25843 Jefferson Avenue Murrieta, CA 92562 • Phone: 951.526.2239 Fax: 951.526.2441 www.srsengineering.com • www.srsbiodiesel.com

The DWC-Series - Drum Washer / Crusher Unit

SRS Engineering's drum washing and crushing system (DWC-Series) is designed for applications that require washing of the drums prior to crushing the drums for disposal. Instead of a separate drum washer and a separate compactor, the DWC accomplishes both the jobs in one unit - thus saving time and money.

SRS' Drum Washing/Crushing systems (DWC-Series) are custom designed to suit the customer's unique application and requirements and can be developed for aqueous, caustic, and solvent applications. The Drum washer/crusher unit can also accommodate triple-rinse and other such EPA handling and disposal requirements.

25843 Jefferson Avenue Murrieta, CA 92562 • Phone: 951.526.2239 Fax: 951.526.2441 www.srsengineering.com • www.srsbiodiesel.com

DWC-Series Standard Features:

• High pressure washes inside surfaces of open and bung top 30 and 55 gallon drums (Optional Exterior Wash)

• Designed for water, caustic, or solvent wash applications • Heavy-duty Unibody welded construction • Galvanized steel internal piping (Optional Stainless Steel) • View window for washer / compaction chamber • Rotating wash nozzle with high impingement spray nozzle and assembly • Moving wash assembly for drum interior surface washing • Adjustable high pressure wash to 12 GPM and 250 P.S.I (standard 5 GPM) • Electric wash pump • Electric rinse pump (Optional) • Pneumatic (double diaphragm) return / scavenger pump • Internal gradient liquid reservoir with sensor • 90,000 Lbs RAM force (for maximum compaction for maximum storage capabilities) • Pressure monitoring system • 4" duct for ventilation ( to be tied into customer ventilation system) • Drum piercing system with heavy duty tear-through design for laborious use which creates

internal-only sharp-edged pieces of drum and creates a much safer stacking of crushed drums.

• Lower section drain piercing mechanism for added drainage (internal tear only) • Programmable Logic Controller (PLC) in NEMA 4X enclosure • Operator terminal with color touch screen display for fully adjustable controls with

password protection and cycle counter for system monitoring • Safety switch with automatic shut down for fault conditions • Solid hydraulic cylinder 4" shaft with 7" cylinder • Heavy-duty cylinder guide sleeves for dependability of cylinder for rigorous uses • 15 Horsepower motor • Programmable delay for system shut-down (helps maintain cooler oil Temp) • Hydraulic oil radiator (for longer operation) • 480 3 Phase/ 60Hz or other • Pre wired with single point connections for field installation • Maintenance, Training manual, and itemized parts list • Drawings and manufacturer inserts provided • One year Limited Warranty

25843 Jefferson Avenue Murrieta, CA 92562 • Phone: 951.526.2239 Fax: 951.526.2441 www.srsengineering.com • www.srsbiodiesel.com

Conveyorized unit:

The conveyorized option is an inline automatic feed drum washing/crushing system which indexes the drums into position.

1. A platen secures the drum while a hydraulic punch penetrates the top and the bottom of the drum simultaneously.

2. The punches withdraw and the wash head is inserted. 3. The wash cycle is then performed after which the head

withdraws and the platen completes the down stroke crushing the drum.

4. The drum is then ejected to a discharge conveyor which completes the entire process cycle.

Conveyorized Unit Features:

• Compaction chamber staging system (3) drum capacity staging conveyor (For automatic operation)

• Rail lift guide with loader and locking mechanism (Reduces lift factor of drums) • Internal container rolling guide platform for consistent compaction and alignment • Automatic drum ejection system for drum placement to (bin or conveyor provided by

customer) 10"L X 5"W X 7"H (Note: Width has input chute (6') and output (2') chute)

DWC-Series Principle of Operation:

1. Remove the bung tops or drum covers.

2. Place the drums on the gravity roller conveyor (bung hole down). This allows any liquids to drip into a drip tray located under the conveyor, which flows into the sump.

3. The drums are released as required and moved to position #1, where a linear actuator pushes them onto a dolly track into Position #2, one at a time.

4. In position #2, a hydraulically operated auto punch punctures a hole in the bottom of the drum (this is done from the top, as the drum is inverted). This hole is always at the same position at the center of the drum.

5. The drum is indexed to position #3 on the dolly track, where a spray head is lowered into the drum through the punched hole, and an automatic wash operation is performed. The wash is performed by a high volume, high pressure spray from rotating wash heads (up to 20GPM @ up to 150 psi). The dirty wash water is released

25843 Jefferson Avenue Murrieta, CA 92562 • Phone: 951.526.2239 Fax: 951.526.2441 www.srsengineering.com • www.srsbiodiesel.com

through the bung hole at the bottom, and recirculated to the sump and an external tank. Heated water can be used as an option, if desired.

6. After the wash, the dolly moves the drum to the crushing area, where it is crushed with a 60,000 pound compactor in position #4. This reduces the drum to a height of 3-4 inches (depending on the steel gauge of the drum).

7. The crushed drum is then dropped into a bin, or onto another conveyor, as desired.

Note: The only labor involved is the removal of the bung top and placement of the drum upside down on the gravity conveyor. The rest is automatic and requires no manual operation.

This system is constructed of carbon steel (Optional Stainless Steel) and comes completely assembled and pre-tested ready to be installed in place.

Washing Operations

High pressure pumps are used to spray a wash solution to remove the most difficult residues. An advanced microprocessor control (PLC) unit verifies all safety parameters before initiating the pre-programmed cycles or sequences which can include but are not limited to wash, rinse(s), sanitize, purge, exhaust, and drying cycles. While the system is in operation the main control panel has an (HMI) which displays current system status.

The HMI displays:

• Present Cycle • Time/Date Stamp • Operator Fault Conditions • Part Count • Life Cycle of System • Components Scheduled Maintenance Tasks • Tag Alarms with Part Numbers • Amount of Down Time Incurred

The wash systems are fully capable of displaying other information including desired customer information, tank temperature/levels, and other auxiliary equipment information pertinent to the functionality of the system.

25843 Jefferson Avenue Murrieta, CA 92562 • Phone: 951.526.2239 Fax: 951.526.2441 www.srsengineering.com • www.srsbiodiesel.com

Operating Control Systems

SRS' automatic systems are equipped with a Programmable Logic Controller (PLC). The user interface prompts the operator through comprehensive menus to set up the operating system functions. This enables the PLC to operate the system automatically while providing displayed current status information.

The PLC monitors system and auxilary equipment sensors, flow rates, temperatures, fault conditions, and contacts to verify proper grounding, before initiating the start function.

Fault conditions are diagnosed and clearly displayed on the HMI, to ensure operator safety and ease of operation. The unit will systematically shut down in a fail safe mode in the event of a fault condition or at the end of the cycle.

DCS PLC HMI ABB Bailey INFI 90 ABB Fischer & Porter DCI Allen-Bradley ProcessLogix Delta V Fisher-Rosemount RS3 Honeywell TDC/TPS Systems Honeywell Plantscape Honeywell Experion Siemens Simantic PCS Siemens Moore APACS

Allen-Bradley SLC Allen-Bradley PLC5 Allen-Bradley ControlLogix Allen-Bradley MicroLogix General Electric 90/70 Koyo DirectLogic Modicon Quantum Modicon 884/984 Siemens APT Siemens S7 Mitsubishi

Allen-Bradley - PanelView Rockwell - RSView, RSBatch Siemens - WinCC, OSx Wonderware - InTouch, InTrack, InControl, InBatch, InSQL