250W multifunction tool original instructions & Warrantydoc.ferm.com/Servotool/documents/OTM6008...

250W multifunction tooloriginal instructions & Warranty

AFTER SALES SUPPORTUK HELPLINE NO 0905-1460005 (£ 0,06 /min.)

IRELAND HELPLINE NO 1520-932626 (E 0,15 /min.)

WEB SUPPORT www.servotool.eu

Model nuMber: PoT-250 ArT.no: oTM6008

After Sales SupportNow you have purchased a Power Craftproduct you can rest assured in theknowledge that as well as your 3 yearparts and labour warranty you havethe added peace of mind of dedicatedhelplines and web support.

OTM6008 Ma-GB-IRE 1006-15.indd 1 6/15/10 4:04:38 PM

contents

3 Introduction

4. Machine information

8. Safety instructions

11. Assembly and operation

13. Maintenance

14. Exploded view

15. Spare parts list

16. Warranty

UK Helpline 0905-1460005 • Ireland Helpline 1520-932626 Web Support: www.servotool.euModel Number: POT-250 2


introduction

congratulations on choosing to buy a Power craft product.

By doing so you now have the assurance and peace of mind that comes with purchasing a product made by one of Europe’s leading manufacturers.

All products brought to you by Power Craft are manufactured to the highest standards of performances and safety, and, as part of our philosophy for customer service and satisfaction, are backed by our comprehensive 3 Year Warranty.

We hope you will enjoy using your purchase for many years to come.

multifunction tool

The numbers in the text refer to the diagrams on pages 4.

Always read the instructions for electrical products carefully before use. It will help you understand your product better and avoid unnecessary risks. Keep this instructions manual in a safe place for future use.

Intended useThis machine is intended for dry sanding of small areas, sawing and scraping with various tool accessories, as well as for polishing, rasping, cutting and separating various materials.

Contents1. Machine data2. Safety instructions3. Assembly and operation4. Maintenance



machine information

Fig. 1

FeaturesFig. 11. On/Off switch2. Speed control3. Auxiliary handle4. Sanding sole5. Sandpaper6. Scraper7. E-cut saw blade8. Segmented HSS saw blade9. Dust adapter


1

5

6

7

4

2

3

9

8

Fig. 2


machine information


Technical specifications

Mains voltage 230-240 V~Frequency 50 HzPower input 250 WNo-load speed 15,000 - 22,000 /minWeight 1.48 kgLpA (sound pressure level) 85+3 dB(A)LwA (sound power level) 96+3 dB(A)Vibration 6.77 + 1.5 m/s2

Vibration levelThe vibration emission level stated in this instruction manual has been measured in accordance with a standardised test given in EN 60745; it may be used to compare one tool with another and as a preliminary assessment of exposure to vibration when using the tool for the applications mentioned- using the tool for different applications, or with different or poorly

maintainted accessories, may significantly increase the exposure level- the times when the tool is switched off or when it is running but not

actually doing the job, may signifi cantly reduce the exposure level

Protect yourself against the effects of vibration by maintaining the tool and its accessories, keeping your hands warm, and organizing your work patterns.

Package contents

Check the machine, loose parts and accessories for transport damage.

1 Multifunction tool1 Dust adapter1 Scraper1 Segmented HSS saw blade1 E-shaped saw blade1 Sanding sole5 Pcs sanding paper G605 Pcs sanding paper G805 Pcs sanding paper G120

5 Pcs sanding paper G1801 Auxiliary handle2 Pcs allen key1 Instruction manual1 Quick start guide1 After Sales card


Safety instructions

The following pictograms are used in these instructions for use:

Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual.

Indicates electrical shock hazard.

Contact with or inhalation of dust coming free during use (e.g. lead-painted surfaces, wood and metal) can endanger your health and the health of bystanders.Always wear appropriate protective equipment, such as a dust mask. Always use proper dust extraction during use.

Wear safety goggles. Wear hearing protection.

Warning!Read all instructions. Failure to follow all instruc tions listed below may result in electric shock, fire and/or serious injury. The term “power tool” in all of the warnings listed below refers to your mains operated (corded) power tool or battery operated (cordless) power tool. Save these instructions.

1) Work areaa. Keep work area clean and well lit. Cluttered and dark areas invite

accidents.b. Do not operate power tools in explosive atmos pheres, such as in the

presence of flam mable liquids, gasses or dust. Power tools cre ate sparks which may ignite the dust of fumes.

c. Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.

2) Electrical safetya. Power tool plugs must match the outlet. Never modify the plug in any

way. Do not use any adapter plugs which earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.

b. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of elec tric shock if your body is earthed or grounded.




machine information

c. Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.

d. Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.

e. When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use redu ces the risk of electric shock. Always use tool in con junction with a residual circuit breaker device.

3) Personal safetya. Stay alert, watch what you are doing and use common sense when

operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medi ca tion. A moment of inattention while opera ting power tools may result in serious personal injury.

b. Use safety equipment. Always wear eye protection. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries.

c. Avoid accidental starting. Ensure the switch is in the off position before plugging in. Carrying power tools with your finger on the switch or plugging in power tools that have the switch on invites accidents.

d. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.

e. Do not overreach. Keep proper footing and balance at all times. This enables better con trol of the power tool in unexpected situations.

f. Dress properly. Do not wear loose clothing or jewellery. Keep your hair, clothing and gloves away from moving parts. Loose clothes, jewel lery or long hair can be caught in moving parts.

g. If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of these devices can reduce dust related hazards.



Safety instructions

h. Use clamps or a vice to hold work. It’s safer than using your hand and it frees both hands to operate tool.

4) Power tool use and carea. Do not force the power tool. Use the correct power tool for your

application. The correct power tool will do the job better and safer at the rate for which it was designed.

b. Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.

c. Disconnect the plug from the power source before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.

d. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

e. Maintain power tools. Check for misalign ment or binding of moving parts, breakage of parts and any other condition that may affect the po wer tools operation. If dama ged, have the po wer tool repaired before use. Many acci dents are caused by poorly maintained power tools.

f. Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

g. Use the power tool, accessories and tool bits etc., in accordance with these instructions and in the manner intended for the particular type of power tool, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from intended could result in hazardous situation.

h. Damaged switches must be replaced at a cus to mer service repair centre. Do not use power tools that cannot be switched on and off.

i. Do not leave power tools unattended while they are switched on. Always switch off the tool and wait until it has come to a full standstill before leaving.

j. If the mains cable has been damaged, it must be replaced with a special mains cable. These can be obtained from the manufacturer or the manufacturer’s custo mer service department. The mains cable may only be replaced by the manufacturer, the manufacturer’s customer service department or equally qualified persons.



Safety instructions

5) Battery tool use and carea. Ensure the switch is in the off position before inserting battery pack.

Inserting the battery pack into power tools that have the switch on invites accidents.

b. Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.

c. Use power tools only with specifically desig nated battery packs. Use of any other battery packs may create a risk of injury and fire.

d. When battery pack is not in use, keep it away from other metal objects like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns of a fire.

e. Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritations or burns.

6) Servicea. Please use a qualified expert who uses original replacement parts to repair

your power tool. This will ensure proper functioning of the power tool.b. Caution! The use of any accessories or additional tools other than those

recommended in this manual may lead to an increased risk of injury. Only use original replacement parts.

Special safety instructions• Comparethemaximumnumberofrevolutionsallowedoftheaccessories

with the number of revolutions of the machine.• Whenyouputthemachineawaytheenginemustbeswitchedoffand

moving parts must have reached a standstill.• Neverattachanassemblyspannertoyourmachinewithapieceofstring

or anything similar.• Donotusesandpaperintendedforlargersandingpads.Largersandpaper

will extend beyond the sanding pad causing snagging, tearing of the paper or kick-back. Extra paper extending beyond the sanding pad can also cause serious lacerations.

• Useaclampingdeviceforsecuringtheworkpiece.• Keepyourhandsawayfromtheworkpiece.



Safety instructions

Electrical safetyWhen using electric machines always observe the safety regulations applicable in your country to reduce the risk of fire, electric shock and personal injury. Read the following safety instructions and also the enclosed safety instructions. Keep these instructions in a safe place!

Always check that the power supply corresponds to the voltage on the rating plate.

The machine is double insulated; therefore no earth wire is required.

Replacing cables or plugsIf the mains cable becomes damaged, it must be replaced with a special mains cable available from the manufacturer or the manufacturer’s customer service. Dispose of old cables or plugs immediately after replacing them with new ones. It is dangerous to connect the plug of a loose cable to a socket.



Assembly and operation

Mounting the side-handleFig. 1The side handle can be used for both left-hand and right-hand control.

• Fastenthesidehandleforleft-handoperationontheright-handsideofthe machine.

• Fastenthesidehandleforright-handoperationontheleft-handsideofthe machine.

Make sure that the side handle is fastened properly and cannot loosen unexpectedly.

Setting the speedFig.1The speed can be set (from slow to fast) using the continuous speed adjustment wheel (2).

Switching on:• Pushtheswitch(1)forwardtoposition

Switching off:• Pushtheswitch(1)backtoposition

Hints for optimum use• Clamptheworkpiece.Useaclampingdeviceforsmallworkpieces.• Drawalinetodefinethedirectioninwhichtoguidetheaccessory.• Firmlyholdthemachinebythegrip.• Switchonthemachine.• Waituntilthemachinehasreachedfullspeed.• Placetheaccessoryontheworkpiece.• Slowlymovethemachinealongthepre-drawnline,firmlypressingthe

accessory against the workpiece.• Donotapplytoomuchpressureonthemachine.Letthemachinedothe

work.• Applylesspressurewhenthemachinestartstovibrateheavily.• Switchoffthemachineandwaitforthemachinetocometoacomplete

standstill before putting the machine down.



Assembly and operation

AccessoriesFig. 1

4 + 5. Sanding sole:Sanding near edges, corners and hard to reach areas. (Depending on the sanding paper for sanding of wood, paint, varnish and stone.)6. Scraper:Scraping on solid underground. For instance removal of glue, carpets and tiles. (carpet, flooring)7. E-cut sawblade:Separating and deep plunge cuts, for sawing close to edges, in corners and hard to reach areas. (wooden materials, soft materials)8. Segmented HSS saw blade:Separating and deep plunge cuts, for sawing close to edges, in corners and hard to reach areas. (Hard and soft wood, plastic, non-ferrous metals.)

Mounting accessoriesFor saw blades, scrapers and disc cutters and cutting discs use the clamping screw in combination with the retaining ring.• RemovetheclampingscrewusinganAllenkey.• Replacethetoolandtightenitusingtheclampingscrew.Checkthatthe

tool is secure in the chuck and that the machine is correctly secured and supported.

Fitting/replacing sandpaperUsing hook and loop fastening system.• Placethesandpaperinthemiddleofthesandingdiscandpressitfirmly

with your hand.• Pressthesandpaperfirmlyontotheplatewithbrief,firmpressureand

then switch on the machine. This ensures that the disc is correctly secured and prevents excessive wear.

• Ifthesandpaperisworninaparticularspot,youcanremoveit,turnit120° and refit it or replace it.

Mounting the dust adapter.Fig. 2Mount the dustadapter using the 3 hexagonal screws as shown on figure 2. Warning! Switch the machine off and unplug the machine before mounting the accessories.



maintenance

The machines have been designed to operate over a long period of time with a minimum of maintenance. Continuous satisfactory operation depends upon proper machine care and regular cleaning.

CleaningKeep the ventilation slots of the machine clean to prevent overheating of the engine.Regularly clean the machine housing with a soft cloth, preferably after each use. Keep the ventilation slots free from dust and dirt. If the dirt does not come off use a soft cloth moistened with soapy water. Never use solvents such as petrol, alcohol, ammonia water, etc. These solvents may damage the plastic parts.

LubricationThe machine requires no additional lubrication.

FaultsShould a fault occur, e.g. after wear of a part, please contact the service address on the warranty card. In the back of this manual you find an exploded view showing the parts that can be ordered.

EnvironmentTo prevent damage during transport, the appliance is delivered in a solid packaging which consists largely of reusable material. Therefore please make use of options for recycling the packaging.

Please recycle this product at end of life. Contact your retailer or local authority recycling centre for assistance.

WarrantyThe warranty conditions can be found on the separately enclosed warranty card.



Exploded view



Spare parts list

Positon Description No. 1 + 2 Ring + screw 702809 7 Bearing 806000 16 Bearing 800608 18 Rotor 702810 19 Bearing 800607 23 Stator 702811 24 + 25 Switch cover + switch bar 702812 28 Carbon brush holder 702814 29 Carbon brush set 702814 35 Switch 702815



Warranty

WARRANTY CERTIFICATEYear of manufacture: 06/2010 250W Oscilating tool POT-250Congratulations! You have made an excellent choice with the purchase of this Quality product. Our commitment to quality also includes our service. Should you, contrary to expectations, experience defects due to material or manufacturing faults during private use within 36 months of the date of purchase we shall be liable for warranty in accordance with statutory warranty regulations, provided that: - The device was not put to any use other than the intended.- Was not overloaded. - Was not used with the wrong accessories. - Repairs where not carried out by any other than the authorised workshop. The warranty certificate is only valid in connection with the receipt. Please keep both in a safe place. The warranty does not affect your statutory rights.The product is guaranteed for a period of three years beginning on the day of purchase. Keep your purchase receipt safe as proof of the date of purchase. The guarantee period can only be extended for the duration of any repair required.During the warranty period if the item becomes defective, in the first instance, please call the helpline. We will, at our discretion either repair or exchange the device in accordance with warranty legislation.

Please include the following when sending in your product for repair:1. The receipt (proof of purchase)2. This warranty certificate with your name, address, contact details and a fault description completed overleaf.If the original receipt is not enclosed the repair will be charged for in all cases. After the warranty has expired you can still send defective devices for repairs to the address at the end of this booklet. Quotes as well as repairs after warranty period are to be paid for in all cases. Ensure the product is sent well packed as no responsibility can be accepted for items lost or damaged in transit. This warranty does not affect your statutory rights.

EC DECLARATION OF CONFORMITYWe Ferm B.V.Lingenstraat 6, 8028 PM Zwolle, The Netherlandsdeclare that the design and construction of the following machine, in the form supplied by us, comply with the requirements of the appropriate EC directives.Product Description: Multifunction toolModel: POT-250Appropriate EC directives: 2006/42/EC, 2004/108/EC, 2002/95/EC, 2002/96/EC, 2006/95/ECApplicable harmonised norms: EN 60745-1, EN 60745-2-4, EN 55014-1, EN 55014-2, EN 61000-3-2, EN 61000-3-3

J.A. Bakker - van Ingen CEO Ferm B.V. 06/2010


In order to deal with your enquiry as quickly and efficiently as possible, we ask you to send your enquiry by email ([email protected]). Do not forget to include your name, address and a

daytime telephone number.

Alternatively, you can contact our service hot-line on the number given below.Office hours are as follows:

Mon - Fri: 8 am - 6 pm, Sat: 10 am - 2 pm, Sun: 10 am - 4 pm

UK Helpline

Circuit Tech Ltd.Units 1/9 Stanley Mill • Kirkebrok Road • Deane, Bolton Lancs, England • BL3 4JE

Service Center0905-1460005 - £ 0,06 /min.*

Ireland Helpline

Circuit Tech Ltd.Units 1/9 Stanley Mill • Kirkebrok Road • Deane, Bolton Lancs, England • BL3 4JE

Service Center1520-932626 - E 0,15 /min.*

WEB SUPPORTwww.servotool.eu

Replacements or repairs under guarantee regulations are free of charge.

* Applies to calls from BT/Eircom landlines. Charges by other network providers and calls from mobiles may vary. Prices correct at time of print.

250W multifunction toolPOT-250

Name:

Address:

Contact Telephone No.:

Fault Description:

Please complete this section before sending in your warranty certificate.

If you are requested by the manufacturer to return the item for repair please complete the enclosed section and send it together

with your product and your receipt (proof of purchase) to theservice address shown below.

1006-15


Date post:	27-Jan-2021
Category:	Documents
Upload:	others
View:	2 times
Download:	0 times

250W multifunction tool original instructions & Warrantydoc.ferm.com/Servotool/documents/OTM6008...

Documents