3", 4", 6" & 8"Model H Series
Alarm Check ValveInstallation
andMaintenance Guide
4077 AIRPARK DRIVE STANDISH, MICHIGAN 48658PHONE 989-846-4583 800-248-0278
FAX 989-846-9231www.globesprinkler.com
JUNE 2016 C-5 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
Table of Contents
JUNE 2016 Page i BULLETIN A.C.V.I.M., REV. #14
Globe Alarm Check Valves
General Description
Physical Data 3”, 4” & 6” Alarm Check Valve Assembly and Parts List
8” Alarm Check Valve Assembly and Parts List
3” Model “H” Series Vertical Position/Variable Pressure Trim
3” Model “H” Series Vertical Position/Constant Pressure Trim
3” Model “H” Series Horizontal Position/Variable Pressure Trim
3” Model “H” Series Horizontal Position/Constant Pressure Trim
4” Model “H” Series Vertical Position/Variable Pressure Trim
4” Model “H” Series Vertical Position/Constant Pressure Trim
4” Model “H” Series Horizontal Position/Variable Pressure Trim
4” Model “H” Series Horizontal Position/Constant Pressure Trim
6” Model “H” Series Vertical Position/Variable Pressure Trim
6” Model “H” Series Vertical Position/Constant Pressure Trim
6” Model “H” Series Horizontal Position/Variable Pressure Trim
6” Model “H” Series Horizontal Position/Constant Pressure Trim
8” Model “H” Series Vertical Position/Variable Pressure Trim
8” Model “H” Series Vertical Position/Constant Pressure Trim
Optional Alarm Pressure Switch Trim
Pressure Relief Valve for use in Gridded Systems Testing
Maintenance
1
2
3
3
6-7
8-9
10-11
12-13
14-15
16-17
18-19
20-21
22-23
24-25
26-27
28-29
30-31
32-33
34
34
4
5
JUNE 2016 Page 1 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
IMPORTANT NOTES1. Any alarm check valve should be carefully tested, examined, and cleaned periodically in accordance with NFPA 25.2. It is most important to ensure a clean water supply free of debris and solid particles such as sand, gravel, or mud.3. If, during the annual inspection of alarm check valves, sediment or free particles of matter are noted, a further examination of internal valve parts becomes necessary.4. All deposits should be removed from all operating parts and ports. Vent holes through seat ring, Items 3 and 2 (Page 4), should be throroughly cleaned and flushed with clean water.5. Where difficulty in performance is experienced, the manufacturer or his authorized representative shall be contacted if any field adjustment is to be made.
GENERAL DESCRIPTIONGlobe Fire Sprinkler Corporation Alarm Check Valves are used in wet pipe fire sprinkler systems. They primarily serve a dual purpose in that they prevent a reverse flow of water through their bodies (non-return) and also pro-vide for the use of a hydraulic fire alarm which is not dependent upon an electrical power supply for its operation. Through the use of a hydraulic retard chamber a time delay is provided to eliminate potential false alarms caused by fluctuating water supply pressures. Where constant pressure water supplies are used the retard chamber (time delay) is not necessary. By incorporating the use of electrical pressure switches, other supplemental alarms, annunciators, etc. may also be used. Globe Alarm Check Valves are designed and manufactured to the standards and/or requirements of Under-writers Laboratories Inc., Factory Mutual Approvals, The Loss Prevention Certification Board and the City of New York Department of Buildings, and they conform to the design/usage requirements of NFPA 13.
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
JUNE 2016 Page 2 BULLETIN A.C.V.I.M., REV. #14
VERTICAL / VARIABLE
MODEL H-1 H-2 H-3
SIZE 3” 4” 6” 8” 3” 4” 6” 8” 3” 4” 6” 8”
Overall Length 9” 9” 10” 14” 10” 10” 12” 15” 9 1/4” 9 1/2” 11” 15”
Center of Valve to Back 10” 11” 12” 13” 10” 11” 12 1/2” 12” 10” 11” 12” 13”
Center of Valve to Right 13 1/2” 16 1/2” 16 1/2” 16 1/2” 13 1/2” 16 1/2” 17” 17” 13 1/2” 16 1/2” 16 1/2” 16 1/2”
Center of Valve to Left 8” 8” 8” 8” 8” 8” 8 1/4” 9” 8” 8” 8” 8”
Center of Valve to Center of Drain 9 1/4” 8” 8 3/4” 8 3/4” 9 1/4” 8” 9 1/4” 9” 9 1/4” 8” 8 3/4” 8 3/4”
Weight of Valve Complete with all Trimings
34 lbs. 81 lbs.
42 lbs. 89 lbs.
69 lbs. 141 lbs.
147 lbs. 198 lbs.
20 lbs. 57 lbs.
22 lbs. 69 lbs.
46 lbs. 95 lbs.
106 lbs. 157 lbs.
28 lbs. 75 lbs.
37 lbs. 84 lbs.
59 lbs. 100 lbs.
130 lbs. 180 lbs.
VERTICAL / CONSTANT
MODEL H-1 H-2 H-3
SIZE 3” 4” 6” 8” 3” 4” 6” 8” 3” 4” 6” 8”
Overall Length 9” 9” 10” 14” 10” 10” 12” 15” 9 1/4” 9 1/2” 11” 15”
Center of Valve to Back 10” 8 3/4” 9 3/4” 12 1/4” 10” 8 3/4” 10” 12” 10” 8 3/4” 9 3/4” 12 1/4”
Center of Valve to Right 13 1/2” 15 1/2” 16 1/4” 17” 13 1/2” 15 1/2” 17” 17 3/4” 13 1/2” 15 1/2” 16 1/4” 17”
Center of Valve to Left 8” 8” 8” 7 1/2” 8” 8” 8 1/2” 8 3/4” 8” 8” 8” 7 1/2”
Center of Valve to Center of Drain 9 1/4” 8” 8 3/4” 9 1/2” 9 1/4” 8” 9 1/4” 9” 9 1/4” 8” 8 3/4” 9 1/2”
Weight of Valve Complete with all Trimings
34 lbs. 56 lbs.
42 lbs. 64 lbs.
69 lbs. 89 lbs.
147 lbs. 174 lbs.
20 lbs. 57 lbs.
22 lbs. 44 lbs.
46 lbs. 71 lbs.
106 lbs. 132 lbs.
28 lbs. 50 lbs.
37 lbs. 59 lbs.
59 lbs. 75 lbs.
130 lbs. 156 lbs.
HORIZONTAL / VARIABLE
MODEL H-1 H-2 H-3
SIZE 3” 4” 6” 8” 3” 4” 6” 8” 3” 4” 6” 8”
Overall Length 9” 9” 10” N/A 10” 10” 12” N/A 9 1/4” 9 1/2” 11” N/A
Center of Valve to Back 7 1/2” 10 1/4” 20 1/2” N/A 7 1/2” 10 1/4” 10 1/2” N/A 7 1/2” 10 1/4” 20 1/2” N/A
Center of Valve to Right 17 1/2” 17” 18 1/2” N/A 17 1/2” 17” 20 1/2” N/A 17 1/2” 17” 18 1/2” N/A
Center of Valve to Left 7 1/4” 8 1/2” 12” N/A 7 1/4” 8 1/2” 10” N/A 7 1/4” 8 1/2” 12” N/A
Center of Valve to Center of Drain 9 1/2” 13 1/2” 14” N/A 9 1/2” 13 1/2” 13 3/4” N/A 9 1/2” 13 1/2” 14” N/A
Weight of Valve Complete with all Trimings
34 lbs. 89 lbs.
42 lbs. 97 lbs.
69 lbs. 122 lbs. N/A 20 lbs.
70 lbs.22 lbs. 82 lbs.
46 lbs. 100 lbs. N/A 28 lbs.
83 lbs.37 lbs. 92 lbs.
59 lbs. 113 lbs. N/A
HORIZONTAL / CONSTANT
MODEL H-1 H-2 H-3
SIZE 3” 4” 6” 8” 3” 4” 6” 8” 3” 4” 6” 8”
Overall Length 9” 9” 10” N/A 10” 10” 12” N/A 9 1/4” 9 1/2” 11” N/A
Center of Valve to Back 7 1/2” 10” 19 1/2” N/A 7 1/2” 10” 11” N/A 7 1/2” 10” 19 1/2” N/A
Center of Valve to Right 17 1/2” 16 1/2” 15 1/2” N/A 17 1/2” 16 1/2” 19 1/2” N/A 17 1/2” 16 1/2” 15 1/2” N/A
Center of Valve to Left 7 1/4” 8 1/2” 8 3/4” N/A 7 1/4” 8 1/2” 10” N/A 7 1/4” 8 1/2” 8 3/4” N/A
Center of Valve to Center of Drain 12 1/4” 13 1/2” 14” N/A 12 1/4” 13 1/2” 12 3/4” N/A 12 1/4” 13 1/2” 14” N/A
Weight of Valve Complete with all Trimings
34 lbs. 60 lbs.
42 lbs. 68 lbs.
69 lbs. 94 lbs. N/A 20 lbs.
70 lbs.22 lbs. 53 lbs.
46 lbs. 74 lbs. N/A 28 lbs.
54 lbs.37 lbs. 63 lbs.
59 lbs. 85 lbs. N/A
JUNE 2016 Page 3 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
3”, 4” & 6” Alarm Check Valve Assembly
4
2
15
16
3
1
10 12 11
9
18
13
8
6
1414
6
17 5
7
FRONT VIEW TOP VIEW
6
5
9 8
7
11
10
11
1
3
2
4 12 13
8” Alarm Check Valve Assembly
FRONT VIEW TOP VIEW
*DUCTILE IRON FOR 300psi (20bars) RATED VALVES
*DUCTILE IRON FOR 300psi (20bars) RATED VALVES
ITEM DESCRIPTION MATERIAL P/N ITEM DESCRIPTION MATERIAL P/N
1
“H-”1 Body Cast Iron 323832 7 Clapper Disc EPDM 323842
“H-2” Body Cast Iron* 323858 8 Disc Retainer Stainless 323843
“H-3” Body Cast Iron 323851 9 Disc Retainer Bolt Stainless 323838
2 Cover Cast Iron* 323835 10 Hinge Pin Stainless 323845
3 Cover Gasket Rubber 323833 11 Hinge Pin Bushings (2) Bronze 323846
4 Cover Bolts (6) Steel 32383912
175psi Name Plate Aluminum 323847
5 Seat Ring Bronze 323837 300psi Name Plate Aluminum 323787
6 Clapper Bronze 323841 13 Drive Screws (2) Stainless 323420
ITEM DESCRIPTION MATERIAL 3” [80mm]P/N
4” [100mm] P/N
6” / 150mm P/N ITEM DESCRIPTION MATERIAL 3” [80mm]
P/N4” [100mm]
P/N6” / 150mm
P/N
1
“H-1” Body Cast Iron 323803 323502 323562 9 Clapper Facing Disc EPDM 323815 323511 323571
“H-2” Body Cast Iron* 323827 323552 323666/ 323666-D 10 Disc Retainer Stainless 323816 323512 323572
“H-3” Body Cast Iron 323807 323542 323592 11 Lock Nut Stainless 323514 323514 323514
2 Cover Bolt Steel 323408 323509 323569 12 Disc Retainer Bolt Stainless 323817 323513 323573
3 Seat Ring Bronze 323809 323504 323564 13 Sealing Washer Hard Fiber 323515 323515 323515
4 Cover Cast Iron* 323805 323507 323567 14 Hinge Pin Bushings (2) Bronze 323819 323518 323518
5 Clapper Stainless 323814 323510 323507 15 Name Plate Aluminum 323480 323480 323480
6 Retaining Ring Stainless 323527 323517 323517 16 Drive Screws (2) Stainless 323520 323520 323520
7 Hinge Pin Stainless 323818 323516 323516 17 Torsion Spring Stainless 323528 323528 323565
8 Cover Gasket Vellumoid 323810 323508 323568 18 Spring Bushing Brass --- --- 323579
JUNE 2016 Page 4 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
Testing and Maintenance
Reference NFPA 25, Standard for the Inspection, Testing andMaintenance of Water-Based Fire Protection Systems.
TESTING Before proceeding with any tests involving water flow, certain precautions need to be taken.1. Check the location where the test connection discharges to make sure that all is clear and that there is no possibility of the water flow causing damage or injury.
2. Check the end of the test connection to make sure that it is unobstructed. To obtain a satisfactory test, there must be an unrestricted flow of water when the test valve is wide open.
3. Check for alarm connections to a central station or fire department. If such connections are found, give proper no-tice to the signal receiving station before proceeding with the test.
Note: A main drain test will also operate local fire alarms - unless they are temporarily shut off.
Testing Alarm Valve and Waterflow Alarm Devices
NFPA 25 recommends that the alarm valve and its wa-terflow alarm devices be tested at least quarterly. The primary way to test this equipment is by opening the Inspectors Test Connection. This connection, generally located at the highest and most remote point on the sys-tem in relation to the alarm valve, consists of a test orifice and controlling globe valve. Opening of the globe valve (Inspectors Test Valve), and the subsequent discharge of water through the test orifice, simulates the operation of a sprinkler. Therefore, alarm devices should sound and/or operate when the Inspectors Test Valve is opened. An alternate means of testing waterflow alarm devices is to open the Alarm Test Valve provided as part of the alarm valve trim. It must be noted, however, that opening of this valve only tests the alarms; it does not test the operation of the alarm valve since the supply for the alarm test line is taken from a point below the alarm valve clapper (see respective trim drawings). This means of testing, therefore, should only be used when weather conditions or other cir-cumstances prohibit using the Inspectors Test Connection.
Note: If alarms connect to a central station or fire depart-ment, notify the signal receiving station when all tests have been completed.
NFPA 25 recommends that a water flow test be made quarterly from the main drain valve at the system riser. The purpose of this test is to show whether or not the normal water supply is available to the system. By comparing stat-ic and residual pressure readings with those previously es-tablished, a main drain test can indicate the possible pres-ence of closed valves or other obstructions in the supply piping. The procedure for conducting a Main Drain Test is as follows:
1. With the Main Drain Valve closed, note and record the reading on the lower Pressure Gauge at the Alarm Valve.
2. Open the Main Drain Valve slowly until it is wide open. Then, check to make sure that a full steady flow of water is discharging from the main drain pipe.
Note: If a full steady stream is not discharging, check the main drain piping further for possible obstructions.
3. Allow the water to flow until the reading on the lower Pressure Gauge drops and stabilizes. Then, record this reading.
Note: The first and higher pressure reading is the static pressure. The second, lower reading is the residual pres-sure with a given flow discharging from the main drain pipe.
4. Close the Main Drain Valve slowly.
Caution: If alarms have been temporarily shut off, they must be returned to service. If alarms connect to a central station or fire department, notify the signal receiving station when the test has been completed.
5. Compare both pressure readings with previously estab-lished or normal readings.
Note: If the readings compare favorably, the water sup-ply may be considered satisfactory. If, however, the pres-sure readings vary to any great extent, the condition should be investigated to determine the cause. Some possible causes are: Partially or totally closed system control valves. Clogged or frozen water mains. Serious leakage at valves or mains.
Flow Test at Main Drain Valve (Main Drain Test)
MAINTENANCE The Globe Alarm Check Valve and its related equip-ment should be examined periodically to ensure proper operation and trouble-free service. Several areas to be routinely inspected are:
Clapper Facing. The rubber clapper facing should be checked for wear or damage, and to determine that it is free of dirt and other foreign substances. If found to be worn or damaged (e.g., foreign matter imbedded in the surface), the facing should be replaced. If it is dirty, it should be cleaned, but compounds which could damage the rubber facing must never be used.
Seat Ring. The seat ring should be checked for nicks and for stones, dirt or other foreign matter lodged in the grooves or holes. It should be cleaned thoroughly. If the seat ring is found to be severely damaged, the complete alarm valve assembly should be replaced or returned to Globe for possible reconditioning.
By-Pass Check Valve. The ¾" check valve in the external by-pass should be checked for clapper and seat condition.
Retard Chamber. The outlet plug and drain plug assemblies should be checked for obstructions. The screens should be cleaned thoroughly.
Alarm Line Strainer. The ¾" stainer in the alarm line of the constant pressure trim setup should be checked and cleaned thoroughly.
Alarm Test Valve, Main Drain Valve & Inspectors Test Valve. All controlling valves which are normally closed when the alarm valve is in the set position should be checked to be sure that they are fully closed and not leaking.
Alarm Valve & Trim. The overall setup should be checked for visible leaks and possible physical damage to the valve and connections (e.g., broken gauges).
Resetting of System The Globe Alarm Check Valve is self-setting when testing procedures are followed. When sprinklers oper-ate, however, there are certain procedures which must be followed for restoring the system to service.
1. Close the System Control Valve (OS & Y, PIV or other).
Caution: In the event of a fire, the system control valve is to be closed only after it has been determined, posi-tively, that the fire has been extinguished.
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
2. Close the Alarm Control Valve.
3. Open the Main Drain Valve.
Note: It is necessary to drain the system only as required to allow for sprinkler replacement.
4. Replace the sprinklers which have operated.
5. Close the Main Drain Valve
6. Open the Inspectors Test Valve.
Note: This valve is opened to permit air to be vented from the system as it is being filled with water.
7. Slowly open the System Control Valve.
Caution: Open the valve only partially at the start of wa-ter flow into the system. Do not open it fully at this point. To do so may cause a water hammer to occur which could either damage the piping or trap large volumes of air within the system.
8. Continue filling the system until water discharges in a continuous stream from the Inspectors Test Connection.
9. Close the Inspectors Test Valve.
10. Turn the System Control Valve to its full open posi-tion, at the same time observing the Pressure Gauges.
Note: The system is filled when both gauges are steady and have the same pressure reading.
11. Conduct a Main Drain Test to make sure the water supply is satisfactory (see Flow Test at Main Drain Valve).
12. Open the Alarm Control Valve.
13. Conduct a test of the alarm devices (see Testing Alarm and Waterflow Alarm Devices).
14. Seal, lock, or otherwise secure the System Control Valve and Alarm Control Valve in an open position (per NFPA 25). The system is now ready for service.
15. If alarms connect to a central station or fire depart-ment, notify the signal receiving station that the system has been returned to service.
JUNE 2016 Page 5 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
175psi (12bars) RATED3" MODEL “H” SERIES VERTICAL POSITION / VARIABLE PRESSURE TRIM
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 6 23 1/2" x 3" Nipple 310304 1 70 1/2" Close Galv. Nipple 310300-G 6
3 1/2" Tee 311303 2 31 3 1/2" Water Gauge (0-300psi) 300119 2 73 1/2" x 2" Galv. Nipple 310302-G 1
4 1/2" Close Nipple 310300 10 33 1/2" x 3 1/2" Nipple 310305 1 74 1/2" x 7 1/2" Galv. Nipple 310313-G 1
5 1/2" Ball Valve 311692 2 37 1/2" x 1 1/2" Nipple 310301 1 83 1 1/2" Angle Valve 311616 1
15 1/4" 3-Way Valve 311683 2 46 1/2" x 4" Nipple 310306 1 86 1 1/2" x 1 1/2" x 1/2" Tee 311391 1
16 1/4" Plug 311001 3 59 Retard Chamber 323350 1 102 1/4" x 1 1/2" Nipple 310101 1
19 1/2" x 2" Nipple 310302 1 64 1/4" x 4" Nipple 310106 1 106 1 1/2" x 3 1/2" Nipple 310704 1
20 1/2" Swing Check Valve 311639 2 67 1/2" x 1/4" x 1/2" Tee 311305 3 111 1 1/2" x 2 1/2" Nipple 310702 1
21 1/2" Union 311403 4
JUNE 2016 Page 6 BULLETIN A.C.V.I.M., REV. #14
59
37
67 16
23
1
420
4
21
486
111
83
106
1
73
70
21
70
119
2121
4
4
46
74
67
64
4
67
1
1024
20
4
15
15
16
1631
31
1
33
3
4
5
4
70
3
70
170
5
70
VALVE ONLYMODEL "H-1" 323800MODEL "H-2" 323825MODEL "H-3" 323801
TRIM ONLY323769
VALVE FACTORY TRIMMEDMODEL "H-1" 323757MODEL "H-2" 323761MODEL "H-3" 323765
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
300psi (20bars) RATED3" MODEL “H-2” VERTICAL POSITION / VARIABLE PRESSURE TRIM
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 6 23 1/2" x 3" Nipple 310304 1 70 1/2" Close Galv. Nipple 310300-G 6
3 1/2" Tee 311303 2 31 3 1/2" Water Gauge (0-300psi) 300119 2 73 1/2" x 2" Galv. Nipple 310302-G 1
4 1/2" Close Nipple 310300 10 33 1/2" x 3 1/2" Nipple 310305 1 74 1/2" x 7 1/2" Galv. Nipple 310313-G 1
5 1/2" Ball Valve 311692 2 37 1/2" x 1 1/2" Nipple 310301 1 83 1 1/2" Angle Valve 311616 1
15 1/4" 3-Way Valve 311683 2 46 1/2" x 4" Nipple 310306 1 86 1 1/2" x 1 1/2" x 1/2" Tee 311391 1
16 1/4" Plug 311001 3 59 Retard Chamber 323350 1 102 1/4" x 1 1/2" Nipple 310101 1
19 1/2" x 2" Nipple 310302 1 64 1/4" x 4" Nipple 310106 1 106 1 1/2" x 3 1/2" Nipple 310704 1
20 1/2" Swing Check Valve 311639 2 67 1/2" x 1/4" x 1/2" Tee 311305 3 111 1 1/2" x 2 1/2" Nipple 310702 1
21 1/2" Union 311403 4
31
1631
16
15
15102
67
464
2121
4
19
4
67
4 20
4
74
1
17021
106
73
1 7083
111
86
4
21
4
20
4
1
23
67 16
37
59
46
33
3
4
5
4
1
70
3
70
1
705
70
VALVE ONLYMODEL "H-2" 323825-HP
TRIM ONLY323769-HP
VALVE FACTORY TRIMMEDMODEL "H-2" 323761-HP
JUNE 2016 Page 7 BULLETIN A.C.V.I.M., REV. #14
175psi (12bars) RATED3" MODEL “H” SERIES VERTICAL POSITION / CONSTANT PRESSURE TRIM
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 6 31 3 1/2" Water Gauge (0-300psi) 300119 2 73 1/2" x 2" Galv. Nipple 310302-G 1
3 1/2" Tee 311303 2 32 1/2" Coupling 311423 1 74 1/2" x 7 1/2" Galv. Nipple 310313-G 1
4 1/2" Close Nipple 310300 11 33 1/2" x 3 1/2" Nipple 310305 1 83 1 1/2" Angle Valve 311616 1
5 1/2" Ball Valve 311692 2 35 Alarm Line Bleeder 320506 1 86 1 1/2" x 1 1/2" x 1/2" Tee 311391 1
15 1/4" 3-Way Valve 311683 2 36 3/4" Strainer 325535 1 88 1/2" x 10" Nipple 310320 1
16 1/4" Plug 311001 3 46 1/2" x 4" Nipple 310306 1 101 1 1/2" Close Nipple 310700 1
19 1/2" x 2" Nipple 310302 1 64 1/4" x 4" Nipple 310106 1 102 1/4" x 1 1/2" Nipple 310101 1
20 1/2" Swing Check Valve 311639 2 67 1/2" x 1/4" x 1/2" Tee 311305 3 103 3/4" Close Galv. Nipple 310400-G 1
21 1/2" Union 311403 4 70 1/2" Close Galv. Nipple 310300-G 6 106 1 1/2" x 3 1/2" Nipple 310704 1
30 3/4" x 1/2" x 1/2" Tee 311318 1
JUNE 2016 Page 8 BULLETIN A.C.V.I.M., REV. #14
88
32
35
10336
30
70
5
701
7070
3
4
5
4
3
33
146
4
20
4
1
67
102
64
15
16
3131
16
15
4
21
4
19
21
467
74
1
7021
70
1
73
106
83
101
864
214
20 4
14
6716
VALVE ONLYMODEL "H-1" 323800MODEL "H-2" 323825MODEL "H-3" 323801
TRIM ONLY323770
VALVE FACTORY TRIMMEDMODEL "H-1" 323758MODEL "H-2" 323762MODEL "H-3" 323766
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
300psi (20bars) RATED3" MODEL “H-2” VERTICAL POSITION / CONSTANT PRESSURE TRIM
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 6 31 3 1/2" Water Gauge (0-300psi) 300119 2 73 1/2" x 2" Galv. Nipple 310302-G 1
3 1/2" Tee 311303 2 32 1/2" Coupling 311423 1 74 1/2" x 7 1/2" Galv. Nipple 310313-G 1
4 1/2" Close Nipple 310300 11 33 1/2" x 3 1/2" Nipple 310305 1 83 1 1/2" Angle Valve 311616 1
5 1/2" Ball Valve 311692 2 35 Alarm Line Bleeder 320506 1 86 1 1/2" x 1 1/2" x 1/2" Tee 311391 1
15 1/4" 3-Way Valve 311683 2 36 3/4" Strainer 325535 1 88 1/2" x 10" Nipple 310320 1
16 1/4" Plug 311001 3 46 1/2" x 4" Nipple 310306 1 101 1 1/2" Close Nipple 310700 1
19 1/2" x 2" Nipple 310302 1 64 1/4" x 4" Nipple 310106 1 102 1/4" x 1 1/2" Nipple 310101 1
20 1/2" Swing Check Valve 311639 2 67 1/2" x 1/4" x 1/2" Tee 311305 3 103 3/4" Close Galv. Nipple 310400-G 1
21 1/2" Union 311403 4 70 1/2" Close Galv. Nipple 310300-G 6 106 1 1/2" x 3 1/2" Nipple 310704 1
30 3/4" x 1/2" x 1/2" Tee 311318 1
31
1631
16
15
15
102
6767
64
4
2121
4
19
4
74
1
146
7021
70
1
73
106
83
101
864
21
4
20
4
1
4
6716
88
32
35
36103
30
70
33
3
4
5
4
3
70
170
5
70
1
20
4
4
VALVE ONLYMODEL "H-2" 323825-HP
TRIM ONLY323770-HP
VALVE FACTORY TRIMMED323762-HP
JUNE 2016 Page 9 BULLETIN A.C.V.I.M., REV. #14
175psi (12bars) RATED3" MODEL “H” SERIES HORIZONTAL POSITION / VARIABLE PRESSURE TRIM
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
JUNE 2016 Page 10 BULLETIN A.C.V.I.M., REV. #14
110
83 163
1
70
5
70
59
4
16
67
23
1
4
20
4
21
4
86
107
1
70
3
4
1
74
5
4
3
33
1
4
20
4
23
67
1
704
21 21
70
4
73
1
19
21
42
4
67
109
15
15
16
31
31
16
70
VALVE ONLYMODEL "H-1" 323800MODEL "H-2" 323825MODEL "H-3" 323801
TRIM ONLY323767
VALVE FACTORY TRIMMEDMODEL "H-1" 323755MODEL "H-2" 323759MODEL "H-3" 323763
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 7 21 1/2" Union 311403 4 73 1/2" x 2" Galv. Nipple 310302-G 1
3 1/2" Tee 311303 2 23 1/2" x 3" Nipple 310304 2 74 1/2" x 7 1/2" Galv. Nipple 310313-G 1
4 1/2" Close Nipple 310300 11 31 3 1/2" Water Gauge (0-300psi) 300119 2 83 1 1/2" Angle Valve 311616 1
5 1/2" Ball Valve 311692 2 33 1/2" x 3 1/2" Nipple 310305 1 86 1 1/2" x 1 1/2" x 1/2" Tee 311391 1
15 1/4" 3-Way Valve 311683 2 42 1/4" x 6" Nipple 310110 1 107 1 1/2" x 4 1/2" Nipple 310706 1
16 1/4" Plug 311001 3 59 Retard Chamber 323350 1 109 1/4" x 3 1/2" Nipple 310105 1
19 1/2" x 2" Nipple 310302 1 67 1/2" x 1/4" x 1/2" Tee 311305 3 110 1 1/2" x 8" Nipple 310715 1
20 1/2" Swing Check Valve 311639 2 70 1/2" Close Galv. Nipple 310300-G 6 163 1/2" x 12 1/2" Galv. Nipple 310338-G 1
JUNE 2016 Page 11 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
300psi (20bars) RATED3" MODEL “H-2” HORIZONTAL POSITION / VARIABLE PRESSURE TRIM
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 7 21 1/2" Union 311403 4 73 1/2" x 2" Galv. Nipple 310302-G 1
3 1/2" Tee 311303 2 23 1/2" x 3" Nipple 310304 2 74 1/2" x 7 1/2" Galv. Nipple 310313-G 1
4 1/2" Close Nipple 310300 11 31 3 1/2" Water Gauge (0-300psi) 300119 2 83 1 1/2" Angle Valve 311616 1
5 1/2" Ball Valve 311692 2 33 1/2" x 3 1/2" Nipple 310305 1 86 1 1/2" x 1 1/2" x 1/2" Tee 311391 1
15 1/4" 3-Way Valve 311683 2 42 1/4" x 6" Nipple 310110 1 107 1 1/2" x 4 1/2" Nipple 310706 1
16 1/4" Plug 311001 3 59 Retard Chamber 323350 1 109 1/4" x 3 1/2" Nipple 310105 1
19 1/2" x 2" Nipple 310302 1 67 1/2" x 1/4" x 1/2" Tee 311305 3 110 1 1/2" x 8" Nipple 310715 1
20 1/2" Swing Check Valve 311639 2 70 1/2" Close Galv. Nipple 310300-G 6 163 1/2" x 12 1/2" Galv. Nipple 310338-G 1
110
83 163
1
70
5
70
59
4
16
67
23
1
4
20
4
21
4
86
107
1
70
3
4
1
74
5
4
3
33
1
4
20
4
23
67
1
704
21 21
70
4
73
1
19
21
42
4
67
109
15
15
16
31
31
16
70
VALVE ONLYMODEL "H-2" 323825-HP
TRIM ONLY323767-HP
VALVE FACTORY TRIMMEDMODEL "H-2" 323759-HP
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
175psi (12bars) RATED3" MODEL “H” SERIES HORIZONTAL POSITION / CONSTANT PRESSURE TRIM
JUNE 2016 Page 12 BULLETIN A.C.V.I.M., REV. #14
108
83
1667
70
5
70
30
103
36
35
32
37
204
21
4
86
107
73
3
70
1
4
5
74
4
3
33
1
46
4
1
20
4
70
21
70
1
734
2121
4
6767
42
109
4
15
31
1631
16
15
19
VALVE ONLYMODEL "H-1" 323800MODEL "H-2" 323825MODEL "H-3" 323801
TRIM ONLY323768
VALVE FACTORY TRIMMEDMODEL "H-1" 323756MODEL "H-2" 323760MODEL "H-3" 323764
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 4 31 3 1/2" Water Gauge (0-300psi) 300119 2 70 1/2" Close Galv. Nipple 310300-G 5
3 1/2" Tee 311303 2 32 1/2" Coupling 311423 1 73 1/2" x 2" Galv. Nipple 310302-G 2
4 1/2" Close Nipple 310300 9 33 1/2" x 3 1/2" Nipple 310305 1 74 1/2" x 7 1/2" Galv. Nipple 310313-G 1
5 1/2" Ball Valve 311692 2 35 Alarm Line Bleeder 320506 1 83 1 1/2" Angle Valve 311616 1
15 1/4" 3-Way Valve 311683 2 36 3/4" Strainer 325535 1 86 1 1/2" x 1 1/2" x 1/2" Tee 311391 1
16 1/4" Plug 311001 3 37 1/2" x 1 1/2" Nipple 310301 1 103 3/4" Close Galv. Nipple 310400-G 1
19 1/2" x 2" Nipple 310302 1 42 1/4" x 6" Nipple 310110 1 107 1 1/2" x 4 1/2" Nipple 310706 1
20 1/2" Swing Check Valve 311639 2 46 1/2" x 4" Nipple 310306 1 108 1 1/2" x 6" Nipple 310709 1
21 1/2" Union 311403 4 67 1/2" x 1/4" x 1/2" Tee 311305 3 109 1/4" x 3 1/2" Nipple 310105 1
30 3/4" x 1/2" x 1/2" Tee 311318 1
JUNE 2016 Page 13 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
300psi (20bars) RATED3" MODEL “H-2” HORIZONTAL POSITION / CONSTANT PRESSURE TRIM
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 4 31 3 1/2" Water Gauge (0-300psi) 300119 2 70 1/2" Close Galv. Nipple 310300-G 5
3 1/2" Tee 311303 2 32 1/2" Coupling 311423 1 73 1/2" x 2" Galv. Nipple 310302-G 2
4 1/2" Close Nipple 310300 9 33 1/2" x 3 1/2" Nipple 310305 1 74 1/2" x 7 1/2" Galv. Nipple 310313-G 1
5 1/2" Ball Valve 311692 2 35 Alarm Line Bleeder 320506 1 83 1 1/2" Angle Valve 311616 1
15 1/4" 3-Way Valve 311683 2 36 3/4" Strainer 325535 1 86 1 1/2" x 1 1/2" x 1/2" Tee 311391 1
16 1/4" Plug 311001 3 37 1/2" x 1 1/2" Nipple 310301 1 103 3/4" Close Galv. Nipple 310400-G 1
19 1/2" x 2" Nipple 310302 1 42 1/4" x 6" Nipple 310110 1 107 1 1/2" x 4 1/2" Nipple 310706 1
20 1/2" Swing Check Valve 311639 2 46 1/2" x 4" Nipple 310306 1 108 1 1/2" x 6" Nipple 310709 1
21 1/2" Union 311403 4 67 1/2" x 1/4" x 1/2" Tee 311305 3 109 1/4" x 3 1/2" Nipple 310105 1
30 3/4" x 1/2" x 1/2" Tee 311318 1
108
83
1667
70
5
70
30
103
36
35
32
37
204
21
4
86
107
73
3
70
1
4
5
74
4
3
33
1
46
4
1
20
4
70
21
70
1
734
2121
4
6767
42
109
4
15
31
1631
16
15
19
VALVE ONLYMODEL "H-2" 323825-HP
TRIM ONLY323768-HP
VALVE FACTORY TRIMMED323760-HP
JUNE 2016 Page 14 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
175psi (12bars) RATED4" MODEL “H” SERIES VERTICAL POSITION / VARIABLE PRESSURE TRIM
59
70
5
70
1
71
3
37
71
1
5
37
6
7
8
24
12
13
12
6
74
12
12238
15
122
612
17
17
41
18
45
15
16
31 16
31
702171
1
25
22
22
27
4 2119
20 4 67
16
98VALVE ONLYMODEL "H-1" 323500MODEL "H-2" 323550MODEL "H-3" 323540
TRIM ONLY323530
VALVE FACTORY TRIMMEDMODEL "H-1" 323525MODEL "H-2" 323555MODEL "H-3" 323545
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 3 17 3/4" Union 311404 2 38 1/4" x 2" Nipple 310103 1
3 1/2" Tee 311303 1 18 3/4" x 2 1/2" Nipple 310402 1 41 3/4" x 1 1/2" Nipple 310413 1
4 1/2" Close Nipple 310300 2 19 1/2" x 2" Nipple 310302 1 45 1/4" x 5" Nipple 310108 1
5 1/2" Ball Valve 311692 2 20 1/2" Swing Check Valve 311639 1 59 Retard Chamber 323350 1
6 3/4" x 1/2" x 3/4" Tee 311313 3 21 1/2" Union 311403 2 67 1/2" x 1/4" x1/2" Tee 311305 1
7 3/4" x 3" Nipple 310403 1 22 2" x 3" Nipple 310802 2 70 1/2" Close Galv. Nipple 310300-G 3
8 3/4" Elbow 311204 1 24 3/4" x 4 1/2" Nipple 310406 1 71 1/2" x 1 1/2" Galv. Nipple 310301-G 3
12 3/4" Close Nipple 310400 4 25 2" Angle Valve 311617 1 74 1/2" x 8 1/2" Galv. Nipple 310316-G 1
13 3/4" Swing Check Valve 311640 1 27 2" x 2" x 1/2" Tee 311380 1 98 1/2" x 4 1/2" Nipple 310307 1
15 1/4" 3-Way Valve 311683 2 31 3 1/2" Water Gauge (0-300psi) 300119 2 122 1/2" x 1/4" Reducing Bushing 311100 2
16 1/4" Plug 311001 3 37 1/2" x 1 1/2" Nipple 310301 2
JUNE 2016 Page 15 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
300psi (20bars) RATED4" MODEL “H-2” VERTICAL POSITION / VARIABLE PRESSURE TRIM
59
70
5
70
1
71
3
37
71
1
5
37
6
7
8
24
12
13
12
6
74
12
12238
15
122
612
17
159
41
18
45
15
16
31 16
31
702171
1
25
22
22
27
4 2119
20 4 67
16
98VALVE ONLYMODEL "H-2" 323550-HP
TRIM ONLY323530-HP
VALVE FACTORY TRIMMEDMODEL "H-2" 323555-HP
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 3 17 3/4" Union 311404 1 38 1/4" x 2" Nipple 310103 1
3 1/2" Tee 311303 1 18 3/4" x 2 1/2" Nipple 310402 1 41 3/4" x 1 1/2" Nipple 310413 1
4 1/2" Close Nipple 310300 2 19 1/2" x 2" Nipple 310302 1 45 1/4" x 5" Nipple 310108 1
5 1/2" Ball Valve 311692 2 20 1/2" Swing Check Valve 311639 1 59 Retard Chamber 323350 1
6 3/4" x 1/2" x 3/4" Tee 311313 3 21 1/2" Union 311403 2 67 1/2" x 1/4" x 1/2" Tee 311305 1
7 3/4" x 3" Nipple 310403 1 22 2" x 3" Nipple 310802 2 70 1/2" Close Galv. Nipple 310300-G 3
8 3/4" Elbow 311204 1 24 3/4" x 4 1/2" Nipple 310406 1 71 1/2" x 1 1/2" Galv. Nipple 310301-G 3
12 3/4" Close Nipple 310400 4 25 2" Angle Valve 311617 1 74 1/2" x 8 1/2" Galv. Nipple 310316-G 1
13 3/4" Swing Check Valve 311640 1 27 2" x 2" x 1/2" Tee 311380 1 98 1/2" x 4 1/2" Nipple 310307 1
15 1/4" 3-Way Valve 311683 2 31 3 1/2" Water Gauge (0-300psi) 300119 2 122 1/2" x 1/4" Reducing Bushing 311100 2
16 1/4" Plug 311001 3 37 1/2" x 1 1/2" Nipple 310301 2 159 ø.437 Restricted Orifice Union 311410 1
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
175psi (12bars) RATED4" MODEL “H” SERIES VERTICAL POSITION / CONSTANT PRESSURE TRIM
31 1631
1516
15
45
38
122
12
35
6
122
1
13
12
6
24
34
74
1
17
18
17
41
702171
2225
58
274
214
204
67
16
70
8
32
37
7
6
12
71 3
70
12
1
5
5
103
30
70
3637
VALVE ONLYMODEL "H-1" 323500MODEL "H-2" 323550MODEL "H-3" 323540
TRIM ONLY323531
VALVE FACTORY TRIMMEDMODEL "H-1" 323526MODEL "H-2" 323556MODEL "H-3" 323546
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 3 18 3/4" x 2 1/2" Nipple 310402 1 36 3/4" Strainer 325535 1
3 1/2" Tee 311303 1 20 1/2" Swing Check Valve 311639 1 37 1/2" x 1 1/2" Nipple 310301 2
4 1/2" Close Nipple 310300 3 21 1/2" Union 311403 2 38 1/4" x 2" Nipple 310102 1
5 1/2" Ball Valve 311692 2 22 2" x 3" Nipple 310802 1 41 3/4" x 1 1/2" Nipple 310413 1
6 3/4" x 1/2" x 3/4" Tee 311313 3 24 3/4" x 4 1/2" Nipple 310406 1 45 1/4" x 5" Nipple 310108 1
7 3/4" x 3" Nipple 310403 1 25 2" Angle Valve 311617 1 58 2" x 2 1/2" Nipple 310801 1
8 3/4" Elbow 311204 1 27 2" x 2" x 1/2" Tee 311380 1 67 1/2" x 1/4" x 1/2" Tee 311305 1
12 3/4" Close Nipple 310400 4 30 3/4" x 1/2" x 1/2" Tee 311318 1 70 1/2" Close Galv. Nipple 310300-G 4
13 3/4" Swing Check Valve 311640 1 31 3 1/2" Water Gauge (0-300psi) 300119 2 71 1/2" x 1 1/2" Galv. Nipple 310301-G 2
15 1/4" 3-Way Valve 311683 2 32 1/2" Coupling 311423 1 74 1/2" x 8 1/2" Galv. Nipple 310316-G 1
16 1/4" Plug 311001 3 34 1/2" x 12" Nipple 310318 1 103 3/4" Close Galv. Nipple 310400-G 1
17 3/4" Union 311404 2 35 Alarm Line Bleeder 320506 1 122 1/2" x 1/4" Reducing Bushing 311100 2
JUNE 2016 Page 16 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
300psi (20bars) RATED4" MODEL “H-2” VERTICAL POSITION / CONSTANT PRESSURE TRIM
31 1631
1516
15
45
38
122
12
35
6
122
1
13
12
6
24
34
74
1
17
18
159
41
702171
2225
58
274
214
204
67
16
70
8
32
37
7
6
12
71 3
70
12
1
5
5
103
30
70
3637
VALVE ONLYMODEL "H-2" 323550-HP
TRIM ONLY323531-HP
VALVE FACTORY TRIMMEDMODEL "H-2" 323556-HP
JUNE 2016 Page 17 BULLETIN A.C.V.I.M., REV. #14
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 3 20 1/2" Swing Check Valve 311639 1 37 1/2" x 1 1/2" Nipple 310301 2
3 1/2" Tee 311303 1 21 1/2" Union 311403 2 38 1/4" x 2" Nipple 310102 1
4 1/2" Close Nipple 310300 3 22 2" x 3" Nipple 310802 1 41 3/4" x 1 1/2" Nipple 310413 1
5 1/2" Ball Valve 311692 2 24 3/4" x 4 1/2" Nipple 310406 1 45 1/4" x 5" Nipple 310108 1
6 3/4" x 1/2" x 3/4" Tee 311313 3 25 2" Angle Valve 311617 1 58 2" x 2 1/2" Nipple 310801 1
7 3/4" x 3" Nipple 310403 1 27 2" x 2" x 1/2" Tee 311380 1 67 1/2" x 1/4" x 1/2" Tee 311305 1
8 3/4" Elbow 311204 1 30 3/4" x 1/2" x 1/2" Tee 311318 1 70 1/2" Close Galv. Nipple 310300-G 4
12 3/4" Close Nipple 310400 4 31 3 1/2" Water Gauge (0-300psi) 300119 2 71 1/2" x 1 1/2" Galv. Nipple 310301-G 2
13 3/4" Swing Check Valve 311640 1 32 1/2" Coupling 311423 1 74 1/2" x 8 1/2" Galv. Nipple 310316-G 1
15 1/4" 3-Way Valve 311683 2 34 1/2" x 12" Nipple 310318 1 103 3/4" Close Galv. Nipple 310400-G 1
16 1/4" Plug 311001 3 35 Alarm Line Bleeder 320506 1 122 1/2" x 1/4" Reducing Bushing 311100 2
17 3/4" Union 311404 1 36 3/4" Strainer 325535 1 159 ø.437 Restricted Orifice Union 311410 1
18 3/4" x 2 1/2" Nipple 310402 1
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
175psi (12bars) RATED4" MODEL “H” SERIES HORIZONTAL POSITION / VARIABLE PRESSURE TRIM
JUNE 2016 Page 18 BULLETIN A.C.V.I.M., REV. #14
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 4 18 3/4" x 2 1/2" Nipple 310402 1 41 3/4" x 1 1/2" Nipple 310413 1
3 1/2" Tee 311303 1 20 1/2" Swing Check Valve 311639 1 42 1/4" x 6" Nipple 310110 2
4 1/2" Close Nipple 310300 1 21 1/2" Union 311403 2 59 Retard Chamber 323350 1
5 1/2" Ball Valve 311692 2 24 3/4" x 4 1/2" Nipple 310406 1 60 1/4" Coupling 311402 1
6 3/4" x 1/2" x 3/4" Tee 311313 3 25 2" Angle Valve 311617 1 67 1/2" x 1/4" x 1/2" Tee 311305 1
7 3/4" x 3" Nipple 310403 1 26 2" x 5" Nipple 310803 1 68 2" x 7 1/2" Nipple 310809 1
8 3/4" Elbow 311204 1 27 2" x 2" x 1/2" Tee 311380 1 70 1/2" Close Galv. Nipple 310300-G 3
11 1/4" x 6 1/2" Nipple 310115 2 28 1/4" Elbow 311201 2 71 1/2" x 1 1/2" Galv. Nipple 310301-G 2
12 3/4" Close Nipple 310400 4 29 1/4" x 10" Nipple 310136 1 72 1/2" x 2 1/2" Galv. Nipple 310303-G 1
13 3/4" Swing Check Valve 311640 1 31 3 1/2" Water Gauge (0-300psi) 300119 2 74 1/2" x 8 1/2" Galv. Nipple 310316-G 1
15 1/4" 3-Way Valve 311683 2 37 1/2" x 1 1/2" Nipple 310301 2 75 1/2" x 12" Galv. Nipple 310318-G 1
16 1/4" Plug 311001 3 39 1/2" x 2 1/2" Nipple 310303 3 122 1/2" x 1/4" Reducing Bushing 311100 2
17 3/4" Union 311404 2
16
31
31
15
42
16
15
2960
42
2828
1111
122
122
12
17
6
24
6
12
17
1821
7141
70
1
74
1
71
68
75
25
1
72
3
37
5
37
6
7
8
13
12
12
26
3927
21
39
20
39
67
16
4
59
70
5
70
1VALVE ONLY
MODEL "H-1" 323500MODEL "H-2" 323550MODEL "H-3" 323540
TRIM ONLY323535
VALVE FACTORY TRIMMEDMODEL "H-1" 323527MODEL "H-2" 323627MODEL "H-3" 323538
JUNE 2016 Page 19 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
300psi (20bars) RATED4" MODEL “H-2” HORIZONTAL POSITION / VARIABLE PRESSURE TRIM
16
31
31
15
42
16
15
2960
42
2828
1111
122
122
12
17
6
24
6
12
159
1821
7141
70
1
74
1
71
68
75
25
1
72
3
37
5
37
6
7
8
13
12
12
26
3927
21
39
20
39
67
16
4
59
70
5
70
1
VALVE ONLYMODEL "H-2" 323550-HP
TRIM ONLY323535-HP
VALVE FACTORY TRIMMEDMODEL "H-2" 323627-HP
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 4 18 3/4" x 2 1/2" Nipple 310402 1 42 1/4" x 6" Nipple 310110 2
3 1/2" Tee 311303 1 20 1/2" Swing Check Valve 311639 1 59 Retard Chamber 323350 1
4 1/2" Close Nipple 310300 1 21 1/2" Union 311403 2 60 1/4" Coupling 311402 1
5 1/2" Ball Valve 311692 2 24 3/4" x 4 1/2" Nipple 310406 1 67 1/2" x 1/4" x 1/2" Tee 311305 1
6 3/4" x 1/2" x 3/4" Tee 311313 3 25 2" Angle Valve 311617 1 68 2" x 7 1/2" Nipple 310809 1
7 3/4" x 3" Nipple 310403 1 26 2" x 5" Nipple 310803 1 70 1/2" Close Galv. Nipple 310300-G 3
8 3/4" Elbow 311204 1 27 2" x 2" x 1/2" Tee 311380 1 71 1/2" x 1 1/2" Galv. Nipple 310301-G 2
11 1/4" x 6 1/2" Nipple 310115 2 28 1/4" Elbow 311201 2 72 1/2" x 2 1/2" Galv. Nipple 310303-G 1
12 3/4" Close Nipple 310400 4 29 1/4" x 10" Nipple 310136 1 74 1/2" x 8 1/2" Galv. Nipple 310316-G 1
13 3/4" Swing Check Valve 311640 1 31 3 1/2" Water Gauge (0-300psi) 300119 2 75 1/2" x 12" Galv. Nipple 310318-G 1
15 1/4" 3-Way Valve 311683 2 37 1/2" x 1 1/2" Nipple 310301 2 122 1/2" x 1/4" Reducing Bushing 311100 2
16 1/4" Plug 311001 3 39 1/2" x 2 1/2" Nipple 310303 3 159 ø.437 Restricted Orifice 311410 1
17 3/4" Union 311404 1 41 3/4" x 1 1/2" Nipple 310413 1
JUNE 2016 Page 20 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
175psi (12bars) RATED4" MODEL “H” SERIES HORIZONTAL POSITION / CONSTANT PRESSURE TRIM
31
1615
4231
16
29
60
42
2828
1111
41
17
122
122
66
12
24
12 13
12
7
8
6
37
5
37
17
1870
21
71
1
74 69
25
1
71
3
73
16
705
70
30103
36
35
32
37
20
3721
3726
27
12
67
15
VALVE ONLYMODEL "H-1" 323500MODEL "H-2" 323550MODEL "H-3" 323540
TRIM ONLY323536
VALVE FACTORY TRIMMEDMODEL "H-1" 323529MODEL "H-2" 323628MODEL "H-3" 323539
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 2 20 1/2" Swing Check Valve 311639 1 37 1/2" x 1 1/2" Nipple 310301 5
3 1/2" Tee 311303 1 21 1/2" Union 311403 2 41 3/4" x 1 1/2" Nipple 310413 1
5 1/2" Ball Valve 311692 2 24 3/4" x 4 1/2" Nipple 310406 1 42 1/4" x 6" Nipple 310110 2
6 3/4" x 1/2" x 3/4" Tee 311313 3 25 2" Angle Valve 311617 1 60 1/4" Coupling 311402 1
7 3/4" x 3" Nipple 310403 1 26 2" x 5" Nipple 310803 1 67 1/2" x 1/4" x 1/2" Tee 311305 1
8 3/4" Elbow 311204 1 27 2" x 2" x 1/2" Tee 311380 1 69 2" x 6" Nipple 310808 1
11 1/4" x 6 1/2" Nipple 310115 2 28 1/4" Elbow 311201 2 70 1/2" Close Galv. Nipple 310300-G 3
12 3/4" Close Nipple 310400 4 29 1/4" x 10" Nipple 310136 1 71 1/2" x 1 1/2" Galv. Nipple 310301-G 2
13 3/4" Swing Check Valve 311640 1 30 3/4" x 1/2" x 1/2" Tee 311318 1 73 1/2" x 2" Galv. Nipple 310302-G 1
15 1/4" 3-Way Valve 311683 2 31 3 1/2" Water Gauge (0-300psi) 300119 2 74 1/2" x 8 1/2" Galv. Nipple 310316-G 1
16 1/4" Plug 311001 3 32 1/2" Coupling 311423 1 103 3/4" Close Galv. Nipple 310400-G 1
17 3/4" Union 311404 2 35 Alarm Line Bleeder 320506 1 122 1/2" x 1/4" Reducing Bushing 311100 2
18 3/4" x 2 1/2" Nipple 310402 1 36 3/4" Strainer 325535 1
JUNE 2016 Page 21 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
300psi (20bars) RATED4" MODEL “H-2” HORIZONTAL POSITION / CONSTANT PRESSURE TRIM
31
16
15
4231
16
29
60
42
2828
1111
18
17
122
122
66
12
24
12 13
12
7
8
6
37
5
37
159
41
70
21
71
1
7469
25
1
71
3
73
16
705
70
30103
36
35
32
37
20
3721
3726
27
12
67
15
VALVE ONLYMODEL "H-2" 323550-HP
TRIM ONLY323536-HP
VALVE FACTORY TRIMMEDMODEL "H-2" 323628-HP
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 2 20 1/2" Swing Check Valve 311639 1 37 1/2" x 1 1/2" Nipple 310301 5
3 1/2" Tee 311303 1 21 1/2" Union 311403 2 41 3/4" x 1 1/2" Nipple 310413 1
5 1/2" Ball Valve 311692 2 24 3/4" x 4 1/2" Nipple 310406 1 42 1/4" x 6" Nipple 310110 2
6 3/4" x 1/2" x 3/4" Tee 311313 3 25 2" Angle Valve 311617 1 60 1/4" Coupling 311402 1
7 3/4" x 3" Nipple 310403 1 26 2" x 5" Nipple 310803 1 67 1/2" x 1/4" x 1/2" Tee 311305 1
8 3/4" Elbow 311204 1 27 2" x 2" x 1/2" Tee 311380 1 69 2" x 6" Nipple 310808 1
11 1/4" x 6 1/2" Nipple 310115 2 28 1/4" Elbow 311201 2 70 1/2" Close Galv. Nipple 310300-G 3
12 3/4" Close Nipple 310400 4 29 1/4" x 10" Nipple 310136 1 71 1/2" x 1 1/2" Galv. Nipple 310301-G 2
13 3/4" Swing Check Valve 311640 1 30 3/4" x 1/2" x 1/2" Tee 311318 1 73 1/2" x 2" Galv. Nipple 310302-G 1
15 1/4" 3-Way Valve 311683 2 31 3 1/2" Water Gauge (0-300psi) 300119 2 74 1/2" x 8 1/2" Galv. Nipple 310316-G 1
16 1/4" Plug 311001 3 32 1/2" Coupling 311423 1 103 3/4" Close Galv. Nipple 310400-G 1
17 3/4" Union 311404 1 35 Alarm Line Bleeder 320506 1 122 1/2" x 1/4" Reducing Bushing 311100 2
18 3/4" x 2 1/2" Nipple 310402 1 36 3/4" Strainer 325535 1 159 ø.437 Restricted Orifice Union 311410 1
JUNE 2016 Page 22 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
175psi (12bars) RATED6" MODEL “H” SERIES VERTICAL POSITION / VARIABLE PRESSURE TRIM
70
5
70
59
98
16
67
42019
214
27
22
25
22
7121 70
1
1817
12
74
8
24
6
1
43
6
41
17
12
45
16
15
3116
31
15
38
6
12
13
12
4
5
37
73
371
122
122
1
VALVE ONLYMODEL "H-1" 323560
MODEL "H-2" 323667 (ANSI)MODEL "H-2" 323667-D (DIN)
MODEL "H-3" 323590
TRIM ONLY323580
VALVE FACTORY TRIMMEDMODEL "H-1" 323575
MODEL "H-2" 323792 (ANSI)MODEL "H-2" 323792-D (DIN)
MODEL "H-3" 323595
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 3 18 3/4" x 2 1/2" Nipple 310402 1 41 3/4" x 1 1/2" Nipple 310413 1
3 1/2" Tee 311303 1 19 1/2" x 2" Nipple 310302 1 43 3/4" x 3 1/2" Nipple 310404 1
4 1/2" Close Nipple 310300 3 20 1/2" Swing Check Valve 311639 1 45 1/4" x 5" Nipple 310108 1
5 1/2" Ball Valve 311692 2 21 1/2" Union 311403 2 59 Retard Chamber 323350 1
6 3/4" x 1/2" x 3/4" Tee 311313 3 22 2" x 3" Nipple 310802 2 67 1/2" x 1/4" x 1/2" Tee 311305 1
8 3/4" Elbow 311204 1 24 3/4" x 4 1/2" Nipple 310406 1 70 1/2" Close Galv. Nipple 310300-G 3
12 3/4" Close Nipple 310400 4 25 2" Angle Valve 311617 1 71 1/2" x 1 1/2" Galv. Nipple 310301-G 2
13 3/4" Swing Check Valve 311640 1 27 2" x 2" x 1/2" Tee 311380 1 73 1/2" x 2" Galv. Nipple 310302-G 1
15 1/4" 3-Way Valve 311683 2 31 3 1/2" Water Gauge (0-300psi) 300119 2 74 1/2" x 8 1/2" Galv. Nipple 310316-G 1
16 1/4" Plug 311001 3 37 1/2" x 1 1/2" Nipple 310301 1 98 1/2" x 4 1/2" Nipple 310307 1
17 3/4" Union 311404 2 38 1/4" x 2" Nipple 310102 1 122 1/2" x 1/4" Reducing Bushing 311100 2
JUNE 2016 Page 23 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
300psi (20bars) RATED6" MODEL “H-2” VERTICAL POSITION / VARIABLE PRESSURE TRIM
70
5
70
59
98
16
67
42019
214
27
22
25
22
71 21 70
1
1817
12
74
8
24
6
1
43
6
41
160
1245
16
15
3116
31
15
38
6
12
13
12
4
5
37
733
71
122
122
1
VALVE ONLYMODEL "H-2" 323667-HP (ANSI)MODEL "H-2" 323667-D-HP (DIN)
TRIM ONLY323580-HP
VALVE FACTORY TRIMMEDMODEL "H-2" 323792-HP (ANSI)MODEL "H-2" 323792-D-HP (DIN)
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 3 18 3/4" x 2 1/2" Nipple 310402 1 41 3/4" x 1 1/2" Nipple 310413 1
3 1/2" Tee 311303 1 19 1/2" x 2" Nipple 310302 1 43 3/4" x 3 1/2" Nipple 310404 1
4 1/2" Close Nipple 310300 3 20 1/2" Swing Check Valve 311639 1 45 1/4" x 5" Nipple 310108 1
5 1/2" Ball Valve 311692 2 21 1/2" Union 311403 2 59 Retard Chamber 323350 1
6 3/4" x 1/2" x 3/4" Tee 311313 3 22 2" x 3" Nipple 310802 2 67 1/2" x 1/4" x 1/2" Tee 311305 1
8 3/4" Elbow 311204 1 24 3/4" x 4 1/2" Nipple 310406 1 70 1/2" Close Galv. Nipple 310300-G 3
12 3/4" Close Nipple 310400 4 25 2" Angle Valve 311617 1 71 1/2" x 1 1/2" Galv. Nipple 310301-G 2
13 3/4" Swing Check Valve 311640 1 27 2" x 2" x 1/2" Tee 311380 1 73 1/2" x 2" Galv. Nipple 310302-G 1
15 1/4" 3-Way Valve 311683 2 31 3 1/2" Water Gauge (0-300psi) 300119 2 74 1/2" x 8 1/2" Galv. Nipple 310316-G 1
16 1/4" Plug 311001 3 37 1/2" x 1 1/2" Nipple 310301 1 98 1/2" x 4 1/2" Nipple 310307 1
17 3/4" Union 311404 1 38 1/4" x 2" Nipple 310102 1 122 1/2" x 1/4" Reducing Bushing 311100 2
160 ø.500 Restricted Orifice Union 311411 1
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
175psi (12bars) RATED6" MODEL “H” SERIES VERTICAL POSITION / CONSTANT PRESSURE TRIM
16
31
15
38122 6
12 13
12
31
16
1545
12
122
6
17
41
18
17
1224
8
43
6
4
5
37
3
70
170
5
70
30
103
36
35
32
34
16
67
3721
3720
37
27
53
25
22
7121
701
74
1
73
VALVE ONLYMODEL "H-1" 323560
MODEL "H-2" 323667 (ANSI)MODEL "H-2" 323667-D (DIN)
MODEL "H-3" 323590
TRIM ONLY323581
VALVE FACTORY TRIMMEDMODEL "H-1" 323576
MODEL "H-2" 323793 (ANSI)MODEL "H-2" 323793-D (DIN)
MODEL "H-3" 323596
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 3 21 1/2" Union 311403 2 38 1/4" x 2" Nipple 310102 1
3 1/2" Tee 311303 1 22 2" x 3" Nipple 310802 1 41 3/4" x 1 1/2" Nipple 310413 1
4 1/2" Close Nipple 310300 1 24 3/4" x 4 1/2" Nipple 310406 1 43 3/4" x 3 1/2" Nipple 310404 1
5 1/2" Ball Valve 311692 2 25 2" Angle Valve 311617 1 45 1/4" x 5" Nipple 310108 1
6 3/4" x 1/2" x 3/4" Tee 311313 3 27 2" x 2" x 1/2" Tee 311380 1 53 2" Close Nipple 310800 1
8 3/4" Elbow 311204 1 30 3/4" x 1/2" x 1/2" Tee 311318 1 67 1/2" x 1/4" x 1/2" Tee 311305 1
12 3/4" Close Nipple 310400 4 31 3 1/2" Water Gauge (0-300psi) 300119 2 70 1/2" Close Galv. Nipple 310300-G 4
13 3/4" Swing Check Valve 311640 1 32 1/2" Coupling 311423 1 71 1/2" x 1 1/2" Galv. Nipple 310301-G 1
15 1/4" 3-Way Valve 311683 2 34 1/2" x 12" Nipple 310318 1 73 1/2" x 2" Galv. Nipple 310302-G 1
16 1/4" Plug 311001 3 35 Alarm Line Bleeder 320506 1 74 1/2" x 8 1/2" Galv. Nipple 310316-G 1
17 3/4" Union 311404 2 36 3/4" Strainer 325535 1 103 3/4" Close Galv. Nipple 310400-G 1
18 3/4" x 2 1/2" Nipple 310402 1 37 1/2" x 1 1/2" Nipple 310301 4 122 1/2" x 1/4" Reducing Bushing 311100 2
20 1/2" Swing Check Valve 311639 1
JUNE 2016 Page 24 BULLETIN A.C.V.I.M., REV. #14
JUNE 2016 Page 25 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
300psi (20bars) RATED6" MODEL “H-2” VERTICAL POSITION / CONSTANT PRESSURE TRIM
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 3 21 1/2" Union 311403 2 41 3/4" x 1 1/2" Nipple 310413 1
3 1/2" Tee 311303 1 22 2" x 3" Nipple 310802 1 43 3/4" x 3 1/2" Nipple 310404 1
4 1/2" Close Nipple 310300 1 24 3/4" x 4 1/2" Nipple 310406 1 45 1/4" x 5" Nipple 310108 1
5 1/2" Ball Valve 311692 2 25 2" Angle Valve 311617 1 53 2" Close Nipple 310800 1
6 3/4" x 1/2" x 3/4" Tee 311313 3 27 2" x 2" x 1/2" Tee 311380 1 67 1/2" x 1/4" x 1/2" Tee 311305 1
8 3/4" Elbow 311204 1 30 3/4" x 1/2" x 1/2" Tee 311318 1 70 1/2" Close Galv. Nipple 310300-G 4
12 3/4" Close Nipple 310400 4 31 3 1/2" Water Gauge (0-300psi) 300119 2 71 1/2" x 1 1/2" Galv. Nipple 310301-G 1
13 3/4" Swing Check Valve 311640 1 32 1/2" Coupling 311423 1 73 1/2" x 2" Galv. Nipple 310302-G 1
15 1/4" 3-Way Valve 311683 2 34 1/2" x 12" Nipple 310318 1 74 1/2" x 8 1/2" Galv. Nipple 310316-G 1
16 1/4" Plug 311001 3 35 Alarm Line Bleeder 320506 1 103 3/4" Close Galv. Nipple 310400-G 1
17 3/4" Union 311404 1 36 3/4" Strainer 325535 1 122 1/2" x 1/4" Reducing Bushing 311100 2
18 3/4" x 2 1/2" Nipple 310402 1 37 1/2" x 1 1/2" Nipple 310301 4 160 ø.500 Restricted Orifice Union 311411 1
20 1/2" Swing Check Valve 311639 1 38 1/4" x 2" Nipple 310102 1
16
31
15
38122 6
1213
12
31
16
1545
12
122
6
160
41
18
17
1224
8
43
6
4
5
37
3
70
170
5
70
30
103
36
35
32
34
16
67
3721
3720
37
27
53
25
22
7121
70 1
74
1
73
VALVE ONLYMODEL "H-2" 323667-HP (ANSI)MODEL "H-2" 323667-D-HP (DIN)
TRIM ONLY323581-HP
VALVE FACTORY TRIMMEDMODEL "H-2" 323793-HP (ANSI)MODEL "H-2" 323793-D-HP (DIN)
JUNE 2016 Page 26 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
175psi (12bars) RATED6" MODEL “H” SERIES HORIZONTAL POSITION / VARIABLE PRESSURE TRIM
1
70
5
70
59
4
67
16
3920
39
21
39
27
69
25
75
1
72
3
37
5
4
6
12
43
8
24
6
122
11 12
6
1213
12
17
41
70
1
74
1
73
68
2171
18
17
122
11
28
28
29
42
60
15
16
31
42
15
16
31
VALVE ONLYMODEL "H-1" 323560
MODEL "H-2" 323667 (ANSI)MODEL "H-2" 323667-D (DIN)
MODEL "H-3" 323590
TRIM ONLY323623
VALVE FACTORY TRIMMEDMODEL "H-1" 323617
MODEL "H-2" 323794 (ANSI)MODEL "H-2" 323794-D (DIN)
MODEL "H-3" 323620
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 4 20 1/2" Swing Check Valve 311639 1 59 Retard Chamber 323350 1
3 1/2" Tee 311303 1 21 1/2" Union 311403 2 60 1/4" Coupling 311402 1
4 1/2" Close Nipple 310300 2 24 3/4" x 4 1/2" Nipple 310406 1 67 1/2" x 1/4" x 1/2" Tee 311305 1
5 1/2" Ball Valve 311692 2 25 2" Angle Valve 311617 1 68 2" x 7 1/2" Nipple 310809 1
6 3/4" x 1/2" x 3/4" Tee 311313 3 27 2" x 2" x 1/2" Tee 311380 1 69 2" x 6" Nipple 310808 1
8 3/4" Elbow 311204 1 28 1/4" Elbow 311201 2 70 1/2" Close Galv. Nipple 310300-G 3
11 1/4" x 6 1/2" Nipple 310115 2 29 1/4" x 10" Nipple 310136 1 71 1/2" x 1 1/2" Galv. Nipple 310301-G 1
12 3/4" Close Nipple 310400 4 31 3 1/2" Water Gauge (0-300psi) 300119 2 72 1/2" x 2 1/2" Galv. Nipple 310303-G 1
13 3/4" Swing Check Valve 311640 1 37 1/2" x 1 1/2" Nipple 310301 1 73 1/2" x 2" Galv. Nipple 310302-G 1
15 1/4" 3-Way Valve 311683 2 39 1/2" x 2 1/2" Nipple 310303 3 74 1/2" x 8 1/2" Galv. Nipple 310316-G 1
16 1/4" Plug 311001 3 41 3/4" x 1 1/2" Nipple 310413 1 75 1/2" x 12" Galv. Nipple 310318-G 1
17 3/4" Union 311404 2 42 1/4" x 6" Nipple 310110 2 122 1/2" x 1/4" Reducing Bushing 311100 2
18 3/4" x 2 1/2" Nipple 310402 1 43 3/4" x 3 1/2" Nipple 310404 1
JUNE 2016 Page 27 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
300psi (20bars) RATED6" MODEL “H-2” HORIZONTAL POSITION / VARIABLE PRESSURE TRIM
1
70
5
70
59
4
67
16
3920
39
21
39
27
69
25
75
1
72
3
37
5
4
6
12
43
8
24
6
122
11 12
6
12 13
12
160
41
70
1
74
1
73
68
2171
18
17
122
11
28
28
29
42
60
15
16
31
42
15
16
31
VALVE ONLYMODEL "H-2" 323667-HP (ANSI)MODEL "H-2" 323667-D-HP (DIN)
TRIM ONLY323623-HP
VALVE FACTORY TRIMMEDMODEL "H-2"
323794-HP (ANSI)323794-D-HP (DIN)
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 4 20 1/2" Swing Check Valve 311639 1 59 Retard Chamber 323350 1
3 1/2" Tee 311303 1 21 1/2" Union 311403 2 60 1/4" Coupling 311402 1
4 1/2" Close Nipple 310300 2 24 3/4" x 4 1/2" Nipple 310406 1 67 1/2" x 1/4" x 1/2" Tee 311305 1
5 1/2" Ball Valve 311692 2 25 2" Angle Valve 311617 1 68 2" x 7 1/2" Nipple 310809 1
6 3/4" x 1/2" x 3/4" Tee 311313 3 27 2" x 2" x 1/2" Tee 311380 1 69 2" x 6" Nipple 310808 1
8 3/4" Elbow 311204 1 28 1/4" Elbow 311201 2 70 1/2" Close Galv. Nipple 310300-G 3
11 1/4" x 6 1/2" Nipple 310115 2 29 1/4" x 10" Nipple 310136 1 71 1/2" x 1 1/2" Galv. Nipple 310301-G 1
12 3/4" Close Nipple 310400 4 31 3 1/2" Water Gauge (0-300psi) 300119 2 72 1/2" x 2 1/2" Galv. Nipple 310303-G 1
13 3/4" Swing Check Valve 311640 1 37 1/2" x 1 1/2" Nipple 310301 1 73 1/2" x 2" Galv. Nipple 310302-G 1
15 1/4" 3-Way Valve 311683 2 39 1/2" x 2 1/2" Nipple 310303 3 74 1/2" x 8 1/2" Galv. Nipple 310316-G 1
16 1/4" Plug 311001 3 41 3/4" x 1 1/2" Nipple 310413 1 75 1/2" x 12" Galv. Nipple 310318-G 1
17 3/4" Union 311404 1 42 1/4" x 6" Nipple 310110 2 122 1/2" x 1/4" Reducing Bushing 311100 2
18 3/4" x 2 1/2" Nipple 310402 1 43 3/4" x 3 1/2" Nipple 310404 1 160 ø.500 Restricted Orifice Union 311411 1
JUNE 2016 Page 28 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
175psi (12bars) RATED6" MODEL “H” SERIES HORIZONTAL POSITION / CONSTANT PRESSURE TRIM
31
16
15
42
60
31
16
15
29 42
2828
1111
122
12
66
122
12
24
12
13
8
12
6
4
5
69
27
37
21
37
2037
3235
36103
30
73
5
16
70
67
73
3
37
73
25
1
74
69
1
70
21
7141
1717
18
43
VALVE ONLYMODEL "H-1" 323560
MODEL "H-2" 323667 (ANSI)MODEL "H-2" 323667-D (DIN)
TRIM ONLY323624
VALVE FACTORY TRIMMEDMODEL "H-1" 323618
MODEL "H-2" 323795 (ANSI)MODEL "H-2" 323795-D (DIN)
MODEL "H-3" 323621
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 2 20 1/2" Swing Check Valve 311639 1 41 3/4" x 1 1/2" Nipple 310413 1
3 1/2" Tee 311303 1 21 1/2" Union 311403 2 42 1/4" x 6" Nipple 310110 2
4 1/2" Close Nipple 310300 1 24 3/4" x 4 1/2" Nipple 310406 1 43 3/4" x 3 1/2" Nipple 310404 1
5 1/2" Ball Valve 311692 2 25 2" Angle Valve 311617 1 60 1/4" Coupling 311402 1
6 3/4" x 1/2" x 3/4" Tee 311313 3 27 2" x 2" x 1/2" Tee 311380 1 67 1/2" x 1/4" x 1/2" Tee 311305 1
8 3/4" Elbow 311204 1 28 1/4" Elbow 311201 2 69 2" x 6" Nipple 310808 2
11 1/4" x 6 1/2" Nipple 310115 2 29 1/4" x 10" Nipple 310136 1 70 1/2" Close Galv. Nipple 310300-G 2
12 3/4" Close Nipple 310400 4 30 3/4" x 1/2" x 1/2" Tee 311318 1 71 1/2" x 1 1/2" Galv. Nipple 310301-G 1
13 3/4" Swing Check Valve 311640 1 31 3 1/2" Water Gauge (0-300psi) 300119 2 73 1/2" x 2" Galv. Nipple 310302-G 3
15 1/4" 3-Way Valve 311683 2 32 1/2" Coupling 311423 1 74 1/2" x 8 1/2" Galv. Nipple 310316-G 1
16 1/4" Plug 311001 3 35 Alarm Line Bleeder 320506 1 103 3/4" Close Galv. Nipple 310400-G 1
17 3/4" Union 311404 2 36 3/4" Strainer 325535 1 122 1/2" x 1/4" Reducing Bushing 311100 2
18 3/4" x 2 1/2" Nipple 310402 1 37 1/2" x 1 1/2" Nipple 310301 4
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
300psi (20bars) RATED6" MODEL “H-2” HORIZONTAL POSITION / CONSTANT PRESSURE TRIM
31
16
15
42
60
31
16
15
29 42
2828
1111
122 12
66
122
12
24
12
13
8
12
6
4
5
69
27
37
21
37
2037
3235
36103
30
73
5
16
70
67
73
3
37
7325
1
74
69
1
70
21
7141
160
17
18
43 VALVE ONLYMODEL "H-2" 323667-HP (ANSI)MODEL "H-2" 323667-D-HP (DIN)
TRIM ONLY323624-HP
VALVE FACTORY TRIMMEDMODEL "H-2" 323795-HP (ANSI)MODEL "H-2" 323795-D-HP (DIN)
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 2 20 1/2" Swing Check Valve 311639 1 41 3/4" x 1 1/2" Nipple 310413 1
3 1/2" Tee 311303 1 21 1/2" Union 311403 2 42 1/4" x 6" Nipple 310110 2
4 1/2" Close Nipple 310300 1 24 3/4" x 4 1/2" Nipple 310406 1 43 3/4" x 3 1/2" Nipple 310404 1
5 1/2" Ball Valve 311692 2 25 2" Angle Valve 311617 1 60 1/4" Coupling 311402 1
6 3/4" x 1/2" x 3/4" Tee 311313 3 27 2" x 2" x 1/2" Tee 311380 1 67 1/2" x 1/4" x 1/2" Tee 311305 1
8 3/4" Elbow 311204 1 28 1/4" Elbow 311201 2 69 2" x 6" Nipple 310808 2
11 1/4" x 6 1/2" Nipple 310115 2 29 1/4" x 10" Nipple 310136 1 70 1/2" Close Galv. Nipple 310300-G 2
12 3/4" Close Nipple 310400 4 30 3/4" x 1/2" x 1/2" Tee 311318 1 71 1/2" x 1 1/2" Galv. Nipple 310301-G 1
13 3/4" Swing Check Valve 311640 1 31 3 1/2" Water Gauge (0-300psi) 300119 2 73 1/2" x 2" Galv. Nipple 310302-G 3
15 1/4" 3-Way Valve 311683 2 32 1/2" Coupling 311423 1 74 1/2" x 8 1/2" Galv. Nipple 310316-G 1
16 1/4" Plug 311001 3 35 Alarm Line Bleeder 320506 1 103 3/4" Close Galv. Nipple 310400-G 1
17 3/4" Union 311404 1 36 3/4" Strainer 325535 1 122 1/2" x 1/4" Reducing Bushing 311100 2
18 3/4" x 2 1/2" Nipple 310402 1 37 1/2" x 1 1/2" Nipple 310301 4 160 ø.500 Restricted Orifice Union 311411 1
JUNE 2016 Page 29 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
175psi (12bars) RATED8" MODEL “H” SERIES VERTICAL POSITION / VARIABLE PRESSURE TRIM
JUNE 2016 Page 30 BULLETIN A.C.V.I.M., REV. #14
59
33
67
16
4
20
33
21
53
25
66
27
4
96
1
70
21
87
3
72
1
71
5 71
39
61
65
1817
12
6
122
91
1
3763
126
18
13
47
4
1122
109
15
31
16
47
45
15
31
16
17
12
VALVE ONLYMODEL "H-1" 323830MODEL "H-2" 323859MODEL "H-3" 323852
TRIM ONLY323862
VALVE FACTORY TRIMMEDMODEL "H-1" 323860MODEL "H-2" 323866MODEL "H-3" 323864
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 4 21 1/2" Union 311403 2 63 3/4" x 3/4" x 1/2" Tee 311317 1
3 1/2" Tee 311303 1 25 2" Angle Valve 311617 1 65 1/2" x 6" Nipple 310310 1
4 1/2" Close Nipple 310300 3 27 2" x 2" x 1/2" Tee 311380 1 66 2" x 7 1/2" Nipple 310809 1
5 1/2" Ball Valve 311692 1 31 3 1/2" Water Gauge (0-300psi) 300119 2 67 1/2" x 1/4" x 1/2" Tee 311305 1
6 3/4" x 1/2" x 3/4" Tee 311313 2 33 1/2" x 3 1/2" Nipple 310305 2 70 1/2" Close Galv. Nipple 310300-G 1
12 3/4" Close Nipple 310400 3 37 1/2" x 1 1/2" Nipple 310301 1 71 1/2" x 1 1/2" Galv. Nipple 310301-G 2
13 3/4" Swing Check Valve 311640 1 39 1/2" x 2 1/2" Nipple 310303 1 72 1/2" x 2 1/2" Galv. Nipple 310303-G 1
15 1/4" 3-Way Valve 311683 2 45 1/4" x 5" Nipple 310108 1 87 1/2" x 3" Galv. Nipple 310304-G 1
16 1/4" Plug 311001 3 47 3/4" x 2" Nipple 310401 2 91 1/4" Street Elbow 311211 1
17 3/4" Union 311404 2 53 2" Close Nipple 310800 1 96 1/2" x 3 1/2" Galv. Nipple 310305-G 1
18 3/4" x 2 1/2" Nipple 310402 2 59 Retard Chamber 323350 1 109 1/4" x 3 1/2" Nipple 310105 1
20 1/2" Swing Check Valve 311639 1 61 1/2" Angle Valve 311612 1 122 1/2" x 1/4" Reducing Bushing 311100 2
JUNE 2016 Page 31 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
300psi (20bars) RATED8" MODEL “H-2” VERTICAL POSITION / VARIABLE PRESSURE TRIM
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 4 21 1/2" Union 311403 2 63 3/4" x 3/4" x 1/2" Tee 311317 1
3 1/2" Tee 311303 1 25 2" Angle Valve 311617 1 65 1/2" x 6" Nipple 310310 1
4 1/2" Close Nipple 310300 3 27 2" x 2" x 1/2" Tee 311380 1 66 2" x 7 1/2" Nipple 310809 1
5 1/2" Ball Valve 311692 1 31 3 1/2" Water Gauge (0-300psi) 300119 2 67 1/2" x 1/4" x 1/2" Tee 311305 1
6 3/4" x 1/2" x 3/4" Tee 311313 2 33 1/2" x 3 1/2" Nipple 310305 2 70 1/2" Close Galv. Nipple 310300-G 1
12 3/4" Close Nipple 310400 3 37 1/2" x 1 1/2" Nipple 310301 1 71 1/2" x 1 1/2" Galv. Nipple 310301-G 2
13 3/4" Swing Check Valve 311640 1 39 1/2" x 2 1/2" Nipple 310303 1 72 1/2" x 2 1/2" Galv. Nipple 310303-G 1
15 1/4" 3-Way Valve 311683 2 45 1/4" x 5" Nipple 310108 1 87 1/2" x 3" Galv. Nipple 310304-G 1
16 1/4" Plug 311001 3 47 3/4" x 2" Nipple 310401 2 91 1/4" Street Elbow 311211 1
17 3/4" Union 311404 1 53 2" Close Nipple 310800 1 96 1/2" x 3 1/2" Galv. Nipple 310305-G 1
18 3/4" x 2 1/2" Nipple 310402 2 59 Retard Chamber 323350 1 109 1/4" x 3 1/2" Nipple 310105 1
20 1/2" Swing Check Valve 311639 1 61 1/2" Angle Valve 311612 1 122 1/2" x 1/4" Reducing Bushing 311100 2
161 ø.562 Restricted Orifice Union 311412 1
59
33
67
16
420
33
21
53
25
66
27
4
96
1
70
21
87
3
72
1
71
5 71
39
61
65
18161
12
6
122
91
1
3763
126
18
13
47
4
1122
109
15
31
16
47
45
15
31
16
17
12
VALVE ONLYMODEL "H-2" 323859-HP
TRIM ONLY323862-HP
VALVE FACTORY TRIMMEDMODEL "H-2" 323866-HP
JUNE 2016 Page 32 BULLETIN A.C.V.I.M., REV. #14
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
175psi (12bars) RATED8" MODEL “H” SERIES VERTICAL POSITION / CONSTANT PRESSURE TRIM
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 4 25 2" Angle Valve 311617 1 61 1/2" Angle Valve 311612 1
3 1/2" Tee 311303 1 27 2" x 2" x 1/2" Tee 311380 1 63 3/4" x 3/4" x 1/2" Tee 311317 1
4 1/2" Close Nipple 310300 4 30 3/4" x 1/2" x 1/2" Tee 311318 1 65 1/2" x 6" Nipple 310310 1
5 1/2" Ball Valve 311692 1 31 3 1/2" Water Gauge (0-300psi) 300119 2 66 2" x 7 1/2" Nipple 310809 1
6 3/4" x 1/2" x 3/4" Tee 311313 2 32 1/2" Coupling 311423 1 67 1/2" x 1/4" x 1/2" Tee 311305 1
12 3/4" Close Nipple 310400 2 34 1/2" x 12" Nipple 310318 1 70 1/2" Close Galv. Nipple 310300-G 1
13 3/4" Swing Check Valve 311640 1 35 Alarm Line Bleeder 320506 1 71 1/2" x 1 1/2" Galv. Nipple 310301-G 3
15 1/4" 3-Way Valve 311683 2 36 3/4" Strainer 325535 1 87 1/2" x 3" Galv. Nipple 310303-G 1
16 1/4" Plug 311001 3 37 1/2" x 1 1/2" Nipple 310301 1 91 1/4" Street Elbow 311211 1
17 3/4" Union 311404 1 39 1/2" x 2 1/2" Nipple 310303 1 96 1/2" x 3 1/2" Galv. Nipple 310305-G 1
18 3/4" x 2 1/2" Nipple 310402 2 45 1/4" x 5" Nipple 310108 1 103 3/4" Close Galv. Nipple 310400-G 1
20 1/2" Swing Check Valve 311639 1 47 3/4" x 2" Nipple 310401 2 109 1/4" x 3 1/2" Nipple 310105 1
21 1/2" Union 311403 2 53 2" Close Nipple 310800 1 122 1/2" x 1/4" Reducing Bushing 311100 2
36
103
30
3571
571
132
3471
3
87
2116
6770
1
96
39
61
65
18
1712
6
122
91109
31
15
16
47
13
18
6 12
6337
1
474
1
12245
15
31
16
25
66
27
4
21
4
20
453
VALVE ONLYMODEL "H-1" 323830MODEL "H-2" 323859MODEL "H-3" 323852
TRIM ONLY323863
VALVE FACTORY TRIMMEDMODEL "H-1" 323861MODEL "H-2" 323867MODEL "H-3" 323865
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
300psi (20bars) RATED8" MODEL “H-2” VERTICAL POSITION / CONSTANT PRESSURE TRIM
JUNE 2016 Page 33 BULLETIN A.C.V.I.M., REV. #14
36
103
30
3571
571
132
3471
3
87
2116
6770
1
96
39
61
65
18
16112
6
122
91109
31
15
16
47
13
18
6 12
6337
1
474
1
12245
15
31
16
25
66
27
4
21
4
20
453
VALVE ONLYMODEL "H-2" 323859-HP
TRIM ONLY323863-HP
VALVE FACTORY TRIMMEDMODEL "H-2" 323867-HP
Det. No. Description Part No. Req'd. Det.
No. Description Part No. Req'd. Det. No. Description Part No. Req'd.
1 1/2" Elbow 311203 4 27 2" x 2" x 1/2" Tee 311380 1 63 3/4" x 3/4" x 1/2" Tee 311317 1
3 1/2" Tee 311303 1 30 3/4" x 1/2" x 1/2" Tee 311318 1 65 1/2" x 6" Nipple 310310 1
4 1/2" Close Nipple 310300 4 31 3 1/2" Water Gauge (0-300psi) 300119 2 66 2" x 7 1/2" Nipple 310809 1
5 1/2" Ball Valve 311692 1 32 1/2" Coupling 311423 1 67 1/2" x 1/4" x 1/2" Tee 311305 1
6 3/4" x 1/2" x 3/4" Tee 311313 2 34 1/2" x 12" Nipple 310318 1 70 1/2" Close Galv. Nipple 310300-G 1
12 3/4" Close Nipple 310400 2 35 Alarm Line Bleeder 320506 1 71 1/2" x 1 1/2" Galv. Nipple 310301-G 3
13 3/4" Swing Check Valve 311640 1 36 3/4" Strainer 325535 1 87 1/2" x 3" Galv. Nipple 310303-G 1
15 1/4" 3-Way Valve 311683 2 37 1/2" x 1 1/2" Nipple 310301 1 91 1/4" Street Elbow 311211 1
16 1/4" Plug 311001 3 39 1/2" x 2 1/2" Nipple 310303 1 96 1/2" x 3 1/2" Galv. Nipple 310305-G 1
18 3/4" x 2 1/2" Nipple 310402 2 45 1/4" x 5" Nipple 310108 1 103 3/4" Close Galv. Nipple 310400-G 1
20 1/2" Swing Check Valve 311639 1 47 3/4" x 2" Nipple 310401 2 109 1/4" x 3 1/2" Nipple 310105 1
21 1/2" Union 311403 2 53 2" Close Nipple 310800 1 122 1/2" x 1/4" Reducing Bushing 311100 2
25 2" Angle Valve 311617 1 61 1/2" Angle Valve 311612 1 161 ø.562 Restricted Orifice Union 311412 1
GLOBE ALARM CHECK VALVEINSTALLATION AND MAINTENANCE GUIDE
OPTIONAL ALARM PRESSURE SWITCH TRIM
JUNE 2016 Page 34 BULLETIN A.C.V.I.M., REV. #14
FOR USE WHEN MECHANICAL SWITCHIS PROVIDED WITH MECHANICAL ALARM.
FOR USE WHEN SWITCH IS PROVIDED WITHOUTMECHANICAL ALARM, TO PREVENT AIR LOCKS.
5
3
2
4
1
TO DRAIN
5
2
3
6
7
4
1
Det. No. Description Part No. Req'd.
1 3/4" x 4 1/2" Nipple 310406 12 1/2" x 4" Nipple 310306 13 1/2" Elbow 311203 14 3/4" x 3/4" x 1/2" Tee 311317 1
5 Pressure Switch* (Sold Separately) 301650 1
Part Number 323485 (Trim Only (Det. No. 1-4))Det. No. Description Part No. Req'd.
1 3/4" x 4 1/2" Nipple 310406 12 1/2" x 4" Nipple 310306 13 1/2" Elbow 311203 14 3/4" x 1/2" x 1/2" Tee 311318 16 Alarm Line Bleeder 320506 17 1/2" Coupling 311423 1
5 Pressure Switch* (Sold Separately) 301650 1
Part Number 323478 (Trim Only (Det. No. 1-4, 6 & 7))
*NOTE: Other pressure switches available upon request. May be substituted depending on application.
OPTIONAL PRESSURERELIEF VALVE TRIM
(EXISTING TRIM)
(EXISTING TRIM - SYSTEM SIDE)
67
2
3
2
1
15
Det. No. Description Part No. Req'd.
1 1/4" Pressure Relief Valve 323640 12 1/4"NPT Male x 1/4" Tube Elbow 320603 23 1/4" Copper Tubing M-320604 2'
Part Number 323477 (Trim with Pressure Relief Valve)
PART NUMBER 323470 (TRIM (DET. NO. 1-14) ONLY)DESCRIPTIONQTYPART NUMBERITEM
¾" CLOSE NIPPLE13104001
½" x ½" x ¾" TEE13113892
½" x 1½" NIPPLE13103013
½"ELBOW13112034
1/2" x 4 1/2" NIPPLE33103075
1/2" BALL VALVE23116926
#6-32 x 1" SOCKET HEAD CAP SCREW43016777
½" x 3½" NIPPLE13103058
½" TEE13113039
ALARM LINE BLEEDER132050610
½" COUPLING131142311
SUPERVISORY SWITCH230167812
BRACKET230167513
U-BOLT230167614
PRESSURE SWITCH (SOLD SEPARATELY)230165015
SHT 1 OF 12/12/2013SCALE: NOT TO SCALE
323470
GLOBE FIRE SPRINKLER CORP.STANDISH, MI U.S.A.
NORWEGIAN TRIM ADD ON FOR
METRIC UNITS SHOWN IN BRACKETS, DUE TO THE CONVERSION, METRIC VALUES
MAY BE APPROXIMATE. LIMITS ON: FRACTIONS 1/64 [.4MM];
2 PLC. DEC. .010 [.3MM]; 3 PLC. DEC. .005 [.1MM]; ANGLES 1/2
NO. REVISION DATE BY APR.
APR. BY: DR. BY: LEANN SANGSLAND
VERTICAL INSTALLATION / VARIABLE PRESSURE ALARM CHECK VALVE
PRESSURE SWITCHES (301650 (DET 15))SOLD SEPARATELY
AADDED SUPERVISORY SWITCHES AND BRACKETS ASOPTIONS, REDESIGNED TRIM TO ALLOW FOR SUPERVISORYSWITCHES TO BE ADDED WHEN REQUESTED ON ORDER 3/10/15 LS
BTH
LS11/11/15
SUPERVISORY SWITCHES, BRACKETS, U-BOLTS AND SHCSsARE NOW SOLD AS PART OF TRIM AS A UNIT (323470);PRESSURE SWITCHES ARE TO BE SOLD SEPARATELY;SUPERVISORY SWITCH PART NUMBER FROM 301672 TO 301678B
BTH
6
5
4
3
2
6
15
1
8
5
9
15
10
11
TO DRAIN
12
13
13
14
14
12
77
77B
OPTIONAL DOUBLE ALARMPRESSURE SWITCH TRIM
TO DRAIN
5
2
3
6
7
4
1
2
3
6
7
RETARD VENT KIT Part Number 323476
PART NUMBER 323470 (Trim (Det. No. 1-14 Only)
Det. No. Description Part No. Req’d.
1 3/4” Close Nipple 310400 1
2 1/2” x 1/2” x 3/4” Tee 311389 1
3 1/2” x 1 1/2” Nipple 310301 1
4 1/2” Elbow 311203 1
5 1/2” x 4 1/2” Nipple 310307 2
6 1/2” Ball Valve 311692 2
7 #8-32 x 1” SHCS 301677 4
8 1/2” x 3 1/2” Nipple 310305 1
9 1/2” Tee 311303 1
10 Alarm Line Bleeder 320506 1
11 1/2” Coupling 311423 1
12 Supervisory Switch 301678 2
13 Bracket 301675 2
14 U-Bolt 301676 2
15 Pressure Switch (Sold Separately) 301650 2