD
UAAUABUACUADUAE
TAATABTAC
PAAPABPACPADPAE
NAANABNACNAD
RAARABRACRADRAE
SAD
SnakeskinMatte
Longitudinal GrooveRough Top
FabricFabric
TexturedFabric
Fine TextureFabric
Coarse StructureSmooth
SmoothDimple TopStructured
SmoothSmooth, Sealed Edge
MatteSmoothSmooth
TexturedRough Texture
SmoothStructured
TexturedFabric
Textured
TexturedSmoothMatteMatte
Smooth
SmoothMatte, SmoothFine Texture
SmoothTextured
Textured
FeltFabricFabricFelt
PVCPVC Soft
PVCPVC
UrethaneUrethane ImpregnatedUrethane ImpregnatedUrethane Impregnated
SiliconeSilicone Impregnated
Nitrile RubberNitrile Rubber
UrethaneHard UrethaneNitrile Rubber
UrethaneUrethaneUrethane
Urethane ImpregnatedUrethane
Urethane ImpregnatedNitrile Rubber
UrethaneNBR Impregnated Fleece
Impregnated PUUrethane Impregnated
Silicone
PVCUrethane
PVCUrethane
PVC
FeltSpun Polyester
CottonPolyester
SiliconeNon-Stick PVC
SiliconeHabileneSilicone
Urethane
Light GreyDark Green
BlackBlack
WhiteBlack
Light GreyDark Green
WhiteWhiteBlueWhite
WhiteBlackBlack
WhiteWhiteWhite
TranslucentWhite
GreyGreen
Dark GreenLight Blue
Black
BlackBlackBlackBlack
Light GreenTranslucentTranslucent
BeigeWhiteWhiteWhiteWhite
White
WhiteWhite
Natural WhiteBlack
NONONONO
HIGHHIGHHIGHHIGH
212212194212
176176158176
NOYESYESYES
0.1030.1450.0830.185
YESNONOYES
NONONONO
YESNONO
YESYESYESYESYES
NONONONO
YESYESYES
NOYESNOYESNO
YESYESYESNO
YESYESNOYESYES
YES
VERY LOWVERY LOWVERY LOWVERY LOW
MEDLOWMEDMED
LOWHIGHMED
LOWLOWLOWMEDHIGH
MEDHIGHLOWMED
VERY LOWVERY LOWVERY LOW
MEDLOWMEDMEDMED
MEDMEDMEDMED
HIGHLOWMEDMEDLOW
MED
212248140175
356356300300
212248176
212212230248176
212212158176
175248176
158176212212212
175175175302
212
212194356176176
176212140175
356356212212
176212176
176176194212176
176212158176
175212176
158176176176176
176158356176176
176
175175175248
YESNOYESYES
YESYESYESYES
YESYESYES
0.0540.0510.0600.054
0.0590.0510.0790.067
0.0750.0830.100
YESYESYESYESYES
NONONO
YESYESYESYESNO
NONONOYES
YESYESYESYESNO
YES
0.0750.0750.0550.0470.050
0.0630.0800.0400.100
0.0230.0240.040
0.0600.0500.0750.0630.071
0.0700.0670.0720.098
0.0720.0590.0590.0900.040
0.078
Top
Surfa
ce D
escr
iptio
n
Top
Surfa
ce M
ater
ial
Belt
Colo
r
FDA
Tops
ide
Coef
ficie
ntof
Fric
tion
(CoF
)Sh
ort T
erm
Par
tM
ax T
empe
ratu
re (°
F)
Max
. Am
bint
Ope
ratin
gTe
mpe
ratu
re (°
F)An
ti-St
atic
Aver
age
Belt
Thic
knes
s (in
ches
)
Belt
Orde
ring
Code
Belt Selection Guide
Multi-Purpose BeltsA. Standard UrethaneB. Option #1-Sealed Edge Standard UrethaneC. Option #3-Perforated Belt
MAAMABMAD
SmoothSmooth, Sealed EdgeSmooth, Perforations
UrethaneUrethaneUrethane
WhiteWhiteWhite
YESYESYES
LOWLOWLOW
212212212
176176176
YESYESYES
0.0750.0750.075
eeee
104
104
105
105
Specifications subject to change - consult factory
QC Industries 513.753.6000 101
QC Industries offers conveyor belting for awide variety of applications and industries.These pages cover a number of the morepopular belts we have provided through theyears. These belts have all been tested at QCIndustries and offer a compatible fit to the 250
Series conveyors. If you have a specific needthat is not covered on these pages, pleasecontact one of our sales engineers directly atthe factory to discuss your applicationparameters.
Chemical Resistant BeltsDue to the wide variety of chemical and percentages of chemical mixtures, QC Industries offers belt selection assistance in these application circumstances. Our applicationspecialists will help determine which belt is best suited to withstand not only the chemicals present, but the entire scope of the application parameters. This approachdelivers the best possible product for the application.
To Order With Conveyor:Please use the three-digit QC belt codenumber for conveyor ordering on pages95 and 99.
Multi-Purpose Belts
High-Friction Belts
Accumulation Belts (Low Friction)
Cut-Resistant Belts
Heat-Resistant Belts
FDA/USDA Belts
Static Conductive Belts
Translucent Belts
Color Contrasting Belts
Non-Marking Belts
Release Properties Belts
Specialty/Profile Belts
MAB
FAA
FAB
FAD
FAF
AAAAAC
AAD
HAA
IAB IACIAD
UAA
EAA
UAB
EABEAC
UACUAD
UAE
EAD
TAA
TAB
TAC
PAAPAB
PACPAD
PAE
NAANAB
NACNAD
RAARAB
RACRAD
RAE
SAD
HAB
MAA
QUICK SHIP! MAD
AAE
HADHAE
250 Series Side & Guide Rails
Note 1: W = nominal belt width in inches * Dimension reflects use of standard urethane belt (MAA) see page 100Note 2: All rails are sold in setsNote 3: Side Rails do not run the full length of conveyor. They are indented 1 11/16” from either end
Custom fixed and flared side rails are available. For heights, consult factory
250-0153 pictured
.46 *
2.35
W - .19
W + 1.06
Aluminum extruded 1/3” high sideswith wear strip
W + 1.06
W + .06
2.22
.33 *
Aluminum extruded 1/3” high sides1/3” Side Rails
To Order:Fill in the last three digits of the partnumber with the nominal conveyorlength in inches.
Ex. 250-0153-048 (Center or End Drive Rail)
To Order:Fill in the last three digits of the partnumber with the nominal conveyorlength in inches.
Ex. 250-0170-024 (Center or End Drive Rail)
Part No. 250-0153-Part No. 250-0170-
250-0178 pictured
W + 1.19
W - .19
1.03 * .88
2.912.03
Aluminum extruded 1” high sideswith wear strip
W + .06
W + 1.19
.93 * .78
2.812.03
Aluminum extruded 1” high sides1” Side Rails
To Order:Fill in the last three digits of the partnumber with the nominal conveyorlength in inches.
Ex. 250-0174-048 (Center or End Drive Rail)
To Order:Fill in the last three digits of the partnumber with the nominal conveyorlength in inches.
Ex. 250-0178-096 (Center or End Drive Rail)
Part No. 250-0174- Part No. 250-0178-
250-0215 pictured
2.03
1.90
W + 1.19
2.05 *
3.93
W - .18
Aluminum extruded 2” high sideswith wear strip
W + .06
W + 1.19
1.93 * 1.78
3.81
2.03
Aluminum extruded 2” high sides2” Side Rails
To Order:Fill in the last three digits of the partnumber with the nominal conveyorlength in inches.
Ex. 250-0215-024 (Center or End Drive Rail)
To Order:Fill in the last three digits of the partnumber with the nominal conveyorlength in inches.
Ex. 250-0216-060 (Center or End Drive Rail)
Part No. 250-0215- Part No. 250-0216-
102 QC Industries 513.753.6000
Fixed Side Rails
QC Industries 513.753.6000
Adjustable Guide Rails
103
2” High 2-Axis Adjustable Guides
W + 9.12 MAX
W + 2.81
4.34
3.00ADJ.
W - .25 MAX.
3.25 MAX. *1.99 MIN. *
W + 2.81
W + 9.12 MAX.
W - .10 MAX.3.00
ADJ.
2.50 MAX. *1.13 MIN. *
1” High 2-Axis Adjustable GuidesPart No. 250-0281-
W + 2.81
W + 9.12 MAX.
4.34
W - .38 MAX.3.00
ADJ.
5.25 MAX. *3.00 MIN. *
3” High 2-Axis Adjustable Guides
W + 1.42
W - 1.21
3.281.62 MAX. *1.03 MIN. *
1” High Indented Guide AssemblyPart No. 250-0219-
3.94
W + 1.57
W - 1.21
2.40 MAX. *2.13 MIN. *
2” High Indented Guide AssemblyPart No. 250-0218-
4.92
3.03 *
W + 1.57
W - 1.31
3” High Indented Guide AssemblyPart No. 250-0222-
2-Axis Adjustable Guides250-0281-048-T pictured
Indented Guides250-0219 pictured
To Order:Fill in the last three digits of part number with the nominallength of the conveyor. Choose a set screw adjustment or athumb wheel adjustment mechanism by indicating (S) for setscrew and (T) for thumb wheel at the end of the part number.
Example 250-0281-120 -T1” adjustable guide rail with wear strip and thumb wheeladjustment for a 120” long conveyor
The 2-Axis Adjustable Guides are designed to guide theproduct being conveyed. The rails can adjust vertically andhorizontally, offering the end user the ultimate in flexibility.Choose from a set screw or thumb wheel adjustment. Thethumb wheel is shown in the above picture and is ideal forquick adjustments, because no tools are required.
To Order:Fill in the last three digits of the part number with the nominalconveyor length in inches.
Example 250-0281-1201” adustable guide rail with wear strip for a 120” longconveyor
- Part No. 250-0282- -
Part No. 250-0283- -
*Dimension reflects use of MAA belt. See page 100
QC Industries 513.753.6000
250 Series Automation Accessories
104
To Order:
LD
Conveyor Length (in inches)
Conveyor Width (in inches)
# of Rails (1, 2, 3, etc)
Rail Clearance Height (2” or 3”)
# of Lanes (2,3,4 etc)Mounting Type (F - Frame or T - Tee slot)
Construction (S - Standard)
ExampleLD-2-08144-12FS2” Lane Divider for 8” wide 144” longconveyor. One rail with two lanesmounted to the conveyor frameLane Dividers Lane Dividers
For part number see box to right
LANES
RAILS
RAIL CLEARANCE 2" OR 3"
S
90O Transfer Plate
Conveyor Width Part No.
125-0230-02125-0230-03125-0230-04125-0230-06125-0230-08125-0230-10125-0230-12125-0230-18125-0230-24
2 in.3 in.4 in.6 in.8 in.10 in.12 in.18 in.24 in.
Note 1: Transfer plates are not intendedfor use with high friction belts.Note 2: Discharge conveyor must bepushingNote 3: Customer to drill screw holes tomount plate
Conveyor Width Part No.
125-0220-02125-0220-03125-0220-04125-0220-06125-0220-08125-0220-10125-0220-12125-0220-18125-0220-24
2 in.3 in.4 in.6 in.8 in.10 in.12 in.18 in.24 in.
Inline Transfer Plate
Note:Transfer plates are not intended for usewith high friction belts
Adjustable Stops
To Order:
1. Select an adjustable stop for 1”sides, 2” sides, or single tee slot(See page 102)
2. Using the chart below, fill in thepart number using the nominal widthof the conveyor for the last two digitsof the part number
Example: 125-0232-04End Stop for a 4” wide conveyor that has1” aluminum side rails
1” Sides2” SidesSingle Tee Slot
125-0232-WW125-0234-WW125-0233-WW
Part No.
Adjustable Diverters
To Order:Part No. 125-0250-000
Note:
The adjustable diverter comes with a5’ piece of UHMW rail and (2)mounting assemblies that the usercan utilize to help orient the productaround a 90O transfer.
QC Industries 513.753.6000 105
Standard Mounts Note:These mounts are intended for surface mounting only. The 250 stands do notrequire a conveyor mount when ordering stands on pages 106 & 107.
To Order:Frame Mounted version attachesdirectly to the conveyor frame. Theframe has mounting holes every 3”.
Part No. 125-0181-04 (Frame)*
Notes:Brackets are universal and can work on either side of the conveyor.
W + 1.71
W + 1.09 MAX.W + .57 MIN.
1.25.135
W + 1.46
3.06
.34 DIA..22 DIA.
1.32
.88.59
.31
3.50
.38SLOT
1.32
1.15
.41
.13
2.06 *
Universal Raised Side Mount
W + 1.46
W + 1.71
W + 1.09 MAX.W + .57 MIN.
.135
1.25
.22 DIA. .34 DIA.
3.50
.38SLOT
4.81
3.07
.88.59
.31
3.10
1.53
.13 5.28 *
To Order:Frame Mounted version attachesdirectly to the conveyor frame. Theframe has mounting holes every 3”.
Part No. 125-0182-04 (Frame)*
Notes:Brackets are universal and can work on either side of the conveyor.
Tee Mount
Notes:Brackets are universal and can work on either side of the conveyor and mountsthe conveyor to a flat surface.
To Order:
Attaches directly to the conveyorframe. The frame has mounting holesevery 3”.
Part No. 125-0010-00*
5/16 DIA.THRU HOLE
.135
W + 2.00
W + 1.37
2.04 *
1.56
4.00
3.00
.66
.22 1.00
1.60
Universal Bottom Mount
Notes:Bottom mount can attach conveyor to a horizontal or vertical surface.Cannot be used with high adhesion belts.
5/16-18SET SCREW
.257 DIA.THRU HOLE
11/32 DIA.
2.89 *
W - 1.50
W + 1.50
W - .75 W + 1.00
.43
.63
1.25 .16 .84
To Order:Attaches directly to the underside ofthe conveyor frame. To order, use thepart number below and fill in thenominal conveyor width in inches forthe last two digits.
Part No. 125-0011-WW *
Universal Adjustable Side Mount
125-0182-04 pictured
*Part No. denotes one bracket andnecessary hardware
*Part No. denotes one bracket andnecessary hardware
*Part No. denotes one bracket andnecessary hardware
*Part No. denotes one bracket andnecessary hardware
Example: 125-0011-04*Universal Bottom mount for a 4” wideconveyor
125-0181-04 pictured
*Dimension reflects use of MAA belt. See pages 100-101.
QC Industries 513.753.6000
250 Series Stands
106
NOTE: There is a 3” overall height adjustment with feet
NOTE: All applications will require the end user to properly lag stands and ensure stability. Because every application and installation is different, thefunctionality and performance of the supports depend on the end user. QC Industries can aid in determining the supports your application requires.
Part No.125-0074-036 (Qty 1)125-0074-036-SET (Qty 4)The Swivel-In Tee Nut is ideal formounting brackets to analuminum stand, and allows quickmounting location changes.1/4 - 20 thread in Tee-Nut is providedfor attaching accessories
To order:
Swivel-In T Nut
To order:Aluminum Cross Ties
Example:125-0235-024
Part No.125 - 0235 -
Cross Ties - Available LengthsLLL
Enter length of cross ties needed into the “LLL”section above. A quantity of one includes (2) crossties. Note: Cross ties require customer to cut tolength because of stand placement variations.
Inches24”36”48”60”72”96”
120”144”
LLL024036048060072096120144
Part No. 125-0122-04Swivel locking casterOrder (2) per standCasters can be added to eitheraluminum or steel stands. Swivellocking casters increase standheight by 5.50”.Casters should only be used withstands that are 1/3 as wide asthey are tall.
Casters are not recommended onmulti-frame conveyors.
To order:
Casters
To be used in conjunction with the aluminum standsat the top of the page. See opposing page fortypical layouts
WW
H1 - H2
Stand Height Range: H1- H2 (in inches)
Stand Widths-WW (nominal conveyor width in inches)
06 - 0909 - 1212 - 1515 - 1818 - 2121 - 2424 - 2727 - 3030 - 33
33 - 3636 - 3939 - 4242 - 4545 - 4848 - 5151 - 5454 - 5757 - 60
02 03 04 06 08 10 12 18 24
H1 - H2H1 - H2
See the next page for table of part numbers
NOTE: No additional mounts are required. The mounts areincluded with the stand but are specific to where the stand isattached to the conveyor. See opposing page.
NOTE: Conveyors 4” wide and under will have the standframework on the outside of the conveyor; and the minimumheight range is 12 - 15 inches
To order:Aluminum Exact Width Conveyor Stands
There are three different stand types.
QC Industries 513.753.6000 107
To Order:1) Choose the height rangefrom the left and enter intoH1 & H2 section of the partnumber
2) Enter the conveyor widthinto the WW section
3) If the conveyor is over120” in length, it will beconstructed in sections.Those sections are denotedon the conveyor orderingpage (pg. 95 or 99). Place astand at each frame joint.Denote those stands byadding the suffix FJ to thestand part number.
4) End drive 250’s require astand at the drive. Denotethis stand by adding thesuffix DS to the stand partnumber.
End Drive Typical Stand Layout
Center Drive Typical Stand Layout
Drive Support Stand
Prefix
0182DS-
0182DS-
0182DS-
0182DS-
0182DS-
0182DS-
0182DS-
0182DS-
0182DS-
0182DS-
0182DS-
0182DS-
0182DS-
0182DS-
0182DS-
0182DS-
H1-H2*
12-15
15-18
18-21
21-24
24-27
27-30
30-33
33-36
36-39
39-42
42-45
45-48
48-51
51-54
54-57
57-60
WW**
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
Frame Joint Stand
Prefix
0182FJ-
0182FJ-
0182FJ-
0182FJ-
0182FJ-
0182FJ-
0182FJ-
0182FJ-
0182FJ-
0182FJ-
0182FJ-
0182FJ-
0182FJ-
0182FJ-
0182FJ-
0182FJ-
0182FJ-
0182FJ-
H1-H2*
06-09
09-12
12-15
15-18
18-21
21-24
24-27
27-30
30-33
33-36
36-39
39-42
42-45
45-48
48-51
51-54
54-57
57-60
WW**
see below¹
see below¹
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
NOTE: All applications will require the end user to properly lag stands and ensure stability. Because every application and installation is different, thefunctionality and performance of the supports depend on the end user. QC Industries can aid in determining the supports your application requires.
NOTE: The conveyor profile adds 1.89” to the overall height
03 04 06 08 10 12 18 24
Example: 0182-27-30-10
Example: 0182FJ-27-30-10
Example: 0182DS-27-30-10
Frame Joint Stand
Drive Support Stand
Example: 0182DS-33-36-12Example: 0182FJ-33-36-12Example: 0182-33-36-12
Frame Joint Stand Frame Joint Stand
Example: 0182-33-36-18 Example: 0182FJ-33-36-18 Example: 0182-33-36-18
* Conveyor adds 1.89” to theoverall height
Prefix
0182-
0182-
0182-
0182-
0182-
0182-
0182-
0182-
0182-
0182-
0182-
0182-
0182-
0182-
0182-
0182-
0182-
0182-
0182-
Aluminum Exact Width Stand
H1-H2*
03-06
06-09
09-12
12-15
15-18
18-21
21-24
24-27
27-30
30-33
33-36
36-39
39-42
42-45
45-48
48-51
51-54
54-57
57-60
WW**
see below¹
see below¹
see below¹
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
see below
02
**WW (Conveyor Width)
¹Not compatible with the followingconveyor widths: 2”, 3”, 4”
250 Series Drives
108 QC Industries 513.753.6000
Service Factor - Chart 108-A
Serv
ice
Fact
or
5 10 7020 30 40 50 60
Drive Sizing Technical Data
The equivalent load was determined in the conveyor technical data pages (pages 94 & 98). To choose a gear motor combination that works bestfor the application, the next step is to convert that equivalent load into the torque required and size a drive based upon its use. The user mustknow the belt speed (in feet per minute), service factor (determined below), and the duty cycle of the application. The steps below guide the userthrough this process. These steps will utimately compare the torque required to move the load on the conveyor (Required Conveyor DriveTorque) and the torque the drive train is capable of producing (Supplied Drive Train Torque).
1. Calculate Required Conveyor Drive Torque (RCDT)
Enter the equivalent load determined on page 94 or 98. Divide this number by 2. The resultequals the torque required for the application, or the required conveyor drive torque (RCDT). Enter RCDT on Line One.
Choose the belt speed from one of the following pages to write down the drive train torque (DTT) for theselected speed. Please note that there are two gearbox types listed; standard and high capacity, for each speed.Enter the drive train torque on Line Two.
Use Chart 108-A below, based upon the hours of operation per day as well as starts and stops per hour. Enterthe result on Line Three.
Divide the drive train torque (DTT) from #2 by the service factor (SF) from #3. This result equals the supplieddrive train torque (SDTT). Enter the result on Line Four.
Compare Line 4 (the supplied drive train torque[SDTT]) to Line 1 (the required conveyor drive torque[RCDT]). If the SDTT is equal to or greater than RCDT,then you have selected the proper drive. SDTT >RCDT. If not, then:
A) Slow down the belt speedB) Choose high capacity gearboxC) Choose a wider conveyorD) Consult factory
Proceed to the next page for instructions on how touse the remaining drive pages.
1.
2. Select Belt Speed & Enter Drive Train Torque (DTT) 2.
3. Enter Service Factor (SF) 3.
4. Calculate Supplied Drive Train Torque (SDTT) 4.
5. Determine Functionality
Starts and Stops per Hour
Hours of Operation per Day
1.8
1.7
1.6
1.5
1.4
1.4
1.3
1.2
1.1
1.0
80 90 100
24 16 8 2
Example:
Equivalent load = 150 (per conveyor technical data page)150 / 2 = 75 (RCDT)30 FPM (From page 111 - end drive)169 inch lbs. of torque (DTT) (Standard capacity gearbox)8 hours per day with no starts and stops (Service Factor is 1.2)169 / 1.2 = 140 inch lbs. (SDTT)
RCDT = 75SDTT = 140
140 75 (Gearmotor assembly will provide adequate torque)
Example:
Equivalent load = 250 (per conveyor technical data page)250 / 2 = 125 (RCDT)100 FPM (From page 113 - center drive)181 inch lbs. of torque (DTT) (High Capacity Gearbox)16 hours per day with (10) starts and stops (Service Factor is 1.5)181 / 1.5 = 121 inch lbs. (SDTT)
RCDT = 125SDTT = 121
121 < 125 (Gearmotor assembly will not provide adequate torque)
2.1
2.0
1.9
1.8
1.7
1.6
1.5
1.4
1.3
1.2
Factor
QC Industries 513.753.6000 109
How to Use the Following Pages
The following pages contain information on types and locations of available QC drives, presented in a clear, concise manner.Simply follow the two-page spread from left to right, and note the steps listed here.
Voltage
Step 1:Choose an end orcenter drive (end drivepages 110 & 111,center drive pages 112& 113)
Step 2:Choose mountingarrangement & drivelocation
Step 3:Choose a speed
Step 4:Run drive sizingcalculations listed onpage 108
Step 5:Choose standard orhigh capacity gearbox.Note: Each speed hastwo rows. The top rowis a standard capacitygearbox, and thebottom is a highcapacity gearbox.Some speed andgearbox selections willhave two differenthorsepower motors.
Step 6:Choose voltagerequirements
Step 7:Put together two partnumbers, motormounting package andmotor by following fromleft to right
Step 3
Step 5
Sizing Information Mounting Part Number Motor Part No. Motor Information
Ratio
50
40
30
Voltage
1,3,V, D-
1,3,V, D-
1,3,V, D-
Prefix
16
16
16
GMtr.Sprocket Belt/ChainGearbox
SizePosition*MountingPrefixConv
SprocketGearboxHand
G or J
G or J
G or J
FPM* HP
1/6
1/6
1/6
Face
42C
42C
42C
Heavy Duty Electric - Fixed or Variable Speed - End Drive
115/230Amp
3.6/1.9
3.6/1.9
3.6/1.9
230/460Amp1.3/.6
1.3/.6
1.3/.6
DCAmp1.7
1.7
1.7
15
20
25
30
40
50
60
75
80
90
100
110
115
120
125
150
1853171862592043211692661442871703591412971703711603491403078618111825711024071150102224128253120
Torque (DTT)Inch Lbs.
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
G
0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
22
22
22
25
22
22
25
22
22
25
32
28
28
34
30
22
34
32
34
32
32
34
32
34
32
32
25
30
28
22
28
34
162516332550255033753375337525503375337525503375501H50
1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-13V D-
303020201515151510101010101015151010101015151010050505
G or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or J
1/61/41/61/31/41/21/41/21/33/41/33/41/33/41/41/21/33/41/33/41/41/21/33/41/21
1/2
3.6/1.94.6/2.63.6/1.97.2/3.64.6/2.68.8/4.44.6/2.68.8/4.47.2/3.610.6/5.37.2/3.610.6/5.37.2/3.610.6/5.34.6/2.68.8/4.47.2/3.610.6/5.37.2/3.610.6/5.34.6/2.68.8/4.47.2/3.610.6/5.38.8/4.412.4/6.28 8/4 4
1.3/.61.3/.61.3/.61.6/.81.3/.62.0/1.01.3/.62.0/1.01.6/.83/1.51.6/.83/1.51.6/.83/1.51.3/.62.0/1.01.6/.83/1.51.6/.83/1.51.3/.62.0/1.01.6/.83/1.5
2.0/1.03.4/1.72 0/1 0
1.72.51.73.52.55
2.55
3.57.63.57.63.57.62.55
3.57.63.57.62.55
3.57.65105
42C42C42C42C42C56C42C56C42C56C42C56C42C56C42C56C42C56C42C56C42C56C42C56C56C56C56C
Example: M2-C1G0-8M2234 Example: 253-15G Voltage
Step 6
Speed
Torque
SizingInfo
DriveLocation
Step 2
QC Industries 513.753.6000 111
250 Series
Sizing Information Mounting Part Number Motor Part No. Motor Information
*Speeds Vary +/- 4 FPM *See drive position chart
Mounting Part Number Example:M2-E3J3-8M3225 (End Mounting Pkg w/high capacity gearbox)
1. ALL above gearmotors are UL and CSA approved2. Torque values are based upon start-up torque3. Inverter duty variable frequency rated motors are available in 1/2, 3/4, and 1 HP. Add an ID to the end of the part number.4. Please note that all inverter duty motors have a non-removable foot mount on them
Notes:
Ratio
50
40
30
Voltage
1,3,V, D-
1,3,V, D-
1,3,V, D-
Prefix
16
16
16
GMtr.Sprocket Belt/ChainGearbox
SizePosition*MountingPrefixConv
SprocketGearboxHand
G or J
G or J
G or J
FPM* HP
1/6
1/6
1/6
Face
42C
42C
42C
Motor Part No. Example:1H3-05J (230/460VAC 1HP Gearmotor@300 FPM)
Heavy Duty Electric - Fixed or Variable Speed - End Drive
115/230Amp
3.6/1.9
3.6/1.9
3.6/1.9
230/460Amp1.3/.6
1.3/.6
1.3/.6
DCAmp1.7
1.7
1.7
15
20
25
30
40
50
60
75
80
90
100
110
115
120
125
150
160
180
220
230
250
300
340
360
1853171862592043211692661442871703591412971703711603491403078618111825711024071150102224128253120239106210881768316477153641285711353106
Torque (DTT)Inch Lbs.
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
E
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
22
22
22
25
22
22
25
22
22
25
32
28
28
34
30
22
22
25
28
28
30
32
32
34
34
32
34
32
32
34
32
34
32
32
25
30
28
22
28
34
32
32
30
28
28
25
22
22
162516332550255033753375337525503375337525503375501H501H501H501H501H501H501H501H501H
1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-
303020201515151510101010101015151010101015151010050505050505050505050505050505050505
G or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or JG or J
1/61/41/61/31/41/21/41/21/33/41/33/41/33/41/41/21/33/41/33/41/41/21/33/41/21
1/21
1/21
1/21
1/21
1/21
1/21
1/21
1/21
3.6/1.94.6/2.63.6/1.97.2/3.64.6/2.68.8/4.44.6/2.68.8/4.47.2/3.610.6/5.37.2/3.610.6/5.37.2/3.610.6/5.34.6/2.68.8/4.47.2/3.610.6/5.37.2/3.610.6/5.34.6/2.68.8/4.47.2/3.610.6/5.38.8/4.412.4/6.28.8/4.412.4/6.28.8/4.412.4/6.28.8/4.412.4/6.28.8/4.412.4/6.28.8/4.412.4/6.28.8/4.412.4/6.28.8/4.412.4/6.28.8/4.412.4/6.2
1.3/.61.3/.61.3/.61.6/.81.3/.62.0/1.01.3/.62.0/1.01.6/.83/1.51.6/.83/1.51.6/.83/1.51.3/.62.0/1.01.6/.83/1.51.6/.83/1.51.3/.62.0/1.01.6/.83/1.5
2.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.72/0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.7
1.72.51.73.52.55
2.55
3.57.63.57.63.57.62.55
3.57.63.57.62.55
3.57.6510510510510510510510510510
42C42C42C42C42C56C42C56C42C56C42C56C42C56C42C56C42C56C42C56C42C56C42C56C56C56C56C56C56C56C56C56C56C56C56C56C56C56C56C56C56C56C
Example: M2-C1G0-8M2234 Example: 253-15G Voltage
115 VAC 1 PH230/460 VAC 3 PH90 VDC w/controller90 VDC w/o controller
Voltage KeyFor optional AC controls, see p. 38For optional AC controls, see p. 38See controller on p. 38Customer to supply controller
13VD
See Drive Accessories pages (p. 114)for optional controllers, motor starters,e-stops, cords, switches, and plugs
QC Industries 513.753.6000
250 Series End Drive
110
A0A3
OB0OB3
-.04 .78
3.6410.94
//
1.89
C0C3
13.34
Drive Location1G
3J1G
3J
End Drive
A0 11.39 10.48 11.38 12.38 12.41 12.31 12.17 12.40 13.27 13.85 13.22 15.84 14.08
161 163 16V 251 253 25V 331 333 33V 501 503 50V 503ID 751 753 75V 753ID 1001 1003 100V 1003ID
A3 12.18 12.18 12.19 13.26 13.26 13.13 13.26 13.26 14.06 13.85 13.22 15.84 14.08 15.19 13.26 15.63 13.50 15.19 14.19 16.51 13.76
B0 5.20 4.69 4.98 5.19 5.20 4.99 6.20 5.20 5.01 6.15 6.19 4.98 7.23
B3 6.78 6.78 4.68 6.19 6.19 4.68 6.19 6.19 4.68 6.15 6.19 4.98 7.23 7.19 6.19 6.13 6.76 7.19 7.19 6.13 8.18
Note:
If your application requires a standardcapacity gearbox, use the A0, B0, or C0dimensions. If it uses a high capacitygearbox, use the A3, B3, C3 dimensions.
Reference these drawings and the tablebelow
Motor Dimension Chart
C0 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82
C3 6.56 6.56 6.56 6.56 6.56 6.56 6.19 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56
Step 1
115VAC 1 PH
230/460 VAC 3 PH
90 VDC w/controller
90 VDC w/o controller
Voltage Key
1
3
V
D
QC Industries 513.753.6000
250 Series End Drive
110
A0 A3
B0 DIA.B3 DIA.
D0 D3
10.94
3.64
1.89 *
7.83 C0 C3
13.34
Drive Location1G
3J1G
3J
End Drive
A0 11.39 10.48 11.38 12.38 12.41 12.31 12.17 12.40 13.27 13.85 13.22 15.84 14.08
161 163 16V 251 253 25V 331 333 33V 501 503 50V 503ID 751 753 75V 753ID 1H1 1H3 1HV 1H3ID
A3 12.18 12.18 12.19 13.26 13.26 13.13 13.26 13.26 14.06 13.85 13.22 15.84 14.08 15.19 13.26 15.63 13.50 15.19 14.19 16.51 13.76
B0 5.20 4.69 4.98 5.19 5.20 4.99 6.20 5.20 5.01 6.15 6.19 4.98 7.23
B3 6.78 6.78 4.68 6.19 6.19 4.68 6.19 6.19 4.68 6.15 6.19 4.98 7.23 7.19 6.19 6.13 6.76 7.19 7.19 6.13 8.18
Note:
If your application requires a standardcapacity gearbox, use the A0, B0, C0, andD0 dimensions. If it uses a high capacitygearbox, use the A3, B3, C3, and D3dimensions.
Reference these drawings and the tablebelow
Motor Dimension Chart
C0 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82
C3 6.56 6.56 6.56 6.56 6.56 6.56 6.19 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56
D0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
D3 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78
QC Industries 513.753.6000
Sizing Information Mounting Part Number Motor Part No. Motor Information
*Speeds Vary up to +/- 4 FPM *See Drive Location chart
Mounting Part Number Example:M2-C3J3-8M3225 (250 Mounting Pkg w/high capacity gearbox)
1. ALL above gearmotors are UL and CSA approved2. Torque values are based upon running torque3. Inverter duty variable frequency rated motors are available in 1/2, 3/4, and 1 HP. Add an ID to the end of the part number.4. Please note that all inverter duty motors have a non-removable foot mount on them
Notes:
Ratio505040403030
Voltage1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-
Prefix
161616161616
GMtr.Sprocket BeltGearbox
SizePosition*MountingPrefixConv
SprocketGearbox
HandG or J
G3 or J3G or J
G3 or J3G or J
G3 or J3
FPM* HP1/61/61/61/61/61/6
Motor Part No. Example:1H3-05J3 (230/460VAC 1HP Gearmotor@300 FPM)
Heavy Duty Electric - Fixed or Variable Speed - 250 Drive
115/230Amp
3.6/1.93.6/1.93.6/1.93.6/1.93.6/1.93.6/1.9
230/460Amp
1.3/0.61.3/0.61.3/0.61.3/0.61.3/0.61.3/0.6
DCAmp1.71.71.71.71.71.7
15
20
25
30
40
50
60
75
80
90
100
110
115
120
125
150
160
180
220
230
250
300
340
360
1853171862592043211692661442871703591412971703711603491403078618111825711024071150102224128253120239106210881768316477153641285711353106
Torque (DTT)Inch Lbs.
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
22
22
22
25
22
22
25
22
22
25
32
28
28
34
30
22
22
25
28
28
30
32
32
34
34
32
34
32
32
34
32
34
32
32
25
30
28
22
28
34
32
32
30
28
28
25
22
22
162516332550255033753375337525503375337525503375501H501H501H501H501H501H501H501H501H
1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-
303020201515151510101010101015151010101015151010050505050505050505050505050505050505
G or JG3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3
1/61/41/61/31/41/21/41/21/33/41/33/41/33/41/41/21/33/41/33/41/41/21/33/41/21
1/21
1/21
1/21
1/21
1/21
1/21
1/21
1/21
42C56C42C56C42C56C42C56C42C56C42C56C42C56C42C56C42C56C42C56C42C56C42C56C56C56C56C56C56C56C56C56C56C56C56C56C56C56C56C56C56C56C
Example: M2-C1G0-8M2234 Example: 253-15G Voltage
115 VAC 1 PH230/460 VAC 3 PH90 VDC w/controller90 VDC w/o controller
Voltage KeyFor optional AC controls, see p. 114For optional AC controls, see p. 114See controller on p. 114Customer to supply controller
13VD
See Drive Accessories (pages 114-115)for optional controllers, motor starters,e-stops, cords, switches, and plugs
111
Face425642564256
1.3/0.62.1/1.01.3/0.61.5/0.72.1/1.02.0/1.02.1/1.02.0/1.01.5/0.7
1.11.5/0.7
1.11.5/0.7
1.12.1/1.02.0/1.01.5/0.7
1.11.5/0.7
1.12.1/1.02.0/1.01.5/0.7
1.12.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.7
1.74.81.73.24.85
4.85
3.27.63.27.63.27.64.85
3.27.63.27.64.85
3.27.6510510510510510510510510510
3.6/1.97.4/3.73.6/1.95.2/2.87.4/3.78.8/4.47.4/3.78.8/4.45.2/2.810.8/5.45.2/2.810.8/5.45.2/2.810.8/5.47.4/3.78.8/4.45.2/2.810.8/5.45.2/2.810.8/5.47.4/3.78.8/4.45.2/2.810.8/5.48.8/4.42.8/1.48.8/4.42.8/1.48.8/4.42.8/1.48.8/4.42.8/1.48.8/4.42.8/1.48.8/4.42.8/1.48.8/4.42.8/1.48.8/4.42.8/1.48.8/4.42.8/1.4
QC Industries 513.753.6000
250 Series Center Drive
112
Center Drive
A0 A3
B0 DIA.B3 DIA.
D0 D3
10.94
3.64
1.89 *
7.83 C0 C3
13.34
Drive Location
3J1G
Note:
If your application requires a standardcapacity gearbox, use the A0, B0, C0, andD0 dimensions. If it uses a high capacitygearbox, use the A3, B3, C3, and D3dimensions.
Reference these drawings and the tablebelow
A0 11.39 10.48 11.38 12.38 12.41 12.31 12.17 12.40 13.27 13.85 13.22 15.84 14.08
161 163 16V 251 253 25V 331 333 33V 501 503 50V 503ID 751 753 75V 753ID 1H1 1H3 1HV 1H3ID
A3 12.18 12.18 12.19 13.26 13.26 13.13 13.26 13.26 14.06 13.85 13.22 15.84 14.08 15.19 13.26 15.63 13.50 15.19 14.19 16.51 13.76
B0 5.20 4.69 4.98 5.19 5.20 4.99 6.20 5.20 5.01 6.15 6.19 4.98 7.23
B3 6.78 6.78 4.68 6.19 6.19 4.68 6.19 6.19 4.68 6.15 6.19 4.98 7.23 7.19 6.19 6.13 6.76 7.19 7.19 6.13 8.18
Motor Dimension Chart
C0 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82 5.82
C3 6.56 6.56 6.56 6.56 6.56 6.56 6.19 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56 6.56
D0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0
D3 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78 .78
QC Industries 513.753.6000 113
Sizing Information Mounting Part Number Motor Part No. Motor Information
*Speeds Vary up to +/- 4 FPM *See Drive Location chart
Mounting Part Number Example:M2-C3J3-8M3225 (250 Mounting Pkg w/high capacity gearbox)
1. ALL above gearmotors are UL and CSA approved2. Torque values are based upon running torque3. Inverter duty variable frequency rated motors are available in 1/2, 3/4, and 1 HP. Add an ID to the end of the part number.4. Please note that all inverter duty motors have a non-removable foot mount on them
Notes:
Ratio505040403030
Voltage1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-
Prefix
161616161616
GMtr.Sprocket BeltGearbox
SizePosition*MountingPrefixConv
SprocketGearbox
HandG or J
G3 or J3G or J
G3 or J3G or J
G3 or J3
FPM* HP1/61/61/61/61/61/6
Motor Part No. Example:1H3-05J3 (230/460VAC 1HP Gearmotor@300 FPM)
Heavy Duty Electric - Fixed or Variable Speed - 250 Drive
115/230Amp
3.6/1.93.6/1.93.6/1.93.6/1.93.6/1.93.6/1.9
230/460Amp1.3/.61.3/.61.3/.61.3/.61.3/.61.3/.6
DCAmp1.71.71.71.71.71.7
15
20
25
30
40
50
60
75
80
90
100
110
115
120
125
150
160
180
220
230
250
300
340
360
1853171862592043211692661442871703591412971703711603491403078618111825711024071150102224128253120239106210881768316477153641285711353106
Torque (DTT)Inch Lbs.
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
M2-
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
1G or 3J
0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-0-3-
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
8M
22
22
22
25
22
22
25
22
22
25
32
28
28
34
30
22
22
25
28
28
30
32
32
34
34
32
34
32
32
34
32
34
32
32
25
30
28
22
28
34
32
32
30
28
28
25
22
22
162516332550255033753375337525503375337525503375501H501H501H501H501H501H501H501H501H
1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-1,3,V, D-
303020201515151510101010101015151010101015151010050505050505050505050505050505050505
G or JG3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3G or J
G3 or J3
1/61/41/61/31/41/21/41/21/33/41/33/41/33/41/41/21/33/41/33/41/41/21/33/41/21
1/21
1/21
1/21
1/21
1/21
1/21
1/21
1/21
3.6/1.97.4/3.73.6/1.95.2/2.87.4/3.78.8/4.47.4/3.78.8/4.45.2/2.810.8/5.45.2/2.810.8/5.45.2/2.810.8/5.47.4/3.78.8/4.45.2/2.810.8/5.45.2/2.810.8/5.47.4/3.78.8/4.45.2/2.810.8/5.48.8/4.42.8/1.48.8/4.42.8/1.48.8/4.42.8/1.48.8/4.42.8/1.48.8/4.42.8/1.48.8/4.42.8/1.48.8/4.42.8/1.48.8/4.42.8/1.48.8/4.42.8/1.4
1.3/0.62.1/1.01.3/0.61.5/0.72.1/1.02.0/1.02.1/1.02.0/1.01.5/0.7
1.11.5/0.7
1.11.5/0.7
1.12.1/1.02.0/1.01.5/0.7
1.11.5/0.7
1.12.1/1.02.0/1.01.5/0.7
1.12.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.72.0/1.03.4/1.7
1.74.81.73.24.85
4.85
3.27.63.27.63.27.64.85
3.27.63.27.64.85
3.27.6510510510510510510510510510
42C56C42C56C42C56C42C56C42C56C42C56C42C56C42C56C42C56C42C56C42C56C42C56C56C56C56C56C56C56C56C56C56C56C56C56C56C56C56C56C56C56C
Example: M2-C1G0-8M2234 Example: 253-15G Voltage
115 VAC 1 PH230/460 VAC 3 PH90 VDC w/controller90 VDC w/o controller
Voltage KeyFor optional AC controls, see p. 114For optional AC controls, see p. 114See controller on p. 114Customer to supply controller
13VD
See Drive Accessories (pages 114-115)for optional controllers, motor starters,e-stops, cords, switches, and plugs
Face425642564256
250 Series Drive Accessories
114 QC Industries 513.753.6000
2X .88 DIA. 2.50
1.253.45
8.00
6.00
5.00
5.00
3X .19 DIA.
Specifications/Features:
115 V AC, 1 phase input, 90 V DC, 1/2 hp max output230 V AC, 1 phase input, 180 V DC, 1 hp max output30:1 speed rangeUL/ULc/CENEMA 1 EnclosureForward/Reverse switch, Run/Brake switchMin/Max & Accel/Decel settings
To Order:Part Number:125-0054-01 Standard NEMA 1DC Control125-0149-09* Wiring: cords & plugs
*Includes 8’ cord from control to AC plug and 8’ cord fromcontrol to motor with male/female disconnects (wired).
Motor Controls
Standard DC Control
4X .18 DIA.
4.45
5.13
.34
2.84
2.40
4.57 5.73
Specifications/Features:115/230 V AC, 1/3 phase, 50/60 hz input, 1 hp max output10:1 speed range (when used with ID motor)UL/ULc/CEIP 20 Enclosure3-digit LED displayForward/Reverse switchRun/Stop button, Accel/Decel buttonsCarrier frequency selectable for quiet operation
To Order:Part Number:*125-0054-5C-11-05 115V AC, 1 phase input, IP20125-0054-5C-21-05 230V AC, 1 phase input, IP20125-0054-5C-23-20 230 V AC, 3 phase input, IP20125-0054-5C-43-10 460 V AC, 3 phase input, IP20
Standard AC Control
2X 3/4 NPT
4.56
7.20 6.35.85
.19
5.63
5.16
2.20 1.20
2.12
Specifications/Features:
115 V AC, 1 phase input, 90 V DC, 1 hp max output230 V AC, 1 phase input, 180 V DC, 2 hp max output30:1 speed rangeUL/ULc/CENEMA 4X EnclosureSpeed adjustment potentiometerForward/Off/Reverse switchMin/Max & Accel/Decel settings
To Order:Part Number:125-0054-38 NEMA 4X DC Control
This 4X washdown controller can be used in a wet or dustyenvironment. Washdown DC Control
2X 3/4 NPT
4.56
7.20 6.35.85
.19
5.63
5.16
2.20 1.20
2.12
Specifications/Features:
115/230 V AC, 1 phase, 50/60 hz input, 3 phase out, 1 hp max output10:1 speed range (when used with ID motor)UL/ULcNEMA 4X EnclosureSpeed adjustment potentiometerRun/Stop switchCarrier frequency selectable for quiet operation
To Order:Part Number:125-0054-37 NEMA 4X AC Control
This 4X washdown controller can be used in a wet or dustyenvironment. Washdown AC Control
Note: It is the responsibility of the end user to properlywire this controller to the gearmotor
Note: It is the responsibility of the end user to properlywire this controller to the gearmotor
Note: It is the responsibility of the end user to properlywire this controller to the gearmotor
Note: It is the responsibility of the end user to properlywire this controller to the gearmotor
QC Industries 513.753.6000 115
Motion Controls
Optional Cords, Plugs, & Switches
Heavy Duty Motor Options
Part Number125-0149-05125-0149-06125-0149-07125-0149-09
DescriptionON/OFF switch for 1 PH heavy duty motorFORWARD/REVERSE switch for 1 PH heavy duty motor8’ cord and plug for 1 PH heavy duty motor8’ cord and plug for 90VDC motor - see controller for details
4X 1/2 DIA. KNOCKOUT
3.63
5.75
2.00
.72
.25 DIA.
5.13
The Motor Starter is an overload protection that alsoprovides a means of using a Remote E-Stop for safety.The starter is equipped with an undervoltage trip toprotect against autostarting after the overload conditionhas been corrected. Also includes short circuit protection.
Specifications/Features:115 V AC, 1 phase, 60 hz input, 1/2 hp max230 V AC, 3 phase input, 1 1/2 hp max460 V AC, 3 phase input, 1 1/2 hp maxUL/CSA/CEStart/Stop buttonsIP55 Enclosure
To Order:Part Number:125-0054-38-115 115 V AC, 1ph w/enclosure125-0054-38-230 230 V AC, 3 ph w/enclosure125-0054-38-460 460 V AC, 3 ph w/enclosure
Motor Starter
LOCK-OUTTAG-OUT
TURN TO RELEASEE-STOP
5.88
2.50
2.25
3.13
The E-Stop accessory is mounted directly to the MotorStarter enclosure, providing a means of stopping the motorfor safety. It can be padlocked for servicing, and contains astart button for restarting the motor after the pushbuttonhas been released.
Specifications/Features:Turn to releaseUL/CSA/CEE-Stop can be locked out/includes start buttonIP55 Rated
Note: Mounts directly to motor starter enclosure
To Order:Part Number:ELECT-061 E-Stop Accessory for Motor Starter
E-Stop Accessory
3.00
2.67
3.76
2.37 2.75
3.50
2.89
2X .22 DIA.
The Remote E-Stop provides a means for locking out powerto the motor for safety. It includes an IP65 enclosure andmounting bracket to allow the E-Stop to be mounted directlyto the side of the conveyor frame.
Specifications/Features:Turn to releaseUL/CSA/CEIP65 Enclosure
To Order:Part Number:ELECT-063-WBRKT E-Stop with enclosure
Note: Includes mounting bracket to mount to conveyor frameRemote E-StopNote: It is the responsibility of the end user to properlywire motor starter and e-stops
Note: It is the responsibility of the end user to properlywire motor starter and e-stops
Note: It is the responsibility of the end user to properlywire motor starter and e-stops