Job Code 6-1720-10-0000 Doc. No. 3D-07-13F1-138

SP3D Operator Training Guide

Lab:11 Electrical Task Training

3D ENGINEERING PROPULSION GROUP

REV DATE REASON FOR ISSUE PREPD CHKD APRD 0 01/May/09 1st Issue D.Iwata T.Hayami T.Hayami

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

1 of 27

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

2 of 27

1 OUTLINE .......................................................................................................................................................... 3

1.1 Electrical Task ........................................................................................................................................... 3 2 MODELING OF CABLE TRAY ........................................................................................................................ 4

2.1 Route Cableway Command ................................................................................................................. 5 2.2 Route Cableway Command ................................................................................................................. 9

3 MODELING OF CONDUIT ............................................................................................................................. 14

3.1 Route Conduit Command ........................................................................................................................ 14 3.2 Change to Conduit Elbow ........................................................................................................................ 19

4 MODELING OF CABLE ................................................................................................................................. 21

4.1 Insert Cable Command ........................................................................................................................... 22 4.2 Confirming the Cable Path ...................................................................................................................... 26

4.2.1 Selection of Cable from Workspace Explorer ................................................................................ 26 4.2.2 Selection of Cable from Cable Selection List ................................................................................ 27

Lab:11 Electrical Task Training

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

3 of 27

1 OUTLINE

1.1 Electrical Task

In Electrical Task, mainly Cable Tray and Conduit Pipe are modeled. In addition, the cross sectional shape that is not registered in Cable Spec, called Cableway, can be modeled and used to input Cable Trench.

Cable can also be modeled. Cable Tray, Conduit Pipe and Cableway can be specified as the path of Cable.

Cable Tray

Cable way

Local Panel

Lighting Lighting

Local Control Station

Local Control Station

Cable

Cable way Conduit Pipe

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

4 of 27

2 MODELING OF CABLE TRAY

Electrical Cable Tray, like the figure below, is arranged in SP3D.

ELEC_A330_1002

BOT EL.22400

ELEC_A330_1001

Figure - 1

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

5 of 27

2.1 Route Cableway Command

Cable Tray is to be positioned on Structure Beam at EL22400 mm.

(1) From File > Define Workspace, set Filter to 2.1 Route Cable Tray.

(2) Set Active Permission to Electrical and Active WBS to WBS_Project.

(3) From the Menu, select Tasks > Electrical.

(4) From Toolbar, left-click Route Cableway command.

(5) From Common Toolbar, left-click Pin-Point Tool

(6) To determine the origin of Pin-point, left-click Reposition Target

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

6 of 27

(7) The grid intersection of EL 22.400 m should be set as Origin. To set the grid intersection point,

middle-click the first grid and left-click on the second grid.

(8) From the Pin-Point Tool ribbon bar, set E1000 mm, N-500 mm, El0 mm and left-click on the screen.

A

01B

Middle-click on the first

grid

Left-click on the

second grid

Left Click on the screen

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

7 of 27

(9) The dialog of New Cableway shall be set as shown below.

(10) Category: shall be set to Cable Fill.

(11) Key in 0.8 for Fill Efficiency, then the value will change to 80. Left-click on OK button.

(12) From the ribbon bar, select Offset Set Offset Reference

(13) Offset Reference Type shall be set to Cardinal Point. Then, select the Bottom point and left-click on OK button.

Left-click

Left-click

Left-click

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

8 of 27

(14) From the ribbon bar, set Width450 mm and Depth150 mm.

z For the Width and Depth set here, the shape of Cable Tray will generate according to what was registered in the Catalog Spec of Cable Tray.

z However, when the values specified are not registered in the Catalog Spec, Cableway will be

generated in the form of a box in gray color.

(15) From the Pin-Point Tool ribbon bar, set E1000 mm, N36500 mm, El0 mm and left-click on the screen.

(16) Then, the next direction will be asked. Right-click on the screen to finish the command.

Left Click on the screen

Right Click on the screen

Cable Tray Cableway

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

9 of 27

2.2 Route Cableway Command

From the Cable TrayELEC_A330_1002positioned above, Cable TrayELEC_A330_1001will be branched.

(1) From Toolbar, left-click on Route Cableway command.

(2) From Toolbar, activate Pin-Point Tool

Figure - 2

ELEC_A330_1002

BOT EL.22400

ELEC_A330_1001

1950 mm

EL.17000

950 mm

1000 mm1500 mm

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

10 of 27

(3) To determine the origin of Pin-Pont Tool, left-click on Reposition Target

(4) Set the intersection point of EL22.400 m as the origin. To set the intersection point, middle-click

on the first grid and left-click on the second grid.

(5) From the Pin-Point Tool ribbon bar, set N1500 mm and left-click on the Straight Feature of branch Cable Tray.

A

01B

Middle-click on the first

grid

Left-click on the second

grid

Left Click on Cable Tray

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

11 of 27

(6) New Cableway dialog shall be set as follows:

(7) Category: shall be set to Cable Fill.

(8) Key in 0.8 for Fill Efficiency, then value will be changed to 80, and left-click on OK button.

(9) From the ribbon bar, set Width450 mm and Depth150 mm.

(10) From the ribbon bar, set Offsetto .

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

12 of 27

(11) From the ribbon bar, set Planeto Plan Plane.

(12) From the Pin-Point Tool ribbon bar, set E-950 mm and then left-click on the screen.

(13) From the ribbon bar, set Plane: to No Plane.

(14) Set Coordinate System to Global.

(15) Left-click on Set Target to Origin to make the coordinates absolute.

(16) From the Pin-Point Tool ribbon bar, set El17000 mm.

Left Click on the screen

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

13 of 27

(17) When Cable Tray is being directed vertically, left-click on the screen.

(18) Then, the next direction will be asked, right-click on the screen to finish the command.

Left Click on the screen

Right Click on the screen

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

14 of 27

3 MODELING OF CONDUIT

1 Conduit Pipe will be branched from Cable TrayELEC_A330_1002.

3.1 Route Conduit Command

(1) Set Electrical as Active Permission and WBS_Project as Active WBS.

(2) From the menu, select Tasks > Electrical.

Figure - 3

ELEC_A330_1002 BOT EL.22400

Lighting HPSBT250-B1-01

1000 mm

375 mm

1000

mm

15

00 m

m

EL.21400

EL.19900

Pull Box

1 Conduit Pipe

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

15 of 27

(3) From Toolbar, left-click on Route Conduit command.

(4) From Common Toolbar, activate Pin-Point Tool

(5) To determine the origin of Pin-Pont Tool, left-click on Reposition Target

(6) The intersection point at EL 22.400 m should be set as origin. To select the intersection points of

grids, middle-click on the first grid and left-click on the second grid.

01B

Middle-click on the first

grid

Left-click on the

second grid

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

16 of 27

(7) From Pin-Point Tool ribbon bar, set N-375 mm and left-click on the Straight Feature of branch Cable Tray from Conduit Pipe.

(8) New Conduit Run dialog shall be set as shown below.

(9) Category: shall be set to Cable Fill.

(10) Key in 0.75 for Fill Efficiency, then the value will be changed to 75. Left-click on OK button.

Left Click on Cable Tray

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

17 of 27

(11) From Pin-Point Tool ribbon bar, set El-1000 mm.

(12) Left-click on the screen where Conduit Pipe directs vertically

(13) From Pin-Point Tool ribbon bar, set E0 mm.

(14) Left-click on the screen where Conduit Pipe directs horizontally

(15) From Pin-Point Tool ribbon bar, set El-2500 mm.

Left Click on the screen

Left Click on the screen

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

18 of 27

(16) Left-click on the screen where Conduit Pipe directs vertically

(17) Next, Pull Box must be placed. Left-click on Insert Component command

(18) From Type, select Pullbox.

(19) On the ribbon bar, set Reference position to Origin.

Left Click on the screen

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

19 of 27

(20) The part will be displayed dynamically. Left-click on Finish button.

(21) The next direction will be asked, right-click on the screen to finish the command.

3.2 Change to Conduit Elbow

90 Degree Elbow generated automatically is to be changed to Conduit Bend.

(1) On the Locate Filter, select Conduit Features.

(2) From the scree, left-click on 90 Degree Elbow.

Left Click on 90 deg Elbow

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

20 of 27

(3) On the ribbon bar, change Type to Conduit Bend.

(4) Change the other Elbow to Conduit Bend using the same procedure.

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

21 of 27

4 MODELING OF CABLE

Model the Cable from Control PanelECP-A330-1001to LightingHPSBT250-B1-01.

In modeling the Cable, specify Cable Tray and Conduit for the route through which the Cable will pass.

Cable Tray ELEC_A330_1002

BOT EL.22400

Lighting HPSBT250-B1-01

1 Conduit Pipe

Pull Box

Figure - 4

Cable Tray ELEC_A330_1001

Control Panel ECP-A330-1001

Cable L-11-PM-001

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

22 of 27

4.1 Insert Cable Command

(1) Set Electrical for Active Permission and WBS_Project for Active WBS.

(2) From the menu, select Tasks > Electrical.

(3) From Toolbar, left-click on Insert Cable command.

(4) Set the information on Cable Properties dialog as shown below.

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

23 of 27

(5) For Originating Device, select the object from which the Cable will start.

(6) For Terminating Device, select the object to which the Cable will end.

(7) Left-click on OK button in the dialog, and a cable connecting from the Originating and Terminating Device will be generated on the screen.

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

24 of 27

(8) From the ribbon bar, left-click Set Entry Point button.

(9) From the screen, select Cableway End Feature of Electrical Cable Tray. Upon selection of the Cable Tray, the Ribbon Bar will move to or shift to Step of Select

Cableway(s) automatically.

(10) The Cable is directed in the direction of Cable Tray From the screen, select Cableway Straight Feature.

Left - Click

Left - Click

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

25 of 27

(11) The direction in which Cable will pass is to be indicated or specified. From the screen, select Conduit Straight Feature.

(12) From the ribbon bar, left-click on Accept Selection and the ribbon bar will move to Step of

Set Exit Point automatically.

(13) To specify the point where Cable must pass, specify the port of Pull Box, and Cable will be connected to Lighting.

(14) Lastly, click on Finish to fix Cable Path.

Left - Click

Left - Click

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

26 of 27

4.2 Confirming the Cable Path

Usually, cable paths are not displayed on the screen.

To confirm the routed Cable, the following methods are available.

z To select Cable from Workspace Explorer z To select Cable from Cable Selection List

4.2.1 Selection of Cable from Workspace Explorer

(1) On the Locate Filter, select Cables.

(2) Select Cable from Workspace Explorer and the Cable on the screen will be highlighted.

Left - Click

3D ENGINEERING PROPULSION GROUP Job Code: 6-1720-10-0000 SP3D Operator Training Guide Doc. No.: 3D-07-13F1-138

3D-07-13F1-138_SP3D Operator Training Guide (Lab11 Electrical Task)EN.doc Copyright 2007 by JGC Corporation ALL Rights Reserved

27 of 27

4.2.2 Selection of Cable from Cable Selection List

(1) From the toolbar, activate Edit Cable Path

(2) Cable Selection List will be displayed.

(3) From the list, select Cable and left-click on OK button, and the Cable on the screen will be

highlighted.

Left - Click

Left - Click