STARTMONKEY400 QUICK START GUIDE HIGH-POWERED RUGGED EMERGENCY JUMP STARTER Locate the battery terminals. Check the battery is 12V and maximum 1200 Cold Cranking Amps Leave the startmonkey400 attached to the vehicle battery for up to 60 seconds and then turn on vehicle ignition as normal DO NOT remove the startmonkey400 if the green LED array is illuminated. The unit must be turned off first Connect the black crocodile clip to the – terminal and the red crocodile clip to the + terminal. The startmonkey400 unit should switch on automatically If vehicle does not start first time, remove clips and then repeat steps 2-4. In very cold temperatures this process may have to be repeated several times If the vehicle battery is below 6V the startmonkey400 will need to be switched on manually by pressing the ON/OFF button twice in quick succession Once the vehicle has started the startmonkey400 will turn off automatically and can be removed. The startmonkey400 can also be switched off manually by holding down the ON/OFF button HOW TO JUMP START YOUR VEHICLE 21000mAh startmonkey400 unit A Flexible, insulated crocodile clips B 12V in-car charger C 16V Universal AC Mains Charger D A B D C To illuminate the screen, press the ON/OFF button for 1 second The startmonkey400 will automatically detect the voltage of the battery when attached. If 6V to 14V are detected the unit will switch on 12V 12V + 60 Seconds 12V + 12V 12V + x2 12V + 12.0 v Startmonkey 12V +
Locate the battery terminals. Check the battery is 12V and maximum 1200 Cold Cranking Amps
Leave the startmonkey400 attached to the vehicle battery for up to 60 seconds and then turn on vehicle ignition as normal
DO NOT remove the startmonkey400 if the green LED array is illuminated. The unit must be turned off first
Connect the black crocodile clip to the – terminal and the red crocodile clip to the + terminal. The startmonkey400 unit should switch on automatically
If vehicle does not start first time, remove clips and then repeat steps 2-4. In very cold temperatures this process may have to be repeated several times
If the vehicle battery is below 6V the startmonkey400 will need to be switched on manually by pressing the ON/OFF button twice in quick succession
Once the vehicle has started the startmonkey400 will turn off automatically and can be removed. The startmonkey400 can also be switched off manually by holding down the ON/OFF button
To illuminate the screen, press the ON/OFF button for 1 second
The startmonkey400 will automatically detect the voltage of the battery when attached. If 6V to 14V are detected the unit will switch on
12V
12V
+
60 Seconds
12V
+
12V
12V
+
x2
12V
+
12.0 vStartmonkey
12V
+
Designed and developed in the UK Engineered and made in China
Do not use with any other batteries apart from 12V vehicle batteries Never use the manual over-ride feature to activate the
startmonkey400 on batteries which are not rated at 12V If your vehicle will not start after it has been attached for up to 60
seconds and steps 2-4 have been repeated up to 7 times, leave the startmonkey400 attached and retry after 10 minutes. If your vehicle still will not start, please refer to your vehicle dealer
Do not remove the startmonkey400 if the green LED array is illuminated. The unit must be turned off first – to do this, hold
the ON/OFF button for 3 seconds
Never let the crocodile clips come into contact with each other unless the startmonkey400 has been turned off
If using the startmonkey400 to jump-start a marine outboard engine please ensure the startmonkey400 has been manually turned off before removing
If you require further information or assistance, please contact technical support on +44 (0) 1420 542980
To check the capacity of your startmonkey400, press the ON/OFF button for 1 second
To charge the startmonkey400 using the 16V Universal AC Mains Charger, insert the output cable into the DC IN socket and connect to the mains
You can recharge the startmonkey400 using Powertraveller’s powergorilla (not included). Connect the L52D tip to the connection cable (both supplied with powergorilla) and select the 16V setting on the powergorilla. Plug into the DC IN on the startmonkey400
The array of green LED lights will scroll up and increase as the startmonkey400 is being charged. Once all the LEDs remain solid green, the unit is fully charged
HOW TO RECHARGE THE STARTMONKEY400
Bedienungsanleitung bitte von unserer webseite runterladen
Allez sur notre site internet afin de consulter le mode d’emploi
Visitate il nostro website per scaricare le istruzioni
Visita nuestra web para descargar el manuel de usuario
Bezoek onze website om deze gebruikershandleiding te downloadenOther Powertraveller products can be purchased from
www.powertraveller.comCustomer support, email us at [email protected] powertraveller.com/startmonkey400
The 4 blocks of LEDs will indicate the amount of capacity left. Each block represents 25% of the battery’s capacity (Hint: If less than 50% we recommend you charge the unit)
To charge the startmonkey400 using the 12V in-car charger, insert the output cable into the DC IN socket and insert the 12V DC plug into the socket in your vehicle. A full charged will take approximately 4 hours from 50%
YOU CANCHARGE:
+ MANY MORE 12V BATTERIES
STARTMONKEY400 IMPORTANT INFORMATION
SPECIFICATIONS:• 7AH x 3 Lithium Polymer rechargeable battery• Battery capacity: 21,000mAh• Suitable for 12V batteries on vehicles with up to
1200 CCA• Maximum jump-start current: 400A, 4,800 Watts• Auto-on from 6V to 12V• Working temperature: -27° to 50°C• Weight: 1.1Kg• Dimensions: 210 x 65 x 64 mmAll brands and trademarks belong to their respective owners.
