Date post: | 20-Oct-2015 |
Category: |
Documents |
Upload: | pieroaless |
View: | 94 times |
Download: | 1 times |
3Dynatel™
Qualification Test Set 950ADSL2 Plus
Rugged and portable for ADSL2+ testing and measurement.
3m™ dynatel™ qualification test set 950adsl2 plus
The heat is on to provide high-speed Internet access and enhanced broadband services over existing copper networks. 3M’s next generation Dynatel™ Qualification Test Set 950ADSL2 Plus has all the right features to ensure the successful installation and maintenance of ADSL2+ service. The 3M™ Dynatel™ Qualification Test Set 950ADSL2 Plus is a cost-
effective solution ideal for technicians providing both POTS testing
and verification of ADSL2+ modem connectivity.
rugged, reliaBle design
The Dynatel test sets are housed in a light-weight, hand-held case
designed for ease-of-handling and portability. Each unit weighs less
than 2.5 pounds with the rechargeable battery pack included. The
display clearly provides test results and measurements including bin
graphs and data rates.
Test set in soft carry case.
The right tool for the job.
2
Back/Undo
Speaker Volume Dialing
Resistance Measurement
Voltage Measurement
Tool Box
Opens Length
Contrast Down
PowerON/OFF
Backlight ON/OFF
Auto Test / Menu Down
AC Tests / Menu Up
Send Tone
ADSL Connection Test Save Results
Ping Test
Loop Current
Select or Change Setup
Keypad functions
Contrast Up
Choose Option or Measurement Mode
sample screen
3m™ dynatel™ qualification test set 950adsl2 plus
3
4
pots and adsl tests
The Dynatel Qualification Test Set 950ADSL2 Plus conducts multiple metallic tests independently
or as part of the Autotest function. Tests include CO and foreign voltage, insulation and loop
resistance, longitudinal balance and loss & noise. Autotest results can be saved and uploaded
for record storage and later analysis. The tester can also generate tones up to 2.2MHz for loss
measurements.
ADSL2+ active testing include performance measurements including data rate up/down, max
rate, attenuation etc., as well as error measurements such as FEC, CRC and HEC with bin
graph capture to analyze data transfer performance. The 950ADSL2 Plus can also ping to an
ISP to measure response time. In addition, ADSL2+ test results can be saved and uploaded for
record storage or later analysis.
product featuresTESTS PERFORMED
Volts – AC and DC
Loop Current
Resistance Test
Soak Test
Ground Resistance
Opens
Loss and Noise
Longitudinal Balance
Pulse and DTMF Dialing
Load Coils
POTS Autotest
Precision Tones to 2.2Mhz
ADSL2+/ADSL2/ADSL Connectivity
Ping Testing
FEATURES
Backlit LCD
Water resistant attachment for test leads and DC charger
Rechargeable NiMH battery
Serial upload to PC
Storage for 100 ADSL2+ results
Storage for 10 POTS results
3m™ dynatel™ qualification test set 950adsl2 plus
5
general specificationsSize 60 mm high x 100 mm wide x 200 mm long
Weight Less than 1.5 lb. with battery
Battery Ni-MH: 2100 mAhr – shrink wrap pack, user replaceable through access door on bottom of unit
Battery life 8 hours standby (backlight off) + 20 full ADSL2+ qualification tests of 2 minute durationSeparate charger / AC/DC adapter connects to the unit through external power jackAuto shutoff after 5 minutes with no activity, except during charging
Display 64 x 128 pixel, 57 mm x 31 mm viewing area with LED backlight
Test leads Red, black and green leads. 1.5 meters long. Connected to unit via standard jacks.
Breakdown voltage 360 VDC, 250 VAC
Operating temperature -18°C to 60°C except for ADSL2+ and Battery Charger Functions0°C to 60°C ADSL Functions0°C to 50°C battery charger operation
Humidity 0 to 95% non-condensing
Shock Will survive 3 drops from 1 meter
Regulatory CE/FCC per: CISPR 11:2003 / EN55011:2003, Class A, Group 1FCC CFR 47, Part 15, Subpart B – Class AEN61326:1997+A1:1998+A2:2001 ( IEC 61326:2002 )
Dialing DTMF or Pulse Dialing – 10 number storage
ADSL2+ Test Storage 100 sets of results, each identified with an alpha numeric labelStored results can be viewed in the test set
POTS test storage 10 sets of results, each identified with a 10-digit numeric identifier Stored results can be viewed in the test set.
POTS autotest Autotest will run the following tests: V (T,R,Gnd), mA, Ground Resistance, Ohms (T,R,Gnd), Opens (T,R,Gnd), Load Coil Count, Noise, PI, LB and Loss (up to 10 voiceband frequencies)
Languages English, French or alternative 2nd language subject to availability
Serial port Adapter cable connected to the test leads can be used for connecting the unit to a PCThe serial connection supports the following:• Upload of test results to the PC• Remote configuration of ADSL and Ping parameters from a PC• Field software updates
3m™ dynatel™ qualification test set 950adsl2 plus
6
pots measurement specificationsFUNCTION RANGE RESOLUTION ACCURACY TEST LEADS
AC voltage 0 to 250 VAC (input resistance = 1M Ohm ± 5% )
± 1 V ± 2% R-T, R-G, T-G
DC voltage 0 to 250 VDC (input resistance = 1M Ohm ± 5% )
± 1 V ± 2% R-T, R-G, T-G
Loop Current (DC) 0 to ±110 mA 1 mA ±2mA R-T (Impedence= 430Ω)
Resistance 0 ohm to 999 ohms 1K ohm to 9.9K10K ohms to 99.9K ohms100K ohms to 999K ohms1M ohm to 9.9M ohms10M ohms to 30M ohms
1 ohm ohms 10 ohms100 ohm1K ohm100K ohms1M ohm
± 5 ohm ± 3% ± 3%± 3%± 3%± 3%± 10%
R-T, R-G, T-G
Voltage compensation for foreign voltage conditions
Loop loss -50 to +10 dBm 200 to 5000 Hz
1 dB ±1 dB R-T (Impendence = 600Ω)
Frequency during loss, single frequency only and levels greater than -45 dBm
200 to 5,000 Hz 1 Hz ± 3 Hz ± 0.2% R-T
Noise metallic with C-message weighting**
0 to 60 dBrnc 1 dB ±2 dB R-T (Impedence = 600Ω)
Noise to ground with C-message weighting**
40 to 100 dBrnc 1 dB ±2 dB R & T-G (Zin=100KW)
Note: Available only with a C-Message filter, for Psophometric version contact Communication Markets Division, 3M Telecommunications.
Opens 0 to 9,999 ft. 10,000 to 99,999 ft(0 to 9,999 m)(10,000 to 30,000m)
1 ft. 100ft(1 m)(100m)
± 20 ft. ±5% +/- 5%(± 6m, ±5%)(+/- 5%)
Ring, Tip, Mutual
Longitudinal balance 0 to 65 dB 1 dB ±2 dB T,R-G
Ground resistance 0 to 50 Ω 1 Ω ± 3 Ω
Load coils Count 0,1,2,3,4 or >4 coils +/- 1 coil
Note: First load must be >3000’ from unit and 3000’ of cable must extend beyond the last load coil for an accurate count.
Precision tone Frequency: 404, 1004, 2804 (preset) (Source impedence = 600 ohms +/- 5% )
Amplitude 0 ± 0.5 dBm R-T
Frequency: 8000 Hz – 2.2Mhz (user settable) +/- 10% Source impedence = 100 ohms +/- 5% 577 Hz intermittent trace tone
Amplitude 0 ± 0.5 dBm
Amplitude 5V P-P
R-T
Notes: * Percent of reading ** C-message specification has additional frequency dependent tolerance. Refer to “Subscriber Loop Transmission Test Set Specification”, Bell System PUB 55020, January 1982.
3m™ dynatel™ qualification test set 950adsl2 plus
3m™ dynatel™ qualification test set 950adsl2 plus
adsl/adsl2+ measurement specificationsADSL/ADSL2+ Standards T1.413 i2 (ANSI)
G.992.2 (G.LITE)G.992.1 (G.DMT)G.992.3 (G.DMT.bis/ADSL2)G.992.5 (ADSL2plus)Support for Annexes A, B, and LLine impedance 100 ohms nominal
FUNCTION MEASUREMENT
ADSL2+ Status (up/down) Fast rate Interleaved rateMaximum attainable bit ratePowerMarginAttenuationCapacity
ADSL2+ Information (up/down) FEC (forward error correction count)CRC Error countHEC ATM Header Errors countSEF Severe Errors Frame countLOS Loss of signal count
Bin Graph
ADSL2+ Alarms LOS: Loss of Signal > 127LOF: SEF > 127LCD: NCD or LCD > 127
pots and adsl testsPing capability is supported via an internal communication protocol as listed.
IP address assignment DHCP per RFC 2131
IPCP per RFC 1332
Point-to-Point Protocol PPP over ATM (PPPoA)
PPP over Ethernet (PPPoE)
Authentication PAP
CHAP
Ping Connection time +/- 10 mS
7
3Communication Markets Division 3M Telecommunications6801 River Place Blvd.Austin, TX 78726-9000800/426 8688Fax 800/626 0329www.3MTelecommunications.com
Litho in USA.80-6113-1560-9© 3M 2006. All Rights Reserved.Please Recycle
3M and Dynatel are trademarks of 3M.
product contents and ordering information3M PART NO. DESCRIPTION UPC
950ADSL2-PLUS-SN 950ADSL2 Plus ADSL2+ test set with single nail leads CE100710744
950ADSL2-PLUS-BON 950ADSL2 Plus ADSL2+ test set with bed-of-nails leads CE100710751
950ADSL2PLUS 950E-ADSL2 Plus test set with bed-of-nails leads-psophometric (European)
CE100712385
1188* 1188 cigarette lighter adapter for 965AMS/950ADSL2 Plus 80611316227
950-NIMH NIMH battery pack, 949ADSL/950ADSL/950ADSL2 PLUS CE100700745
950ADSL2PLUS-ADAP 950ADSL2 Plus, 12VDC charger CE100707260
950ADSL2PLUS-CABLE 950ADSL2 Plus, serial cable CE100707252
1143 1143 lead, test green 965DSP/950ADSL2 Plus 80610864375
1144 1144 lead, test black/red 965DSP/950ADSL2 Plus 80610864359
950-CASE Soft carrying case 949/950 CE100700737
*optional accessory
To order, call 800/426 8688. For more information, please contact your local 3M representative.
3m™ dynatel™ qualification test set 950adsl2 plus
Important NoticeAll statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability. This product will be free from defects in material and manufacture for a period of 12 months from the time of purchase. 3M MAKES NO OTHER WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except where prohibited by law, 3M will not be liable for any loss or damage arising from this 3M product, whether indirect, special, incidental or consequential regardless of the legal theory asserted.