Quick Start

EchoLife HG850a GPON Terminal

1

Safety Precautions

To use the device properly and safely, read the safety precautions carefully before using the device and strictly observe these precautions when using the device.

� Do not look directly into the optical port without eye protection. � Keep the device out of the reach of children as the components or accessories may be swallowed. � Install the device in strict compliance with the requirements of the supplier. Reserve a space of

at least 10 cm above and around the device for heat dissipation. During the installation, keep the device away from electric appliances that generate strong magnetic or electric fields, such as microwave ovens, refrigerators, and mobile phones.

� The power supply voltage of the device must meet the requirements on the input voltage of the device.

� Do not use any power adapters that are not in the standard configuration. Otherwise, the device may be abnormal or unsafe.

� Dry your hands before connecting or disconnecting cables. Stop the device and switch off the power before connecting or disconnecting cables.

� Do not place any object on the device, so that the device will not be damaged due to overheating or deformation.

� Prevent objects, such as metal, from entering the device through the heat dissipation hole. � Switch off the power and disconnect all cables, including the power cable, optical fiber, and

network cable, during periods of lightning activities. � Do not lead the strength member of the optical fiber or other metal parts indoors. Do not install

telephone lines, network cables, power adapters or power adapter cables outdoors. Adopting these measures will help prevent device damage and bodily injuries which are especially prone during thunderstorms.

� If an abnormality occurs, for example, liquid entering the device, smoke, unusual sound, and smell, stop the device immediately, switch off the power, disconnect all cables (such as the power cable, optical cable, and network cable) to the device, and contact the authorized service center.

� Do not disassemble the device without permission. In the case of a device fault, contact the authorized service center.

� Dispose of the packing materials, expired batteries, and old or abandoned devices in accordance to local laws and regulations (recycling them is strongly recommended).

� Do not change the structure, safety design, or performance design of the device without prior authorization.

Packing ListAfter opening the product packaging, check each item against the following checklist. Contact the supplier if there are any discrepancies.

No. Item Quantity

1 GPON Terminal 1

2 Power Adapter or Battery Backup Unit 1

3 Ethernet Cable 1

4 Quick Start 1

2

The HG850a can be placed on a horizontal surface or be installed on the wall.To install the HG850a on the wall, do as follows:Step 1 Mark the positions of the two holes used for fixing the HG850a on the wall. The distance between the two holes is 111.5 mm.Step 2 Choose an appropriate drill bit according to the outer diameter of the mounting screw. Drill at the positions marked on the wall by using a percussion drill.Step 3 Fix the mounting screws at the positions of the holes on the wall by using a screwdriver.Step 4 Mount the HG850a horizontally or vertically onto the mounting screws. The following figures show the horizontal installation of the HG850a.

Installing the HG850a

The information in this document is subject to change without notice. Every effort has been made in the preparation of this document to ensure accuracy of the contents, but all statements, information, and recommendations in this document do not constitute the warranty of any kind, express or implied.

3

The following figures show the vertical installation of the HG850a.

The figures in this document are only for your reference. Though the actual product may be different, the functions of the product will remain the same.

Installing the HG850a

Connecting cablesThe connections between the HG850a and other devices are shown as follows.

Optical interface in the wall

IP set-top box (STB) PC

Telephone Fax machine Power adapter

1

4

2 3

5 6

1

2

5

6

43

4

Connect the TEL interfaces to the telephone by using a telephone line.

The HG850a can be directly connected to the TEL interfaces and Fax machine. The connection method is similar to the previously-mentioned steps.

Connect the OPTICAL interface to the optical interface in the wall by using the optical fiber.

Connect the HG850a to the external devices according to the following steps and

previous figure.

Connecting cables

The cable in the figture is for reference only. The type of the optical connecteor connected to the OPTICAL interface is SC/APC, and the type of the optical connector connected to the optical in the wall is determined according to actual conditions.

5

Power on the HG850a.

Plug the power adapter (input voltage: 100 - 240 V AC, output voltage: 11 - 14 V DC) to the POWER interface of the HG850a.

The HG850a can be directly connected to other devices, such as PCs and IP set-top boxes (STBs). The connection method is similar to the previously-mentioned steps.

Connect the LAN interfaces to the upstream interface of the switch by using the Ethernet cable.

Connecting cables

6

Logging in to the Web Configuration Window

Item SpecificationsDimensions (L x W x H) 195 mm x 155 mm x 33 mmWeight < 700 gPower supply 11 - 14 V DC, 1 APower adapter input 100 - 240 V AC, 50 - 60 HzPower consumption < 8 WOperating temperature 0 - 40 oC Operating humidity 5 - 95 % (non-condensing)

Technical Specifications

Step 1 Set the IP address of the PC in the same subnet as the management IP address of the GPON terminal. For example,

-IP address: 192.168.100.100 -Subnet mask: 255.255.255.0

Step 2 Enter the management IP address of the GPON terminal in the address bar of Internet Explorer and press Enter.

The login window is displayed. Step 3 In the login window, select your preferred language, enter the user name and

password (default user name is root and default password is admin), and click Login. After the password is authenticated, the Web configuration window is displayed.

The default management IP address and subnet mask of the GPON terminal are as follows: -IP address: 192.168.100.1-Subnet mask: 255.255.255.0

-If you do not perform any operations after logging in to the system for five minutes, you will exit the system and the system automatically returns to the login interface.-The system will be locked if you input incorrect user name and password three consecutive times. One minute later, it will be unlocked. -Change the initial password after logging in to the web page.

7

Indicator Status Description

POWEROn The HG850a is powered on.

Off The HG850a is powered off.

AUTH Refer to the next table Refer to the next table.

LINK Refer to the next table Refer to the next table.

LAN

On The device is connected to the Ethernet.

Blinking Data is being transmitted through the Ethernet interface.

Off The device is not connected to the Ethernet.

TELOn The TEL interface is in the call status.Blinking The TEL interface is in the ringing status.Off The TEL interface is idle.

VoIPOn The VoIP function is enabled.Off The VoIP function is disabled..

NumberStatus

DescriptionLINK AUTH

1 Off Off Initial-state2 Slow blinking Off Standby-state3 Fast blinking Slow blinking Serial-Number-state4 Fast blinking On Ranging-state5 On On Operation-state (normal working status)6 Fast blinking Off POPUP-state7 On Off Emergency-Stop-state8 Slow blinking Slow blinking The HG850a is detected as a rouge ONT.

The following table lists the descriptions of the indicators on the front panel.

Link and Auth are the indicators of the GPON. The status of Link and Auth reflects the connection between the HG850a and the optical line terminal (OLT). The frequency of fast blinking is 3 Hz, while the frequency of slow blinking is 1 Hz.

Descriptions of the Indicators

8

The POWER indicator is off. � Check whether the ON/OFF button on the rear panel is pressed. � Check whether the power adapter matches the HG850a. � Check whether the power connection is correct.

The LINK indicator is off.

� Check whether the optical fiber is connected correctly. � Check whether there is dirt on the optical connector.

The LINK indicator is on,but the AUTH indicator is off

� The HG850a may not receive the downstream optical signal sent by the service provider. Contact the service provider for help.

The LAN indicator is off.

� Check whether the Ethernet cable delivered with the device is used. � Check whether the Ethernet cable is connected correctly. � Check whether the indicator of the network adapter is on. � Check whether the network adapter works normally: Check whether there are devices with the ? or ! mark under Network adapters. If there are such devices, uninstall and then re-install them, or insert the network adapter into another slot. If the problem remains, insert the network adapter into another slot.

The VoIP indicator is off.

� Check whether to provision the VoIP service.

� Check whether the phone works in the normal state.

The TEL indicator is off. � Check whether the telephone cable delivered with the device is used.

� Check whether the connection of the telephone cable is correct.

� Check whether the telephone is onhook.

FAQs

User Information

Warranty CardThank you for choosing Huawei Technologies Co., Ltd. To get better services, please read this warranty card carefully, fill in the required information, and preserve this card in good condition.

Preserve well. No reissue.

Dealer's Seal

Personal or company's full name:

Address/Postal Code:

Telephone:

Email:

Product Type:

Product Serial Number:

Purchase Date:

Invoice Number:

Dealer's Name:

Dealer's Address:

Dealer's Telephone:

Limited Warranty

Huawei Technologies Co., Ltd.

Address: Huawei Industrial BaseBantian, LonggangShenzhen 518129People's Republic of ChinaWebsite: www.huawei.com Email:support@huawei.com

Subject to the exclusions contained below, Huawei Technologies Co., Ltd. (hereinafter referred to as Huawei) warrants its access terminals (“Products”) to be free from defects in materials and workmanship under normal consumer usage for one year from the date of purchase of the product ("Warranty period"). During the warranty period, a Huawei authorized service partner shall remedy defects in materials and workmanship free of charge.Special Notice:(1) The warranty card shall be applicable only after being stamped by the dealer.(2) The warranty card must be preserved in good condition and free of any scratch or alteration.(3) To claim such service for defects that are not included in the following exclusion terms, the warranty card and the invoice that records the product serial number shall be presented to a Huawei authorized service partner.Exclusions:In any of the following cases, the warranty card becomes unenforceable or inapplicable without prior notice:(1) The defects are caused by improper handling in transportation and assembly.(2) The defects are caused by the fact that the product is dismantled or altered by anyone that is not from a Huawei authorized service partner.(3) The defects are caused by the fact that the product is used in a harsh environment that is not suitable for the operation of the product.(4) The defects are caused by any force majeure including but not limited to fire, earthquake, lightning and tsunami.(5) The defects are caused by the fact that the product is used or handled improperly, roughly or not as instructed in the applicable User Guide.(6) The normal wear and tear, including but not limited to the normal wear and tear of the shell and the power module, shall not be covered by the limited warranty.(7) The warranty card is altered or illegible, or the product serial number recorded on the warranty card is inconsistent with the actual one imprinted or labeled on the product.In any case that is not covered by this limited warranty or should the warranty expire, Huawei shall charge for the service(s) claimed for the products if the product is still remediable. Huawei preserves the right for interpretation of this limited warranty.

Issue: 06(2012-06-30)BOM number: 31502428

Qualification Card

Copyright © Huawei Technologies Co., Ltd. 2012 All rights reserved.No part of this document may be reproduced or transmitted in any form or by any means without prior written consent of Huawei Technologies Co., Ltd.

Trademarks and Permissions

and other Huawei trademarks are trademarks of Huawei Technologies Co., Ltd.

All other trademarks and trade names mentioned in this document are the property of their respective holders.

NoticeThe information in this document is subject to change without notice. Unless otherwise stated, this guide serves only as a guide. All statements, information, and recommendations in this document do not constitute a warranty of any kind, expressed or implied.

PASS