Home >Documents >2.92mm (SMK) Series Adapters & Connectors€¦ · End Launch Plug - Screw-On Type ˜ ˜ ˜ ˜˜ ˜...

2.92mm (SMK) Series Adapters & Connectors€¦ · End Launch Plug - Screw-On Type ˜ ˜ ˜ ˜˜ ˜...

Date post:28-Jul-2020
Category:
View:0 times
Download:0 times
Share this document with a friend
Transcript:
  • 2.92mm (SMK) Series Adapters & Connectors

    Catalog

    belfuse.com/cinch

  • Index

    Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-5

    Connectors

    End Launch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 2 Hole Flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 4 Hole Flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Field Replaceable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Other . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

    Adapters Same Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Between Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10-12

    Assembly Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13

    Tooling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

    Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15

    belfuse.com/cinch

  • 50 Ohm Connectors - Inches (Millimeters) - Customer Drawings Available Upon Request4

    2.92mm Series

    The Johnson™ 2.92mm Series Connector provides an excellent solution for demanding applications requiring high frequency transmission. Although similar to the SMA interface, a smaller internal body diameter (2.92mm) and air dielectric provide a higher cutoff frequency and other key advantages:

    Bodies: Stainless steel/passivated per QQ-8-626, gold plated per MIL-G-45204 .00005" min. or stainless steel/passivated per MIL-F-14072 B (EL) 300

    Contacts: Female - beryllium copper per QQ-C-530, gold plated per MIL-G-45204 .00005" min.

    Contact Support Beads: PTFE fluorocarbon per ASTM D 1710 and ASTM D 1457 or modified PPE resin

    Seal Rings: Silicone rubber per ZZ-R-765

    *All gold plated parts include a .00005” min. nickel underplate barrier layer.

    MATERIAL SPECIFICATIONS

    � Precision manufacturing allows superior electrical performance to 40 GHz.

    � Female contacts have a unique three-slot construction, which enhances connectivity by creating a more rugged connector while reducing the chance of intermittent connections.

    � Precise assembly tooling assures excellent, repeatable contact and support bead location on cabled connectors.

    � Connector mating interface per MIL-STD-348.

    � Mating interface control provides consistent electrical performance.

    � The plug connector VSWR is 1.20 Max to 40 GHz and a 12 inch 2.92mm plug to plug cable assembly performs better than 1.35 VSWR to 40 GHz.

    � The Field Replaceable Jacks are teamed with a high quality hermetic seal feed thru for use in sealed circuit modules.

    � The 2.92mm plug interface employs more precise dimensions than an SMA and uses a shorter snub nose male pin such that the connector bodies align before lhe contacts engage.

    MATING ENGAGEMENT:

    2.92MM SERIES PER MIL-STD-348

    Engagement Design: MIL-STD-348, Series 2.92mm

    Engagement/Disengagement Force: 2 inch-pounds maximum

    Mating Torque: 7 to 10 inch-pounds

    Coupling Proof Torque: 15 inch-pounds minimum

    Coupling Nut Retention: 60 pounds minimum

    Contact Retention: 6 pounds minimum axial force (captivated contacts)

    Cable Retention:

    .086 semi-rigid 30 16

    .141 semi-rigid 60 55

    Notes:1. ID of contact shall meet VSWR and connectivity requirements when mated with dia. .0355-.0365 male pin.

    Axial Force (lbs) Torque (in-oz)

    MECHANICAL SPECIFICATIONS

    (Meets or exceeds the applicable paragraph of MIL-C-39012)

    Temperature Range: -65°C to + 165°C

    Thermal Shock: MIL-STD-202, Method 107, Condition B

    Corrosion: MIL-STD-202, Method 101, Condition B

    Shock: MIL-STD-202, Method 213, Condition I

    Vibration: MIL-STD-202, Method 204, Condition D

    Moisture Resistance: MIL-STD-202, Method 106

    ENVIRONMENTAL RATINGS

  • 550 Ohm Connectors - Inches (Millimeters) - Customer Drawings Available Upon Request

    2.92mm Series

    Impedance: 50 ohms

    Frequency Range: 0-40 GHz

    VSWR: {f = GHz)

    Semi-rigid straight cabled connectors and adapters 120 Max

    Field replaceable (see typical return loss graph) N/A

    Working Voltage: (Vrms maximum)

    Connectors for Cable Type

    .086 semi-rigid and field replaceable 335 85

    .141 semi-rigid and adapters 500 125

    Dielectric Withstanding Voltage: (VRMS minimum at sea level)

    .086 semi-rigid and field replaceable 1000

    .141 semi-rigid and adapters 1500

    Corona Level: (Volts minimum al 70,000 feet)

    .086 semi-rigid.and field replaceable 250

    .141 semi-rigid and adapters 375

    Insertion Loss: (dB maximum)

    Adapters 0.06 f (GHz), tested at 6 GHz

    Straight semi-rigid cable connectors 0.03 f (GHz), tested at 10 GHz

    Insulation Resistance: 5000 megohms minimum

    Contact Resistance: (milliohms maximum)

    Center contact straight cabled connectors 3.0* 4.0

    Center contact adapters 4.0 6.0

    Field replaceable connectors 6.0 8.0

    Outer contact (all connectors) 2.0 N/A

    Body to cable (gold plated connectors) 0.5 N/A

    Body to cable (stainless steel/passivated connectors) 5.0 N/A

    RF Leakage: (dB minimum, tested at 2.5 GHz) -90dB

    RF High Potential Withstanding Voltage: (Vrms minimum, tested at 4 and 7 MHz)

    .086 semi-rigid and field replaceable 670

    .141 semi-rigid and adapters 1000

    ELECTRICAL RATINGS FIELD REPLACEABLE APPLICATION NOTES

    Field Replaceable Test AssemblyTypical Return Loss

    The field replaceable connectors manufactured by JohnsonTM, are easy to install and replace. The hermetic seal is mounted into the circuit module wall and the connector can be removed and replaced without destroying the hermeticity of the circuit housing.

    The field replaceable connector creates a transition from microstrip circuitry to a coaxial transmission line. The 2.92mm seal pin diameter is .012 (.030) to minimize the capacitive effects on the circuit trace. For optimum electrical performance, ihe transition from the hermetic seal to the microstrip trace must be properly compensated. Compensation involves adjusting the microstrip trace width to minimize any Impedance discontinuities found in the transition area.

    The plot shown below is representative of the typical return loss of a JohnsonTM field replaceable 2.92mm connector. To produce the data shown below, a test fixture is created using the JohnsonTM 2.92mm hermetic seal. The fixture consists of a suitably thick spacer plate with the hermetic seal mounted flush to both surfaces. Two connectors are mounted back to back around the fixture and the VSWR of this lest assembly is measured. The calculated return loss trace shown Is equivalent to the square root of the measured VSWR of the test assembly. Since the connectors tested are of identical design. it can be stated with fair accuracy that the calculated data shown represents the response of a single field replaceable connector and its transition to the hermetic seal.

    Although JohnsonTM does not publish a VSWR specification for field replaceable connectors, typical connector return loss can be expected to be less than -20 dB through 40 GHz. A VSWR specification is not stated because an Industry standard method for testing field replaceable connectors does not exist. The actual performance of the connector is dependent upon the following:

    1. For optimum electrical performance, JohnsonTM recommends the use of our standard 142-1000-033 hermetic seal with a pin diameter of .0120 (0.305) +/ - .0005 (0.013).

    2. It is recommended that the hermetic seal be mounted flush with the circuit housing. Tolerance variations between the hermetic seal and machined housing do not always guarantee an optimum transition to the connector. Some manufacturers recommend an additional counterbore in the circuit housing to accommodate a solder washer during installation of the seal. JohnsonTM does not recommend this type of installation because if the counterbore is not completely filled with solder, electrical discontinuities may be created.

    3. The transition between the hermetic seal pin and the microstrip trace will effect electrical performance, as stated above. Several different methods of hermetic seal mounting and seal pin to microstrip trace attachment are used in lbe industry.

    Sea Level 70K Feet

    After EnvironmentalInitial

    Single 2.92mm Connector, Calculated Seal Pin & Two 2.92mm Connectors

  • 50 Ohm Connectors - Inches (Millimeters) - Customer Drawings Available Upon Request6

    2.92mm Connectors

    Stainless Steel/Passivated Impedance Max Frequency VSWR

    145-0701-802 50 Ohms 40GHz 1.50

    End Launch Jack - Screw-On Type

    ���������

    ���������

    UNLESS OTHERWISE SPECIFIEDUNITS: INCH

    �����

    �������

    DO NOT SCALEDRAWING

    ������

    ���������

    ����

    ��������������������

    ����������������

    Sheet 1 of 1����

    �����������

    ���������

    This PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is nottraced or copied without

    permission and is returnableupon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009. C

    .XX �.02.XXX �.005

    ANGLES �2 DEG

    REV ECO DATE

    1 ECO-17-0010 4/10/2017

    RoHS2 2011/65/EU

    1R.SHENSEE NOTE

    SEE NOTE

    4/10/17

    END LAUNCH JACKSCREW-ON TYPE SMK(2.92mm)

    145-0701-802

    SPECIFICATION:

    ELECTRICAL: IMPEDANCE: 50 OHMS FREQUENCY RANGE: 0-40 GHz VSWR: DEPENDANT ON APPLICATION WORKING VOLTAGE: 250 VRMS MAX AT SEA LEVEL DIELECTRIC WITHSTANDING VOLTAGE: 750 VRMS MIN AT SEA LEVEL INSULATION RESISTANCE: 5000 MEGOHM MIN CONTACT RESISTANCE: CENTER CONTACT - INITIAL 3 MILLIOHM MAX, AFTER ENVIRONMENTAL NOT APPLICABLE OUTER CONDUCTOR - INITIAL 2 MILLIOHM MAX, AFTER ENVIRONMENTAL NOT APPLICABLE RF LEAKAGE: -90dB TYPICAL AT 2.5GHz

    MECHANICAL: ENGAGEMENT/DISENGAGEMENT FORCE: 2 INCH-POUNDS MAX CONTACT RETENTION: 6 LBS MIN AXIAL FORCE

    MATING TORQUE: 7 TO 10 INCH-POUNDS DURABILITY: 500 CYCLES MIN

    ENVIRONMENTAL: OPERATING TEMPERATUR: -40 TO 85°C THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B CORROSION: MIL-STD-202, METHOD 101, CONDITION B SHOCK: MIL-STD-202, METHOD 213, CONDITION I VIBRATION: MIL-STD-202, METHOD 204, CONDITION D MOISTURE RESISTANCE: MIL-STD-202, MEHTOD 106

    PART NUMBER

    145-0701-802 BRASSNICKEL PL.00007 MINOVER COPPER STRIKE

    ITEM 1MAIN BODY

    ITEM 3CONTACT

    ITEM 4INSULATOR

    ULTEM 1000 (MATINGEND)/TEFLON (SOLDER END)

    BERYLLIUM COPPERGOLD PL .00004 MIN(MATING END)/ .00003 MIN(SOLDER END) OVERNICKEL PL.00005 MIN OVERCOPPER PL.00005 MIN

    NOTE: THIS PATTERN IS FOR REFERENCE ONLY.PATTERN MAY VARY DEPENDING ON BOARD TYPE, SPECIFICELECTRICAL OR MECHANICAL REQUIREMENTS.

    RECOMMENDED PCB LAYOUT

    .375

    .110

    � .0792 X

    .340

    .340

    .500�

    .749

    .378

    .394

    .148

    SEE DETAIL A

    DETAIL A

    .007�

    .012�

    .039�

    1/4-36UNS-2A

    2X #1-72 SCREWS X .445" LENGTH(.062 HEX)

    .375

    .188

    ITEM 5BOLT X 2

    STAINLESSSTEEL

    ITEM 6WASHER X 2

    STAINLESSSTEEL .030

    5*

    6*

    4*

    4*

    1*

    3*

    ITEM 2MOUNTING BODY

    STAINLESS STEELPASSIVATED

    2*

    3*

    Stainless Steel/Passivated Impedance Max Frequency VSWR

    145-0801-802 50 Ohms 40GHz 1.50

    End Launch Plug - Screw-On Type

    ���������

    ���������

    UNLESS OTHERWISE SPECIFIEDUNITS: INCH

    �����

    �������

    DO NOT SCALEDRAWING

    ������

    ���������

    ����

    ��������������������

    ����������������

    Sheet 1 of 1����

    �����������

    ���������

    This PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is nottraced or copied without

    permission and is returnableupon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009. C

    .XX �.02.XXX �.005

    ANGLES �2 DEG

    REV ECO DATE

    1 ECO-17-0010 4/10/2017

    RoHS2 2011/65/EU

    1R.SHENSEE NOTE

    SEE NOTE

    4/10/17

    END LAUNCH PLUGSCREW-ON TYPE SMK(2.92mm)

    145-0801-802

    SPECIFICATION:

    ELECTRICAL: IMPEDANCE: 50 OHMS FREQUENCY RANGE: 0-40 GHz VSWR: DEPENDANT ON APPLICATION WORKING VOLTAGE: 250 VRMS MAX AT SEA LEVEL DIELECTRIC WITHSTANDING VOLTAGE: 750 VRMS MIN AT SEA LEVEL INSULATION RESISTANCE: 5000 MEGOHM MIN CONTACT RESISTANCE: CENTER CONTACT - INITIAL 3 MILLIOHM MAX, AFTER ENVIRONMENTAL NOT APPLICABLE OUTER CONDUCTOR - INITIAL 2 MILLIOHM MAX, AFTER ENVIRONMENTAL NOT APPLICABLE RF LEAKAGE: -90dB TYPICAL AT 2.5GHz

    MECHANICAL: ENGAGEMENT/DISENGAGEMENT FORCE: 2 INCH-POUNDS MAX CONTACT RETENTION: 6 LBS MIN AXIAL FORCE

    MATING TORQUE: 7 TO 10 INCH-POUNDS DURABILITY: 500 CYCLES MIN

    ENVIRONMENTAL: OPERATING TEMPERATUR: -40 TO 85°C THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B CORROSION: MIL-STD-202, METHOD 101, CONDITION B SHOCK: MIL-STD-202, METHOD 213, CONDITION I VIBRATION: MIL-STD-202, METHOD 204, CONDITION D MOISTURE RESISTANCE: MIL-STD-202, MEHTOD 106

    NOTE: THIS PATTERN IS FOR REFERENCE ONLY.PATTERN MAY VARY DEPENDING ON BOARD TYPE, SPECIFICELECTRICAL OR MECHANICAL REQUIREMENTS.

    RECOMMENDED PCB LAYOUT

    .375

    .110

    � .0792 X

    .315 HEX

    2X #1-72 SCREWS X .445" LENGTH(.062 HEX)

    .500�

    .340

    .340.394

    .148

    .375

    .188.879

    .508

    1/4-36UNS-2B SEE DETAIL A

    DETAIL A

    .007�

    .012�

    .039�

    .030

    PART NUMBER

    BRASSNICKEL PL.00007 MINOVER COPPER STRIKE

    ITEM 1MAIN BODY

    ITEM 3CONTACT

    ITEM 4INSULATOR

    ULTEM 1000 (MATINGEND)/TEFLON (SOLDER END)

    BERYLLIUM COPPERGOLD PL .00004 MIN(MATING END)/ .00003 MIN(SOLDER END) OVERNICKEL PL.00005 MIN OVERCOPPER PL.00005 MIN

    ITEM 5BOLT X 2

    STAINLESSSTEEL

    ITEM 6WASHER X 2

    STAINLESSSTEEL

    ITEM 2MOUNTING BODY

    STAINLESS STEELPASSIVATED

    PART NUMBER

    145-0801-802 BRASSNICKEL PL.00007 MINOVER COPPER STRIKE

    ITEM 1MAIN BODY

    ITEM 3CONTACT

    ITEM 4INSULATOR

    ULTEM 1000 (MATINGEND)/TEFLON (SOLDER END)

    BERYLLIUM COPPERGOLD PL .00004 MIN(MATING END)/ .00003 MIN(SOLDER END) OVERNICKEL PL.00005 MIN OVERCOPPER PL.00005 MIN

    ITEM 5BOLT X 2

    STAINLESSSTEEL

    ITEM 6WASHER X 2

    STAINLESSSTEEL

    ITEM 2MOUNTING BODY

    STAINLESS STEELPASSIVATED

    5*

    6*

    4*

    4*

    1*

    3*

    2*

    3*

    Stainless Steel/Passivated Impedance Max Frequency VSWR

    145-0701-811 50 Ohms 40GHz 1.50

    End Launch Jack - Solder Type

    UNLESS OTHERWISE SPECIFIEDUNITS: MM

    DO NOT SCALEDRAWING

    Sheet 1 of 1

    This PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is nottraced or copied without

    permission and is returnableupon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009. C

    X 0.2X.X 0.1

    X.XX 0.07ANGLES 2 DEG

    REV ECO DATE

    0 ECO-16-XXXX 9/15/2016

    RoHS2 2011/65/EU

    0R.SHENSEE NOTE

    SEE NOTE

    9/15/16

    2.92mm END LAUNCH JACK

    145-0701-811

    5:1

    .236

    .586

    .079

    .164

    .010

    .272

    .353

    .032

    .020

    1/4-36 UNS-2A

    SPECIFICATION:

    IMPEDANCE: 50 OHMS FREQUENCY RANGE: 0-40 GHz VSWR: 1.5 MAX

    INSERTION LOSS: 0.05 F dB MAX (F IN GHz) WORKING VOLTAGE: 250 VRMS MAX AT SEA LEVEL DIELECTRIC WITHSTANDING VOLTAGE: 1000VRMS MIN AT SEA LEVEL INSULATION RESISTANCE: 5000 MEGOHM MIN CONTACT RESISTANCE: CENTER CONTACT - INITIAL 3 MILLIOHM MAX, AFTER ENVIRONMENTAL NOT APPLICABLE OUTER CONDUCTOR - INITIAL 2 MILLIOHM MAX, AFTER ENVIRONMENTAL NOT APPLICABLE RF LEAKAGE: -90dB TYPICAL AT 2.5GHz

    MECHANICAL:

    ENGAGEMENT/DISENGAGEMENT FORCE: 2 INCH-POUNDS MAX CONTACT RETENTION: 6 LBS MIN AXIAL FORCE

    MATING TORQUE: 7 TO 10 INCH-POUNDS DURABILITY: 500 CYCLES MIN

    ENVIRONMENTAL:

    OPERATING TEMPERATUR: -40 TO 85°C THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B CORROSION: MIL-STD-202, METHOD 101, CONDITION B SHOCK: MIL-STD-202, METHOD 213, CONDITION I VIBRATION: MIL-STD-202, METHOD 204, CONDITION D MOISTURE RESISTANCE: MIL-STD-202, MEHTOD 106

    PART NUMBER

    145-0701-811BRASSGOLD PL .00005 MINOVER NICKEL PL.00005MIN OVER COPPERPL.00005 MIN

    ITEM 1BODY

    ITEM 2CONTACT

    ITEM 3INSULATOR

    TEFLONBERYLLIUM COPPERGOLD PL .00005 MINOVER NICKEL PL.00005MIN OVER COPPERPL.00005 MIN

    NOTE: THIS PATTERN IS FOR REFERENCE ONLY.PATTERN MAY VARY DEPENDING ON ASSEMBLYPROCESS, BOARD TYPE, OR SPECIFIC ELECTRICAL ORMECHANICAL REQUIREMENTS.

    RECOMMENDED PCB LAYOUT

    .362 MIN

    .396 MIN

    .281

    .276

    .028

    .112

    145-0701-811

    * For more information, please see the drawings on the Cinch website at belfuse.com/Cinch and search by part number.

  • 750 Ohm Connectors - Inches (Millimeters) - Customer Drawings Available Upon Request

    2.92mm Connectors

    2-Hole Flange Mount Jack and Plug Receptacle

    Gold Plated Stainless Steel/Passivated Type Impedance Max Frequency VSWR

    145-0701-601 145-0701 -602 Jack50 Ohms 40GHz

    1.20 (Test result seen on Rogers 3003 board with 0.062” board thickness145-0801-602 Plug

    UNLESS OTHERWISE SPECIFIEDUNITS: INCH

    DO NOT SCALEDRAWING

    Sheet 1 of 1

    This PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is nottraced or copied without

    permission and is returnableupon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009. C

    .XX .02.XXX .005

    ANGLES 2 DEG

    REV ECO DATE

    1 ECO-17-0010 4/10/2017

    RoHS2 2011/65/EU

    1R.SHENSEE NOTE

    SEE NOTE

    4/10/17

    PANEL RECEPTACLE PLUG2-HOLE FLANGE SMK(2.92mm)

    145-0801-602

    SPECIFICATION:

    ELECTRICAL: IMPEDANCE: 50 OHMS FREQUENCY RANGE: 0-40 GHz VSWR: 1.2 MAX. WORKING VOLTAGE: 250 VRMS MAX AT SEA LEVEL DIELECTRIC WITHSTANDING VOLTAGE: 750 VRMS MIN AT SEA LEVEL INSULATION RESISTANCE: 5000 MEGOHM MIN CONTACT RESISTANCE: CENTER CONTACT - INITIAL 3 MILLIOHM MAX, AFTER ENVIRONMENTAL NOT APPLICABLE OUTER CONDUCTOR - INITIAL 2 MILLIOHM MAX, AFTER ENVIRONMENTAL NOT APPLICABLE RF LEAKAGE: -90dB TYPICAL AT 2.5GHz

    MECHANICAL: ENGAGEMENT/DISENGAGEMENT FORCE: 2 INCH-POUNDS MAX CONTACT RETENTION: 6 LBS MIN AXIAL FORCE

    MATING TORQUE: 7 TO 10 INCH-POUNDS DURABILITY: 500 CYCLES MIN

    ENVIRONMENTAL: OPERATING TEMPERATUR: -40 TO 85°C THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B CORROSION: MIL-STD-202, METHOD 101, CONDITION B SHOCK: MIL-STD-202, METHOD 213, CONDITION I VIBRATION: MIL-STD-202, METHOD 204, CONDITION D MOISTURE RESISTANCE: MIL-STD-202, MEHTOD 106

    PART NUMBER

    145-0801-602STAINLESS STEELPASSIVATED

    ITEM 1BODY

    ITEM 2CONTACT

    ITEM 3INSULATOR

    ULTEM 1000BERYLLIUM COPPERGOLD PL .00004 MINOVER NICKEL PL.00005MIN OVER COPPERPL.00005 MIN

    .315 HEX

    ITEM 4NUT

    STAINLESSSTEELPASSIVATED

    ITEM 5GASKET

    SILICONE

    .165

    .065

    .004

    .508 REF

    .481.626

    .224

    .102+.00402 X

    1/4-36UNS-2B

    ACCEPT .012 .001 PIN

    4-Hole Flange Mount Jack and Plug Receptacle

    UNLESS OTHERWISE SPECIFIEDUNITS: INCH

    DO NOT SCALEDRAWING

    Sheet 1 of 1

    This PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is nottraced or copied without

    permission and is returnableupon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009. C

    .XX .02.XXX .005

    ANGLES 2 DEG

    REV ECO DATE

    1 ECO-17-0010 4/10/2017

    RoHS2 2011/65/EU

    1R.SHENSEE NOTE

    SEE NOTE

    4/10/17

    PANEL RECEPTACLE PLUG4-HOLE FLANGE SMK(2.92mm)

    145-0801-612

    SPECIFICATION:

    ELECTRICAL: IMPEDANCE: 50 OHMS FREQUENCY RANGE: 0-40 GHz VSWR: 1.2 MAX. WORKING VOLTAGE: 250 VRMS MAX AT SEA LEVEL DIELECTRIC WITHSTANDING VOLTAGE: 750 VRMS MIN AT SEA LEVEL INSULATION RESISTANCE: 5000 MEGOHM MIN CONTACT RESISTANCE: CENTER CONTACT - INITIAL 3 MILLIOHM MAX, AFTER ENVIRONMENTAL NOT APPLICABLE OUTER CONDUCTOR - INITIAL 2 MILLIOHM MAX, AFTER ENVIRONMENTAL NOT APPLICABLE RF LEAKAGE: -90dB TYPICAL AT 2.5GHz

    MECHANICAL: ENGAGEMENT/DISENGAGEMENT FORCE: 2 INCH-POUNDS MAX CONTACT RETENTION: 6 LBS MIN AXIAL FORCE

    MATING TORQUE: 7 TO 10 INCH-POUNDS DURABILITY: 500 CYCLES MIN

    ENVIRONMENTAL: OPERATING TEMPERATUR: -40 TO 85°C THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B CORROSION: MIL-STD-202, METHOD 101, CONDITION B SHOCK: MIL-STD-202, METHOD 213, CONDITION I VIBRATION: MIL-STD-202, METHOD 204, CONDITION D MOISTURE RESISTANCE: MIL-STD-202, MEHTOD 106

    PART NUMBER

    145-0801-612STAINLESS STEELPASSIVATED

    ITEM 1BODY

    ITEM 2CONTACT

    ITEM 3INSULATOR

    ULTEM 1000BERYLLIUM COPPERGOLD PL .00004 MINOVER NICKEL PL.00005MIN OVER COPPERPL.00005 MIN

    .315 HEX

    ITEM 4NUT

    STAINLESSSTEELPASSIVATED

    ITEM 5GASKET

    SILICONE

    1/4-36UNS-2B

    ACCEPT .012 .001 PIN

    .508 REF

    .065

    .004

    .102+.00404 X

    .340

    .340

    .500

    .165

    Gold Plated Stainless Steel/Passivated Type Impedance Max Frequency VSWR

    145-0701-611 145-0701 -612 Jack50 Ohms 40GHz

    1.20 (Test result seen on Rogers 3003 board with 0.062” board thickness145-0801-612 Plug

  • 50 Ohm Connectors - Inches (Millimeters) - Customer Drawings Available Upon Request8

    2.92mm Connectors

    Hermetic Seal Feedthru

    Jack Receptacle - Thread Mount Field Replaceable

    Accepts Pin Size Gold Plated Stainless Steel/Passivated

    .0120 +/- .0005 (0.305 +/- .013) 145-0701-001 145-0701 -002

    Part Number Item 1 - Outer Ring Item 2 - Insulator Item 3 - Pin Environmental Electrical

    142-1000-033 Kovar Gold pl .00005 min. over Nickel pl .00005 min.

    Glass Corning 7070 or equivalent

    Kovar Gold pl .00005 min. over Nickel pl .00005 min.

    Hermeticity: 1x10-8 cc/sec at one atmosphere

    Solderability: MIL-STD-202, Method 209 Operating

    Temperature: -55° C to 165° C

    Impedance: 50 OhmsFrequency Range: DC to 40 GHzVSWR: Dependent upon application

    Working Voltage: 250 Vrms max at sea level

    Dielectric Withstanding Voltage: 500 Vrms min. at sea level

    Insulation Resistance: 5000 Megohm min.

    Insertion Loss: 0.2 dB max at 40 GHzNotes:1. The hermetic seal should be mounted as flush as possible with the housing. Excessive recession will create a high impedance air gap between connection and housing which degrades electrical performance.

    2. The use of an additional counterbore to accommodate a solder ring for seal mounting is not recommended. A slight chamfer may be used if care is taken to completely fill the area with solder - avoid air gaps.

    Cable Type Gold Plated Stainless Steel/Passivated

    .086 Semi-Rigid (RG-405) 145-0693-001 145-0693-002

    .141 Semi-Rigid (RG-402) 145-0694-001 145-0694-002

    Notes:1. Stainless steel/passivated coupling nut & gold plated body.

    2. Assembly instructions on page 12.

    Straight Solder Type Plug - with contact, slide-on nut

  • 950 Ohm Connectors - Inches (Millimeters) - Customer Drawings Available Upon Request

    2.92mm Adapters Same Series Adapters

    Gold Plated Impedance Max Frequency VSWR

    145-0901-821 50 Ohms 40GHz 1.20

    Plug to Plug Same-Series Adapter

    Gold Plated Impedance Max Frequency VSWR

    145-0901-811 50 Ohms 40GHz 1.20

    Plug to Jack Same-Series Adapter

    Gold Plated Impedance Max Frequency VSWR

    145-0901-801 50 Ohms 40GHz 1.20

    Jack to Jack Same-Series Adapter

    2.92mm Adapters are offered in Same Series and Between Series configurations. They are precision manufactured to RF component industry specifications, with a maximum frequency of 40 GHz.

  • 50 Ohm Connectors - Inches (Millimeters) - Customer Drawings Available Upon Request10

    2.92mm to SMA Adapters Between Series Adapters

    Cage Code

    Drawn by:

    Date: DO NOT SCALEDRAWING

    Title:

    Model No.

    Rev.

    3RD ANGLE PROJECTION

    SizeSheet 1 of 1

    Drawing No.

    Betty.Yu

    10/10/2017

    001Workmanship Std:

    NONE

    UNLESS OTHERWISE SPECIFIEDUNITS: INCH

    JohnsonThis PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is nottraced or copied without

    permission and is returnableupon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009.

    ADAPTER ASSEMBLY,SMK(2.92mm) JACK TO SMA PLUG

    134-1010-001

    134-1010-001

    C

    REV ECO DATE001 ECO-17-0032 11/28/2017

    RoHS2 2011/65/EU

    .XXX u.02.XXXX u.01

    ANGLES u5v

    MODEL NO.

    134-1010-001 ONE PCS PER BAG

    PACKAGING

    NOTES: UNLESS OTHERWISE SPECIFIED

    1. MATERIAL & FINISH: 1.1 BODY & SHELL: PASSIVATED STAINLESS STEEL 1.2 CONTACT PIN : GOLD PLATED BERYLLIUM COPPER 1.3 INSULATOR: PTFE WHITE 1.4 C RING: BERYLLIUM COPPER 1.5 GASKET: SILICONE RED

    2. ELECTRICAL: 2.1 IMPEDANCE: 50 OHMS 2.2 FREQUENCY RANGE: 0-26.5 GHz 2.3 VOLTAGE STANDING WAVE RATIO: 1.3 MAX 2.4 DIELECTRIC WITHSTADING VOLTAGE: 750 VRMS MIN 2.5 CONTACT RESISTANCE: 2.5.1 CENER CONTACT: 3 MILLIOHM MAX 2.5.2 OUTER CONTACT: 2 MILLIOHM MAX 2.6 INSULATOR RESISTANCE: 5000 MEGOHM MIN

    3. MECHANICAL: 3.1 ENGAGEMENT / DISENGAGEMENT FORCE: 2 IN-LBS MAX 3.2 COUPLING NUT RETENTION: 60 LBS MIN 3.3 COUPLING PROOF TORQUE: 15 IN-LBS MIN 3.4 CONTACT RETENTION: 6 LBS. MIN 3.5 DURABILITY: 500 CYCLES MIN.

    4. ENVIRONMENT: 4.1 THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B. 4.2 OPERATING TEMPERATURE: -55TO 125°C 4.3 SALT SPRAY: MIL-STD-202, METHOD 101, CONDITION B 4.4 SHOCK: MIL-STD-202, METHOD 213, CONDITION I 4.5 VIBRATION: MIL-STD-202, METHOD 204, CONDITION D 4.6 MOISTURE RESISTANCE: MIL-STD-202, METHOD 106

    .315 HEX.274 A/F

    1/4-36UNS-2A 1/4-36UNS-2B.744 REF

    .938 REF

    LASER MARK:"1341010001"

    数字签名人 [email protected][email protected]日期:2017.12.05 13:53:50 +08'00'

    Type Stainless Steel/Passivated Impedance Max Frequency VSWR

    2.92mm/SMA 134-1010-000 50 Ohms 26.5GHz 1.30

    Between-Series, 2.92mm Jack To SMA Jack

    Type Stainless Steel/Passivated Impedance Max Frequency VSWR

    2.92mm/SMA 134-1010-002 50 Ohms 26.5GHz 1.30

    Between-Series, 2.92mm Jack To SMA Plug

    Type Stainless Steel/Passivated Impedance Max Frequency VSWR

    2.92mm/SMA 134-1010-001 50 Ohms 26.5GHz 1.30

    Between-Series, 2.92mm Plug To SMA Jack

    Cage Code

    Drawn by:

    Date: DO NOT SCALEDRAWING

    Title:

    Model No.

    Rev.

    3RD ANGLE PROJECTION

    SizeSheet 1 of 1

    Drawing No.

    Betty.Yu

    10/10/2017

    001Workmanship Std:

    NONE

    UNLESS OTHERWISE SPECIFIEDUNITS: INCH

    JohnsonThis PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is not

    traced or copied withoutpermission and is returnable

    upon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009.

    ADAPTER ASSEMBLY,SMK(2.92mm) JACK TO SMA JACK

    134-1010-000

    134-1010-000

    C

    REV ECO DATE001 ECO-17-0032 11/28/2017

    RoHS2 2011/65/EU

    .XXX u.02.XXXX u.01

    ANGLES u5v

    MODEL NO.

    134-1010-000 ONE PCS PER BAG

    PACKAGING

    NOTES: UNLESS OTHERWISE SPECIFIED

    1. MATERIAL & FINISH: 1.1 BODY: PASSIVATED STAINLESS STEEL 1.2 CONTACT PIN: GOLD PLATED BERYLLIUM COPPER 1.3 INSULATOR: PTFE WHITE

    2. ELECTRICAL: 2.1 IMPEDANCE: 50 OHMS 2.2 FREQUENCY RANGE: 0-26.5 GHz 2.3 VOLTAGE STANDING WAVE RATIO: 1.3 MAX 2.4 DIELECTRIC WITHSTADING VOLTAGE: 750 VRMS MIN 2.5 CONTACT RESISTANCE: 2.5.1 CENER CONTACT: 3 MILLIOHM MAX 2.5.2 OUTER CONTACT: 2 MILLIOHM MAX 2.6 INSULATOR RESISTANCE: 5000 MEGOHM MIN

    3. MECHANICAL: 3.1 ENGAGEMENT/DISENGAGEMENT FORCE: 2 IN-LBS. MAX

    3.2 CONTACT RETENTION: 6 LBS MIN 3.3 DURABILITY: 500 CYCLES MIN

    4. ENVIRONMENT: 4.1 THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B. 4.2 OPERATING TEMPERATURE: -55TO 125°C 4.3 SALT SPRAY: MIL-STD-202, METHOD 101, CONDITION B 4.4 SHOCK: MIL-STD-202, METHOD 213, CONDITION I 4.5 VIBRATION: MIL-STD-202, METHOD 204, CONDITION D 4.6 MOISTURE RESISTANCE: MIL-STD-202, METHOD 106

    .274 A/F

    1/4-36UNS-2A

    .274 A/F

    1/4-36UNS-2A

    .896 REF

    LASER MARK:"1341010000"

    数字签名人 [email protected][email protected]日期:2017.12.05 13:53:27 +08'00'

    Type Stainless Steel/Passivated Impedance Max Frequency VSWR

    2.92mm/SMA 134-1010-003 50 Ohms 26.5GHz 1.30

    Between-Series, 2.92mm Plug To SMA Plug

    Cage Code

    Drawn by:

    Date: DO NOT SCALEDRAWING

    Title:

    Model No.

    Rev.

    3RD ANGLE PROJECTION

    SizeSheet 1 of 1

    Drawing No.

    Betty.Yu

    10/10/2017

    001Workmanship Std:

    NONE

    UNLESS OTHERWISE SPECIFIEDUNITS: INCH

    JohnsonThis PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is nottraced or copied without

    permission and is returnableupon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009.

    ADAPTER ASSEMBLY,SMK(2.92mm)PLUG TO SMA JACK

    134-1010-002

    134-1010-002

    C

    REV ECO DATE001 ECO-17-0032 11/28/2017

    RoHS2 2011/65/EU

    .XXX u.02.XXXX u.01

    ANGLES u5v

    MODEL NO.

    134-1010-002 ONE PCS PER BAG

    PACKAGING

    NOTES: UNLESS OTHERWISE SPECIFIED

    1. MATERIAL & FINISH: 1.1 BODY & SHELL: PASSIVATED STAINLESS STEEL 1.2 CONTACT PIN: GOLD PLATED BERYLLIUM COPPER 1.3 INSULATOR: PTFE WHITE 1.4 C RING: BERYLLIUM COPPER 1.5 GASKET: SILICONE RED

    2. ELECTRICAL: 2.1 IMPEDANCE: 50 OHMS 2.2 FREQUENCY RANGE: 0-26.5 GHz 2.3 VOLTAGE STANDING WAVE RATIO: 1.3 MAX 2.4 DIELECTRIC WITHSTADING VOLTAGE: 750 VRMS MIN 2.5 CONTACT RESISTANCE: 2.5.1 CENER CONTACT: 3 MILLIOHM MAX 2.5.2 OUTER CONTACT: 2 MILLIOHM MAX 2.6 INSULATOR RESISTANCE: 5000 MEGOHM MIN

    3. MECHANICAL: 3.1 ENGAGEMENT / DISENGAGEMENT FORCE: 2 IN-LBS. MAX 3.2 COUPLING NUT RETENTION: 60 LBS. MIN 3.3 COUPLING PROOF TORQUE: 15 IN-LBS. MIN 3.4 CONTACT RETENTION: 6 LBS MIN 3.5 DURABILITY: 500 CYCLES MIN

    4. ENVIRONMENT: 4.1 THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B. 4.2 OPERATING TEMPERATURE: -55TO 125°C 4.3 SALT SPRAY: MIL-STD-202, METHOD 101, CONDITION B 4.4 SHOCK: MIL-STD-202, METHOD 213, CONDITION I 4.5 VIBRATION: MIL-STD-202, METHOD 204, CONDITION D 4.6 MOISTURE RESISTANCE: MIL-STD-202, METHOD 106

    1/4-36UNS-2B

    .315 HEX

    .744 REF

    .938 REF

    .274 A/F.274 A/F

    1/4-36UNS-2A

    LASER MARK:"1341010002"

    数字签名人 [email protected][email protected]日期:2017.12.05 13:54:25 +08'00'

    Cage Code

    Drawn by:

    Date: DO NOT SCALEDRAWING

    Title:

    Model No.

    Rev.

    3RD ANGLE PROJECTION

    SizeSheet 1 of 1

    Drawing No.

    Betty.Yu

    10/10/2017

    001Workmanship Std:

    NONE

    UNLESS OTHERWISE SPECIFIEDUNITS: INCH

    JohnsonThis PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is nottraced or copied without

    permission and is returnableupon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009.

    ADAPTER ASSEMBLY,2.92mm(SMK) PLUG TO SMA PLUG

    134-1010-003

    134-1010-003

    C

    REV ECO DATE001 ECO-17-0032 11/28/2017

    RoHS2 2011/65/EU

    .XXX u.02.XXXX u.01

    ANGLES u5v

    MODEL NO.

    134-1010-003 ONE PCS PER BAG

    PACKAGING

    NOTES: UNLESS OTHERWISE SPECIFIED

    1. MATERIAL & FINISH: 1.1 BODY & SHELL: PASSIVATED STAINLESS STEEL 1.2 CONTACT PIN : GOLD PLATED BERYLLIUM COPPER 1.3 INSULATOR: PTFE WHITE 1.4 C RING: BERYLLIUM COPPER 1.5 GASKET: SILICONE RED

    2. ELECTRICAL: 2.1 IMPEDANCE: 50 OHMS 2.2 FREQUENCY RANGE: 0-26.5 GHz 2.3 VOLTAGE STANDING WAVE RATIO: 1.3 MAX 2.4 DIELECTRIC WITHSTANDING VOLTAGE: 750 VRMS MIN 2.5 CONTACT RESISTANCE: 2.5.1 CENTER CONTACT: 3 MILLIOHM MAX 2.5.2 OUTER CONTACT: 2 MILLIOHM MAX 2.6 INSULATOR RESISTANCE: 5000 MEGOHM MIN

    3. MECHANICAL: 3.1 ENGAGEMENT / DISENGAGEMENT FORCE: 2 IN-LBS. MAX 3.2 COUPLING NUT RETENTION: 60 LBS. MIN 3.3 COUPLING PROOF TORQUE: 15 IN-LBS. MIN 3.4 CONTACT RETENTION: 6 LBS. MIN 3.5 DURABILITY: 500 CYCLES MIN

    4. ENVIRONMENT: 4.1 THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B. 4.2 OPERATING TEMPERATURE: -55TO 125°C 4.3 SALT SPRAY: MIL-STD-202, METHOD 101, CONDITION B 4.4 SHOCK: MIL-STD-202, METHOD 213, CONDITION I 4.5 VIBRATION: MIL-STD-202, METHOD 204, CONDITION D 4.6 MOISTURE RESISTANCE: MIL-STD-202, METHOD 106

    .315 HEX.274 A/F

    1/4-36UNS-2B 1/4-36UNS-2B

    .315 HEX

    .744 REF

    .980 REF

    LASER MARK:"1341010003"

    数字签名人 [email protected][email protected]日期:2017.12.05 13:54:48 +08'00'

  • 1150 Ohm Connectors - Inches (Millimeters) - Customer Drawings Available Upon Request

    2.92mm to SMP Adapters Between Series Adapters

    Type Stainless Steel/Passivated Impedance Max Frequency VSWR

    2.92mm/SMP 134-1000-001 50 Ohms 40GHz 1.25

    Between-Series, 2.92mm Jack To SMP Jack

    Type Stainless Steel/Passivated Impedance Max Frequency VSWR

    2.92mm/SMP 134-1000-000 50 Ohms 40GHz 1.25

    Between-Series, 2.92mm Jack To SMP Plug

    Cage Code

    Drawn by:

    Date: DO NOT SCALEDRAWING

    Title:

    Model No.

    Rev.

    3RD ANGLE PROJECTION

    SizeSheet 1 of 1

    Drawing No.

    Betty.Yu

    10/10/2017

    001Workmanship Std:

    NONE

    UNLESS OTHERWISE SPECIFIEDUNITS: INCH

    JohnsonThis PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is not

    traced or copied withoutpermission and is returnable

    upon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009.

    ADAPTER ASSEMBLY, SMK(2.92mm) JACK TOSMP PLUG (LIMITED DETENT)

    134-1000-001

    134-1000-001

    C

    REV ECO DATE001 ECO-17-0032 11/28/2017

    RoHS2 2011/65/EU

    .XXX u.02.XXXX u.01

    ANGLES u5v

    MODEL NO.

    134-1000-001 ONE PCS PER BAG

    PACKAGING

    NOTES: UNLESS OTHERWISE SPECIFIED

    1. MATERIAL & FINISH: 1.1 BODY & CONTACT BODY: PASSIVATED STAINLESS STEEL 1.2 CONTACT PIN : GOLD PLATED BERYLLIUM COPPER 1.3 INSULATOR: PEEK NATURAL

    2. ELECTRICAL: 2.1 IMPEDANCE: 50 OHMS 2.2 FREQUENCY RANGE: 0-40 GHz 2.3 VOLTAGE STANDING WAVE RATIO: 1.25 MAX 2.4 DIELECTRIC WITHSTADING VOLTAGE: 500 VRMS MIN 2.5 CONTACT RESISTANCE: 2.5.1 CENER CONTACT: 6 MILLIOHM MAX 2.5.2 OUTER CONTACT: 2 MILLIOHM MAX 2.6 INSULATOR RESISTANCE: 5000 MEGOHM MIN

    3. MECHANICAL: 3.1 ENGAGEMENT FORCE: 0.23NM MAX (SMK), 45 N MAX (SMP) 3.2 DISENGAGEMENT FORCE: 0.23NM MAX (SMK), 9N MIN (SMP) 3.3 CONTACT RETENTION: 22N MIN 3.4 DURABILITY: 500 CYCLES MIN.

    4. ENVIRONMENT: 4.1 THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B. 4.2 OPERATING TEMPERATURE: -55TO 125°C 4.3 SALT SPRAY: MIL-STD-202, METHOD 101, CONDITION B 4.4 SHOCK: MIL-STD-202, METHOD 213, CONDITION I 4.5 VIBRATION: MIL-STD-202, METHOD 204, CONDITION D 4.6 MOISTURE RESISTANCE: MIL-STD-202, METHOD 106

    .236 A/F

    1/4-36UNS-2A

    O .276

    .514

    .703

    LASER MARK:"1341000001"

    数字签名人 [email protected][email protected]日期:2017.12.05 13:49:50 +08'00'

    Cage Code

    Drawn by:

    Date: DO NOT SCALEDRAWING

    Title:

    Model No.

    Rev.

    3RD ANGLE PROJECTION

    SizeSheet 1 of 1

    Drawing No.

    Betty.Yu

    10/10/2017

    001Workmanship Std:

    NONE

    UNLESS OTHERWISE SPECIFIEDUNITS: INCH

    JohnsonThis PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is not

    traced or copied withoutpermission and is returnable

    upon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009.

    ADAPTER ASSEMBLY, SMK(2.92mm) JACK TO SMP JACK

    134-1000-000

    134-1000-000

    C

    REV ECO DATE001 ECO-17-0032 11/28/2017

    RoHS2 2011/65/EU

    .XXX u.02.XXXX u.01

    ANGLES u5v

    MODEL NO.

    134-1000-000 ONE PCS PER BAG

    PACKAGING

    NOTES: UNLESS OTHERWISE SPECIFIED

    1. MATERIAL & FINISH: 1.1 BODY: PASSIVATED STAINLESS STEEL 1.2 CONTACT PIN, RING & CONTACT BODY: GOLD PLATED BERYLLIUM COPPER 1.3 INSULATOR: PEEK NATURAL

    2. ELECTRICAL: 2.1 IMPEDANCE: 50 OHMS 2.2 FREQUENCY RANGE: 0-40 GHz 2.3 VOLTAGE STANDING WAVE RATIO: 1.25 MAX 2.4 DIELECTRIC WITHSTADING VOLTAGE: 500 VRMS MIN 2.5 CONTACT RESISTANCE: 2.5.1 CENER CONTACT: 6 MILLIOHM MAX 2.5.2 OUTER CONTACT: 2 MILLIOHM MAX 2.6 INSULATOR RESISTANCE: 5000 MEGOHM MIN

    3. MECHANICAL: 3.1 ENGAGEMENT FORCE: FULL DETENT 68 N MAX, LIMITED DETENT 45 N MAX, SMOOTH BORE 9 N MAX (SMP) 0.23 NM MAX (SMK) 3.2 DISENGAGEMENT FORCE: FULL DETENT 22 N MIN, LIMITED DETENT 9 N MIN, SMOOTH BORE 2.2 N MIN (SMP)

    0.23 NM MAX (SMK) 3.3 CONTACT RETENTION: 22N MIN 3.4 DURABILITY: 500CYCLES MIN (SMK) FULL DETENT 100 CYCLES MIN, LIMITED DETENT 500 CYCLES MIN, SMOOTH BORE 1000CYCLES MIN (SMP)

    4. ENVIRONMENT: 4.1 THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B. 4.2 OPERATING TEMPERATURE: -55TO 125°C 4.3 SALT SPRAY: MIL-STD-202, METHOD 101, CONDITION B 4.4 SHOCK: MIL-STD-202, METHOD 213, CONDITION I 4.5 VIBRATION: MIL-STD-202, METHOD 204, CONDITION D 4.6 MOISTURE RESISTANCE: MIL-STD-202, METHOD 106

    .236 A/F

    1/4-36UNS-2A

    .276O

    .514

    .590

    LASER MARK " 1341000000"

    数字签名人 [email protected][email protected]日期:2017.12.05 13:49:17 +08'00'

    Cage Code

    Drawn by:

    Date: DO NOT SCALEDRAWING

    Title:

    Model No.

    Rev.

    3RD ANGLE PROJECTION

    SizeSheet 1 of 1

    Drawing No.

    Betty.Yu

    10/10/2017

    001Workmanship Std:

    NONE

    UNLESS OTHERWISE SPECIFIEDUNITS: INCH

    JohnsonThis PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is not

    traced or copied withoutpermission and is returnable

    upon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009.

    ADAPTER ASSEMBLY, SMK(2.92mm) JACK TO SMP JACK

    134-1000-000

    134-1000-000

    C

    REV ECO DATE001 ECO-17-0032 11/28/2017

    RoHS2 2011/65/EU

    .XXX u.02.XXXX u.01

    ANGLES u5v

    MODEL NO.

    134-1000-000 ONE PCS PER BAG

    PACKAGING

    NOTES: UNLESS OTHERWISE SPECIFIED

    1. MATERIAL & FINISH: 1.1 BODY: PASSIVATED STAINLESS STEEL 1.2 CONTACT PIN, RING & CONTACT BODY: GOLD PLATED BERYLLIUM COPPER 1.3 INSULATOR: PEEK NATURAL

    2. ELECTRICAL: 2.1 IMPEDANCE: 50 OHMS 2.2 FREQUENCY RANGE: 0-40 GHz 2.3 VOLTAGE STANDING WAVE RATIO: 1.25 MAX 2.4 DIELECTRIC WITHSTADING VOLTAGE: 500 VRMS MIN 2.5 CONTACT RESISTANCE: 2.5.1 CENER CONTACT: 6 MILLIOHM MAX 2.5.2 OUTER CONTACT: 2 MILLIOHM MAX 2.6 INSULATOR RESISTANCE: 5000 MEGOHM MIN

    3. MECHANICAL: 3.1 ENGAGEMENT FORCE: FULL DETENT 68 N MAX, LIMITED DETENT 45 N MAX, SMOOTH BORE 9 N MAX (SMP) 0.23 NM MAX (SMK) 3.2 DISENGAGEMENT FORCE: FULL DETENT 22 N MIN, LIMITED DETENT 9 N MIN, SMOOTH BORE 2.2 N MIN (SMP)

    0.23 NM MAX (SMK) 3.3 CONTACT RETENTION: 22N MIN 3.4 DURABILITY: 500CYCLES MIN (SMK) FULL DETENT 100 CYCLES MIN, LIMITED DETENT 500 CYCLES MIN, SMOOTH BORE 1000CYCLES MIN (SMP)

    4. ENVIRONMENT: 4.1 THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B. 4.2 OPERATING TEMPERATURE: -55TO 125°C 4.3 SALT SPRAY: MIL-STD-202, METHOD 101, CONDITION B 4.4 SHOCK: MIL-STD-202, METHOD 213, CONDITION I 4.5 VIBRATION: MIL-STD-202, METHOD 204, CONDITION D 4.6 MOISTURE RESISTANCE: MIL-STD-202, METHOD 106

    .236 A/F

    1/4-36UNS-2A

    .276O

    .514

    .590

    LASER MARK " 1341000000"

    数字签名人 [email protected][email protected]日期:2017.12.05 13:49:17 +08'00'

    Type Stainless Steel/Passivated Impedance Max Frequency VSWR

    2.92mm/SMP 134-1000-002 50 Ohms 40GHz 1.25

    Between-Series, 2.92mm Plug To SMP Jack

    Between-Series, 2.92mm Plug To SMP Plug

    Type Stainless Steel/Passivated Impedance Max Frequency VSWR

    2.92mm/SMP 134-1000-003 50 Ohms 40GHz 1.25

    Cage Code

    Drawn by:

    Date: DO NOT SCALEDRAWING

    Title:

    Model No.

    Rev.

    3RD ANGLE PROJECTION

    SizeSheet 1 of 1

    Drawing No.

    Betty.Yu

    10/10/2017

    001Workmanship Std:

    NONE

    UNLESS OTHERWISE SPECIFIEDUNITS: INCH

    JohnsonThis PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is nottraced or copied without

    permission and is returnableupon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009.

    ADAPTER ASSEMBLY,SMK(2.92mm) PLUG TOSMP PLUG (LIMITED DETENT)

    134-1000-003

    134-1000-003

    C

    REV ECO DATE001 ECO-17-0032 11/28/2017

    RoHS2 2011/65/EU

    .XXX u.02.XXXX u.01

    ANGLES u5v

    MODEL NO.

    134-1000-003 ONE PCS PER BAG

    PACKAGING

    NOTES: UNLESS OTHERWISE SPECIFIED

    1. MATERIAL & FINISH: 1.1 BODY, CONTACT BODY & SHELL: PASSIVATED STAINLESS STEEL 1.2 CONTACT PIN : GOLD PLATED BERYLLIUM COPPER 1.3 INSULATOR: PEEK NATURAL 1.4 C RING: BERYLLIUM COPPER 1.5 GASKET: SILICONE RED

    2. ELECTRICAL: 2.1 IMPEDANCE: 50 OHMS 2.2 FREQUENCY RANGE: 0-40 GHz 2.3 VOLTAGE STANDING WAVE RATIO: 1.25 MAX 2.4 DIELECTRIC WITHSTADING VOLTAGE: 500 VRMS MIN 2.5 CONTACT RESISTANCE: 2.5.1 CENER CONTACT: 6 MILLIOHM MAX 2.5.2 OUTER CONTACT: 2 MILLIOHM MAX 2.6 INSULATOR RESISTANCE: 5000 MEGOHM MIN

    3. MECHANICAL: 3.1 ENGAGEMENT / DISENGAGEMENT FORCE: 0.23 NM MAX(SMK) , 45 N MAX/ 9N MIN (SMP) 3.2 COUPLING NUT RETENTION: 267 N MIN 3.3 COUPLING PROOF TORQUE: 1.7 NM MIN 3.4 CONTACT RETENTION: 22N MIN 3.5 DURABILITY: 500 CYCLES MIN

    4. ENVIRONMENT: 4.1 THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B. 4.2 OPERATING TEMPERATURE: -55TO 125°C 4.3 SALT SPRAY: MIL-STD-202, METHOD 101, CONDITION B 4.4 SHOCK: MIL-STD-202, METHOD 213, CONDITION I 4.5 VIBRATION: MIL-STD-202, METHOD 204, CONDITION D 4.6 MOISTURE RESISTANCE: MIL-STD-202, METHOD 106

    .236 A/F

    1/4-36UNS-2B

    .315 HEX

    O .276

    .514

    .731 REF

    LASER MARK:"1341000003"

    数字签名人 [email protected][email protected]日期:2017.12.05 13:50:37 +08'00'

    Cage Code

    Drawn by:

    Date: DO NOT SCALEDRAWING

    Title:

    Model No.

    Rev.

    3RD ANGLE PROJECTION

    SizeSheet 1 of 1

    Drawing No.

    Betty.Yu

    10/10/2017

    001Workmanship Std:

    NONE

    UNLESS OTHERWISE SPECIFIEDUNITS: INCH

    JohnsonThis PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is not

    traced or copied withoutpermission and is returnable

    upon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009.

    ADAPTER ASSEMBLY,SMK(2.92mm)PLUG TO SMP JACK

    134-1000-002

    134-1000-002

    C

    REV ECO DATE001 ECO-17-0032 11/28/2017

    RoHS2 2011/65/EU

    .XXX u.02.XXXX u.01

    ANGLES u5v

    MODEL NO.

    134-1000-002 ONE PCS PER BAG

    PACKAGING

    NOTES: UNLESS OTHERWISE SPECIFIED

    1. MATERIAL & FINISH: 1.1 BODY & SHELL: PASSIVATED STAINLESS STEEL 1.2 RING, CONTACT PIN & CONTACT BODY : GOLD PLATED BERYLLIUM COPPER 1.3 INSULATOR: PEEK NATURAL 1.4 C RING: BERYLLIUM COPPER 1.5 GASKET: SILICONE RED

    2. ELECTRICAL: 2.1 IMPEDANCE: 50 OHMS 2.2 FREQUENCY RANGE: 0-40 GHz 2.3 VOLTAGE STANDING WAVE RATIO: 1.25 MAX 2.4 DIELECTRIC WITHSTADING VOLTAGE: 500 VRMS MIN 2.5 CONTACT RESISTANCE: 2.5.1 CENER CONTACT: 6 MILLIOHM MAX 2.5.2 OUTER CONTACT: 2 MILLIOHM MAX 2.6 INSULATOR RESISTANCE: 5000 MEGOHM MIN

    3. MECHANICAL: 3.1 ENGAGEMENT FORCE: FULL DETENT 68 N MAX, LIMITED DETENT 45 N MAX, SMOOTH BORE 9 N MAX (SMP) 0.23 NM MAX (SMK) 3.2 DISENGAGEMENT FORCE: FULL DETENT 22 N MIN, LIMITED DETENT 9 N MIN, SMOOTH BORE 2.2 N MIN (SMP) 0.23 NM MAX (SMK) 3.3 COUPLING NUT RETENTION: 267 N MIN 3.4 COUPLING PROOF TORQUE: 1.7 NM MIN 3.5 CONTACT RETENTION: 22 N MIN 3.6 DURABILITY: 500 CYCLES MIN (SMK) FULL DETENT 100 CYCLES MIN, LIMITED DETENT 500 CYCLES MIN, SMOOTH BORE 1000 CYCLES MIN (SMP)

    4. ENVIRONMENT: 4.1 THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B. 4.2 OPERATING TEMPERATURE: -55TO 125°C 4.3 SALT SPRAY: MIL-STD-202, METHOD 101, CONDITION B 4.4 SHOCK: MIL-STD-202, METHOD 213, CONDITION I 4.5 VIBRATION: MIL-STD-202, METHOD 204, CONDITION D 4.6 MOISTURE RESISTANCE: MIL-STD-202, METHOD 106

    .236 A/F

    1/4-36UNS-2B

    .315 HEX

    .618 REF

    O .276

    .514

    LASER MARK:"1341000002"

    数字签名人 [email protected][email protected]日期:2017.12.05 13:50:13 +08'00'

  • 50 Ohm Connectors - Inches (Millimeters) - Customer Drawings Available Upon Request12

    2.92mm to SMPM Adapters Between Series Adapters

    Cage Code

    Drawn by:

    Date: DO NOT SCALEDRAWING

    Title:

    Model No.

    Rev.

    3RD ANGLE PROJECTION

    SizeSheet 1 of 1

    Drawing No.

    Betty.Yu

    10/10/2017

    001Workmanship Std:

    NONE

    UNLESS OTHERWISE SPECIFIEDUNITS: INCH

    JohnsonThis PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is nottraced or copied without

    permission and is returnableupon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009.

    ADAPTER ASSEMBLY,SMK(2.92mm)JACK TO SMPM JACK

    134-1000-004

    134-1000-004

    C

    REV ECO DATE001 ECO-17-0032 11/28/2017

    RoHS2 2011/65/EU

    .XXX u.02.XXXX u.01

    ANGLES u5v

    MODEL NO.

    134-1000-004 ONE PCS PER BAG

    PACKAGING

    NOTES: UNLESS OTHERWISE SPECIFIED

    1. MATERIAL & FINISH: 1.1 BODY: PASSIVATED STAINLESS STEEL 1.2 CONTACT PIN& CONTACT BODY: GOLD PLATED BERYLLIUM COPPER 1.3 INSULATOR1: ULTEM1000 AMBER 1.4 INSULATOR2: PTFE WHITE

    2. ELECTRICAL: 2.1 IMPEDANCE: 50 OHMS 2.2 FREQUENCY RANGE: 0-40 GHz 2.3 VOLTAGE STANDING WAVE RATIO: 1.3MAX 2.4 DIELECTRIC WITHSTADING VOLTAGE: 325 VRMS MIN 2.5 CONTACT RESISTANCE: 2.5.1 CENER CONTACT: 6 MILLIOHM MAX 2.5.2 OUTER CONTACT: 2 MILLIOHM MAX 2.6 INSULATOR RESISTANCE: 5000 MEGOHM MIN

    3. MECHANICAL: 3.1 ENGAGEMENT FORCE: 0.23 NM MAX (SMK) FULL DETENT 19 N MAX; SMOOTH BORE: 11 N MAX (SMPM) 3.2 DISENGAGEMENT FORCE: 0.23 NM MAX (SMK) FULL DETENT 29 N MAX; SMOOTH BORE: 11 N MAX (SMPM) 3.3 CONTACT RETENTION: 22 N MIN 3.4 DURABILITY: 500 CYCLES MIN (SMK) FULL DETENT 100 CYCLES MIN, SMOOTH BORE: 500 CYCLES MIN (SMPM)

    4. ENVIRONMENT: 4.1 THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B. 4.2 OPERATING TEMPERATURE: -55TO 125°C 4.3 SALT SPRAY: MIL-STD-202, METHOD 101, CONDITION B 4.4 SHOCK: MIL-STD-202, METHOD 213, CONDITION I 4.5 VIBRATION: MIL-STD-202, METHOD 204, CONDITION D 4.6 MOISTURE RESISTANCE: MIL-STD-202, METHOD 106

    .861 REF

    .785

    .315O .354O

    1/4-36UNS-2A .309 A/F.272 A/F

    LASER MARK:"1341000004"

    数字签名人 [email protected][email protected]日期:2017.12.05 13:51:04 +08'00'

    Type Stainless Steel/Passivated Impedance Max Frequency VSWR

    2.92mm/SMPM 134-1000-005 50 Ohms 40GHz 1.25

    Between-Series, 2.92mm Jack To SMPM Jack

    Type Stainless Steel/Passivated Impedance Max Frequency VSWR

    2.92mm/SMPM 134-1000-004 50 Ohms 40GHz 1.25

    Between-Series, 2.92mm Jack To SMPM Plug

    Type Stainless Steel/Passivated Impedance Max Frequency VSWR

    2.92mm/SMPM 134-1000-006 50 Ohms 40GHz 1.25

    Between-Series, 2.92mm Plug To SMPM Jack

    Between-Series, 2.92mm Plug To SMPM Plug

    Type Stainless Steel/Passivated Impedance Max Frequency VSWR

    2.92mm/SMPM 134-1000-007 50 Ohms 40GHz 1.25

    Cage Code

    Drawn by:

    Date: DO NOT SCALEDRAWING

    Title:

    Model No.

    Rev.

    3RD ANGLE PROJECTION

    SizeSheet 1 of 1

    Drawing No.

    Betty.Yu

    10/10/2017

    001Workmanship Std:

    NONE

    UNLESS OTHERWISE SPECIFIEDUNITS: INCH

    JohnsonThis PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is not

    traced or copied withoutpermission and is returnable

    upon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009.

    ADAPTER ASSEMBLY,SMK(2.92mm)JACK TO SMPM PLUG

    134-1000-005

    134-1000-005

    C

    REV ECO DATE001 ECO-17-0032 11/28/2017

    RoHS2 2011/65/EU

    .XXX u.02.XXXX u.01

    ANGLES u5v

    MODEL NO.

    134-1000-005 ONE PCS PER BAG

    PACKAGING

    NOTES: UNLESS OTHERWISE SPECIFIED

    1. MATERIAL & FINISH: 1.1 BODY& COTACT BODY: PASSIVATED STAINLESS STEEL 1.2 CONTACT PIN: GOLD PLATED BERYLLIUM COPPER 1.3 INSULATOR1: ULTEM1000 AMBER 1.4 INSULATOR2: PTFE WHITE

    2. ELECTRICAL: 2.1 IMPEDANCE: 50 OHMS 2.2 FREQUENCY RANGE: 0-40 GHz 2.3 VOLTAGE STANDING WAVE RATIO: 1.3 MAX 2.4 DIELECTRIC WITHSTADING VOLTAGE: 325 VRMS MIN 2.5 CONTACT RESISTANCE: 2.5.1 CENER CONTACT: 6 MILLIOHM MAX 2.5.2 OUTER CONTACT: 2 MILLIOHM MAX 2.6 INSULATOR RESISTANCE: 5000 MEGOHM MIN

    3. MECHANICAL: 3.1 ENGAGEMENT FORCE: 0.23 NM MAX (SMK);FULL DETENT 19 N MAX (SMPM) 3.2 DISENGAGEMENT FORCE: 0.23 NM MAX (SMK); FULL DETENT 29 N MAX (SMPM) 3.3 CONTACT RETENTION: 22 N MIN 3.4 DURABILITY: 500 CYCLES (SMK); FULL DETENT: 100 CYCLES MIN(SMPM)

    4. ENVIRONMENT: 4.1 THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B. 4.2 OPERATING TEMPERATURE: -55TO 125°C 4.3 SALT SPRAY: MIL-STD-202, METHOD 101, CONDITION B 4.4 SHOCK: MIL-STD-202, METHOD 213, CONDITION I 4.5 VIBRATION: MIL-STD-202, METHOD 204, CONDITION D 4.6 MOISTURE RESISTANCE: MIL-STD-202, METHOD 106

    1/4-36UNS-2A.309 A/F

    .272 A/F

    .944 REF

    .785

    .315O .354O

    LASER MARK:"1341000005"

    数字签名人 [email protected][email protected]日期:2017.12.05 13:51:54 +08'00'

    Cage Code

    Drawn by:

    Date: DO NOT SCALEDRAWING

    Title:

    Model No.

    Rev.

    3RD ANGLE PROJECTION

    SizeSheet 1 of 1

    Drawing No.

    Betty.Yu

    10/10/2017

    001Workmanship Std:

    NONE

    UNLESS OTHERWISE SPECIFIEDUNITS: INCH

    JohnsonThis PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is not

    traced or copied withoutpermission and is returnable

    upon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009.

    ADAPTER ASSEMBLY, SMK(2.92mm)PLUG TO SMPM PLUG

    134-1000-007

    134-1000-007

    C

    REV ECO DATE001 ECO-17-0032 11/28/2017

    RoHS2 2011/65/EU

    .XXX u.02.XXXX u.01

    ANGLES u5v

    MODEL NO.

    134-1000-007 ONE PCS PER BAG

    PACKAGING

    NOTES: UNLESS OTHERWISE SPECIFIED

    1. MATERIAL & FINISH: 1.1 BODY,CONTACT BODY& SHELL: PASSIVATED STAINLESS STEEL 1.2 CONTACT PIN: GOLD PLATED BERYLLIUM COPPER 1.3 INSULATOR1: ULTEM1000 AMBER 1.4 INSULATOR2: PTFE WHITE 1.5 C RING: BERYLLIUM COPPER 1.6 GASKET: SILICONE RED

    2. ELECTRICAL: 2.1 IMPEDANCE: 50 OHMS 2.2 FREQUENCY RANGE: 0-40 GHz 2.3 VOLTAGE STANDING WAVE RATIO: 1.23MAX 2.4 DIELECTRIC WITHSTADING VOLTAGE: 325 VRMS MIN 2.5 CONTACT RESISTANCE: 2.5.1 CENER CONTACT: 6 MILLIOHM MAX 2.5.2 OUTER CONTACT: 2 MILLIOHM MAX 2.6 INSULATOR RESISTANCE: 5000 MEGOHM MIN

    3. MECHANICAL: 3.1 ENGAGEMENT FORCE: 0.23NM MAX (SMK),FULL DETENT 19 N MAX (SMPM) 3.2 DISENGAGEMENT FORCE: 0.23NM MAX (SMK),FULL DETENT 29 N MAX (SMPM) 3.3 COUPLING PROOF TORQUE: 1.7 NM MIN. 3.4 COUPLING NUT RETENTION: 267 N MIN 3.5 CONTACT RETENTION: 22 N MIN 3.6 DURABILITY: 500 CYCLES MIN (SMK), FULL DETENT 100 CYCLES MIN (SMPM)

    4. ENVIRONMENT: 4.1 THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B. 4.2 OPERATING TEMPERATURE: -55TO 125°C 4.3 SALT SPRAY: MIL-STD-202, METHOD 101, CONDITION B 4.4 SHOCK: MIL-STD-202, METHOD 213, CONDITION I 4.5 VIBRATION: MIL-STD-202, METHOD 204, CONDITION D 4.6 MOISTURE RESISTANCE: MIL-STD-202, METHOD 106

    .309 A/F.272 A/F

    1/4-36UNS-2B

    .315 HEX

    .972 REF

    .785

    .315O .354O

    LASER MARK:"1341000007"

    数字签名人 [email protected][email protected]日期:2017.12.05 13:53:02 +08'00'

    Cage Code

    Drawn by:

    Date: DO NOT SCALEDRAWING

    Title:

    Model No.

    Rev.

    3RD ANGLE PROJECTION

    SizeSheet 1 of 1

    Drawing No.

    Betty.Yu

    10/10/2017

    001Workmanship Std:

    NONE

    UNLESS OTHERWISE SPECIFIEDUNITS: INCH

    JohnsonThis PROPRIETARY Document is property of Cinch Connectivity

    Solutions. It is confidential innature, non-transferable, and

    issued with the clearunderstanding that it is not

    traced or copied withoutpermission and is returnable

    upon demand.

    INTERPRET DRAWING INACCORDANCE WITH ASME

    Y14.5-2009.

    ADAPTER ASSEMBLY,SMK(2.92mm)PLUG TO SMPM JACK

    134-1000-006

    134-1000-006

    C

    REV ECO DATE001 ECO-17-0032 11/28/2017

    RoHS2 2011/65/EU

    .XXX u.02.XXXX u.01

    ANGLES u5v

    MODEL NO.

    134-1000-006 ONE PCS PER BAG

    PACKAGING

    NOTES: UNLESS OTHERWISE SPECIFIED

    1. MATERIAL & FINISH: 1.1 BODY& SHELL: PASSIVATED STAINLESS STEEL 1.2 CONTACT PIN& CONTACT BODY: GOLD PLATED BERYLLIUM COPPER 1.3 INSULATOR1: ULTEM1000 AMBER 1.4 INSULATOR2: PTFE WHITE 1.5 C RING: BERYLLIUM COPPER 1.6 GASKET: SILICONE RED

    2. ELECTRICAL: 2.1 IMPEDANCE: 50 OHMS 2.2 FREQUENCY RANGE: 0-40 GHz 2.3 VOLTAGE STANDING WAVE RATIO: 1.3 MAX 2.4 DIELECTRIC WITHSTADING VOLTAGE: 325 VRMS MIN 2.5 CONTACT RESISTANCE: 2.5.1 CENER CONTACT: 6 MILLIOHM MAX 2.5.2 OUTER CONTACT: 2 MILLIOHM MAX 2.6 INSULATOR RESISTANCE: 5000 MEGOHM MIN

    3. MECHANICAL: 3.1 ENGAGEMENT FORCE: 0.23 NM MAX (SMK) FULL DETENT 19 N MAX, SMOOTH BORE 11 N MAX (SMPM) 3.2 DISENGAGEMENT FORCE: 0.23 NM MAX (SMK) FULL DETENT 29 N MAX, SMOOTH BORE 11N MAX (SMPM) 3.3 COUPLING PROOF TORQUE: 1.7 NM MIN.(SMK) 3.4 COUPLING NUT RETENTION: 267N MIN 3.5 CONTACT RETENTION: 22 N MIN 3.6 DURABILITY: 500 CYCLES MIN (SMK) FULL DETENT 100 CYCLES MIN, SMOOTH BORE 500 CYCLES MIN (SMPM)

    4. ENVIRONMENT: 4.1 THERMAL SHOCK: MIL-STD-202, METHOD 107, CONDITION B. 4.2 OPERATING TEMPERATURE: -55TO 125°C 4.3 SALT SPRAY: MIL-STD-202, METHOD 101, CONDITION B 4.4 SHOCK: MIL-STD-202, METHOD 213, CONDITION I 4.5 VIBRATION: MIL-STD-202, METHOD 204, CONDITION D 4.6 MOISTURE RESISTANCE: MIL-STD-202, METHOD 106

    .309 A/F.272 A/F

    1/4-36UNS-2B

    .315 HEX

    .890 REF

    .315O .354O

    .785

    LASER MARK:"1341000006"

    数字签名人 [email protected][email protected]日期:2017.12.05 13:52:18 +08'00'

  • 1350 Ohm Connectors - Inches (Millimeters) - Customer Drawings Available Upon Request

    Tooling

    2.92mm Solder Type Straight Plugs For Semi-rigid Cable

    Tool 145-0693-001/002 145-0694-001/002

    (FOR .086 SEMl·RIGID) (FOR 141 SEMI-RIGID)

    Semi-Riaid Cable Vise 140-0000-962 14 0-0000-962

    Vise Stop 140-0000-968 140-0000-968

    Bead Assy. Tool 140-0000-957 140-0000-957

    Contact Soldering Tool 140-0000-960 140-0000-961

    Body Soldering Tool 140-0000-958 140-0000-959

    Cable Clamp Insert 140-0000-964 140-0000-965

    1

    2

    3

    4

    5

    6

    Identify connector parts (5 piece parts) and tools (5 tools.)

    Strip cable jacket and dielectric to dimension shown.

    Place center contact onto center conductor. Slide contact soldering tool onto contact. Clamp the cable contact and tool into cable soldering vise and solder contact to center conductor. High temperature solder, such as 95/5 Sn/Ag is recommended so that contact solder joint remains stable during body soldering operation. Solder paste is recommended for the contact solder joint to minimize excess solder. The assembled dimension should be as shown.

    Remove excess solder from contact with a sharp blade and clean contact. Check for presence of excess solder by sliding body soldering tool over the contact. Remove soldering tool.

    Place connector nut and body on cable. Place connector body soldering tool over contact and thread the coupling nut and connector body firmly to the tool. Place cable subassembly into cable soldering vise. Clamp cable and soldering tool securely to insure the cable dielectric expansion will not disturb the cable in the vise during soldering, Place hot soldering iron on the connector body sleeve and apply solder from the opposite side. A low temp solder, such as 60/40 Sn/Pb is recommended for the body solder joint. Allow the soldered joint to cool and remove from fix ture. Check contact location to the body. The best electrical results are achieved when the contact location is within a to lerance of .060 +/- .001.

    Place bead onto neck portion of the tool. Thread Bead Assembly tool firmly Into the coupling nut. Push the tool’s plunger between your thumb and fingers to assemble the bead. Check bead location. Assemble seal ring onto body.

    1

    2

    3

    4

    5

    6

  • 50 Ohm Connectors - Inches (Millimeters) - Customer Drawings Available Upon Request14

    Assembly Instructions

    Accurate assembly of the 2.92mm Cabled Connectors is obtained with the tools listed below. Industry standard devices are used if possible for customer convenience and tool compatibility.

    Item Part Number Description

    A 140-0000-962 Semi-rigid Cable Vise (does not include inserts(B) or Vise Stop (F))

    B 140-0000-964140-0000-965

    Cable Clamp Inserts, .086 Semi-rigidCable Clamp lnserts, .141 Semi-rigid

    C 140-0000-960140-0000-961

    Contact Soldering Tool, .086 PlugContact Soldering Tool, .141 Plug

    D 140-0000-958140-0000-959

    Body Soldering Tool, .086 PlugBody Soldering Tool, .141 Plug

    E 140-0000-957 Bead Assembly Tool, Semi-rigid Plugs, All Cables

    F 140-0000-968 Vise Stop, (2.92mm)

    2.92mm Tools

  • Notes

    belfuse.com/cinch

  • Innovative Interconnect Solutions Across the Globe

    In operation since 1917, Cinch supplies high quality, high performance

    connectors and cables globally to the Aerospace, Military/Defense,

    Commercial Transportation, Oil & Gas, High End Computer, and other

    markets. We provide custom solutions with our creative, hands on

    engineering and end to end approach.

    Our diverse product offerings include: connectors, enclosures and cable

    assemblies utilizing multiple contact technologies including copper and fiber

    optics. Our product engineering and development activities employ cutting

    edge technologies for design and modeling, and our various technologies

    and expertise enable us to deliver custom solutions and products for our

    strategic partnerships. We also serve a broad range of commercial markets,

    largely through our highly efficient distribution network.

    We aim to exceed our customer’s expectations, and to continually provide

    innovative solutions to the rapidly changing needs of the markets, and

    customers, we serve. For more information, visit belfuse.com/cinch

    Cinch Connectivity Solutions North America OfficeT +1 [email protected]

    Cinch Connectivity Solutions Ltd European OfficeT +44 (0) 1245 [email protected]

    Cinch Connectivity Solutions Asia Pacific OfficeT +86 21 5442 7668

    [email protected]

    © 2018 Cinch Connectivity Solutions ca-ccs-john-2.92mm-catalog 4112018

Click here to load reader

Reader Image
Embed Size (px)
Recommended