WARNING:Small parts.
Not for children under 3 years.CHOKING HAZARD -
!
CAUTION:Adult assembly required.!
Melissa & Doug, LLC
All Rights Reserved
www.MelissaAndDoug.comWe care about your comments.Please call us! 1-800-284-3948
Victorian Dollhouse
Assembly Instructions
ITEM #2580 B
Parts List
Page 2 of 36
1E
Foundation Panel 1D
Foundation Panel 1E
1H
Foundation Panel 1H
1B
Foundation Components
Foundation Panel 1B
1F
Foundation Panel 1F
1G
Foundation Panel 1G
1C
Foundation Panel 1C
1D
1A
Front Steps 1A
Page 3 of 36
2
Floor Panel 2 (1st floor)
Floor Panels(upper surface views)
11
Floor Panel 11 (2nd floor)
14
Floor Panel 14 (top floor)
Page 4 of 36
4
Wall Panel 4
Outer Wall Panels(exterior views)
5
Wall Panel 5
7
Wall Panel 7
8
Wall Panel 8
10
Wall Panel 10
6
Wall Panel 6
9
Wall Panel 9
15
Wall Panel 15
Page 5 of 36
3
Wall Panel 3
13
Wall Panel 13
12
Staircase Assembly 12(1st floor)
16
Staircase Assembly 16(2nd floor)
28
Screw
2929
screw hole plug and cover
Inner Wall Panels, Staircases and Assembly Hardware
Page 6 of 36
Roof Panel 23
23
Roof Panel 25
25
Roof Panel 24
24
Roof Panel 22
22
Roof Panel 18
18
Roof Panel 17
17
Roof Panel 27
27
Roof Panel 26
26
19
Roof Panel 19
Roof Panel 20
20
Roof Panel 21
21
Roof Panels(exterior tiled surface views)
Page 7 of 36
22 21 2026
27
18192524
top view
23
front view
5
10
8
15
right view
79
1G1D
14
11
2
13
12
16
3
rear view1H
isometric front left view
1A1C1E1F 1B
Completed dollhouse views(with component item numbers)
Page 8 of 36
Step 1: Begin by attaching Front Steps 1A to the painted surface of Foundation Panel 1B using 2 screws (item 28), as illustrated. Next, with artwork facing out on all the foundation panels, assemble the foundation as shown in the diagram. Make sure that the screw holes on the long edges of panels 1E and 1H are facing up. Secure the panels together with 16 screws (item 28).
1G
1C
1B
1A1D
1E
1F
screw holesfacing up
28
screw holesfacing up
Page 9 of 36
3
2
28
yellow and green tile artwork on thisend of Floor Panel 2
yellow tile artwork on bottomhalf of Wall Panel 3
pink with purple tile wall artwork onupper half of Wall Panel 3
wood floor artwork on this end of Floor Panel 2
Step 2: Attach Wall Panel 3 to Floor Panel 2 with 2 screws (item 28) inserted through the bottom of Floor Panel 2. Make sure to orient the artwork on the wall and floor panels as described below.
Page 10 of 36
Step 3: Attach the floor panel assembly from Step 2 to the foundation assembly from Step 1 using 5 screws (item 28), as illustrated.
28
Step 2 assembly
Step 1 assembly
Page 11 of 36
28
Step 4: Attach Wall Panel 4 to Floor Panel 2 with 2 screws (item 28), as illustrated, making sure the window ornamentation is facing out.
4
2
Page 12 of 36
5
28
Step 5: Attach Wall Panel 5 to Wall Panel 4 and Floor Panel 2 with 3 screws (item 28), as illustrated, making sure the window ornamentation is facing out.
42
Page 13 of 36
6
Step 6: With the pink clapboard artwork facing out, slide Wall Panel 6 into position and secure with 2 screws (item 28), as illustrated. Make sure that interior wall artwork on panels 5 and 6 are aligned after assembly.
528
Page 14 of 36
7
28
Step 7: Attach Wall Panel 7 to Floor Panel 2 with 2 screws (item 28), as illustrated, making sure the window ornamentation is facing out.
2
Page 15 of 36
8
28
Step 8: Attach Wall Panel 8 to Wall Panel 7 and Floor Panel 2 with 3 screws (item 28), as illustrated.
7
2
Page 16 of 36
9
28
Step 9: With the pink clapboard artwork facing out, slide Wall Panel 9 into position and secure with 2 screws (item 28) to Wall Panel 8, as illustrated. Make sure that the interior wall artwork on panels 9 and 6 (from Step 6) are identical.
8
6
Page 17 of 36
10
28
Step 10: Place the bottom edge of Wall Panel 10 into the slot behind the front steps. Then attach to Floor Panel 2, Wall Panel 6 and Wall Panel 9 with 6 screws (item 28), as illustrated. The window and door ornamentation should be facing out, and the exterior and interior wall artwork on wall panels 10, 6 and 9 should be aligned.
6
9
2
Page 18 of 36
11
28
Floor Panel 11 slot
Step 11: Position Floor Panel 11 as shown below. Next, fit the slot in Floor Panel 11 over the inner Wall Panel 3, and carefully slide it down until the holes on its edges align with the 8 holes in the surrounding Wall Panels 7, 8, 10, 5 and 4. Secure Floor Panel 11 to the surrounding wall panels with 8 screws (item 28), as illustrated in the top view diagram.
back view of dollhouse
3
11
28
top view of dollhouseshowing all 8 screws
7
8
10
5
4
Page 19 of 36
12
28
opening in Floor Panel 11
3
11
2
bottom edge
top landing
Step 12: Attach Staircase Assembly 12 by sliding it down through the opening in Floor Panel 11, as illustrated. Place the staircase flat against Wall Panel 3, with the top landing of the staircase resting on Floor Panel 11 (2nd floor panel) and the bottom edge resting on Floor Panel 2. Secure with 1 screw (item 28) inserted through the opposite side of Wall Panel 3.
Page 20 of 36
13
28
Step 13: With the striped wallpaper artwork facing right, align Wall Panel 13 with the two remaining holes in Floor Panel 11 and secure with 2 screws (item 28) inserted from underneath the floor panel, as illustrated. The interior wall artwork on panels 13, 10, 5 and 4 should be aligned.
105
4
pink striped wallpaper artwork
11
Page 21 of 36
artwork surface
15
14
28
Step 14: Make sure that the artwork surface of Floor Panel 14 is facing up and the window ornamentation on Wall Panel 15 is facing out, then secure these panels together with 3 screws (item 28) inserted from underneath Floor Panel 14, as illustrated.
angled edge
Page 22 of 36
28Step 14 assembly
Step 15: Attach the floor assembly just completed in Step 14 to the main dollhouse assembly by aligning the 4 holes in the floor with the 4 holes on inner Wall Panels 3 and 13. The 2 holes on the edge of Floor Panel 14 should also be aligned with the holes on Wall Panel 7, as illustrated. Secure with 6 screws (item 28).
28
3
13
7
14
Page 23 of 36
16
28
Step 16: Attach Staircase Assembly 16 by sliding it down through the opening in Floor Panel 14, as illustrated. Place the staircase flat against Wall Panel 3, with the top landing of the staircase resting on Floor Panel 14, and the bottom edge resting on Floor Panel 11. Secure with 1 screw (item 28) inserted through the opposite side of the Wall Panel 3.
14
3
11
Page 24 of 36
17
28
notch
17
10
8
Step 17: Attach Roof Panel 17 by sliding the notch around the intersecting Wall Panel 8. Then align the hole in Roof Panel 17 with the hole in the top edge of the Wall Panel 10 and secure with 1 screw (item 28), as illustrated.
Page 25 of 36
Step 18: Attach Roof Panel 18 by aligning its hole with the hole in the top edge of the Wall Panel 8, as illustrated. Secure with 1 screw (item 28).
18
28
18
8
Page 26 of 36
19
28
15
Step 19: Attach Roof Panel 19 with 1 screw (item 28) inserted from the interior side of Wall Panel 15, as illustrated.
Page 27 of 36
20
28
7
15
8
Step 20: Place Roof Panel 20 onto Wall Panels 15, 8 and 7. Secure with 4 screws (item 28), as illustrated.
Page 28 of 36
21
28
20
15
17
10
Step 21: Place Roof Panel 21 onto Wall Panels 10 and 15, and against Roof Panels 20 and 17. Secure with 6 screws (item 28), as illustrated.
Page 29 of 36
2228
slot
Step 22: Attach Roof Panel 22 by pressing the slot on its underside firmly over the top edge of Wall Panel 4, as illustrated. Secure with 1 screw (item 28).
4
Page 30 of 36
Step 23: Attach Roof Panel 23 by placing its underside slot firmly on the top edge of Wall Panel 4, as illustrated. Secure with 3 screws (item 28).
28 23
4
Page 31 of 36
Step 24: Attach Roof Panel 25 by placing its underside slot firmly on the top edge of Wall Panel 5, as illustrated. Secure with 1 screw (item 28).
2528
roof panel underside slot
5
Page 32 of 36
Step 25: Attach Roof Panel 24 by placing its underside slot firmly on the top edge of Wall Panel 5, as illustrated. Secure with 3 screws (item 28).
24
28
5
Page 33 of 36
Step 26: Attach Roof Panel 26 to the top edge of the Wall Panel 7, as illustrated. Secure with 1 screw (item 28).
26
28
7
Page 34 of 36
Step 27: Attach Roof Panel 27 by placing it on the top edge of the Wall Panel 7, as illustrated. Secure with 3 screws (item 28).
27 28
7
Page 35 of 36
external hole plugs
external hole plugs
trimmed internal hole cover
internal hole covers
OPTIONAL. PLEASE NOTE - proceeding with Step 28 will prevent the dollhouse from being disassembled without damage.
Step 28: For a dollhouse with a more aesthetic appearance, matching hole plugs and covers have been included to conceal both external and internal screw holes. For external holes (roof panels and exterior walls), select the proper color plug and apply a small amount of wood glue to one end, then insert a plug into each screw hole. For internal holes, select a cover with the matching paper artwork, trim if necessary, and apply with wood glue over the interior screw hole. Allow sufficient drying time before play time use.
Page 36 of 36